Drop the open-coded sched_clock() function and replace it by the provided
GENERIC_SCHED_CLOCK implementation. We have seen quite some hung tasks in the
past, which seem to be fixed by this patch.
We have the insn 0x43ffff80 in IIR but from IAOQ we should have: 4025d150: 0f f3 20 df ldd,s r19(r31),r31 4025d154: 0f 9f 00 9c ldw r31(ret0),ret0 4025d158: bf 80 20 58 cmpb,*<> r0,ret0,4025d18c <irq_exit+0xcc>
Cpu0 has just completed running parisc_setup_cache_timing:
[ 2.429981] Releasing cpu 1 now, hpa=fffffffffffa2000
[ 2.635751] CPU(s): 2 out of 2 PA8500 (PCX-W) at 440.000000 MHz online
[ 2.726692] Setting cache flush threshold to 1024 kB
[ 2.729932] Not-handled unaligned insn 0x43ffff80
[ 2.798114] Setting TLB flush threshold to 140 kB
[ 2.928039] Unaligned handler failed, ret = -1
From the backtrace, cpu1 is in smp_callin:
void __init smp_callin(void)
{
int slave_id = cpu_now_booting;
smp_cpu_init(slave_id);
preempt_disable();
flush_cache_all_local(); /* start with known state */
flush_tlb_all_local(NULL);
local_irq_enable(); /* Interrupts have been off until now */
cpu_startup_entry(CPUHP_AP_ONLINE_IDLE);
So, it has just flushed its caches and the TLB. It would seem either the
flushes in parisc_setup_cache_timing or smp_callin have corrupted kernel
memory.
The attached patch reworks parisc_setup_cache_timing to remove the races
in setting the cache and TLB flush thresholds. It also corrects the
number of bytes flushed in the TLB calculation.
The patch flushes the cache and TLB on cpu0 before starting the
secondary processors so that they are started from a known state.
Tested with a few reboots on c8000.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3105f234e0aba43e44e277c20f9b32ee8add43d4 replaced module
cpu id table with a cpu feature check, which is logically correct.
But we need the module device table to allow module auto loading.
Fixes:3105f234 thermal/powerclamp: correct cpu support check Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vince Weaver reported that perf_fuzzer + KASAN detects that PEBS event
unwinds sometimes do 'weird' things. In particular, we seemed to be
ending up unwinding from random places on the NMI stack.
While it was somewhat expected that the event record BP,SP would not
match the interrupt BP,SP in that the interrupt is strictly later than
the record event, it was overlooked that it could be on an already
overwritten stack.
Therefore, don't copy the recorded BP,SP over the interrupted BP,SP
when we need stack unwinds.
Note that its still possible the unwind doesn't full match the actual
event, as its entirely possible to have done an (I)RET between record
and interrupt, but on average it should still point in the general
direction of where the event came from. Also, it's the best we can do,
considering.
The particular scenario that triggered the bogus NMI stack unwind was
a PEBS event with very short period, upon enabling the event at the
tail of the PMI handler (FREEZE_ON_PMI is not used), it instantly
triggers a record (while still on the NMI stack) which in turn
triggers the next PMI. This then causes back-to-back NMIs and we'll
try and unwind the stack-frame from the last NMI, which obviously is
now overwritten by our own.
The token table passed into match_token() must be null-terminated, which
it currently is not in the perf's address filter string parser, as caught
by Vince's perf_fuzzer and KASAN.
It doesn't blow up otherwise because of the alignment padding of the table
to the next element in the .rodata, which is luck.
Fixing by adding a null-terminator to the token table.
Reported-by: Vince Weaver <vincent.weaver@maine.edu> Tested-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dvyukov@google.com Fixes: 375637bc524 ("perf/core: Introduce address range filtering") Link: http://lkml.kernel.org/r/877f81f264.fsf@ashishki-desk.ger.corp.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the 80486 DX, it seems that some exceptions may leave garbage in
the high bits of CS. This causes sporadic failures in which
early_fixup_exception() refuses to fix up an exception.
As far as I can tell, this has been buggy for a long time, but the
problem seems to have been exacerbated by commits:
1e02ce4cccdc ("x86: Store a per-cpu shadow copy of CR4") e1bfc11c5a6f ("x86/init: Fix cr4_init_shadow() on CR4-less machines")
This appears to have broken for as long as we've had early
exception handling.
[ Note to stable maintainers: This patch is needed all the way back to 3.4,
but it will only apply to 4.6 and up, as it depends on commit:
0e861fbb5bda ("x86/head: Move early exception panic code into early_fixup_exception()")
If you want to backport to kernels before 4.6, please don't backport the
prerequisites (there was a big chain of them that rewrote a lot of the
early exception machinery); instead, ask me and I can send you a one-liner
that will apply. ]
Reported-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 4c5023a3fa2e ("x86-32: Handle exception table entries during early boot") Link: http://lkml.kernel.org/r/cb32c69920e58a1a58e7b5cad975038a69c0ce7d.1479609510.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert O'Callahan reported that after an execve PTRACE_GETREGSET
NT_X86_XSTATE continues to return the pre-exec register values
until the exec'ed task modifies FPU state.
