Mitchell Levy [Thu, 10 Oct 2024 23:57:31 +0000 (16:57 -0700)]
x86/fpu: Avoid writing LBR bit to IA32_XSS unless supported
There are two distinct CPU features related to the use of XSAVES and LBR:
whether LBR is itself supported and whether XSAVES supports LBR. The LBR
subsystem correctly checks both in intel_pmu_arch_lbr_init(), but the
XSTATE subsystem does not.
The LBR bit is only removed from xfeatures_mask_independent when LBR is not
supported by the CPU, but there is no validation of XSTATE support.
If XSAVES does not support LBR the write to IA32_XSS causes a #GP fault,
leaving the state of IA32_XSS unchanged, i.e. zero. The fault is handled
with a warning and the boot continues.
Consequently the next XRSTORS which tries to restore supervisor state fails
with #GP because the RFBM has zero for all supervisor features, which does
not match the XCOMP_BV field.
As XFEATURE_MASK_FPSTATE includes supervisor features setting up the FPU
causes a #GP, which ends up in fpu_reset_from_exception_fixup(). That fails
due to the same problem resulting in recursive #GPs until the kernel runs
out of stack space and double faults.
Prevent this by storing the supported independent features in
fpu_kernel_cfg during XSTATE initialization and use that cached value for
retrieving the independent feature bits to be written into IA32_XSS.
[ tglx: Massaged change log ]
Fixes: f0dccc9da4c0 ("x86/fpu/xstate: Support dynamic supervisor feature for LBR") Suggested-by: Thomas Gleixner <tglx@linutronix.de>
[ Mitchell Levy: Backport to 5.15, since struct fpu_config is not
introduced until 578971f4e228 and feature masks are not included in
said struct until 1c253ff2287f ] Signed-off-by: Mitchell Levy <levymitchell0@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20240812-xsave-lbr-fix-v3-1-95bac1bf62f4@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The refcount of CQ is not protected by locks. When CQ asynchronous
events and CQ destruction are concurrent, CQ may have been released,
which will cause UAF.
Use the xa_lock() to protect the CQ refcount.
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver") Signed-off-by: Chengchang Tang <tangchengchang@huawei.com> Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://lore.kernel.org/r/20240412091616.370789-6-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Haixiao Yan <haixiao.yan.cn@windriver.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since introduced, mctp has been ignoring the returned value of
rtnl_register_module(), which could fail silently.
Handling the error allows users to view a module as an all-or-nothing
thing in terms of the rtnetlink functionality. This prevents syzkaller
from reporting spurious errors from its tests, where OOM often occurs
and module is automatically loaded.
Before commit addf9b90de22 ("net: rtnetlink: use rcu to free rtnl message
handlers"), once rtnl_msg_handlers[protocol] was allocated, the following
rtnl_register_module() for the same protocol never failed.
However, after the commit, rtnl_msg_handler[protocol][msgtype] needs to
be allocated in each rtnl_register_module(), so each call could fail.
Many callers of rtnl_register_module() do not handle the returned error,
and we need to add many error handlings.
To handle that easily, let's add wrapper functions for bulk registration
of rtnetlink message handlers.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: d51705614f66 ("mctp: Handle error of rtnl_register_module().") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add rtnl kind names instead of using raw values. We'll need to
check for DEL kind later to validate bulk flag support.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d51705614f66 ("mctp: Handle error of rtnl_register_module().") Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to init l3mdev unconditionally, else main routing table is searched
and incorrect result is returned unless strict (iif keyword) matching is
requested.
Next patch adds a selftest for this.
Fixes: 2a8a7c0eaa87 ("netfilter: nft_fib: Fix for rpath check with VRF devices") Closes: https://bugzilla.netfilter.org/show_bug.cgi?id=1761 Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently netfilter's rpfilter and fib modules implicitely initialise
->flowic_uid with 0. This is normally the root UID. However, this isn't
the case in user namespaces, where user ID 0 is mapped to a different
kernel UID. By initialising ->flowic_uid with sock_net_uid(), we get
the root UID of the user namespace, thus keeping the same behaviour
whether or not we're running in a user namepspace.
Note, this is similar to commit 8bcfd0925ef1 ("ipv4: add missing
initialization for flowi4_uid"), which fixed the rp_filter sysctl.
Fixes: 622ec2c9d524 ("net: core: add UID to flows, rules, and routes") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 05ef7055debc ("netfilter: fib: check correct rtable in vrf setups") Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the introduced field for correct operation with VRF devices instead
of conditionally overwriting flowic_oif. This is a partial revert of
commit b575b24b8eee3 ("netfilter: Fix rpfilter dropping vrf packets by
mistake"), implementing a simpler solution.
Signed-off-by: Phil Sutter <phil@nwl.cc> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de>
Stable-dep-of: 05ef7055debc ("netfilter: fib: check correct rtable in vrf setups") Signed-off-by: Sasha Levin <sashal@kernel.org>
The fundamental premise of VRF and l3mdev core code is binding a socket
to a device (l3mdev or netdev with an L3 domain) to indicate L3 scope.
Legacy code resets flowi_oif to the l3mdev losing any original port
device binding. Ben (among others) has demonstrated use cases where the
original port device binding is important and needs to be retained.
This patch handles that by adding a new entry to the common flow struct
that can indicate the l3mdev index for later rule and table matching
avoiding the need to reset flowi_oif.
