WARNING: CPU: 0 PID: 3502 at drivers/staging/android/ion/ion-ioctl.c:73 ion_ioctl+0x2db/0x380 drivers/staging/android/ion/ion-ioctl.c:73
Kernel panic - not syncing: panic_on_warn set ...
This is a warning that validation of the ioctl fields failed. This was
deliberately added as a warning to make it very obvious to developers that
something needed to be fixed. In reality, this is overkill and disturbs
fuzzing. Switch to pr_warn for a message instead.
This is a warning about attempting to allocate order > MAX_ORDER. This
is coming from a userspace Ion allocation request. Since userspace is
free to request however much memory it wants (and the kernel is free to
deny its allocation), silence the allocation attempt with __GFP_NOWARN
in case it fails.
Using %rbp as a temporary register breaks frame pointer convention and
breaks stack traces when unwinding from an interrupt in the crypto code.
In twofish-3way, we can't simply replace %rbp with another register
because there are none available. Instead, we use the stack to hold the
values that %rbp, %r11, and %r12 were holding previously. Each of these
values represents the half of the output from the previous Feistel round
that is being passed on unchanged to the following round. They are only
used once per round, when they are exchanged with %rax, %rbx, and %rcx.
As a result, we free up 3 registers (one per block) and can reassign
them so that %rbp is not used, and additionally %r14 and %r15 are not
used so they do not need to be saved/restored.
There may be a small overhead caused by replacing 'xchg REG, REG' with
the needed sequence 'mov MEM, REG; mov REG, MEM; mov REG, REG' once per
round. But, counterintuitively, when I tested "ctr-twofish-3way" on a
Haswell processor, the new version was actually about 2% faster.
(Perhaps 'xchg' is not as well optimized as plain moves.)
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't do anything reasonable in security_bounded_transition() if we
don't have a policy loaded, and in fact we could run into problems
with some of the code inside expecting a policy. Fix these problems
like we do many others in security/selinux/ss/services.c by checking
to see if the policy is loaded (ss_initialized) and returning quickly
if it isn't.
Reported-by: syzbot <syzkaller-bugs@googlegroups.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Reviewed-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot/syzkaller automated tests found a problem in
security_context_to_sid_core() during early boot (before we load the
SELinux policy) where we could potentially feed context strings without
NUL terminators into the strcmp() function.
We already guard against this during normal operation (after the SELinux
policy has been loaded) by making a copy of the context strings and
explicitly adding a NUL terminator to the end. The patch extends this
protection to the early boot case (no loaded policy) by moving the context
copy earlier in security_context_to_sid_core().
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Reviewed-By: William Roberts <william.c.roberts@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid slab to warn about exceeded size, fail early if queue
occupies more than KMALLOC_MAX_SIZE.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com Fixes: 2e0ab8ca83c12 ("ptr_ring: array based FIFO for pointers") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To acquire all modeset locks requires a ww_ctx to be allocated. As this
is the legacy path and the allocation small, to reduce the changes
required (and complex untested error handling) to the legacy drivers, we
simply assume that the allocation succeeds. At present, it relies on the
too-small-to-fail rule, but syzbot found that by injecting a failure
here we would hit the WARN. Document that this allocation must succeed
with __GFP_NOFAIL.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171031115535.15166-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to ensure that tracepoints are registered and unregistered
with the users of them. The existing atomic count isn't enough for
that. Add a lock around the tracepoints, so we serialize access
to them.
This fixes cases where we have multiple users setting up and
tearing down tracepoints, like this:
Now in sctp_setsockopt_maxseg user_frag or frag_point can be set with
val >= 8 and val <= SCTP_MAX_CHUNK_LEN. But both checks are incorrect.
val >= 8 means frag_point can even be less than SCTP_DEFAULT_MINSEGMENT.
Then in sctp_datamsg_from_user(), when it's value is greater than cookie
echo len and trying to bundle with cookie echo chunk, the first_len will
overflow.
