After the IPMI disconnect problem, the memory kept rising and we tried
to unload the driver to free the memory. However, only part of the
free memory is recovered after the driver is uninstalled. Using
ebpf to hook free functions, we find that neither ipmi_user nor
ipmi_smi_msg is free, only ipmi_recv_msg is free.
We find that the deliver_smi_err_response call in clean_smi_msgs does
the destroy processing on each message from the xmit_msg queue without
checking the return value and free ipmi_smi_msg.
deliver_smi_err_response is called only at this location. Adding the
free handling has no effect.
To verify, try using ebpf to trace the free function.
If ar5523_cmd() timed out, then ar5523_host_available() failed and
ar5523_probe() freed the device structure. So, ar5523_cmd_tx_cb()
might touch the freed structure.
This patch fixes this issue by canceling in-flight tx cmd if submitted
urb timed out.
The bug arises when a USB device claims to be an ATH9K but doesn't
have the expected endpoints. (In this case there was an interrupt
endpoint where the driver expected a bulk endpoint.) The kernel
needs to be able to handle such devices without getting an internal error.
If the input inode of hfs_write_inode() is incorrect:
struct inode
struct hfs_inode_info
struct hfs_cat_key
struct hfs_name
u8 len # len is greater than HFS_NAMELEN(31) which is the
maximum length of an HFS filename
OOB read occurred:
hfs_write_inode()
hfs_brec_find()
__hfs_brec_find()
hfs_cat_keycmp()
hfs_strcmp() # OOB read occurred due to len is too large
Fix this by adding a Check on len in hfs_write_inode() before calling
hfs_brec_find().
Link: https://lkml.kernel.org/r/20221130065959.2168236-1-zhangpeng362@huawei.com Signed-off-by: ZhangPeng <zhangpeng362@huawei.com> Reported-by: <syzbot+e836ff7133ac02be825f@syzkaller.appspotmail.com> Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jeff Layton <jlayton@kernel.org> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nanyong Sun <sunnanyong@huawei.com> Cc: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The integer overflow is descripted with following codes:
> 317 static comp_t encode_comp_t(u64 value)
> 318 {
> 319 int exp, rnd;
......
> 341 exp <<= MANTSIZE;
> 342 exp += value;
> 343 return exp;
> 344 }
Currently comp_t is defined as type of '__u16', but the variable 'exp' is
type of 'int', so overflow would happen when variable 'exp' in line 343 is
greater than 65535.
Patch series "nilfs2: fix UBSAN shift-out-of-bounds warnings on mount
time".
The first patch fixes a bug reported by syzbot, and the second one fixes
the remaining bug of the same kind. Although they are triggered by the
same super block data anomaly, I divided it into the above two because the
details of the issues and how to fix it are different.
Both are required to eliminate the shift-out-of-bounds issues at mount
time.
This patch (of 2):
If the block size exponent information written in an on-disk superblock is
corrupted, nilfs_sb2_bad_offset helper function can trigger
shift-out-of-bounds warning followed by a kernel panic (if panic_on_warn
is set):
shift exponent 38983 is too large for 64-bit type 'unsigned long long'
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x33d/0x3b0 lib/ubsan.c:322
nilfs_sb2_bad_offset fs/nilfs2/the_nilfs.c:449 [inline]
nilfs_load_super_block+0xdf5/0xe00 fs/nilfs2/the_nilfs.c:523
init_nilfs+0xb7/0x7d0 fs/nilfs2/the_nilfs.c:577
nilfs_fill_super+0xb1/0x5d0 fs/nilfs2/super.c:1047
nilfs_mount+0x613/0x9b0 fs/nilfs2/super.c:1317
...
In addition, since nilfs_sb2_bad_offset() performs multiplication without
considering the upper bound, the computation may overflow if the disk
layout parameters are not normal.
This fixes these issues by inserting preliminary sanity checks for those
parameters and by converting the comparison from one involving
multiplication and left bit-shifting to one using division and right
bit-shifting.
A use-after-free in acpi_ps_parse_aml() after a failing invocaion of
acpi_ds_call_control_method() is reported by KASAN [1] and code
inspection reveals that next_walk_state pushed to the thread by
acpi_ds_create_walk_state() is freed on errors, but it is not popped
from the thread beforehand. Thus acpi_ds_get_current_walk_state()
called by acpi_ps_parse_aml() subsequently returns it as the new
walk state which is incorrect.
To address this, make acpi_ds_call_control_method() call
acpi_ds_pop_walk_state() to pop next_walk_state from the thread before
returning an error.
The cause of the issue is that brelse() is called on both ofibh.sbh
and ofibh.ebh by udf_find_entry() when it returns NULL. However,
brelse() is called by udf_rename(), too. So, b_count on buffer_head
becomes unbalanced.
