After a bus fault, capture and log the chip registers immediately, if the
NDEBUG_PSEUDO_DMA macro is defined. Remove some printk(KERN_DEBUG ...)
messages that aren't needed any more. Don't skip the debug message when
bytes == 0. Show all of the byte counters in the debug messages.
Currently amdgpu takes backlight caps provided by the ACPI tables
on systems as is. If the firmware sets maximums that are too low
this means that users don't get a good experience.
To avoid having to maintain a quirk list of such systems, do a sanity
check on the values. Check that the spread is at least half of the
values that amdgpu would use if no ACPI table was found and if not
use the amdgpu defaults.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3020 Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
The calculated vtotal may has 1 line deviation. To get precisely
vtotal number, round the vtotal result.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Anthony Koo <anthony.koo@amd.com> Signed-off-by: Robin Chen <robin.chen@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Gen6 devices have the same problem and the same Solution as the Gen5
ones.
Some TongFang barebones have touchpad and/or keyboard issues after
suspend, fixable with nomux + reset + noloop + nopnp. Luckily, none of
them have an external PS/2 port so this can safely be set for all of
them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
Some TongFang barebones have touchpad and/or keyboard issues after
suspend, fixable with nomux + reset + noloop + nopnp. Luckily, none of
them have an external PS/2 port so this can safely be set for all of
them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
As Fedor Pchelkin pointed out, this commit violates the
convention of using the macro return value, which causes errors.
For example, in functions tda18271_attach(), xc5000_attach(),
simple_tuner_attach().
Link: https://lore.kernel.org/linux-media/20240424202031.syigrtrtipbq5f2l@fpc/ Suggested-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Roman Smirnov <r.smirnov@omp.ru> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return devm_of_clk_add_hw_provider() in order to transfer the error, if it
fails due to resource allocation failure or device tree clock provider
registration failure.
Cc: stable@vger.kernel.org Fixes: ebbfabc16d23 ("ASoC: rt5682: Add CCF usage for providing I2S clks") Signed-off-by: Ma Ke <make24@iscas.ac.cn> Link: https://patch.msgid.link/20240830143154.3448004-1-make24@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MSGF_LEG_MASK is laid out with INTA in bit 0, INTB in bit 1, INTC in bit 2,
and INTD in bit 3. Hardware IRQ numbers start at 0, and we register
PCI_NUM_INTX IRQs. So to enable INTA (aka hwirq 0) we should set bit 0.
Remove the subtraction of one.
This bug would cause INTx interrupts not to be delivered, as enabling INTB
would actually enable INTA, and enabling INTA wouldn't enable anything at
all. It is likely that this got overlooked for so long since most PCIe
hardware uses MSIs. This fixes the following UBSAN error:
UBSAN: shift-out-of-bounds in ../drivers/pci/controller/pcie-xilinx-nwl.c:389:11
shift exponent 18446744073709551615 is too large for 32-bit type 'int'
CPU: 1 PID: 61 Comm: kworker/u10:1 Not tainted 6.6.20+ #268
Hardware name: xlnx,zynqmp (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace (arch/arm64/kernel/stacktrace.c:235)
show_stack (arch/arm64/kernel/stacktrace.c:242)
dump_stack_lvl (lib/dump_stack.c:107)
dump_stack (lib/dump_stack.c:114)
__ubsan_handle_shift_out_of_bounds (lib/ubsan.c:218 lib/ubsan.c:387)
nwl_unmask_leg_irq (drivers/pci/controller/pcie-xilinx-nwl.c:389 (discriminator 1))
irq_enable (kernel/irq/internals.h:234 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345)
__irq_startup (kernel/irq/internals.h:239 kernel/irq/chip.c:180 kernel/irq/chip.c:250)
irq_startup (kernel/irq/chip.c:270)
__setup_irq (kernel/irq/manage.c:1800)
request_threaded_irq (kernel/irq/manage.c:2206)
pcie_pme_probe (include/linux/interrupt.h:168 drivers/pci/pcie/pme.c:348)
Fixes: 9a181e1093af ("PCI: xilinx-nwl: Modify IRQ chip for legacy interrupts") Link: https://lore.kernel.org/r/20240531161337.864994-3-sean.anderson@linux.dev Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3f1b0e1f2875 (".gitignore update") added *.orig and *.rej
patterns to .gitignore in v2.6.23. The commit message didn't give a
rationale. Later on, commit 1f5d3a6b6532 ("Remove *.rej pattern from
.gitignore") removed the *.rej pattern in v2.6.26, on the rationale that
*.rej files indicated something went really wrong and should not be
ignored.
The *.rej files are now shown by `git status`, which helps located
conflicts when applying patches and lowers the probability that they
will go unnoticed. It is however still easy to overlook the *.orig files
which slowly polute the source tree. That's not as big of a deal as not
noticing a conflict, but it's still not nice.
Drop the *.orig pattern from .gitignore to avoid this and help keep the
source tree clean.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[masahiroy@kernel.org:
I do not have a strong opinion about this. Perhaps some people may have
a different opinion.
If you are someone who wants to ignore *.orig, it is likely you would
want to do so across all projects. Then, $XDG_CONFIG_HOME/git/ignore
would be more suitable for your needs. gitignore(5) suggests, "Patterns
which a user wants Git to ignore in all situations generally go into a
file specified by core.excludesFile in the user's ~/.gitconfig".
Please note that you cannot do the opposite; if *.orig is ignored by
the project's .gitignore, you cannot override the decision because
$XDG_CONFIG_HOME/git/ignore has a lower priority.
If *.orig is sitting on the fence, I'd leave it to the users. ] Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Gresko reports that the root user on an NFS client is able to
change the security labels on files on an NFS filesystem that is
exported with root squashing enabled.
The end of the kerneldoc comment for __vfs_setxattr_noperm() states:
* This function requires the caller to lock the inode's i_mutex before it
* is executed. It also assumes that the caller will make the appropriate
* permission checks.
nfsd_setattr() does do permissions checking via fh_verify() and
nfsd_permission(), but those don't do all the same permissions checks
that are done by security_inode_setxattr() and its related LSM hooks do.
Since nfsd_setattr() is the only consumer of security_inode_setsecctx(),
simplest solution appears to be to replace the call to
__vfs_setxattr_noperm() with a call to __vfs_setxattr_locked(). This
fixes the above issue and has the added benefit of causing nfsd to
recall conflicting delegations on a file when a client tries to change
its security label.
