Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94c2 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the array gpmc_cs is indexed by cs before it cs is range checked
and the pointer read from this out-of-index read is dereferenced. Fix this
by performing the range check on cs before the read and the following
pointer dereference.
Addresses-Coverity: ("Negative array index read") Fixes: 9ed7a776eb50 ("ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210223193821.17232-1-colin.king@canonical.com Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a12138 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
The quirk entry for Uniwill ECS M31EI is with the PCI SSID device 0,
which means matching with all. That is, it's essentially equivalent
with SND_PCI_QUIRK_VENDOR(0x1584), which also matches with the
previous entry for Haier W18 applying the very same quirk.
Let's unify them with the single vendor-quirk entry.
Just re-order the alc269_fixup_tbl[] entries for Sony devices for
avoiding the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Just re-order the alc882_fixup_tbl[] entries for Sony devices for
avoiding the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Just re-order the alc882_fixup_tbl[] entries for Acer devices for
avoiding the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Currently the ioctl command RADEON_INFO_SI_BACKEND_ENABLED_MASK can
copy back uninitialised data in value_tmp that pointer *value points
to. This can occur when rdev->family is less than CHIP_BONAIRE and
less than CHIP_TAHITI. Fix this by adding in a missing -EINVAL
so that no invalid value is copied back to userspace.
Addresses-Coverity: ("Uninitialized scalar variable) Cc: stable@vger.kernel.org # 3.13+ Fixes: 439a1cfffe2c ("drm/radeon: expose render backend mask to the userspace") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we overflow the maximum number of BSS entries and free the
new entry, drop it from any hidden_list that it may have been
added to in the code above or in cfg80211_combine_bsses().
commit d3374825ce57 ("md: make devices disappear when they are no longer
needed.") introduced protection between mddev creating & removing. The
md_open shouldn't create mddev when all_mddevs list doesn't contain
mddev. With currently code logic, there will be very easy to trigger
soft lockup in non-preempt env.
This patch changes md_open returning from -ERESTARTSYS to -EBUSY, which
will break the infinitely retry when md_open enter racing area.
This patch is partly fix soft lockup issue, full fix needs mddev_find
is split into two functions: mddev_find & mddev_find_or_alloc. And
md_open should call new mddev_find (it only does searching job).
For more detail, please refer with Christoph's "split mddev_find" patch
in later commits.
*** env ***
kvm-qemu VM 2C1G with 2 iscsi luns
kernel should be non-preempt
I use mdcluster env to trigger soft lockup, but it isn't mdcluster
speical bug. To stop md array in mdcluster env will do more jobs than
non-cluster array, which will leave enough time/gap to allow kernel to
run md_open.
"mdadm -A" (or other array assemble commands) will start a daemon "mdadm
--monitor" by default. When "mdadm -Ss" is running, the stop action will
wakeup "mdadm --monitor". The "--monitor" daemon will immediately get
info from /proc/mdstat. This time mddev in kernel still exist, so
/proc/mdstat still show md device, which makes "mdadm --monitor" to open
/dev/md0.
The previously "mdadm -Ss" is removing action, the "mdadm --monitor"
open action will trigger md_open which is creating action. Racing is
happening.
```
<thread 1>: "mdadm -Ss"
md_release
mddev_put deletes mddev from all_mddevs
queue_work for mddev_delayed_delete
at this time, "/dev/md0" is still available for opening
<thread 2>: "mdadm --monitor ..."
md_open
+ mddev_find can't find mddev of /dev/md0, and create a new mddev and
| return.
+ trigger "if (mddev->gendisk != bdev->bd_disk)" and return
-ERESTARTSYS.
```
In non-preempt kernel, <thread 2> is occupying on current CPU. and
mddev_delayed_delete which was created in <thread 1> also can't be
schedule.
In preempt kernel, it can also trigger above racing. But kernel doesn't
allow one thread running on a CPU all the time. after <thread 2> running
some time, the later "mdadm -A" (refer above script line 13) will call
md_alloc to alloc a new gendisk for mddev. it will break md_open
statement "if (mddev->gendisk != bdev->bd_disk)" and return 0 to caller,
the soft lockup is broken.
Cc: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Zhao Heming <heming.zhao@suse.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that a fix to the ring buffer recursion detection would
cause a hung machine when performing suspend / resume testing. The
following backtrace was extracted from debugging that case:
Since the fix to the recursion detection would allow a single recursion to
happen while tracing, this lead to the trace_clock_global() taking a spin
lock and then trying to take it again:
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* lock taken */
(something else gets traced by function graph tracer)
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* DEAD LOCK! */
Tracing should *never* block, as it can lead to strange lockups like the
above.
Restructure the trace_clock_global() code to instead of simply taking a
lock to update the recorded "prev_time" simply use it, as two events
happening on two different CPUs that calls this at the same time, really
doesn't matter which one goes first. Use a trylock to grab the lock for
updating the prev_time, and if it fails, simply try again the next time.
If it failed to be taken, that means something else is already updating
it.
Link: https://lkml.kernel.org/r/20210430121758.650b6e8a@gandalf.local.home Cc: stable@vger.kernel.org Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru> Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com> Fixes: b02414c8f045 ("ring-buffer: Fix recursion protection transitions between interrupt context") # started showing the problem Fixes: 14131f2f98ac3 ("tracing: implement trace_clock_*() APIs") # where the bug happened
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212761 Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default max PID is set by PID_MAX_DEFAULT, and the tracing
infrastructure uses this number to map PIDs to the comm names of the
tasks, such output of the trace can show names from the recorded PIDs in
the ring buffer. This mapping is also exported to user space via the
"saved_cmdlines" file in the tracefs directory.
But currently the mapping expects the PIDs to be less than
PID_MAX_DEFAULT, which is the default maximum and not the real maximum.
Recently, systemd will increases the maximum value of a PID on the system,
and when tasks are traced that have a PID higher than PID_MAX_DEFAULT, its
comm is not recorded. This leads to the entire trace to have "<...>" as
the comm name, which is pretty useless.
Instead, keep the array mapping the size of PID_MAX_DEFAULT, but instead
of just mapping the index to the comm, map a mask of the PID
(PID_MAX_DEFAULT - 1) to the comm, and find the full PID from the
map_cmdline_to_pid array (that already exists).
This bug goes back to the beginning of ftrace, but hasn't been an issue
until user space started increasing the maximum value of PIDs.
Currently we stop recording comm for non-idle tasks when switching from/to idle
task since we treat that as a record failure. Fix that by treat recording of
comm for idle task as a success.
