In commit 8393c524a25609 (MIPS: tlbex: Fix a missing statement for
HUGETLB), the TLB Refill handler was fixed so that non-OCTEON targets
would work properly with huge pages. The change was incorrect in that
it broke the OCTEON case.
In the non-octeon case there is a destructive test for the huge PTE
bit, and then at 0, $k0 is reloaded (that is what the 8393c524a25609
patch added).
In the octeon case, we modify k1 in the branch delay slot, but we
never need k0 again, so the new load is not needed, but since k1 is
modified, if we do the load, we load from a garbage location and then
get a nested TLB Refill, which is seen in userspace as either SIGBUS
or SIGSEGV (depending on the garbage).
The real fix is to only do this reloading if it is needed, and never
where it is harmful.
Code before the .fixup section needs to have the .insn directive.
This has no side effects on MIPS32/64 but it affects the way microMIPS
loads the address for the return label.
Fixes the following build problem:
mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x4a0: Unsupported jump between
ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value
Makefile:819: recipe for target 'vmlinux' failed
The fix is similar to 1658f914ff91c3bf ("MIPS: microMIPS:
Disable LL/SC and fix linker bug.")
This patch fixes a bug in handling of SPC-3 PR Activate Persistence
across Target Power Loss (APTPL) logic where re-creation of state for
MappedLUNs from dynamically generated NodeACLs did not occur during
I_T Nexus establishment.
It adds the missing core_scsi3_check_aptpl_registration() call during
core_tpg_check_initiator_node_acl() -> core_tpg_add_node_to_devs() in
order to replay any pre-loaded APTPL metadata state associated with
the newly connected SCSI Initiator Port.
Cc: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
During temporary resource starvation at lower transport layer, command
is placed on queue full retry path, which expose this problem. The TCM
queue full handling of SCF_TRANSPORT_TASK_SENSE currently sends the same
cmd twice to lower layer. The 1st time led to cmd normal free path.
The 2nd time cause Null pointer access.
This regression bug was originally introduced v3.1-rc code in the
following commit:
The code is currently riddled with "drop the hardware_lock to avoid a
deadlock" bugs that expose races. One of those races seems to expose a
valid warning in tcm_qla2xxx_clear_nacl_from_fcport_map. Add some
bandaid to it.
Signed-off-by: Joern Engel <joern@logfs.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On systems with invvpid instruction support (corresponding bit in
IA32_VMX_EPT_VPID_CAP MSR is set) guest invocation of invvpid
causes vm exit, which is currently not handled and results in
propagation of unknown exit to userspace.
Fix this by installing an invvpid vm exit handler.
This is CVE-2014-3646.
Signed-off-by: Petr Matousek <pmatouse@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Before changing rip (during jmp, call, ret, etc.) the target should be asserted
to be canonical one, as real CPUs do. During sysret, both target rsp and rip
should be canonical. If any of these values is noncanonical, a #GP exception
should occur. The exception to this rule are syscall and sysenter instructions
in which the assigned rip is checked during the assignment to the relevant
MSRs.
This patch fixes the emulator to behave as real CPUs do for near branches.
Far branches are handled by the next patch.
This fixes CVE-2014-3647.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
KVM_EXIT_UNKNOWN is a kvm bug, we don't really know whether it was
triggered by a priveledged application. Let's not kill the guest: WARN
and inject #UD instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Upon WRMSR, the CPU should inject #GP if a non-canonical value (address) is
written to certain MSRs. The behavior is "almost" identical for AMD and Intel
(ignoring MSRs that are not implemented in either architecture since they would
anyhow #GP). However, IA32_SYSENTER_ESP and IA32_SYSENTER_EIP cause #GP if
non-canonical address is written on Intel but not on AMD (which ignores the top
32-bits).
Accordingly, this patch injects a #GP on the MSRs which behave identically on
Intel and AMD. To eliminate the differences between the architecutres, the
value which is written to IA32_SYSENTER_ESP and IA32_SYSENTER_EIP is turned to
canonical value before writing instead of injecting a #GP.
Some references from Intel and AMD manuals:
According to Intel SDM description of WRMSR instruction #GP is expected on
WRMSR "If the source register contains a non-canonical address and ECX
specifies one of the following MSRs: IA32_DS_AREA, IA32_FS_BASE, IA32_GS_BASE,
IA32_KERNEL_GS_BASE, IA32_LSTAR, IA32_SYSENTER_EIP, IA32_SYSENTER_ESP."
According to AMD manual instruction manual:
LSTAR/CSTAR (SYSCALL): "The WRMSR instruction loads the target RIP into the
LSTAR and CSTAR registers. If an RIP written by WRMSR is not in canonical
form, a general-protection exception (#GP) occurs."
IA32_GS_BASE and IA32_FS_BASE (WRFSBASE/WRGSBASE): "The address written to the
base field must be in canonical form or a #GP fault will occur."
IA32_KERNEL_GS_BASE (SWAPGS): "The address stored in the KernelGSbase MSR must
be in canonical form."