A correct bugfix introduced a harmless warning that shows up with gcc-7:
fs/nfs/callback.c: In function 'nfs_callback_up':
fs/nfs/callback.c:214:14: error: array subscript is outside array bounds [-Werror=array-bounds]
What happens here is that the 'minorversion == 0' check tells the
compiler that we assume minorversion can be something other than 0,
but when CONFIG_NFS_V4_1 is disabled that would be invalid and
result in an out-of-bounds access.
The added check for IS_ENABLED(CONFIG_NFS_V4_1) tells gcc that this
really can't happen, which makes the code slightly smaller and also
avoids the warning.
The bugfix that introduced the warning is marked for stable backports,
we want this one backported to the same releases.
Fixes: 98b0f80c2396 ("NFSv4.x: Fix a refcount leak in nfs_callback_up_net") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a policy replacement, the task cred may be out of date and need
to be updated. However change_hat is using the stale profiles from
the out of date cred resulting in either: a stale profile being applied
or, incorrect failure when searching for a hat profile as it has been
migrated to the new parent profile.
Fixes: 01e2b670aa898a39259bc85c78e3d74820f4d3b6 (failure to find hat) Fixes: 898127c34ec03291c86f4ff3856d79e9e18952bc (stale policy being applied)
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1000287 Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to make scanning consume almost arbitrary amounts
of memory, e.g. by sending beacon frames with random BSSIDs at
high rates while somebody is scanning.
Limit the number of BSS table entries we're willing to cache to
1000, limiting maximum memory usage to maybe 4-5MB, but lower
in practice - that would be the case for having both full-sized
beacon and probe response frames for each entry; this seems not
possible in practice, so a limit of 1000 entries will likely be
closer to 0.5 MB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For large values of "mult" and long uptimes, the intermediate
result of "cycles * mult" can overflow 64 bits. For example,
the tile platform calls clocksource_cyc2ns with a 1.2 GHz clock;
we have mult = 853, and after 208.5 days, we overflow 64 bits.
Since clocksource_cyc2ns() is intended to be used for relative
cycle counts, not absolute cycle counts, performance is more
importance than accepting a wider range of cycle values. So,
just use mult_frac() directly in tile's sched_clock().
Commit 4cecf6d401a0 ("sched, x86: Avoid unnecessary overflow
in sched_clock") by Salman Qazi results in essentially the same
generated code for x86 as this change does for tile. In fact,
a follow-on change by Salman introduced mult_frac() and switched
to using it, so the C code was largely identical at that point too.
Peter Zijlstra then added mul_u64_u32_shr() and switched x86
to use it. This is, in principle, better; by optimizing the
64x64->64 multiplies to be 32x32->64 multiplies we can potentially
save some time. However, the compiler piplines the 64x64->64
multiplies pretty well, and the conditional branch in the generic
mul_u64_u32_shr() causes some bubbles in execution, with the
result that it's pretty much a wash. If tilegx provided its own
implementation of mul_u64_u32_shr() without the conditional branch,
we could potentially save 3 cycles, but that seems like small gain
for a fair amount of additional build scaffolding; no other platform
currently provides a mul_u64_u32_shr() override, and tile doesn't
currently have an <asm/div64.h> header to put the override in.
Additionally, gcc currently has an optimization bug that prevents
it from recognizing the opportunity to use a 32x32->64 multiply,
and so the result would be no better than the existing mult_frac()
until such time as the compiler is fixed.
For now, just using mult_frac() seems like the right answer.
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a work around for a bug with LSI Fusion MPT SAS2 when perfoming
secure erase. Due to the very long time the operation takes, commands
issued during the erase will time out and will trigger execution of the
abort hook. Even though the abort hook is called for the specific
command which timed out, this leads to entire device halt
(scsi_state terminated) and premature termination of the secure erase.
Set device state to busy while ATA passthrough commands are in progress.
[mkp: hand applied to 4.9/scsi-fixes, tweaked patch description]
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com> Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Cc: <linux-scsi@vger.kernel.org> Cc: Sathya Prakash <sathya.prakash@broadcom.com> Cc: Chaitra P B <chaitra.basappa@broadcom.com> Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some code (all error handling) submits CDBs that are allocated
on the stack. This breaks with CB/CBI code that tries to create
URB directly from SCSI command buffer - which happens to be in
vmalloced memory with vmalloced kernel stacks.
Let's make copy of the command in usb_stor_CB_transport.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the TI CC3200 LaunchPad board, which uses a
custom USB vendor ID and product ID. Channel A is used for JTAG, and
channel B is used for a UART.
