Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083b901f001794038a08b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
In the process of switching USB config from rndis to other config,
if the hardware does not support the ->pullup callback, or the
hardware encounters a low probability fault, both of them may cause
the ->pullup callback to fail, which will then cause a system panic
(use after free).
The gadget drivers sometimes need to be unloaded regardless of the
hardware's behavior.
Analysis as follows:
=======================================================================
(1) write /config/usb_gadget/g1/UDC "none"
If gadget->ops->pullup() return an error, function rndis_close() will be
called, then it will causes a use-after-free problem.
=======================================================================
Currently this driver triggers extcon and typec state update in its
probe function, to read out current state reported by the chip and
report the correct state to upper layers. This synchronization is
performed correctly, but only in case the chip indicates a pending
interrupt in reg09 register.
This fails to cover the situation where all interrupts reported by
the chip were already handled by Linux before reboot, then the system
rebooted, and then Linux starts again. In this case, the TUSB320 no
longer reports any interrupts in reg09, and the state update does not
perform any update as it depends on that interrupt indication.
Fix this by turning tusb320_irq_handler() into a thin wrapper around
tusb320_state_update_handler(), where the later now contains the bulk
of the code of tusb320_irq_handler(), but adds new function parameter
"force_update". The "force_update" parameter can be used by the probe
function to assure that the state synchronization is always performed,
independent of the interrupt indicated in reg09. The interrupt handler
tusb320_irq_handler() callback uses force_update=false to avoid state
updates on potential spurious interrupts and retain current behavior.
Fixes: 06bc4ca115cdd ("extcon: Add driver for TI TUSB320") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221120141509.81012-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem,
which can expose details collected by the TUSB320 in a far more
precise way than extcon. Since there are existing users in the
kernel and in DT which depend on the extcon interface, keep it
for now.
Add TYPE-C interface and expose the supported supply current,
direction and connector polarity via the TYPE-C interface.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Stable-dep-of: 581c848b610d ("extcon: usbc-tusb320: Update state on probe even if no IRQ pending") Signed-off-by: Sasha Levin <sashal@kernel.org>
Move extcon code into separate functions in preparation for addition of
USB TYPE-C support. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Stable-dep-of: 581c848b610d ("extcon: usbc-tusb320: Update state on probe even if no IRQ pending") Signed-off-by: Sasha Levin <sashal@kernel.org>
Probe for omap2430 glue layer is now broken for interrupt resources in
all cases.
Commit 239071064732 ("partially Revert "usb: musb: Set the DT node on the
child device"") broke probing for SoCs using ti-sysc interconnect target
module as the dt node is not found.
Commit a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from
DT core") caused omap3 to fail with error "-ENXIO: IRQ mc not found" as
the IRQ resources are no longer automatically populated from devicetree.
Let's fix the issues by calling device_set_of_node_from_dev() only if the
SoC has been updated to probe with ti-sysc. And for legacy SoCs, let's
populate the resources manually as needed.
Note that once we have updated the SoCs to probe with proper devicetree
data in all cases, this is no longer needed. But doing that requires
patching both devicetree and SoC code, so let's fix the probe issues first.
Fixes: a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from DT core") Fixes: 239071064732 ("partially Revert "usb: musb: Set the DT node on the child device"") Cc: H. Nikolaus Schaller <hns@goldelico.com> Reported-by: Sicelo Mhlongo <absicsz@gmail.com> Tested-by: Sicelo Mhlongo <absicsz@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20221118102532.34458-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
typec_unregister_port is only called for some error paths after
typec_register_port was successful. Ensure it's called in all
cases.
Fixes: 92440202a880 ("usb: typec: tipd: Only update power status on IRQ") Signed-off-by: Sven Peter <sven@svenpeter.dev> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221114174449.34634-3-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The err_role_put error path always calls fwnode_handle_put to release
the fwnode. This path can be reached after probe itself has already
released that fwnode though. Fix that by moving fwnode_handle_put in the
happy path to the very end.
Fixes: 18a6c866bb19 ("usb: typec: tps6598x: Add USB role switching logic") Signed-off-by: Sven Peter <sven@svenpeter.dev> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221114174449.34634-2-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'fwnode' set in tcpci_parse_config() which is called
in tcpci_register_port(), its node refcount is increased
in device_get_named_child_node(). It needs be put while
exiting, so call fwnode_handle_put() in the error path of
tcpci_register_port() and in tcpci_unregister_port() to
avoid leak.
Fixes: 5e85a04c8c0d ("usb: typec: add fwnode to tcpc") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221121062416.1026192-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
typec_altmode_exit checks if ops->enter is not NULL but then calls
ops->exit a few lines below. Fix that and check for the function
pointer it's about to call instead.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes") Signed-off-by: Sven Peter <sven@svenpeter.dev> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221114165924.33487-1-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/staging/vme_user/vme_tsi148.c:1757 tsi148_dma_list_add() warn:
'&entry->list' not removed from list
In tsi148_dma_list_add(), the error path "goto err_dma" will not
remove entry->list from list->entries, but entry will be freed,
then list traversal may cause UAF.
Fix by removeing it from list->entries before free().
The code in the FOTG210 driver isn't entirely endianness-agnostic
as reported by the kernel robot sparse testing. This came to
the surface while moving the files around.
The driver is only used on little-endian systems, so this causes
no real-world regression, but it is nice to be strict and have
some compile coverage also on big endian machines, so fix it
up with the right LE accessors.