This patch fixes the issue by not calling brelse() by udf_rename()
when udf_find_entry() returns NULL.
Syzbot found a crash : UBSAN: shift-out-of-bounds in dbAllocAG. The
underlying bug is the missing check of bmp->db_agl2size. The field can
be greater than 64 and trigger the shift-out-of-bounds.
Fix this bug by adding a check of bmp->db_agl2size in dbMount since this
field is used in many following functions. The upper bound for this
field is L2MAXL2SIZE - L2MAXAG, thanks for the help of Dave Kleikamp.
Note that, for maintenance, I reorganized error handling code of dbMount.
Reported-by: syzbot+15342c1aa6a00fb7a438@syzkaller.appspotmail.com Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Changheon Lee reported TCP socket leaks, with a nice repro.
It seems we leak TCP sockets with the following sequence:
1) SOF_TIMESTAMPING_TX_ACK is enabled on the socket.
Each ACK will cook an skb put in error queue, from __skb_tstamp_tx().
__skb_tstamp_tx() is using skb_clone(), unless
SOF_TIMESTAMPING_OPT_TSONLY was also requested.
2) If the application is also using MSG_ZEROCOPY, then we put in the
error queue cloned skbs that had a struct ubuf_info attached to them.
Whenever an struct ubuf_info is allocated, sock_zerocopy_alloc()
does a sock_hold().
As long as the cloned skbs are still in sk_error_queue,
socket refcount is kept elevated.
3) Application closes the socket, while error queue is not empty.
Since tcp_close() no longer purges the socket error queue,
we might end up with a TCP socket with at least one skb in
error queue keeping the socket alive forever.
This bug can be (ab)used to consume all kernel memory
and freeze the host.
We need to purge the error queue, with proper synchronization
against concurrent writers.
Fixes: 24bcbe1cc69f ("net: stream: don't purge sk_error_queue in sk_stream_kill_queues()") Reported-by: Changheon Lee <darklight2357@icloud.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
"You don't have to, providing a 32bit data chunk without TCF_EM_SIMPLE
set will simply result in allocating & copy. It's an optimization,
nothing more."
So if an ematch module provides ops->datalen that means it wants a
complex data structure (saved in its em->data) instead of a simple u32
value. We should simply reject such a combination, otherwise this u32
could be misinterpreted as a pointer.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: syzbot+4caeae4c7103813598ae@syzkaller.appspotmail.com Reported-by: Jun Nie <jun.nie@linaro.org> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Extending the tail can have some unexpected side effects if a program uses
a helper like BPF_FUNC_skb_pull_data to read partial content beyond the
head skb headlen when all the skbs in the gso frag_list are linear with no
head_frag -
kernel BUG at net/core/skbuff.c:4219!
pc : skb_segment+0xcf4/0xd2c
lr : skb_segment+0x63c/0xd2c
Call trace:
skb_segment+0xcf4/0xd2c
__udp_gso_segment+0xa4/0x544
udp4_ufo_fragment+0x184/0x1c0
inet_gso_segment+0x16c/0x3a4
skb_mac_gso_segment+0xd4/0x1b0
__skb_gso_segment+0xcc/0x12c
udp_rcv_segment+0x54/0x16c
udp_queue_rcv_skb+0x78/0x144
udp_unicast_rcv_skb+0x8c/0xa4
__udp4_lib_rcv+0x490/0x68c
udp_rcv+0x20/0x30
ip_protocol_deliver_rcu+0x1b0/0x33c
ip_local_deliver+0xd8/0x1f0
ip_rcv+0x98/0x1a4
deliver_ptype_list_skb+0x98/0x1ec
__netif_receive_skb_core+0x978/0xc60
Fix this by marking these skbs as GSO_DODGY so segmentation can handle
the tail updates accordingly.
Fixes: 3dcbdb134f32 ("net: gso: Fix skb_segment splat when splitting gso_size mangled skb having linear-headed frag_list") Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com> Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Link: https://lore.kernel.org/r/1671084718-24796-1-git-send-email-quic_subashab@quicinc.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit mentioned below causes the ovs_flow_tbl_lookup() function
to be called with the masked key. However, it's supposed to be called
with the unmasked key. This due to the fact that the datapath supports
installing wider flows, and OVS relies on this behavior. For example
if ipv4(src=1.1.1.1/192.0.0.0, dst=1.1.1.2/192.0.0.0) exists, a wider
flow (smaller mask) of ipv4(src=192.1.1.1/128.0.0.0,dst=192.1.1.2/
128.0.0.0) is allowed to be added.
However, if we try to add a wildcard rule, the installation fails:
The reason is that the key used to determine if the flow is already
present in the system uses the original key ANDed with the mask.