The worse case is when it's value is equal as cookie echo len, first_len
becomes 0, it will go into a dead loop for fragment later on. In Hangbin
syzkaller testing env, oom was even triggered due to consecutive memory
allocation in that loop.
Besides, SCTP_MAX_CHUNK_LEN is the max size of the whole chunk, it should
deduct the data header for frag_point or user_frag check.
This patch does a proper check with SCTP_DEFAULT_MINSEGMENT subtracting
the sctphdr and datahdr, SCTP_MAX_CHUNK_LEN subtracting datahdr when
setting frag_point via sockopt. It also improves sctp_setsockopt_maxseg
codes.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported a kernel warning in xfrm_state_fini(), which
indicates that we have entries left in the list
net->xfrm.state_all whose proto is zero. And
xfrm_id_proto_match() doesn't consider them as a match with
IPSEC_PROTO_ANY in this case.
Proto with value 0 is probably not a valid value, at least
verify_newsa_info() doesn't consider it valid either.
This patch fixes it by checking the proto value in
validate_tmpl() and rejecting invalid ones, like what iproute2
does in xfrm_xfrmproto_getbyname().
When we do tunnel or beet mode, we pass saddr and daddr from the
template to xfrm_state_find(), this is ok. On transport mode,
we pass the addresses from the flowi, assuming that the IP
addresses (and address family) don't change during transformation.
This assumption is wrong in the IPv4 mapped IPv6 case, packet
is IPv4 and template is IPv6.
Fix this by catching address family missmatches of the policy
and the flow already before we do the lookup.
Syzbot caught an oops at unregister_shrinker() because combination of
commit 1d3d4437eae1bb29 ("vmscan: per-node deferred work") and fault
injection made register_shrinker() fail and the caller of
register_shrinker() did not check for failure.
Since allowing register_shrinker() callers to call unregister_shrinker()
when register_shrinker() failed can simplify error recovery path, this
patch makes unregister_shrinker() no-op when register_shrinker() failed.
Also, reset shrinker->nr_deferred in case unregister_shrinker() was
by error called twice.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Aliaksei Karaliou <akaraliou.dev@gmail.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Glauber Costa <glauber@scylladb.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: slab-out-of-bounds in xfrm_hash_rebuild+0xdbe/0xf00 net/xfrm/xfrm_policy.c:618
read of size 2 at addr ffff8801c8e92fe4 by task kworker/1:1/23 [..]
Workqueue: events xfrm_hash_rebuild [..]
__asan_report_load2_noabort+0x14/0x20 mm/kasan/report.c:428
xfrm_hash_rebuild+0xdbe/0xf00 net/xfrm/xfrm_policy.c:618
process_one_work+0xbbf/0x1b10 kernel/workqueue.c:2112
worker_thread+0x223/0x1990 kernel/workqueue.c:2246 [..]
The reproducer triggers:
1016 if (error) {
1017 list_move_tail(&walk->walk.all, &x->all);
1018 goto out;
1019 }
in xfrm_policy_walk() via pfkey (it sets tiny rcv space, dump
callback returns -ENOBUFS).
In this case, *walk is located the pfkey socket struct, so this socket
becomes visible in the global policy list.
It looks like this is intentional -- phony walker has walk.dead set to 1
and all other places skip such "policies".
Ccing original authors of the two commits that seem to expose this
issue (first patch missed ->dead check, second patch adds pfkey
sockets to policies dumper list).
Fixes: 880a6fab8f6ba5b ("xfrm: configure policy hash table thresholds by netlink") Fixes: 12a169e7d8f4b1c ("ipsec: Put dumpers on the dump list") Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Timo Teras <timo.teras@iki.fi> Cc: Christophe Gouault <christophe.gouault@6wind.com> Reported-by: syzbot <bot+c028095236fcb6f4348811565b75084c754dc729@syzkaller.appspotmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported a warning from rfkill_alloc(), and after a while
I think that the reason is that it was doing fault injection and
the dev_set_name() failed, leaving the name NULL, and we didn't
check the return value and got to rfkill_alloc() with a NULL name.
