The name of an IP is a function of its version. As such, given an IP
version, it should be clear to identify the name of that IP release.
With the current code, we keep that mapping clear for pre-GMDID IPs, but
ambiguous for GMDID-based ones. That causes two types of inconveniences:
1. The end user, who might not have all the necessary mapping at hand,
might be confused when seeing different possible IP names in the
dmesg log.
2. It makes a developer who is not familiar with the "IP version" to
"Release name" need to resort to looking at the specs to understand
see what version maps to what. While the specs should be the
authority on the mapping, we should make our lives easier by
reflecting that mapping in the source code.
Thus, since the IP name is tied to the version, let's remove the
ambiguity by using a "name" field in struct gmdid_map instead of
accumulating names in the descriptor instances.
This does result in the code having IP name being defined in
different structs (gmdid_map, xe_graphics_desc, xe_media_desc), but that
will be resolved in upcoming changes.
A side-effect of this change is that media_xe2 exactly matches
media_xelpmp now, so we just re-use the latter.
v2:
- Drop media_xe2 and re-use media_xelpmp. (Matt)
Both MSM8974 and MSM8226 have only CX as power domain with MX & PX being
handled as regulators. Handle this case by reodering pd_names to have CX
first, and handling that the driver core will already attach a single
power domain internally.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
[luca: minor changes] Signed-off-by: Luca Weiss <luca@lucaweiss.eu> Link: https://lore.kernel.org/r/20250206-wcnss-singlepd-v2-2-9a53ee953dee@lucaweiss.eu
[bjorn: Added missing braces to else after multi-statement if] Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 29390bb5661d ("blk-throttle: support prioritized processing of metadata")
takes bytes/ios carryover for prioritized processing of metadata. Turns out
we can support it by charging it directly without trimming slice, and the
result is same with carryover.
Cc: Tejun Heo <tj@kernel.org> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Acked-by: Tejun Heo <tj@kernel.org> Link: https://lore.kernel.org/r/20250305043123.3938491-3-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The phylink_expects_phy() function allows MAC drivers to check if they are
expecting a PHY to attach. The checking condition in phylink_expects_phy()
aims to achieve the same result as the checking condition in
phylink_attach_phy().
However, the checking condition in phylink_expects_phy() uses
pl->link_config.interface, while phylink_attach_phy() uses
pl->link_interface.
Initially, both pl->link_interface and pl->link_config.interface are set
to SGMII, and pl->cfg_link_an_mode is set to MLO_AN_INBAND.
When the interface switches from SGMII to 2500BASE-X,
pl->link_config.interface is updated by phylink_major_config().
At this point, pl->cfg_link_an_mode remains MLO_AN_INBAND, and
pl->link_config.interface is set to 2500BASE-X.
Subsequently, when the STMMAC interface is taken down
administratively and brought back up, it is blocked by
phylink_expects_phy().
Since phylink_expects_phy() and phylink_attach_phy() aim to achieve the
same result, phylink_expects_phy() should check pl->link_interface,
which never changes, instead of pl->link_config.interface, which is
updated by phylink_major_config().
Add drm_gem_is_imported() that tests if a GEM object's buffer has
been imported. Update the GEM code accordingly.
GEM code usually tests for imports if import_attach has been set
in struct drm_gem_object. But attaching a dma-buf on import requires
a DMA-capable importer device, which is not the case for many serial
busses like USB or I2C. The new helper tests if a GEM object's dma-buf
has been created from the GEM object.
MT8188 uses DPI1 to output to the HDMI controller: add the
Start of Frame and End of Frame configuration for the DPI1
IP to the tables to unblock generation and sending of these
signals to the GCE.
A cache device failing to resume due to mapping errors should not be
retried, as the failure leaves a partially initialized policy object.
Repeating the resume operation risks triggering BUG_ON when reloading
cache mappings into the incomplete policy object.
Reproduce steps:
1. create a cache metadata consisting of 512 or more cache blocks,
with some mappings stored in the first array block of the mapping
array. Here we use cache_restore v1.0 to build the metadata.
The current xHCI driver does not validate whether a page size of 4096
bytes is supported. Address the issue by setting the page size to the
value supported by the xHCI controller, as read from the Page Size
register. In the event of an unexpected value; default to a 4K page size.
Additionally, this commit removes unnecessary debug messages and instead
prints the supported and used page size once.
The xHCI controller supports page sizes of (2^{(n+12)}) bytes, where 'n'
is the Page Size Bit. Only one page size is supported, with a maximum
page size of 128 KB.
[Why]
There are several ns_to_ktime() calls that require using nanoseconds. It is
better to replace them with us_to_ktime() to make code clear, getting rid
of multiplication by 1000.