In addition to allowing more use cases that require port device binds,
this patch brings a few datapath simplications:
1. l3mdev_fib_rule_match is only called when walking fib rules and
always after l3mdev_update_flow. That allows an optimization to bail
early for non-VRF type uses cases when flowi_l3mdev is not set. Also,
only that index needs to be checked for the FIB table id.
2. l3mdev_update_flow can be called with flowi_oif set to a l3mdev
(e.g., VRF) device. By resetting flowi_oif only for this case the
FLOWI_FLAG_SKIP_NH_OIF flag is not longer needed and can be removed,
removing several checks in the datapath. The flowi_iif path can be
simplified to only be called if the it is not loopback (loopback can
not be assigned to an L3 domain) and the l3mdev index is not already
set.
3. Avoid another device lookup in the output path when the fib lookup
returns a reject failure.
Note: 2 functional tests for local traffic with reject fib rules are
updated to reflect the new direct failure at FIB lookup time for ping
rather than the failure on packet path. The current code fails like this:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: Warning: source address might be selected on device other than: eth1
PING 172.16.3.1 (172.16.3.1) from 172.16.3.1 eth1: 56(84) bytes of data.
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: connect: No route to host
Signed-off-by: David Ahern <dsahern@kernel.org> Tested-by: Ben Greear <greearb@candelatech.com> Link: https://lore.kernel.org/r/20220314204551.16369-1-dsahern@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 05ef7055debc ("netfilter: fib: check correct rtable in vrf setups") Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot managed to call xt_cluster match via ebtables:
WARNING: CPU: 0 PID: 11 at net/netfilter/xt_cluster.c:72 xt_cluster_mt+0x196/0x780
[..]
ebt_do_table+0x174b/0x2a40
Module registers to NFPROTO_UNSPEC, but it assumes ipv4/ipv6 packet
processing. As this is only useful to restrict locally terminating
TCP/UDP traffic, register this for ipv4 and ipv6 family only.
Pablo points out that this is a general issue, direct users of the
set/getsockopt interface can call into targets/matches that were only
intended for use with ip(6)tables.
Check all UNSPEC matches and targets for similar issues:
- matches and targets are fine except if they assume skb_network_header()
is valid -- this is only true when called from inet layer: ip(6) stack
pulls the ip/ipv6 header into linear data area.
- targets that return XT_CONTINUE or other xtables verdicts must be
restricted too, they are incompatbile with the ebtables traverser, e.g.
EBT_CONTINUE is a completely different value than XT_CONTINUE.
Most matches/targets are changed to register for NFPROTO_IPV4/IPV6, as
they are provided for use by ip(6)tables.
The MARK target is also used by arptables, so register for NFPROTO_ARP too.
While at it, bail out if connbytes fails to enable the corresponding
conntrack family.
If hashing fails in sctp_listen_start(), the socket remains in the
LISTENING state, even though it was not added to the hash table.
This can lead to a scenario where a socket appears to be listening
without actually being accessible.
This patch ensures that if the hashing operation fails, the sk_state
is set back to CLOSED before returning an error.
Note that there is no need to undo the autobind operation if hashing
fails, as the bind port can still be used for next listen() call on
the same socket.
Fixes: 76c6d988aeb3 ("sctp: add sock_reuseport for the sock in __sctp_hash_endpoint") Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal")
changed igb_io_error_detected() to ignore non-fatal pcie errors in order
to avoid hung task that can happen when igb_down() is called multiple
times. This caused an issue when processing transient non-fatal errors.
igb_io_resume(), which is called after igb_io_error_detected(), assumes
that device is brought down by igb_io_error_detected() if the interface
is up. This resulted in panic with stacktrace below.
To fix this issue igb_io_resume() checks if the interface is running and
the device is not down this means igb_io_error_detected() did not bring
the device down and there is no need to bring it up.
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com> Fixes: 004d25060c78 ("igb: Fix igb_down hung on surprise removal") Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch addresses a macvlan leak issue in the i40e driver caused by
concurrent access to vsi->mac_filter_hash. The leak occurs when multiple
threads attempt to modify the mac_filter_hash simultaneously, leading to
inconsistent state and potential memory leaks.
To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing
vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock),
ensuring atomic operations and preventing concurrent access.
Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in
i40e_add_mac_filter() to help catch similar issues in the future.
Reproduction steps:
1. Spawn VFs and configure port vlan on them.
2. Trigger concurrent macvlan operations (e.g., adding and deleting
portvlan and/or mac filters).
3. Observe the potential memory leak and inconsistent state in the
mac_filter_hash.
This synchronization ensures the integrity of the mac_filter_hash and prevents
the described leak.
Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM") Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
netif_is_ice() works by checking the pointer to netdev ops. However, it
only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops,
so in Safe Mode it always returns false, which is unintuitive. While it
doesn't look like netif_is_ice() is currently being called anywhere in Safe
Mode, this could change and potentially lead to unexpected behaviour.
Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Performing a dummy read ensures that the register write operation is fully
completed, mitigating any potential bus delays that could otherwise impact
the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to
control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application
sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on
a delay function to ensure the clock frequency does not exceed 1 MHz.
However, this can lead to rapid toggling of the GPIO because the write
operation is POSTed and does not wait for a bus acknowledgment.
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The processor_thermal driver uses pcim_device_enable() to enable a PCI
device, which means the device will be automatically disabled on driver
detach. Thus there is no need to call pci_disable_device() again on it.