Since we really don't want a NULL name, we ought to check the
return value.
TCP sockets for IPv4 and IPv6 that are not listeners or in closed
stated are allowed to be attached to a KCM mux.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot+8865eaff7f9acd593945@syzkaller.appspotmail.com Signed-off-by: Tom Herbert <tom@quantonium.net> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to prevent sk_user_data being overwritten.
The check is done under the callback lock. This should prevent
a socket from being attached twice to a KCM mux. It also prevents
a socket from being attached for other use cases of sk_user_data
as long as the other cases set sk_user_data under the lock.
Followup work is needed to unify all the use cases of sk_user_data
to use the same locking.
Reported-by: syzbot+114b15f2be420a8886c3@syzkaller.appspotmail.com Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Signed-off-by: Tom Herbert <tom@quantonium.net> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API") Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_KASAN, we get an overly long stack frame due to inlining
the register access functions:
drivers/media/tuners/r820t.c: In function 'generic_set_freq.isra.7':
drivers/media/tuners/r820t.c:1334:1: error: the frame size of 2880 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
This is caused by a gcc bug that has now been fixed in gcc-8.
To work around the problem, we can pass the register data
through a local variable that older gcc versions can optimize
out as well.
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:
arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
According to the comment added to exynos_dt_pmu_match[] in commit 8b283c025443 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b062 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normal pathname lookup doesn't allow empty pathnames, but using
AT_EMPTY_PATH (with name_to_handle_at() or fstatat(), for example) you
can trigger an empty pathname lookup.
And not only is the RCU lookup in that case entirely unnecessary
(because we'll obviously immediately finalize the end result), it is
actively wrong.
Why? An empth path is a special case that will return the original
'dirfd' dentry - and that dentry may not actually be RCU-free'd,
resulting in a potential use-after-free if we were to initialize the
path lazily under the RCU read lock and depend on complete_walk()
finalizing the dentry.
Arnd Bergmann [Thu, 15 Feb 2018 15:16:57 +0000 (16:16 +0100)]
x86: fix build warnign with 32-bit PAE
I ran into a 4.9 build warning in randconfig testing, starting with the
KAISER patches:
arch/x86/kernel/ldt.c: In function 'alloc_ldt_struct':
arch/x86/include/asm/pgtable_types.h:208:24: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define __PAGE_KERNEL (__PAGE_KERNEL_EXEC | _PAGE_NX)
^
arch/x86/kernel/ldt.c:81:6: note: in expansion of macro '__PAGE_KERNEL'
__PAGE_KERNEL);
^~~~~~~~~~~~~
I originally ran into this last year when the patches were part of linux-next,
and tried to work around it by using the proper 'pteval_t' types consistently,
but that caused additional problems.
This takes a much simpler approach, and makes the argument type of the dummy
helper always 64-bit, which is wide enough for any page table layout and
won't hurt since this call is just an empty stub anyway.
Currently, x86_cache_size is of type int, which makes no sense as we
will never have a valid cache size equal or less than 0. So instead of
initializing this variable to -1, it can perfectly be initialized to 0
and use it as an unsigned variable instead.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org>
Addresses-Coverity-ID: 1464429 Link: http://lkml.kernel.org/r/20180213192208.GA26414@embeddedor.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joe Konno reported a compile failure resulting from using an MSR
without inclusion of <asm/msr-index.h>, and while the current code builds
fine (by accident) this needs fixing for future patches.
For architectures providing their own implementation of
array_index_mask_nospec() in asm/barrier.h, attempting to use WARN_ONCE() to
complain about out-of-range parameters using WARN_ON() results in a mess
of mutually-dependent include files.
Rather than unpick the dependencies, simply have the core code in nospec.h
perform the checking for us.
Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1517840166-15399-1-git-send-email-will.deacon@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 64-bit builds, we should not rely on "int $0x80" working (it only does if
CONFIG_IA32_EMULATION=y is enabled). To keep the "Set TF and check int80"
test running on 64-bit installs with CONFIG_IA32_EMULATION=y enabled, build
this test only if we can also build 32-bit binaries (which should be a
good approximation for that).
protection_keys.c: In function ‘dumpit’:
protection_keys.c:419:3: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result [-Wunused-result]
write(1, buf, nr_read);
^~~~~~~~~~~~~~~~~~~~~~
Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Shuah Khan <shuahkh@osg.samsung.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two variables should check whether SPEC_CTRL and PRED_CMD are
supposed to be passed through to L2 guests or not. While
msr_write_intercepted_l01 would return 'true' if it is not passed through.
So just invert the result of msr_write_intercepted_l01 to implement the
correct semantics.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Jim Mattson <jmattson@google.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: kvm@vger.kernel.org Cc: sironi@amazon.de Fixes: 086e7d4118cc ("KVM: VMX: Allow direct access to MSR_IA32_SPEC_CTRL") Link: http://lkml.kernel.org/r/1518305967-31356-5-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With retpoline, tight loops of "call this function for every XXX" are
very much pessimised by taking a prediction miss *every* time. This one
is by far the biggest contributor to the guest launch time with retpoline.
By marking the iterator slot_handle_…() functions always_inline, we can
ensure that the indirect function call can be optimised away into a
direct call and it actually generates slightly smaller code because
some of the other conditionals can get optimised away too.
Performance is now pretty close to what we see with nospectre_v2 on
the command line.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Filippo Sironi <sironi@amazon.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Filippo Sironi <sironi@amazon.de> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: jmattson@google.com Cc: karahmed@amazon.de Cc: kvm@vger.kernel.org Cc: rkrcmar@redhat.com Link: http://lkml.kernel.org/r/1518305967-31356-4-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arjan points out that the Intel document only clears the 0xc2 microcode
on *some* parts with CPUID 506E3 (INTEL_FAM6_SKYLAKE_DESKTOP stepping 3).
For the Skylake H/S platform it's OK but for Skylake E3 which has the
same CPUID it isn't (yet) cleared.
So removing it from the blacklist was premature. Put it back for now.
Also, Arjan assures me that the 0x84 microcode for Kaby Lake which was
featured in one of the early revisions of the Intel document was never
released to the public, and won't be until/unless it is also validated
as safe. So those can change to 0x80 which is what all *other* versions
of the doc have identified.
Once the retrospective testing of existing public microcodes is done, we
should be back into a mode where new microcodes are only released in
batches and we shouldn't even need to update the blacklist for those
anyway, so this tweaking of the list isn't expected to be a thing which
keeps happening.
Requested-by: Arjan van de Ven <arjan.van.de.ven@intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: kvm@vger.kernel.org Cc: pbonzini@redhat.com Link: http://lkml.kernel.org/r/1518449255-2182-1-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel have retroactively blessed the 0xc2 microcode on Skylake mobile
and desktop parts, and the Gemini Lake 0x22 microcode is apparently fine
too. We blacklisted the latter purely because it was present with all
the other problematic ones in the 2018-01-08 release, but now it's
explicitly listed as OK.
We still list 0x84 for the various Kaby Lake / Coffee Lake parts, as
that appeared in one version of the blacklist and then reverted to
0x80 again. We can change it if 0x84 is actually announced to be safe.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: jmattson@google.com Cc: karahmed@amazon.de Cc: kvm@vger.kernel.org Cc: pbonzini@redhat.com Cc: rkrcmar@redhat.com Cc: sironi@amazon.de Link: http://lkml.kernel.org/r/1518305967-31356-2-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At entry userspace may have populated registers with values that could
otherwise be useful in a speculative execution attack. Clear them to
minimize the kernel's attack surface.