Signed-off-by: Doug Brown <doug@schmorgal.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BRIM Brothers Zone DPMX is a bicycle powermeter. This ID is for the USB
serial interface in its charging dock for the control pods, via which some
settings for the pods can be modified.
Signed-off-by: Paul Jakma <paul@jakma.org> Cc: Barry Redmond <barry@brimbrothers.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split irqchip allows pic and ioapic routes to be used without them being
created, which results in NULL access. Check for NULL and avoid it.
(The setup is too racy for a nicer solutions.)
em_jmp_far and em_ret_far assumed that setting IP can only fail in 64
bit mode, but syzkaller proved otherwise (and SDM agrees).
Code segment was restored upon failure, but it was left uninitialized
outside of long mode, which could lead to a leak of host kernel stack.
We could have fixed that by always saving and restoring the CS, but we
take a simpler approach and just break any guest that manages to fail
as the error recovery is error-prone and modern CPUs don't need emulator
for this.
Found by syzkaller:
WARNING: CPU: 2 PID: 3668 at arch/x86/kvm/emulate.c:2217 em_ret_far+0x428/0x480
Kernel panic - not syncing: panic_on_warn set ...
Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far jumps") Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cluster xAPIC delivery incorrectly assumed that dest_id <= 0xff.
With enabled KVM_X2APIC_API_USE_32BIT_IDS in KVM_CAP_X2APIC_API, a
userspace can send an interrupt with dest_id that results in
out-of-bounds access.
The VT-d specification (§8.3.3) says:
‘Virtual Functions’ of a ‘Physical Function’ are under the scope
of the same remapping unit as the ‘Physical Function’.
The BIOS is not required to list all the possible VFs in the scope
tables, and arguably *shouldn't* make any attempt to do so, since there
could be a huge number of them.
This has been broken basically for ever — the VF is never going to match
against a specific unit's scope, so it ends up being assigned to the
INCLUDE_ALL IOMMU. Which was always actually correct by coincidence, but
now we're looking at Root-Complex integrated devices with SR-IOV support
it's going to start being wrong.
Fix it to simply use pci_physfn() before doing the lookup for PCI devices.
Somehow I ended up with an off-by-three error in calculating the size of
the PASID and PASID State tables, which triggers allocations failures as
those tables unfortunately have to be physically contiguous.
In fact, even the *correct* maximum size of 8MiB is problematic and is
wont to lead to allocation failures. Since I have extracted a promise
that this *will* be fixed in hardware, I'm happy to limit it on the
current hardware to a maximum of 0x20000 PASIDs, which gives us 1MiB
tables — still not ideal, but better than before.
Reported by Mika Kuoppala <mika.kuoppala@linux.intel.com> and also by
Xunlei Pang <xlpang@redhat.com> who submitted a simpler patch to fix
only the allocation (and not the free) to the "correct" limit... which
was still problematic.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gpiod_set_array_value_complex does not clear the bits field.
Therefore when the drivers set_multiple funciton is called bits outside
the mask are undefined and can be either set or not. So bank_val needs
to be masked with bank_mask before or with the reg_val cache.
Need to ensure that reg_output is not updated while setting multiple
bits. This makes the mutex locking behaviour for the set_multiple call
consistent with that of the set_value call.
With HZ=100 element timeout in dynamic sets (i.e. flow tables) is 10 times
higher than configured.
Add proper conversion to/from jiffies, when interacting with userspace.
I tested this on Linux 4.8.1, and it applies cleanly to current nf and
nf-next trees.
Fixes: 22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates") Signed-off-by: Anders K. Pedersen <akp@cohaesio.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is a CM id object that has port assigned to it, it means that
the cm-id asked for the specific port that it should go by it, but if
that port was removed (hot-unplug event) the cm-id was not updated.
In order to fix that the port keeps a list of all the cm-id's that are
planning to go by it, whenever the port is removed it marks all of them
as invalid.
This commit fixes a kernel panic which happens when running traffic between
guests and we force reboot a guest mid traffic, it triggers a kernel panic:
sg_alloc_table gets unsigned int as parameter while the driver
returns it as size_t. Check npages isn't greater than maximum
unsigned int.
Fixes: eeb8461e36c9 ("IB: Refactor umem to use linear SG table") Signed-off-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an internal error condition is detected, make sure to set the
device inactive after dispatching the event so ULPs can get a
notification of this event.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating kernel CQs use 128B CQE stride if the
cache line size is 128B, 64B otherwise. This prevents
multiple CQEs from residing in a 128B cache line,
which can cause retries when there are concurrent
read and writes in one cache line.
Tested with IPoIB on PPC64, saw ~5% throughput
improvement.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RXE resets the send-q only once in rxe_qp_init_req() when
QP is created, but when the QP is reused after QP reset, the send-q
holds previous garbage data.
This garbage data wrongly fails CQEs that otherwise
should have completed successfully.
Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com> Reviewed-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To correctly handle a erroneous WR this fix does the following
1. Make sure the bad WQE causes a user completion event.
2. Call rxe_completer to handle the erred WQE.
Before the fix, when rxe_requester found a bad WQE, it changed its
status to IB_WC_LOC_PROT_ERR and exit with 0 for non RC QPs.
If this was the 1st WQE then there would be no ACK to invoke the
completer and this bad WQE would be stuck in the QP's send-q.
On top of that the requester exiting with 0 caused rxe_do_task to
endlessly invoke rxe_requester, resulting in a soft-lockup attached
below.
In case the WQE was not the 1st and rxe_completer did get a chance to
handle the bad WQE, it did not cause a complete event since the WQE's
IB_SEND_SIGNALED flag was not set.
Setting WQE status to IB_SEND_SIGNALED is subject to IBA spec
version 1.2.1, section 10.7.3.1 Signaled Completions.
Markus reported that there's a weird behavior on perf top --hierarchy
regarding the column length.
Looking at the code, I found a dubious code which affects the symptoms.
When --hierarchy option is used, the last column length might be
inaccurate since it skips to update the length on leaf entries.
I cannot remember why it did and looks like a leftover from previous
version during the development.
Anyway, updating the column length often is not harmful. So let's move
the code out.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 1a3906a7e6b9 ("perf hists: Resort hist entries with hierarchy") Link: http://lkml.kernel.org/r/20161108130833.9263-5-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider two devices, A and B, where B is a child of A, and B utilizes
asynchronous suspend (it does not matter whether A is sync or async). If
B fails to suspend_noirq() or suspend_late(), or is interrupted by a
wakeup (pm_wakeup_pending()), then it aborts and sets the async_error
variable. However, device A does not (immediately) check the async_error
variable; it may continue to run its own suspend_noirq()/suspend_late()
callback. This is bad.
We can resolve this problem by doing our error and wakeup checking
(particularly, for the async_error flag) after waiting for children to
suspend, instead of before. This also helps align the logic for the noirq and
late suspend cases with the logic in __device_suspend().
It's easy to observe this erroneous behavior by, for example, forcing a
device to sleep a bit in its suspend_noirq() (to ensure the parent is
waiting for the child to complete), then return an error, and watch the
parent suspend_noirq() still get called. (Or similarly, fake a wakeup
event at the right (or is it wrong?) time.)
Fixes: de377b397272 (PM / sleep: Asynchronous threads for suspend_late) Fixes: 28b6fd6e3779 (PM / sleep: Asynchronous threads for suspend_noirq) Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the reference taken by class_find_device() after
opening the RTC device.
Fixes: 77437fd4e61f (pm: boot time suspend selftest) Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This subsystem consistently fails to drop the device reference taken by
class_find_device().
Note that some of these lookup functions already take a reference to the
returned data, while others claim no reference is needed (or does not
seem need one).
Fixes: 183b9b592a62 ("uwb: add the UWB stack (core files)") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Scott Mayhew <smayhew@redhat.com> Fixes: c3d4879e ("sunrpc: Add a function to close temporary transports immediately") Reviewed-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba996302 ("mfd: add platform_device sharing support for mfd") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we sync the RX queues the driver waits to receive echo
notification on all the RX queues.
The wait queue is set with timeout until all queues have received
the notification.
However, iwl_mvm_rx_queue_notif() never woke up the wait queue,
with the result of the counter value being checked only when the
timeout expired.
This may cause a latency of up to 1 second.
When a unified D0/D3 image is used, we don't restart the FW in the
D0->D3->D0 transitions. Therefore, the d3_test functionality should
not call ieee8021_restart_hw() when the resuming either.
Fixes: commit 23ae61282b88 ("iwlwifi: mvm: Do not switch to D3 image on suspend") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With unified images, we need to make sure the net-detect scan is
stopped after resuming, since we don't restart the FW. Also, we need
to make sure we check if there are enough scan slots available to run
it, as we do with other scans.
Fixes: commit 23ae61282b88 ("iwlwifi: mvm: Do not switch to D3 image on suspend") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emmanuel reports that when CMD_WANT_ASYNC_CALLBACK is used by mvm,
the callback will be called with the command queue lock held, and
mvm will try to stop all (other) TX queues, which acquires their
locks - this caused a false lockdep recursive locking report.
Suppress this report by marking the command queue lock with a new,
separate, lock class so lockdep can tell the difference between
the two types of queues.
Fixes: 156f92f2b471 ("iwlwifi: block the queues when we send ADD_STA for uAPSD") Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPLC data parsing is too restrictive and was not trying find the
correct element for WiFi. This causes problems with some BIOSes where
the SPLC method exists, but doesn't have a WiFi entry on the first
element of the list. The domain type values are also incorrect
according to the specification.
Fix this by complying with the actual specification.
Additionally, replace all occurrences of SPLX to SPLC, since SPLX is
only a structure internal to the ACPI tables, and may not even exist.