This fixes a concurrency issue addressed in commit 34cb27528398 ("UIO: Fix
concurrency issue"):
"In a SMP case there was a race condition issue between
Uio_pdrv_genirq_irqcontrol() running on one CPU and irq handler on
another CPU. Fix it by spin_locking shared resources access inside irq
handler."
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
merged, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(), thus, both had the same concurrency issue
mentioned by the above commit. However, the above patch was only applied to
the "uio_pdrv_genirq" driver.
Split out from commit 34cb27528398 ("UIO: Fix concurrency issue").
Fixes: 0a0c3b5a24bd ("Add new uio device for dynamic memory allocation") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-3-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b74351287d4b ("uio: fix a sleep-in-atomic-context bug in
uio_dmem_genirq_irqcontrol()") started calling disable_irq() without
holding the spinlock because it can sleep. However, that fix introduced
another bug: if interrupt is already disabled and a new disable request
comes in, then the spinlock is not unlocked:
('myfpga' is a simple 'uio_dmem_genirq' driver I wrote to test this)
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
introduced, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(). Then commit 34cb27528398 ("UIO: Fix concurrency
issue"), which was only applied to "uio_pdrv_genirq", ended up making them
a little different. That commit, among other things, changed disable_irq()
to disable_irq_nosync() in the implementation of irqcontrol(). The
motivation there was to avoid a deadlock between irqcontrol() and
handler(), since it added a spinlock in the irq handler, and disable_irq()
waits for the completion of the irq handler.
By changing disable_irq() to disable_irq_nosync() in irqcontrol(), we also
avoid the sleeping-while-atomic bug that commit b74351287d4b ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") was trying to
fix. Thus, this fixes the missing unlock in irqcontrol() by importing the
implementation of irqcontrol() handler from the "uio_pdrv_genirq" driver.
In the end, it reverts commit b74351287d4b ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") and change
disable_irq() to disable_irq_nosync().
It is worth noting that this still does not address the concurrency issue
fixed by commit 34cb27528398 ("UIO: Fix concurrency issue"). It will be
addressed separately in the next commits.
Split out from commit 34cb27528398 ("UIO: Fix concurrency issue").
Fixes: b74351287d4b ("uio: fix a sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-2-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If class_add_groups() returns error, the 'cp->subsys' need be
unregister, and the 'cp' need be freed.
We can not call kset_unregister() here, because the 'cls' will
be freed in callback function class_release() and it's also
freed in caller's error path, it will cause double free.
So fix this by calling kobject_del() and kfree_const(name) to
cleanup kobject. Besides, call kfree() to free the 'cp'.
The rtw_join_timeout_handler() is a timer handler that
runs in atomic context, but it could call msleep().
As a result, the sleep-in-atomic-context bug will happen.
The process is shown below:
A problem about 8250_bcm7271 create debugfs failed is triggered with the
following log given:
[ 324.516635] debugfs: Directory 'bcm7271-uart' with parent '/' already present!
The reason is that brcmuart_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of 8250_bcm7271 can never be created later.
If device_register() returns error, the 'dev' and name needs be
freed. Add a release function, and then call put_device() in the
error path, so the name is freed in kobject_cleanup() and to the
'dev' is freed in release function.
Fixes: 2e4c77bea3d8 ("m68k: dio - Kill warn_unused_result warnings") Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221109064036.1835346-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RISC-V kernels support 3,4,5-level page tables at runtime by folding
upper levels.
In case of a 3-level page table, PGDIR is folded into P4D which in turn
is folded into PUD: PGDIR_SHIFT value is correctly set to the same value
as PUD_SHIFT, but P4D_SHIFT is not, then any use of P4D_SHIFT will access
invalid address bits (all set to 1).
Fix this by dynamically defining P4D_SHIFT value, like we already do for
PGDIR_SHIFT.
Just like other data we count uses the number of bytes as the basic unit,
but discard uses the number of cmds as the statistical unit. In fact the
discard command contains the number of blocks, so let's change to the
number of bytes as the base unit.
Fixes: b0af6d491a6b ("f2fs: add app/fs io stat") Signed-off-by: Yangtao Li <frank.li@vivo.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The standard RISC-V ABIs all require 16-byte stack alignment. We're
only calling that one function on the shadow stack so I doubt it'd
result in a real issue, but might as well keep this lined up.
There are 2 ways to create IPoIB PKEY child interfaces:
1) Writing a PKEY to /sys/class/net/<ib parent interface>/create_child.
2) Using netlink with iproute.
While with sysfs the child interface has the same number of tx and
rx queues as the parent, with netlink there will always be 1 tx
and 1 rx queue for the child interface. That's because the
get_num_tx/rx_queues() netlink ops are missing and the default value
of 1 is taken for the number of queues (in rtnl_create_link()).
This change adds the get_num_tx/rx_queues() ops which allows for
interfaces with multiple queues to be created over netlink. This
constant only represents the max number of tx and rx queues on that
net device.
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. We add a new struct
'amd_geode_priv' to record pointer of the pci_dev and membase, and then
add missing pci_dev_put() for the normal and error path.
Fixes: ef5d862734b8 ("[PATCH] Add Geode HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the normal and error path.
