lantiq: remove redundant includes from fritz736x DTS files
The removed lines are already included in vr9_avm_fritz736x.dtsi
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
lantiq: dts: Move the &usb_vbus nodes out of &gpio
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.
This fixed the following error reported by Luca Olivetti:
...
dwc2 1e101000.usb: DWC OTG Controller
dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
dwc2 1e101000.usb: irq 62, io mem 0x1e101000
dwc2 1e101000.usb: startup error -517
dwc2 1e101000.usb: USB bus 1 deregistered
dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517
Fixes: FS#1634 Cc: Luca Olivetti <luca@ventoso.org> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Jan Hoffmann [Fri, 3 Jul 2020 11:53:47 +0000 (13:53 +0200)]
mac80211: allow ACS restriction with fixed channel
This can be useful when a DFS channel is configured, as the ACS channel
list is taken into account when switching channels after a radar event.
For example, this allows to prevent the SRD channels from being used in
that case.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[reorder structure] Signed-off-by: David Bauer <mail@david-bauer.net>
Sunguk Lee [Thu, 2 Jul 2020 09:32:43 +0000 (18:32 +0900)]
ramips: reduce spi-max-frequency for ipTIME A8004T
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.
A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)
In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.
Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
* The only exception is ipq8064-db149, which defines
"serial0 = &uart2;", but inside a block called "alias" instead of
"aliases". It must be assumed that this is broken anyway, so we
don't touch it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the DTSI files on ipq806x had a linear inheritance:
qcom-ipq8064.dtsi
v
qcom-ipq8064-v1.0.dtsi
v
qcom-ipq8064-v2.0.dtsi
v
qcom-ipq8065.dtsi
This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.
In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).
The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:
- Many definitions can be improved by just using the innermost labels.
- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
default and enabled where needed.
- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
the appropriate settings done in the lower DTSI files directly.
- For the opp_table0 adjustments for ipq8065, just redefine what's
changed, but don't add all the untouched properties again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Thu, 2 Jul 2020 16:38:09 +0000 (01:38 +0900)]
ipq806x: move common pinmux nodes to SoC DTSI
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.
* uart0_pins : Did not touch.
* i2c4_pins : This node seems to be not used at all in dts.
Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins : The common mux node is already present in the dtsi.
Removed the duplicate nodes from dts.
* nand_pins : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.
mvebu: LS421DE: use automatic fan control with thermal zones
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.
With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.
Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.
Tested succesfully using a single Crucial BX500 SSD drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
This resolves a hazard between a mtc0 and a mfc0 instruction after
activating the DSP support. Without this fix the CPU could use the old
value again and the DSP support would not be active.
Fixes: FS#2928, FS#2899 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300] Tested-by: David Bauer <mail@david-bauer.net> [ocedo_koala/ocedo_raccoon]
Daniel Golle [Fri, 3 Jul 2020 20:57:52 +0000 (21:57 +0100)]
build,json: fix build failure in case no data is found
Only collect arch_packages if actually generating any output.
Fixes: commit f09b9319 ("build,json: store arch_packages in profiles.json"( Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Paul Spooren <mail@aparcar.org>
Antti Seppälä [Thu, 2 Jul 2020 07:53:02 +0000 (10:53 +0300)]
ath79: add support for GL.iNet GL-MiFi
Add support for the ar71xx supported GL.iNet GL-MiFi to ath79.
Specifications:
- Atheros AR9331
- 64 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet
- 2.4GHz (AR9330), 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
Flash instructions:
Vendor software is based on openwrt so you can flash the sysupgrade
image via the vendor GUI or using command line sysupgrade utility.
Make sure to not save configuration over reflash as uci settings
differ between versions.
Note on MAC addresses:
Even though the platform is capable to providing separate MAC addresses
to the interfaces vendor firmware does not seem to take advantage of
that. It appears that there is only single unique pre-programmed
address in the art partition and vendor firmware uses that for
every interface (eth0/eth1/wlan0). Similar behaviour has also been
implemented in this patch.
Note on GPIOs:
In vendor firmware the gpio controlling mini pci-e slot is named
3gcontrol while it actually controls power supply to the entire mini
pci-e slot. Therefore a more descriptive name (minipcie) was chosen.
Also during development of this patch it became apparent that the
polarity of the signal is actually active low rather than active high
that can be found in vendor firmware.
Acknowledgements:
This patch is based on earlier work[1] done by Kyson Lok. Since the
initial mailing-list submission the patch has been modified to comply
with current openwrt naming schemes and dts conventions.