Also the timer function code may have an integer wrap-around issue. Since
both tx_custom_low_usecs and tx_custom_high_usecs can be set to up to 9999999 from the user space via cec_pin_error_inj_parse_line(), this may
cause usecs to be overflowed when adap->monitor_pin_cnt is zero and usecs
is multiplied by 1000.
[How]
Take advantage of using an appropriate helper func us_to_ktime() instead of
ns_to_ktime() to improve readability and to make the code clearer. And this
also mitigates possible integer wrap-arounds when usecs value is too large
and it is multiplied by 1000.
Found by Linux Verification Center (linuxtesting.org) with Svace.
An of_node_put(i2c_bus) call was immediately used after a pointer check
for an of_find_i2c_adapter_by_node() call in this function implementation.
Thus call such a function only once instead directly before the check.
This issue was transformed by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
This does not necessarily get included through asm/io.h:
drivers/soc/samsung/exynos3250-pmu.c:120:18: error: use of undeclared identifier 'ARRAY_SIZE'
120 | for (i = 0; i < ARRAY_SIZE(exynos3250_list_feed); i++) {
| ^
drivers/soc/samsung/exynos5250-pmu.c:162:18: error: use of undeclared identifier 'ARRAY_SIZE'
162 | for (i = 0; i < ARRAY_SIZE(exynos5_list_both_cnt_feed); i++) {
| ^
TTM doesn't support fair eviction via WW locking, this mitigated in by
using retry loops in exec and preempt rebind worker. Extend this retry
loop to BO allocation. Once TTM supports fair eviction this patch can be
reverted.
Clear root PT entry and invalidate entire VM's address space when
closing the VM. Will prevent the GPU from accessing any of the VM's
memory after closing.
v2:
- s/vma/vm in kernel doc (CI)
- Don't nuke migration VM as this occur at driver unload (CI)
v3:
- Rebase and pull into SVM series (Thomas)
- Wait for pending binds (Thomas)
v5:
- Remove xe_gt_tlb_invalidation_fence_fini in error case (Matt Auld)
- Drop local migration bool (Thomas)
v7:
- Add drm_dev_enter/exit protecting invalidation (CI, Matt Auld)
The rseq_cs field is documented as being set to 0 by user-space prior to
registration, however this is not currently enforced by the kernel. This
can result in a segfault on return to user-space if the value stored in
the rseq_cs field doesn't point to a valid struct rseq_cs.
The correct solution to this would be to fail the rseq registration when
the rseq_cs field is non-zero. However, some older versions of glibc
will reuse the rseq area of previous threads without clearing the
rseq_cs field and will also terminate the process if the rseq
registration fails in a secondary thread. This wasn't caught in testing
because in this case the leftover rseq_cs does point to a valid struct
rseq_cs.
What we can do is clear the rseq_cs field on registration when it's
non-zero which will prevent segfaults on registration and won't break
the glibc versions that reuse rseq areas on thread creation.
snd_seq_poll() calls snd_seq_write_pool_allocated() that reads out a
field in client->pool object, while it can be updated concurrently via
ioctls, as reported by syzbot. The data race itself is harmless, as
it's merely a poll() call, and the state is volatile. OTOH, the read
out of poll object info from the caller side is fragile, and we can
leave it better in snd_seq_pool_poll_wait() alone.
A similar pattern is seen in snd_seq_kernel_client_write_poll(), too,
which is called from the OSS sequencer.
This patch drops the pool checks from the caller side and add the
pool->lock in snd_seq_pool_poll_wait() for better data consistency.
Some discrete graphics cards such as the NVIDIA RTX A6000 support
resizable BARs. When connecting an A6000 card to the NVIDIA IGX Orin
platform, resizing the BAR1 aperture to 8GB fails because the current
device-tree configuration for the PCIe C5 slot cannot support this.
Fix this by updating the device-tree 'reg' and 'ranges' properties for
the PCIe C5 slot to support this.
According to the board schematics the enable pin of this regulator is
connected to gpio line #9 of the first instance of the TCA9539
GPIO expander, so adjust it.
While the entry get in svm_range_unmap_from_cpu is the last entry, and
the entry is page fault, it also need to be dropped. So for equal case,
it also need to be dropped.
v2:
Only modify the svm_range_restore_pages.