Fixes: 96d63c0297cc ("[PATCH] Add AMD HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The patch function for the T-Head PBMT errata calls __pa_symbol() before
relocation. This crashes when CONFIG_DEBUG_VIRTUAL is enabled, because
__pa_symbol() forwards to __phys_addr_symbol(), and __phys_addr_symbol()
checks against the absolute kernel start/end address.
Fix this by checking against the kernel map instead of a symbol address.
Fixes: a35707c3d850 ("riscv: add memory-type errata for T-Head") Reviewed-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Samuel Holland <samuel@sholland.org> Link: https://lore.kernel.org/r/20221126060920.65009-1-samuel@sholland.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the memremap() called with MEMREMAP_WB maps memory using
the generic ioremap() function which breaks on system with Svpbmt
because memory mapped using _PAGE_IOREMAP page attributes is treated
as strongly-ordered non-cacheable IO memory.
To address this, we implement RISC-V specific arch_memremap_wb()
which maps memory using _PAGE_KERNEL page attributes resulting in
write-back cacheable mapping on systems with Svpbmt.
The return to userspace path in entry.S may enable interrupts without the
corresponding lockdep annotation, producing a splat[0] when DEBUG_LOCKDEP
is enabled. Simply calling __trace_hardirqs_on() here gets a bit messy
due to the use of RA to point back to ret_from_exception, so just move
the whole slow-path loop into C. It's more readable and it lets us use
local_irq_{enable,disable}(), avoiding the need for manual annotations
altogether.
[0]:
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(!lockdep_hardirqs_enabled())
WARNING: CPU: 2 PID: 1 at kernel/locking/lockdep.c:5512 check_flags+0x10a/0x1e0
Modules linked in:
CPU: 2 PID: 1 Comm: init Not tainted 6.1.0-rc4-00160-gb56b6e2b4f31 #53
Hardware name: riscv-virtio,qemu (DT)
epc : check_flags+0x10a/0x1e0
ra : check_flags+0x10a/0x1e0
<snip>
status: 0000000200000100 badaddr: 0000000000000000 cause: 0000000000000003
[<ffffffff808edb90>] lock_is_held_type+0x78/0x14e
[<ffffffff8003dae2>] __might_resched+0x26/0x22c
[<ffffffff8003dd24>] __might_sleep+0x3c/0x66
[<ffffffff80022c60>] get_signal+0x9e/0xa70
[<ffffffff800054a2>] do_notify_resume+0x6e/0x422
[<ffffffff80003c68>] ret_from_exception+0x0/0x10
irq event stamp: 44512
hardirqs last enabled at (44511): [<ffffffff808f901c>] _raw_spin_unlock_irqrestore+0x54/0x62
hardirqs last disabled at (44512): [<ffffffff80008200>] __trace_hardirqs_off+0xc/0x14
softirqs last enabled at (44472): [<ffffffff808f9fbe>] __do_softirq+0x3de/0x51e
softirqs last disabled at (44467): [<ffffffff80017760>] irq_exit+0xd6/0x104
---[ end trace 0000000000000000 ]---
possible reason: unannotated irqs-on.
Now, The address of the first two pages in the MR will be searched, which
use to speed up the lookup of the pbl table for hardware. An exception
will occur when there is only one page in this MR. This patch fix the
number of page to search.
The queried AH attr is invalid. This patch fix it.
This problem is found by rdma-core test test_mr_rereg_pd
ERROR: test_mr_rereg_pd (tests.test_mr.MRTest)
Test that cover rereg MR's PD with this flow:
----------------------------------------------------------------------
Traceback (most recent call last):
File "./tests/test_mr.py", line 157, in test_mr_rereg_pd
self.restate_qps()
File "./tests/test_mr.py", line 113, in restate_qps
self.server.qp.to_rts(self.server_qp_attr)
File "qp.pyx", line 1137, in pyverbs.qp.QP.to_rts
File "qp.pyx", line 1123, in pyverbs.qp.QP.to_rtr
pyverbs.pyverbs_error.PyverbsRDMAError: Failed to modify QP state to RTR.
Errno: 22, Invalid argument
Fixes: 926a01dc000d ("RDMA/hns: Add QP operations support for hip08 SoC") Link: https://lore.kernel.org/r/20221126102911.2921820-3-xuhaoyue1@hisilicon.com Signed-off-by: Chengchang Tang <tangchengchang@huawei.com> Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After the hns roce driver is loaded, if you modify the mac address of the
network port, the following error will appear:
__ib_cache_gid_add: unable to add gid fe80:0000:0000:0000:4600:4dff:fe22:abb5 error=-28
hns3 0000:7d:00.0 hns_0: attr path_mtu(1) invalid while modify qp
The reason for the error is that the gid being occupied will cause the
failure to modify the gid. The gid is occupied by the loopback QP used by
free mr. When the mac address is modified, the gid will change. If there
is a busy QP at this time, the gid will not be released and the
modification will fail. The QP of free mr is created using the ib
interface. The ib interface will add a reference count to the gid,
resulting in this error scenario.
Considering that free mr is solving a bug in HIP08, not an actual
business, it is not necessary to use ib interfaces.
Fixes: 70f92521584f ("RDMA/hns: Use the reserved loopback QPs to free MR before destroying MPT") Link: https://lore.kernel.org/r/20221126102911.2921820-2-xuhaoyue1@hisilicon.com Signed-off-by: Yixing Liu <liuyixing1@huawei.com> Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reset was never applied in the current implementation because Intel
Bridges owned by VMD are parentless. Internally, pci_reset_bus() applies
a reset to the parent of the PCI device supplied as argument, but in this
case it failed because there wasn't a parent.
