Apurva Nandan [Fri, 11 Aug 2023 19:20:28 +0000 (00:50 +0530)]
arm64: dts: ti: k3-j784s4: Add phase tags marking
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to cover U-Boot challenges with DT.
That's why add it also to Linux to be aligned with bootloader requirement.
On TI K3 J784S4 SoC, only secure_proxy_mcu and secure_proxy_sa3 nodes are
exclusively used by R5 bootloader, rest of the dts nodes with bootph-* are
used by later boot stages also.
And secure_proxy_mcu and secure_proxy_sa3 are disabled in kernel device
tree, and will be only enabled in R5 bootloader device tree.
So, bootph-pre-ram for secure_proxy_mcu and secure_proxy_sa3 will be
added in R5 bootloader device tree only.
Add bootph-all for all other nodes that are used in the bootloader on
K3 J784S4 SoC, and bootph-pre-ram is not needed specifically for any node
in kernel dts.
Nishanth Menon [Wed, 9 Aug 2023 08:45:58 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am625-beagleplay: Add HDMI support
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (ITE-IT66121) on the BeaglePlay platform. For audio output,
BeaglePlay uses mcasp1.
Add pinmux info for DSS DPI signals.
Further, add support for HDMI audio and video output.
Aradhya Bhatia [Wed, 9 Aug 2023 08:45:56 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am62x-sk-common: Add HDMI support
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux info for DSS DPI output.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the AM625 SK and AM62-LP SK platforms.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Aradhya Bhatia [Wed, 9 Aug 2023 08:45:55 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am62-main: Add node for DSS
Add Display SubSystem (DSS) DT node for the AM625 SoC.
The DSS supports one each of video pipeline (vid) and video-lite
pipeline (vidl1). It outputs OLDI signals on one video port (VP1) and
DPI signals on another (VP2). The video ports are connected to the
pipelines via 2 identical overlay managers (ovr1 and ovr2).
Also add the DT node for DSS clock divider. This is a fixed-factor-clock
and does not have any register. This comes into effect whenenver OLDI
display is used. The input to this divider is a serial clock used by
OLDI TXes. The divider divides the input clock by 7, and provides the
pixel clock to VP1.
Aradhya Bhatia [Wed, 9 Aug 2023 08:45:54 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am62x-sk-common: Update main-i2c1 frequency
The Display Data Channel (DDC) transactions between an HDMI transmitter
(SIL9022A in this case) and an HDMI monitor, occur at a maximum of
100KHz. That's the maximum supported frequency within DDC standards.
While the SIL9022A can transact with the core at 400KHz, it needs to
drop the frequency to 100KHz when communicating with the monitor,
otherwise, the i2c controller times out and shows warning like this.
[ 985.773431] omap_i2c 20010000.i2c: controller timed out
That feature, however, has not been enabled in the SIL9022 driver.
Since, dropping the frequency doesn't affect any other devices on the
bus, drop the main-i2c1 frequency from 400KHz to 100KHz.
Andrew Davis [Wed, 9 Aug 2023 18:01:45 +0000 (13:01 -0500)]
arm64: dts: ti: k3-j721e: Enable C6x DSP nodes at the board level
C6x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.
As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.
Disable the C6x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.
Andrew Davis [Wed, 9 Aug 2023 18:01:44 +0000 (13:01 -0500)]
arm64: dts: ti: k3-j784s4: Enable C7x DSP nodes at the board level
C7x DSP nodes defined in the top-level J784s4 SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.
As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.
Disable the C7x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.
Andrew Davis [Wed, 9 Aug 2023 18:01:43 +0000 (13:01 -0500)]
arm64: dts: ti: k3-j721e: Enable C7x DSP nodes at the board level
C7x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.
As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.
Disable the C7x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:14 +0000 (19:38 -0500)]
arm64: dts: ti: k3-am64: Enable TSCADC nodes at the board level
TSCADC nodes defined in the top-level AM64 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and/or
device information.
