We submitted the command with TARGET_SCF_ACK_KREF, which requires
acknowledgment of command completion. If the command fails, make sure to
decrement the ref count.
Fix 3 typos in 8703b driver. 2 typos in calibration routines are not
fatal and do not seem to have any impact, just fix them to match vendor
driver.
However the last one in rtw8703b_set_channel_bb() clears too many bits
in REG_OFDM0_TX_PSD_NOISE, causing TX and RX issues (neither rate goes
above MCS0-MCS1). Vendor driver clears only 2 most significant bits.
With the last typo fixed, the driver is able to reach MCS7 on Pinebook
Due to a limitation in available memory, the MT7916 firmware can only
handle either 5 GHz or 6 GHz at a time. It does not support runtime
switching without a full restart.
On older firmware, this accidentally worked to some degree due to missing
checks, but couldn't be supported properly, because it left the 6 GHz
channels uncalibrated.
Newer firmware refuses to start on either band if the passed EEPROM
data indicates support for both.
Deal with this limitation by using a module parameter to specify the
preferred band in case both are supported.
This is the equivalent of commit 28818b4d871b ("wifi: rtw88: usb: Fix
disconnection after beacon loss") for SDIO chips.
Tested on Pinephone (RTL8723CS), random disconnections became rare,
instead of a frequent nuisance.
Since brcmf_get_ip() can and actually will return NULL in this case the
call to brcmf_txfinalize() will result in a NULL pointer dereference inside
brcmf_txfinalize() when trying to update ifp->ndev->stats.tx_errors.
This will only happen if a flowring still has an skb.
Although the NULL pointer dereference has only been seen when trying to
update the tx statistic, all other uses of the ifp pointer have been
guarded as well with an early return if ifp is NULL.
RTL8821AE is stuck transmitting at the lowest rate allowed by the rate
mask. This is because the firmware doesn't know the device is connected
to a network.
Fix the macros SET_H2CCMD_MSRRPT_PARM_OPMODE and
SET_H2CCMD_MSRRPT_PARM_MACID_IND to work on the first byte of __cmd,
not the second. Now the firmware is correctly notified when the device
is connected to a network and it activates the rate control.
raw_spin_locks can be traced by lockdep or tracing itself. Atomic64
operations can be used in the tracing infrastructure. When an architecture
does not have true atomic64 operations it can use the generic version that
disables interrupts and uses spin_locks.
The tracing ring buffer code uses atomic64 operations for the time
keeping. But because some architectures use the default operations, the
locking inside the atomic operations can cause an infinite recursion.
As atomic64 implementation is architecture specific, it should not be
using raw_spin_locks() but instead arch_spin_locks as that is the purpose
of arch_spin_locks. To be used in architecture specific implementations of
generic infrastructure like atomic64 operations.
Note, by switching from raw_spin_locks to arch_spin_locks, the locks taken
to emulate the atomic64 operations will not have lockdep, mmio, or any
kind of checks done on them. They will not even disable preemption,
although the code will disable interrupts preventing the tasks that hold
the locks from being preempted. As the locks held are done so for very
short periods of time, and the logic is only done to emulate atomic64, not
having them be instrumented should not be an issue.
Cc: stable@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andreas Larsson <andreas@gaisler.com> Link: https://lore.kernel.org/20250122144311.64392baf@gandalf.local.home Fixes: c84897c0ff592 ("ring-buffer: Remove 32bit timestamp logic") Closes: https://lore.kernel.org/all/86fb4f86-a0e4-45a2-a2df-3154acc4f086@gaisler.com/ Reported-by: Ludwig Rydberg <ludwig.rydberg@gaisler.com> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some architectures can not safely do atomic64 operations in NMI context.
Since the ring buffer relies on atomic64 operations to do its time
keeping, if an event is requested in NMI context, reject it for these
architectures.
Cc: stable@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andreas Larsson <andreas@gaisler.com> Link: https://lore.kernel.org/20250120235721.407068250@goodmis.org Fixes: c84897c0ff592 ("ring-buffer: Remove 32bit timestamp logic") Closes: https://lore.kernel.org/all/86fb4f86-a0e4-45a2-a2df-3154acc4f086@gaisler.com/ Reported-by: Ludwig Rydberg <ludwig.rydberg@gaisler.com> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hid-sensor-hub creates the individual device structs and transfers them
to the created mfd platform-devices via the platform_data in the mfd_cell.
Before e651a1da442a ("HID: hid-sensor-hub: Allow parallel synchronous reads")
the sensor-hub was managing access centrally, with one "completion" in the
hub's data structure, which needed to be finished on removal at the latest.
The mentioned commit then moved this central management to each hid sensor
device, resulting on a completion in each struct hid_sensor_hub_device.
The remove procedure was adapted to go through all sensor devices and
finish any pending "completion".
What this didn't take into account was, platform_device_add_data() that is
used by mfd_add{_hotplug}_devices() does a kmemdup on the submitted
platform-data. So the data the platform-device gets is a copy of the
original data, meaning that the device worked on a different completion
than what sensor_hub_remove() currently wants to access.
To fix that, use device_for_each_child() to go through each child-device
similar to how mfd_remove_devices() unregisters the devices later and
with that get the live platform_data to finalize the correct completion.
Without remove hook to clear wake irq, there will be kernel dump when
doing module test.
"bbnsm_pwrkey 44440000.bbnsm:pwrkey: wake irq already initialized"
Add remove hook to clear wake irq and set wakeup to false.
"resource->end" needs to always be equal to "resource->start + size - 1".
The previous version of the function did not perform the "- 1" in case
of an empty resource.
Also make sure to allow an empty resource at address 0.
According to the UFS Device Specification, the dExtendedUFSFeaturesSupport
defines the support for TOO_HIGH_TEMPERATURE as bit[4] and the
TOO_LOW_TEMPERATURE as bit[5]. Correct the code to match with
the UFS device specification definition.
Cc: stable@vger.kernel.org Fixes: e88e2d32200a ("scsi: ufs: core: Probe for temperature notification support") Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com> Link: https://lore.kernel.org/r/69992b3e3e3434a5c7643be5a64de48be892ca46.1736793068.git.quic_nguyenb@quicinc.com Reviewed-by: Avri Altman <Avri.Altman@wdc.com> Reviewed-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison function cmpworker() violates the C standard's
requirements for qsort() comparison functions, which mandate symmetry
and transitivity:
Symmetry: If x < y, then y > x.
Transitivity: If x < y and y < z, then x < z.