Link: http://lkml.kernel.org/r/20170706230023.17942-1-joelaf@google.com Cc: kernel-team@android.com Cc: Ingo Molnar <mingo@redhat.com> Reported-by: Michael Sartain <mikesart@gmail.com> Signed-off-by: Joel Fernandes <joelaf@google.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Strcpy is inherently not safe, and strlcpy() should be used instead.
__trace_find_cmdline() uses strcpy() because the comms saved must have a
terminating nul character, but it doesn't hurt to add the extra protection
of using strlcpy() instead of strcpy().
Link: http://lkml.kernel.org/r/1493806274-13936-1-git-send-email-amit.pundir@linaro.org Signed-off-by: Amey Telawane <ameyt@codeaurora.org>
[AmitP: Cherry-picked this commit from CodeAurora kernel/msm-3.10
https://source.codeaurora.org/quic/la/kernel/msm-3.10/commit/?id=2161ae9a70b12cf18ac8e5952a20161ffbccb477] Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
[ Updated change log and removed the "- 1" from len parameter ] Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KMSAN complains that the vmci_use_ppn64() == false path in
vmci_dbell_register_notification_bitmap() left upper 32bits of
bitmap_set_msg.bitmap_ppn64 member uninitialized.
Local variable ----bitmap_set_msg@vmci_dbell_register_notification_bitmap created at:
vmci_dbell_register_notification_bitmap+0x50/0x1e0
vmci_dbell_register_notification_bitmap+0x50/0x1e0
Bytes 28-31 of 32 are uninitialized
Memory access of size 32 starts at ffff88810098f570
=====================================================
Before this commit lis3lv02d_get_pwron_wait() had a WARN_ONCE() to catch
a potential divide by 0. WARN macros should only be used to catch internal
kernel bugs and that is not the case here. We have been receiving a lot of
bug reports about kernel backtraces caused by this WARN.
The div value being checked comes from the lis3->odrs[] array. Which
is sized to be a power-of-2 matching the number of bits in lis3->odr_mask.
The only lis3 model where this array is not entirely filled with non zero
values. IOW the only model where we can hit the div == 0 check is the
3dc ("8 bits 3DC sensor") model:
Note the 0 value at index 0, according to the datasheet an odr index of 0
means "Power-down mode". HP typically uses a lis3 accelerometer for HDD
fall protection. What I believe is happening here is that on newer
HP devices, which only contain a SDD, the BIOS is leaving the lis3 device
powered-down since it is not used for HDD fall protection.
Note that the lis3_3dc_rates array initializer only specifies 10 values,
which matches the datasheet. So it also contains 6 zero values at the end.
Replace the WARN with a normal check, which treats an odr index of 0
as power-down and uses a normal dev_err() to report the error in case
odr index point past the initialized part of the array.
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
For those systems the PCI BARs that request a mapping in the I/O space
have the length recorded in the corresponding PCI resource set to zero,
which makes it unassigned:
# lspci -s 0031:02:04.0 -v
0031:02:04.0 FDDI network controller: Digital Equipment Corporation PCI-to-PDQ Interface Chip [PFI] FDDI (DEFPA) (rev 02)
Subsystem: Digital Equipment Corporation FDDIcontroller/PCI (DEFPA)
Flags: bus master, medium devsel, latency 136, IRQ 57, NUMA node 8
Memory at 620c080020000 (32-bit, non-prefetchable) [size=128]
I/O ports at <unassigned> [disabled]
Memory at 620c080030000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Kernel driver in use: defxx
Kernel modules: defxx
#
Regardless the driver goes ahead and requests it (here observed with a
Raptor Talos II POWER9 system), resulting in an odd /proc/ioport entry:
Furthermore, the system gets confused as the driver actually continues
and pokes at those locations, causing a flood of messages being output
to the system console by the underlying system firmware, like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
defxx 0031:02:04.0: enabling device (0140 -> 0142)
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010000
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
and so on and so on (possibly intermixed actually, as there's no locking
between the kernel and the firmware in console port access with this
particular system, but cleaned up above for clarity), and once some 10k
of such pairs of the latter two messages have been produced an interace
eventually shows up in a useless state:
This was not expected to happen as resource handling was added to the
driver a while ago, because it was not known at that time that a PCI
system would be possible that cannot assign port I/O resources, and
oddly enough `request_region' does not fail, which would have caught it.
Correct the problem then by checking for the length of zero for the CSR
resource and bail out gracefully refusing to register an interface if
that turns out to be the case, producing messages like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
0031:02:04.0: Cannot use I/O, no address set, aborting
0031:02:04.0: Recompile driver with "CONFIG_DEFXX_MMIO=y"
Keep the original check for the EISA MMIO resource as implemented,
because in that case the length is hardwired to 0x400 as a consequence
of how the compare/mask address decoding works in the ESIC chip and it
is only the base address that is set to zero if MMIO has been disabled
for the adapter in EISA configuration, which in turn could be a valid
bus address in a legacy-free system implementing PCI, especially for
port I/O.
Where the EISA MMIO resource has been disabled for the adapter in EISA
configuration this arrangement keeps producing messages like:
eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
00:05: Cannot use MMIO, no address set, aborting
00:05: Recompile driver with "CONFIG_DEFXX_MMIO=n"
00:05: Or run ECU and set adapter's MMIO location
with the last two lines now swapped for easier handling in the driver.
There is no need to check for and catch the case of a port I/O resource
not having been assigned for EISA as the adapter uses the slot-specific
I/O space, which gets assigned by how EISA has been specified and maps
directly to the particular slot an option card has been placed in. And
the EISA variant of the adapter has additional registers that are only
accessible via the port I/O space anyway.
While at it factor out the error message calls into helpers and fix an
argument order bug with the `pr_err' call now in `dfx_register_res_err'.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: 4d0438e56a8f ("defxx: Clean up DEFEA resource management") Cc: stable@vger.kernel.org # v3.19+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()")
and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
fixed a refcount leak bug in bind/connect but introduced a
use-after-free if the same local is assigned to 2 different sockets.
This can be triggered by the following simple program:
int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) );
addr.sa_family = AF_NFC;
addr.nfc_protocol = NFC_PROTO_NFC_DEP;
bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
close(sock1);
close(sock2);
Fix this by assigning NULL to llcp_sock->local after calling
nfc_llcp_local_put.
This addresses CVE-2021-23134.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com> Reported-by: Nadav Markus <nmarkus@paloaltonetworks.com> Fixes: c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()") Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: George Kennedy <george.kennedy@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hci_chan can be created in 2 places: hci_loglink_complete_evt() if
it is an AMP hci_chan, or l2cap_conn_add() otherwise. In theory,
Only AMP hci_chan should be removed by a call to
hci_disconn_loglink_complete_evt(). However, the controller might mess
up, call that function, and destroy an hci_chan which is not initiated
by hci_loglink_complete_evt().
