Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca7e ("r8169: fix firmware not resetting tp->ocp_base") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems with memory or disk constraints often reduce the kernel footprint
by configuring LD_DEAD_CODE_DATA_ELIMINATION. However, this can result in
removal of any BTF information.
Use the KEEP() macro to preserve the BTF data as done with other important
sections, while still allowing for smaller kernels.
Fixes: 90ceddcb4950 ("bpf: Support llvm-objcopy for vmlinux BTF") Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/a635b5d3e2da044e7b51ec1315e8910fbce0083f.1600417359.git.Tony.Ambardar@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This situation was first observed with kernel 5.4.x, cross-compiled for a
MIPS target system. Fix by adding a sanity-check for export of zero-length
data sections.
Fixes: 341dfcf8d78e ("btf: expose BTF info through sysfs") Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/b38db205a66238f70823039a8c531535864eaac5.1600417359.git.Tony.Ambardar@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b0dbd97de1f1 ("platform/x86: asus-wmi: Add support for
SW_TABLET_MODE") added support for reporting SW_TABLET_MODE using the
Asus 0x00120063 WMI-device-id to see if various transformer models were
docked into their keyboard-dock (SW_TABLET_MODE=0) or if they were
being used as a tablet.
The new SW_TABLET_MODE support (naively?) assumed that non Transformer
devices would either not support the 0x00120063 WMI-device-id at all,
or would NOT set ASUS_WMI_DSTS_PRESENCE_BIT in their reply when querying
the device-id.
Unfortunately this is not true and we have received many bug reports about
this change causing the asus-wmi driver to always report SW_TABLET_MODE=1
on non Transformer devices. This causes libinput to think that these are
360 degree hinges style 2-in-1s folded into tablet-mode. Making libinput
suppress keyboard and touchpad events from the builtin keyboard and
touchpad. So effectively this causes the keyboard and touchpad to not work
on many non Transformer Asus models.
This commit fixes this by using the existing DMI based quirk mechanism in
asus-nb-wmi.c to allow using the 0x00120063 device-id for reporting
SW_TABLET_MODE on Transformer models and ignoring it on all other models.
clang static analysis flags this represenative problem
thinkpad_acpi.c:2523:7: warning: Branch condition evaluates
to a garbage value
if (!oldn->mute ||
^~~~~~~~~~~
In hotkey_kthread() mute is conditionally set by hotkey_read_nvram()
but unconditionally checked by hotkey_compare_and_issue_event().
So the tp_nvram_state variable s[2] needs to be initialized.
Fixes: 01e88f25985d ("ACPI: thinkpad-acpi: add CMOS NVRAM polling for hot keys (v9)") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: mark gross <mgross@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cfae58ed681c ("platform/x86: intel-vbtn: Only blacklist
SW_TABLET_MODE on the 9 / "Laptop" chasis-type") restored SW_TABLET_MODE
reporting on the HP stream x360 11 series on which it was previously broken
by commit de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet
mode switch on 2-in-1's").
It turns out that enabling SW_TABLET_MODE reporting on devices with a
chassis-type of 10 ("Notebook") causes SW_TABLET_MODE to always report 1
at boot on the HP Pavilion 11 x360, which causes libinput to disable the
kbd and touchpad.
The HP Pavilion 11 x360's ACPI VGBS method sets bit 4 instead of bit 6 when
NOT in tablet mode at boot. Inspecting all the DSDTs in my DSDT collection
shows only one other model, the Medion E1239T ever setting bit 4 and it
always sets this together with bit 6.
So lets treat bit 4 as a second bit which when set indicates the device not
being in tablet-mode, as we already do for bit 6.
While at it also prefix all VGBS constant defines with "VGBS_".
Fixes: cfae58ed681c ("platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mark Gross <mgross@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When devm_regulator_register() fails, ec should be
freed just like when olpc_ec_cmd() fails.
Fixes: 231c0c216172a ("Platform: OLPC: Add a regulator for the DCON") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo Handa reports that splice() can return 0 before the real EOF, if
the data in the splice source pipe is an empty pipe buffer. That empty
pipe buffer case doesn't happen in any normal situation, but you can
trigger it by doing a write to a pipe that fails due to a page fault.
Kernel threads intentionally do CLONE_FS in order to follow any changes
that 'init' does to set up the root directory (or cwd).