In more detail, this change allows the VMD driver to enumerate NVMe devices
in pass-through configurations when guest reboots are performed. There was
an attempted to fix this, but later we discovered that the code inside
pci_reset_bus() wasn’t triggering secondary bus resets. Therefore, we
updated the parameters passed to it, and now NVMe SSDs attached to VMD
bridges are properly enumerated in VT-d pass-through scenarios.
Link: https://lore.kernel.org/r/20221206001637.4744-1-francisco.munoz.ruiz@linux.intel.com Fixes: 6aab5622296b ("PCI: vmd: Clean up domain before enumeration") Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@linux.intel.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com> Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the previous iteration of the while loop, the "ret" may have been
assigned a value of 0, so the error return code -EINVAL may have been
incorrectly set to 0. To fix set valid return code before calling to
goto. Also investigate each case separately as Andy suggessted.
Fixes: e711f968c49c ("IB/srp: replace custom implementation of hex2bin()") Fixes: 2a174df0c602 ("IB/srp: Use kstrtoull() instead of simple_strtoull()") Fixes: 19f313438c77 ("IB/srp: Add RDMA/CM support") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Link: https://lore.kernel.org/r/1669953638-11747-2-git-send-email-wangyufen@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the previous iteration of the while loop, the "ret" may have been
assigned a value of 0, so the error return code -EINVAL may have been
incorrectly set to 0. To fix set valid return code before calling to
goto.
Fixes: 97167e813415 ("staging/rdma/hfi1: Tune for unknown channel if configuration file is absent") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Link: https://lore.kernel.org/r/1669953638-11747-1-git-send-email-wangyufen@huawei.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disable all of drivers/infiniband/hw/ and rdmavt for UML builds until
someone needs it and provides patches to support it.
This prevents build errors in hw/qib/qib_wc_x86_64.c.
Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jason Gunthorpe <jgg@nvidia.com> Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: linux-rdma@vger.kernel.org Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-um@lists.infradead.org Link: https://lore.kernel.org/r/20221202211940.29111-1-rdunlap@infradead.org Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the PG_arch_1 we keep track if the page's data cache is clean,
architecture rely on this property to treat new pages as dirty with
respect to the data cache and perform the flushing before mapping the pages
into userspace.
This patch adds a new architecture hook, arch_clear_hugepage_flags,so that
architectures which rely on the page flags being in a particular state for
fresh allocations can adjust the flags accordingly when a page is freed
into the pool.
omap_sham_probe() calls pm_runtime_get_sync() and calls
pm_runtime_put_sync() latter to put usage_counter. However,
pm_runtime_get_sync() will increment usage_counter even it failed. Fix
it by replacing it with pm_runtime_resume_and_get() to keep usage
counter balanced.
Fixes: b359f034c8bf ("crypto: omap-sham - Convert to use pm_runtime API") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Acked-by: Mark Greer <mgreer@animalcreek.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no real point in allocating dedicated memory for the irqs array.
MAXFLOW is only 2, so it is easier to allocated the needed space
directly within the 'meson_dev' structure.
This saves some memory allocation and avoids an indirection when using the
irqs array.
Fix to return a negative error code -EINVAL instead of 0.
Fixes: 0cec19c761e5 ("crypto: qat - add support for compression for 4xxx") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When f2fs chooses GC victim in large section & LFS mode,
next_victim_seg[gc_type] is referenced first. After segment is freed,
next_victim_seg[gc_type] has the next segment number.
However, next_victim_seg[gc_type] still has the last segment number
even after the last segment of section is freed. In this case, when f2fs
chooses a victim for the next GC round, the last segment of previous victim
section is chosen as a victim.
Initialize next_victim_seg[gc_type] to NULL_SEGNO for the last segment in
large section.
Fixes: e3080b0120a1 ("f2fs: support subsectional garbage collection") Signed-off-by: Yonggil Song <yonggil.song@samsung.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If compress_extension is set, and a newly created file matches the
extension, the file could be marked as compression file. However,
if inline_data is also enabled, there is no chance to check its
extension since f2fs_should_compress() always returns false.
This patch moves set_compress_inode(), which do extension check, in
f2fs_should_compress() to check extensions before setting inline
data flag.
Fixes: 7165841d578e ("f2fs: fix to check inline_data during compressed inode conversion") Signed-off-by: Sheng Yong <shengyong@oppo.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
- Do not complete polling requests from interrupt context because the
block layer expects these requests to be completed from thread
context. From block/bio.c:
If REQ_ALLOC_CACHE is set, the final put of the bio MUST be done from
process context, not hard/soft IRQ.
Fixes: eaab9b573054 ("scsi: ufs: Implement polling support") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20221118233717.441298-1-bvanassche@acm.org Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SATA devices on an expander may be removed and not be found again when I_T
nexus reset and revalidation are processed simultaneously.
The issue comes from:
- Revalidation can remove SATA devices in link reset, e.g. in
hisi_sas_clear_nexus_ha().
- However, hisi_sas_debug_I_T_nexus_reset() polls the state of a SATA
device on an expander after sending link_reset, where it calls:
hisi_sas_debug_I_T_nexus_reset
sas_ata_wait_after_reset
ata_wait_after_reset
ata_wait_ready
smp_ata_check_ready
sas_ex_phy_discover
sas_ex_phy_discover_helper
sas_set_ex_phy
The ex_phy's change count is updated in sas_set_ex_phy(), so SATA
devices after a link reset may not be found later through revalidation.