This patch fixes CVE-2014-3610.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There's a race condition in the PIT emulation code in KVM. In
__kvm_migrate_pit_timer the pit_timer object is accessed without
synchronization. If the race condition occurs at the wrong time this
can crash the host kernel.
This fixes CVE-2014-3611.
Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The previous patch blocked invalid writes directly when the MSR
is written. As a precaution, prevent future similar mistakes by
gracefulling handle GPs caused by writes to shared MSRs.
Signed-off-by: Andrew Honig <ahonig@google.com>
[Remove parts obsoleted by Nadav's patch. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The third parameter of kvm_unpin_pages() when called from
kvm_iommu_map_pages() is wrong, it should be the number of pages to un-pin
and not the page size.
This error was facilitated with an inconsistent API: kvm_pin_pages() takes
a size, but kvn_unpin_pages() takes a number of pages, so fix the problem
by matching the two.
This was introduced by commit 350b8bd ("kvm: iommu: fix the third parameter
of kvm_iommu_put_pages (CVE-2014-3601)"), which fixes the lack of
un-pinning for pages intended to be un-pinned (i.e. memory leak) but
unfortunately potentially aggravated the number of pages we un-pin that
should have stayed pinned. As far as I understand though, the same
practical mitigations apply.
This issue was found during review of Red Hat 6.6 patches to prepare
Ksplice rebootless updates.
Thanks to Vegard for his time on a late Friday evening to help me in
understanding this code.
Fix a copy-paste bug when converting to the control framework.
Fixes: commit 5d478e0de871 ("[media] tda7432: convert to the control framework") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not
automatically power down. This blocks other receivers connected
to a satellite channel router (EN50494), since the receivers can not send the
required DiSEqC sequences when the Tevii card is connected to a the same SCR.
This patch switches off the LNB supply voltage on initialization of the frontend.
[mchehab@osg.samsung.com: add a comment about why we're explicitly
turning off voltage at device init] Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a new video frame is started, the driver takes the next video buffer from
the list of active buffers and moves it to dev->usb_ctl.vid_buf / dev->usb_ctl.vbi_buf
for further processing.
On streaming stop we currently only give back the pending buffers from the list
but not the ones which are currently processed.
This causes the following warning from the vb2 core since kernel 3.15:
Fix clamp_align() used in v4l_bound_align_image() to prevent overflow
when passed large value like UINT32_MAX.
In the current implementation:
clamp_align(UINT32_MAX, 8, 8192, 3)
returns 8, because in line:
x = (x + (1 << (align - 1))) & mask;
x overflows to (-1 + 4) & 0x7 = 3, while expected value is 8192.
v4l_bound_align_image() is heavily used in VIDIOC_S_FMT and
VIDIOC_SUBDEV_S_FMT ioctls handlers, and documentation of the latter
explicitly states that:
"The modified format should be as close as possible to the original
request."
-- http://linuxtv.org/downloads/v4l-dvb-apis/vidioc-subdev-g-fmt.html
Thus one would expect, that passing UINT32_MAX as format width and
height will result in setting maximum possible resolution for the
device. Particularly, when the driver doesn't support
VIDIOC_ENUM_FRAMESIZES ioctl, which is common in the codebase.
The translation from the X driver to the KMS one typo'ed a couple
of array indices, causing the HW cursor to look weird (blocky with
leaking edge colors). This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The framebuffer code uses the current background color to fill the border
when switching consoles, however, this results in inconsistent behavior.
For example:
- start Midnigh Commander
- the border is black
- switch to another console and switch back
- the border is cyan
- type something into the command line in mc
- the border is cyan
- switch to another console and switch back
- the border is black
- press F9 to go to menu
- the border is black
- switch to another console and switch back
- the border is dark blue
When switching to a console with Midnight Commander, the border is random
color that was left selected by the slang subsystem.
This patch fixes this inconsistency by always using black as the
background color when switching consoles.
There are two threads running on the system. The first thread is a system
monitoring thread that is reading /proc/modules. The second thread is
loading and unloading a module (in this example I'm using my simple
dummy-module.ko). Note, in the "real world" this occurred with the qlogic
driver module.
CPU 0 (/proc/modules reader)
CPU 1 (loading/unloading module)
CPU 0 opens /proc/modules, and starts displaying data for each module by
traversing the modules list via fs/seq_file.c:seq_open() and
fs/seq_file.c:seq_read(). For each module in the modules list, seq_read
does
op->start() <-- this is a pointer to m_start()
op->show() <- this is a pointer to m_show()
op->stop() <-- this is a pointer to m_stop()
The m_start(), m_show(), and m_stop() module functions are defined in
kernel/module.c. The m_start() and m_stop() functions acquire and release
the module_mutex respectively.
ie) When reading /proc/modules, the module_mutex is acquired and released
for each module.
m_show() is called with the module_mutex held. It accesses the module
struct data and attempts to write out module data. It is in this code
path that the above BUG_ON() warning is encountered, specifically m_show()
calls
The other thread, CPU 1, in unloading the module calls the syscall
delete_module() defined in kernel/module.c. The module_mutex is acquired
for a short time, and then released. free_module() is called without the
module_mutex. free_module() then sets mod->state = MODULE_STATE_UNFORMED,
also without the module_mutex. Some additional code is called and then the
module_mutex is reacquired to remove the module from the modules list:
/* Now we can delete it from the lists */
mutex_lock(&module_mutex);
stop_machine(__unlink_module, mod, NULL);
mutex_unlock(&module_mutex);
This is the sequence of events that leads to the panic.