It is admittedly a bit odd, but it avoids the situation where 'init'
does some extensive setup to initialize the system environment, and then
we execute a usermode helper program, and it uses the original FS setup
from boot time that may be very limited and incomplete.
[ Both Al Viro and Eric Biederman point out that 'pivot_root()' will
follow the root regardless, since it fixes up other users of root (see
chroot_fs_refs() for details), but overmounting root and doing a
chroot() would not. ]
However, Vegard Nossum noticed that the CLONE_FS not only means that we
follow the root and current working directories, it also means we share
umask with whatever init changed it to. That wasn't intentional.
Just reset umask to the original default (0022) before actually starting
the usermode helper program.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The open-coded computation of the used size doesn't take the event
into account when the VIRTIO_RING_F_EVENT_IDX feature is present.
Fix that by using vhost_get_used_size().
When the IOTLB device is enabled, the vring addresses we get
from userspace are GIOVAs. It is thus wrong to pass them down
to access_ok() which only takes HVAs.
Access validation is done at prefetch time with IOTLB. Teach
vq_access_ok() about that by moving the (vq->iotlb) check
from vhost_vq_access_ok() to vq_access_ok(). This prevents
vhost_vring_set_addr() to fail when verifying the accesses.
No behavior change for vhost_vq_access_ok().
scsi_put_cdrom_generic_arg() is copying uninitialized stack memory to
userspace, since the compiler may leave a 3-byte hole in the middle of
`cgc32`. Fix it by adding a padding field to `struct
compat_cdrom_generic_command`.
Previously the code relied on device->pri to be NULL and to fail probing
later. We really should just return an error inside nvkm_device_ctor for
unsupported GPUs.
Fixes: 24d5ff40a732 ("drm/nouveau/device: rework mmio mapping code to get rid of second map") Signed-off-by: Karol Herbst <kherbst@redhat.com> Cc: dann frazier <dann.frazier@canonical.com> Cc: dri-devel <dri-devel@lists.freedesktop.org> Cc: Dave Airlie <airlied@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201006220528.13925-1-kherbst@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In nl80211_parse_key(), key.idx is first initialized as -1.
If this value of key.idx remains unmodified and gets returned, and
nl80211_key_allowed() also returns 0, then rdev_del_key() gets called
with key.idx = -1.
This causes an out-of-bounds array access.
Handle this issue by checking if the value of key.idx after
nl80211_parse_key() is called and return -EINVAL if key.idx < 0.
If exfat_read_root() returns an error, spinlock is used in
exfat_evict_inode() without initialization. This patch combines
exfat_cache_init_inode() with exfat_inode_init_once() to initialize
spinlock by slab constructor.
The AES code uses a 'br x7' as part of a function called by
a macro. That branch needs a bti_j as a target. This results
in a panic as seen below. Using x16 (or x17) with an indirect
branch keeps the target bti_c.
Bad mode in Synchronous Abort handler detected on CPU1, code 0x34000003 -- BTI
CPU: 1 PID: 265 Comm: cryptomgr_test Not tainted 5.8.11-300.fc33.aarch64 #1
pstate: 20400c05 (nzCv daif +PAN -UAO BTYPE=j-)
pc : aesbs_encrypt8+0x0/0x5f0 [aes_neon_bs]
lr : aesbs_xts_encrypt+0x48/0xe0 [aes_neon_bs]
sp : ffff80001052b730
Fixes: 0e89640b640d ("crypto: arm64 - Use modern annotations for assembly functions") Cc: <stable@vger.kernel.org> # 5.6.x- Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Suggested-by: Dave P Martin <Dave.Martin@arm.com> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20201006163326.2780619-1-jeremy.linton@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon reported an issue with the current scalar32_min_max_or() implementation.