A similar issue was reported in:
commit 0f3fce5cc77e ("[SCSI] libsas: fix ata_eh clobbering ex_phys via
smp_ata_check_ready")
commit 87c8331fcf72 ("[SCSI] libsas: prevent domain rediscovery competing
with ata error handling").
To address this issue, in hisi_sas_debug_I_T_nexus_reset(), we now call
smp_ata_check_ready_type() that only polls the device type while not
updating the ex_phy's data of libsas.
Fixes: 71453bd9d1bf ("scsi: hisi_sas: Use sas_ata_wait_after_reset() in IT nexus reset") Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com> Link: https://lore.kernel.org/r/20221118083714.4034612-5-zhanjie9@hisilicon.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/scsi/snic/snic_disc.c:307 snic_tgt_create() warn:
'&tgt->list' not removed from list
If device_add() fails in snic_tgt_create(), tgt will be freed, but
tgt->list will not be removed from snic->disc.tgt_list, then list traversal
may cause UAF.
Remove from snic->disc.tgt_list before free().
Fixes: c8806b6c9e82 ("snic: driver for Cisco SCSI HBA") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221117035100.2944812-1-cuigaosheng1@huawei.com Acked-by: Narsimhulu Musini <nmusini@cisco.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fcoe_init() calls fcoe_transport_attach(&fcoe_sw_transport), but when
fcoe_if_init() fails, &fcoe_sw_transport is not detached and leaves freed
&fcoe_sw_transport on fcoe_transports list. This causes panic when
reinserting module.
BUG: unable to handle page fault for address: fffffbfff82e2213
RIP: 0010:fcoe_transport_attach+0xe1/0x230 [libfcoe]
Call Trace:
<TASK>
do_one_initcall+0xd0/0x4e0
load_module+0x5eee/0x7210
...
Fixes: 78a582463c1e ("[SCSI] fcoe: convert fcoe.ko to become an fcoe transport provider driver") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221115092442.133088-1-chenzhongjin@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ipr_init() will not call unregister_reboot_notifier() when
pci_register_driver() fails, which causes a WARNING. Call
unregister_reboot_notifier() when pci_register_driver() fails.
Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id
string array"), the name of device is allocated dynamically, it needs be
freed when device_register() returns error.
As comment of device_register() says, one should use put_device() to give
up the reference in the error path. Fix this by calling put_device(), then
the name can be freed in kobject_cleanup(), and sdbg_host is freed in
sdebug_release_adapter().
When the device release is not set, it means the device is not initialized.
We can not call put_device() in this case. Use kfree() to free memory.
Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221112131010.3757845-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns an error, the name allocated by dev_set_name()
needs to be freed. As the comment of device_register() says, one should use
put_device() to give up the reference in the error path. Fix this by
calling put_device(), then the name can be freed in kobject_cleanup().
The 'fcf' is freed in fcoe_fcf_device_release(), so the kfree() in the
error path can be removed.
The 'ctlr' is freed in fcoe_ctlr_device_release(), so don't use the error
label, just return NULL after calling put_device().
Fixes: 9a74e884ee71 ("[SCSI] libfcoe: Add fcoe_sysfs") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221112094310.3633291-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As 'alloc_len' is user controlled data, if user tries to allocate memory
larger than(>=) MAX_ORDER, then kcalloc() will fail, it creates a stack
trace and messes up dmesg with a warning.
Add __GFP_NOWARN in order to avoid too large allocation warning. This is
detected by static analysis using smatch.
Fixes: 7db0e0c8190a ("scsi: scsi_debug: Fix buffer size of REPORT ZONES command") Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Link: https://lore.kernel.org/r/20221112070612.2121535-1-harshit.m.mogalapalli@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As 'vnum' is controlled by user, so if user tries to allocate memory larger
than(>=) MAX_ORDER, then kcalloc() will fail, it creates a stack trace and
messes up dmesg with a warning.
Add __GFP_NOWARN in order to avoid too large allocation warning. This is
detected by static analysis using smatch.
In efct_device_init(), when efct_scsi_reg_fc_transport() fails,
efct_scsi_tgt_driver_exit() is not called to release memory for
efct_scsi_tgt_driver_init() and causes memleak:
If hpsa_sas_port_add_rphy() returns an error, the 'rphy' allocated in
sas_end_device_alloc() needs to be freed. Address this by calling
sas_rphy_free() in the error path.
Fixes: d04e62b9d63a ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221111043012.1074466-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hpsa_sas_port_add_phy() returns an error, hpsa_free_sas_phy() can not be
called to free the memory because the port and the phy have not been added
yet.
Replace hpsa_free_sas_phy() with sas_phy_free() and kfree() to avoid kernel
crash in this case.
Fixes: d04e62b9d63a ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221110151129.394389-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In mpt3sas_transport_port_add(), if sas_rphy_add() returns error,
sas_rphy_free() needs be called to free the resource allocated in
sas_end_device_alloc(). Otherwise a kernel crash will happen:
Because transport_add_device() is not called when sas_rphy_add() fails, the
device is not added. When sas_rphy_remove() is subsequently called to
remove the device in the remove() path, a NULL pointer dereference happens.