This results in the IP address not being part of the (miniflow) key,
i.e., being substituted with an all-zero value. When doing the actual
lookup, this results in the key wrongfully matching the first flow,
and therefore the flow does not get installed.
This change reverses the commit below, but rather than having the key
on the stack, it's allocated.
Fixes: 190aa3e77880 ("openvswitch: Fix Frame-size larger than 1024 bytes warning.") Signed-off-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The problem occurs in probe process as follows:
r6040_init_one:
mdiobus_register
mdiobus_scan <- alloc and register phy_device,
the reference count of phy_device is 3
r6040_mii_probe
phy_connect <- connect to the first phy_device,
so the reference count of the first
phy_device is 4, others are 3
register_netdev <- fault inject succeeded, goto error handling path
// error handling path
err_out_mdio_unregister:
mdiobus_unregister(lp->mii_bus);
err_out_mdio:
mdiobus_free(lp->mii_bus); <- the reference count of the first
phy_device is 1, it is not released
and other phy_devices are released
// similarly, the remove process also has the same problem
The root cause is traced to the phy_device is not disconnected when
removes one r6040 device in r6040_remove_one() or on error handling path
after r6040_mii probed successfully. In r6040_mii_probe(), a net ethernet
device is connected to the first PHY device of mii_bus, in order to
notify the connected driver when the link status changes, which is the
default behavior of the PHY infrastructure to handle everything.
Therefore the phy_device should be disconnected when removes one r6040
device or on error handling path.
Fix it by adding phy_disconnect() when removes one r6040 device or on
error handling path after r6040_mii probed successfully.
Fixes: 3831861b4ad8 ("r6040: implement phylib") Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20221213125614.927754-1-lizetao1@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a slab-out-of-bounds read that occurs in nla_put() called from
nfc_genl_send_target() when target->sensb_res_len, which is duplicated
from an nfc_target in pn533, is too large as the nfc_target is not
properly initialized and retains garbage values. Clear nfc_targets with
memset() before they are used.
Fixes: 673088fb42d0 ("NFC: pn533: Send ATR_REQ directly for active device detection") Fixes: 361f3cb7f9cf ("NFC: DEP link hook implementation for pn533") Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20221214015139.119673-1-linuxlovemin@yonsei.ac.kr Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
skb_queue_purge() is called under spin_lock_irqsave() in handle_dmsg()
and hfcm_l1callback(), kfree_skb() is called in them, to fix this, use
skb_queue_splice_init() to move the dch->squeue to a free queue, also
enqueue the tx_skb and rx_skb, at last calling __skb_queue_purge() to
free the SKBs afer unlock.
Fixes: af69fb3a8ffa ("Add mISDN HFC multiport driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
skb_queue_purge() is called under spin_lock_irqsave() in hfcpci_l2l1D(),
kfree_skb() is called in it, to fix this, use skb_queue_splice_init()
to move the dch->squeue to a free queue, also enqueue the tx_skb and
rx_skb, at last calling __skb_queue_purge() to free the SKBs afer unlock.
Fixes: 1700fe1a10dc ("Add mISDN HFC PCI driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
skb_queue_purge() is called under spin_lock_irqsave() in hfcusb_l2l1D(),
kfree_skb() is called in it, to fix this, use skb_queue_splice_init()
to move the dch->squeue to a free queue, also enqueue the tx_skb and
rx_skb, at last calling __skb_queue_purge() to free the SKBs afer unlock.
In tx_iso_complete(), dev_kfree_skb() is called to consume the transmitted
SKB, so replace it with dev_consume_skb_irq().
Fixes: 69f52adb2d53 ("mISDN: Add HFC USB driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On error situation `clp->cl_cb_conn.cb_xprt` should not be given
a reference to the xprt otherwise both client cleanup and the
error handling path of the caller call to put it. Better to
delay handing over the reference to a later branch.
In check_all_cpu_dscr_defaults, opendir() opens the directory stream.
Add missing closedir() in the error path to release it.
In check_cpu_dscr_default, open() creates an open file descriptor.
Add missing close() in the error path to release it.
Fixes: ebd5858c904b ("selftests/powerpc: Add test for all DSCR sysfs interfaces") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20221205084429.570654-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on getPerfCountInfo v1.018 documentation, some of the
hv_gpci events were deprecated for platform firmware that
supports counter_info_version 0x8 or above.
Fix the hv_gpci event list by adding a new attribute group
called "hv_gpci_event_attrs_v6" and a "ENABLE_EVENTS_COUNTERINFO_V6"
macro to enable these events for platform firmware
that supports counter_info_version 0x6 or below. And assigning
the hv_gpci event list based on output counter info version
of underlying plaform.