With recent PCI device resource management improvements, e.g. commit f748a07a0b64 ("PCI: Remove legacy pcim_release()"), this problem is
exposed and triggers the warining below.
The function proc_thermal_add() adds sysfs entries for power limits.
The feature mask of available features is not present at that time, so
it cannot be used by proc_thermal_add() to selectively create sysfs
attributes.
The feature mask is set by proc_thermal_mmio_add(), so modify the code
to call it before proc_thermal_add() so as to allow the latter to use
the feature mask.
There is no functional impact with this change.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 99ca0b57e49f ("thermal: intel: int340x: processor: Fix warning during module unload") Signed-off-by: Sasha Levin <sashal@kernel.org>
rfcomm_sk_state_change attempts to use sock_lock so it must never be
called with it locked but rfcomm_sock_ioctl always attempt to lock it
causing the following trace:
======================================================
WARNING: possible circular locking dependency detected 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Not tainted
------------------------------------------------------
syz-executor386/5093 is trying to acquire lock: ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1671 [inline] ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: rfcomm_sk_state_change+0x5b/0x310 net/bluetooth/rfcomm/sock.c:73
but task is already holding lock: ffff88807badfd28 (&d->lock){+.+.}-{3:3}, at: __rfcomm_dlc_close+0x226/0x6a0 net/bluetooth/rfcomm/core.c:491
Reported-by: syzbot+d7ce59b06b3eb14fd218@syzkaller.appspotmail.com Tested-by: syzbot+d7ce59b06b3eb14fd218@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=d7ce59b06b3eb14fd218 Fixes: 3241ad820dbb ("[Bluetooth] Add timestamp support to L2CAP, RFCOMM and SCO") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a kernel panic in the br_netfilter module when sending untagged
traffic via a VxLAN device.
This happens during the check for fragmentation in br_nf_dev_queue_xmit.
It is dependent on:
1) the br_netfilter module being loaded;
2) net.bridge.bridge-nf-call-iptables set to 1;
3) a bridge with a VxLAN (single-vxlan-device) netdevice as a bridge port;
4) untagged frames with size higher than the VxLAN MTU forwarded/flooded
When forwarding the untagged packet to the VxLAN bridge port, before
the netfilter hooks are called, br_handle_egress_vlan_tunnel is called and
changes the skb_dst to the tunnel dst. The tunnel_dst is a metadata type
of dst, i.e., skb_valid_dst(skb) is false, and metadata->dst.dev is NULL.
Then in the br_netfilter hooks, in br_nf_dev_queue_xmit, there's a check
for frames that needs to be fragmented: frames with higher MTU than the
VxLAN device end up calling br_nf_ip_fragment, which in turns call
ip_skb_dst_mtu.
The ip_dst_mtu tries to use the skb_dst(skb) as if it was a valid dst
with valid dst->dev, thus the crash.
This case was never supported in the first place, so drop the packet
instead.
Fix tcp_enter_recovery() so that if there are no retransmits out then
we zero retrans_stamp when entering fast recovery. This is necessary
to fix two buggy behaviors.
Currently a non-zero retrans_stamp value can persist across multiple
back-to-back loss recovery episodes. This is because we generally only
clears retrans_stamp if we are completely done with loss recoveries,
and get to tcp_try_to_open() and find !tcp_any_retrans_done(sk). This
behavior causes two bugs:
(1) When a loss recovery episode (CA_Loss or CA_Recovery) is followed
immediately by a new CA_Recovery, the retrans_stamp value can persist
and can be a time before this new CA_Recovery episode starts. That
means that timestamp-based undo will be using the wrong retrans_stamp
(a value that is too old) when comparing incoming TS ecr values to
retrans_stamp to see if the current fast recovery episode can be
undone.
(2) If there is a roughly minutes-long sequence of back-to-back fast
recovery episodes, one after another (e.g. in a shallow-buffered or
policed bottleneck), where each fast recovery successfully makes
forward progress and recovers one window of sequence space (but leaves
at least one retransmit in flight at the end of the recovery),
followed by several RTOs, then the ETIMEDOUT check may be using the
wrong retrans_stamp (a value set at the start of the first fast
recovery in the sequence). This can cause a very premature ETIMEDOUT,
killing the connection prematurely.
This commit changes the code to zero retrans_stamp when entering fast
recovery, when this is known to be safe (no retransmits are out in the
network). That ensures that when starting a fast recovery episode, and
it is safe to do so, retrans_stamp is set when we send the fast
retransmit packet. That addresses both bug (1) and bug (2) by ensuring
that (if no retransmits are out when we start a fast recovery) we use
the initial fast retransmit of this fast recovery as the time value
for undo and ETIMEDOUT calculations.
This makes intuitive sense, since the start of a new fast recovery
episode (in a scenario where no lost packets are out in the network)
means that the connection has made forward progress since the last RTO
or fast recovery, and we should thus "restart the clock" used for both
undo and ETIMEDOUT logic.