Fixes: f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221109032403.1636422-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
list_for_each_entry_reverse() assumes that the iterated list is nonempty
and that every list_head is embedded in the same type, but its use in
padata_do_serial() breaks both rules.
This doesn't cause any issues now because padata_priv and padata_list
happen to have their list fields at the same offset, but we really
shouldn't be relying on that.
Fixes: bfde23ce200e ("padata: unbind parallel jobs from specific CPUs") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's a bug for BHs to be on in _do_serial as Steffen points out, so
ensure they're off in the "current task" case like they are in
padata_parallel_worker to avoid this situation.
Reported-by: syzbot+bc05445bc14148d51915@syzkaller.appspotmail.com Fixes: 4611ce224688 ("padata: allocate work structures for parallel jobs from a pool") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the past, the data for mb-skcipher test has been allocated
twice, that means the first allcated memory area is without
free, which may cause a potential memory leakage. So this
patch is to remove one allocation to fix this error.
The hpda_alloc_ctlr_info() allocates h and its field reply_map. However, in
hpsa_init_one(), if alloc_percpu() failed, the hpsa_init_one() jumps to
clean1 directly, which frees h and leaks the h->reply_map.
Fix by calling hpda_free_ctlr_info() to release h->replay_map and h instead
free h directly.
Fixes: 8b834bff1b73 ("scsi: hpsa: fix selection of reply queue") Signed-off-by: Yuan Can <yuancan@huawei.com> Link: https://lore.kernel.org/r/20221122015751.87284-1-yuancan@huawei.com Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Replace pci_epc_mem_free_addr() with pci_epf_free_space() in the
error handle path to match pci_epf_alloc_space().
Link: https://lore.kernel.org/r/20221102141014.1025893-4-Frank.Li@nxp.com Fixes: e35f56bb0330 ("PCI: endpoint: Support NTB transfer between RC and EP") Signed-off-by: Frank Li <frank.li@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In accordance with the way the device DT-node is actually defined in
arch/arm64/boot/dts/toshiba/tmpv7708.dtsi and the way the device is probed
by the DW PCIe driver there are two IRQs it actually has. It's MSI IRQ the
DT-bindings lack. Let's extend the interrupts property constraints then
and fix the schema example so one would be acceptable by the actual device
DT-bindings.
Originally as it was defined the legacy bindings the pcie_inbound_axi and
pcie_aux clock names were supposed to be used in the fsl,imx6sx-pcie and
fsl,imx8mq-pcie devices respectively. But the bindings conversion has been
incorrectly so now the fourth clock name is defined as "pcie_inbound_axi
for imx6sx-pcie, pcie_aux for imx8mq-pcie", which is completely wrong.
Let's fix that by conditionally apply the clock-names constraints based on
the compatible string content.
Link: https://lore.kernel.org/r/20221113191301.5526-2-Sergey.Semin@baikalelectronics.ru Fixes: 751ca492f131 ("dt-bindings: PCI: imx6: convert the imx pcie controller to dtschema") Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The av->net_type is not initialized before it is checked in
irdma_modify_qp_roce. This leads to an incorrect update to the ARP cache
and QP context. RoCEv2 connections might fail as result.
Set the net_type using rdma_gid_attr_network_type.
Fixes: 80005c43d4c8 ("RDMA/irdma: Use net_type to check network type") Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Link: https://lore.kernel.org/r/20221122004410.1471-1-shiraz.saleem@intel.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
pci_get_device() will increase the reference count for the returned
pci_dev, and also decrease the reference count for the input parameter
*from* if it is not NULL.
If we break out the loop in node_affinity_init() with 'dev' not NULL, we
need to call pci_dev_put() to decrease the reference count. Add missing
pci_dev_put() in error path.
Fixes: c513de490f80 ("IB/hfi1: Invalid NUMA node information can cause a divide by zero") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Link: https://lore.kernel.org/r/20221117131546.113280-1-wangxiongfeng2@huawei.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The user usually configures the number of sge through the max_send_sge
parameter when creating qp, and configures the maximum size of inline data
that can be sent through max_inline_data. Inline uses sge to fill data to
send. Expect the following:
1) When the sge space cannot hold inline data, the sge space needs to be
expanded to accommodate all inline data
2) When the sge space is enough to accommodate inline data, the upper
limit of inline data can be increased so that users can send larger
inline data
Currently case one is not implemented. When the inline data is larger than
the sge space, an error of insufficient sge space occurs. This part of
the code needs to be reimplemented according to the expected rules. The
calculation method of sge num is modified to take the maximum value of
max_send_sge and the sge for max_inline_data to solve this problem.
Fixes: 05201e01be93 ("RDMA/hns: Refactor process of setting extended sge") Fixes: 30b707886aeb ("RDMA/hns: Support inline data in extented sge space for RC") Link: https://lore.kernel.org/r/20221108133847.2304539-3-xuhaoyue1@hisilicon.com Signed-off-by: Luoyouming <luoyouming@huawei.com> Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the HNS ROCE driver, The sge is divided into standard sge and extended
sge. There are 2 standard sge in RC/XRC, and the UD standard sge is 0.
In the scenario of RC SQ inline, if the data does not exceed 32bytes, the
standard sge will be used. If it exceeds, only the extended sge will be
used to fill the data.