CPU 1 is removing dummy_module via delete_module(). It acquires the
module_mutex, and then releases it. CPU 1 has NOT set dummy_module->state to
MODULE_STATE_UNFORMED yet.
CPU 0, which is reading the /proc/modules, acquires the module_mutex and
acquires a pointer to the dummy_module which is still in the modules list.
CPU 0 calls m_show for dummy_module. The check in m_show() for
MODULE_STATE_UNFORMED passed for dummy_module even though it is being
torn down.
Meanwhile CPU 1, which has been continuing to remove dummy_module without
holding the module_mutex, now calls free_module() and sets
dummy_module->state to MODULE_STATE_UNFORMED.
CPU 0 now calls module_flags() with dummy_module and ...
Acquire and release the module_mutex lock around the setting of
MODULE_STATE_UNFORMED in the teardown path, which should resolve the
problem.
Testing: In the unpatched kernel I can panic the system within 1 minute by
doing
while (true) do insmod dummy_module.ko; rmmod dummy_module.ko; done
and
while (true) do cat /proc/modules; done
in separate terminals.
In the patched kernel I was able to run just over one hour without seeing
any issues. I also verified the output of panic via sysrq-c and the output
of /proc/modules looks correct for all three states for the dummy_module.
The math in both blk_stack_limits() and queue_limit_alignment_offset()
assume that a block device's io_min (aka minimum_io_size) is always a
power-of-2. Fix the math such that it works for non-power-of-2 io_min.
This issue (of alignment_offset != 0) became apparent when testing
dm-thinp with a thinp blocksize that matches a RAID6 stripesize of
1280K. Commit fdfb4c8c1 ("dm thin: set minimum_io_size to pool's data
block size") unlocked the potential for alignment_offset != 0 due to
the dm-thin-pool's io_min possibly being a non-power-of-2.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 98683650 "Merge branch 'drbd-8.4_ed6' into
for-3.8-drivers-drbd-8.4_ed6" switches to the new augment API, but the
new API requires that the tree is augmented before rb_insert_augmented()
is called, which is missing.
So we add the augment-code to drbd_insert_interval() when it travels the
tree up to down before rb_insert_augmented(). See the example in
include/linux/interval_tree_generic.h or Documentation/rbtree.txt.
drbd_insert_interval() may cancel the insertion when traveling, in this
case, the just added augment-code does nothing before cancel since the
@this node is already in the subtrees in this case.
CC: Michel Lespinasse <walken@google.com> Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Andreas Gruenbacher <agruen@linbit.com> Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When __scan frees the required number of buffer entries that the
shrinker requested (nr_to_scan becomes zero) it must return. Before
this fix the __scan code exited only the inner loop and continued in the
outer loop -- which could result in reduced performance due to extra
buffers being freed (e.g. unnecessarily evicted thinp metadata needing
to be synchronously re-read into bufio's cache).
Also, move dm_bufio_cond_resched to __scan's inner loop, so that
iterating the bufio client's lru lists doesn't result in scheduling
latency.
Reported-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The 'last_accessed' member of the dm_buffer structure was only set when
the the buffer was created. This led to each buffer being discarded
after dm_bufio_max_age time even if it was used recently. In practice
this resulted in all thinp metadata being evicted soon after being read
-- this is particularly problematic for metadata intensive workloads
like multithreaded small random IO.
'last_accessed' is now updated each time the buffer is moved to the head
of the LRU list, so the buffer is now properly discarded if it was not
used in dm_bufio_max_age time.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On restore, virtio pci does the following:
+ set features
+ init vqs etc - device can be used at this point!
+ set ACKNOWLEDGE,DRIVER and DRIVER_OK status bits
This is in violation of the virtio spec, which
requires the following order:
- ACKNOWLEDGE
- DRIVER
- init vqs
- DRIVER_OK
This behaviour will break with hypervisors that assume spec compliant
behaviour. It seems like a good idea to have this patch applied to
stable branches to reduce the support butden for the hypervisors.
Cc: Amit Shah <amit.shah@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
sb_finish_set_opts() can race with inode_free_security()
when initializing inode security structures for inodes
created prior to initial policy load or by the filesystem
during ->mount(). This appears to have always been
a possible race, but commit 3dc91d4 ("SELinux: Fix possible
NULL pointer dereference in selinux_inode_permission()")
made it more evident by immediately reusing the unioned
list/rcu element of the inode security structure for call_rcu()
upon an inode_free_security(). But the underlying issue
was already present before that commit as a possible use-after-free
of isec.