This patch adds a verification that the destroyed hci_chan must have
been init'd by hci_loglink_complete_evt().
Memory state around the buggy address: ffff8881d7af9080: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff8881d7af9100: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8881d7af9180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881d7af9200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881d7af9280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
This division bug meant the search for free metadata space could skip
the final allocation bitmap's worth of entries. Fix affects DM thinp,
cache and era targets.
Cc: stable@vger.kernel.org Signed-off-by: Joe Thornber <ejt@redhat.com> Tested-by: Ming-Hung Tsai <mtsai@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes bug with the handling of more than one language in
the string table in f_fs.c.
str_count was not reset for subsequent language codes.
str_count-- "rolls under" and processes u32 max strings on
the processing of the second language entry.
The existing bug can be reproduced by adding a second language table
to the structure "strings" in tools/usb/ffs-test.c.
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
We should set the error code when ext4_commit_super check argument failed.
Found in code review. Fixes: c4be0c1dc4cdc ("filesystem freeze: add error handling of write_super_lockfs/unlockfs"). Cc: stable@kernel.org Signed-off-by: Fengnan Chang <changfengnan@vivo.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Link: https://lore.kernel.org/r/20210402101631.561-1-changfengnan@vivo.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit <50122847007> ("ext4: fix check to prevent initializing reserved
inodes") check the block group zero and prevent initializing reserved
inodes. But in some special cases, the reserved inode may not all belong
to the group zero, it may exist into the second group if we format
filesystem below.
So, it will end up triggering a false positive report of a corrupted
file system. This patch fix it by avoid check reserved inodes if no free
inode blocks will be zeroed.
Cc: stable@kernel.org Fixes: 50122847007 ("ext4: fix check to prevent initializing reserved inodes") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Suggested-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210331121516.2243099-1-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is that the parsing in the write function only processes
commands if it finished parsing (there is white space written after the
command). That's to handle:
cases, where the command is broken over multiple writes.
The problem is if the file descriptor is closed, then the write call is
not processed, and the command needs to be processed in the release code.
The release code can handle matching of functions, but does not handle
commands.
Cc: stable@vger.kernel.org Fixes: eda1e32855656 ("tracing: handle broken names in ftrace filter") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN reports a BUG when download file in jffs2 filesystem.It is
because when dstlen == 1, cpage_out will write array out of bounds.
Actually, data will not be compressed in jffs2_zlib_compress() if
data's length less than 4.
[ 393.799778] BUG: KASAN: slab-out-of-bounds in jffs2_rtime_compress+0x214/0x2f0 at addr ffff800062e3b281
[ 393.809166] Write of size 1 by task tftp/2918
[ 393.813526] CPU: 3 PID: 2918 Comm: tftp Tainted: G B 4.9.115-rt93-EMBSYS-CGEL-6.1.R6-dirty #1
[ 393.823173] Hardware name: LS1043A RDB Board (DT)
[ 393.827870] Call trace:
[ 393.830322] [<ffff20000808c700>] dump_backtrace+0x0/0x2f0
[ 393.835721] [<ffff20000808ca04>] show_stack+0x14/0x20
[ 393.840774] [<ffff2000086ef700>] dump_stack+0x90/0xb0
[ 393.845829] [<ffff20000827b19c>] kasan_object_err+0x24/0x80
[ 393.851402] [<ffff20000827b404>] kasan_report_error+0x1b4/0x4d8
[ 393.857323] [<ffff20000827bae8>] kasan_report+0x38/0x40
[ 393.862548] [<ffff200008279d44>] __asan_store1+0x4c/0x58
[ 393.867859] [<ffff2000084ce2ec>] jffs2_rtime_compress+0x214/0x2f0
[ 393.873955] [<ffff2000084bb3b0>] jffs2_selected_compress+0x178/0x2a0
[ 393.880308] [<ffff2000084bb530>] jffs2_compress+0x58/0x478
[ 393.885796] [<ffff2000084c5b34>] jffs2_write_inode_range+0x13c/0x450
[ 393.892150] [<ffff2000084be0b8>] jffs2_write_end+0x2a8/0x4a0
[ 393.897811] [<ffff2000081f3008>] generic_perform_write+0x1c0/0x280
[ 393.903990] [<ffff2000081f5074>] __generic_file_write_iter+0x1c4/0x228
[ 393.910517] [<ffff2000081f5210>] generic_file_write_iter+0x138/0x288
[ 393.916870] [<ffff20000829ec1c>] __vfs_write+0x1b4/0x238
[ 393.922181] [<ffff20000829ff00>] vfs_write+0xd0/0x238
[ 393.927232] [<ffff2000082a1ba8>] SyS_write+0xa0/0x110
[ 393.932283] [<ffff20000808429c>] __sys_trace_return+0x0/0x4
[ 393.937851] Object at ffff800062e3b280, in cache kmalloc-64 size: 64
[ 393.944197] Allocated:
[ 393.946552] PID = 2918
[ 393.948913] save_stack_trace_tsk+0x0/0x220
[ 393.953096] save_stack_trace+0x18/0x20
[ 393.956932] kasan_kmalloc+0xd8/0x188
[ 393.960594] __kmalloc+0x144/0x238
[ 393.963994] jffs2_selected_compress+0x48/0x2a0
[ 393.968524] jffs2_compress+0x58/0x478
[ 393.972273] jffs2_write_inode_range+0x13c/0x450
[ 393.976889] jffs2_write_end+0x2a8/0x4a0
[ 393.980810] generic_perform_write+0x1c0/0x280
[ 393.985251] __generic_file_write_iter+0x1c4/0x228
[ 393.990040] generic_file_write_iter+0x138/0x288
[ 393.994655] __vfs_write+0x1b4/0x238
[ 393.998228] vfs_write+0xd0/0x238
[ 394.001543] SyS_write+0xa0/0x110
[ 394.004856] __sys_trace_return+0x0/0x4
[ 394.008684] Freed:
[ 394.010691] PID = 2918
[ 394.013051] save_stack_trace_tsk+0x0/0x220
[ 394.017233] save_stack_trace+0x18/0x20
[ 394.021069] kasan_slab_free+0x88/0x188
[ 394.024902] kfree+0x6c/0x1d8
[ 394.027868] jffs2_sum_write_sumnode+0x2c4/0x880
[ 394.032486] jffs2_do_reserve_space+0x198/0x598
[ 394.037016] jffs2_reserve_space+0x3f8/0x4d8
[ 394.041286] jffs2_write_inode_range+0xf0/0x450
[ 394.045816] jffs2_write_end+0x2a8/0x4a0
[ 394.049737] generic_perform_write+0x1c0/0x280
[ 394.054179] __generic_file_write_iter+0x1c4/0x228
[ 394.058968] generic_file_write_iter+0x138/0x288
[ 394.063583] __vfs_write+0x1b4/0x238
[ 394.067157] vfs_write+0xd0/0x238
[ 394.070470] SyS_write+0xa0/0x110
[ 394.073783] __sys_trace_return+0x0/0x4
[ 394.077612] Memory state around the buggy address:
[ 394.082404] ffff800062e3b180: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
[ 394.089623] ffff800062e3b200: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
[ 394.096842] >ffff800062e3b280: 01 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 394.104056] ^
[ 394.107283] ffff800062e3b300: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 394.114502] ffff800062e3b380: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 394.121718] ==================================================================
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn> Cc: Joel Stanley <joel@jms.id.au> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few archs like powerpc have different errno.h values for macros
EDEADLOCK and EDEADLK. In code including both libc and linux versions of
errno.h, this can result in multiple definitions of EDEADLOCK in the
include chain. Definitions to the same value (e.g. seen with mips) do
not raise warnings, but on powerpc there are redefinitions changing the
value, which raise warnings and errors (if using "-Werror").