Cc: stable@kernel.org Reported-by: Marek Gresko <marek.gresko@protonmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=218809 Signed-off-by: Scott Mayhew <smayhew@redhat.com> Tested-by: Stephen Smalley <stephen.smalley.work@gmail.com> Reviewed-by: Stephen Smalley <stephen.smalley.work@gmail.com> Reviewed-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Acked-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Paul Moore <paul@paul-moore.com>
[Shivani: Modified to apply on v5.15.y-v6.1.y] Signed-off-by: Shivani Agarwal <shivani.agarwal@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New CPU #defines encode vendor and family as well as model.
[ dhansen: vertically align 0's in invlpg_miss_ids[] ]
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/all/20240424181518.41946-1-tony.luck%40intel.com
[ Ricardo: I used the old match macro X86_MATCH_INTEL_FAM6_MODEL()
instead of X86_MATCH_VFM() as in the upstream commit.
I also kept the ALDERLAKE_N name instead of ATOM_GRACEMONT. Both refer
to the same CPU model. ] Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current initialization of the struct x86_cpu_id via
pl4_support_ids[] is partial and wrong. It is initializing
"stepping" field with "X86_FEATURE_ANY" instead of "feature" field.
Use X86_MATCH_INTEL_FAM6_MODEL macro instead of initializing
each field of the struct x86_cpu_id for pl4_supported list of CPUs.
This X86_MATCH_INTEL_FAM6_MODEL macro internally uses another macro
X86_MATCH_VENDOR_FAM_MODEL_FEATURE for X86 based CPU matching with
appropriate initialized values.
Reported-by: Dave Hansen <dave.hansen@intel.com> Link: https://lore.kernel.org/lkml/28ead36b-2d9e-1a36-6f4e-04684e420260@intel.com Fixes: eb52bc2ae5b8 ("powercap: RAPL: Add Power Limit4 support for Meteor Lake SoC") Fixes: b08b95cf30f5 ("powercap: RAPL: Add Power Limit4 support for Alder Lake-N and Raptor Lake-P") Fixes: 515755906921 ("powercap: RAPL: Add Power Limit4 support for RaptorLake") Fixes: 1cc5b9a411e4 ("powercap: Add Power Limit4 support for Alder Lake SoC") Fixes: 8365a898fe53 ("powercap: Add Power Limit4 support") Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[ Ricardo: I only kept TIGERLAKE, ALDERLAKE, and ALDERLAKE_L in
pl4_support_ids as only these models are enumerated before this
changeset. ] Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only provide ctnetlink_label_size when it is used,
which is when CONFIG_NF_CONNTRACK_EVENTS is configured.
Flagged by clang-18 W=1 builds as:
.../nf_conntrack_netlink.c:385:19: warning: unused function 'ctnetlink_label_size' [-Wunused-function]
385 | static inline int ctnetlink_label_size(const struct nf_conn *ct)
| ^~~~~~~~~~~~~~~~~~~~
The condition on CONFIG_NF_CONNTRACK_LABELS being removed by
this patch guards compilation of non-trivial implementations
of ctnetlink_dump_labels() and ctnetlink_label_size().
However, this is not necessary as each of these functions
will always return 0 if CONFIG_NF_CONNTRACK_LABELS is not defined
as each function starts with the equivalent of:
And nf_ct_labels_find always returns NULL if CONFIG_NF_CONNTRACK_LABELS
is not enabled. So I believe that the compiler optimises the code away
in such cases anyway.
Found by inspection.
Compile tested only.
Originally splitted in two patches, Pablo Neira Ayuso collapsed them and
added Fixes: tag.
Fixes: 0ceabd83875b ("netfilter: ctnetlink: deliver labels to userspace") Link: https://lore.kernel.org/netfilter-devel/20240909151712.GZ2097826@kernel.org/ Signed-off-by: Simon Horman <horms@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Documentation of list_del_rcu() warns callers to not immediately free
the deleted list item. While it seems not necessary to use the
RCU-variant of list_del() here in the first place, doing so seems to
require calling kfree_rcu() on the deleted item as well.
Fixes: 3f0465a9ef02 ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a WARNING in bond_xdp_get_xmit_slave. To reproduce
this[1], one bond device (bond1) has xdpdrv, which increases
bpf_master_redirect_enabled_key. Another bond device (bond0) which is
unsupported by XDP but its slave (veth3) has xdpgeneric that returns
XDP_TX. This triggers WARN_ON_ONCE() from the xdp_master_redirect().
To reduce unnecessary warnings and improve log management, we need to
delete the WARN_ON_ONCE() and add ratelimit to the netdev_err().
[1] Steps to reproduce:
# Needs tx_xdp with return XDP_TX;
ip l add veth0 type veth peer veth1
ip l add veth3 type veth peer veth4
ip l add bond0 type bond mode 6 # BOND_MODE_ALB, unsupported by XDP
ip l add bond1 type bond # BOND_MODE_ROUNDROBIN by default
ip l set veth0 master bond1
ip l set bond1 up
# Increases bpf_master_redirect_enabled_key
ip l set dev bond1 xdpdrv object tx_xdp.o section xdp_tx
ip l set veth3 master bond0
ip l set bond0 up
ip l set veth4 up
# Triggers WARN_ON_ONCE() from the xdp_master_redirect()
ip l set veth3 xdpgeneric object tx_xdp.o section xdp_tx
Reported-by: syzbot+c187823a52ed505b2257@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=c187823a52ed505b2257 Fixes: 9e2ee5c7e7c3 ("net, bonding: Add XDP support to the bonding driver") Signed-off-by: Jiwon Kim <jiwonaid0@gmail.com> Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20240918140602.18644-1-jiwonaid0@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When broadcasting data to multiple nodes via MHI, using skb_clone()
causes all nodes to receive the same header data. This can result in
packets being discarded by endpoints, leading to lost data.
This issue occurs when a socket is closed, and a QRTR_TYPE_DEL_CLIENT
packet is broadcasted. All nodes receive the same destination node ID,
causing the node connected to the client to discard the packet and
remain unaware of the client's deletion.
Replace skb_clone() with pskb_copy(), to create a separate copy of
the header for each sk_buff.