In its current implementation, cmpworker() incorrectly returns 0 when
w1->tid < w2->tid, which breaks both symmetry and transitivity. This
violation causes undefined behavior, potentially leading to issues such
as memory corruption in glibc [1].
Fix the issue by returning -1 when w1->tid < w2->tid, ensuring
compliance with the C standard and preventing undefined behavior.
GCC 15 changed the default C standard version to C23, which should not
have impacted the kernel because it requests the gnu11 standard via
'-std=' in the main Makefile. However, the EFI libstub Makefile uses its
own set of KBUILD_CFLAGS for x86 without a '-std=' value (i.e., using
the default), resulting in errors from the kernel's definitions of bool,
true, and false in stddef.h, which are reserved keywords under C23.
./include/linux/stddef.h:11:9: error: expected identifier before ‘false’
11 | false = 0,
./include/linux/types.h:35:33: error: two or more data types in declaration specifiers
35 | typedef _Bool bool;
Set '-std=gnu11' in the x86 cflags to resolve the error and consistently
use the same C standard version for the entire kernel. All other
architectures reuse KBUILD_CFLAGS from the rest of the kernel, so this
issue is not visible for them.
blkcg_fill_root_iostats() iterates over @block_class's devices by
class_dev_iter_(init|next)(), but does not end iterating with
class_dev_iter_exit(), so causes the class's subsystem refcount leakage.
Fix by ending the iterating with class_dev_iter_exit().
Fixes: ef45fe470e1e ("blk-cgroup: show global disk stats in root cgroup io.stat") Reviewed-by: Michal Koutný <mkoutny@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20250105-class_fix-v6-2-3a2f1768d4d4@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching uretprobes to processes running inside docker, the attached
process is segfaulted when encountering the retprobe.
The reason is that now that uretprobe is a system call the default seccomp
filters in docker block it as they only allow a specific set of known
syscalls. This is true for other userspace applications which use seccomp
to control their syscall surface.
Since uretprobe is a "kernel implementation detail" system call which is
not used by userspace application code directly, it is impractical and
there's very little point in forcing all userspace applications to
explicitly allow it in order to avoid crashing tracked processes.
Pass this systemcall through seccomp without depending on configuration.
Note: uretprobe is currently only x86_64 and isn't expected to ever be
supported in i386.
Some of the audio subsystem clocks defined in clk-mt2701.h aren't
actually used by the driver. This broke conversion to
mtk_clk_simple_probe which expects that the highest possible clk id is
defined by the ARRAY_SIZE.
Add additional dummy clocks to fill the gaps and remain compatible with
the existing DT bindings.
Fixes: 0f69a423c458 ("clk: mediatek: Switch to mtk_clk_simple_probe() where possible") Cc: stable@vger.kernel.org Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/a07584d803af57b9ce4b5df5e122c09bf5a56ac9.1734300668.git.daniel@makrotopia.org Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 973d1607d936 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to
simplify driver") broke DT bindings as the highest index was reduced by
1 because the id count starts from 1 and not from 0.
Fix this, like for other drivers which had the same issue, by adding a
dummy clk at index 0.
Fixes: 973d1607d936 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to simplify driver") Cc: stable@vger.kernel.org Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/b126a5577f3667ef19b1b5feea5e70174084fb03.1734300668.git.daniel@makrotopia.org Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
Add the parent_map property for the clock where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
Add the parent_map property for two clocks where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.8 Fixes: c58225b7e3d7 ("clk: qcom: add the SM8650 Global Clock Controller driver, part 1") Reported-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8650 Link: https://lore.kernel.org/r/20241219170011.70140-2-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.2 Fixes: 955f2ea3b9e9 ("clk: qcom: Add GCC driver for SM8550") Reported-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8550 Link: https://lore.kernel.org/r/20241219170011.70140-1-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c45ae598fc16 ("clk: qcom: support for alpha mode configuration")
added support for configuring alpha mode, but it seems that the feature
was never working in practice.
The value of the alpha_{en,mode}_mask members of the configuration gets
added to the value parameter passed to the regmap_update_bits() function,
however the same values are not getting applied to the bitmask. As the
result, the respective bits in the USER_CTL register are never modifed
which leads to improper configuration of several PLLs.
The following table shows the PLL configurations where the 'alpha_en_mask'
member is set and which are passed as a parameter for the
clk_alpha_pll_configure() function. In the table the 'expected rate' column
shows the rate the PLL should run at with the given configuration, and
the 'real rate' column shows the rate the PLL runs at actually. The real
rates has been verified on hardwareOn IPQ* platforms, on other platforms,
those are computed values only.
As it can be seen from the above, there are several PLLs which are
configured incorrectly.
Change the code to apply both 'alpha_en_mask' and 'alpha_mode_mask'
values to the bitmask in order to configure the alpha mode correctly.
Applying the 'alpha_en_mask' fixes the initial rate of the PLLs showed
in the table above. Since the 'alpha_mode_mask' is not used by any driver
currently, that part of the change causes no functional changes.
Setting the genpd's struct device's name with dev_set_name() is
happening within pm_genpd_init(). If it remains NULL, things can blow up
later, such as when crafting the devfs hierarchy for the power domain:
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
...
Call trace:
strlen from start_creating+0x90/0x138
start_creating from debugfs_create_dir+0x20/0x178
debugfs_create_dir from genpd_debug_add.part.0+0x4c/0x144
genpd_debug_add.part.0 from genpd_debug_init+0x74/0x90
genpd_debug_init from do_one_initcall+0x5c/0x244
do_one_initcall from kernel_init_freeable+0x19c/0x1f4
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x28
Bisecting tracks this crash back to commit 899f44531fe6 ("pmdomain: core:
Add GENPD_FLAG_DEV_NAME_FW flag"), which exchanges use of genpd->name
with dev_name(&genpd->dev) in genpd_debug_add.part().
While testing the MMC nodes proposed in [1], it was noted that mmc0/1
would fail to initialize, with "mmc: fatal err update clk timeout" in
the kernel logs. A closer look at the clock definitions showed that the MMC
MPs had the "CLK_SET_RATE_NO_REPARENT" flag set. No reason was given for
adding this flag in the first place, and its original purpose is unknown,
but it doesn't seem to make sense and results in severe limitations to MMC
speeds. Thus, remove this flag from the 3 MMC MPs.
With vmalloc stack addresses enabled (CONFIG_VMAP_STACK=y) DCP trusted
keys can crash during en- and decryption of the blob encryption key via
the DCP crypto driver. This is caused by improperly using sg_init_one()
with vmalloc'd stack buffers (plain_key_blob).
Fix this by always using kmalloc() for buffers we give to the DCP crypto
driver.