Shivnandan Kumar reported the list corruption and proposed
a patch to split the list and rcu elements out of the union
as separate fields of the inode_security_struct so that setting
the rcu element would not affect the list element. However,
this would merely hide the issue and not truly fix the code.
This patch instead moves up the deletion of the list entry
prior to dropping the sbsec->isec_lock initially. Then,
if the inode is dropped subsequently, there will be no further
references to the isec.
Reported-by: Shivnandan Kumar <shivnandan.k@samsung.com> Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
pci_enable_msi() can return failure with both positive and negative
integers -- it returns 0 for success -- but is only tested here for
"if (ret < 0)". This causes us to try to use MSI on the RTS5249 SD
reader in the Dell XPS 11 when enabling MSI failed, causing:
[ 1.737110] rtsx_pci: probe of 0000:05:00.0 failed with error -110
Reported-by: D. Jared Dominguez <Jared_Dominguez@Dell.com> Tested-by: D. Jared Dominguez <Jared_Dominguez@Dell.com> Signed-off-by: Chris Ball <chris@printf.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Andy Lutomirski recently demonstrated that when chroot is used to set
the root path below the path for the new ``root'' passed to pivot_root
the pivot_root system call succeeds and leaks mounts.
In examining the code I see that starting with a new root that is
below the current root in the mount tree will result in a loop in the
mount tree after the mounts are detached and then reattached to one
another. Resulting in all kinds of ugliness including a leak of that
mounts involved in the leak of the mount loop.
Prevent this problem by ensuring that the new mount is reachable from
the current root of the mount tree.
[Added stable cc. Fixes CVE-2014-7970. --Andy]
Reported-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Andy Lutomirski <luto@amacapital.net> Link: http://lkml.kernel.org/r/87bnpmihks.fsf@x220.int.ebiederm.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
I ran into this error after a ubiupdatevol, because I forgot to backport e9110361a9a4 UBI: fix the volumes tree sorting criteria.
UBI error: process_pool_aeb: orphaned volume in fastmap pool
UBI error: ubi_scan_fastmap: Attach by fastmap failed, doing a full scan!
kmem_cache_destroy ubi_ainf_peb_slab: Slab cache still has objects
CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.18-00053-gf05cac8dbf85 #1
[<c000d298>] (unwind_backtrace) from [<c000baa8>] (show_stack+0x10/0x14)
[<c000baa8>] (show_stack) from [<c01b7a68>] (destroy_ai+0x230/0x244)
[<c01b7a68>] (destroy_ai) from [<c01b8fd4>] (ubi_attach+0x98/0x1ec)
[<c01b8fd4>] (ubi_attach) from [<c01ade90>] (ubi_attach_mtd_dev+0x2b8/0x868)
[<c01ade90>] (ubi_attach_mtd_dev) from [<c038b510>] (ubi_init+0x1dc/0x2ac)
[<c038b510>] (ubi_init) from [<c0008860>] (do_one_initcall+0x94/0x140)
[<c0008860>] (do_one_initcall) from [<c037aadc>] (kernel_init_freeable+0xe8/0x1b0)
[<c037aadc>] (kernel_init_freeable) from [<c02730ac>] (kernel_init+0x8/0xe4)
[<c02730ac>] (kernel_init) from [<c00093f0>] (ret_from_fork+0x14/0x24)
UBI: scanning is finished
Freeing the cache in the error path fixes the Slab error.
Tested on at91sam9g35 (3.14.18+fastmap backports)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
zatimend has reported that in his environment (3.16/gcc4.8.3/corei7)
memset() calls which clear out sensitive data in extract_{buf,entropy,
entropy_user}() in random driver are being optimized away by gcc.
Add a helper memzero_explicit() (similarly as explicit_bzero() variants)
that can be used in such cases where a variable with sensitive data is
being cleared out in the end. Other use cases might also be in crypto
code. [ I have put this into lib/string.c though, as it's always built-in
and doesn't need any dependencies then. ]
Starting with Linux 3.12 processes get stuck in D state forever in
UserModeLinux under sync heavy workloads. This bug was introduced by
commit 805f11a0d5 (um: ubd: Add REQ_FLUSH suppport).
Fix bug by adding a check if FLUSH request was successfully submitted to
the I/O thread and keeping the FLUSH request on the request queue on
submission failures.
we used to check for "nobody else could start doing anything with
that opened file" by checking that refcount was 2 or less - one
for descriptor table and one we'd acquired in fget() on the way to
wherever we are. That was race-prone (somebody else might have
had a reference to descriptor table and do fget() just as we'd
been checking) and it had become flat-out incorrect back when
we switched to fget_light() on those codepaths - unlike fget(),
it doesn't grab an extra reference unless the descriptor table
is shared. The same change allowed a race-free check, though -
we are safe exactly when refcount is less than 2.