If platform_device_add() is not called or failed, it can not call
platform_device_del() to clean up memory, it should call
platform_device_put() in error case.
Fixes: 26f6cb999366 ("[POWERPC] fsl_soc: add support for fsl_spi") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20221029111626.429971-1-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The interrupt frame detection and loads from the hypothetical pt_regs
are not bounds-checked. The next-frame validation only bounds-checks
STACK_FRAME_OVERHEAD, which does not include the pt_regs. Add another
test for this.
The user could set r1 to be equal to the address matching the first
interrupt frame - STACK_INT_FRAME_SIZE, which is in the previous page
due to the kernel redzone, and induce the kernel to load the marker from
there. Possibly this could cause a crash at least. If the user could
induce the previous page to contain a valid marker, then it might be
able to direct perf to read specific memory addresses in a way that
could be transmitted back to the user in the perf data.
Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically. It
needs to be freed when of_device_register() fails. Call put_device() to
give up the reference that's taken in device_initialize(), so that it
can be freed in kobject_cleanup() when the refcount hits 0.
macio device is freed in macio_release_dev(), so the kfree() can be
removed.
Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20221104032551.1075335-1-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The fsl_pamu_probe() returns directly when create_csd() failed, leaving
irq and memories unreleased.
Fix by jumping to error if create_csd() returns error.
On an iMX6ULL the following message appears when a wakealarm is set:
echo 0 > /sys/class/rtc/rtc1/wakealarm
rtc rtc1: Timeout trying to get valid LPSRT Counter read
This does not always happen but is reproducible quite often (7 out of 10
times). The problem appears because the iMX6ULL is not able to read the
registers within one 32kHz clock cycle which is the base clock of the
RTC. Therefore, this patch allows a difference of up to 320 cycles
(10ms). 10ms was chosen to be big enough even on systems with less cpu
power (e.g. iMX6ULL). According to the reference manual a difference is
fine:
- If the two consecutive reads are similar, the value is correct.
The values have to be similar, not equal.
Fixes: cd7f3a249dbe ("rtc: snvs: Add timeouts to avoid kernel lockups") Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by: Francesco Dolcini <francesco@dolcini.it> Link: https://lore.kernel.org/r/20221106115915.7930-1-francesco@dolcini.it Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit bc27fb68aaad ("include/uapi/linux/byteorder, swab: force inlining
of some byteswap operations") added __always_inline to swab functions
and commit 283d75737837 ("uapi/linux/stddef.h: Provide __always_inline to
userspace headers") added a definition of __always_inline for use in
exported headers when the kernel's compiler.h is not available.
However, since swab.h does not include stddef.h, if the header soup does
not indirectly include it, the definition of __always_inline is missing,
resulting in a compilation failure, which was observed compiling the
perf tool using exported headers containing this commit:
In file included from /usr/include/linux/byteorder/little_endian.h:12:0,
from /usr/include/asm/byteorder.h:14,
from tools/include/uapi/linux/perf_event.h:20,
from perf.h:8,
from builtin-bench.c:18:
/usr/include/linux/swab.h:160:8: error: unknown type name `__always_inline'
static __always_inline __u16 __swab16p(const __u16 *p)
Fix this by replacing the inclusion of linux/compiler.h with
linux/stddef.h to ensure that we pick up that definition if required,
without relying on it's indirect inclusion. compiler.h is then included
indirectly, via stddef.h.
Fixes: 283d75737837 ("uapi/linux/stddef.h: Provide __always_inline to userspace headers") Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Petr Vaněk <arkamar@atlas.cz> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ssi_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
ssi_pdriver is not unregistered.
Fix by unregister ssi_pdriver when the last platform_driver_register()
failed.
Fixes: 0fae198988b8 ("HSI: omap_ssi: built omap_ssi and omap_ssi_port into one module") Signed-off-by: Yuan Can <yuancan@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_add() succeeds, we should call device_del() when want to
get rid of it, so move it into proper jump symbol.
Otherwise, when __power_supply_register() returns fail and goto
wakeup_init_failed to exit, there is still residue device file in sysfs.
When attempt to probe device again, sysfs would complain as below:
If ssi_add_controller() returns error, it should call hsi_put_controller()
to give up the reference that was set in hsi_alloc_controller(), so that
it can call hsi_controller_release() to free controller and ports that
allocated in hsi_alloc_controller().
Fixes: b209e047bc74 ("HSI: Introduce OMAP SSI driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful uvesafb_init_mtrr() call, it must be
undone by a corresponding arch_phys_wc_del() call, as already done in the
remove function.
This has been added in the remove function in commit 63e28a7a5ffc
("uvesafb: Clean up MTRR code")
pci_get_device() will increase the reference count for the returned
pci_dev. For the error path, we need to use pci_dev_put() to decrease
the reference count.