Guard against these redefinitions to avoid build errors like the following,
first seen cross-compiling libbpf v5.8.9 for powerpc using GCC 8.4.0 with
musl 1.1.24:
In file included from ../../arch/powerpc/include/uapi/asm/errno.h:5,
from ../../include/linux/err.h:8,
from libbpf.c:29:
../../include/uapi/asm-generic/errno.h:40: error: "EDEADLOCK" redefined [-Werror]
#define EDEADLOCK EDEADLK
In file included from toolchain-powerpc_8540_gcc-8.4.0_musl/include/errno.h:10,
from libbpf.c:26:
toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/errno.h:58: note: this is the location of the previous definition
#define EDEADLOCK 58
During the EEH MMIO error checking, the current implementation fails to map
the (virtual) MMIO address back to the pci device on radix with hugepage
mappings for I/O. This results into failure to dispatch EEH event with no
recovery even when EEH capability has been enabled on the device.
In case of hugepage mappings, eeh_token_to_phys() has a bug in virt -> phys
translation that results in wrong physical address, which is then passed to
eeh_addr_cache_get_dev() to match it against cached pci I/O address ranges
to get to a PCI device. Hence, it fails to find a match and the EEH event
never gets dispatched leaving the device in failed state.
The commit 33439620680be ("powerpc/eeh: Handle hugepages in ioremap space")
introduced following logic to translate virt to phys for hugepage mappings:
eeh_token_to_phys():
+ pa = pte_pfn(*ptep);
+
+ /* On radix we can do hugepage mappings for io, so handle that */
+ if (hugepage_shift) {
+ pa <<= hugepage_shift; <= This is wrong
+ pa |= token & ((1ul << hugepage_shift) - 1);
+ }
This patch fixes the virt -> phys translation in eeh_token_to_phys()
function.
$ cat /sys/kernel/debug/powerpc/eeh_address_cache
mem addr range [0x0000040080000000-0x00000400807fffff]: 0030:01:00.1
mem addr range [0x0000040080800000-0x0000040080ffffff]: 0030:01:00.1
mem addr range [0x0000040081000000-0x00000400817fffff]: 0030:01:00.0
mem addr range [0x0000040081800000-0x0000040081ffffff]: 0030:01:00.0
mem addr range [0x0000040082000000-0x000004008207ffff]: 0030:01:00.1
mem addr range [0x0000040082080000-0x00000400820fffff]: 0030:01:00.0
mem addr range [0x0000040082100000-0x000004008210ffff]: 0030:01:00.1
mem addr range [0x0000040082110000-0x000004008211ffff]: 0030:01:00.0
Above is the list of cached io address ranges of pci 0030:01:00.<fn>.
Before this patch:
Tracing 'arg1' of function eeh_addr_cache_get_dev() during error injection
clearly shows that 'addr=' contains wrong physical address:
KASAN report a slab-out-of-bounds problem. The logs are listed below.
It is because in function jffs2_scan_dirent_node, we alloc "checkedlen+1"
bytes for fd->name and we check crc with length rd->nsize. If checkedlen
is less than rd->nsize, it will cause the slab-out-of-bounds problem.
jffs2: Dirent at *** has zeroes in name. Truncating to %d char
==================================================================
BUG: KASAN: slab-out-of-bounds in crc32_le+0x1ce/0x260 at addr ffff8800842cf2d1
Read of size 1 by task test_JFFS2/915
=============================================================================
BUG kmalloc-64 (Tainted: G B O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in jffs2_alloc_full_dirent+0x2a/0x40 age=0 cpu=1 pid=915
___slab_alloc+0x580/0x5f0
__slab_alloc.isra.24+0x4e/0x64
__kmalloc+0x170/0x300
jffs2_alloc_full_dirent+0x2a/0x40
jffs2_scan_eraseblock+0x1ca4/0x3b64
jffs2_scan_medium+0x285/0xfe0
jffs2_do_mount_fs+0x5fb/0x1bbc
jffs2_do_fill_super+0x245/0x6f0
jffs2_fill_super+0x287/0x2e0
mount_mtd_aux.isra.0+0x9a/0x144
mount_mtd+0x222/0x2f0
jffs2_mount+0x41/0x60
mount_fs+0x63/0x230
vfs_kern_mount.part.6+0x6c/0x1f4
do_mount+0xae8/0x1940
SyS_mount+0x105/0x1d0
INFO: Freed in jffs2_free_full_dirent+0x22/0x40 age=27 cpu=1 pid=915
__slab_free+0x372/0x4e4
kfree+0x1d4/0x20c
jffs2_free_full_dirent+0x22/0x40
jffs2_build_remove_unlinked_inode+0x17a/0x1e4
jffs2_do_mount_fs+0x1646/0x1bbc
jffs2_do_fill_super+0x245/0x6f0
jffs2_fill_super+0x287/0x2e0
mount_mtd_aux.isra.0+0x9a/0x144
mount_mtd+0x222/0x2f0
jffs2_mount+0x41/0x60
mount_fs+0x63/0x230
vfs_kern_mount.part.6+0x6c/0x1f4
do_mount+0xae8/0x1940
SyS_mount+0x105/0x1d0
entry_SYSCALL_64_fastpath+0x1e/0x97
Call Trace:
[<ffffffff815befef>] dump_stack+0x59/0x7e
[<ffffffff812d1d65>] print_trailer+0x125/0x1b0
[<ffffffff812d82c8>] object_err+0x34/0x40
[<ffffffff812dadef>] kasan_report.part.1+0x21f/0x534
[<ffffffff81132401>] ? vprintk+0x2d/0x40
[<ffffffff815f1ee2>] ? crc32_le+0x1ce/0x260
[<ffffffff812db41a>] kasan_report+0x26/0x30
[<ffffffff812d9fc1>] __asan_load1+0x3d/0x50
[<ffffffff815f1ee2>] crc32_le+0x1ce/0x260
[<ffffffff814764ae>] ? jffs2_alloc_full_dirent+0x2a/0x40
[<ffffffff81485cec>] jffs2_scan_eraseblock+0x1d0c/0x3b64
[<ffffffff81488813>] ? jffs2_scan_medium+0xccf/0xfe0
[<ffffffff81483fe0>] ? jffs2_scan_make_ino_cache+0x14c/0x14c
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff812d5d90>] ? kmem_cache_alloc_trace+0x10c/0x2cc