Originally-From: Andi Kleen <ak@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/151787989697.7847.4083702787288600552.stgit@dwillia2-desk3.amr.corp.intel.com
[ Made small improvements to the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f60 updated it incorrectly
while moving from platform code to DT. Fix it.
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.
SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.
Fixes: 1fb47e0a9ba4 ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes") Cc: stable@vger.kernel.org Reported-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the implementation of some 16-bit ID system calls
(namely, setuid16/setgid16 and setfsuid16/setfsgid16) used type cast
instead of low2highgid/low2highuid macros for converting [GU]IDs, which
led to incorrect handling of value of -1 (which ought to be considered
invalid).
If we can't get inode lock immediately in the function
ocfs2_inode_lock_with_page() when reading a page, we should not return
directly here, since this will lead to a softlockup problem when the
kernel is configured with CONFIG_PREEMPT is not set. The method is to
get a blocking lock and immediately unlock before returning, this can
avoid CPU resource waste due to lots of retries, and benefits fairness
in getting lock among multiple nodes, increase efficiency in case
modifying the same file frequently from multiple nodes.
The softlockup crash (when set /proc/sys/kernel/softlockup_panic to 1)
looks like:
About performance improvement, we can see the testing time is reduced,
and CPU utilization decreases, the detailed data is as follows. I ran
multi_mmap test case in ocfs2-test package in a three nodes cluster.
Before applying this patch:
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
2754 ocfs2te+ 20 0 170248 6980 4856 D 80.73 0.341 0:18.71 multi_mmap
1505 root rt 0 222236 123060 97224 S 2.658 6.015 0:01.44 corosync
5 root 20 0 0 0 0 S 1.329 0.000 0:00.19 kworker/u8:0
95 root 20 0 0 0 0 S 1.329 0.000 0:00.25 kworker/u8:1
2728 root 20 0 0 0 0 S 0.997 0.000 0:00.24 jbd2/sda1-33
2721 root 20 0 0 0 0 S 0.664 0.000 0:00.07 ocfs2dc-3C8CFD4
2750 ocfs2te+ 20 0 142976 4652 3532 S 0.664 0.227 0:00.28 mpirun
Link: http://lkml.kernel.org/r/1514447305-30814-1-git-send-email-ghe@suse.com Fixes: 1cce4df04f37 ("ocfs2: do not lock/unlock() inode DLM lock") Signed-off-by: Gang He <ghe@suse.com> Reviewed-by: Eric Ren <zren@suse.com> Acked-by: alex chen <alex.chen@huawei.com> Acked-by: piaojun <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate the error of devfreq_add_device() in devm_devfreq_add_device()
rather than statically returning ENOMEM. This makes it slightly faster
to pinpoint the cause of a returned error.
Fixes: 8cd84092d35e ("PM / devfreq: Add resource-managed function for devfreq device") Cc: stable@vger.kernel.org Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some OpenPOWER boxes can have same pstate values for nominal and
pmin pstates. In these boxes the current code will not initialize
'powernv_pstate_info.min' variable and result in erroneous CPU
frequency reporting. This patch fixes this problem.
Fixes: 09ca4c9b5958 (cpufreq: powernv: Replacing pstate_id with frequency table index) Reported-by: Alvin Wang <wangat@tw.ibm.com> Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 4.8+ <stable@vger.kernel.org> # 4.8+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following sequence:
* Change queue pair state into IB_QPS_ERR.
* Post a work request on the queue pair.
Triggers the following race condition in the rdma_rxe driver:
* rxe_qp_error() triggers an asynchronous call of rxe_completer(), the function
that examines the QP send queue.
* rxe_post_send() posts a work request on the QP send queue.
If rxe_completer() runs prior to rxe_post_send(), it will drain the send
queue and the driver will assume no further action is necessary.
However, once we post the send to the send queue, because the queue is
in error, no send completion will ever happen and the send will get
stuck. In order to process the send, we need to make sure that
rxe_completer() gets run after a send is posted to a queue pair in an
error state. This patch ensures that happens.