Note that if when we start fast recovery there *are* retransmits out
in the network, there can still be undesirable (1)/(2) issues. For
example, after this patch we can still have the (1) and (2) problems
in cases like this:
+ round 1: sender sends flight 1
+ round 2: sender receives SACKs and enters fast recovery 1,
retransmits some packets in flight 1 and then sends some new data as
flight 2
+ round 3: sender receives some SACKs for flight 2, notes losses, and
retransmits some packets to fill the holes in flight 2
+ fast recovery has some lost retransmits in flight 1 and continues
for one or more rounds sending retransmits for flight 1 and flight 2
+ fast recovery 1 completes when snd_una reaches high_seq at end of
flight 1
+ there are still holes in the SACK scoreboard in flight 2, so we
enter fast recovery 2, but some retransmits in the flight 2 sequence
range are still in flight (retrans_out > 0), so we can't execute the
new retrans_stamp=0 added here to clear retrans_stamp
It's not yet clear how to fix these remaining (1)/(2) issues in an
efficient way without breaking undo behavior, given that retrans_stamp
is currently used for undo and ETIMEDOUT. Perhaps the optimal (but
expensive) strategy would be to set retrans_stamp to the timestamp of
the earliest outstanding retransmit when entering fast recovery. But
at least this commit makes things better.
Note that this does not change the semantics of retrans_stamp; it
simply makes retrans_stamp accurate in some cases where it was not
before:
(1) Some loss recovery, followed by an immediate entry into a fast
recovery, where there are no retransmits out when entering the fast
recovery.
(2) When a TFO server has a SYNACK retransmit that sets retrans_stamp,
and then the ACK that completes the 3-way handshake has SACK blocks
that trigger a fast recovery. In this case when entering fast recovery
we want to zero out the retrans_stamp from the TFO SYNACK retransmit,
and set the retrans_stamp based on the timestamp of the fast recovery.
We introduce a tcp_retrans_stamp_cleanup() helper, because this
two-line sequence already appears in 3 places and is about to appear
in 2 more as a result of this bug fix patch series. Once this bug fix
patches series in the net branch makes it into the net-next branch
we'll update the 3 other call sites to use the new helper.
This is a long-standing issue. The Fixes tag below is chosen to be the
oldest commit at which the patch will apply cleanly, which is from
Linux v3.5 in 2012.
Fixes: 1fbc340514fc ("tcp: early retransmit: tcp_enter_recovery()") Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20241001200517.2756803-3-ncardwell.sw@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the TCP loss recovery undo logic in tcp_packet_delayed() so that
it can trigger undo even if TSQ prevents a fast recovery episode from
reaching tcp_retransmit_skb().
Geumhwan Yu <geumhwan.yu@samsung.com> recently reported that after
this commit from 2019:
commit bc9f38c8328e ("tcp: avoid unconditional congestion window undo
on SYN retransmit")
...and before this fix we could have buggy scenarios like the
following:
+ Due to reordering, a TCP connection receives some SACKs and enters a
spurious fast recovery.
+ TSQ prevents all invocations of tcp_retransmit_skb(), because many
skbs are queued in lower layers of the sending machine's network
stack; thus tp->retrans_stamp remains 0.
+ The connection receives a TCP timestamp ECR value echoing a
timestamp before the fast recovery, indicating that the fast
recovery was spurious.
+ The connection fails to undo the spurious fast recovery because
tp->retrans_stamp is 0, and thus tcp_packet_delayed() returns false,
due to the new logic in the 2019 commit: commit bc9f38c8328e ("tcp:
avoid unconditional congestion window undo on SYN retransmit")
This fix tweaks the logic to be more similar to the
tcp_packet_delayed() logic before bc9f38c8328e, except that we take
care not to be fooled by the FLAG_SYN_ACKED code path zeroing out
tp->retrans_stamp (the bug noted and fixed by Yuchung in bc9f38c8328e).
Note that this returns the high-level behavior of tcp_packet_delayed()
to again match the comment for the function, which says: "Nothing was
retransmitted or returned timestamp is less than timestamp of the
first retransmission." Note that this comment is in the original
2005-04-16 Linux git commit, so this is evidently long-standing
behavior.
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2a1 ("net: dp83869: Add ability to advertise Fiber connection") Signed-off-by: Ingo van Lil <inguin@gmx.de> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20241002161807.440378-1-inguin@gmx.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the node of an NFS client, some files saved in the mountpoint of the
NFS server were copied to another location of the same NFS server.
Accidentally, the nfs42_complete_copies() got a NULL-pointer dereference
crash with the following syslog:
The NULL-pointer dereference was due to nfs42_complete_copies() listed
the nfs_server->ss_copies by the field ss_copies of nfs4_copy_state.
So the nfs4_copy_state address ffff0100f98fa3f0 was offset by 0x10 and
the data accessed through this pointer was also incorrect. Generally,
the ordered list nfs4_state_owner->so_states indicate open(O_RDWR) or
open(O_WRITE) states are reclaimed firstly by nfs4_reclaim_open_state().
When destination state reclaim is failed with NFS_STATE_RECOVERY_FAILED
and copies are not deleted in nfs_server->ss_copies, the source state
may be passed to the nfs42_complete_copies() process earlier, resulting
in this crash scene finally. To solve this issue, we add a list_head
nfs_server->ss_src_copies for a server-to-server copy specially.
There is a bug currently when there are more than one VLAN defined
and any reset that affects the PF is initiated, after the reset rebuild
no traffic will pass on any VLAN but the last one created.
This is caused by the iteration though the VLANs during replay each
clearing the vsi_map bitmap of the VSI that is being replayed. The
problem is that during rhe replay, the pointer to the vsi_map bitmap
is used by each successive vlan to determine if it should be replayed
on this VSI.