Disable the TSCADC nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:13 +0000 (19:38 -0500)]
arm64: dts: ti: k3-am65: Enable TSCADC nodes at the board level
TSCADC nodes defined in the top-level AM65 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and/or
device information.
Disable the TSCADC nodes in the top-level dtsi files and only enable the
ones that are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:12 +0000 (19:38 -0500)]
arm64: dts: ti: k3-j721e: Enable TSCADC nodes at the board level
TSCADC nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and/or
device information.
Disable the TSCADC nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:11 +0000 (19:38 -0500)]
arm64: dts: ti: k3-j7200: Enable GPIO nodes at the board level
GPIO nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
Disable the GPIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:10 +0000 (19:38 -0500)]
arm64: dts: ti: k3-j721s2: Enable GPIO nodes at the board level
GPIO nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
Disable the GPIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:09 +0000 (19:38 -0500)]
arm64: dts: ti: k3-j721e: Enable GPIO nodes at the board level
GPIO nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
Disable the GPIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:08 +0000 (19:38 -0500)]
arm64: dts: ti: k3-am64: Enable OSPI nodes at the board level
OSPI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:07 +0000 (19:38 -0500)]
arm64: dts: ti: k3-j7200: Enable OSPI nodes at the board level
OSPI nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:06 +0000 (19:38 -0500)]
arm64: dts: ti: k3-j721e: Enable OSPI nodes at the board level
OSPI nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Andrew Davis [Thu, 10 Aug 2023 00:38:05 +0000 (19:38 -0500)]
arm64: dts: ti: k3-am65: Enable OSPI nodes at the board level
OSPI nodes defined in the top-level AM65x SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
arm64: dts: ti: k3-j784s4: Fix interrupt ranges for wkup & main gpio
This patch fixes the interrupt range for wakeup and main domain gpio
interrupt routers. They were wrongly subtracted by 32 instead of
following what is defined in the interrupt map in the TRM (Table 9-35).
arm64: dts: ti: k3: Add cfg reg region to ringacc node
Add register range of ringacc cfg node to all k3 SoC dtsi files. This is
normally under Device Management firmware control but some entities like
bootloader have to access directly and thus required to be present in DT.
dt-bindings: soc: ti: k3-ringacc: Describe cfg reg region
RINGACC module on K3 SoCs have CFG register region which is usually
configured by a Device Management firmware. But certain entities such as
bootloader (like U-Boot) may have to access them directly. Describe this
region in the binding documentation for completeness of module
description.
Keep the binding compatible with existing DTS files by requiring first
four regions to be present at least.
Udit Kumar [Wed, 9 Aug 2023 05:01:08 +0000 (10:31 +0530)]
arm64: dts: ti: k3-j784s4-evm: Correct Pin mux offset for ADC
After splitting wkup_pmx pin mux for J784S4 into four regions.
Pin mux offset for ADC nodes were not updated to align with new
regions, due to this while probing ADC driver out of range
error was seen.
Pin mux offsets for ADC nodes are corrected in this patch.
Udit Kumar [Wed, 2 Aug 2023 11:41:26 +0000 (17:11 +0530)]
arm64: dts: ti: k3-j784s4-evm: Correct Pin mux offset for ospi
After splitting wkup_pmx pin mux for J784S4 into four regions.
Pin mux offset for OSPI nodes were not updated to align with new
regions, due to this while setting ospi pin muxes out of range
error was seen.
Pin mux offsets for OSPI nodes are corrected in this patch.
Andrew Davis [Wed, 2 Aug 2023 17:45:20 +0000 (12:45 -0500)]
arm64: dts: ti: k3-am64: Merge the two main_conf nodes
There are two nodes representing the same register space, this looks to
have been created by some merge or copy/paste error. Remove the second
instance of this node and move its children into the first instance.