Running the compaction_test sometimes results in out-of-memory
failures. When I debugged this, it turned out that the code to
reset the number of hugepages to the initial value is simply
broken since we write into an open sysctl file descriptor
multiple times without seeking back to the start.
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Fixes: 4196670be786 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The request builder was using the incorrect inlines to
build the request header resulting in incorrect data
in the atomic header.
Fix by using the appropriate inlines to create the request.
Fixes: 261a4351844b ("IB/qib,IB/hfi: Use core common header file") Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com> Cc: stable@vger.kernel.org (v3.14+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit 2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA sequencer core initializes the event pool on demand by invoking
snd_seq_pool_init() when the first write happens and the pool is
empty. Meanwhile user can reset the pool size manually via ioctl
concurrently, and this may lead to UAF or out-of-bound accesses since
the function tries to vmalloc / vfree the buffer.
A simple fix is to just wrap the snd_seq_pool_init() call with the
recently introduced client->ioctl_mutex; as the calls for
snd_seq_pool_init() from other side are always protected with this
mutex, we can avoid the race.
Add quirk to ensure a sync endpoint is properly configured.
This patch is a fix for same symptoms on Behringer UFX1204 as patch
from Albertto Aquirre on Dec 8 2016 for Axe-Fx II.
These laptops have a combined jack to attach headsets, the U727 on
the left, the U757 on the right, but a headsets microphone doesn't
work. Using hdajacksensetest I found that pin 0x19 changed the
present state when plugging the headset, in addition to 0x21, but
didn't have the correct configuration (shown as "Not connected").
So this sets the configuration to the same values as the headphone
pin 0x21 except for the device type microphone, which makes it
work correctly. With the patch the configured pins for U727 are
Pin 0x12 (Internal Mic, Mobile-In): present = No
Pin 0x14 (Internal Speaker): present = No
Pin 0x19 (Black Mic, Left side): present = No
Pin 0x1d (Internal Aux): present = No
Pin 0x21 (Black Headphone, Left side): present = No
Thinkpad Dock device support for ALC298 platform.
It need to use SSID for the quirk table.
Because IdeaPad also has ALC298 platform.
Use verb for the quirk table will confuse.
The layout of the UAC2 Control request and response varies depending on
the request type. With the current implementation, only the Layout 2
Parameter Block (with the 2-byte sized RANGE attribute) is handled
properly. For the Control requests with the 1-byte sized RANGE attribute
(Bass Control, Mid Control, Tremble Control), the response is parsed
incorrectly.
This commit:
* fixes the wLength field value in the request
* fixes parsing the range values from the response
Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0") Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 3cf32d180227 ("mtd: nand: vf610: switch to
mtd_ooblayout_ops") the driver started to use the NAND cores
default large page ooblayout. However, shortly after commit 6a623e076944 ("mtd: nand: add ooblayout for old hamming layout")
changed the default layout to the old hamming layout, which is
not what vf610_nfc is using. Specify the default large page
layout explicitly.
Fixes: 6a623e076944 ("mtd: nand: add ooblayout for old hamming layout") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a 9p request is successfully flushed, the server is expected to just
mark it as used without sending a 9p reply (ie, without writing data into
the buffer). In this case, virtqueue_get_buf() will return len == 0 and
we must not report a REQ_STATUS_RCVD status to the client, otherwise the
client will erroneously assume the request has not been flushed.