Fixes: bdabad3e363d ("net: Add Qualcomm IPC router") Signed-off-by: Youssef Samir <quic_yabdulra@quicinc.com> Reviewed-by: Jeffery Hugo <quic_jhugo@quicinc.com> Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com> Reviewed-by: Chris Lew <quic_clew@quicinc.com> Link: https://patch.msgid.link/20240916170858.2382247-1-quic_yabdulra@quicinc.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We have some machines running stock Ubuntu 20.04.6 which is their 5.4.0-174-generic
kernel that are running ceph and recently hit a null ptr dereference in
tcp_rearm_rto(). Initially hitting it from the TLP path, but then later we also
saw it getting hit from the RACK case as well. Here are examples of the oops
messages we saw in each of those cases:
After we hit this we disabled TLP by setting tcp_early_retrans to 0 and then hit the crash in the RACK case:
Aug 7 07:26:16 rx [1006006.265582] BUG: kernel NULL pointer dereference, address: 0000000000000020
Aug 7 07:26:16 rx [1006006.272719] #PF: supervisor read access in kernel mode
Aug 7 07:26:16 rx [1006006.278030] #PF: error_code(0x0000) - not-present page
Aug 7 07:26:16 rx [1006006.283343] PGD 0 P4D 0
Aug 7 07:26:16 rx [1006006.286057] Oops: 0000 [#1] SMP NOPTI
Aug 7 07:26:16 rx [1006006.289896] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G W 5.4.0-174-generic #193-Ubuntu
Aug 7 07:26:16 rx [1006006.299107] Hardware name: Supermicro SMC 2x26 os-gen8 64C NVME-Y 256G/H12SSW-NTR, BIOS 2.5.V1.2U.NVMe.UEFI 05/09/2023
Aug 7 07:26:16 rx [1006006.309970] RIP: 0010:tcp_rearm_rto+0xe4/0x160
Aug 7 07:26:16 rx [1006006.314584] Code: 87 ca 04 00 00 00 5b 41 5c 41 5d 5d c3 c3 49 8b bc 24 40 06 00 00 eb 8d 48 bb cf f7 53 e3 a5 9b c4 20 4c 89 ef e8 0c fe 0e 00 <48> 8b 78 20 48 c1 ef 03 48 89 f8 41 8b bc 24 80 04 00 00 48 f7 e3
Aug 7 07:26:16 rx [1006006.333499] RSP: 0018:ffffb42600a50960 EFLAGS: 00010246
Aug 7 07:26:16 rx [1006006.338895] RAX: 0000000000000000 RBX: 20c49ba5e353f7cf RCX: 0000000000000000
Aug 7 07:26:16 rx [1006006.346193] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff92d687ed8160
Aug 7 07:26:16 rx [1006006.353489] RBP: ffffb42600a50978 R08: 0000000000000000 R09: 00000000cd896dcc
Aug 7 07:26:16 rx [1006006.360786] R10: ffff92dc3404f400 R11: 0000000000000001 R12: ffff92d687ed8000
Aug 7 07:26:16 rx [1006006.368084] R13: ffff92d687ed8160 R14: 00000000cd896dcc R15: 00000000cd8fca81
Aug 7 07:26:16 rx [1006006.375381] FS: 0000000000000000(0000) GS:ffff93158ad40000(0000) knlGS:0000000000000000
Aug 7 07:26:16 rx [1006006.383632] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Aug 7 07:26:16 rx [1006006.389544] CR2: 0000000000000020 CR3: 0000003e775ce006 CR4: 0000000000760ee0
Aug 7 07:26:16 rx [1006006.396839] PKRU: 55555554
Aug 7 07:26:16 rx [1006006.399717] Call Trace:
Aug 7 07:26:16 rx [1006006.402335]
Aug 7 07:26:16 rx [1006006.404525] ? show_regs.cold+0x1a/0x1f
Aug 7 07:26:16 rx [1006006.408532] ? __die+0x90/0xd9
Aug 7 07:26:16 rx [1006006.411760] ? no_context+0x196/0x380
Aug 7 07:26:16 rx [1006006.415599] ? __bad_area_nosemaphore+0x50/0x1a0
Aug 7 07:26:16 rx [1006006.420392] ? _raw_spin_lock+0x1e/0x30
Aug 7 07:26:16 rx [1006006.424401] ? bad_area_nosemaphore+0x16/0x20
Aug 7 07:26:16 rx [1006006.428927] ? do_user_addr_fault+0x267/0x450
Aug 7 07:26:16 rx [1006006.433450] ? __do_page_fault+0x58/0x90
Aug 7 07:26:16 rx [1006006.437542] ? do_page_fault+0x2c/0xe0
Aug 7 07:26:16 rx [1006006.441470] ? page_fault+0x34/0x40
Aug 7 07:26:16 rx [1006006.445134] ? tcp_rearm_rto+0xe4/0x160
Aug 7 07:26:16 rx [1006006.449145] tcp_ack+0xa32/0xb30
Aug 7 07:26:16 rx [1006006.452542] tcp_rcv_established+0x13c/0x670
Aug 7 07:26:16 rx [1006006.456981] ? sk_filter_trim_cap+0x48/0x220
Aug 7 07:26:16 rx [1006006.461419] tcp_v6_do_rcv+0xdb/0x450
Aug 7 07:26:16 rx [1006006.465257] tcp_v6_rcv+0xc2b/0xd10
Aug 7 07:26:16 rx [1006006.468918] ip6_protocol_deliver_rcu+0xd3/0x4e0
Aug 7 07:26:16 rx [1006006.473706] ip6_input_finish+0x15/0x20
Aug 7 07:26:16 rx [1006006.477710] ip6_input+0xa2/0xb0
Aug 7 07:26:16 rx [1006006.481109] ? ip6_protocol_deliver_rcu+0x4e0/0x4e0
Aug 7 07:26:16 rx [1006006.486151] ip6_sublist_rcv_finish+0x3d/0x50
Aug 7 07:26:16 rx [1006006.490679] ip6_sublist_rcv+0x1aa/0x250
Aug 7 07:26:16 rx [1006006.494779] ? ip6_rcv_finish_core.isra.0+0xa0/0xa0
Aug 7 07:26:16 rx [1006006.499828] ipv6_list_rcv+0x112/0x140
Aug 7 07:26:16 rx [1006006.503748] __netif_receive_skb_list_core+0x1a4/0x250
Aug 7 07:26:16 rx [1006006.509057] netif_receive_skb_list_internal+0x1a1/0x2b0
Aug 7 07:26:16 rx [1006006.514538] gro_normal_list.part.0+0x1e/0x40
Aug 7 07:26:16 rx [1006006.519068] napi_complete_done+0x91/0x130
Aug 7 07:26:16 rx [1006006.523352] mlx5e_napi_poll+0x18e/0x610 [mlx5_core]
Aug 7 07:26:16 rx [1006006.528481] net_rx_action+0x142/0x390