John Audia [Sun, 28 Jun 2020 10:24:46 +0000 (06:24 -0400)]
ipq806x: refresh config
Based on "make kernel_menuconfig CONFIG_TARGET=generic" and 5.4.49
CONFIG_LEDS_TRIGGER_DISK has been removed by the refresh and added
back manually in order to not revert f93fcf8923aa ("ipq806x: enable
disk-activity LED trigger").
Signed-off-by: John Audia <graysky@archlinux.us>
[extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.
So, do not disable it in the first place, and drop all device-specific
status statements afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '6A08':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Paul Spooren [Tue, 30 Jun 2020 11:02:43 +0000 (01:02 -1000)]
build: store default/device packages in JSON
With this commit the `profiles.json` contain both the target specific
`default_packages` as well as the device specific `device_packages` as a
array of strings.
This information is required for downstream projects like the various
web-based interactive firmware generators.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Paul Spooren <mail@aparcar.org>
Rowan Border [Tue, 30 Jun 2020 13:35:56 +0000 (14:35 +0100)]
ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
From upstream: b8392808eb3f sch_cake: add RFC 8622 LE PHB support to CAKE diffserv handling 3f608f0c4136 sch_cake: fix a few style nits 8c95eca0bb8c sch_cake: don't call diffserv parsing code when it is not needed 9208d2863ac6 sch_cake: don't try to reallocate or unshare skb unconditionally
From netdev not yet accepted:
sch_cake: fix IP protocol handling in the presence of VLAN tags
The VLAN tag handling is actually wider than just cake so upstream are
working out how to fix it generically. We fix it here just for cake.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
David Bauer [Sun, 28 Jun 2020 23:07:00 +0000 (01:07 +0200)]
ath79: replace custom uImageArcher generation
The replaces the custom uImageArcher build step with the generic uImage
build step. The only different between these two is the difference in
the generated name.
Tested on: TP-Link Archer C59 v1
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
Lars Wessels [Thu, 25 Jun 2020 19:09:59 +0000 (21:09 +0200)]
ramips: add support for WAVLINK WL-WN577A2
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):
- Configure a TFTP server on your PC/Laptop and set its IP
to 192.168.10.100
- Rename the OpenWrt image to firmware.bin and place it in the
root folder of the TFTP server
- Power off (using the small sliding power switch on the left
side) the device and connect an ethernet cable from its LAN
or WAN port to your PC/Laptop
- Press the WPS button (and keep it pressed)
- Power on the device (using the small power switch)
- After a few seconds, when the WAN/LAN LED stops blinking
very fast, release the WPS button
- Flashing OpenWrt takes less than a minute, system will
reboot automatically
- After reboot the WPS LED will indicate the current OpenWrt
running status
Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
mvebu: move definition of factory.img out of Device/Default
The Device/Default definition in mvebu defines an IMAGE/factory.img
which is not included in IMAGES, and only used twice in the
individual definitions. Move it out of the default definition
to keep it closer to the reassignment of IMAGES and make it more
consistent with respect to other values of IMAGE/factory.img
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath79: do not build TP-Link tiny images by default
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.
Disable these images for the buildbots and prevent useless builds.
Note that these devices still build fine with default settings,
even for kernel 5.4.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Leon M. George [Thu, 25 Jul 2019 09:59:56 +0000 (11:59 +0200)]
ath79: build Compex WPJ531 cpximg files
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).
Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Alex Lewontin [Fri, 21 Feb 2020 20:56:44 +0000 (15:56 -0500)]
ramips: add support for Netgear R6080
This adds support for the Netgear R6080, aka Netgear AC1000.
The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- Delete useless HDD presence inputs: they aren't buttons, and probably
they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fbfea0e21ff66c6df432fa109c5bbb43.
Save 20.3 kB flash memory.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Qin Wei [Sat, 16 May 2020 07:51:36 +0000 (15:51 +0800)]
ramips: fix sd polling
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.
Scott Roberts [Wed, 20 May 2020 19:28:39 +0000 (13:28 -0600)]
kernel: i2c-pxa: remove slave
Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Alberto Bursi [Fri, 22 May 2020 16:49:15 +0000 (18:49 +0200)]
uboot-kirkwood: enable sata in nsa310 uboot
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.
Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Huangbin Zhan [Thu, 4 Jun 2020 13:49:54 +0000 (21:49 +0800)]
base-files: coreutil-sha256sum breaks status code
With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''.
This is caused due to:
different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum")
'/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum")
"coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum
This patch restores for 'sysupgrade' the busybox call to its sha256sum applet.
Florian Eckert [Fri, 27 Mar 2020 15:23:14 +0000 (16:23 +0100)]
target/hack-5.4: platform/x86/pcengines: revert led simswich compromise
With this change the LED subsystem is abused in the kernel to switch the
simswap. This change will be reverted, so we could use again the gpio
subsystem.
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.
ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested and working:
- Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
- 2.4 GHz Wi-Fi (correct MAC)
- 5 GHz Wi-Fi (correct MAC)
- WPS Button (tested using wifitoggle)
- LEDs
- Installation via EVA bootloader (FTP recovery)
- OpenWrt sysupgrade (both CLI and LuCI)
- Download of "urlader" (mtd0)
Not working:
- Internal USB
- DVB-C em28174+MxL251 (depends on internal USB)
Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).
Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1
Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
Hans Dedecker [Wed, 24 Jun 2020 20:30:58 +0000 (22:30 +0200)]
dropbear: fix compilation for uClibc
Backport patches which fix compile issue for uClibc-ng :
dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration]
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~
genrandom
dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'?
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~~~~~
SOCK_NONBLOCK
Sungbo Eo [Sun, 23 Feb 2020 12:39:26 +0000 (21:39 +0900)]
urandom-seed: update Makefile
- update SPDX license identifier
- use https in URL
- use default PKG_BUILD_DIR
Suggested-by: Josef Schlehofer <josef.schlehofer@nic.cz> Tested-by: Josef Schlehofer <josef.schlehofer@nic.cz> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Leon M. George [Thu, 30 Apr 2020 08:26:36 +0000 (10:26 +0200)]
mac80211: fix use of local variable
mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168cf7 ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set") Signed-off-by: Leon M. George <leon@georgemail.eu>
Edward Matijevic [Tue, 23 Jun 2020 19:50:04 +0000 (14:50 -0500)]
bcm47xx: add support for NETGEAR R6200 V1
This patch adds supports for the NETGEAR R6200 V1
This device is mainlined in Linux as of 5.4
Specification:
- SOC: Broadcom BCM4718A1 (480 MHz)
- Flash: 16MB (Macronix MX25L128)
- RAM: 128MB DDR2
- SWITCH: BCM53125
- Ethernet: 5x GE (1 WAN + 4 LAN, Inverted order)
- WLAN 2.4G: In SOC
- WLAN 5GHz: miniPCIe card, BCM4352 (ID: 4360)
- USB: 1x USB 2.0 port (Type A)
- Buttons: Reset, WLAN, WPS
- LED: Amber for Power, others need a workaround
- UART: 1x UART on PCB
LED Issues: They are controlled by a 74HC164 via bit banging(GPIO 6/7)
Firmware Install Instructions
=============================
Using the device specific .chk, use that file to perform
a normal device upgrade in the OEM admin page.
Signed-off-by: Edward Matijevic <motolav@gmail.com>
Alex Lewontin [Fri, 21 Feb 2020 20:58:12 +0000 (15:58 -0500)]
ramips: move Netgear R6120 LED trigger to DTS
This moves the trigger for the Netgear R6120's wlan2g_green LED from
base-files/etc/board.d/01_leds to the device-tree file.
This has been applied to R6120 based on findings for the very similar
Netgear R6080.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[merge case in 01_leds, slightly adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (armada-3720-uDPU.dts), which is only present
for 4.19, as it has been upstreamed before 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory, only keeping
the named exception to files-4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Roederer [Wed, 25 Dec 2019 18:20:10 +0000 (19:20 +0100)]
igmpproxy: remove some bashism
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
This follows up 3519bf4976b41c
As a result, we also need to move the and/or out of the test brackets.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[squash from two patches, adjust commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Jose Olivera [Mon, 20 May 2019 13:10:56 +0000 (21:10 +0800)]
mvebu: fix default EU regdomain for Linksys WRT AC devices
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.
The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Petr Štetiar [Tue, 23 Jun 2020 07:24:57 +0000 (09:24 +0200)]
armvirt,x86: fix build breakage of crypto ccp module
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.
where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's
then used by all devices inheriting from tplink-safeloader. Fix this by
overriding KERNEL_INITRAMFS to KERNEL variable again.
Konstantin Demin [Sun, 21 Jun 2020 12:36:47 +0000 (15:36 +0300)]
dropbear: bump to 2020.79
- drop patches (applied upstream):
* 010-backport-change-address-logging.patch
* 020-backport-ed25519-support.patch
* 021-backport-chacha20-poly1305-support.patch
- backport patches:
* 010-backport-disable-toom-and-karatsuba.patch:
reduce dropbear binary size (about ~8Kb).
- refresh patches.
- don't bother anymore with following config options
because they are disabled in upstream too:
* DROPBEAR_3DES
* DROPBEAR_ENABLE_CBC_MODE
* DROPBEAR_SHA1_96_HMAC
- explicitly disable DO_MOTD as it was before commit a1099ed:
upstream has (accidentally) switched it to 0 in release 2019.77,
but reverted back in release 2020.79.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
projects / thirdparty / openwrt.git / log