Cc: stable@vger.kernel.org Signed-off-by: Greg Kurz <groug@kaod.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The highest objectid, which is assigned to new inode, is decided at
the time of initializing fs roots. However, in cases where log replay
gets processed, the btree which fs root owns might be changed, so we
have to search it again for the highest objectid, otherwise creating
new inode would end up with -EEXIST.
cc: <stable@vger.kernel.org> v4.4-rc6+ Fixes: f32e48e92596 ("Btrfs: Initialize btrfs_root->highest_objectid when loading tree root and subvolume roots") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible that btrfs_sync_log() bails out after one of the two
btrfs_write_marked_extents() which convert extent state's state bit into
EXTENT_NEED_WAIT from EXTENT_DIRTY/EXTENT_NEW, however only EXTENT_DIRTY
and EXTENT_NEW are searched by free_log_tree() so that those extent states
with EXTENT_NEED_WAIT lead to memory leak.
cc: <stable@vger.kernel.org> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases that the whole fs flips into readonly status due to failures in
critical sections, then log tree's blocks are still dirty, and this leads
to a crash during umount time, the crash is about use-after-free,
cc: <stable@vger.kernel.org> v3.12+ Fixes: 681ae50917df ("Btrfs: cleanup reserved space when freeing tree log on error") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
@cur_offset is not set back to what it should be (@cow_start) if
btrfs_next_leaf() returns something wrong, and the range [cow_start,
cur_offset) remains locked forever.
cc: <stable@vger.kernel.org> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If chap_server_compute_md5() fails early, e.g. via CHAP_N mismatch, then
crypto_free_shash() is called with a NULL pointer which gets
dereferenced in crypto_shash_tfm().
Fixes: 69110e3cedbb ("iscsi-target: Use shash and ahash") Suggested-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David Disseldorp <ddiss@suse.de> Cc: stable@vger.kernel.org # 4.6+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b75
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection lost problem") Cc: Stable <stable@vger.kernel.org> # 4.14+ Fix-suggested-by: Pkshih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3 Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When this method is set, the caller expects struct console_font fields
to be properly initialized when it returns. Leave it unset otherwise
nonsensical (leaked kernel stack) values are returned to user space.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent display node was also prematurely
freed.
Note that the display and timings node references are never put after a
successful dt-initialisation so the nodes would leak on later probe
deferrals and on driver unbind.
Fix child-node lookup during initialisation which was using the wrong
OF-helper and ended up searching the whole device tree depth-first
starting at the parent rather than just matching on its children.
To make things worse, the parent pci node could end up being prematurely
freed as of_find_node_by_name() drops a reference to its first argument.
Any matching child interrupt-controller node was also leaked.
MIPS_GENERIC selects some options conditional on BIG_ENDIAN which does
not exist.
Replace BIG_ENDIAN with CPU_BIG_ENDIAN which is the correct kconfig
name. Note that BMIPS_GENERIC does the same which confirms that this
patch is needed.
The functions devm_memremap_pages() and devm_memremap_pages_release() use
different ways to calculate the section-aligned amount of memory. The
latter function may use an incorrect size if the memory region is small
but straddles a section border.
Use the same code for both.
Cc: <stable@vger.kernel.org> Fixes: 5f29a77cd957 ("mm: fix mixed zone detection in devm_memremap_pages") Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function __ext4_grp_locked_error(), __save_error_info()
is called to save error info in super block block, but does not sync
that information to disk to info the subsequence fsck after reboot.
This patch writes the error information to disk. After this patch,
I think there is no obvious EXT4 error handle branches which leads to
"Remounting filesystem read-only" will leave the disk partition miss
the subsequence fsck.
This patch fixes a race between the shutdown path and bio completion
handling. In the ext4 direct io path with async io, after submitting a
bio to the block layer, if journal starting fails,
ext4_direct_IO_write() would bail out pretending that the IO
failed. The caller would have had no way of knowing whether or not the
IO was successfully submitted. So instead, we return -EIOCBQUEUED in
this case. Now, the caller knows that the IO was submitted. The bio
completion handler takes care of the error.
Tested: Ran the shutdown xfstest test 461 in loop for over 2 hours across
4 machines resulting in over 400 runs. Verified that the race didn't
occur. Usually the race was seen in about 20-30 iterations.
Sphinx emits various (26) warnings when building make target 'htmldocs'.