Aug 7 07:26:16 rx [1006006.532398] __do_softirq+0xd1/0x2c1
Aug 7 07:26:16 rx [1006006.536142] irq_exit+0xae/0xb0
Aug 7 07:26:16 rx [1006006.539452] do_IRQ+0x5a/0xf0
Aug 7 07:26:16 rx [1006006.542590] common_interrupt+0xf/0xf
Aug 7 07:26:16 rx [1006006.546421]
Aug 7 07:26:16 rx [1006006.548695] RIP: 0010:native_safe_halt+0xe/0x10
Aug 7 07:26:16 rx [1006006.553399] Code: 7b ff ff ff eb bd 90 90 90 90 90 90 e9 07 00 00 00 0f 00 2d 36 2c 50 00 f4 c3 66 90 e9 07 00 00 00 0f 00 2d 26 2c 50 00 fb f4 90 0f 1f 44 00 00 55 48 89 e5 41 55 41 54 53 e8 dd 5e 61 ff 65
Aug 7 07:26:16 rx [1006006.572309] RSP: 0018:ffffb42600177e70 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffc2
Aug 7 07:26:16 rx [1006006.580040] RAX: ffffffff8ed08b20 RBX: 0000000000000005 RCX: 0000000000000001
Aug 7 07:26:16 rx [1006006.587337] RDX: 00000000f48eeca2 RSI: 0000000000000082 RDI: 0000000000000082
Aug 7 07:26:16 rx [1006006.594635] RBP: ffffb42600177e90 R08: 0000000000000000 R09: 000000000000020f
Aug 7 07:26:16 rx [1006006.601931] R10: 0000000000100000 R11: 0000000000000000 R12: 0000000000000005
Aug 7 07:26:16 rx [1006006.609229] R13: ffff93157deb5f00 R14: 0000000000000000 R15: 0000000000000000
Aug 7 07:26:16 rx [1006006.616530] ? __cpuidle_text_start+0x8/0x8
Aug 7 07:26:16 rx [1006006.620886] ? default_idle+0x20/0x140
Aug 7 07:26:16 rx [1006006.624804] arch_cpu_idle+0x15/0x20
Aug 7 07:26:16 rx [1006006.628545] default_idle_call+0x23/0x30
Aug 7 07:26:16 rx [1006006.632640] do_idle+0x1fb/0x270
Aug 7 07:26:16 rx [1006006.636035] cpu_startup_entry+0x20/0x30
Aug 7 07:26:16 rx [1006006.640126] start_secondary+0x178/0x1d0
Aug 7 07:26:16 rx [1006006.644218] secondary_startup_64+0xa4/0xb0
Aug 7 07:26:17 rx [1006006.648568] Modules linked in: vrf bridge stp llc vxlan ip6_udp_tunnel udp_tunnel nls_iso8859_1 nft_ct amd64_edac_mod edac_mce_amd kvm_amd kvm crct10dif_pclmul ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper wmi_bmof ipmi_ssif input_leds joydev rndis_host cdc_ether usbnet ast mii drm_vram_helper ttm drm_kms_helper i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt ccp mac_hid ipmi_si ipmi_devintf ipmi_msghandler sch_fq_codel nf_tables_set nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink ramoops reed_solomon efi_pstore drm ip_tables x_tables autofs4 raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid0 multipath linear mlx5_ib ib_uverbs ib_core raid1 hid_generic mlx5_core pci_hyperv_intf crc32_pclmul usbhid ahci tls mlxfw bnxt_en hid libahci nvme i2c_piix4 nvme_core wmi [last unloaded: cpuid]
Aug 7 07:26:17 rx [1006006.726180] CR2: 0000000000000020
Aug 7 07:26:17 rx [1006006.729718] ---[ end trace e0e2e37e4e612984 ]---
Prior to seeing the first crash and on other machines we also see the warning in
tcp_send_loss_probe() where packets_out is non-zero, but both transmit and retrans
queues are empty so we know the box is seeing some accounting issue in this area:
The NULL ptr deref is coming from tcp_rto_delta_us() attempting to pull an skb
off the head of the retransmit queue and then dereferencing that skb to get the
skb_mstamp_ns value via tcp_skb_timestamp_us(skb).
The crash is the same one that was reported a # of years ago here:
https://lore.kernel.org/netdev/86c0f836-9a7c-438b-d81a-839be45f1f58@gmail.com/T/#t
and the kernel we're running has the fix which was added to resolve this issue.
Unfortunately we've been unsuccessful so far in reproducing this problem in the
lab and do not have the luxury of pushing out a new kernel to try and test if
newer kernels resolve this issue at the moment. I realize this is a report
against both an Ubuntu kernel and also an older 5.4 kernel. I have reported this
issue to Ubuntu here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2077657
however I feel like since this issue has possibly cropped up again it makes
sense to build in some protection in this path (even on the latest kernel
versions) since the code in question just blindly assumes there's a valid skb
without testing if it's NULL b/f it looks at the timestamp.
Given we have seen crashes in this path before and now this case it seems like
we should protect ourselves for when packets_out accounting is incorrect.
While we should fix that root cause we should also just make sure the skb
is not NULL before dereferencing it. Also add a warn once here to capture
some information if/when the problem case is hit again.
Fixes: e1a10ef7fa87 ("tcp: introduce tcp_rto_delta_us() helper for xmit timer fix") Signed-off-by: Josh Hunt <johunt@akamai.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rpl sr tunnel code contains calls to dst_cache_*() which are
only present when the dst cache is built.
Select DST_CACHE to build the dst cache, similar to other kconfig
options in the same file.