Currently, when filling the extended sge, max_gs is directly used as the
number of the extended sge, which did not subtract the number of standard
sge. There is a logical error. The new algorithm subtracts the number of
standard sge from max_gs to get the actual number of extended sge.
Fixes: 30b707886aeb ("RDMA/hns: Support inline data in extented sge space for RC") Link: https://lore.kernel.org/r/20221108133847.2304539-2-xuhaoyue1@hisilicon.com Signed-off-by: Luoyouming <luoyouming@huawei.com> Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue was firstly exposed since commit b18c7da63fcb ("RDMA/rxe: Fix
memory leak in error path code") and then we fixed it in commit 8ff5f5d9d8cf ("RDMA/rxe: Prevent double freeing rxe_map_set()") but this
fix was reverted together at last by commit 1e75550648da (Revert
"RDMA/rxe: Create duplicate mapping tables for FMRs")
Simply let rxe_mr_cleanup() always handle freeing the mr->map once it is
successfully allocated.
Fixes: 1e75550648da ("Revert "RDMA/rxe: Create duplicate mapping tables for FMRs"") Link: https://lore.kernel.org/r/1667099073-2-1-git-send-email-lizhijian@fujitsu.com Signed-off-by: Li Zhijian <lizhijian@fujitsu.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before q_num_set() returns.
cryptd is buggy as it tries to use sync_skcipher without going
through the proper sync_skcipher interface. In fact it doesn't
even need sync_skcipher since it's already a proper skcipher and
can easily access the request context instead of using something
off the stack.
Fixes: 36b3875a97b8 ("crypto: cryptd - Remove VLA usage of skcipher") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
If you try to allocate a memory larger than(>=) MAX_ORDER, then kmalloc()
will definitely fail. It creates a stack trace and messes up dmesg. The
user controls the size here so if they specify a too large size it will
fail.
Add __GFP_NOWARN in order to avoid too large allocation warning. This is
detected by static analysis using smatch.
Fixes: 481b5e5c7949 ("scsi: scsi_debug: add resp_write_scat function") Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Link: https://lore.kernel.org/r/20221111100526.1790533-1-harshit.m.mogalapalli@oracle.com Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When allocating PBLE's for a large CQ, it is possible
that a 2-level PBLE is returned which would cause the
CQ allocation to fail since 1-level is assumed and checked for.
Fix this by requesting a level one PBLE only.
The opcode written by HW, in the RQ CQE, is the
RoCEv2/iWARP protocol opcode from the received
packet and not the SW opcode as currently assumed.
Fix this by returning the raw operation type and
queue type in the CQE to irdma_process_cqe and add
2 helpers set_ib_wc_op_sq set_ib_wc_op_rq to map
IRDMA HW op types to IB op types.
Note that for iWARP, only Write with Immediate is
supported so the opcode can only be IB_WC_RECV_RDMA_WITH_IMM
when there is immediate data present.
A malicious user may write undefined values into memory mapped completion
queue elements status or opcode. Undefined status or opcode values will
result in out-of-bounds access to an array mapping siw internal
representation of opcode and status to RDMA core representation when
reaping CQ elements. While siw detects those undefined values, it did not
correctly set completion status to a defined value, thus defeating the
whole purpose of the check.
This bug leads to the following Smatch static checker warning:
When filling a cm_id entry, return "-EAGAIN" instead of 0 if the cm_id
doesn'the have the same port as requested, otherwise an incomplete entry
may be returned, which causes "rdam res show cm_id" to return an error.
For example on a machine with two rdma devices with "rping -C 1 -v -s"
running background, the "rdma" command fails:
$ rdma -V
rdma utility, iproute2-5.19.0
$ rdma res show cm_id
link mlx5_0/- cm-idn 0 state LISTEN ps TCP pid 28056 comm rping src-addr 0.0.0.0:7174
error: Protocol not available
While with this fix it succeeds:
$ rdma res show cm_id
link mlx5_0/- cm-idn 0 state LISTEN ps TCP pid 26395 comm rping src-addr 0.0.0.0:7174
link mlx5_1/- cm-idn 0 state LISTEN ps TCP pid 26395 comm rping src-addr 0.0.0.0:7174
The "ib_port" structure must be set before adding the sysfs kobject,
and reset after removing it, otherwise it may crash when accessing
the sysfs node:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050
Mem abort info:
ESR = 0x96000006
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000e85f5ba5
[0000000000000050] pgd=0000000848fd9003, pud=000000085b387003, pmd=0000000000000000
Internal error: Oops: 96000006 [#2] PREEMPT SMP