Signed-off-by: Emily Deng <Emily.Deng@amd.com> Reviewed-by: Xiaogang Chen<xiaogang.chen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For default policy, driver will issue an RMA event when the number of
bad pages is greater than 8 physical rows, rather than reaches 8
physical rows, don't rely on threshold configurable parameters in
default mode.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Alex Sierra <alex.sierra@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Amber Lin <Amber.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set per-process static sh_mem config only once during process
initialization. Move all static changes from update_qpd() which is
called each time a queue is created to set_cache_memory_policy() which
is called once during process initialization.
set_cache_memory_policy() is currently defined only for cik and vi
family. So this commit only focuses on these two. A separate commit will
address other asics.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Reviewed-by: Amber Lin <Amber.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Define set_cache_memory_policy() for these asics and move all static
changes from update_qpd() which is called each time a queue is created
to set_cache_memory_policy() which is called once during process
initialization
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Reviewed-by: Amber Lin <Amber.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While MXS_DCP_CONTROL0_OTP_KEY is set, the CRYPTO_KEY (DCP_PAES_KEY_OTP)
is used even if the UNIQUE_KEY (DCP_PAES_KEY_UNIQUE) is selected. This
is not clearly documented, but this implementation is consistent with
NXP's downstream kernel fork and optee_os.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike the decompression code, the compression code in LZO never
checked for output overruns. It instead assumes that the caller
always provides enough buffer space, disregarding the buffer length
provided by the caller.
Add a safe compression interface that checks for the end of buffer
before each write. Use the safe interface in crypto/lzo.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently BARs that have been disabled by the endpoint controller driver
will result in a test FAIL.
Returning FAIL for a BAR that is disabled seems overly pessimistic.
There are EPC that disables one or more BARs intentionally.
One reason for this is that there are certain EPCs that are hardwired to
expose internal PCIe controller registers over a certain BAR, so the EPC
driver disables such a BAR, such that the host will not overwrite random
registers during testing.
Such a BAR will be disabled by the EPC driver's init function, and the
BAR will be marked as BAR_RESERVED, such that it will be unavailable to
endpoint function drivers.
Let's return FAIL only for BARs that are actually enabled and failed the
test, and let's return skip for BARs that are not even enabled.
The current code returns -ENOMEM if test->bar[barno] is NULL.
There can be two reasons why test->bar[barno] is NULL:
1) The pci_ioremap_bar() call in pci_endpoint_test_probe() failed.
2) The BAR was skipped, because it is disabled by the endpoint.
Many PCI endpoint controller drivers will disable all BARs in their
init function. A disabled BAR will have a size of 0.
A PCI endpoint function driver will be able to enable any BAR that
is not marked as BAR_RESERVED (which means that the BAR should not
be touched by the EPF driver).
Thus, perform check if the size is 0, before checking if
test->bar[barno] is NULL, such that we can return different errors.
This will allow the selftests to return SKIP instead of FAIL for
disabled BARs.
Fix a kernel oops found while testing the stm32_pcie Endpoint driver
with handling of PERST# deassertion:
During EP initialization, pci_epf_test_alloc_space() allocates all BARs,
which are further freed if epc_set_bar() fails (for instance, due to no
free inbound window).
However, when pci_epc_set_bar() fails, the error path:
pci_epc_set_bar() ->
pci_epf_free_space()
does not clear the previous assignment to epf_test->reg[bar].
Then, if the host reboots, the PERST# deassertion restarts the BAR
allocation sequence with the same allocation failure (no free inbound
window), creating a double free situation since epf_test->reg[bar] was
deallocated and is still non-NULL.
Thus, make sure that pci_epf_alloc_space() and pci_epf_free_space()
invocations are symmetric, and as such, set epf_test->reg[bar] to NULL
when memory is freed.
The boot status in the watchdog device struct is updated during
controller probe stage. Application layer can get the boot status
through the command, cat /sys/class/watchdog/watchdogX/bootstatus.
The bootstatus can be,
WDIOF_CARDRESET => System is reset due to WDT timeout occurs.
Others => Other reset events, e.g., power on reset.
On ASPEED platforms, boot status is recorded in the SCU registers.
- AST2400: Only a bit is used to represent system reset triggered by
any WDT controller.
- AST2500/AST2600: System reset triggered by different WDT controllers
can be distinguished by different SCU bits.
Besides, on AST2400 and AST2500, since alternating boot event is
also triggered by using WDT timeout mechanism, it is classified
as WDIOF_CARDRESET.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20250113093737.845097-2-chin-ting_kuo@aspeedtech.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the PMU register bits for the ExynosAutoV920 SoC.
This SoC has different bit information compared to its previous
version, ExynosAutoV9, and we have made the necessary adjustments.
Limit the number of slots in pipe_resize_ring() to the maximum value
representable by pipe->{head,tail}. Values beyond the max limit can
lead to incorrect pipe occupancy related calculations where the pipe
will never appear full.