The logic was that the replay of the VLAN would replace the bit in the map
before the next VLAN would iterate through. But, since the replay copies
the old bitmap pointer to filt_replay_rules and creates a new one for the
recreated VLANS, it does not do this, and leaves the old bitmap broken
to be used to replay the remaining VLANs.
Since the old bitmap will be cleaned up in post replay cleanup, there is
no need to alter it and break following VLAN replay, so don't clear the
bit.
Fixes: 334cb0626de1 ("ice: Implement VSI replay framework") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
NeilBrown says:
> The handling of NFSD_FILE_CACHE_UP is strange. nfsd_file_cache_init()
> sets it, but doesn't clear it on failure. So if nfsd_file_cache_init()
> fails for some reason, nfsd_file_cache_shutdown() would still try to
> clean up if it was called.
Reported-by: NeilBrown <neilb@suse.de> Fixes: c7b824c3d06c ("NFSD: Replace the "init once" mechanism") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rxe_comp_queue_pkt() an incoming response packet skb is enqueued to the
resp_pkts queue and then a decision is made whether to run the completer
task inline or schedule it. Finally the skb is dereferenced to bump a 'hw'
performance counter. This is wrong because if the completer task is
already running in a separate thread it may have already processed the skb
and freed it which can cause a seg fault. This has been observed
infrequently in testing at high scale.
This patch fixes this by changing the order of enqueuing the packet until
after the counter is accessed.
Link: https://lore.kernel.org/r/20240329145513.35381-4-rpearsonhpe@gmail.com Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com> Fixes: 0b1e5b99a48b ("IB/rxe: Add port protocol stats") Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
[Sherry: bp to fix CVE-2024-38544. Fix conflict due to missing commit: dccb23f6c312 ("RDMA/rxe: Split rxe_run_task() into two subroutines")
which is not necessary to backport] Signed-off-by: Sherry Yang <sherry.yang@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The values of the variables xres and yres are placed in strbuf.
These variables are obtained from strbuf1.
The strbuf1 array contains digit characters
and a space if the array contains non-digit characters.
Then, when executing sprintf(strbuf, "%ux%ux8", xres, yres);
more than 16 bytes will be written to strbuf.
It is suggested to increase the size of the strbuf array to 24.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The issue is that before entering the crash kernel, the DWC USB controller
did not perform operations such as resetting the interrupt mask bits.
After entering the crash kernel,before the USB interrupt handler
registration was completed while loading the DWC USB driver,an GINTSTS_SOF
interrupt was received.This triggered the misroute_irq process within the
GIC handling framework,ultimately leading to the misrouting of the
interrupt,causing it to be handled by the wrong interrupt handler
and resulting in the issue.
Summary:In a scenario where the kernel triggers a panic and enters
the crash kernel,it is necessary to ensure that the interrupt mask
bit is not enabled before the interrupt registration is complete.
If an interrupt reaches the CPU at this moment,it will certainly
not be handled correctly,especially in cases where this interrupt
is reported frequently.
Currently, suspend interrupt is enabled before pullup enable operation.
This will cause a suspend interrupt assert right after pullup DP. This
suspend interrupt is meaningless, so this will ignore such interrupt
by enable it after usb reset completed.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20240823073832.1702135-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For i.MX7D DRAM related mux clock, the clock source change should ONLY
be done done in low level asm code without accessing DRAM, and then
calling clk API to sync the HW clock status with clk tree, it should never
touch real clock source switch via clk API, so CLK_SET_PARENT_GATE flag
should NOT be added, otherwise, DRAM's clock parent will be disabled when
DRAM is active, and system will hang.
If there is a resource table device tree node, use the address as
the resource table address, otherwise use the address(where
.resource_table section loaded) inside the Cortex-M elf file.
And there is an update in NXP SDK that Resource Domain Control(RDC)
enabled to protect TCM, linux not able to write the TCM space when
updating resource table status and cause kernel dump. So use the address
from device tree could avoid kernel dump.
Note: NXP M4 SDK not check resource table update, so it does not matter
use whether resource table address specified in elf file or in device
tree. But to reflect the fact that if people specific resource table
address in device tree, it means people are aware and going to use it,
not the address specified in elf file.
In the switchtec_ntb_add function, it can call switchtec_ntb_init_sndev
function, then &sndev->check_link_status_work is bound with
check_link_status_work. switchtec_ntb_link_notification may be called
to start the work.
If we remove the module which will call switchtec_ntb_remove to make
cleanup, it will free sndev through kfree(sndev), while the work
mentioned above will be used. The sequence of operations that may lead
to a UAF bug is as follows:
CPU0 CPU1
| check_link_status_work
switchtec_ntb_remove |
kfree(sndev); |
| if (sndev->link_force_down)
| // use sndev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in switchtec_ntb_remove.
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per user reports, the Creative Labs EMU20k2 (Sound Blaster X-Fi
Titanium Series) generates spurious interrupts when used with
vfio-pci unless DisINTx masking support is disabled.
Thus, quirk the device to mark INTx masking as broken.
The Qualcomm SA8775P root ports don't advertise an ACS capability, but they
do provide ACS-like features to disable peer transactions and validate bus
numbers in requests.
Driver code is leaking OF node reference from of_get_parent() in
bcm53573_ilp_init(). Usage of of_get_parent() is not needed in the
first place, because the parent node will not be freed while we are
processing given node (triggered by CLK_OF_DECLARE()). Thus fix the
leak by accessing parent directly, instead of of_get_parent().