Modules linked in: ib_umad(O) mlx5_ib(O) nfnetlink_cttimeout(E) nfnetlink(E) act_gact(E) cls_flower(E) sch_ingress(E) openvswitch(E) nsh(E) nf_nat_ipv6(E) nf_nat_ipv4(E) nf_conncount(E) nf_nat(E) nf_conntrack(E) nf_defrag_ipv6(E) nf_defrag_ipv4(E) mst_pciconf(O) ipmi_devintf(E) ipmi_msghandler(E) ipmb_dev_int(OE) mlx5_core(O) mlxfw(O) mlxdevm(O) auxiliary(O) ib_uverbs(O) ib_core(O) mlx_compat(O) psample(E) sbsa_gwdt(E) uio_pdrv_genirq(E) uio(E) mlxbf_pmc(OE) mlxbf_gige(OE) mlxbf_tmfifo(OE) gpio_mlxbf2(OE) pwr_mlxbf(OE) mlx_trio(OE) i2c_mlxbf(OE) mlx_bootctl(OE) bluefield_edac(OE) knem(O) ip_tables(E) ipv6(E) crc_ccitt(E) [last unloaded: mst_pci]
Process grep (pid: 3372, stack limit = 0x0000000022055c92)
CPU: 5 PID: 3372 Comm: grep Tainted: G D OE 4.19.161-mlnx.47.gadcd9e3 #1
Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS BlueField:3.9.2-15-ga2403ab Sep 8 2022
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : hw_stat_port_show+0x4c/0x80 [ib_core]
lr : port_attr_show+0x40/0x58 [ib_core]
sp : ffff000029f43b50
x29: ffff000029f43b50 x28: 0000000019375000
x27: ffff8007b821a540 x26: ffff000029f43e30
x25: 0000000000008000 x24: ffff000000eaa958
x23: 0000000000001000 x22: ffff8007a4ce3000
x21: ffff8007baff8000 x20: ffff8007b9066ac0
x19: ffff8007bae97578 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000
x9 : 0000000000000000 x8 : ffff8007a4ce4000
x7 : 0000000000000000 x6 : 000000000000003f
x5 : ffff000000e6a280 x4 : ffff8007a4ce3000
x3 : 0000000000000000 x2 : aaaaaaaaaaaaaaab
x1 : ffff8007b9066a10 x0 : ffff8007baff8000
Call trace:
hw_stat_port_show+0x4c/0x80 [ib_core]
port_attr_show+0x40/0x58 [ib_core]
sysfs_kf_seq_show+0x8c/0x150
kernfs_seq_show+0x44/0x50
seq_read+0x1b4/0x45c
kernfs_fop_read+0x148/0x1d8
__vfs_read+0x58/0x180
vfs_read+0x94/0x154
ksys_read+0x68/0xd8
__arm64_sys_read+0x28/0x34
el0_svc_common+0x88/0x18c
el0_svc_handler+0x78/0x94
el0_svc+0x8/0xe8
Code: f2955562aa1603e4aa1503e0f9405683 (f9402861)
Fixes: d8a5883814b9 ("RDMA/core: Replace the ib_port_data hw_stats pointers with a ib_port pointer") Signed-off-by: Mark Zhang <markzhang@nvidia.com> Reviewed-by: Michael Guralnik <michaelgur@nvidia.com> Link: https://lore.kernel.org/r/88867e705c42c1cd2011e45201c25eecdb9fef94.1667810736.git.leonro@nvidia.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the PHY is the reference clock provider then it must be initialized
and powered on before the reset on the client is deasserted, otherwise
the link will never come up. The order was changed in cf236e0c0d59.
Restore the correct order to make the driver work again on boards where
the PHY provides the reference clock. This also changes the order for
boards where the Soc is the PHY reference clock divider, but this
shouldn't do any harm.
Link: https://lore.kernel.org/r/20221101095714.440001-1-s.hauer@pengutronix.de Fixes: cf236e0c0d59 ("PCI: imx6: Do not hide PHY driver callbacks and refine the error handling") Tested-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
MSI remapping is disabled by VMD driver for Intel's Icelake and
newer systems in order to improve performance by setting
VMCONFIG_MSI_REMAP. By design VMCONFIG_MSI_REMAP register is cleared
by firmware during boot. The same register gets cleared when system
is put in S3 power state. VMD driver needs to set this register again
in order to avoid interrupt issues with devices behind VMD if MSI
remapping was disabled before.
Link: https://lore.kernel.org/r/20221109142652.450998-1-nirmal.patel@linux.intel.com Fixes: ee81ee84f873 ("PCI: vmd: Disable MSI-X remapping when possible") Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Francisco Munoz <francisco.munoz.ruiz@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Correctly set send queue element opcode during immediate work request
flushing in post sendqueue operation, if the QP is in ERROR state.
An undefined ocode value results in out-of-bounds access to an array
for mapping the opcode between siw internal and RDMA core representation
in work completion generation. It resulted in a KASAN BUG report
of type 'global-out-of-bounds' during NFSoRDMA testing.
This patch further fixes a potential case of a malicious user which may
write undefined values for completion queue elements status or opcode,
if the CQ is memory mapped to user land. It avoids the same out-of-bounds
access to arrays for status and opcode mapping as described above.
Fixes: 303ae1cdfdf7 ("rdma/siw: application interface") Fixes: b0fff7317bb4 ("rdma/siw: completion queue methods") Reported-by: Olga Kornievskaia <kolga@netapp.com> Reviewed-by: Tom Talpey <tom@talpey.com> Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Link: https://lore.kernel.org/r/20221107145057.895747-1-bmt@zurich.ibm.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/scsi/qla2xxx/qla_init.c: In function ‘qla24xx_async_abort_cmd’:
drivers/scsi/qla2xxx/qla_init.c:171:17: warning: variable ‘bail’ set but not used [-Wunused-but-set-variable]
171 | uint8_t bail;
| ^~~~
drivers/scsi/qla2xxx/qla_init.c: In function ‘qla2x00_async_tm_cmd’:
drivers/scsi/qla2xxx/qla_init.c:2023:17: warning: variable ‘bail’ set but not used [-Wunused-but-set-variable]
2023 | uint8_t bail;
| ^~~~
projects / thirdparty / kernel / stable.git / log