Compiling the rpl sr tunnel without DST_CACHE will lead to linker
errors.
Fixes: a7a29f9c361f ("net: ipv6: add rpl sr tunnel") Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the ether3_probe function, a timer is initialized with a callback
function ether3_ledoff, bound to &prev(dev)->timer. Once the timer is
started, there is a risk of a race condition if the module or device
is removed, triggering the ether3_remove function to perform cleanup.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ether3_ledoff
ether3_remove |
free_netdev(dev); |
put_devic |
kfree(dev); |
| ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
| // use dev
Fix it by ensuring that the timer is canceled before proceeding with
the cleanup in ether3_remove.
Fixes: 6fd9c53f7186 ("net: seeq: Convert timers to use timer_setup()") Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn> Link: https://patch.msgid.link/20240915144045.451-1-kxwang23@m.fudan.edu.cn Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
axienet_free_tx_chain returns the number of DMA descriptors it's
handled. However, axienet_tx_poll treats the return as the number of
packets. When scatter-gather SKBs are enabled, a single packet may use
multiple DMA descriptors, which causes incorrect packet counts. Fix this
by explicitly keepting track of the number of packets processed as
separate from the DMA descriptors.
Budget does not affect the number of Tx completions we can process for
NAPI, so we use the ring size as the limit instead of budget. As we no
longer return the number of descriptors processed to axienet_tx_poll, we
now update tx_bd_ci in axienet_free_tx_chain.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Link: https://patch.msgid.link/20240913145156.2283067-1-sean.anderson@linux.dev Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RX and TX byte/packet statistics in this driver could be overflowed
relatively quickly on a 32-bit platform. Switch these stats to use the
u64_stats infrastructure to avoid this.
This driver was using the TX IRQ handler to perform all TX completion
tasks. Under heavy TX network load, this can cause significant irqs-off
latencies (found to be in the hundreds of microseconds using ftrace).
This can cause other issues, such as overrunning serial UART FIFOs when
using high baud rates with limited UART FIFO sizes.
Switch to using a NAPI poll handler to perform the TX completion work
to get this out of hard IRQ context and avoid the IRQ latency impact.
A separate poll handler is used for TX and RX since they have separate
IRQs on this controller, so that the completion work for each of them
stays on the same CPU as the interrupt.
Testing on a Xilinx MPSoC ZU9EG platform using iperf3 from a Linux PC
through a switch at 1G link speed showed no significant change in TX or
RX throughput, with approximately 941 Mbps before and after. Hard IRQ
time in the TX throughput test was significantly reduced from 12% to
below 1% on the CPU handling TX interrupts, with total hard+soft IRQ CPU
usage dropping from about 56% down to 48%.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
The axienet_start_xmit function was updating the tx_bd_tail variable
multiple times, with potential rollbacks on error or invalid
intermediate positions, even though this variable is also used in the
TX completion path. Use READ_ONCE where this variable is read and
WRITE_ONCE where it is written to make this update more atomic, and
move the write before the MMIO write to start the transfer, so it is
protected by that implicit write barrier.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the ability to configure the RX/TX coalesce timer with ethtool.
Change default setting to scale with the clock rate rather than being a
fixed number of clock cycles.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
Now that NAPI has been implemented, the hardware interrupt mitigation
mechanism is not needed to avoid excessive interrupt load in most cases.
Reduce the default RX interrupt threshold to 1 to reduce introduced
latency. This can be increased with ethtool if desired if some applications
still want to reduce interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
Implement NAPI and GRO receive. In addition to better performance, this
also avoids handling RX packets in hard IRQ context, which reduces the
IRQ latency impact to other devices.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
When the RX or TX coalesce count is set to 1, there's no point in
setting the delay timer value since an interrupt will already be raised
on every packet, and the delay interrupt just causes extra pointless
interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
The following sequence of commands causes a livelock - there will be
workqueue process looping and consuming 100% CPU:
dmsetup create --notable test
truncate -s 1MiB testdata
losetup /dev/loop0 testdata
dmsetup load test --table '0 2048 linear /dev/loop0 0'
dd if=/dev/zero of=/dev/dm-0 bs=16k count=1 conv=fdatasync
The livelock is caused by the commit fa247089de99. The commit claims that
it fixes a race condition, however, it is unknown what the actual race
condition is and what program is involved in the race condition.
When the inactive table is loaded, the nodes /dev/dm-0 and
/sys/block/dm-0 are created. /dev/dm-0 has zero size at this point. When
the device is suspended and resumed, the nodes /dev/mapper/test and
/dev/disk/* are created.
If some program opens a block device before it is created by dmsetup or
lvm, the program is buggy, so dm could just report an error as it used to
do before.
We used to call irq_bypass_unregister_producer() in
vhost_vdpa_setup_vq_irq() which is problematic as we don't know if the
token pointer is still valid or not.
Actually, we use the eventfd_ctx as the token so the life cycle of the
token should be bound to the VHOST_SET_VRING_CALL instead of
vhost_vdpa_setup_vq_irq() which could be called by set_status().
Fixing this by setting up irq bypass producer's token when handling
VHOST_SET_VRING_CALL and un-registering the producer before calling
vhost_vring_ioctl() to prevent a possible use after free as eventfd
could have been released in vhost_vring_ioctl(). And such registering
and unregistering will only be done if DRIVER_OK is set.
Reported-by: Dragos Tatulea <dtatulea@nvidia.com> Tested-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Fixes: 2cf1ba9a4d15 ("vhost_vdpa: implement IRQ offloading in vhost_vdpa") Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240816031900.18013-1-jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This due to the fact that we do not free the "sg_table" itself while
freeing up the SG table and data pages. Fix this by freeing the sg_table
in tmc_free_sg_table().
Fixes: 99443ea19e8b ("coresight: Add generic TMC sg table framework") Cc: Mike Leach <mike.leach@linaro.org> Cc: James Clark <james.clark@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20240702132846.1677261-1-suzuki.poulose@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The binding's documentation specifies that "As the line is active low, it
should be marked GPIO_ACTIVE_LOW". However, in the driver, it was handled
the opposite way. This commit sets the driver's behaviour in sync with the
documentation
Fixes: 722407a4e8c0 ("staging:iio:ad7606: Use GPIO descriptor API") Signed-off-by: Guillaume Stols <gstols@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gpiod_set_array_value was misused here: the implementation relied on the
assumption that an unsigned long was required for each gpio, while the
function expects a bit array stored in "as much unsigned long as needed
for storing one bit per GPIO", i.e it is using a bit field.