Cc: stable@vger.kernel.org # v6.10+ Fixes: 0e28bf61a5f9 ("KEYS: trusted: dcp: fix leak of blob encryption key") Signed-off-by: David Gstir <david@sigma-star.at> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the possible ways to enable the input MTU auto-selection for L2CAP
connections is supposed to be through passing a special "0" value for it
as a socket option. Commit [1] added one of those into avdtp. However, it
simply wouldn't work because the kernel still treats the specified value
as invalid and denies the setting attempt. Recorded BlueZ logs include the
following:
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4b6e228e297b ("Bluetooth: Auto tune if input MTU is set to 0") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A NULL sock pointer is passed into l2cap_sock_alloc() when it is called
from l2cap_sock_new_connection_cb() and the error handling paths should
also be aware of it.
Seemingly a more elegant solution would be to swap bt_sock_alloc() and
l2cap_chan_create() calls since they are not interdependent to that moment
but then l2cap_chan_create() adds the soon to be deallocated and still
dummy-initialized channel to the global list accessible by many L2CAP
paths. The channel would be removed from the list in short period of time
but be a bit more straight-forward here and just check for NULL instead of
changing the order of function calls.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 7c4f78cdb8e7 ("Bluetooth: L2CAP: do not leave dangling sk pointer on error in l2cap_sock_create()") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
When the system powers up eDP with external monitors in seamless boot
sequence, stutter get enabled before TTU and HUBP registers being
programmed, which resulting in underflow.
[HOW]
Enable TTU in hubp_init.
Change the sequence that do not perpare_bandwidth and optimize_bandwidth
while having seamless boot streams.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Lo-an Chen <lo-an.chen@amd.com> Signed-off-by: Paul Hsieh <paul.hsieh@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I'm seeing underruns with these 64bpp YUV formats on TGL.
The weird details:
- only happens on pipe B/C/D SDR planes, pipe A SDR planes
seem fine, as do all HDR planes
- somehow CDCLK related, higher CDCLK allows for bigger plane
with these formats without underruns. With 300MHz CDCLK I
can only go up to 1200 pixels wide or so, with 650MHz even
a 3840 pixel wide plane was OK
- ICL and ADL so far appear unaffected
So not really sure what's the deal with this, but bspec does
state "64-bit formats supported only on the HDR planes" so
let's just drop these formats from the SDR planes. We already
disallow 64bpp RGB formats.
Commit 1c56e9a39833 ("drm/i915/dp: Get optimal link config to have best
compressed bpp") tries to find the best compressed bpp for the
link. However, it iterates from max to min bpp on display 13+, and from
min to max on other platforms. This presumably leads to minimum
compressed bpp always being chosen on display 11-12.
Iterate from high to low on all platforms to actually use the best
possible compressed bpp.
Fixes: 1c56e9a39833 ("drm/i915/dp: Get optimal link config to have best compressed bpp") Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: <stable@vger.kernel.org> # v6.7+ Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/3bba67923cbcd13a59d26ef5fa4bb042b13c8a9b.1738327620.git.jani.nikula@intel.com
(cherry picked from commit 56b0337d429356c3b9ecc36a03023c8cc856b196) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having the exec queue snapshot inside a "GuC CT" section was always
wrong. Commit c28fd6c358db ("drm/xe/devcoredump: Improve section
headings and add tile info") tried to fix that bug, but with that also
broke the mesa tool that parses the devcoredump, hence it was reverted
in commit a53da2fb25a3 ("drm/xe: Revert some changes that break a mesa
debug tool").
With the mesa tool also fixed, this can propagate as a fix on both
kernel and userspace side to avoid unnecessary headache for a debug
feature.
Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Julia Filipchuk <julia.filipchuk@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: stable@vger.kernel.org Fixes: a53da2fb25a3 ("drm/xe: Revert some changes that break a mesa debug tool") Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250123051112.1938193-2-lucas.demarchi@intel.com Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit a37934ea75d331fafa7fe80b6180642ba5193422) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When converting to folios the cleanup path of shmem_get_pages() was
missed. When a DMA remap fails and the max segment size is greater than
PAGE_SIZE it will attempt to retry the remap with a PAGE_SIZEd segment
size. The cleanup code isn't properly using the folio apis and as a
result isn't handling compound pages correctly.
v2 -> v3:
(Ville) Just use shmem_sg_free_table() as-is in the failure path of
shmem_get_pages(). shmem_sg_free_table() will clear mapping unevictable
but it will be reset when it retries in shmem_sg_alloc_table().
v1 -> v2:
(Ville) Fixed locations where we were not clearing mapping unevictable.
After the context is unpinned the backing memory can also be unpinned,
so any accesses via the lrc_reg_state pointer can end up in unmapped
memory. To avoid that, make sure to only access that memory if the
context is pinned when printing its info.
v2: fix newline alignment
Fixes: 28ff6520a34d ("drm/i915/guc: Update GuC debugfs to support new GuC") Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Cc: <stable@vger.kernel.org> # v5.15+ Reviewed-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250115001334.3875347-1-daniele.ceraolospurio@intel.com
(cherry picked from commit 5bea40687c5cf2a33bf04e9110eb2e2b80222ef5) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a2b5a9956269 ("drm/amd/display: Use HW lock mgr for PSR1")
Because it may cause system hang while connect with two edp panel.
Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of halt_if_hws_hang is to preserve GPU state for driver
debugging when queue preemption fails. Issuing per-queue reset may
kill wavefronts which caused the preemption failure.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com> Reviewed-by: Jonathan Kim <Jonathan.Kim@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 6.12.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following page fault was observed duringthe KFD process release.
In this particular error case, the HIP test (./MemcpyPerformance -h)
does not require the queue. As a result, the process_context_addr was
not assigned when the KFD process was released, ultimately leading to
this page fault during the execution of the function
kfd_process_dequeue_from_all_devices().
[why]
Updating the cursor enablement register can be a slow operation and accumulates
when high polling rate cursors cause frequent updates asynchronously to the
cursor position.
[how]
Since the cursor enable bit is cached there is no need to update the
enablement register if there is no change to it. This removes the
read-modify-write from the cursor position programming path in HUBP and
DPP, leaving only the register writes.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Sung Lee <sung.lee@amd.com> Signed-off-by: Aric Cyr <Aric.Cyr@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 32bit systems the addition operations in ipc_msg_alloc() can
potentially overflow leading to memory corruption.
Add bounds checking using KSMBD_IPC_MAX_PAYLOAD to avoid overflow.
Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We try to reuse the same vsie page when re-executing the vsie with a
given SCB address. The result is that we use the same shadow SCB --
residing in the vsie page -- and can avoid flushing the TLB when
re-running the vsie on a CPU.
So, when we allocate a fresh vsie page, or when we reuse a vsie page for
a different SCB address -- reusing the shadow SCB in different context --
we set ihcpu=0xffff to trigger the flush.
However, after we looked up the SCB address in the radix tree, but before
we grabbed the vsie page by raising the refcount to 2, someone could reuse
the vsie page for a different SCB address, adjusting page->index and the
radix tree. In that case, we would be reusing the vsie page with a
wrong page->index.
Another corner case is that we might set the SCB address for a vsie
page, but fail the insertion into the radix tree. Whoever would reuse
that page would remove the corresponding radix tree entry -- which might
now be a valid entry pointing at another page, resulting in the wrong
vsie page getting removed from the radix tree.
Let's handle such races better, by validating that the SCB address of a
vsie page didn't change after we grabbed it (not reuse for a different
SCB; the alternative would be performing another tree lookup), and by
setting the SCB address to invalid until the insertion in the tree
succeeded (SCB addresses are aligned to 512, so ULONG_MAX is invalid).
These scenarios are rare, the effects a bit unclear, and these issues were
only found by code inspection. Let's CC stable to be safe.
Fixes: a3508fbe9dc6 ("KVM: s390: vsie: initial support for nested virtualization") Cc: stable@vger.kernel.org Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Christoph Schlameuss <schlameuss@linux.ibm.com> Tested-by: Christoph Schlameuss <schlameuss@linux.ibm.com>
Message-ID: <20250107154344.1003072-2-david@redhat.com> Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some libraries want to ensure they are single threaded before forking,
so making the kernel's kvm huge page recovery process a vhost task of
the user process breaks those. The minijail library used by crosvm is
one such affected application.
Defer the task to after the first VM_RUN call, which occurs after the
parent process has forked all its jailed processes. This needs to happen
only once for the kvm instance, so introduce some general-purpose
infrastructure for that, too. It's similar in concept to pthread_once;
except it is actually usable, because the callback takes a parameter.
Cc: Sean Christopherson <seanjc@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Tested-by: Alyssa Ross <hi@alyssa.is> Signed-off-by: Keith Busch <kbusch@kernel.org>
Message-ID: <20250123153543.2769928-1-kbusch@meta.com>
[Move call_once API to include/linux. - Paolo] Cc: stable@vger.kernel.org Fixes: d96c77bd4eeb ("KVM: x86: switch hugepage recovery thread to vhost_task") Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly verify the target vCPU is fully online _prior_ to clamping the
index in kvm_get_vcpu(). If the index is "bad", the nospec clamping will
generate '0', i.e. KVM will return vCPU0 instead of NULL.
In practice, the bug is unlikely to cause problems, as it will only come
into play if userspace or the guest is buggy or misbehaving, e.g. KVM may
send interrupts to vCPU0 instead of dropping them on the floor.
However, returning vCPU0 when it shouldn't exist per online_vcpus is
problematic now that KVM uses an xarray for the vCPUs array, as KVM needs
to insert into the xarray before publishing the vCPU to userspace (see
commit c5b077549136 ("KVM: Convert the kvm->vcpus array to a xarray")),
i.e. before vCPU creation is guaranteed to succeed.
As a result, incorrectly providing access to vCPU0 will trigger a
use-after-free if vCPU0 is dereferenced and kvm_vm_ioctl_create_vcpu()
bails out of vCPU creation due to an error and frees vCPU0. Commit afb2acb2e3a3 ("KVM: Fix vcpu_array[0] races") papered over that issue, but
in doing so introduced an unsolvable teardown conundrum. Preventing
accesses to vCPU0 before it's fully online will allow reverting commit afb2acb2e3a3, without re-introducing the vcpu_array[0] UAF race.
Fixes: 1d487e9bf8ba ("KVM: fix spectrev1 gadgets") Cc: stable@vger.kernel.org Cc: Will Deacon <will@kernel.org> Cc: Michal Luczaj <mhal@rbox.co> Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com> Acked-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20241009150455.1057573-2-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's no longer practical for the OMAP IOMMU driver to trick
arm_setup_iommu_dma_ops() into ignoring its presence, so let's use the
same tactic as other IOMMU API users on 32-bit ARM and explicitly kick
the arch code's dma_iommu_mapping out of the way to avoid problems.
During mass manufacturing, we noticed the mmc_rx_crc_error counter,
as reported by "ethtool -S eth0 | grep mmc_rx_crc_error", to increase
above zero during nuttcp speedtests. Most of the time, this did not
affect the achieved speed, but it prompted this investigation.
Cycling through the rx_delay range on six boards (see table below) of
various ages shows that there is a large good region from 0x12 to 0x35
where we see zero crc errors on all tested boards.
The old rx_delay value (0x10) seems to have always been on the edge for
the KSZ9031RNX that is usually placed on Puma.
Choose "rx_delay = 0x23" to put us smack in the middle of the good
region. This works fine as well with the KSZ9131RNX PHY that was used
for a small number of boards during the COVID chip shortages.
Board S/N PHY rx_delay good region
--------- --- --------------------
Puma TT0069903 KSZ9031RNX 0x11 0x35
Puma TT0157733 KSZ9031RNX 0x11 0x35
Puma TT0681551 KSZ9031RNX 0x12 0x37
Puma TT0681156 KSZ9031RNX 0x10 0x38
Puma 17496030079 KSZ9031RNX 0x10 0x37 (Puma v1.2 from 2017)
Puma TT0681720 KSZ9131RNX 0x02 0x39 (alternative PHY used in very few boards)
Intersection of good regions = 0x12 0x35
Middle of good region = 0x23
The code for detecting and updating the connector status in
cdn_dp_pd_event_work() has a number of problems.
- It does not aquire the locks to call the detect helper and update
the connector status. These are struct drm_mode_config.connection_mutex
and struct drm_mode_config.mutex.
- It does not use drm_helper_probe_detect(), which helps with the
details of locking and detection.
- It uses the connector's status field to determine a change to
the connector status. The epoch_counter field is the correct one. The
field signals a change even if the connector status' value did not
change.
Replace the code with a call to drm_connector_helper_hpd_irq_event(),
which fixes all these problems.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Fixes: 81632df69772 ("drm/rockchip: cdn-dp: do not use drm_helper_hpd_irq_event") Cc: Chris Zhong <zyw@rock-chips.com> Cc: Guenter Roeck <groeck@chromium.org> Cc: Sandy Huang <hjc@rock-chips.com> Cc: "Heiko Stübner" <heiko@sntech.de> Cc: Andy Yan <andy.yan@rock-chips.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20241105133848.480407-1-tzimmermann@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When updating the interrupt state for an emulated timer, we return
early and skip the setup of a soft timer that runs in parallel
with the guest.