In coresight-etb10 drivers, etb_drvdata->spinlock can be held
during __schedule() by perf_event_task_sched_out()/in().
Since etb_drvdata->spinlock type is spinlock_t and
perf_event_task_sched_out()/in() is called after acquiring rq_lock,
which is raw_spinlock_t (an unsleepable lock),
this poses an issue in PREEMPT_RT kernel where spinlock_t is sleepable.
To address this, change type etb_drvdata->spinlock in coresight-etb10 drivers,
which can be called by perf_event_task_sched_out()/in(),
from spinlock_t to raw_spinlock_t.
Reviewed-by: James Clark <james.clark@linaro.org> Reviewed-by: Mike Leach <mike.leach@linaro.org> Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20250306121110.1647948-6-yeoreum.yun@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There're few sysfs attributes(RW) whose store method is protected
with q->limits_lock, however the corresponding show method of these
attributes run holding q->sysfs_lock and that doesn't make sense
as ideally the show method of these attributes should also run
holding q->limits_lock instead of q->sysfs_lock. Hence update the
show method of these sysfs attributes so that reading of these
attributes acquire q->limits_lock instead of q->sysfs_lock.
Similarly, there're few sysfs attributes(RO) whose show method is
currently protected with q->sysfs_lock however updates to these
attributes could occur using atomic limit update APIs such as queue_
limits_start_update() and queue_limits_commit_update() which run
holding q->limits_lock. So that means that reading these attributes
holding q->sysfs_lock doesn't make sense. Hence update the show method
of these sysfs attributes(RO) such that they run with holding q->
limits_lock instead of q->sysfs_lock.
We have defined a new macro QUEUE_LIM_RO_ENTRY() which uses new ->show_
limit() method and it runs holding q->limits_lock. All existing sysfs
attributes(RO) which needs protection using q->limits_lock while
reading have been now updated to use this new macro for initialization.
Also, the existing QUEUE_LIM_RW_ENTRY() is updated to use new ->show_
limit() method for reading attributes instead of existing ->show()
method. As ->show_limit() runs holding q->limits_lock, the existing
sysfs attributes(RW) requiring protection are now inherently protected
using q->limits_lock instead of q->sysfs_lock.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Nilay Shroff <nilay@linux.ibm.com> Link: https://lore.kernel.org/r/20250304102551.2533767-2-nilay@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2545c1c948a6 ("auxdisplay: Move hwidth and bwidth to struct
hd44780_common") makes charlcd_alloc() argument-less effectively dropping
the single allocation for the struct charlcd_priv object along with
the driver specific one. Restore that behaviour here.
[Why]
When switching between PSR/Replay,
the DPCD config of previous mode is not cleared,
resulting in unexpected behavior in TCON.
[How]
Initialize the DPCD in setup function
Reviewed-by: Robin Chen <robin.chen@amd.com> Signed-off-by: Leon Huang <Leon.Huang1@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
In some cases the remain de-tile buffer segments will be greater
than zero if we don't add the non-top pipe to calculate, at
this time the override de-tile buffer size will be valid and used.
But it makes the de-tile buffer segments used finally for all of pipes
exceed the maximum.
[HOW]
Add the non-top pipe to calculate the remain de-tile buffer segments.
Don't set override size to use the average according to pipe count
if the value exceed the maximum.
Reviewed-by: Charlene Liu <charlene.liu@amd.com> Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When spanning datagram construction over multiple send calls using
MSG_MORE, per datagram settings are configured on the first send.
That is when ip(6)_setup_cork stores these settings for subsequent use
in __ip(6)_append_data and others.
The only flag that escaped this was dontfrag. As a result, a datagram
could be constructed with df=0 on the first sendmsg, but df=1 on a
next. Which is what cmsg_ip.sh does in an upcoming MSG_MORE test in
the "diff" scenario.
Changing datagram conditions in the middle of constructing an skb
makes this already complex code path even more convoluted. It is here
unintentional. Bring this flag in line with expected sockopt/cmsg
behavior.
And stop passing ipc6 to __ip6_append_data, to avoid such issues
in the future. This is already the case for __ip_append_data.
inet6_cork had a 6 byte hole, so the 1B flag has no impact.
Some regulatory bodies doesn't allow IR (initiate radioation) on a
specific subband, but allows it for channels with a bandwidth of 20 MHz.
Add a channel flag that indicates that, and consider it in
cfg80211_reg_check_beaconing.
While on it, fix the kernel doc of enum nl80211_reg_rule_flags and
change it to use BIT().