[<ffffffff818169fb>] ? mtd_point+0xf7/0x130
[<ffffffff81487dc9>] jffs2_scan_medium+0x285/0xfe0
[<ffffffff81487b44>] ? jffs2_scan_eraseblock+0x3b64/0x3b64
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff812d57df>] ? __kmalloc+0x12b/0x300
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff814a2753>] ? jffs2_sum_init+0x9f/0x240
[<ffffffff8148b2ff>] jffs2_do_mount_fs+0x5fb/0x1bbc
[<ffffffff8148ad04>] ? jffs2_del_noinode_dirent+0x640/0x640
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff81127c5b>] ? __init_rwsem+0x97/0xac
[<ffffffff81492349>] jffs2_do_fill_super+0x245/0x6f0
[<ffffffff81493c5b>] jffs2_fill_super+0x287/0x2e0
[<ffffffff814939d4>] ? jffs2_parse_options+0x594/0x594
[<ffffffff81819bea>] mount_mtd_aux.isra.0+0x9a/0x144
[<ffffffff81819eb6>] mount_mtd+0x222/0x2f0
[<ffffffff814939d4>] ? jffs2_parse_options+0x594/0x594
[<ffffffff81819c94>] ? mount_mtd_aux.isra.0+0x144/0x144
[<ffffffff81258757>] ? free_pages+0x13/0x1c
[<ffffffff814fa0ac>] ? selinux_sb_copy_data+0x278/0x2e0
[<ffffffff81492b35>] jffs2_mount+0x41/0x60
[<ffffffff81302fb7>] mount_fs+0x63/0x230
[<ffffffff8133755f>] ? alloc_vfsmnt+0x32f/0x3b0
[<ffffffff81337f2c>] vfs_kern_mount.part.6+0x6c/0x1f4
[<ffffffff8133ceec>] do_mount+0xae8/0x1940
[<ffffffff811b94e0>] ? audit_filter_rules.constprop.6+0x1d10/0x1d10
[<ffffffff8133c404>] ? copy_mount_string+0x40/0x40
[<ffffffff812cbf78>] ? alloc_pages_current+0xa4/0x1bc
[<ffffffff81253a89>] ? __get_free_pages+0x25/0x50
[<ffffffff81338993>] ? copy_mount_options.part.17+0x183/0x264
[<ffffffff8133e3a9>] SyS_mount+0x105/0x1d0
[<ffffffff8133e2a4>] ? copy_mnt_ns+0x560/0x560
[<ffffffff810e8391>] ? msa_space_switch_handler+0x13d/0x190
[<ffffffff81be184a>] entry_SYSCALL_64_fastpath+0x1e/0x97
[<ffffffff810e9274>] ? msa_space_switch+0xb0/0xe0
Memory state around the buggy address: ffff8800842cf180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8800842cf200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8800842cf280: fc fc fc fc fc fc 00 00 00 00 01 fc fc fc fc fc
^ ffff8800842cf300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8800842cf380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
the pointer to struct dst_entry is used as pointer to struct rtable: this
turns the access to struct members like rt_mtu_locked into an OOB read in
the stack. Fix this changing the temporary variable used for IPv4 packets
in ovs_fragment(), similarly to what is done for IPv6 few lines below.
Fixes: d52e5a7e7ca4 ("ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmt") Cc: <stable@vger.kernel.org> Acked-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arm64 assembler in binutils 2.32 and above generates a program
property note in a note section, .note.gnu.property, to encode used x86
ISAs and features. But the kernel linker script only contains a single
NOTE segment:
In snd_sb_qsound_build, snd_ctl_add(..,p->qsound_switch...) and
snd_ctl_add(..,p->qsound_space..) are called. But the second
arguments of snd_ctl_add() could be freed via snd_ctl_add_replace()
->snd_ctl_free_one(). After the error code is returned,
snd_sb_qsound_destroy(p) is called in __error branch.
But in snd_sb_qsound_destroy(), the freed p->qsound_switch and
p->qsound_space are still used by snd_ctl_remove().
My patch set p->qsound_switch and p->qsound_space to NULL if
snd_ctl_add() failed to avoid the uaf bugs. But these codes need
to further be improved with the code style.
In snd_emu8000_create_mixer, the callee snd_ctl_add(..,emu->controls[i])
calls snd_ctl_add_replace(.., kcontrol,..). Inside snd_ctl_add_replace(),
if error happens, kcontrol will be freed by snd_ctl_free_one(kcontrol).
Then emu->controls[i] points to a freed memory, and the execution comes
to __error branch of snd_emu8000_create_mixer. The freed emu->controls[i]
is used in snd_ctl_remove(card, emu->controls[i]).
My patch set emu->controls[i] to NULL if snd_ctl_add() failed to avoid
the uaf.
Since the 'mfs' member has been declared as 'u32' in include/scsi/libfc.h,
use the %u format specifier instead of %hu. This patch fixes the following
clang compiler warning:
warning: format specifies type
'unsigned short' but the argument has type 'u32' (aka 'unsigned int')
[-Wformat]
"lport->mfs:%hu\n", mfs, lport->mfs);
~~~ ^~~~~~~~~~
%u
Link: https://lore.kernel.org/r/20210415220826.29438-8-bvanassche@acm.org Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a crash caused by a double put on the node when the driver completed an
ACC for an unsolicted abort on the same node. The second put was executed
by lpfc_nlp_not_used() and is wrong because the completion routine executes
the nlp_put when the iocbq was released. Additionally, the driver is
issuing a LOGO then immediately calls lpfc_nlp_set_state to put the node
into NPR. This call does nothing.
Remove the lpfc_nlp_not_used call and additional set_state in the
completion routine. Remove the lpfc_nlp_set_state post issue_logo. Isn't
necessary.