Ravi Gunasekaran [Tue, 25 Jul 2023 10:36:51 +0000 (16:06 +0530)]
arm64: dts: ti: k3-am62a7-sk: Enable dual role support for Type-C port
USB0 is interfaced with a Type-C DRP connector and is managed via a
USB PD controller. Add support for the Type-C port with dual data
and power sink role.
arm64: dts: ti: k3-am64-tqma64xxl-mbax4xxl: add SD-card and WLAN overlays
As the SD-card and WLAN are connected to the same SDHC interface (with a
GPIO-controlled mux), they are mutually exclusive. Provide Device Tree
overlays for both configurations.
arm64: dts: ti: Add TQ-Systems TQMa64XxL SoM and MBaX4XxL carrier board Device Trees
The TQMa64XxL is an LGA SoM based on the TI AM64x SoC family. Add DTS(I)
for the AM642 (2x Cortex-A53) variant and its combination with our
MBaX4XxL carrier board.
arm64: dts: ti: k3-j721s2: Add overlay to enable main CPSW2G with GESI
The MAIN CPSW2G instance of CPSW on J721S2 SoC can be enabled with the GESI
Expansion Board connected to the J7 Common-Proc-Board. Use the overlay
to enable this.
Add alias for the MAIN CPSW2G port to enable kernel to fetch MAC address
directly from U-Boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com> Link: https://lore.kernel.org/r/20230726065407.378455-3-s-vadapalli@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
Sinthu Raja [Fri, 21 Jul 2023 08:21:50 +0000 (13:51 +0530)]
arm64: dts: ti: k3-j721s2-main: Add dts nodes for EHRPWMs
Add dts nodes for 6 EHRPWM instances on SoC. Disable EHRPWM nodes in the
dtsi files and only enable the ones that are actually pinned out on a
given board in the board dts file.
arm64: dts: ti: k3-j721s2: Add support for CAN instances 3 and 5 in main domain
CAN instances 3 and 5 in the main domain are brought on the common
processor board through header J27 and J28. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceivers on
the common processor board. Threfore, add respective mux, transceiver
dt nodes to add support for these CAN instances.
Introduce the debounce select mux macros to allow folks to setup
debounce configuration for pins. Each configuration selected maps
to a specific timing register as documented in appropriate Technical
Reference Manual (example:[1]).
dt-bindings: crypto: ti,sa2ul: make power-domains conditional
Devices specific to compatible ti,am62-sa3ul don't have control over
power of SA3UL from main domain.
"power-domains" property in crypto node tries to access
the SA3UL power, for which it gets NACK and hence, driver doesn't
probe properly for those particular devices.
Make "power-domains" property as false for devices with
compatible ti,am62-sa3ul.
dt-bindings: ti-serdes-mux: Deprecate header with constants
The constants to define the idle state of SERDES MUX were defined in
bindings header. They are used only in DTS and driver uses the dt property
to set the idle state making it unsuitable for bindings.
The constants are moved to header next to DTS ("arch/arm64/boot/dts/ti/")
and all the references to bindings header are removed.
So add a warning to mark this bindings header as deprecated.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Roger Quadros <rogerq@kernel.org> Acked-by: Peter Rosin <peda@axentia.se> Link: https://lore.kernel.org/r/20230721125732.122421-3-j-choudhary@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
arm64: dts: ti: Use local header for SERDES MUX idle-state values
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
Also add J784S4 SERDES4 lane definitions which were missed earlier.
arm64: dts: ti: Fix compatible of ti,*-ehrpwm-tbclk
TI EHRPWM compatible is just ti,*-ehrpwm-tbclk without needing a
syscon compatibility.
Fixes the following dtbs_check warnings:
compatible: [''ti,am654-ehrpwm-tbclk, 'syscon'] is too long
compatible: ['ti,am64-epwm-tbclk', 'syscon'] is too long
compatible: ['ti,am62-epwm-tbclk', 'syscon'] is too long
We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.
The answer is "No. No we cannot".
I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street. And at the yearly
maintainer summit, we will all sing the alphabet song together.
I doubt I will keep doing this. At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.
Repeats: 80e62bc8487b ("MAINTAINERS: re-sort all entries and fields") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- swiotlb area sizing fixes (Petr Tesarik)
* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: reduce the number of areas to match actual memory pool size
swiotlb: always set the number of areas before allocating the pool
Merge tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for the mechanism to park CPUs with an INIT IPI.