For RTRS path establishment, RTRS client initiates and completes con_num
of connections. After establishing all its connections, the information
is exchanged between the client and server through the info_req message.
During this exchange, it is essential that all connections have been
established, and the state of the RTRS srv path is CONNECTED.
So add these sanity checks, to make sure we detect and abort process in
error scenarios to avoid null pointer deref.
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://patch.msgid.link/20240821112217.41827-9-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current timeout handler of mad agent acquires/releases mad_agent_priv
lock for every timed out WRs. This causes heavy locking contention
when higher no. of WRs are to be handled inside timeout handler.
This leads to softlockup with below trace in some use cases where
rdma-cm path is used to establish connection between peer nodes
Simplified timeout handler by creating local list of timed out WRs
and invoke send handler post creating the list. The new method acquires/
releases lock once to fetch the list and hence helps to reduce locking
contetiong when processing higher no. of WRs
Some distros have grub2 config files with the lines
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
which match the skip regex defined for grub2 in get_grub_index():
$skip = '^\s*menuentry';
These false positives cause the grub number to be higher than it
should be, and the wrong kernel can end up booting.
Grub documents the menuentry command with whitespace between it and the
title, so make the skip regex reflect this.
Link: https://lore.kernel.org/20240904175530.84175-1-daniel.m.jordan@oracle.com Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Acked-by: John 'Warthog9' Hawley (Tenstorrent) <warthog9@eaglescrag.net> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the filesystem is mounted with errors=remount-ro, we were setting
SB_RDONLY flag to stop all filesystem modifications. We knew this misses
proper locking (sb->s_umount) and does not go through proper filesystem
remount procedure but it has been the way this worked since early ext2
days and it was good enough for catastrophic situation damage
mitigation. Recently, syzbot has found a way (see link) to trigger
warnings in filesystem freezing because the code got confused by
SB_RDONLY changing under its hands. Since these days we set
EXT4_FLAGS_SHUTDOWN on the superblock which is enough to stop all
filesystem modifications, modifying SB_RDONLY shouldn't be needed. So
stop doing that.
Note that insn at 0x211 is 6-byte cond jump insn now since its offset
becomes 0x80 based on previous round (0x293 - 0x213 = 0x80). At the same
time, insn at 0x292 is a 2-byte insn since its offset is -124.
pass6 will repeat the same code as in pass4. pass7 will repeat the same
code as in pass5, and so on. This will prevent eventual convergence.
Passes 1-14 are with padding = 0. At pass15, padding is 1 and related
insn looks like:
The similar code in pass14:
211: 74 7d je 0x290
213: 48 8b 77 00 mov rsi,QWORD PTR [rdi+0x0]
...
249: 48 85 d2 test rdx,rdx
24c: 74 21 je 0x26f
24e: 48 01 f7 add rdi,rsi
...
Before generating the following insn,
250: 74 21 je 0x273
"padding = 1" enables some checking to ensure nops is either 0 or 4
where
#define INSN_SZ_DIFF (((addrs[i] - addrs[i - 1]) - (prog - temp)))
nops = INSN_SZ_DIFF - 2
In this specific case,
addrs[i] = 0x24e // from pass14
addrs[i-1] = 0x24d // from pass15
prog - temp = 3 // from 'test rdx,rdx' in pass15
so
nops = -4
and this triggers the failure.
To fix the issue, we need to break cycles of je <-> jmp. For example,
in the above case, we have
211: 74 7d je 0x290
the offset is 0x7d. If 2-byte je insn is generated only if
the offset is less than 0x7d (<= 0x7c), the cycle can be
break and we can achieve the convergence.
I did some study on other cases like je <-> je, jmp <-> je and
jmp <-> jmp which may cause cycles. Those cases are not from actual
reproducible cases since it is pretty hard to construct a test case
for them. the results show that the offset <= 0x7b (0x7b = 123) should
be enough to cover all cases. This patch added a new helper to generate 8-bit
cond/uncond jmp insns only if the offset range is [-128, 123].
Adding/removing large amount of pages at once to/from the CMM balloon
can result in rcu_sched stalls or workqueue lockups, because of busy
looping w/o cond_resched().
Prevent this by adding a cond_resched(). cmm_free_pages() holds a
spin_lock while looping, so it cannot be added directly to the existing
loop. Instead, introduce a wrapper function that operates on maximum 256
pages at once, and add it there.
Disable compile time optimizations of test_facility() for the
decompressor. The decompressor should not contain any optimized code
depending on the architecture level set the kernel image is compiled
for to avoid unexpected operation exceptions.
Add a __DECOMPRESSOR check to test_facility() to enforce that
facilities are always checked during runtime for the decompressor.
Percpu map is often used, but the map value size limit often ignored,
like issue: https://github.com/iovisor/bcc/issues/2519. Actually,
percpu map value size is bound by PCPU_MIN_UNIT_SIZE, so we
can check the value size whether it exceeds PCPU_MIN_UNIT_SIZE first,
like percpu map of local_storage. Maybe the error message seems clearer
compared with "cannot allocate memory".
Signed-off-by: Jinke Han <jinkehan@didiglobal.com> Signed-off-by: Tao Chen <chen.dylane@gmail.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20240910144111.1464912-2-chen.dylane@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling irq_domain_remove() will lead to freeing the IRQ domain
prematurely. The domain is still referenced and will be attempted to get
used via rmi_free_function_list() -> rmi_unregister_function() ->
irq_dispose_mapping() -> irq_get_irq_data()'s ->domain pointer.