It was a long time ago; pre-2.6.12 for ioctl() (the codepath leading
to ppp one) and 2.6.17 for sendmsg() (netlink one). OTOH,
netlink hadn't grown that check until 3.9 and ppp used to live
in drivers/net, not drivers/net/ppp until 3.1. The bug existed
well before that, though, and the same fix used to apply in old
location of file.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
schedule_delayed_work() happening when the work is already pending is
a cheap no-op. Don't bother with ->wbuf_queued logics - it's both
broken (cancelling ->wbuf_dwork leaves it set, as spotted by Jeff Harris)
and pointless. It's cheaper to let schedule_delayed_work() handle that
case.
Reported-by: Jeff Harris <jefftharris@gmail.com> Tested-by: Jeff Harris <jefftharris@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
AFAICS, prepend_name() is broken on SMP alpha. Disclaimer: I don't have
SMP alpha boxen to reproduce it on. However, it really looks like the race
is real.
CPU1: d_path() on /mnt/ramfs/<255-character>/foo
CPU2: mv /mnt/ramfs/<255-character> /mnt/ramfs/<63-character>
CPU2 does d_alloc(), which allocates an external name, stores the name there
including terminating NUL, does smp_wmb() and stores its address in
dentry->d_name.name. It proceeds to d_add(dentry, NULL) and d_move()
old dentry over to that. ->d_name.name value ends up in that dentry.
In the meanwhile, CPU1 gets to prepend_name() for that dentry. It fetches
->d_name.name and ->d_name.len; the former ends up pointing to new name
(64-byte kmalloc'ed array), the latter - 255 (length of the old name).
Nothing to force the ordering there, and normally that would be OK, since we'd
run into the terminating NUL and stop. Except that it's alpha, and we'd need
a data dependency barrier to guarantee that we see that store of NUL
__d_alloc() has done. In a similar situation dentry_cmp() would survive; it
does explicit smp_read_barrier_depends() after fetching ->d_name.name.
prepend_name() doesn't and it risks walking past the end of kmalloc'ed object
and possibly oops due to taking a page fault in kernel mode.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In compat mode, we copy each field of snd_pcm_status struct but don't
touch the reserved fields, and this leaves uninitialized values
there. Meanwhile the native ioctl does zero-clear the whole
structure, so we should follow the same rule in compat mode, too.
evm_inode_setxattr() can be called with no value. The function does not
check the length so that following command can be used to produce the
kernel oops: setfattr -n security.evm FOO. This patch fixes it.
Changes in v3:
* there is no reason to return different error codes for EVM_XATTR_HMAC
and non EVM_XATTR_HMAC. Remove unnecessary test then.
Changes in v2:
* testing for validity of xattr type
pte_pfn() returns a PFN of long (32 bits in 32-PAE), so "long <<
PAGE_SHIFT" will overflow for PFNs above 4GB.
Due to this issue, some Linux 32-PAE distros, running as guests on Hyper-V,
with 5GB memory assigned, can't load the netvsc driver successfully and
hence the synthetic network device can't work (we can use the kernel parameter
mem=3000M to work around the issue).
The NT flag doesn't do anything in long mode other than causing IRET
to #GP. Oddly, CPL3 code can still set NT using popf.
Entry via hardware or software interrupt clears NT automatically, so
the only relevant entries are fast syscalls.
If user code causes kernel code to run with NT set, then there's at
least some (small) chance that it could cause trouble. For example,
user code could cause a call to EFI code with NT set, and who knows
what would happen? Apparently some games on Wine sometimes do
this (!), and, if an IRET return happens, they will segfault. That
segfault cannot be handled, because signal delivery fails, too.
This patch programs the CPU to clear NT on entry via SYSCALL (both
32-bit and 64-bit, by my reading of the AMD APM), and it clears NT
in software on entry via SYSENTER.
To save a few cycles, this borrows a trick from Jan Beulich in Xen:
it checks whether NT is set before trying to clear it. As a result,
it seems to have very little effect on SYSENTER performance on my
machine.
There's another minor bug fix in here: it looks like the CFI
annotations were wrong if CONFIG_AUDITSYSCALL=n.
Testers beware: on Xen, SYSENTER with NT set turns into a GPF.
I haven't touched anything on 32-bit kernels.
The syscall mask change comes from a variant of this patch by Anish
Bhatt.
Note to stable maintainers: there is no known security issue here.
A misguided program can set NT and cause the kernel to try and fail
to deliver SIGSEGV, crashing the program. This patch fixes Far Cry
on Wine: https://bugs.winehq.org/show_bug.cgi?id=33275
save_xstate_sig()->drop_init_fpu() doesn't look right. setup_rt_frame()
can fail after that, in this case the next setup_rt_frame() triggered
by SIGSEGV won't save fpu simply because the old state was lost. This
obviously mean that fpu won't be restored after sys_rt_sigreturn() from
SIGSEGV handler.
Shift drop_init_fpu() into !failed branch in handle_signal().
Add preempt_disable() + preempt_enable() around math_state_restore() in
__restore_xstate_sig(). Otherwise __switch_to() after __thread_fpu_begin()
can overwrite fpu->state we are going to restore.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Link: http://lkml.kernel.org/r/20140902175717.GA21649@redhat.com Reviewed-by: Suresh Siddha <sbsiddha@gmail.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It is currently possible to execve() an x32 executable on an x86_64
kernel that has only ia32 compat enabled. However all its syscalls
will fail, even _exit(). This usually causes it to segfault.