On shutdown or kexec, the kernel tries to park the non-boot CPUs with
an INIT IPI. But the same code path is also used by the crash utility.
If the CPU which panics is not the boot CPU then it sends an INIT IPI
to the boot CPU which resets the machine.
Prevent this by validating that the CPU which runs the stop mechanism
is the boot CPU. If not, leave the other CPUs in HLT"
* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Don't send INIT to boot CPU
Merge tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fixes for KVM
- fix for loongson build and cpu probing
- DT fixes
* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
MIPS: dts: add missing space before {
MIPS: Loongson: Fix build error when make modules_install
MIPS: KVM: Fix NULL pointer dereference
MIPS: Loongson: Fix cpu_probe_loongson() again
Merge tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix potential use after free in unmount
- minor cleanup
- add worker to cleanup stale directory leases
* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Add a laundromat thread for cached directories
smb: client: remove redundant pointer 'server'
cifs: fix session state transition to avoid use-after-free issue
Merge tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"16 hotfixes. Six are cc:stable and the remainder address post-6.4
issues"
The merge undoes the disabling of the CONFIG_PER_VMA_LOCK feature, since
it was all hopefully fixed in mainline.
* tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib: dhry: fix sleeping allocations inside non-preemptable section
kasan, slub: fix HW_TAGS zeroing with slub_debug
kasan: fix type cast in memory_is_poisoned_n
mailmap: add entries for Heiko Stuebner
mailmap: update manpage link
bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
MAINTAINERS: add linux-next info
mailmap: add Markus Schneider-Pargmann
writeback: account the number of pages written back
mm: call arch_swap_restore() from do_swap_page()
squashfs: fix cache race with migration
mm/hugetlb.c: fix a bug within a BUG(): inconsistent pte comparison
docs: update ocfs2-devel mailing list address
MAINTAINERS: update ocfs2-devel mailing list address
mm: disable CONFIG_PER_VMA_LOCK until its fixed
fork: lock VMAs of the parent process when forking
fork: lock VMAs of the parent process when forking
When forking a child process, the parent write-protects anonymous pages
and COW-shares them with the child being forked using copy_present_pte().
We must not take any concurrent page faults on the source vma's as they
are being processed, as we expect both the vma and the pte's behind it
to be stable. For example, the anon_vma_fork() expects the parents
vma->anon_vma to not change during the vma copy.
A concurrent page fault on a page newly marked read-only by the page
copy might trigger wp_page_copy() and a anon_vma_prepare(vma) on the
source vma, defeating the anon_vma_clone() that wasn't done because the
parent vma originally didn't have an anon_vma, but we now might end up
copying a pte entry for a page that has one.
Before the per-vma lock based changes, the mmap_lock guaranteed
exclusion with concurrent page faults. But now we need to do a
vma_start_write() to make sure no concurrent faults happen on this vma
while it is being processed.
This fix can potentially regress some fork-heavy workloads. Kernel
build time did not show noticeable regression on a 56-core machine while
a stress test mapping 10000 VMAs and forking 5000 times in a tight loop
shows ~5% regression. If such fork time regression is unacceptable,
disabling CONFIG_PER_VMA_LOCK should restore its performance. Further
optimizations are possible if this regression proves to be problematic.
mm: lock newly mapped VMA which can be modified after it becomes visible
mmap_region adds a newly created VMA into VMA tree and might modify it
afterwards before dropping the mmap_lock. This poses a problem for page
faults handled under per-VMA locks because they don't take the mmap_lock
and can stumble on this VMA while it's still being modified. Currently
this does not pose a problem since post-addition modifications are done
only for file-backed VMAs, which are not handled under per-VMA lock.
However, once support for handling file-backed page faults with per-VMA
locks is added, this will become a race.
Fix this by write-locking the VMA before inserting it into the VMA tree.
Other places where a new VMA is added into VMA tree do not modify it
after the insertion, so do not need the same locking.