With PaX's MEMORY_SANITIZE this will lead to an access fault when
attempting to dereference embedded pointers, as in Torsten's report that
was faulting on the 'domain->ops->unmap' test.
Fix this by releasing the IRQ domain only after all related IRQs have
been deactivated.
This fixes the following issue discovered by code review:
after vqs have been created, a buggy device can send an interrupt.
A control vq callback will then try to schedule control_work which has
not been initialized yet. Similarly for config interrupt. Further, in
and out vq callbacks invoke find_port_by_vq which attempts to take
ports_lock which also has not been initialized.
To fix, init all locks and work before creating vqs.
Message-ID: <ad982e975a6160ad110c623c016041311ca15b4f.1726511547.git.mst@redhat.com> Fixes: 17634ba25544 ("virtio: console: Add a new MULTIPORT feature, support for generic ports") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
setup_loopback.sh and net_helper.sh are meant to be sourced from other
scripts, not executed directly. Therefore, remove the executable bits from
those files' permissions.
This change is similar to commit 49078c1b80b6 ("selftests: forwarding:
Remove executable bits from lib.sh")
Fixes: 7d1575014a63 ("selftests/net: GRO coalesce test") Fixes: 3bdd9fd29cb0 ("selftests/net: synchronize udpgro tests' tx and rx connection") Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Link: https://lore.kernel.org/r/20240131140848.360618-4-bpoirier@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sockets used by udpgso_bench_tx aren't always ready when
udpgso_bench_tx transmits packets. This issue is more prevalent in -rt
kernels, but can occur in both. Replace the hacky sleep calls with a
function that checks whether the ports in the namespace are ready for
use.
Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Lucas Karpinski <lkarpins@redhat.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 9d851dd4dab6 ("selftests: net: Remove executable bits from library scripts") Signed-off-by: Sasha Levin <sashal@kernel.org>
In some conditions, background processes in udpgro don't have enough
time to set up the sockets. When foreground processes start, this
results in the test failing with "./udpgso_bench_tx: sendmsg: Connection
refused". For instance, this happens from time to time on a Qualcomm
SA8540P SoC running CentOS Stream 9.
To fix this, increase the time given to background processes to
complete the startup before foreground processes start.
Signed-off-by: Adrien Thierry <athierry@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 9d851dd4dab6 ("selftests: net: Remove executable bits from library scripts") Signed-off-by: Sasha Levin <sashal@kernel.org>
The map_pid_to_cmdline[] is PID_MAX_DEFAULT in size and holds the index
into the other arrays. The map_cmdline_to_pid[] is a mapping back to the
full pid as it can be larger than PID_MAX_DEFAULT. And the
saved_cmdlines[] just holds the COMMs associated to the pids.
Currently the map_pid_to_cmdline[] and saved_cmdlines[] are allocated
together (in reality the saved_cmdlines is just in the memory of the
rounding of the allocation of the structure as it is always allocated in
powers of two). The map_cmdline_to_pid[] array is allocated separately.
Since the rounding to a power of two is rather large (it allows for 8000
elements in saved_cmdlines), also include the map_cmdline_to_pid[] array.
(This drops it to 6000 by default, which is still plenty for most use
cases). This saves even more memory as the map_cmdline_to_pid[] array
doesn't need to be allocated.
Link: https://lore.kernel.org/linux-trace-kernel/20240212174011.068211d9@gandalf.local.home/ Link: https://lore.kernel.org/linux-trace-kernel/20240220140703.182330529@goodmis.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Vincent Donnefort <vdonnefort@google.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Mete Durlu <meted@linux.ibm.com> Fixes: 44dc5c41b5b1 ("tracing: Fix wasted memory in saved_cmdlines logic") Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts 60be76eeabb3d ("tracing: Add size check when printing
trace_marker output"). The only reason the precision check was added
was because of a bug that miscalculated the write size of the string into
the ring buffer and it truncated it removing the terminating nul byte. On
reading the trace it crashed the kernel. But this was due to the bug in
the code that happened during development and should never happen in
practice. If anything, the precision can hide bugs where the string in the
ring buffer isn't nul terminated and it will not be checked.
The fields in the hist_entry are filled on-demand which means they only
have meaningful values when relevant sort keys are used.
So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in
the hist entry can be garbage. So it shouldn't access it
unconditionally.
I got a segfault, when I wanted to see cgroup profiles.
$ sudo perf record -a --all-cgroups --synth=cgroup true
$ sudo perf report -s cgroup
Program received signal SIGSEGV, Segmentation fault.
0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48
48 return RC_CHK_ACCESS(map)->dso;
(gdb) bt
#0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48
#1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344
#2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385
#3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true)
at util/hist.c:644
#4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0,
block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761
#5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0,
sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779
#6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015
#7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0)
at util/hist.c:1260
#8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0,
machine=0x5555560388e8) at builtin-report.c:334
#9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128,
sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232
#10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128,
sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271
#11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0,
file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354
#12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132
#13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245
#14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324
#15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342
#16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60)
at util/session.c:780
#17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688,
file_path=0x555556038ff0 "perf.data") at util/session.c:1406
As you can see the entry->ms.map was NULL even if he->ms.map has a
value. This is because 'sym' sort key is not given, so it cannot assume
whether he->ms.sym and entry->ms.sym is the same. I only checked the
'sym' sort key here as it implies 'dso' behavior (so maps are the same).