Change the ELF compat architecture check so that x32 executables are
rejected if we don't support the x32 ABI.
->page_mkwrite() is used by filesystems to allocate blocks under a page
which is becoming writeably mmapped in some process' address space. This
allows a filesystem to return a page fault if there is not enough space
available, user exceeds quota or similar problem happens, rather than
silently discarding data later when writepage is called.
However VFS fails to call ->page_mkwrite() in all the cases where
filesystems need it when blocksize < pagesize. For example when
blocksize = 1024, pagesize = 4096 the following is problematic:
ftruncate(fd, 0);
pwrite(fd, buf, 1024, 0);
map = mmap(NULL, 1024, PROT_WRITE, MAP_SHARED, fd, 0);
map[0] = 'a'; ----> page_mkwrite() for index 0 is called
ftruncate(fd, 10000); /* or even pwrite(fd, buf, 1, 10000) */
mremap(map, 1024, 10000, 0);
map[4095] = 'a'; ----> no page_mkwrite() called
At the moment ->page_mkwrite() is called, filesystem can allocate only
one block for the page because i_size == 1024. Otherwise it would create
blocks beyond i_size which is generally undesirable. But later at
->writepage() time, we also need to store data at offset 4095 but we
don't have block allocated for it.
This patch introduces a helper function filesystems can use to have
->page_mkwrite() called at all the necessary moments.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Hu (hujianyang <hujianyang@huawei.com>) discovered an issue in the
'empty_log_bytes()' function, which calculates how many bytes are left in the
log:
"
If 'c->lhead_lnum + 1 == c->ltail_lnum' and 'c->lhead_offs == c->leb_size', 'h'
would equalent to 't' and 'empty_log_bytes()' would return 'c->log_bytes'
instead of 0.
"
At this point it is not clear what would be the consequences of this, and
whether this may lead to any problems, but this patch addresses the issue just
in case.
Hu (hujianyang@huawei.com) discovered a race condition which may lead to a
situation when UBIFS is unable to mount the file-system after an unclean
reboot. The problem is theoretical, though.
In UBIFS, we have the log, which basically a set of LEBs in a certain area. The
log has the tail and the head.
Every time user writes data to the file-system, the UBIFS journal grows, and
the log grows as well, because we append new reference nodes to the head of the
log. So the head moves forward all the time, while the log tail stays at the
same position.
At any time, the UBIFS master node points to the tail of the log. When we mount
the file-system, we scan the log, and we always start from its tail, because
this is where the master node points to. The only occasion when the tail of the
log changes is the commit operation.
The commit operation has 2 phases - "commit start" and "commit end". The former
is relatively short, and does not involve much I/O. During this phase we mostly
just build various in-memory lists of the things which have to be written to
the flash media during "commit end" phase.
During the commit start phase, what we do is we "clean" the log. Indeed, the
commit operation will index all the data in the journal, so the entire journal
"disappears", and therefore the data in the log become unneeded. So we just
move the head of the log to the next LEB, and write the CS node there. This LEB
will be the tail of the new log when the commit operation finishes.
When the "commit start" phase finishes, users may write more data to the
file-system, in parallel with the ongoing "commit end" operation. At this point
the log tail was not changed yet, it is the same as it had been before we
started the commit. The log head keeps moving forward, though.
The commit operation now needs to write the new master node, and the new master
node should point to the new log tail. After this the LEBs between the old log
tail and the new log tail can be unmapped and re-used again.
And here is the possible problem. We do 2 operations: (a) We first update the
log tail position in memory (see 'ubifs_log_end_commit()'). (b) And then we
write the master node (see the big lock of code in 'do_commit()').
But nothing prevents the log head from moving forward between (a) and (b), and
the log head may "wrap" now to the old log tail. And when the "wrap" happens,
the contends of the log tail gets erased. Now a power cut happens and we are in
trouble. We end up with the old master node pointing to the old tail, which was
erased. And replay fails because it expects the master node to point to the
correct log tail at all times.
This patch merges the abovementioned (a) and (b) operations by moving the master
node change code to the 'ubifs_log_end_commit()' function, so that it runs with
the log mutex locked, which will prevent the log from being changed benween
operations (a) and (b).
The 'mst_mutex' is not needed since because 'ubifs_write_master()' is only
called on the mount path and commit path. The mount path is sequential and
there is no parallelism, and the commit path is also serialized - there is only
one commit going on at a time.
The man page for open(2) indicates that when O_CREAT is specified, the
'mode' argument applies only to future accesses to the file:
Note that this mode applies only to future accesses of the newly
created file; the open() call that creates a read-only file
may well return a read/write file descriptor.
The man page for open(2) implies that 'mode' is treated identically by
O_CREAT and O_TMPFILE.
But for O_TMPFILE, do_tmpfile() passes the full op->acc_mode to
may_open().