That is, compared to the other 32 bit subreg tracking functions, the code in
scalar32_min_max_or() stands out that it's using the 64 bit registers instead
of 32 bit ones. This leads to bounds tracking issues, for example:
The bound tests on the map value force the upper unsigned bound to be 25769803777
in 64 bit (0b11000000000000000000000000000000001) and then lower one to be 1. By
using OR they are truncated and thus result in the range [1,1] for the 32 bit reg
tracker. This is incorrect given the only thing we know is that the value must be
positive and thus 2147483647 (0b1111111111111111111111111111111) at max for the
subregs. Fix it by using the {u,s}32_{min,max}_value vars instead. This also makes
sense, for example, for the case where we update dst_reg->s32_{min,max}_value in
the else branch we need to use the newly computed dst_reg->u32_{min,max}_value as
we know that these are positive. Previously, in the else branch the 64 bit values
of umin_value=1 and umax_value=32212254719 were used and latter got truncated to
be 1 as upper bound there. After the fix the subreg range is now correct:
This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:
Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425abd65b5 ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fbcon_get_font() is reading out-of-bounds. A malicious user may resize
`vc->vc_font.height` to a large value, causing fbcon_get_font() to
read out of `fontdata`.
fbcon_get_font() handles both built-in and user-provided fonts.
Fortunately, recently we have added FONT_EXTRA_WORDS support for built-in
fonts, so fix it by adding range checks using FNTSIZE().
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h", and patch "Fonts: Support FONT_EXTRA_WORDS
macros for built-in fonts".
syzbot has reported an issue in the framebuffer layer, where a malicious
user may overflow our built-in font data buffers.
In order to perform a reliable range check, subsystems need to know
`FONTDATAMAX` for each built-in font. Unfortunately, our font descriptor,
`struct console_font` does not contain `FONTDATAMAX`, and is part of the
UAPI, making it infeasible to modify it.
For user-provided fonts, the framebuffer layer resolves this issue by
reserving four extra words at the beginning of data buffers. Later,
whenever a function needs to access them, it simply uses the following
macros:
Recently we have gathered all the above macros to <linux/font.h>. Let us
do the same thing for built-in fonts, prepend four extra words (including
`FONTDATAMAX`) to their data buffers, so that subsystems can use these
macros for all fonts, no matter built-in or user-provided.
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h".
drivers/video/console/newport_con.c is borrowing FONT_EXTRA_WORDS macros
from drivers/video/fbdev/core/fbcon.h. To keep things simple, move all
definitions into <linux/font.h>.
Since newport_con now uses four extra words, initialize the fourth word in
newport_set_font() properly.
Checking for the lack of epitems refering to the epoll we want to insert into
is not enough; we might have an insertion of that epoll into another one that
has already collected the set of files to recheck for excessive reverse paths,
but hasn't gotten to creating/inserting the epitem for it.
However, any such insertion in progress can be detected - it will update the
generation count in our epoll when it's done looking through it for files
to check. That gets done under ->mtx of our epoll and that allows us to
detect that safely.
We are *not* holding epmutex here, so the generation count is not stable.
However, since both the update of ep->gen by loop check and (later)
insertion into ->f_ep_link are done with ep->mtx held, we are fine -
the sequence is
grab epmutex
bump loop_check_gen
...
grab tep->mtx // 1
tep->gen = loop_check_gen
...
drop tep->mtx // 2
...
grab tep->mtx // 3
...
insert into ->f_ep_link
...
drop tep->mtx // 4
bump loop_check_gen
drop epmutex
and if the fastpath check in another thread happens for that
eventpoll, it can come
* before (1) - in that case fastpath is just fine
* after (4) - we'll see non-empty ->f_ep_link, slow path
taken
* between (2) and (3) - loop_check_gen is stable,
with ->mtx providing barriers and we end up taking slow path.
Note that ->f_ep_link emptiness check is slightly racy - we are protected
against insertions into that list, but removals can happen right under us.
Not a problem - in the worst case we'll end up taking a slow path for
no good reason.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to call sd_zbc_init_disk() when the sdkp->zoned field is known,
that is, once sd_read_block_characteristics() is executed in
sd_revalidate_disk(), so that host-aware disks also get initialized. To do
so, move sd_zbc_init_disk() call in sd_zbc_revalidate_zones() and make sure
to execute it for all zoned disks, including for host-aware disks used as
regular disks as these disk zoned model may be changed back to BLK_ZONED_HA
when partitions are deleted.
Link: https://lore.kernel.org/r/20200915073347.832424-3-damien.lemoal@wdc.com Fixes: 5795eb443060 ("scsi: sd_zbc: emulate ZONE_APPEND commands") Cc: <stable@vger.kernel.org> # v5.8+ Reported-by: Borislav Petkov <bp@alien8.de> Tested-by: Borislav Petkov <bp@suse.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_BLK_DEV_ZONED is disabled, allow using host-aware ZBC disks as
regular disks. In this case, ensure that command completion is correctly
executed by changing sd_zbc_complete() to return good_bytes instead of 0
and causing a hang during device probe (endless retries).