Only a single out of three devices need a PWM, so from driver it's
optional. Moreover it's a single driver in the entire kernel that
currently selects PWM. Unfortunately this selection is a root cause
of the circular dependencies when we want to enable optional PWM
for some other drivers that select GPIOLIB.
Fixes: a2ed00da5047 ("drivers/video: add support for the Solomon SSD1307 OLED Controller") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The skb is delivered to netif_rx() in rtllib_monitor_rx(), which may free it,
after calling this, dereferencing skb may trigger use-after-free.
Found by Smatch.
Fixes: 94a799425eee ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20221123081253.22296-1-yuehaibing@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While doing fault injection test, I got the following report:
------------[ cut here ]------------
kobject: '(null)' (0000000039956980): is not initialized, yet kobject_put() is being called.
WARNING: CPU: 3 PID: 6306 at kobject_put+0x23d/0x4e0
CPU: 3 PID: 6306 Comm: 283 Tainted: G W 6.1.0-rc2-00005-g307c1086d7c9 #1253
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:kobject_put+0x23d/0x4e0
Call Trace:
<TASK>
cdev_device_add+0x15e/0x1b0
__iio_device_register+0x13b4/0x1af0 [industrialio]
__devm_iio_device_register+0x22/0x90 [industrialio]
max517_probe+0x3d8/0x6b4 [max517]
i2c_device_probe+0xa81/0xc00
When device_add() is injected fault and returns error, if dev->devt is not set,
cdev_add() is not called, cdev_del() is not needed. Fix this by checking dev->devt
in error path.
Fixes: 233ed09d7fda ("chardev: add helper function to register char devs with a struct device") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221202030237.520280-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If mcb_device_register() returns error in chameleon_parse_gdd(), the refcount
of bus and device name are leaked. Fix this by calling put_device() to give up
the reference, so they can be released in mcb_release_dev() and kobject_cleanup().
Fixes: 3764e82e5150 ("drivers: Introduce MEN Chameleon Bus") Reviewed-by: Johannes Thumshirn <jth@kernel.org> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Johannes Thumshirn <jth@kernel.org> Link: https://lore.kernel.org/r/ebfb06e39b19272f0197fa9136b5e4b6f34ad732.1669624063.git.johannes.thumshirn@wdc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() fails in cxl_pci_afu|adapter(), the device
is not added, device_unregister() can not be called in the error
path, otherwise it will cause a null-ptr-deref because of removing
not added device.
As comment of device_register() says, it should use put_device() to give
up the reference in the error path. So split device_unregister() into
device_del() and put_device(), then goes to put dev when register fails.
Fixes: f204e0b8cedd ("cxl: Driver code for powernv PCIe based cards for userspace access") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Frederic Barrat <fbarrat@linux.ibm.com> Acked-by: Andrew Donnellan <ajd@linux.ibm.com> Link: https://lore.kernel.org/r/20221111145440.2426970-2-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() fails in cxl_register_afu|adapter(), the device
is not added, device_unregister() can not be called in the error path,
otherwise it will cause a null-ptr-deref because of removing not added
device.
As comment of device_register() says, it should use put_device() to give
up the reference in the error path. So split device_unregister() into
device_del() and put_device(), then goes to put dev when register fails.
In some bad situation, the gts may be freed gru_check_chiplet_assignment.
The call chain can be gru_unload_context->gru_free_gru_context->gts_drop
and kfree finally. However, the caller didn't know if the gts is freed
or not and use it afterwards. This will trigger a Use after Free bug.
Fix it by introducing a return value to see if it's in error path or not.
Free the gts in caller if gru_check_chiplet_assignment check failed.
The sunsab_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
allocated sunsab_ports is leaked.
Fix by free sunsab_ports and set it to NULL when platform_driver_register()
failed.
As comment of pci_get_slot() says, it returns a pci_device with its
refcount increased. The caller must decrement the reference count by
calling pci_dev_put().
Since 'dma_dev' is only used to filter the channel in filter(), we can
call pci_dev_put() before exiting from pch_request_dma(). Add the
missing pci_dev_put() for the normal and error path.
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083b901f001794038a08b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
drivers/staging/vme_user/vme_tsi148.c:1757 tsi148_dma_list_add() warn:
'&entry->list' not removed from list
In tsi148_dma_list_add(), the error path "goto err_dma" will not
remove entry->list from list->entries, but entry will be freed,
then list traversal may cause UAF.
Fix by removeing it from list->entries before free().
The code in the FOTG210 driver isn't entirely endianness-agnostic
as reported by the kernel robot sparse testing. This came to
the surface while moving the files around.