This patch lines up the behavior of O_TMPFILE with O_CREAT. After the
inode is created, may_open() is called with acc_mode = MAY_OPEN, in
do_tmpfile().
A different, but related glibc bug revealed the discrepancy:
https://sourceware.org/bugzilla/show_bug.cgi?id=17523
The glibc lazily loads the 'mode' argument of open() and openat() using
va_arg() only if O_CREAT is present in 'flags' (to support both the 2
argument and the 3 argument forms of open; same idea for openat()).
However, the glibc ignores the 'mode' argument if O_TMPFILE is in
'flags'.
On x86_64, for open(), it magically works anyway, as 'mode' is in
RDX when entering open(), and is still in RDX on SYSCALL, which is where
the kernel looks for the 3rd argument of a syscall.
But openat() is not quite so lucky: 'mode' is in RCX when entering the
glibc wrapper for openat(), while the kernel looks for the 4th argument
of a syscall in R10. Indeed, the syscall calling convention differs from
the regular calling convention in this respect on x86_64. So the kernel
sees mode = 0 when trying to use glibc openat() with O_TMPFILE, and
fails with EACCES.
Signed-off-by: Eric Rannaud <e@nanocritical.com> Acked-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
While total_objects is a "long", total_objects == 0 unlikely happens for
3.12 and later kernels because 32-bit architectures would not be able to
hold (1 << 32) objects. However, total_objects == 0 may happen for kernels
between 3.1 and 3.11 because total_objects in prune_super() was an "int"
and (e.g.) x86_64 architecture might be able to hold (1 << 32) objects.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch makes it possible to kill a process looping in
cont_expand_zero. A process may spend a lot of time in this function, so
it is desirable to be able to kill it.
It happened to me that I wanted to copy a piece data from the disk to a
file. By mistake, I used the "seek" parameter to dd instead of "skip". Due
to the "seek" parameter, dd attempted to extend the file and became stuck
doing so - the only possibility was to reset the machine or wait many
hours until the filesystem runs out of space and cont_expand_zero fails.
We need this patch to be able to terminate the process.
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Coverity spotted the following possible use-after-free condition in
dapm_create_or_share_mixmux_kcontrol():
If kcontrol is NULL, and (wname_in_long_name && kcname_in_long_name)
validates to true, 'name' will be set to an allocated string, and be
freed a few lines later via the 'long_name' alias. 'name', however,
is used by dev_err() in case snd_ctl_add() fails.
Fix this by adding a jump label that frees 'long_name' at the end of
the function.
Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently, ata_sff_softreset is skipped for controllers with no ctl port.
But that also skips ata_sff_dev_classify required for device detection.
This means that libata is currently broken on controllers with no ctl port.
The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:
[ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
[ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current]
[ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out
[ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
[ 2431.851210] end_request: I/O error, dev sr0, sector 121808
When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:
lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:
00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
Flags: bus master, medium devsel, latency 64
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=4]
I/O ports at 1440 [size=16]
Kernel driver in use: pata_serverworks
The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.
This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:
find /mnt -type f -print | xargs cat > /dev/null
The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.
Signed-off-by: Scott Carter <ccscott@funsoft.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This reverts commit 3189eddbcafc ("percpu: free percpu allocation info for
uniprocessor system").
The commit causes a hang with a crisv32 image. This may be an architecture
problem, but at least for now the revert is necessary to be able to boot a
crisv32 image.
Cc: Tejun Heo <tj@kernel.org> Cc: Honggang Li <enjoymindful@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 3189eddbcafc ("percpu: free percpu allocation info for uniprocessor system") Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ARM has some private syscalls (for example, set_tls(2)) which lie
outside the range of NR_syscalls. If any of these are called while
syscall tracing is being performed, out-of-bounds array access will
occur in the ftrace and perf sys_{enter,exit} handlers.
# trace-cmd record -e syscalls:* true
[ 17.289329] Unable to handle kernel paging request at virtual address aaaaaace
[ 17.289590] pgd = 9e71c000
[ 17.289696] [aaaaaace] *pgd=00000000
[ 17.289985] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 17.290169] Modules linked in:
[ 17.290391] CPU: 0 PID: 704 Comm: true Not tainted 3.18.0-rc2+ #21
[ 17.290585] task: 9f4dab00 ti: 9e710000 task.ti: 9e710000
[ 17.290747] PC is at ftrace_syscall_enter+0x48/0x1f8
[ 17.290866] LR is at syscall_trace_enter+0x124/0x184
Fix this by ignoring out-of-NR_syscalls-bounds syscall numbers.
Commit cd0980fc8add "tracing: Check invalid syscall nr while tracing syscalls"
added the check for less than zero, but it should have also checked
for greater than NR_syscalls.
Link: http://lkml.kernel.org/p/1414620418-29472-1-git-send-email-rabin@rab.in Fixes: cd0980fc8add "tracing: Check invalid syscall nr while tracing syscalls" Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[Only use the compiler.h portion of this patch, to get the
OPTIMIZER_HIDE_VAR() macro, which we need for other -stable patches
- gregkh]
Disabling compiler optimizations can be fragile, since a new
optimization could be added to -O0 or -Os that breaks the assumptions
the code is making.