While this is OK if we have set the interrupt pending, it is pretty
wrong if the guest moved CVAL into the future. In that case,
no timer is armed and the guest can wait for a very long time
(it will take a full put/load cycle for the situation to resolve).
This is specially visible with EDK2 running at EL2, but still
using the EL1 virtual timer, which in that case is fully emulated.
Any key-press takes ages to be captured, as there is no UART
interrupt and EDK2 relies on polling from a timer...
The fix is simply to drop the early return. If the timer interrupt
is pending, we will still return early, and otherwise arm the soft
timer.
Fixes: 4d74ecfa6458b ("KVM: arm64: Don't arm a hrtimer for an already pending timer") Cc: stable@vger.kernel.org Tested-by: Dmytro Terletskyi <dmytro_terletskyi@epam.com> Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20250204110050.150560-2-maz@kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, LPA2 kernel support implies support for up to 52 bits of
physical addressing, and this is reflected in global definitions such as
PHYS_MASK_SHIFT and MAX_PHYSMEM_BITS.
This is potentially problematic, given that LPA2 hardware support is
modeled as a CPU feature which can be overridden, and with LPA2 hardware
support turned off, attempting to map physical regions with address bits
[51:48] set (which may exist on LPA2 capable systems booting with
arm64.nolva) will result in corrupted mappings with a truncated output
address and bogus shareability attributes.
This means that the accepted physical address range in the mapping
routines should be at most 48 bits wide when LPA2 support is configured
but not enabled at runtime.
Fixes: 352b0395b505 ("arm64: Enable 52-bit virtual addressing for 4k and 16k granule configs") Cc: stable@vger.kernel.org Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20241212081841.2168124-9-ardb+git@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 892f7237b3ff ("arm64: Delay initialisation of
cpuinfo_arm64::reg_{zcr,smcr}") we moved access to ZCR, SMCR and SMIDR
later in the boot process in order to ensure that we don't attempt to
interact with them if SVE or SME is disabled on the command line.
Unfortunately when initialising the boot CPU in init_cpu_features() we work
on a copy of the struct cpuinfo_arm64 for the boot CPU used only during
boot, not the percpu copy used by the sysfs code. The expectation of the
feature identification code was that the ID registers would be read in
__cpuinfo_store_cpu() and the values not modified by init_cpu_features().
The main reason for the original change was to avoid early accesses to
ZCR on practical systems that were seen shipping with SVE reported in ID
registers but traps enabled at EL3 and handled as fatal errors, SME was
rolled in due to the similarity with SVE. Since then we have removed the
early accesses to ZCR and SMCR in commits:
abef0695f9665c3d ("arm64/sve: Remove ZCR pseudo register from cpufeature code") 391208485c3ad50f ("arm64/sve: Remove SMCR pseudo register from cpufeature code")
so only the SMIDR_EL1 part of the change remains. Since SMIDR_EL1 is
only trapped via FEAT_IDST and not the SME trap it is less likely to be
affected by similar issues, and the factors that lead to issues with SVE
are less likely to apply to SME.
Since we have not yet seen practical SME systems that need to use a
command line override (and are only just beginning to see SME systems at
all) and the ID register read is much more likely to be safe let's just
store SMIDR_EL1 along with all the other ID register reads in
__cpuinfo_store_cpu().
This issue wasn't apparent when testing on emulated platforms that do not
report values in SMIDR_EL1.
Fixes: 892f7237b3ff ("arm64: Delay initialisation of cpuinfo_arm64::reg_{zcr,smcr}") Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20241217-arm64-fix-boot-cpu-smidr-v3-1-7be278a85623@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When FEAT_LPA{,2} are not implemented, the ID_AA64MMFR0_EL1.PARange and
TCR.IPS values corresponding with 52-bit physical addressing are
reserved.
Setting the TCR.IPS field to 0b110 (52-bit physical addressing) has side
effects, such as how the TTBRn_ELx.BADDR fields are interpreted, and so
it is important that disabling FEAT_LPA2 (by overriding the
ID_AA64MMFR0.TGran fields) also presents a PARange field consistent with
that.
So limit the field to 48 bits unless LPA2 is enabled, and update
existing references to use the override consistently.
Fixes: 352b0395b505 ("arm64: Enable 52-bit virtual addressing for 4k and 16k granule configs") Cc: stable@vger.kernel.org Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20241212081841.2168124-10-ardb+git@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the host stage1 is configured for LPA2, the value currently being
programmed into TCR_EL2.T0SZ may be invalid unless LPA2 is configured
at HYP as well. This means kvm_lpa2_is_enabled() is not the right
condition to test when setting TCR_EL2.DS, as it will return false if
LPA2 is only available for stage 1 but not for stage 2.
Similary, programming TCR_EL2.PS based on a limited IPA range due to
lack of stage2 LPA2 support could potentially result in problems.
So use lpa2_is_enabled() instead, and set the PS field according to the
host's IPS, which is capped at 48 bits if LPA2 support is absent or
disabled. Whether or not we can make meaningful use of such a
configuration is a different question.
Cc: stable@vger.kernel.org Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20241212081841.2168124-11-ardb+git@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore PCI state after putting the NPU in D0.
Restoring state before powering up the device caused a Qemu crash
if NPU was running in passthrough mode and recovery was performed.
Most of these sizes and counts are capped at 256MB so the math doesn't
result in an integer overflow. The "relocs" count needs to be checked
as well. Otherwise on 32bit systems the calculation of "full_data"
could be wrong.
The field "eip" (instruction pointer) and "esp" (stack pointer) of a task
can be read from /proc/PID/stat. These fields can be interesting for
coredump.
However, these fields were disabled by commit 0a1eb2d474ed ("fs/proc: Stop
reporting eip and esp in /proc/PID/stat"), because it is generally unsafe
to do so. But it is safe for a coredumping process, and therefore
exceptions were made:
- for a coredumping thread by commit fd7d56270b52 ("fs/proc: Report
eip/esp in /prod/PID/stat for coredumping").
- for all other threads in a coredumping process by commit cb8f381f1613
("fs/proc/array.c: allow reporting eip/esp for all coredumping
threads").
The above two commits check the PF_DUMPCORE flag to determine a coredump thread
and the PF_EXITING flag for the other threads.