The driver is only used on little-endian systems, so this causes
no real-world regression, but it is nice to be strict and have
some compile coverage also on big endian machines, so fix it
up with the right LE accessors.
This fixes a concurrency issue addressed in commit 34cb27528398 ("UIO: Fix
concurrency issue"):
"In a SMP case there was a race condition issue between
Uio_pdrv_genirq_irqcontrol() running on one CPU and irq handler on
another CPU. Fix it by spin_locking shared resources access inside irq
handler."
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
merged, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(), thus, both had the same concurrency issue
mentioned by the above commit. However, the above patch was only applied to
the "uio_pdrv_genirq" driver.
Split out from commit 34cb27528398 ("UIO: Fix concurrency issue").
Fixes: 0a0c3b5a24bd ("Add new uio device for dynamic memory allocation") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-3-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b74351287d4b ("uio: fix a sleep-in-atomic-context bug in
uio_dmem_genirq_irqcontrol()") started calling disable_irq() without
holding the spinlock because it can sleep. However, that fix introduced
another bug: if interrupt is already disabled and a new disable request
comes in, then the spinlock is not unlocked:
('myfpga' is a simple 'uio_dmem_genirq' driver I wrote to test this)
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
introduced, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(). Then commit 34cb27528398 ("UIO: Fix concurrency
issue"), which was only applied to "uio_pdrv_genirq", ended up making them
a little different. That commit, among other things, changed disable_irq()
to disable_irq_nosync() in the implementation of irqcontrol(). The
motivation there was to avoid a deadlock between irqcontrol() and
handler(), since it added a spinlock in the irq handler, and disable_irq()
waits for the completion of the irq handler.
By changing disable_irq() to disable_irq_nosync() in irqcontrol(), we also
avoid the sleeping-while-atomic bug that commit b74351287d4b ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") was trying to
fix. Thus, this fixes the missing unlock in irqcontrol() by importing the
implementation of irqcontrol() handler from the "uio_pdrv_genirq" driver.
In the end, it reverts commit b74351287d4b ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") and change
disable_irq() to disable_irq_nosync().
It is worth noting that this still does not address the concurrency issue
fixed by commit 34cb27528398 ("UIO: Fix concurrency issue"). It will be
addressed separately in the next commits.
Split out from commit 34cb27528398 ("UIO: Fix concurrency issue").
Fixes: b74351287d4b ("uio: fix a sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-2-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns error, the 'dev' and name needs be
freed. Add a release function, and then call put_device() in the
error path, so the name is freed in kobject_cleanup() and to the
'dev' is freed in release function.
Fixes: 2e4c77bea3d8 ("m68k: dio - Kill warn_unused_result warnings") Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221109064036.1835346-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are 2 ways to create IPoIB PKEY child interfaces:
1) Writing a PKEY to /sys/class/net/<ib parent interface>/create_child.
2) Using netlink with iproute.
While with sysfs the child interface has the same number of tx and
rx queues as the parent, with netlink there will always be 1 tx
and 1 rx queue for the child interface. That's because the
get_num_tx/rx_queues() netlink ops are missing and the default value
of 1 is taken for the number of queues (in rtnl_create_link()).
This change adds the get_num_tx/rx_queues() ops which allows for
interfaces with multiple queues to be created over netlink. This
constant only represents the max number of tx and rx queues on that
net device.
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. We add a new struct
'amd_geode_priv' to record pointer of the pci_dev and membase, and then
add missing pci_dev_put() for the normal and error path.
Fixes: ef5d862734b8 ("[PATCH] Add Geode HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the normal and error path.
Fixes: 96d63c0297cc ("[PATCH] Add AMD HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/scsi/snic/snic_disc.c:307 snic_tgt_create() warn:
'&tgt->list' not removed from list
If device_add() fails in snic_tgt_create(), tgt will be freed, but
tgt->list will not be removed from snic->disc.tgt_list, then list traversal
may cause UAF.
Remove from snic->disc.tgt_list before free().
Fixes: c8806b6c9e82 ("snic: driver for Cisco SCSI HBA") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221117035100.2944812-1-cuigaosheng1@huawei.com Acked-by: Narsimhulu Musini <nmusini@cisco.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fcoe_init() calls fcoe_transport_attach(&fcoe_sw_transport), but when
fcoe_if_init() fails, &fcoe_sw_transport is not detached and leaves freed
&fcoe_sw_transport on fcoe_transports list. This causes panic when
reinserting module.
BUG: unable to handle page fault for address: fffffbfff82e2213
RIP: 0010:fcoe_transport_attach+0xe1/0x230 [libfcoe]
Call Trace:
<TASK>
do_one_initcall+0xd0/0x4e0
load_module+0x5eee/0x7210
...