If U-APSD isn't enabled by us, then IEEE80211_STA_UAPSD_ENABLED
won't be set, but the AP can still support it in that case. Only
require U-APSD from the AP if we enabled it, don't require it to
be disabled on the AP if we didn't.
Do address translations only between shared links. It is
possible that while an non-AP MLD station and an AP MLD
station have shared links, the frame is intended to be sent
on a link which is not shared (for example when sending a
probe response).
If multi-link reconfiguration fails, we can disconnect with a local link
already allocated but the BSS entry not assigned yet, which leads to a
warning in cfg80211. Add a check to avoid the warning.
In the multi-link reconfiguration frame, the per-STA profile for
added links shouldn't include the multi-link element. Set the
association ID to an invalid value, so it doesn't erroneously
match the link ID if that happens to be zero.
The order of actions taken for debug was implemented incorrectly.
Now we implemented the dump split and do the FW reset only in the
middle of the dump (rather than the FW killing itself on error.)
As a result, some of the actions taken when applying the config
will now crash the device, so we need to fix the order.
The FW is now responsible of determining the SMPS mode.
If the user disabled power save in a certain vif, we send the vif-level
power command to clear out the POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK bit
for that vif.
But erroneously, the FW checks DEVICE_POWER_FLAGS_POWER_SAVE_ENA_MSK in
the device-level command to determine the SMPS mode.
To W/A this, send also the device-level command when the power save of a
vif changes, and disable power save if there is any vif that has power
save disabled.
iwl_trans_reclaim is warning if it is called when the FW is not alive.
But if it is called when there is a pending restart, i.e. after a FW
error, there is no need to warn, instead - return silently.
The commit 9e70a5e109a4 ("printk: Add per-console suspended state")
introduced the CON_SUSPENDED flag for consoles. The suspended consoles
will stop receiving messages, so don't unblank suspended consoles
because it won't be showing anything either way.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Reviewed-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20250226-printk-renaming-v1-5-0b878577f2e6@suse.com Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At the moment, if of_iommu_configure() allocates dev->iommu itself via
iommu_fwspec_init(), then suffers a DT parsing failure, it cleans up the
fwspec but leaves the empty dev_iommu hanging around. So far this is
benign (if a tiny bit wasteful), but we'd like to be able to reason
about dev->iommu having a consistent and unambiguous lifecycle. Thus
make sure that the of_iommu cleanup undoes precisely whatever it did.
When the device stalls an endpoint, current TD is assigned -EPIPE
status and Reset Endpoint is queued. If a Stop Endpoint is pending
at the time, it will run before Reset Endpoint and fail due to the
stall. Its handler will change TD's status to -EPROTO before Reset
Endpoint handler runs and initiates giveback.
Check if the stall has already been handled and don't try to do it
again. Since xhci_handle_halted_endpoint() performs this check too,
not overwriting td->status is the only difference.
I haven't seen this case yet, but I have seen a related one where
the xHC has already executed Reset Endpoint, EP Context state is
now Stopped and EP_HALTED is set. If the xHC took a bit longer to
execute Reset Endpoint, said case would become this one.
Per the SD Host Controller Simplified Specification v4.20 §3.2.3, change
the SD card clock parameters only after first disabling the external card
clock. Doing this fixes a spurious clock pulse on Baytrail and Apollo Lake
SD controllers which otherwise breaks voltage switching with a specific
Swissbit SD card.
Add support for Exynos7870 DW MMC controllers, for both SMU and non-SMU
variants. These controllers require a quirk to access 64-bit FIFO in 32-bit
accesses (DW_MMC_QUIRK_FIFO64_32).
pud_bad() is currently defined in terms of pud_table(). Although for some
configs, pud_table() is hard-coded to true i.e. when using 64K base pages
or when page table levels are less than 3.
pud_bad() is intended to check that the pud is configured correctly. Hence
let's open-code the same check that the full version of pud_table() uses
into pud_bad(). Then it always performs the check regardless of the config.
Cc: Will Deacon <will@kernel.org> Cc: Ard Biesheuvel <ardb@kernel.org> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20250221044227.1145393-7-anshuman.khandual@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check for pmd_table() in pmd_trans_huge() rather then just checking for the
PMD_TABLE_BIT. But ensure all present-invalid entries are handled correctly
by always setting PTE_VALID before checking with pmd_table().
Cc: Will Deacon <will@kernel.org> Cc: Ard Biesheuvel <ardb@kernel.org> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20250221044227.1145393-8-anshuman.khandual@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.
So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.
GCC 15's -Wunterminated-string-initialization saw that "id" was not
including the required trailing NUL character. Instead of marking "id"
with __nonstring[1], expand the length of the string as it is used in
(debugging) format strings that expect a properly formed C string.
nf_conntrack_max and nf_conntrack_expect_max sysctls were authorized to
be written any negative value, which would then be stored in the
unsigned int variables nf_conntrack_max and nf_ct_expect_max variables.