Fixes: ac01c8c4246546fd ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Matt Fleming <matt@readmodwrite.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20240826221045.1202305-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 3f8ca2e115e5 ("vhost/scsi: Extract common handling code
from control queue handler") a null pointer dereference bug can be
triggered when guest sends an SCSI AN request.
In vhost_scsi_ctl_handle_vq(), `vc.target` is assigned with
`&v_req.tmf.lun[1]` within a switch-case block and is then passed to
vhost_scsi_get_req() which extracts `vc->req` and `tpg`. However, for
a `VIRTIO_SCSI_T_AN_*` request, tpg is not required, so `vc.target` is
set to NULL in this branch. Later, in vhost_scsi_get_req(),
`vc->target` is dereferenced without being checked, leading to a null
pointer dereference bug. This bug can be triggered from guest.
When this bug occurs, the vhost_worker process is killed while holding
`vq->mutex` and the corresponding tpg will remain occupied
indefinitely.
The problem is that d_fsdata was not accessed under d_lock, because
d_release() normally is only called once the dentry is otherwise no
longer accessible but since we also call it explicitly in v9fs_remove
that lock is required:
move the hlist out of the dentry under lock then unref its fids once
they are no longer accessible.
If ENOMEM fails when the extent is splitting, we need to restore the length
of the split extent.
In the ext4_split_extent_at function, only in ext4_ext_create_new_leaf will
it alloc memory and change the shape of the extent tree,even if an ENOMEM
is returned at this time, the extent tree is still self-consistent, Just
restore the split extent lens in the function ext4_split_extent_at.
When a battery hook returns an error when adding a new battery, then
the battery hook is automatically unregistered.
However the battery hook provider cannot know that, so it will later
call battery_hook_unregister() on the already unregistered battery
hook, resulting in a crash.
Fix this by using the list head to mark already unregistered battery
hooks as already being unregistered so that they can be ignored by
battery_hook_unregister().
Fixes: fa93854f7a7e ("battery: Add the battery hooking API") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://patch.msgid.link/20241001212835.341788-3-W_Armin@gmx.de Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the conditional locking from __battery_hook_unregister()
into battery_hook_unregister() and rename the low-level function
to simplify the locking during battery hook removal.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Pali Rohár <pali@kernel.org> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://patch.msgid.link/20241001212835.341788-2-W_Armin@gmx.de Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 76959aff14a0 ("ACPI: battery: Fix possible crash when unregistering a battery hook") Signed-off-by: Sasha Levin <sashal@kernel.org>
RTL8125 added fields to the tally counter, what may result in the chip
dma'ing these new fields to unallocated memory. Therefore make sure
that the allocated memory area is big enough to hold all of the
tally counter values, even if we use only parts of it.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125") Cc: stable@vger.kernel.org Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/741d26a9-2b2b-485d-91d9-ecb302e345b5@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rectify the logical value of reset-gpio so that it is set to
0 (disabled) during power-on and to 1 (enabled) during power-off.
Set the reset-gpio to GPIO_OUT_HIGH at initialization time to make
sure it starts off in reset. Also drop the "Set XCLR" comment which
is not-so-informative.
The existing usage of imx335 had reset-gpios polarity inverted
(GPIO_ACTIVE_HIGH) in their device-tree sources. With this patch
included, those DTS will not be able to stream imx335 anymore. The
reset-gpio polarity will need to be rectified in the device-tree
sources as shown in [1] example, in order to get imx335 functional
again (as it remains in reset prior to this fix).
The RK3066 VOP sets a dma_stop bit when it's done scanning out a frame
and needs the driver to acknowledge that by clearing the bit.
Unless we clear it "between" frames, the RGB output only shows noise
instead of the picture. atomic_flush is the place for it that least
affects other code (doing it on vblank would require converting all
other usages of the reg_lock to spin_(un)lock_irq, which would affect
performance for everyone).
This seems to be a redundant synchronization mechanism that was removed
in later iterations of the VOP hardware block.
The RK3399 has a 1024-entry gamma LUT with 10 bits per component on its
"big" VOP and a 256-entry, 8 bit per component LUT on the "little" VOP.
Compared to the RK3288, it no longer requires disabling gamma while
updating the LUT. On the RK3399, the LUT can be updated at any time as
the hardware has two LUT buffers, one can be written while the other is
in use. A swap of the buffers is triggered by writing 1 to the
update_gamma_lut register.
The VOP on RK3399 has a different approach from previous versions for
setting a gamma lookup table, using an update_gamma_lut register. As
this differs from RK3288, give RK3399 its own set of "common" register
definitions.
Harden build ID parsing logic, adding explicit READ_ONCE() where it's
important to have a consistent value read and validated just once.
Also, as pointed out by Andi Kleen, we need to make sure that entire ELF
note is within a page bounds, so move the overflow check up and add an
extra note_size boundaries validation.
Fixes tag below points to the code that moved this code into
lib/buildid.c, and then subsequently was used in perf subsystem, making
this code exposed to perf_event_open() users in v5.12+.
xol_add_vma() maps the uninitialized page allocated by __create_xol_area()
into userspace. On some architectures (x86) this memory is readable even
without VM_READ, VM_EXEC results in the same pgprot_t as VM_EXEC|VM_READ,
although this doesn't really matter, debugger can read this memory anyway.
projects / thirdparty / kernel / stable.git / log