Link: https://lore.kernel.org/r/20210412013127.2387-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For two of the supported sensors the stv06xx driver allocates memory which
is stored in sd->sensor_priv. This memory is freed on a disconnect, but if
the probe() fails, then it isn't freed and so this leaks memory.
Add a new probe_error() op that drivers can use to free any allocated
memory in case there was a probe failure.
Thanks to Pavel Skripkin <paskripkin@gmail.com> for discovering the cause
of the memory leak.
In case of error in dvb_usb_adapter_dvb_init() or
dvb_usb_adapter_dvb_init() d->num_adapters_initialized won't be
incremented, but dvb_usb_adapter_exit() relies on it:
for (n = 0; n < d->num_adapters_initialized; n++)
So, allocated objects won't be freed.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reported-by: syzbot+3c2be7424cea3b932b0e@syzkaller.appspotmail.com Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If some error occurs, URB buffers should also be freed. If they aren't
freed with the dvb here, the em28xx_dvb_fini call doesn't frees the URB
buffers as dvb is set to NULL. The function in which error occurs should
do all the cleanup for the allocations it had done.
Tested the patch with the reproducer provided by syzbot. This patch
fixes the memleak.
Reported-by: syzbot+889397c820fa56adf25d@syzkaller.appspotmail.com Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a fix for the memory leak bugs that can occur when the
saa7164_encoder_register() function fails.
The function allocates memory without explicitly freeing
it when errors occur.
Add a better error handling that deallocate the unused buffers before the
function exits during a fail.
Signed-off-by: Daniel Niv <danielniv3@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a compilation warning in pscsi_complete_cmd():
drivers/target/target_core_pscsi.c: In function ‘pscsi_complete_cmd’:
drivers/target/target_core_pscsi.c:624:5: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
; /* XXX: TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE */
Link: https://lore.kernel.org/r/20210228055645.22253-5-chaitanya.kulkarni@wdc.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
When cross-compiling with Clang, the `$(CLANG_FLAGS)' variable
contains additional flags needed to build C and assembly sources
for the target platform. Normally this variable is automatically
included in `$(KBUILD_CFLAGS)' via the top-level Makefile.
The x86 real-mode makefile builds `$(REALMODE_CFLAGS)' from a
plain assignment and therefore drops the Clang flags. This causes
Clang to not recognize x86-specific assembler directives:
Explicit propagation of `$(CLANG_FLAGS)' to `$(REALMODE_CFLAGS)',
which is inherited by real-mode make rules, fixes cross-compilation
with Clang for x86 targets.
Relevant flags:
* `--target' sets the target architecture when cross-compiling. This
flag must be set for both compilation and assembly (`KBUILD_AFLAGS')
to support architecture-specific assembler directives.
* `-no-integrated-as' tells clang to assemble with GNU Assembler
instead of its built-in LLVM assembler. This flag is set by default
unless `LLVM_IAS=1' is set, because the LLVM assembler can't yet
parse certain GNU extensions.
It should not be necessary to update the current_state field of
struct pci_dev in pci_enable_device_flags() before calling
do_pci_enable_device() for the device, because none of the
code between that point and the pci_set_power_state() call in
do_pci_enable_device() invoked later depends on it.
Moreover, doing that is actively harmful in some cases. For example,
if the given PCI device depends on an ACPI power resource whose _STA
method initially returns 0 ("off"), but the config space of the PCI
device is accessible and the power state retrieved from the
PCI_PM_CTRL register is D0, the current_state field in the struct
pci_dev representing that device will get out of sync with the
power.state of its ACPI companion object and that will lead to
power management issues going forward.
To avoid such issues it is better to leave the current_state value
as is until it is changed to PCI_D0 by do_pci_enable_device() as
appropriate. However, the power state of the device is not changed
to PCI_D0 if it is already enabled when pci_enable_device_flags()
gets called for it, so update its current_state in that case, but
use pci_update_current_state() covering platform PM too for that.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/ Reported-by: Maximilian Luz <luzmaximilian@gmail.com> Tested-by: Maximilian Luz <luzmaximilian@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch adds extra checking for bInterval passed by configfs.
The 5.6.4 chapter of USB Specification (rev. 2.0) say:
"A high-bandwidth endpoint must specify a period of 1x125 µs
(i.e., a bInterval value of 1)."
The issue was observed during testing UVC class on CV.
I treat this change as improvement because we can control
bInterval by configfs.
Use kzalloc() rather than kmalloc() for the dynamically allocated parts
of the colormap in fb_alloc_cmap_gfp, to prevent a leak of random kernel
data to userspace under certain circumstances.
Some of SD cards sets permanent write protection bit in their CSD register,
due to lifespan or internal problem. To avoid unnecessary I/O write
operations, let's parse the bits in the CSD during initialization and mark
the card as read only for this case.
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
When mounting eCryptfs, a null "dev_name" argument to ecryptfs_mount()
causes a kernel panic if the parsed options are valid. The easiest way to
reproduce this is to call mount() from userspace with an existing
eCryptfs mount's options and a "source" argument of 0.
Error out if "dev_name" is null in ecryptfs_mount()
In cm_write(), if the 'buf' is allocated memory but not fully consumed,
it is possible to reallocate the buffer without freeing it by passing
'*ppos' as 0 on a subsequent call.
Add an explicit kfree() before kzalloc() to prevent the possible memory
leak.
Fixes: 526b4af47f44 ("ACPI: Split out custom_method functionality into an own driver") Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com> Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cm_write(), buf is always freed when reaching the end of the
function. If the requested count is less than table.length, the
allocated buffer will be freed but subsequent calls to cm_write() will
still try to access it.
Remove the unconditional kfree(buf) at the end of the function and
set the buf to NULL in the -EINVAL error path to match the rest of
function.
Fixes: 03d1571d9513 ("ACPI: custom_method: fix memory leaks") Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com> Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
addr 001fff800ad5f970 is located in stack of task test_progs/853 at
offset 96 in frame:
print_fn_code+0x0/0x380
this frame has 1 object:
[32, 96) 'buffer'
Memory state around the buggy address: 001fff800ad5f800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 001fff800ad5f880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>001fff800ad5f900: 00 00 f1 f1 f1 f1 00 00 00 00 00 00 00 00 f3 f3
^ 001fff800ad5f980: f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 00 00 001fff800ad5fa00: 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 00 00
On recent Thinkpad platforms it was reported that temp sensor 11 was
always incorrectly displaying 66C. It turns out the reason for this is
that this location in EC RAM is not a temperature sensor but is the
power supply ID (offset 0xC2).
Based on feedback from the Lenovo firmware team the EC RAM version can
be determined and for the current version (3) only the 0x78 to 0x7F
range is used for temp sensors. I don't have any details for earlier
versions so I have left the implementation unaltered there.