This leaded to incorrect parameter passed to gpiod_set_array_value, that
would set 1 value instead of 3.
It also prevents to select the software mode correctly for the AD7606B.
Fixes: d2a415c86c6b ("iio: adc: ad7606: Add support for AD7606B ADC") Fixes: 41f71e5e7daf ("staging: iio: adc: ad7606: Use find_closest() macro") Signed-off-by: Guillaume Stols <gstols@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Link: https://patch.msgid.link/20240906021251.610462-1-ruanjinjie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The requested DMA channels are never released. Do this in .remove as well
as in .probe. spi_register_controller() can return -EPROBE_DEFER if
cs-gpios are not probed yet.
Do not print error messages with error code -517. Silences the following
errors upon on imx8qm:
fsl_lpspi 5a000000.spi: spi_register_controller error: -517
fsl_lpspi 5a010000.spi: spi_register_controller error: -517
fsl_lpspi 5a020000.spi: spi_register_controller error: -517
Online repaire on corrupted directory in f2fs_lookup() can generate
dirty data/meta while racing w/ readonly remount, it may leave dirty
inode after filesystem becomes readonly, however, checkpoint() will
skips flushing dirty inode in a state of readonly mode, result in
above panic.
Let's get rid of online repaire in f2fs_lookup(), and leave the work
to fsck.f2fs.
Once F2FS_IPU_FORCE policy is enabled in some cases:
a) f2fs forces to use F2FS_IPU_FORCE in a small-sized volume
b) user sets F2FS_IPU_FORCE policy via sysfs
Then we may fail to defragment file due to IPU policy check, it doesn't
make sense, let's introduce a new IPU policy to allow OPU during file
defragmentation.
In small-sized volume, let's enable F2FS_IPU_HONOR_OPU_WRITE policy
by default.
Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: 884ee6dc85b9 ("f2fs: get rid of online repaire on corrupted directory") Signed-off-by: Sasha Levin <sashal@kernel.org>
Soft IRQ Thread
- f2fs_write_end_io
- f2fs_defragment_range
- set_page_private_gcing
- type = WB_DATA_TYPE(page, false);
: assign type w/ F2FS_WB_CP_DATA
due to page_private_gcing() is true
- dec_page_count() w/ wrong type
- end_page_writeback()
Value of F2FS_WB_CP_DATA reference count may become negative under above
race condition, the root cause is we missed to wait page writeback before
setting gcing page private flag, let's fix it.
Fixes: 2d1fe8a86bf5 ("f2fs: fix to tag gcing flag on page during file defragment") Fixes: 4961acdd65c9 ("f2fs: fix to tag gcing flag on page during block migration") Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We may trigger high frequent checkpoint for below case:
1. mkdir /mnt/dir1; set dir1 encrypted
2. touch /mnt/file1; fsync /mnt/file1
3. mkdir /mnt/dir2; set dir2 encrypted
4. touch /mnt/file2; fsync /mnt/file2
...
Although, newly created dir and file are not related, due to
commit bbf156f7afa7 ("f2fs: fix lost xattrs of directories"), we will
trigger checkpoint whenever fsync() comes after a new encrypted dir
created.
In order to avoid such performance regression issue, let's record an
entry including directory's ino in global cache whenever we update
directory's xattr data, and then triggerring checkpoint() only if
xattr metadata of target file's parent was updated.
This patch updates to cover below no encryption case as well:
1) parent is checkpointed
2) set_xattr(dir) w/ new xnid
3) create(file)
4) fsync(file)
Fixes: bbf156f7afa7 ("f2fs: fix lost xattrs of directories") Reported-by: wangzijie <wangzijie1@honor.com> Reported-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Tested-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Reported-by: Yunlei He <heyunlei@hihonor.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
generic/728 - output mismatch (see /media/fstests/results//generic/728.out.bad)
--- tests/generic/728.out 2023-07-19 07:10:48.362711407 +0000
+++ /media/fstests/results//generic/728.out.bad 2023-07-19 08:39:57.000000000 +0000
QA output created by 728
+Expected ctime to change after setxattr.
+Expected ctime to change after removexattr.
Silence is golden
...
(Run 'diff -u /media/fstests/tests/generic/728.out /media/fstests/results//generic/728.out.bad' to see the entire diff)
generic/729 1s
It needs to update i_ctime after {set,remove}xattr, fix it.
When we have a corrupted main.sqlite in /var/lib/nfs/nfsdcld/, it may
result in namelen being 0, which will cause memdup_user() to return
ZERO_SIZE_PTR.
When we access the name.data that has been assigned the value of
ZERO_SIZE_PTR in nfs4_client_to_reclaim(), null pointer dereference is
triggered.
If not enough buffer space available, but idmap_lookup has triggered
lookup_fn which calls cache_get and returns successfully. Then we
missed to call cache_put here which pairs with cache_get.
Fixes: ddd1ea563672 ("nfsd4: use xdr_reserve_space in attribute encoding") Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev> Reviwed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The lookup_atid() function can return NULL if the ATID is
invalid or does not exist in the identifier table, which
could lead to dereferencing a null pointer without a
check in the `act_establish()` and `act_open_rpl()` functions.
Add a NULL check to prevent null pointer dereferencing.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
When allocating MTT hem, for each hop level of each hem that is being
allocated, the driver iterates the hem list to find out whether the
bt page has been allocated in this hop level. If not, allocate a new
one and splice it to the list. The time complexity is O(n^2) in worst
cases.
Currently the allocation for-loop uses 'unit' as the step size. This
actually has taken into account the reuse of last-hop-level MTT bt
pages by multiple buffer pages. Thus pages of last hop level will
never have been allocated, so there is no need to iterate the hem list
in last hop level.
Removing this unnecessary iteration can reduce the time complexity to
O(n).
Fixes: 38389eaa4db1 ("RDMA/hns: Add mtr support for mixed multihop addressing") Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://patch.msgid.link/20240906093444.3571619-9-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In abnormal interrupt handler, a PF reset will be triggered even if
the device is a VF. It should be a VF reset.