Unfortunately, commit 92307383082d ("coredump: Don't perform any cleanups
before dumping core") moved coredump to happen earlier and before PF_EXITING is
set. Thus, checking PF_EXITING is no longer the correct way to determine
threads in a coredumping process.
Instead of PF_EXITING, use PF_POSTCOREDUMP to determine the other threads.
Checking of PF_EXITING was added for coredumping, so it probably can now be
removed. But it doesn't hurt to keep.
Fixes: 92307383082d ("coredump: Don't perform any cleanups before dumping core") Cc: stable@vger.kernel.org Cc: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Kees Cook <kees@kernel.org> Signed-off-by: Nam Cao <namcao@linutronix.de> Link: https://lore.kernel.org/r/d89af63d478d6c64cc46a01420b46fd6eb147d6f.1735805772.git.namcao@linutronix.de Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Including m68k's <asm/raw_io.h> in vga.h on nommu platforms results
in conflicting defines with io_no.h for various I/O macros from the
__raw_read and __raw_write families. An example error is
In file included from arch/m68k/include/asm/vga.h:12,
from include/video/vga.h:22,
from include/linux/vgaarb.h:34,
from drivers/video/aperture.c:12:
>> arch/m68k/include/asm/raw_io.h:39: warning: "__raw_readb" redefined
39 | #define __raw_readb in_8
|
In file included from arch/m68k/include/asm/io.h:6,
from include/linux/io.h:13,
from include/linux/irq.h:20,
from include/asm-generic/hardirq.h:17,
from ./arch/m68k/include/generated/asm/hardirq.h:1,
from include/linux/hardirq.h:11,
from include/linux/interrupt.h:11,
from include/linux/trace_recursion.h:5,
from include/linux/ftrace.h:10,
from include/linux/kprobes.h:28,
from include/linux/kgdb.h:19,
from include/linux/fb.h:6,
from drivers/video/aperture.c:5:
arch/m68k/include/asm/io_no.h:16: note: this is the location of the previous definition
16 | #define __raw_readb(addr) \
|
Include <asm/io.h>, which avoids raw_io.h on nommu platforms.
Also change the defined values of some of the read/write symbols in
vga.h to __raw_read/__raw_write as the raw_in/raw_out symbols are not
generally available.
The hwcaps code that exposes SVE features to userspace only
considers ID_AA64ZFR0_EL1, while this is only valid when
ID_AA64PFR0_EL1.SVE advertises that SVE is actually supported.
The expectations are that when ID_AA64PFR0_EL1.SVE is 0, the
ID_AA64ZFR0_EL1 register is also 0. So far, so good.
Things become a bit more interesting if the HW implements SME.
In this case, a few ID_AA64ZFR0_EL1 fields indicate *SME*
features. And these fields overlap with their SVE interpretations.
But the architecture says that the SME and SVE feature sets must
match, so we're still hunky-dory.
This goes wrong if the HW implements SME, but not SVE. In this
case, we end-up advertising some SVE features to userspace, even
if the HW has none. That's because we never consider whether SVE
is actually implemented. Oh well.
Fix it by restricting all SVE capabilities to ID_AA64PFR0_EL1.SVE
being non-zero. The HWCAPS documentation is amended to reflect the
actually checks performed by the kernel.
Fixes: 06a916feca2b ("arm64: Expose SVE2 features for userspace") Reported-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: stable@vger.kernel.org Reviewed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20250107-arm64-2024-dpisa-v5-1-7578da51fc3d@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
THe md-linear is removed by commit 849d18e27be9 ("md: Remove deprecated
CONFIG_MD_LINEAR") because it has been marked as deprecated for a long
time.
However, md-linear is used widely for underlying disks with different size,
sadly we didn't know this until now, and it's true useful to create
partitions and assemble multiple raid and then append one to the other.
People have to use dm-linear in this case now, however, they will prefer
to minimize the number of involved modules.
Fixes: 849d18e27be9 ("md: Remove deprecated CONFIG_MD_LINEAR") Cc: stable@vger.kernel.org Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Coly Li <colyli@kernel.org> Acked-by: Mike Snitzer <snitzer@kernel.org> Link: https://lore.kernel.org/r/20250102112841.1227111-1-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MS-SMB2 section 2.2.13.2.10 specifies that 'epoch' should be a 16-bit
unsigned integer used to track lease state changes. Change the data
type of all instances of 'epoch' from unsigned int to __u16. This
simplifies the epoch change comparisons and makes the code more
compliant with the protocol spec.
Cc: stable@vger.kernel.org Signed-off-by: Meetakshi Setiya <msetiya@microsoft.com> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tracepoints based on smb3_inf_compound_*_class have tcon id and
session id swapped around. This results in incorrect output in
`trace-cmd report`.
Fix the order of arguments to resolve this issue. The trace-cmd output
below shows the before and after of the smb3_delete_enter and
smb3_delete_done events as an example. The smb3_cmd_* events show the
correct session and tcon id for reference.
Also fix tracepoint set -> get in the SMB2_OP_GET_REPARSE case.
Check if the server honored ATTR_SYSTEM flag by CREATE_OPTION_SPECIAL
option. If not then server does not support ATTR_SYSTEM and newly
created file is not SFU compatible, which means that the call failed.
If CREATE was successful but either setting ATTR_SYSTEM failed or
writing type/data information failed then remove the intermediate
object created by CREATE. Otherwise intermediate empty object stay
on the server.
This ensures that if the creating of SFU files with system attribute is
unsupported by the server then no empty file stay on the server as a result
of unsupported operation.
This is for example case with Samba server and Linux tmpfs storage without
enabled xattr support (where Samba stores ATTR_SYSTEM bit).
Cc: stable@vger.kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I struggle to explain dividing an ARRAY_SIZE() by the size of an element
once again. As the latter equals to 2, only the half of EEPROM was ever
written. Drop the unexplainable division and write full ARRAY_SIZE().
Cc: stable@vger.kernel.org Fixes: 7a8685accb95 ("leds: lp8860: Introduce TI lp8860 4 channel LED driver") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Link: https://lore.kernel.org/r/20241114101402.2562878-1-alexander.sverdlin@siemens.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver generates following warning when regulator support isn't
enabled in the kernel. Fix it.
drivers/cpufreq/s3c64xx-cpufreq.c: In function 's3c64xx_cpufreq_set_target':
>> drivers/cpufreq/s3c64xx-cpufreq.c:55:22: warning: variable 'old_freq' set but not used [-Wunused-but-set-variable]
55 | unsigned int old_freq, new_freq;
| ^~~~~~~~
>> drivers/cpufreq/s3c64xx-cpufreq.c:54:30: warning: variable 'dvfs' set but not used [-Wunused-but-set-variable]
54 | struct s3c64xx_dvfs *dvfs;
| ^~~~
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202501191803.CtfT7b2o-lkp@intel.com/ Cc: 5.4+ <stable@vger.kernel.org> # v5.4+ Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Link: https://patch.msgid.link/236b227e929e5adc04d1e9e7af6845a46c8e9432.1737525916.git.viresh.kumar@linaro.org Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver can be built as a module since commit 3b062a086984 ("cpufreq:
dt-platdev: Support building as module"), but unfortunately this caused
a regression because the cputfreq-dt-platdev.ko module does not autoload.