With recent changes necessitating mmap_lock to be held for write while
expanding a stack, per-VMA locks should follow the same rules and be
write-locked to prevent page faults into the VMA being expanded. Add
the necessary locking.
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"A few late arriving patches that missed the initial pull request. It's
mostly bug fixes (the dt-bindings is a fix for the initial pull)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove unused function declaration
scsi: target: docs: Remove tcm_mod_builder.py
scsi: target: iblock: Quiet bool conversion warning with pr_preempt use
scsi: dt-bindings: ufs: qcom: Fix ICE phandle
scsi: core: Simplify scsi_cdl_check_cmd()
scsi: isci: Fix comment typo
scsi: smartpqi: Replace one-element arrays with flexible-array members
scsi: target: tcmu: Replace strlcpy() with strscpy()
scsi: ncr53c8xx: Replace strlcpy() with strscpy()
scsi: lpfc: Fix lpfc_name struct packing
Merge tag 'i2c-for-6.5-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- xiic patch should have been in the original pull but slipped through
- mpc patch fixes a build regression
- nomadik cleanup
* tag 'i2c-for-6.5-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mpc: Drop unused variable
i2c: nomadik: Remove a useless call in the remove function
i2c: xiic: Don't try to handle more interrupt events after error
Merge tag 'hardening-v6.5-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- Check for NULL bdev in LoadPin (Matthias Kaehlcke)
- Revert unwanted KUnit FORTIFY build default
- Fix 1-element array causing boot warnings with xhci-hub
* tag 'hardening-v6.5-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
usb: ch9: Replace bmSublinkSpeedAttr 1-element array with flexible array
Revert "fortify: Allow KUnit test to build without FORTIFY"
dm: verity-loadpin: Add NULL pointer check for 'bdev' parameter
The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com> Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
- Update AMD IBS event error message since it now support per-process
profiling but no priviledge filters.
$ sudo perf record -e ibs_op//k -C 0
Error:
AMD IBS doesn't support privilege filtering. Try again without
the privilege modifiers (like 'k') at the end.
- Add --output option to save the data to a file not to be interfered
by other debug messages.
Test:
- Fix event parsing test on ARM where there's no raw PMU nor supports
PERF_PMU_CAP_EXTENDED_HW_TYPE.
- Update the lock contention test case for CSV output.
- Fix a segfault in the daemon command test.
Vendor events (JSON):
- Add has_event() to check if the given event is available on system
at runtime. On Intel machines, some transaction events may not be
present when TSC extensions are disabled.
- Update Intel event metrics.
Misc:
- Sort symbols by name using an external array of pointers instead of
a rbtree node in the symbol. This will save 16-bytes or 24-bytes
per symbol whether the sorting is actually requested or not.
- Fix unwinding DWARF callstacks using libdw when --symfs option is
used"
* tag 'perf-tools-for-v6.5-2-2023-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools-next: (38 commits)
perf test: Fix event parsing test when PERF_PMU_CAP_EXTENDED_HW_TYPE isn't supported.
perf test: Fix event parsing test on Arm
perf evsel amd: Fix IBS error message
perf: unwind: Fix symfs with libdw
perf symbol: Fix uninitialized return value in symbols__find_by_name()
perf test: Test perf lock contention CSV output
perf lock contention: Add --output option
perf lock contention: Add -x option for CSV style output
perf lock: Remove stale comments
perf vendor events intel: Update tigerlake to 1.13
perf vendor events intel: Update skylakex to 1.31
perf vendor events intel: Update skylake to 57
perf vendor events intel: Update sapphirerapids to 1.14
perf vendor events intel: Update icelakex to 1.21
perf vendor events intel: Update icelake to 1.19
perf vendor events intel: Update cascadelakex to 1.19
perf vendor events intel: Update meteorlake to 1.03
perf vendor events intel: Add rocketlake events/metrics
perf vendor metrics intel: Make transaction metrics conditional
perf jevents: Support for has_event function
...