Fixes: bcb079a14d75 ("iwlwifi: pcie: retrieve and parse ACPI power limitations") Reported-by: Chris Rorvick <chris@rorvick.com> Tested-by: Paul Bolle <pebolle@tiscali.nl> Tested-by: Chris Rorvick <chris@rorvick.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RTC can be clocked from an external 32KHz oscillator, or from the
Peripheral PLL. The RTC has an internal oscillator buffer to support
direct operation with a crystal.
The RTC functional clock is sourced by default from the clock derived
from the Peripheral PLL. In order to select source as external osc clk
the following changes needs to be done:
- Enable the RTC OSC (RTC_OSC_REG[4]OSC32K_GZ = 0)
- Enable the clock mux(RTC_OSC_REG[6]K32CLK_EN = 1)
- Select the external clock source (RTC_OSC_REG[3]32KCLK_SEL = 1)
Since 'parent_rate * mfn' may overflow 32 bits, the result should be
stored using 64 bits.
The problem was discovered when trying to set the rate of the audio PLL
(pll4_post_div) on an i.MX6Q. The desired rate was 196.608 MHz, but
the actual rate returned was 192.000570 MHz. The round rate function should
have been able to return 196.608 MHz, i.e., the desired rate.
Virtio 1.0 spec says VIRTIO_F_ANY_LAYOUT and VIRTIO_NET_F_GSO are
legacy-only feature bits. Do not negotiate them in virtio 1 mode. Note
this is a spec violation so we need to backport it to stable/downstream
kernels.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My heuristic for detecting type 1 DVI DP++ adaptors based on the VBT
port information apparently didn't survive the reality of buggy VBTs.
In this particular case we have a machine with a natice HDMI port, but
the VBT tells us it's a DP++ port based on its capabilities.
The dvo_port information in VBT does claim that we're dealing with a
HDMI port though, but we have other machines which do the same even
when they actually have DP++ ports. So that piece of information alone
isn't sufficient to tell the two apart.
After staring at a bunch of VBTs from various machines, I have to
conclude that the only other semi-reliable clue we can use is the
presence of the AUX channel in the VBT. On this particular machine
AUX channel is specified as zero, whereas on some of the other machines
which listed the DP++ port as HDMI have a non-zero AUX channel.
I've also seen VBTs which have dvo_port a DP but have a zero AUX
channel. I believe those we need to treat as DP ports, so we'll limit
the AUX channel check to just the cases where dvo_port is HDMI.
If we encounter any more serious failures with this heuristic I think
we'll have to have to throw it out entirely. But that could mean that
there is a risk of type 1 DVI dongle users getting greeted by a
black screen, so I'd rather not go there unless absolutely necessary.
v2: Remove the duplicate PORT_A check (Daniel)
Fix some typos in the commit message
Cc: Daniel Otero <daniel.otero@outlook.com> Tested-by: Daniel Otero <daniel.otero@outlook.com> Fixes: d61992565bd3 ("drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97994 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1478884464-14251-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 7a17995a3dc8613f778a9e2fd20e870f17789544) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once we've determined that the sink is MST capable we never end up
running through the full detect cycle again, despite getting HPDs.
Fix tht by ripping out the incorrect piece of code responsible.
This got broken when I moved the long HPD handling to the ->detect()
hook, but failed to remove the leftover code.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Cc: drm-intel-fixes@lists.freedesktop.org Cc: Rui Tiago Matos <tiagomatos@gmail.com> Tested-by: Rui Tiago Matos <tiagomatos@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98323 Cc: Kirill A. Shutemov <kirill@shutemov.name> Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
References: https://bugs.freedesktop.org/show_bug.cgi?id=98306 Fixes: 1015811609c0 ("drm/i915: Move long hpd handling into the hotplug work") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1477057478-29328-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 1aab956c7b8872fb6976328316bfad62c6e67cf8) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
External clients which import our bo's wait only
for exclusive dmabuf-fences, not on shared ones,
ditto for bo's which we import from external
providers and write to.
Therefore attach exclusive fences on prime shared buffers
if our exported buffer gets imported by an external
client, or if we import a buffer from an external
exporter.
See discussion in thread:
https://lists.freedesktop.org/archives/dri-devel/2016-October/122370.html
Prime export tested on Intel iGPU + AMD Tonga dGPU as
DRI3/Present Prime render offload, and with the Tonga
standalone as primary gpu.
v2: Add a wait for all shared fences before prime export,
as suggested by Christian Koenig.
v3: - Mark buffer prime_exported in amdgpu_gem_prime_pin,
so we only use the exclusive fence when exporting a
bo to external clients like a separate iGPU, but not
when exporting/importing from/to ourselves as part of
regular DRI3 fd passing.
- Propagate failure of reservation_object_wait_rcu back
to caller.
v4: - Switch to a prime_shared_count counter instead of a
flag, which gets in/decremented on prime_pin/unpin, so
we can switch back to shared fences if all clients
detach from our exported bo.