Usually, this is solved by just using the MODULE_DEVICE_TABLE() macro to
export all the device IDs as module aliases. But this driver is special
due how matches with devices and decides what platform supports.
There are two of_device_id lists, an allow list that are for CPU devices
that always match and a deny list that's for devices that must not match.
The driver registers a cpufreq-dt platform device for all the CPU device
nodes that either are in the allow list or contain an operating-points-v2
property and are not in the deny list.
Enforce builtin compile of cpufreq-dt-platdev to make autoload work.
Fixes: 3b062a086984 ("cpufreq: dt-platdev: Support building as module") Link: https://lore.kernel.org/all/20241104201424.2a42efdd@akair/ Link: https://lore.kernel.org/all/20241119111918.1732531-1-javierm@redhat.com/ Cc: stable@vger.kernel.org Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reported-by: Radu Rendec <rrendec@redhat.com> Reported-by: Javier Martinez Canillas <javierm@redhat.com>
[ Viresh: Picked commit log from Javier, updated tags ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RXRPC_CALL_SERVER_SECURING state doesn't really belong with the other
states in the call's state set as the other states govern the call's Rx/Tx
phase transition and govern when packets can and can't be received or
transmitted. The "Securing" state doesn't actually govern the reception of
packets and would need to be split depending on whether or not we've
received the last packet yet (to mirror RECV_REQUEST/ACK_REQUEST).
The "Securing" state is more about whether or not we can start forwarding
packets to the application as recvmsg will need to decode them and the
decoding can't take place until the challenge/response exchange has
completed.
Fix this by removing the RXRPC_CALL_SERVER_SECURING state from the state
set and, instead, using a flag, RXRPC_CALL_CONN_CHALLENGING, to track
whether or not we can queue the call for reception by recvmsg() or notify
the kernel app that data is ready. In the event that we've already
received all the packets, the connection event handler will poke the app
layer in the appropriate manner.
Also there's a race whereby the app layer sees the last packet before rxrpc
has managed to end the rx phase and change the state to one amenable to
allowing a reply. Fix this by queuing the packet after calling
rxrpc_end_rx_phase().
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org Link: https://patch.msgid.link/20250204230558.712536-2-dhowells@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of tc offload, when user space queries the kernel for tc action
statistics, tc will query the offloaded statistics from device drivers.
Among other statistics, drivers are expected to pass the number of
packets that hit the action since the last query as a 64-bit number.
Unfortunately, tc treats the number of packets as a 32-bit number,
leading to truncation and incorrect statistics when the number of
packets since the last query exceeds 0xffffffff:
$ tc -s filter show dev swp2 ingress
filter protocol all pref 1 flower chain 0
filter protocol all pref 1 flower chain 0 handle 0x1
skip_sw
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device swp1) stolen
index 1 ref 1 bind 1 installed 58 sec used 0 sec
Action statistics:
Sent 1133877034176 bytes 536959475 pkt (dropped 0, overlimits 0 requeues 0)
[...]
According to the above, 2111-byte packets were redirected which is
impossible as only 64-byte packets were transmitted and the MTU was
1500.
Fix by treating packets as a 64-bit number:
$ tc -s filter show dev swp2 ingress
filter protocol all pref 1 flower chain 0
filter protocol all pref 1 flower chain 0 handle 0x1
skip_sw
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device swp1) stolen
index 1 ref 1 bind 1 installed 61 sec used 0 sec
Action statistics:
Sent 1370624380864 bytes 21416005951 pkt (dropped 0, overlimits 0 requeues 0)
[...]
qdisc_tree_reduce_backlog() notifies parent qdisc only if child
qdisc becomes empty, therefore we need to reduce the backlog of the
child qdisc before calling it. Otherwise it would miss the opportunity
to call cops->qlen_notify(), in the case of DRR, it resulted in UAF
since DRR uses ->qlen_notify() to maintain its active list.
Fixes: f8d4bc455047 ("net/sched: netem: account for backlog updates from child qdisc") Cc: Martin Ottens <martin.ottens@fau.de> Reported-by: Mingi Cho <mincho@theori.io> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Link: https://patch.msgid.link/20250204005841.223511-4-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Expected behaviour:
In case we reach scheduler's limit, pfifo_tail_enqueue() will drop a
packet in scheduler's queue and decrease scheduler's qlen by one.
Then, pfifo_tail_enqueue() enqueue new packet and increase
scheduler's qlen by one. Finally, pfifo_tail_enqueue() return
`NET_XMIT_CN` status code.
Weird behaviour:
In case we set `sch->limit == 0` and trigger pfifo_tail_enqueue() on a
scheduler that has no packet, the 'drop a packet' step will do nothing.
This means the scheduler's qlen still has value equal 0.
Then, we continue to enqueue new packet and increase scheduler's qlen by
one. In summary, we can leverage pfifo_tail_enqueue() to increase qlen by
one and return `NET_XMIT_CN` status code.
The problem is:
Let's say we have two qdiscs: Qdisc_A and Qdisc_B.
- Qdisc_A's type must have '->graft()' function to create parent/child relationship.
Let's say Qdisc_A's type is `hfsc`. Enqueue packet to this qdisc will trigger `hfsc_enqueue`.
- Qdisc_B's type is pfifo_head_drop. Enqueue packet to this qdisc will trigger `pfifo_tail_enqueue`.
- Qdisc_B is configured to have `sch->limit == 0`.
- Qdisc_A is configured to route the enqueued's packet to Qdisc_B.
Enqueue packet through Qdisc_A will lead to:
- hfsc_enqueue(Qdisc_A) -> pfifo_tail_enqueue(Qdisc_B)
- Qdisc_B->q.qlen += 1
- pfifo_tail_enqueue() return `NET_XMIT_CN`
- hfsc_enqueue() check for `NET_XMIT_SUCCESS` and see `NET_XMIT_CN` => hfsc_enqueue() don't increase qlen of Qdisc_A.