The tests that don't use expect_eq() macro to determine that a test
is failured must increment failed_tests explicitly.
- lib/bitmap: drop optimization of bitmap_{from,to}_arr64
bitmap_{from,to}_arr64() optimization is overly optimistic
on 32-bit LE architectures when it's wired to
bitmap_copy_clear_tail().
- nodemask: Drop duplicate check in for_each_node_mask()
As the return value type of first_node() became unsigned, the node
>= 0 became unnecessary.
- cpumask: fix function description kernel-doc notation
- MAINTAINERS: Add bits.h and bitfield.h to the BITMAP API record
Add linux/bits.h and linux/bitfield.h for visibility"
* tag 'bitmap-6.5-rc1' of https://github.com/norov/linux:
MAINTAINERS: Add bitfield.h to the BITMAP API record
MAINTAINERS: Add bits.h to the BITMAP API record
cpumask: fix function description kernel-doc notation
nodemask: Drop duplicate check in for_each_node_mask()
lib/bitmap: drop optimization of bitmap_{from,to}_arr64
lib/test_bitmap: increment failure counter properly
Commit 946fa0dbf2d8 ("mm/slub: extend redzone check to extra allocated
kmalloc space than requested") added precise kmalloc redzone poisoning to
the slub_debug functionality.
However, this commit didn't account for HW_TAGS KASAN fully initializing
the object via its built-in memory initialization feature. Even though
HW_TAGS KASAN memory initialization contains special memory initialization
handling for when slub_debug is enabled, it does not account for in-object
slub_debug redzones. As a result, HW_TAGS KASAN can overwrite these
redzones and cause false-positive slub_debug reports.
To fix the issue, avoid HW_TAGS KASAN memory initialization when
slub_debug is enabled altogether. Implement this by moving the
__slub_debug_enabled check to slab_post_alloc_hook. Common slab code
seems like a more appropriate place for a slub_debug check anyway.
Link: https://lkml.kernel.org/r/678ac92ab790dba9198f9ca14f405651b97c8502.1688561016.git.andreyknvl@google.com Fixes: 946fa0dbf2d8 ("mm/slub: extend redzone check to extra allocated kmalloc space than requested") Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reported-by: Will Deacon <will@kernel.org> Acked-by: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: kasan-dev@googlegroups.com Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Collingbourne <pcc@google.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit bb6e04a173f0 ("kasan: use internal prototypes matching gcc-13
builtins") introduced a bug into the memory_is_poisoned_n implementation:
it effectively removed the cast to a signed integer type after applying
KASAN_GRANULE_MASK.
As a result, KASAN started failing to properly check memset, memcpy, and
other similar functions.
Fix the bug by adding the cast back (through an additional signed integer
variable to make the code more readable).
I am going to lose my vrull.eu address at the end of july, and while
adding it to mailmap I also realised that there are more old addresses
from me dangling, so update .mailmap for all of them.
Liu Shixin [Tue, 4 Jul 2023 10:19:42 +0000 (18:19 +0800)]
bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
commit dd0ff4d12dd2 ("bootmem: remove the vmemmap pages from kmemleak in
put_page_bootmem") fix an overlaps existing problem of kmemleak. But the
problem still existed when HAVE_BOOTMEM_INFO_NODE is disabled, because in
this case, free_bootmem_page() will call free_reserved_page() directly.
Fix the problem by adding kmemleak_free_part() in free_bootmem_page() when
HAVE_BOOTMEM_INFO_NODE is disabled.
Link: https://lkml.kernel.org/r/20230704101942.2819426-1-liushixin2@huawei.com Fixes: f41f2ed43ca5 ("mm: hugetlb: free the vmemmap pages associated with each HugeTLB page") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Acked-by: Muchun Song <songmuchun@bytedance.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
writeback: account the number of pages written back
nr_to_write is a count of pages, so we need to decrease it by the number
of pages in the folio we just wrote, not by 1. Most callers specify
either LONG_MAX or 1, so are unaffected, but writeback_sb_inodes() might
end up writing 512x as many pages as it asked for.