- Also switch to exclusive fence for prime imported bo's.
v5: - Drop lret, instead use int ret -> long ret, as proposed
by Christian.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95472 Tested-by: Mike Lothian <mike@fireburn.co.uk> (v1) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com>. Cc: Christian König <christian.koenig@amd.com> Cc: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d3cbff1b5 "powerpc: Put exception configuration in a common place"
broke the setting of the AIL bit (which enables taking exceptions with
the MMU still on) on all processors, moving it incorrectly to a function
called only on the boot CPU. This was correct for the guest case but
not when running in hypervisor mode.
This fixes it by partially reverting that commit, putting the setting
back in cpu_ready_for_interrupts()
Fixes: d3cbff1b5a90 ("powerpc: Put exception configuration in a common place") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using AES-XTS on a Wandboard, we receive a Mode error:
caam_jr 2102000.jr1: 20001311: CCB: desc idx 19: AES: Mode error.
According to the Security Reference Manual, the Low Power AES units
of the i.MX6 do not support the XTS mode. Therefore we must not
register XTS implementations in the Crypto API.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: c6415a6016bf "crypto: caam - add support for acipher xts(aes)" Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since commit fa93fd4ecc9c ("regulator: core: Ensure we are at least in
bounds for our constraints") the imx53-qsb board populated with a Dialog
DA9053 PMIC fails to boot:
The LDO3 voltage constraints passed in the device tree do not match
the valid range according to the datasheet, so fix this accordingly to
allow the board booting again.
While at it, fix the other voltage constraints as well.
If the block size or cluster size is insane, reject the mount. This
is important for security reasons (although we shouldn't be just
depending on this check).
So Sebastian turned off the PIE for kernel builds but that was too late
- Kbuild.include already uses KBUILD_CFLAGS and trying to disable gcc
options with, say cc-disable-warning, fails:
gcc -D__KERNEL__ -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs
...
-Wno-sign-compare -fno-asynchronous-unwind-tables -Wframe-address -c -x c /dev/null -o .31392.tmp
/dev/null:1:0: error: code model kernel does not support PIC mode
because that returns an error and we can't disable the warning. For
example in this case:
which leads to gcc issuing all those warnings again.
So let's turn off PIE/PIC at the earliest possible moment, when we
declare KBUILD_CFLAGS so that cc-disable-warning picks it up too.
Also, we need the $(call cc-option ...) because -fno-PIE is supported
since gcc v3.4 and our lowest supported gcc version is 3.2 right now.
Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the gcc is configured to do -fPIE by default then the build aborts
later with:
| Unsupported relocation type: unknown type rel type name (29)
Tagging it stable so it is possible to compile recent stable kernels as
well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding -no-PIE to the fstack protector check. -no-PIE was introduced
before -fstack-protector so there is no need for a runtime check.
Without it the build stops:
|Cannot use CONFIG_CC_STACKPROTECTOR_STRONG: -fstack-protector-strong available but compiler is broken
due to -mcmodel=kernel + -fPIE if -fPIE is enabled by default.
Tagging it stable so it is possible to compile recent stable kernels as
well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Debian started to build the gcc with -fPIE by default so the kernel
build ends before it starts properly with:
|kernel/bounds.c:1:0: error: code model kernel does not support PIC mode
Also add to KBUILD_AFLAGS due to:
|gcc -Wp,-MD,arch/x86/entry/vdso/vdso32/.note.o.d … -mfentry -DCC_USING_FENTRY … vdso/vdso32/note.S
|arch/x86/entry/vdso/vdso32/note.S:1:0: sorry, unimplemented: -mfentry isn’t supported for 32-bit in combination with -fpic
Tagging it stable so it is possible to compile recent stable kernels as
well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This affectively reverts commit 377ccbb48373 ("Makefile: Mute warning
for __builtin_return_address(>0) for tracing only") because it turns out
that it really isn't tracing only - it's all over the tree.
We already also had the warning disabled separately for mm/usercopy.c
(which this commit also removes), and it turns out that we will also
want to disable it for get_lock_parent_ip(), that is used for at least
TRACE_IRQFLAGS. Which (when enabled) ends up being all over the tree.
Steven Rostedt had a patch that tried to limit it to just the config
options that actually triggered this, but quite frankly, the extra
complexity and abstraction just isn't worth it. We have never actually
had a case where the warning is actually useful, so let's just disable
it globally and not worry about it.
Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deselect functionality can be ignored for device-trees with
"i2c-mux-idle-disconnect" entries if no platform_data is available.
By enabling the deselect functionality outside the platform_data
block the logic works as it did in previous kernels.
Fixes: 7fcac9807175 ("i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core") Signed-off-by: Alex Hemme <ahemme@cisco.com> Signed-off-by: Ziyang Wu <ziywu@cisco.com>
[touched up a few minor issues /peda] Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that the I2C mux core code depends on HAS_IOMEM
for historical reasons, while CONFIG_I2C_MUX_REG does *not*
have a direct dependency on HAS_IOMEM.