Fixes: 78a582463c1e ("[SCSI] fcoe: convert fcoe.ko to become an fcoe transport provider driver") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221115092442.133088-1-chenzhongjin@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ipr_init() will not call unregister_reboot_notifier() when
pci_register_driver() fails, which causes a WARNING. Call
unregister_reboot_notifier() when pci_register_driver() fails.
If device_register() returns an error, the name allocated by dev_set_name()
needs to be freed. As the comment of device_register() says, one should use
put_device() to give up the reference in the error path. Fix this by
calling put_device(), then the name can be freed in kobject_cleanup().
The 'fcf' is freed in fcoe_fcf_device_release(), so the kfree() in the
error path can be removed.
The 'ctlr' is freed in fcoe_ctlr_device_release(), so don't use the error
label, just return NULL after calling put_device().
Fixes: 9a74e884ee71 ("[SCSI] libfcoe: Add fcoe_sysfs") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221112094310.3633291-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hpsa_sas_port_add_rphy() returns an error, the 'rphy' allocated in
sas_end_device_alloc() needs to be freed. Address this by calling
sas_rphy_free() in the error path.
Fixes: d04e62b9d63a ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221111043012.1074466-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hpsa_sas_port_add_phy() returns an error, hpsa_free_sas_phy() can not be
called to free the memory because the port and the phy have not been added
yet.
Replace hpsa_free_sas_phy() with sas_phy_free() and kfree() to avoid kernel
crash in this case.
Fixes: d04e62b9d63a ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221110151129.394389-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the MAC is connected to a 10 Mb/s PHY and the PTP clock is derived
from the MAC reference clock (default), the clk_ptp_rate becomes too
small and the calculated sub second increment becomes 0 when computed by
the stmmac_config_sub_second_increment() function within
stmmac_init_tstamp_counter().
Therefore, the subsequent div_u64 in stmmac_init_tstamp_counter()
operation triggers a divide by 0 exception as shown below.
[ 95.062067] socfpga-dwmac ff700000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 95.076440] socfpga-dwmac ff700000.ethernet eth0: PHY [stmmac-0:08] driver [NCN26000] (irq=49)
[ 95.095964] dwmac1000: Master AXI performs any burst length
[ 95.101588] socfpga-dwmac ff700000.ethernet eth0: No Safety Features support found
[ 95.109428] Division by zero in kernel.
[ 95.113447] CPU: 0 PID: 239 Comm: ifconfig Not tainted 6.1.0-rc7-centurion3-1.0.3.0-01574-gb624218205b7-dirty #77
[ 95.123686] Hardware name: Altera SOCFPGA
[ 95.127695] unwind_backtrace from show_stack+0x10/0x14
[ 95.132938] show_stack from dump_stack_lvl+0x40/0x4c
[ 95.137992] dump_stack_lvl from Ldiv0+0x8/0x10
[ 95.142527] Ldiv0 from __aeabi_uidivmod+0x8/0x18
[ 95.147232] __aeabi_uidivmod from div_u64_rem+0x1c/0x40
[ 95.152552] div_u64_rem from stmmac_init_tstamp_counter+0xd0/0x164
[ 95.158826] stmmac_init_tstamp_counter from stmmac_hw_setup+0x430/0xf00
[ 95.165533] stmmac_hw_setup from __stmmac_open+0x214/0x2d4
[ 95.171117] __stmmac_open from stmmac_open+0x30/0x44
[ 95.176182] stmmac_open from __dev_open+0x11c/0x134
[ 95.181172] __dev_open from __dev_change_flags+0x168/0x17c
[ 95.186750] __dev_change_flags from dev_change_flags+0x14/0x50
[ 95.192662] dev_change_flags from devinet_ioctl+0x2b4/0x604
[ 95.198321] devinet_ioctl from inet_ioctl+0x1ec/0x214
[ 95.203462] inet_ioctl from sock_ioctl+0x14c/0x3c4
[ 95.208354] sock_ioctl from vfs_ioctl+0x20/0x38
[ 95.212984] vfs_ioctl from sys_ioctl+0x250/0x844
[ 95.217691] sys_ioctl from ret_fast_syscall+0x0/0x4c
[ 95.222743] Exception stack(0xd0ee1fa8 to 0xd0ee1ff0)
[ 95.227790] 1fa0: 00574c4fbe9aeca40000000300008914be9aeca4be9aec50
[ 95.235945] 1fc0: 00574c4fbe9aeca40059f07800000036be9aee8cbe9aef7a0000001500000000
[ 95.244096] 1fe0: 005a01f0be9aec38004d7484b6e67d74
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 9238f36a5a50 ("Bluetooth: Add request cmd_complete and cmd_status functions") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 43eb12d78960 ("Bluetooth: Fix/implement Three-wire reliable packet sending") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 0ff252c1976d ("Bluetooth: hciuart: Add support QCA chipset for UART") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 803b58367ffb ("Bluetooth: btusb: Implement driver internal packet reassembly") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
TX/RX callback handlers (ntb_netdev_tx_handler(),
ntb_netdev_rx_handler()) can be called in interrupt
context via the DMA framework when the respective
DMA operations have completed. As such, any calls
by these routines to free skb's, should use the
interrupt context safe dev_kfree_skb_any() function.