Note - in this block only 0x78 and 0x79 are officially designated (CPU &
GPU sensors). The use of the other locations in the block will vary from
platform to platform; but the existing logic to detect a sensor presence
holds.
Signed-off-by: Mark Pearson <markpearson@lenovo.com> Link: https://lore.kernel.org/r/20210407212015.298222-1-markpearson@lenovo.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Use memset to initialize local array in drivers/net/usb/ax88179_178a.c, and
also set a local u16 and u32 variable to 0. Fixes a KMSAN found uninit-value bug
reported by syzbot at:
https://syzkaller.appspot.com/bug?id=00371c73c72f72487c1d0bfe0cc9d00de339d5aa
Reported-by: syzbot+4993e4a0e237f1b53747@syzkaller.appspotmail.com Signed-off-by: Phillip Potter <phil@philpotter.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timerfd gives processes a way to set wake alarms, but unlike timers made using
timer_create, timerfds don't check whether the process has CAP_WAKE_ALARM
before setting alarm-time timers. CAP_WAKE_ALARM is supposed to gate this
behavior and so it makes sense that we should deny permission to create such
timerfds if the process doesn't have this capability.
Commit 8a12f8836145 ("net: hso: fix null-ptr-deref during tty device
unregistration") fixed the racy minor allocation reported by syzbot, but
introduced an unconditional NULL-pointer dereference on every disconnect
instead.
Specifically, the serial device table must no longer be accessed after
the minor has been released by hso_serial_tty_unregister().
Fixes: 8a12f8836145 ("net: hso: fix null-ptr-deref during tty device unregistration") Cc: stable@vger.kernel.org Cc: Anirudh Rayabharam <mail@anirudhrb.com> Reported-by: Leonardo Antoniazzi <leoanto@aruba.it> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Anirudh Rayabharam <mail@anirudhrb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit in Fixes: added support for kexec-ing a kernel on panic using a
new system call. As part of it, it does prepare a memory map for the new
kernel.
However, while doing so, it wrongly accesses memory it has not
allocated: it accesses the first element of the cmem->ranges[] array in
memmap_exclude_ranges() but it has not allocated the memory for it in
crash_setup_memmap_entries(). As KASAN reports:
BUG: KASAN: vmalloc-out-of-bounds in crash_setup_memmap_entries+0x17e/0x3a0
Write of size 8 at addr ffffc90000426008 by task kexec/1187
(gdb) list *crash_setup_memmap_entries+0x17e
0xffffffff8107cafe is in crash_setup_memmap_entries (arch/x86/kernel/crash.c:322).
317 unsigned long long mend)
318 {
319 unsigned long start, end;
320
321 cmem->ranges[0].start = mstart;
322 cmem->ranges[0].end = mend;
323 cmem->nr_ranges = 1;
324
325 /* Exclude elf header region */
326 start = image->arch.elf_load_addr;
(gdb)
Make sure the ranges array becomes a single element allocated.
[ bp: Write a proper commit message. ]
Fixes: dd5f726076cc ("kexec: support for kexec on panic using new system call") Signed-off-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/725fa3dc1da2737f0f6188a1a9701bead257ea9d.camel@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds wrappers for the __builtin overflow checkers present in gcc
5.1+ as well as fallback implementations for earlier compilers. It's not
that easy to implement the fully generic __builtin_X_overflow(T1 a, T2
b, T3 *d) in macros, so the fallback code assumes that T1, T2 and T3 are
the same. We obviously don't want the wrappers to have different
semantics depending on $GCC_VERSION, so we also insist on that even when
using the builtins.
There are a few problems with the 'a+b < a' idiom for checking for
overflow: For signed types, it relies on undefined behaviour and is
not actually complete (it doesn't check underflow;
e.g. INT_MIN+INT_MIN == 0 isn't caught). Due to type promotion it
is wrong for all types (signed and unsigned) narrower than
int. Similarly, when a and b does not have the same type, there are
subtle cases like
u32 a;
if (a + sizeof(foo) < a)
return -EOVERFLOW;
a += sizeof(foo);
where the test is always false on 64 bit platforms. Add to that that it
is not always possible to determine the types involved at a glance.
The new overflow.h is somewhat bulky, but that's mostly a result of
trying to be type-generic, complete (e.g. catching not only overflow
but also signed underflow) and not relying on undefined behaviour.
Linus is of course right [1] that for unsigned subtraction a-b, the
right way to check for overflow (underflow) is "b > a" and not
"__builtin_sub_overflow(a, b, &d)", but that's just one out of six cases
covered here, and included mostly for completeness.
So is it worth it? I think it is, if nothing else for the documentation
value of seeing
if (check_add_overflow(a, b, &d))
return -EGOAWAY;
do_stuff_with(d);
instead of the open-coded (and possibly wrong and/or incomplete and/or
UBsan-tickling)
if (a+b < a)
return -EGOAWAY;
do_stuff_with(a+b);
While gcc does recognize the 'a+b < a' idiom for testing unsigned add
overflow, it doesn't do nearly as good for unsigned multiplication
(there's also no single well-established idiom). So using
check_mul_overflow in kcalloc and friends may also make gcc generate
slightly better code.
The ia64_mf() macro defined in tools/arch/ia64/include/asm/barrier.h is
already defined in <asm/gcc_intrin.h> on ia64 which causes libbpf
failing to build:
CC /usr/src/linux/tools/bpf/bpftool//libbpf/staticobjs/libbpf.o
In file included from /usr/src/linux/tools/include/asm/barrier.h:24,
from /usr/src/linux/tools/include/linux/ring_buffer.h:4,
from libbpf.c:37:
/usr/src/linux/tools/include/asm/../../arch/ia64/include/asm/barrier.h:43: error: "ia64_mf" redefined [-Werror]
43 | #define ia64_mf() asm volatile ("mf" ::: "memory")
|
In file included from /usr/include/ia64-linux-gnu/asm/intrinsics.h:20,
from /usr/include/ia64-linux-gnu/asm/swab.h:11,
from /usr/include/linux/swab.h:8,
from /usr/include/linux/byteorder/little_endian.h:13,
from /usr/include/ia64-linux-gnu/asm/byteorder.h:5,
from /usr/src/linux/tools/include/uapi/linux/perf_event.h:20,
from libbpf.c:36:
/usr/include/ia64-linux-gnu/asm/gcc_intrin.h:382: note: this is the location of the previous definition
382 | #define ia64_mf() __asm__ volatile ("mf" ::: "memory")
|
cc1: all warnings being treated as errors
Thus, remove the definition from tools/arch/ia64/include/asm/barrier.h.