This creates a situation where a allyesconfig or allmodconfig
for UM Linux will select I2C_MUX, and will implicitly enable
I2C_MUX_REG as well, and the compilation will fail for the
register driver.
Fix this up by making I2C_MUX_REG depend on HAS_IOMEM and
removing the dependency from I2C_MUX.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Jonathan Cameron <jic23@jic23.retrosnub.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jonathan Cameron <jic23@kernel.org> Acked-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit [1a3f099101b8: ALSA: hda - Fix surround output pins for
ASRock B150M mobo] introduced a fixup of pin configs for ASRock
mobos to fix the surround outputs. However, this overrides the pin
configs of the mic pins as if they are outputs-only, effectively
disabling the mic inputs. Of course, it's a regression wrt mic
functionality.
Actually the pins 0x18 and 0x1a don't need to be changed; we just need
to disable the bogus pins 0x14 and 0x15. Then the auto-parser will
pick up mic pins as switchable and assign the surround outputs there.
This patch removes the incorrect pin overrides of NID 0x18 and 0x1a
from the ASRock fixup.
The usb-audio driver implements the deferred device disconnection for
the device in use. In this mode, the disconnection callback returns
immediately while the actual ALSA card object removal happens later
when all files get closed. As Shuah reported, this code flow,
however, leads to a use-after-free, detected by KASAN:
It's the code trying to clear drvdata of the assigned usb_device where
the usb_device itself was already released in usb_release_dev() after
the disconnect callback.
This patch fixes it by checking whether the code path is via the
disconnect callback, i.e. chip->shutdown flag is set.
When locking a GPIO line as IRQ, we go to lengths to
double-check that the line is really set as input before
marking it as used for IRQ. This is not good on GPIO chips
that can sleep, because this function is called in IRQ-safe
context. Just skip this if it can't be checked quickly.
Currently this happens on sleeping expanders such as STMPE
or TC3589x:
BUG: scheduling while atomic: swapper/1/0x00000002
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.9.0-rc1+ #38
Hardware name: Nomadik STn8815
[<c000f2e0>] (unwind_backtrace) from [<c000d244>] (show_stack+0x10/0x14)
[<c000d244>] (show_stack) from [<c0037b78>] (__schedule_bug+0x54/0x80)
[<c0037b78>] (__schedule_bug) from [<c042df14>] (__schedule+0x3a0/0x460)
[<c042df14>] (__schedule) from [<c042e028>] (schedule+0x54/0xb8)
(...)
This patch fixes that problem and relies on the direction
read from the chip when it was added.
Fixes: 9c10280d85c1 ("gpio: flush direction status in gpiochip_lock_as_irq()") Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov reported an issue with proc_register in bcm.c.
As suggested by Cong Wang this patch adds a lock_sock() protection and
a check for unsuccessful proc_create_data() in bcm_connect().
This caused a regression on the STMP2401 on the Nomadik
NHK8815:
stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x43 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x44 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
It turns out that we start to poll for the reset bit to
go low again too quickly: the STMPE2401 is not yet online and
ready to be asked for the status of the RESET bit.
By introducing a 10ms delay before starting to hammer
the register for information, we get back to normal:
Commit 41a3da2b8e163 ("mfd: intel-lpss: Save register context on
suspend") saved the register context while going to suspend and
also put the device in reset state.
Due to the resetting of device, system cannot enter S3/S0ix
states when no_console_suspend flag is enabled. The system
and serial console both hang. The resetting of device is not
needed while going to suspend. Hence remove this code.
Fixes: 41a3da2b8e163 ("mfd: intel-lpss: Save register context on suspend") Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial code for rdmavt carried with it a restriction that was a
vestige from the qib driver, that to dma map a page it had to be less
than a page size. This is not the case on modern hardware, both qib and
hfi1 will be just fine with unaligned map requests.
This fixes a 4.8 regression where by an IPoIB transfer of > PAGE_SIZE
will hang because the dma map page call always fails. This was
introduced after commit 5faba5469522 ("IB/ipoib: Report SG feature
regardless of HW UD CSUM capability") added the capability to use SG by
default. Rather than override this, the HW supports it, so allow SG.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The type flags in the irq descriptor are there for historical reasons and
only updated via irq_modify_status() or irq_set_type(). Both functions also
update the type flags in irqdata. __setup_irq() is the only left over user
of the type flags in the irq descriptor.
If __setup_irq() is called with empty irq type flags, then the type flags
are retrieved from irqdata. If an interrupt is shared, then the type flags
are compared with the type flags stored in the irq descriptor.
On x86 the ioapic does not have a irq_set_type() callback because the type
is defined in the BIOS tables and cannot be changed. The type is stored in
irqdata at setup time without updating the type data in the irq
descriptor. As a result the comparison described above fails.