The whole process lead to a situation where Qdisc_A->q.qlen == 0 and Qdisc_B->q.qlen == 1.
Replace 'hfsc' with other type (for example: 'drr') still lead to the same problem.
This violate the design where parent's qlen should equal to the sum of its childrens'qlen.
Bug impact: This issue can be used for user->kernel privilege escalation when it is reachable.
Fixes: 57dbb2d83d10 ("sched: add head drop fifo queue") Reported-by: Quang Le <quanglex97@gmail.com> Signed-off-by: Quang Le <quanglex97@gmail.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Link: https://patch.msgid.link/20250204005841.223511-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While analysing code for software and OF node for the corner case when
caller asks to read zero items in the supposed to be an array of values
I found that ACPI behaves differently to what OF does, i.e.
1. It returns -EINVAL when caller asks to read zero items from integer
array, while OF returns 0, if no other errors happened.
2. It returns -EINVAL when caller asks to read zero items from string
array, while OF returns -ENODATA, if no other errors happened.
Amend ACPI implementation to follow what OF does.
Fixes: b31384fa5de3 ("Driver core: Unified device properties interface for platform firmware") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://patch.msgid.link/20250203194629.3731895-1-andriy.shevchenko@linux.intel.com
[ rjw: Added empty line after a conditional ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
xen_hypercall_hvm(), which is used when running as a Xen PVH guest at
most only once during early boot, is clobbering %rbx. Depending on
whether the caller relies on %rbx to be preserved across the call or
not, this clobbering might result in an early crash of the system.
This can be avoided by using an already saved register instead of %rbx.
Fixes: b4845bb63838 ("x86/xen: add central hypercall functions") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Firmware deinitialization performs MMIO accesses which are not
necessary if the device has already been removed. In some cases,
these accesses happen via readx_poll_timeout_atomic which ends up
timing out, resulting in a warning at hw_atl2_utils_fw.c:112:
The GPIO drivers with latch interrupt support (typically types starting
with PCAL) have interrupt status registers to determine which particular
inputs have caused an interrupt. Unfortunately there is no atomic
operation to read these registers and clear the interrupt. Clearing the
interrupt is done by reading the input registers.
The code was reading the interrupt status registers, and then reading
the input registers. If an input changed between these two events it was
lost.
The solution in this patch is to revert to the non-latch version of
code, i.e. remembering the previous input status, and looking for the
changes. This system results in no more I2C transfers, so is no slower.
The latch property of the device still means interrupts will still be
noticed if the input changes back to its initial state.
Fixes: 44896beae605 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2") Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20240606033102.2271916-1-mark.tomlinson@alliedtelesis.co.nz Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rxrpc_connection attend queue is never used because conn::attend_link
is never initialised and so is always NULL'd out and thus always appears to
be busy. This requires the following fix:
(1) Fix this the attend queue problem by initialising conn::attend_link.
And, consequently, two further fixes for things masked by the above bug:
(2) Fix rxrpc_input_conn_event() to handle being invoked with a NULL
sk_buff pointer - something that can now happen with the above change.
(3) Fix the RXRPC_SKB_MARK_SERVICE_CONN_SECURED message to carry a pointer
to the connection and a ref on it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org Fixes: f2cce89a074e ("rxrpc: Implement a mechanism to send an event notification to a connection") Link: https://patch.msgid.link/20250203110307.7265-3-dhowells@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit ec6e57beaf8b ("ethtool: rss: don't report key if device
doesn't support it") intended to stop reporting key fields for
additional rss contexts if device has a global hashing key.
Later we added dump support and the filtering wasn't properly
added there. So we end up reporting the key fields in dumps
but not in dos:
The drivers/net/hw/rss_ctx.py selftest catches this when run on
a device with single key, already:
# Check| At /root/./ksft-net-drv/drivers/net/hw/rss_ctx.py, line 381, in test_rss_context_dump:
# Check| ksft_ne(set(data.get('hkey', [1])), {0}, "key is all zero")
# Check failed {0} == {0} key is all zero
not ok 8 rss_ctx.test_rss_context_dump
Fixes: f6122900f4e2 ("ethtool: rss: support dumping RSS contexts") Reviewed-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Joe Damato <jdamato@fastly.com> Link: https://patch.msgid.link/20250201013040.725123-2-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we support Adaptive sync operation mode with dynamic frame
rate, but instead the operation mode with fixed rate is set.
This was initially set correctly in the earlier version of changes but
later got changed, while defining a macro for the same.
Commit 4094871db1d6 ("udp: only do GSO if # of segs > 1") avoided GSO
for small packets. But the kernel currently dismisses GSO requests only
after checking MTU/PMTU on gso_size. This means any packets, regardless
of their payload sizes, could be dropped when PMTU becomes smaller than
requested gso_size. We encountered this issue in production and it
caused a reliability problem that new QUIC connection cannot be
established before PMTU cache expired, while non GSO sockets still
worked fine at the same time.
Ideally, do not check any GSO related constraints when payload size is
smaller than requested gso_size, and return EMSGSIZE instead of EINVAL
on MTU/PMTU check failure to be more specific on the error cause.
Fixes: 4094871db1d6 ("udp: only do GSO if # of segs > 1") Signed-off-by: Yan Zhai <yan@cloudflare.com> Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disable PCIe AER on the tg3 device on system reboot on a limited
list of Dell PowerEdge systems. This prevents a fatal PCIe AER event
on the tg3 device during the ACPI _PTS (prepare to sleep) method for
S5 on those systems. The _PTS is invoked by acpi_enter_sleep_state_prep()
as part of the kernel's reboot sequence as a result of commit 38f34dba806a ("PM: ACPI: reboot: Reinstate S5 for reboot").
There was an earlier fix for this problem by commit 2ca1c94ce0b6
("tg3: Disable tg3 device on system reboot to avoid triggering AER").
But it was discovered that this earlier fix caused a reboot hang
when some Dell PowerEdge servers were booted via ipxe. To address
this reboot hang, the earlier fix was essentially reverted by commit 9fc3bc764334 ("tg3: power down device only on SYSTEM_POWER_OFF").
This re-exposed the tg3 PCIe AER on reboot problem.
This fix is not an ideal solution because the root cause of the AER
is in system firmware. Instead, it's a targeted work-around in the
tg3 driver.
Note also that the PCIe AER must be disabled on the tg3 device even
if the system is configured to use "firmware first" error handling.
V3:
- Fix sparse warning on improper comparison of pdev->current_state
- Adhere to netdev comment style
Fixes: 9fc3bc764334 ("tg3: power down device only on SYSTEM_POWER_OFF") Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