While the do_proc_dointvec_conv function is supposed to limit writing
handled by proc_dointvec proc_handler to INT_MAX. Such a negative value
being written in an unsigned int leads to a very high value, exceeding
this limit.
Moreover, the nf_conntrack_expect_max sysctl documentation specifies the
minimum value is 1.
The proc_handlers have thus been updated to proc_dointvec_minmax in
order to specify the following write bounds :
* Bound nf_conntrack_max sysctl writings between SYSCTL_ZERO
and SYSCTL_INT_MAX.
* Bound nf_conntrack_expect_max sysctl writings between SYSCTL_ONE
and SYSCTL_INT_MAX as defined in the sysctl documentation.
With this patch applied, sysctl writes outside the defined in the bound
will thus lead to a write error :
Some of 11ax AP set the UL HE-SIG-A2 reserved subfield to all 0s, which
will cause the 11be chip to recognize trigger frame as EHT. We propose
a method to bypass the "UL HE-SIG-A2 reserved subfield" and always uses
HE TB in response to the AP's trigger frame.
This report will feedback some basic information from firmware(PTA counter,
report counter, mailbox counter etc). And the report version need to match
driver & firmware both side. The original logic break the switch case logic
before driver update the report version. It made the report can not be
parsed correctly. Delete the break at the version 7 and 8.
Add logic to count C2H event report.
This reverts commit f590308536db ("timer debug: Hide kernel addresses via
%pK in /proc/timer_list")
The timer list helper SEQ_printf() uses either the real seq_printf() for
procfs output or vprintk() to print to the kernel log, when invoked from
SysRq-q. It uses %pK for printing pointers.
In the past %pK was prefered over %p as it would not leak raw pointer
values into the kernel log. Since commit ad67b74d2469 ("printk: hash
addresses printed with %p") the regular %p has been improved to avoid this
issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer, easier to reason
about and sufficient here.
Add PRP specific function for handling duplicate
packets. This is needed because of potential
L2 802.1p prioritization done by network switches.
The L2 prioritization can re-order the PRP packets
from a node causing the existing implementation to
discard the frame(s) that have been received 'late'
because the sequence number is before the previous
received packet. This can happen if the node is
sending multiple frames back-to-back with different
priority.
All Rockchip GMAC variants typically write to GRF regs to control e.g.
interface mode, speed and MAC rx/tx delay. Newer SoCs such as RK3576 and
RK3588 use a mix of GRF and peripheral GRF regs. These syscon regmaps is
located with help of a rockchip,grf and rockchip,php-grf phandle.
However, validating the rockchip,grf and rockchip,php-grf syscon regmap
is deferred until e.g. interface mode or speed is configured, inside the
individual SoC specific operations.
Change to validate the rockchip,grf and rockchip,php-grf syscon regmap
at probe time to simplify all SoC specific operations.
This should not introduce any backward compatibility issues as all
GMAC nodes have been added together with a rockchip,grf phandle (and
rockchip,php-grf where required) in their initial commit.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250308213720.2517944-3-jonas@kwiboo.se Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Frederic pointed out that the memory operations to initialize the timer are
not guaranteed to be visible, when __lock_timer() observes timer::it_signal
valid under timer::it_lock:
T0 T1
--------- -----------
do_timer_create()
// A
new_timer->.... = ....
spin_lock(current->sighand)
// B
WRITE_ONCE(new_timer->it_signal, current->signal)
spin_unlock(current->sighand)
sys_timer_*()
t = __lock_timer()
spin_lock(&timr->it_lock)
// observes B
if (timr->it_signal == current->signal)
return timr;
if (!t)
return;
// Is not guaranteed to observe A
Protect the write of timer::it_signal, which makes the timer valid, with
timer::it_lock as well. This guarantees that T1 must observe the
initialization A completely, when it observes the valid signal pointer
under timer::it_lock. sighand::siglock must still be taken to protect the
signal::posix_timers list.
Currently, the IB uverbs API calls uobj_get_uobj_read(), which in turn
uses the rdma_lookup_get_uobject() helper to retrieve user objects.
In case of failure, uobj_get_uobj_read() returns NULL, overriding the
error code from rdma_lookup_get_uobject(). The IB uverbs API then
translates this NULL to -EINVAL, masking the actual error and
complicating debugging. For example, applications calling ibv_modify_qp
that fails with EBUSY when retrieving the QP uobject will see the
overridden error code EINVAL instead, masking the actual error.