Dave added:
: XFS is the only filesystem this would affect, right? AFAIA, nothing
: else enables large folios and uses writeback through
: write_cache_pages() at this point...
:
: In which case, I'd be surprised if much difference, if any, gets
: noticed by anyone.
Link: https://lkml.kernel.org/r/20230628185548.981888-1-willy@infradead.org Fixes: 793917d997df ("mm/readahead: Add large folio readahead") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Jan Kara <jack@suse.cz> Cc: Dave Chinner <david@fromorbit.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit c145e0b47c77 ("mm: streamline COW logic in do_swap_page()") moved
the call to swap_free() before the call to set_pte_at(), which meant that
the MTE tags could end up being freed before set_pte_at() had a chance to
restore them. Fix it by adding a call to the arch_swap_restore() hook
before the call to swap_free().
Link: https://lkml.kernel.org/r/20230523004312.1807357-2-pcc@google.com Link: https://linux-review.googlesource.com/id/I6470efa669e8bd2f841049b8c61020c510678965 Fixes: c145e0b47c77 ("mm: streamline COW logic in do_swap_page()") Signed-off-by: Peter Collingbourne <pcc@google.com> Reported-by: Qun-wei Lin <Qun-wei.Lin@mediatek.com> Closes: https://lore.kernel.org/all/5050805753ac469e8d727c797c2218a9d780d434.camel@mediatek.com/ Acked-by: David Hildenbrand <david@redhat.com> Acked-by: "Huang, Ying" <ying.huang@intel.com> Reviewed-by: Steven Price <steven.price@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> [6.1+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Migration replaces the page in the mapping before copying the contents and
the flags over from the old page, so check that the page in the page cache
is really up to date before using it. Without this, stressing squashfs
reads with parallel compaction sometimes results in squashfs reporting
data corruption.
Link: https://lkml.kernel.org/r/20230629-squashfs-cache-migration-v1-1-d50ebe55099d@axis.com Fixes: e994f5b677ee ("squashfs: cache partial compressed blocks") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Phillip Lougher <phillip@squashfs.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
That happens because a BUG() statement in huge_pte_alloc() attempts to
check that a pte, if present, is a hugetlb pte, but it does so in a
non-lockless-safe manner that leads to a false BUG() report.
We got here due to a couple of bugs, each of which by itself was not quite
enough to cause a problem:
First of all, before commit c33c794828f2("mm: ptep_get() conversion"), the
BUG() statement in huge_pte_alloc() was itself fragile: it relied upon
compiler behavior to only read the pte once, despite using it twice in the
same conditional.
Next, commit c33c794828f2 ("mm: ptep_get() conversion") broke that
delicate situation, by causing all direct pte reads to be done via
READ_ONCE(). And so READ_ONCE() got called twice within the same BUG()
conditional, leading to comparing (potentially, occasionally) different
versions of the pte, and thus to false BUG() reports.
Fix this by taking a single snapshot of the pte before using it in the
BUG conditional.
Now, that commit is only partially to blame here but, people doing
bisections will invariably land there, so this will help them find a fix
for a real crash. And also, the previous behavior was unlikely to ever
expose this bug--it was fragile, yet not actually broken.
So that's why I chose this commit for the Fixes tag, rather than the
commit that created the original BUG() statement.
Link: https://lkml.kernel.org/r/20230701010442.2041858-1-jhubbard@nvidia.com Fixes: c33c794828f2 ("mm: ptep_get() conversion") Signed-off-by: John Hubbard <jhubbard@nvidia.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Acked-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Christian Brauner <brauner@kernel.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: SeongJae Park <sj@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The ocfs2-devel mailing list has been migrated to the kernel.org
infrastructure, update all related documentation pointers to reflect the
change.
Link: https://lkml.kernel.org/r/20230628013437.47030-3-ailiop@suse.com Signed-off-by: Anthony Iliopoulos <ailiop@suse.com> Acked-by: Joseph Qi <jiangqi903@gmail.com> Acked-by: Joel Becker <jlbec@evilplan.org> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mark@fasheh.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
MAINTAINERS: update ocfs2-devel mailing list address
The ocfs2-devel mailing list has been migrated to the kernel.org
infrastructure, update the related entry to reflect the change.