Instead of disabling compiler optimizations, use a dummy inline assembly
(based on RELOC_HIDE) to block the problematic kinds of optimization,
while still allowing other optimizations to be applied to the code.
The dummy inline assembly is added after every OR, and has the
accumulator variable as its input and output. The compiler is forced to
assume that the dummy inline assembly could both depend on the
accumulator variable and change the accumulator variable, so it is
forced to compute the value correctly before the inline assembly, and
cannot assume anything about its value after the inline assembly.
This change should be enough to make crypto_memneq work correctly (with
data-independent timing) even if it is inlined at its call sites. That
can be done later in a followup patch.
Compile-tested on x86_64.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.eti.br> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
0411,0241 RT5572 BUFFALO WI-U2-300D Wireless LAN Adapter
0789,0170 RT3572 Logitec LAN-W300AN/U2
0846,9013 RT3573 NETGEAR Adaptador USB Inalambrico Movistar
0df6,006e RT3573 Sitecom WiFi USB adapter N900
2001,3c1f RT3573 D-Link DWA-162 Wireless N900 Dual Band Adapter
2001,3c20 RT5372 D-Link DWA-140 Wireless N USB Adapter(rev.D)
2001,3c21 RT5572 D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C)
2001,3c22 RT5372 D-Link DWA-132 Wireless N USB Adapter(rev.B)
2001,3c23 RT5372 D-Link GO-USB-N300 Wireless N Easy USB Adapter
2019,ab29 ? Planex GW-USMirco300
20f4,724a RT5572 TRENDnet N600 Wireless Dual Band USB Adapter
Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch adds intel_mid clovertrail SDIO and eMMC device
IDs to the sdhci-pci driver.
Signed-off-by: Eric Ernst <eric.ernst@linux.intel.com> Signed-off-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The xpad driver recognizes Razer Sabertooth controllers as generic xbox
controller, while it is really a 360 controller. This patch adds pid/vid
mappings for the controller so that it is correctly recognized.
When using Razer Onza controller the dpad doesn't work in many games
because D-PAD was mapped to buttons (useful for dance pads) and not to
HAT0X/Y axis.
ers who really want to have it mapped to buttons can restore previous
behavior by using 'dpad_to_buttons' module option.
Signed-off-by: Thomaz de Oliveira dos Reis <thor27@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
btmrvl_add_card() function calls kthread_run that might return error
(e.g. if current thread is killed). If one tries to use the error
value as a pointer then invalid memory access oops happens.
Check kthread_run() return value, if it is an error then release resources
correctly.
TEST=boot computer with BT modules enabled. I see the error message that
BT device initialization failed. Now kernel does not crash. Hint: to enable
BT run 'rmmod btmrvl_sdio; modprobe btmrvl_sdio'
The Asus Z97-DELUXE motherboard contains a Broadcom based Bluetooth
controller on the USB bus. However vendor and product ID are listed
as ASUSTek Computer.
The ath3k driver is treating the version information badly when it
comes to loading the right firmware version and comparing that it
actually matches with the hardware.
Initially this showed up as this:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:373:17: warning: cast to restricted __le32
drivers/bluetooth/ath3k.c:435:17: warning: cast to restricted __le32
However when fixing this by actually using __packed and __le32 for
the ath3_version structure, more issues came up:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:381:32: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:381:32: expected restricted __le32 [usertype] rom_version
drivers/bluetooth/ath3k.c:381:32: got int [signed] <noident>
drivers/bluetooth/ath3k.c:382:34: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:382:34: expected restricted __le32 [usertype] build_version
drivers/bluetooth/ath3k.c:382:34: got int [signed] <noident>
drivers/bluetooth/ath3k.c:386:28: warning: restricted __le32 degrades to integer
drivers/bluetooth/ath3k.c:386:56: warning: restricted __le32 degrades to integer
This patch fixes every instance of the firmware version handling and
makes sure it is endian safe and uses proper unaligned access.
The isochronous endpoints are not valid when the Intel Bluetooth
controller boots up in bootloader mode. So just mark these endpoints
as broken and then they will not be configured.
The interrupt interface for the Intel USB bootloader devices is only
enabled after receiving SetInterface(0, AltSetting=0). When this USB
command is not send, then no HCI events will be received.
Intel Bluetooth devices that boot up in bootloader mode can not
be used as generic HCI devices, but their HCI transport is still
valuable and so bring that up as raw-only devices.
The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID
1a2c:0023 does not seem to be handling the reports initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel
when connected, and a delay before its initialization. This patch adds the
quirk for this device, which causes the delay to disappear.
[jkosina@suse.cz: remove superfluous comment and fix ordering] Signed-off-by: Daniel Kamil Kozar <dkk089@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Set disconnected flag in struct usbhid when a usb device is removed. Check for
disconnected flag before sending urb requests. This prevents a kernel panic
when a hid driver calls hid_hw_request() after removing a usb device.
projects / thirdparty / kernel / stable.git / log