Furthermore, based on rdma-core commit:
"2a22f1ced5f3 ("Merge pull request #1568 from jakemoroni/master")"
Kernel's IB uverbs return values are either ignored and passed on as is
to application or overridden with other errnos in a few cases.
Thus, to improve error reporting and debuggability, propagate the
original error from rdma_lookup_get_uobject() instead of replacing it
with EINVAL.
When dioread_nolock is turned on (the default), it will convert unwritten
extents to written at ext4_end_io_end(), even if the data writeback fails.
It leads to the possibility that stale data may be exposed when the
physical block corresponding to the file data is read-only (i.e., writes
return -EIO, but reads are normal).
Therefore a new ext4_io_end->flags EXT4_IO_END_FAILED is added, which
indicates that some bio write-back failed in the current ext4_io_end.
When this flag is set, the unwritten to written conversion is no longer
performed. Users can read the data normally until the caches are dropped,
after that, the failed extents can only be read to all 0.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Zhang Yi <yi.zhang@huawei.com> Link: https://patch.msgid.link/20250122110533.4116662-3-libaokun@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
data_err=abort aborts the journal on I/O errors. However, this option is
meaningless if journal is disabled, so it is rejected in nojournal mode
to reduce unnecessary checks. Also, this option is ignored upon remount.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://patch.msgid.link/20250122110533.4116662-4-libaokun@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Arguably, there are more chances of errors occurring during the
initialization of the hardware, so this should complete successfully
before the devicetree node's children are initialized.
st1202_dt_init() fills the led_classdev struct.
st1202_setup() initializes the hardware. Specifically, resets the chip,
enables its phase-shift delay feature, enables the device and disables all
the LEDs channels. All that writing to registers, with no input from
st1202_dt_init().
Real-world testing corroborates that calling st1202_setup() before
st1202_dt_init() doesn't cause any issue during initialization.
Switch the order of st1202_dt_init() and st1202_setup() to ensure the
hardware is correctly initialized before the led_classdev struct is
filled.
leds-st1202 requires the LED Pattern Trigger (LEDS_TRIGGER_PATTERN), which
is not selected when LED Trigger support is (LEDS_TRIGGERS).
To reproduce this:
- make menuconfig KCONFIG_CONFIG=
- select LEDS_ST1202 dependencies OF, I2C and LEDS_CLASS.
- select LEDS_ST1202
- LEDS_TRIGGERS is selected but LEDS_TRIGGER_PATTERN isn't.
The absence of LEDS_TRIGGER_PATTERN explicitly required can lead to builds
in which LEDS_ST1202 is selected while LEDS_TRIGGER_PATTERN isn't. The direct
result of that would be that /sys/class/leds/<led>/hw_pattern wouldn't be
available and there would be no way of interacting with the driver and
hardware from user space.
Add select LEDS_TRIGGER_PATTERN to Kconfig to meet the requirement and
indirectly document it as well.
On the QCM6490 boards, the LPASS firmware controls the complete clock
controller functionalities and associated power domains. However, only
the LPASS resets required to be controlled by the high level OS. Thus,
add support for the resets in the clock driver to enable the Audio SW
driver to assert/deassert the audio resets as needed.
The previous H616 support patch added a single LINEOUT DAPM pin switch
to the card controls. As the codec in this SoC only has a single route,
this seemed reasonable at the time, however is redundant given the
existing DAPM codec widget definitions controlling the digital and
analog sides of the codec.
It is also insufficient to describe the scenario where separate
components (muxes, jack detection etc) are used to modify the audio
route external to the SoC. For example the Anbernic RG(##)XX series of
devices uses a headphone jack detection switch, GPIO-controlled speaker
amplifier and a passive external mux chip to route audio.
Remove the redundant LINEOUT card control, and add a Speaker pin switch
control and Headphone DAPM widget to allow control of the above
hardware.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Ryan Walklin <ryan@testtoast.com> Tested-by: Philippe Simons <simons.philippe@gmail.com> Link: https://patch.msgid.link/20250214220247.10810-3-ryan@testtoast.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for GPIO headphone detection with the hp-det-gpios
property. In order for this to properly disable the path upon
removal of headphones, the output must be labelled Headphone which
is a common sink in the driver.
Describe a headphone jack and detection GPIO in the driver, check for
a corresponding device tree node, and enable jack detection in a new
machine init function if described.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Ryan Walklin <ryan@testtoast.com>
--
Changelog v1..v2:
- Separate DAPM changes into separate patch and add rationale.
Just use the default values. There's not need to
get the value from hardware and it could cause problems
if we do that at runtime and gfxoff is active.