Link: https://lkml.kernel.org/r/20230628013437.47030-2-ailiop@suse.com Signed-off-by: Anthony Iliopoulos <ailiop@suse.com> Acked-by: Joseph Qi <jiangqi903@gmail.com> Acked-by: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
A memory corruption was reported in [1] with bisection pointing to the
patch [2] enabling per-VMA locks for x86. Disable per-VMA locks config to
prevent this issue until the fix is confirmed. This is expected to be a
temporary measure.
fork: lock VMAs of the parent process when forking
Patch series "Avoid memory corruption caused by per-VMA locks", v4.
A memory corruption was reported in [1] with bisection pointing to the
patch [2] enabling per-VMA locks for x86. Based on the reproducer
provided in [1] we suspect this is caused by the lack of VMA locking while
forking a child process.
Patch 1/2 in the series implements proper VMA locking during fork. I
tested the fix locally using the reproducer and was unable to reproduce
the memory corruption problem.
This fix can potentially regress some fork-heavy workloads. Kernel build
time did not show noticeable regression on a 56-core machine while a
stress test mapping 10000 VMAs and forking 5000 times in a tight loop
shows ~7% regression. If such fork time regression is unacceptable,
disabling CONFIG_PER_VMA_LOCK should restore its performance. Further
optimizations are possible if this regression proves to be problematic.
Patch 2/2 disables per-VMA locks until the fix is tested and verified.
This patch (of 2):
When forking a child process, parent write-protects an anonymous page and
COW-shares it with the child being forked using copy_present_pte().
Parent's TLB is flushed right before we drop the parent's mmap_lock in
dup_mmap(). If we get a write-fault before that TLB flush in the parent,
and we end up replacing that anonymous page in the parent process in
do_wp_page() (because, COW-shared with the child), this might lead to some
stale writable TLB entries targeting the wrong (old) page. Similar issue
happened in the past with userfaultfd (see flush_tlb_page() call inside
do_wp_page()).
Lock VMAs of the parent process when forking a child, which prevents
concurrent page faults during fork operation and avoids this issue. This
fix can potentially regress some fork-heavy workloads. Kernel build time
did not show noticeable regression on a 56-core machine while a stress
test mapping 10000 VMAs and forking 5000 times in a tight loop shows ~7%
regression. If such fork time regression is unacceptable, disabling
CONFIG_PER_VMA_LOCK should restore its performance. Further optimizations
are possible if this regression proves to be problematic.
Link: https://lkml.kernel.org/r/20230706011400.2949242-1-surenb@google.com Link: https://lkml.kernel.org/r/20230706011400.2949242-2-surenb@google.com Fixes: 0bff0aaea03e ("x86/mm: try VMA lock-based page fault handling first") Signed-off-by: Suren Baghdasaryan <surenb@google.com> Suggested-by: David Hildenbrand <david@redhat.com> Reported-by: Jiri Slaby <jirislaby@kernel.org> Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/ Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com> Closes: https://lore.kernel.org/all/b198d649-f4bf-b971-31d0-e8433ec2a34c@applied-asynchrony.com/ Reported-by: Jacob Young <jacobly.alt@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=3D217624 Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com> Acked-by: David Hildenbrand <david@redhat.com> Tested-by: Holger Hoffsttte <holger@applied-asynchrony.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Geoff Levand [Thu, 29 Jun 2023 23:32:44 +0000 (23:32 +0000)]
ntb.rst: Fix copy and paste error
It seems the text for the NTB MSI Test Client section was copied from the
NTB Tool Test Client, but was not updated for the new section. Corrects
the NTB MSI Test Client section text.
Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Geoff Levand <geoff@infradead.org> Signed-off-by: Jon Mason <jdmason@kudzu.us>
projects / thirdparty / kernel / linux.git / log