Currently struct definitions contain duplicate documentation, some as
kernel-docs and some as standard c89 comments. We can reduce
duplication while cleaning up the kernel docs.
Move all kernel-docs to right above each struct member. Use the set of
all existing comments (kernel-doc and c89). Add documentation for
missing struct members and function arguments.
According to the OPAL docs:
skiboot-5.2.5/doc/opal-api/opal-rtc-read-3.txt
skiboot-5.2.5/doc/opal-api/opal-rtc-write-4.txt
OPAL_HARDWARE may be returned from OPAL_RTC_READ or OPAL_RTC_WRITE and
this indicates either a transient or permanent error.
Prior to this patch, Linux was not dealing with OPAL_HARDWARE being a
permanent error particularly well, in that you could end up in a busy
loop.
This was not too hard to trigger on an AMI BMC based OpenPOWER machine
doing a continuous "ipmitool mc reset cold" to the BMC, the result of
that being that we'd get stuck in an infinite loop in
opal_get_rtc_time().
We now retry a few times before returning the error higher up the
stack.
Fixes: 16b1d26e77b1 ("rtc/tpo: Driver to support rtc and wakeup on PowerNV platform") Cc: stable@vger.kernel.org # v3.19+ Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the variable that was most recently initialized.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x, y, f, g, e, m;
statement S1,S2,S3,S4;
@@
x = f(...);
if (\(<+...x...+>\&e\)) S1 else S2
(
x = g(...);
|
m = g(...,&x,...);
|
y = g(...);
*if (e)
S3 else S4
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__unregister_ftrace_function_probe() will incorrectly parse the glob filter
because it resets the search variable that was setup by filter_parse_regex().
Al Viro reported this:
After that call of filter_parse_regex() we could have func_g.search not
equal to glob only if glob started with '!' or '*'. In the former case
we would've buggered off with -EINVAL (not = 1). In the latter we
would've set func_g.search equal to glob + 1, calculated the length of
that thing in func_g.len and proceeded to reset func_g.search back to
glob.
Suppose the glob is e.g. *foo*. We end up with
func_g.type = MATCH_MIDDLE_ONLY;
func_g.len = 3;
func_g.search = "*foo";
Feeding that to ftrace_match_record() will not do anything sane - we
will be looking for names containing "*foo" (->len is ignored for that
one).
Setting si_code to 0 is the same a setting si_code to SI_USER which is definitely
not correct. With si_code set to SI_USER si_pid and si_uid will be copied to
userspace instead of si_addr. Which is very wrong.
So fix this by using a sensible si_code (SEGV_MAPERR) for this failure.
Fixes: b920de1b77b7 ("mn10300: add the MN10300/AM33 architecture to the kernel") Cc: David Howells <dhowells@redhat.com> Cc: Masakazu Urade <urade.masakazu@jp.panasonic.com> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a writable mount, it is not expected for overlayfs to return
EINVAL/EROFS for fsync, even if dir/file is not changed.
This commit fixes the case of fsync of directory, which is easier to
address, because overlayfs already implements fsync file operation for
directories.
The problem reported by Raphael is that new PostgreSQL 10.0 with a
database in overlayfs where lower layer in squashfs fails to start.
The failure is due to fsync error, when PostgreSQL does fsync on all
existing db directories on startup and a specific directory exists
lower layer with no changes.
A NULL pointer reference kernel bug was observed when
acpi_nfit_add_dimm() called in acpi_nfit_register_dimms() failed. This
error path does not set nfit_mem->nvdimm, but the 2nd
list_for_each_entry() loop in the function assumes it's always set. Add
a check to nfit_mem->nvdimm.
Fixes: ba9c8dd3c222 ("acpi, nfit: add dimm device notification support") Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to be printing a raw kernel pointer to the kernel log at
every boot. So just remove it, and change the whole message to use the
correct dev_info() call at the same time.
Reported-by: Wang Qize <wang_qize@venustech.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