Just use the default values. There's not need to
get the value from hardware and it could cause problems
if we do that at runtime and gfxoff is active.
The chipid macro/variable and regmap_read function call is not needed
because the TPS65219_REG_TI_DEV_ID register value is not a consistent value
across TPS65219 PMIC config versions. Reading from the DEV_ID register
without a consistent value to compare it to isn't useful. There isn't a
way to verify the match data ID is the same ID read from the DEV_ID device
register. 0xF0 isn't a DEV_ID value consistent across TPS65219 NVM
configurations.
For TPS65215, there is a consistent value in bits 5-0 of the DEV_ID
register. However, there are other error checks in place within probe()
that apply to both PMICs rather than keeping this isolated check for one
PMIC.
Each pin can be configured as a Special Function IO (SFIO) or GPIO,
where the SFIO enables the pin to operate in alternative modes such as
I2C, SPI, etc.
The current implementation sets all the pins back to SFIO mode
even if they were initially in GPIO mode. This can cause glitches
on the pins when pinctrl_gpio_free() is called.
Avoid these undesired glitches by storing the pin's SFIO/GPIO
state on GPIO request and restoring it on GPIO free.
On XenServer on Windows machine a platform device with ID 2 instead of
1 is used.
This device is mainly identical to device 1 but due to some Windows
update behaviour it was decided to use a device with a different ID.
This causes compatibility issues with Linux which expects, if Xen
is detected, to find a Xen platform device (5853:0001) otherwise code
will crash due to some missing initialization (specifically grant
tables). Specifically from dmesg
When using smc_pnet in SMC, it will only search the pnetid in the
base_ndev of the netdev hierarchy(both HW PNETID and User-defined
sw pnetid). This may not work for some scenarios when using SMC in
container on cloud environment.
In container, there have choices of different container network,
such as directly using host network, virtual network IPVLAN, veth,
etc. Different choices of container network have different netdev
hierarchy. Examples of netdev hierarchy show below. (eth0 and eth1
in host below is the netdev directly related to the physical device).
_______________________________
| _________________ |
| |POD | |
| | | |
| | eth0_________ | |
| |____| |__| |
| | | |
| | | |
| eth1|base_ndev| eth0_______ |
| | | | RDMA ||
| host |_________| |_______||
---------------------------------
netdev hierarchy if directly using host network
________________________________
| _________________ |
| |POD __________ | |
| | |upper_ndev| | |
| |eth0|__________| | |
| |_______|_________| |
| |lower netdev |
| __|______ |
| eth1| | eth0_______ |
| |base_ndev| | RDMA ||
| host |_________| |_______||
---------------------------------
netdev hierarchy if using IPVLAN
_______________________________
| _____________________ |
| |POD _________ | |
| | |base_ndev|| |
| |eth0(veth)|_________|| |
| |____________|________| |
| |pairs |
| _______|_ |
| | | eth0_______ |
| veth|base_ndev| | RDMA ||
| |_________| |_______||
| _________ |
| eth1|base_ndev| |
| host |_________| |
---------------------------------
netdev hierarchy if using veth
Due to some reasons, the eth1 in host is not RDMA attached netdevice,
pnetid is needed to map the eth1(in host) with RDMA device so that POD
can do SMC-R. Because the eth1(in host) is managed by CNI plugin(such
as Terway, network management plugin in container environment), and in
cloud environment the eth(in host) can dynamically be inserted by CNI
when POD create and dynamically be removed by CNI when POD destroy and
no POD related to the eth(in host) anymore. It is hard to config the
pnetid to the eth1(in host). But it is easy to config the pnetid to the
netdevice which can be seen in POD. When do SMC-R, both the container
directly using host network and the container using veth network can
successfully match the RDMA device, because the configured pnetid netdev
is a base_ndev. But the container using IPVLAN can not successfully
match the RDMA device and 0x03030000 fallback happens, because the
configured pnetid netdev is not a base_ndev. Additionally, if config
pnetid to the eth1(in host) also can not work for matching RDMA device
when using veth network and doing SMC-R in POD.
To resolve the problems list above, this patch extends to search user
-defined sw pnetid in the clc handshake ndev when no pnetid can be found
in the base_ndev, and the base_ndev take precedence over ndev for backward
compatibility. This patch also can unify the pnetid setup of different
network choices list above in container(Config user-defined sw pnetid in
the netdevice can be seen in POD).
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Reviewed-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch addresses an issue where authentication failures were being
erroneously reported due to negative test failures in the "ccm(aes)"
selftest.
pr_debug suppress unnecessary screaming of these tests.
projects / thirdparty / kernel / stable.git / log