There is no point in updating the irq descriptor flags because the only
relevant storage is irqdata. Use the type flags from irqdata for both
retrieval and comparison in __setup_irq() instead.
Aside of that the print out in case of non matching type flags has the old
and new type flags arguments flipped. Fix that as well.
For correctness sake the flags stored in the irq descriptor should be
removed, but this is beyond the scope of this bugfix and will be done in a
later patch.
Fixes: 4b357daed698 ("genirq: Look-up trigger type if not specified by caller") Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Jon Hunter <jonathanh@nvidia.com> Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1611072020360.3501@nanos Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a module is first loaded and its function ip records are added to the
ftrace list of functions to modify, they are set to DISABLED, as their text
is still in a read only state. When the module is fully loaded, and can be
updated, the flag is cleared, and if their's any functions that should be
tracing them, it is updated at that moment.
But there's several locations that do record accounting and should ignore
records that are marked as disabled, or they can cause issues.
Alexei already fixed one location, but others need to be addressed.
Fixes: b7ffffbb46f2 "ftrace: Add infrastructure for delayed enabling of module functions" Reported-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftrace_shutdown() checks for sanity of ftrace records
and if dyn_ftrace->flags is not zero, it will warn.
It can happen that 'flags' are set to FTRACE_FL_DISABLED at this point,
since some module was loaded, but before ftrace_module_enable()
cleared the flags for this module.
In other words the module.c is doing:
ftrace_module_init(mod); // calls ftrace_update_code() that sets flags=FTRACE_FL_DISABLED
... // here ftrace_shutdown() is called that warns, since
err = prepare_coming_module(mod); // didn't have a chance to clear FTRACE_FL_DISABLED
Fix it by ignoring disabled records.
It's similar to what __ftrace_hash_rec_update() is already doing.
Link: http://lkml.kernel.org/r/1478560460-3818619-1-git-send-email-ast@fb.com Fixes: b7ffffbb46f2 "ftrace: Add infrastructure for delayed enabling of module functions" Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM calls kvm_pmu_set_counter_event_type() when PMCCFILTR is configured.
But this function can't deals with PMCCFILTR correctly because the evtCount
bits of PMCCFILTR, which is reserved 0, conflits with the SW_INCR event
type of other PMXEVTYPER<n> registers. To fix it, when eventsel == 0, this
function shouldn't return immediately; instead it needs to check further
if select_idx is ARMV8_PMU_CYCLE_IDX.
Another issue is that KVM shouldn't copy the eventsel bits of PMCCFILTER
blindly to attr.config. Instead it ought to convert the request to the
"cpu cycle" event type (i.e. 0x11).
To support this patch and to prevent duplicated definitions, a limited
set of ARMv8 perf event types were relocated from perf_event.c to
asm/perf_event.h.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Wei Huang <wei@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function user_notifier_unregister should be called only once for each
registered user notifier.
Function kvm_arch_hardware_disable can be executed from an IPI context
which could cause a race condition with a VCPU returning to user mode
and attempting to unregister the notifier.
cpu_llc_id (Last Level Cache ID) derivation on AMD Fam17h has an
underflow bug when extracting the socket_id value. It starts from 0
so subtracting 1 from it will result in an invalid value. This breaks
scheduling topology later on since the cpu_llc_id will be incorrect.
For example, the the cpu_llc_id of the *other* CPU in the loops in
set_cpu_sibling_map() underflows and we're generating the funniest
thread_siblings masks and then when I run 8 threads of nbench, they get
spread around the LLC domains in a very strange pattern which doesn't
give you the normal scheduling spread one would expect for performance.
Other things like EDAC use cpu_llc_id so they will be b0rked too.
So, the APIC ID is preset in APICx020 for bits 3 and above: they contain
the core complex, node and socket IDs.
The LLC is at the core complex level so we can find a unique cpu_llc_id
by right shifting the APICID by 3 because then the least significant bit
will be the Core Complex ID.
Tested-by: Borislav Petkov <bp@suse.de> Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
[ Cleaned up and extended the commit message. ] Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 3849e91f571d ("x86/AMD: Fix last level cache topology for AMD Fam17h systems") Link: http://lkml.kernel.org/r/20161108083506.rvqb5h4chrcptj7d@pd.tnic Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ffs_func_eps_disable is called from atomic context so it cannot sleep
thus cannot grab a mutex. Change the handling of epfile->read_buffer
to use non-sleeping synchronisation method.
Reported-by: Chen Yu <chenyu56@huawei.com> Signed-off-by: Michał Nazarewicz <mina86@mina86.com> Fixes: 9353afbbfa7b ("buffer data from ‘oversized’ OUT requests") Tested-by: John Stultz <john.stultz@linaro.org> Tested-by: Chen Yu <chenyu56@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all of the user copy routines are converted to return
accurate residual lengths when an exception occurs, we no longer need
the broken fixup routines.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