Fixes: 2b9acb9a97fe ("RDMA/hns: Add the process of AEQ overflow for hip08") Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://patch.msgid.link/20240906093444.3571619-7-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HNS NIC driver receives and handles the abnormal interrupt of the RAS
type generated by ROCEE, and the HNS RDMA driver does not need to handle
this type of interrupt. Therefore, delete unused codes in the HNS RDMA
driver.
Parts of the suspend and resume chain is left unprotected if we disable
the WDT here.
>From experiments we can see that the SCU disables and re-enables the WDT
when we enter and leave suspend to ram. By not touching the WDT here we
are protected by the WDT all the way to the SCU.
When ib_cache_update return an error, we exit ib_cache_setup_one
instantly with no proper cleanup, even though before this we had
already successfully done gid_table_setup_one, that results in
the kernel WARN below.
Do proper cleanup using gid_table_cleanup_one before returning
the err in order to fix the issue.
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
If we wait_for_construction and find that the file is no longer hashed,
and we're going to retry the open, the old nfsd_file reference is
currently leaked. Put the reference before retrying.
Fixes: c6593366c0bf ("nfsd: don't kill nfsd_files because of lease break error") Signed-off-by: Jeff Layton <jlayton@kernel.org> Tested-by: Youzhong Yang <youzhong@gmail.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fix leaking the of_node references in of_dra7_atl_clk_probe().
The docs for of_parse_phandle_with_args() say that the caller must call
of_node_put() on the returned node. This adds the missing of_node_put()
to fix the leak.
In the function init_conns(), after the create_con() and create_cm() for
loop if something fails. In the cleanup for loop after the destroy tag, we
access out of bound memory because cid is set to clt_path->s.con_num.
This commits resets the cid to clt_path->s.con_num - 1, to stay in bounds
in the cleanup loop later.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://patch.msgid.link/20240821112217.41827-7-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reset hb_missed_cnt after receiving traffic from other peer, so
hb is more robust again high load on host or network.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://patch.msgid.link/20240821112217.41827-5-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the commit aee2424246f9 ("RDMA/iwcm: Fix a use-after-free related to
destroying CM IDs"), the function flush_workqueue is invoked to flush the
work queue iwcm_wq.
But at that time, the work queue iwcm_wq was created via the function
alloc_ordered_workqueue without the flag WQ_MEM_RECLAIM.
Because the current process is trying to flush the whole iwcm_wq, if
iwcm_wq doesn't have the flag WQ_MEM_RECLAIM, verify that the current
process is not reclaiming memory or running on a workqueue which doesn't
have the flag WQ_MEM_RECLAIM as that can break forward-progress guarantee
leading to a deadlock.
Ensure index in rtl2830_pid_filter does not exceed 31 to prevent
out-of-bounds access.
dev->filters is a 32-bit value, so set_bit and clear_bit functions should
only operate on indices from 0 to 31. If index is 32, it will attempt to
access a non-existent 33rd bit, leading to out-of-bounds access.
Change the boundary check from index > 32 to index >= 32 to resolve this
issue.
Fixes: df70ddad81b4 ("[media] rtl2830: implement PID filter") Signed-off-by: Junlin Li <make24@iscas.ac.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure index in rtl2832_pid_filter does not exceed 31 to prevent
out-of-bounds access.
dev->filters is a 32-bit value, so set_bit and clear_bit functions should
only operate on indices from 0 to 31. If index is 32, it will attempt to
access a non-existent 33rd bit, leading to out-of-bounds access.
Change the boundary check from index > 32 to index >= 32 to resolve this
issue.
Signed-off-by: Junlin Li <make24@iscas.ac.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 4b01e01a81b6 ("[media] rtl2832: implement PID filter")
[hverkuil: added fixes tag, rtl2830_pid_filter -> rtl2832_pid_filter in logmsg] Signed-off-by: Sasha Levin <sashal@kernel.org>
For different reasons i2c transaction may fail or report id in the
message may be wrong. Avoid closing the frame in this case as it will
result in all contacts being dropped, indicating that nothing is
touching the screen anymore, while usually it is not the case.
Fixes: 42370681bd46 ("Input: Add support for ILITEK Lego Series") Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Link: https://lore.kernel.org/r/20240805085511.43955-2-francesco@dolcini.it Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to DCLK_LCDC on RK3328, the DCLK_VOP on RK3228 is typically
parented by the hdmiphy clk and it is expected that the DCLK_VOP and
hdmiphy clk rate are kept in sync.
Use CLK_SET_RATE_PARENT and CLK_SET_RATE_NO_REPARENT flags, same as used
on RK3328, to make full use of all possible supported display modes.
Fixes: 0a9d4ac08ebc ("clk: rockchip: set the clock ids for RK3228 VOP") Fixes: 307a2e9ac524 ("clk: rockchip: add clock controller for rk3228") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Link: https://lore.kernel.org/r/20240615170417.3134517-3-jonas@kwiboo.se Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize workqueue before requesting mailbox channel, otherwise if
mailbox interrupt comes before workqueue ready, the imx_rproc_rx_callback
will trigger issue.
The initialization order of SCU clocks affects the sequence of SCU clock
resume. If there are no other effects, the earlier the initialization,
the earlier the resume. During SCU clock resume, the clock rate is
restored. As SCFW guidelines, configure the parent clock rate before
configuring the child rate.
Fixes: babfaa9556d7 ("clk: imx: scu: add more scu clocks") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20240607133347.3291040-15-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The initialization order of SCU clocks affects the sequence of SCU clock
resume. If there are no other effects, the earlier the initialization,
the earlier the resume. During SCU clock resume, the clock rate is
restored. As SCFW guidelines, configure the parent clock rate before
configuring the child rate.
Fixes: 91e916771de0 ("clk: imx: scu: remove legacy scu clock binding support") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20240607133347.3291040-14-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the i.MX8M*, the TF-A exposes a SiP (Silicon Provider) service
for DDR frequency scaling. The imx8m-ddrc-devfreq driver calls the
SiP and then does clk_set_parent on the DDR muxes to synchronize
the clock tree.
since commit 936c383673b9 ("clk: imx: fix composite peripheral flags"),
these TF-A managed muxes have SET_PARENT_GATE set, which results
in imx8m-ddrc-devfreq's clk_set_parent after SiP failing with -EBUSY:
commit 926bf91248dd
("clk: imx8m: fix clock tree update of TF-A managed clocks") adds this
method and enables 8mm, 8mn and 8mq. i.MX8MP also needs it.