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_SPARSEMEM=y and CONFIG_MEMORY_HOTPLUG=y, the functions
computer_pernodesize() and scatter_node_data() should not be marked as
__meminit because they are needed after init, on any memory hotplug
event. Also, early_nr_cpus_node() is called by compute_pernodesize(),
so early_nr_cpus_node() cannot be __meminit either.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1612): Section mismatch in reference from the function arch_alloc_nodedata() to the function .meminit.text:compute_pernodesize()
The function arch_alloc_nodedata() references the function __meminit compute_pernodesize().
This is often because arch_alloc_nodedata lacks a __meminit annotation or the annotation of compute_pernodesize is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1692): Section mismatch in reference from the function arch_refresh_nodedata() to the function .meminit.text:scatter_node_data()
The function arch_refresh_nodedata() references the function __meminit scatter_node_data().
This is often because arch_refresh_nodedata lacks a __meminit annotation or the annotation of scatter_node_data is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1502): Section mismatch in reference from the function compute_pernodesize() to the function .meminit.text:early_nr_cpus_node()
The function compute_pernodesize() references the function __meminit early_nr_cpus_node().
This is often because compute_pernodesize lacks a __meminit annotation or the annotation of early_nr_cpus_node is wrong.
Link: https://lkml.kernel.org/r/20210411001201.3069-1-rdunlap@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Mike Rapoport <rppt@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic in connect() is currently written with the assumption that
xenbus_watch_pathfmt() will return an error for a node that does not
exist. This assumption is incorrect: xenstore does allow a watch to
be registered for a nonexistent node (and will send notifications
should the node be subsequently created).
As of commit 1f2565780 ("xen-netback: remove 'hotplug-status' once it
has served its purpose"), this leads to a failure when a domU
transitions into XenbusStateConnected more than once. On the first
domU transition into Connected state, the "hotplug-status" node will
be deleted by the hotplug_status_changed() callback in dom0. On the
second or subsequent domU transition into Connected state, the
hotplug_status_changed() callback will therefore never be invoked, and
so the backend will remain stuck in InitWait.
This failure prevents scenarios such as reloading the xen-netfront
module within a domU, or booting a domU via iPXE. There is
unfortunately no way for the domU to work around this dom0 bug.
Fix by explicitly checking for existence of the "hotplug-status" node,
thereby creating the behaviour that was previously assumed to exist.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently psw_idle does not allocate a stack frame and does not
save its r14 and r15 into the save area. Even though this is valid from
call ABI point of view, because psw_idle does not make any calls
explicitly, in reality psw_idle is an entry point for controlled
transition into serving interrupts. So, in practice, psw_idle stack
frame is analyzed during stack unwinding. Depending on build options
that r14 slot in the save area of psw_idle might either contain a value
saved by previous sibling call or complete garbage.
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped
around with commit 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for
drivers that existed in v4.4").
Let's fix the issue with aliases as discussed on the mailing lists. While
the mmc aliases should be board specific, let's first fix the issue with
minimal changes.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhang Yi [Fri, 23 Apr 2021 12:35:07 +0000 (20:35 +0800)]
ext4: correct error label in ext4_rename()
The backport of upstream patch 5dccdc5a1916 ("ext4: do not iput inode
under running transaction in ext4_rename()") introduced a regression on
the stable kernels 4.14 and older. One of the end_rename error label was
forgetting to change to release_bh, which may trigger below bug.
Fixes: 2fc8ce56985d ("ext4: do not iput inode under running transaction in ext4_rename()") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Since uprobes is not supported for thumb, check that the thumb bit is
not set when matching the uprobes instruction hooks.
The Arm UDF instructions used for uprobes triggering
(UPROBE_SWBP_ARM_INSN and UPROBE_SS_ARM_INSN) coincidentally share the
same encoding as a pair of unallocated 32-bit thumb instructions (not
UDF) when the condition code is 0b1111 (0xf). This in effect makes it
possible to trigger the uprobes functionality from thumb, and at that
using two unallocated instructions which are not permanently undefined.
Signed-off-by: Fredrik Strupe <fredrik@strupe.net> Cc: stable@vger.kernel.org Fixes: c7edc9e326d5 ("ARM: add uprobes support") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
When the probe fails, we must disable the regulator that was previously
enabled.
This patch is a follow-up to commit ac88c531a5b3
("net: davicom: Fix regulator not turned off on failed probe") which missed
one case.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the cache_type for the SCSI device is changed, the SCSI layer issues a
MODE_SELECT command. The caching mode details are communicated via a
request buffer associated with the SCSI command with data direction set as
DMA_TO_DEVICE (scsi_mode_select()). When this command reaches the libata
layer, as a part of generic initial setup, libata layer sets up the
scatterlist for the command using the SCSI command (ata_scsi_qc_new()).
This command is then translated by the libata layer into
ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat()). The libata layer treats
this as a non-data command (ata_mselect_caching()), since it only needs an
ATA taskfile to pass the caching on/off information to the device. It does
not need the scatterlist that has been setup, so it does not perform
dma_map_sg() on the scatterlist (ata_qc_issue()). Unfortunately, when this
command reaches the libsas layer (sas_ata_qc_issue()), libsas layer sees it
as a non-data command with a scatterlist. It cannot extract the correct DMA
length since the scatterlist has not been mapped with dma_map_sg() for a
DMA operation. When this partially constructed SAS task reaches pm80xx
LLDD, it results in the following warning:
"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"
Update libsas to handle ATA non-data commands separately so num_scatter and
total_xfer_len remain 0.
Link: https://lore.kernel.org/r/20210318225632.2481291-1-jollys@google.com Fixes: 53de092f47ff ("scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA") Tested-by: Luo Jiaxing <luojiaxing@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jolly Shah <jollys@google.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Zenbook Flip entry that was added overwrites a previous one
because of a typo:
In file included from drivers/input/serio/i8042.h:23,
from drivers/input/serio/i8042.c:131:
drivers/input/serio/i8042-x86ia64io.h:591:28: error: initialized field overwritten [-Werror=override-init]
591 | .matches = {
| ^
drivers/input/serio/i8042-x86ia64io.h:591:28: note: (near initialization for 'i8042_dmi_noselftest_table[0].matches')
Add the missing separator between the two.
Fixes: b5d6e7ab7fe7 ("Input: i8042 - add ASUS Zenbook Flip to noselftest list") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Marcos Paulo de Souza <mpdesouza@suse.com> Link: https://lore.kernel.org/r/20210323130623.2302402-1-arnd@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
This patch forbids to add llsec seclevel for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
projects / thirdparty / kernel / stable.git / log