Previously, these callback handlers would call the
interrupt unsafe version of dev_kfree_skb(). This has
not presented an issue on Intel IOAT DMA engines as
that driver utilizes tasklets rather than a hard
interrupt handler, like the AMD PTDMA DMA driver.
On AMD systems, a kernel WARNING message is
encountered, which is being issued from
skb_release_head_state() due to in_hardirq()
being true.
Besides the user visible WARNING from the kernel,
the other symptom of this bug was that TCP/IP performance
across the ntb_netdev interface was very poor, i.e.
approximately an order of magnitude below what was
expected. With the repair to use dev_kfree_skb_any(),
kernel WARNINGs from skb_release_head_state() ceased
and TCP/IP performance, as measured by iperf, was on
par with expected results, approximately 20 Gb/s on
AMD Milan based server. Note that this performance
is comparable with Intel based servers.
Fixes: 765ccc7bc3d91 ("ntb_netdev: correct skb leak") Fixes: 548c237c0a997 ("net: Add support for NTB virtual ethernet device") Signed-off-by: Eric Pilmore <epilmore@gigaio.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20221209000659.8318-1-epilmore@gigaio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In these two cases, dev_kfree_skb() is called consume the xmited SKB,
so replace it with dev_consume_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In scc_discard_buffers(), dev_kfree_skb() is called to discard the SKBs,
so replace it with dev_kfree_skb_irq().
In scc_net_tx(), dev_kfree_skb() is called to drop the SKB that exceed
queue length, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
In this case, the lock is used to protected 'bp', so we can move
dev_kfree_skb() after the spin_unlock_irqrestore().
Fixes: 4796417417a6 ("dnet: Dave DNET ethernet controller driver (updated)") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in xemaclite_tx_timeout() to
drop the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: bb81b2ddfa19 ("net: add Xilinx emac lite device driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in bmac_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in mace_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a race condition in vxlan that when deleting a vxlan device
during receiving packets, there is a possibility that the sock is
released after getting vxlan_sock vs from sk_user_data. Then in
later vxlan_ecn_decapsulate(), vxlan_get_sk_family() we will got
NULL pointer dereference. e.g.
Fix this by waiting for all sk_user_data reader to finish before
releasing the sock.
Reported-by: Jianlin Shi <jishi@redhat.com> Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Fixes: 6a93cc905274 ("udp-tunnel: Add a few more UDP tunnel APIs") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is traced to the netdev and fst_card_info are not freed
when removes one fst in fst_remove_one(), which may trigger oom if
repeated insmod and rmmod module.
Fix it by adding free_netdev() and kfree() in fst_remove_one(), just as
the operations on the error handling path in fst_add_one().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in free_tx_buffers() to drop
the SKBs in tx buffers, when the card is down, so replace it with
dev_kfree_skb_irq() here.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If vp alloc failed in qlcnic_sriov_init(), all previously allocated vp
needs to be freed.
Fixes: f197a7aa6288 ("qlcnic: VF-PF communication channel implementation") Signed-off-by: Yuan Can <yuancan@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
vmci_transport_dgram_enqueue() does not check the return value
of memcpy_from_msg(). If memcpy_from_msg() fails, it is possible that
uninitialized memory contents are sent unintentionally instead of user's
message in the datagram to the destination. Return with an error if
memcpy_from_msg() fails.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f7db23a07af ("vmci_transport: switch ->enqeue_dgram, ->enqueue_stream and ->dequeue_stream to msghdr") Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Vishnu Dasa <vdasa@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the blk_classic option is enabled, non-blktrace events must be
filtered out. Otherwise, events of other types are output in the blktrace
classic format, which is unexpected.
The problem can be triggered in the following ways:
Fix to return a negative error code instead of 0 when
brcmf_chip_set_active() fails. In addition, change the return
value for brcmf_pcie_exit_download_state() to keep consistent.
Fixes: d380ebc9b6fb ("brcmfmac: rename chip download functions") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1669959342-27144-1-git-send-email-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
As the coda_iram_alloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
In configure_channels(), we should call of_node_put() when breaking
out of for_each_child_of_node() which will automatically increase
and decrease the refcount.
Fixes: c5f5d0f99794 ("[media] c8sectpfe: STiH407/10 Linux DVB demux support") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