This is safe to do, because updating the Linux clock tree to reflect
reality will always be glitch-free.
Another reason to this patch is that powersave image BT music
requires dram to be 400MTS, so clk_set_parent(dram_alt_src,
sys1_pll_800m); is required. Without this patch, it will not succeed.
Fixes: 936c383673b9 ("clk: imx: fix composite peripheral flags") Signed-off-by: Zhipeng Wang <zhipeng.wang_1@nxp.com> Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20240607133347.3291040-7-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Switch strtoul to strtoull as an unsigned long in 32-bit build isn't
64-bits.
Fixes: c284d669a20d408b ("perf tools: Move parse_nsec_time to time-utils.c") Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com> Cc: Chaitanya S Prakash <chaitanyas.prakash@arm.com> Cc: Colin Ian King <colin.i.king@gmail.com> Cc: David Ahern <dsa@cumulusnetworks.com> Cc: Dominique Martinet <asmadeus@codewreck.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@linaro.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Garry <john.g.garry@oracle.com> Cc: Junhao He <hejunhao3@huawei.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Yang Jihong <yangjihong@bytedance.com> Link: https://lore.kernel.org/r/20240831070415.506194-3-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sched_in event for current task is not recorded, sched_in timestamp
will be set to end_time of time window interest, causing an error in
timestamp show. In this case, we choose to ignore this event.
Test scenario:
perf[1229608] does not record the first sched_in event, run time and sch delay are both 0
# perf sched timehist
Samples of sched_switch event do not have callchains.
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ ------------------------------ --------- --------- --------- 2090450.763231 [0000] perf[1229608] 0.000 0.000 0.000 2090450.763235 [0000] migration/0[15] 0.000 0.001 0.003 2090450.763263 [0001] perf[1229608] 0.000 0.000 0.000 2090450.763268 [0001] migration/1[21] 0.000 0.001 0.004 2090450.763302 [0002] perf[1229608] 0.000 0.000 0.000 2090450.763309 [0002] migration/2[27] 0.000 0.001 0.007 2090450.763338 [0003] perf[1229608] 0.000 0.000 0.000 2090450.763343 [0003] migration/3[33] 0.000 0.001 0.004
Before:
arbitrarily specify a time window of interest, timestamp will be set to an incorrect value
# perf sched timehist --time 100,200
Samples of sched_switch event do not have callchains.
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ ------------------------------ --------- --------- ---------
200.000000 [0000] perf[1229608] 0.000 0.000 0.000
200.000000 [0001] perf[1229608] 0.000 0.000 0.000
200.000000 [0002] perf[1229608] 0.000 0.000 0.000
200.000000 [0003] perf[1229608] 0.000 0.000 0.000
200.000000 [0004] perf[1229608] 0.000 0.000 0.000
200.000000 [0005] perf[1229608] 0.000 0.000 0.000
200.000000 [0006] perf[1229608] 0.000 0.000 0.000
200.000000 [0007] perf[1229608] 0.000 0.000 0.000
After:
# perf sched timehist --time 100,200
Samples of sched_switch event do not have callchains.
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ ------------------------------ --------- --------- ---------
Fixes: 853b74071110bed3 ("perf sched timehist: Add option to specify time window of interest") Signed-off-by: Yang Jihong <yangjihong@bytedance.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsa@cumulusnetworks.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20240819024720.2405244-1-yangjihong@bytedance.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When perf_time__parse_str() fails in perf_sched__timehist(),
need to free session that was previously created, fix it.
Fixes: 853b74071110bed3 ("perf sched timehist: Add option to specify time window of interest") Signed-off-by: Yang Jihong <yangjihong@bytedance.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsa@cumulusnetworks.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20240806023533.1316348-1-yangjihong@bytedance.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bpf_strtol() and bpf_strtoul() helpers are currently broken on 32bit:
The argument type ARG_PTR_TO_LONG is BPF-side "long", not kernel-side "long"
and therefore always considered fixed 64bit no matter if 64 or 32bit underlying
architecture.
This contract breaks in case of the two mentioned helpers since their BPF_CALL
definition for the helpers was added with {unsigned,}long *res. Meaning, the
transition from BPF-side "long" (BPF program) to kernel-side "long" (BPF helper)
breaks here.
Both helpers call __bpf_strtoll() with "long long" correctly, but later assigning
the result into 32-bit "*(long *)" on 32bit architectures. From a BPF program
point of view, this means upper bits will be seen as uninitialised.
Therefore, fix both BPF_CALL signatures to {s,u}64 types to fix this situation.
Now, changing also uapi/bpf.h helper documentation which generates bpf_helper_defs.h
for BPF programs is tricky: Changing signatures there to __{s,u}64 would trigger
compiler warnings (incompatible pointer types passing 'long *' to parameter of type
'__s64 *' (aka 'long long *')) for existing BPF programs.
Leaving the signatures as-is would be fine as from BPF program point of view it is
still BPF-side "long" and thus equivalent to __{s,u}64 on 64 or 32bit underlying
architectures.
Note that bpf_strtol() and bpf_strtoul() are the only helpers with this issue.
The function nilfs_btree_check_delete(), which checks whether degeneration
to direct mapping occurs before deleting a b-tree entry, causes memory
access outside the block buffer when retrieving the maximum key if the
root node has no entries.
This does not usually happen because b-tree mappings with 0 child nodes
are never created by mkfs.nilfs2 or nilfs2 itself. However, it can happen
if the b-tree root node read from a device is configured that way, so fix
this potential issue by adding a check for that case.
Due to the nature of b-trees, nilfs2 itself and admin tools such as
mkfs.nilfs2 will never create an intermediate b-tree node block with 0
child nodes, nor will they delete (key, pointer)-entries that would result
in such a state. However, it is possible that a b-tree node block is
corrupted on the backing device and is read with 0 child nodes.
Because operation is not guaranteed if the number of child nodes is 0 for
intermediate node blocks other than the root node, modify
nilfs_btree_node_broken(), which performs sanity checks when reading a
b-tree node block, so that such cases will be judged as metadata
corruption.
projects / thirdparty / kernel / stable.git / log