When CONFIG_BLK_DEV_ZONED is enabled and a host-aware disk is detected to
have partitions, it will be used as a regular disk. In this case, make sure
to not do anything in sd_zbc_revalidate_zones() as that triggers warnings.
Since all these different cases result in subtle settings of the disk queue
zoned model, introduce the block layer helper function
blk_queue_set_zoned() to generically implement setting up the effective
zoned model according to the disk type, the presence of partitions on the
disk and CONFIG_BLK_DEV_ZONED configuration.
Link: https://lore.kernel.org/r/20200915073347.832424-2-damien.lemoal@wdc.com Fixes: b72053072c0b ("block: allow partitions on host aware zone devices") Cc: <stable@vger.kernel.org> Reported-by: Borislav Petkov <bp@alien8.de> Suggested-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current BDW virtual display port is initialized as PORT_B, so need
to use same port for VFIO EDID region, otherwise invalid EDID blob
pointer is assigned which caused kernel null pointer reference. We
might evaluate actual display hotplug for BDW to make this function
work as expected, anyway this is always required to be fixed first.
Reported-by: Alejandro Sior <aho@sior.be> Cc: Alejandro Sior <aho@sior.be> Fixes: 0178f4ce3c3b ("drm/i915/gvt: Enable vfio edid for all GVT supported platform") Reviewed-by: Hang Yuan <hang.yuan@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20200914030302.2775505-1-zhenyuw@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The introduced line event handling ABI in the commit
61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
missed the fact that 64-bit kernel may serve for 32-bit applications.
In such case the very first check in the lineevent_read() will fail
due to alignment differences.
To workaround this introduce lineevent_get_size() helper which returns actual
size of the structure in user space.
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events") Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Kent Gibson <warthog618@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") broke compilation and was temporarily fixed by Linus in 83bdc7275e62 ("random32: remove net_rand_state from the latent entropy
gcc plugin") by entirely moving net_rand_state out of the things handled
by the latent_entropy GCC plugin.
From what I understand when reading the plugin code, using the
__latent_entropy attribute on a declaration was the wrong part and
simply keeping the __latent_entropy attribute on the variable definition
was the correct fix.
The pipe splice code still used the old model of waiting for pipe IO by
using a non-specific "pipe_wait()" that waited for any pipe event to
happen, which depended on all pipe IO being entirely serialized by the
pipe lock. So by checking the state you were waiting for, and then
adding yourself to the wait queue before dropping the lock, you were
guaranteed to see all the wakeups.
Strictly speaking, the actual wakeups were not done under the lock, but
the pipe_wait() model still worked, because since the waiter held the
lock when checking whether it should sleep, it would always see the
current state, and the wakeup was always done after updating the state.
However, commit 0ddad21d3e99 ("pipe: use exclusive waits when reading or
writing") split the single wait-queue into two, and in the process also
made the "wait for event" code wait for _two_ wait queues, and that then
showed a race with the wakers that were not serialized by the pipe lock.
It's only splice that used that "pipe_wait()" model, so the problem
wasn't obvious, but Josef Bacik reports:
"I hit a hang with fstest btrfs/187, which does a btrfs send into
/dev/null. This works by creating a pipe, the write side is given to
the kernel to write into, and the read side is handed to a thread that
splices into a file, in this case /dev/null.
The box that was hung had the write side stuck here [pipe_write] and
the read side stuck here [splice_from_pipe_next -> pipe_wait].
[ more details about pipe_wait() scenario ]
The problem is we're doing the prepare_to_wait, which sets our state
each time, however we can be woken up either with reads or writes. In
the case above we race with the WRITER waking us up, and re-set our
state to INTERRUPTIBLE, and thus never break out of schedule"
Josef had a patch that avoided the issue in pipe_wait() by just making
it set the state only once, but the deeper problem is that pipe_wait()
depends on a level of synchonization by the pipe mutex that it really
shouldn't. And the whole "wait for any pipe state change" model really
isn't very good to begin with.
So rather than trying to work around things in pipe_wait(), remove that
legacy model of "wait for arbitrary pipe event" entirely, and actually
create functions that wait for the pipe actually being readable or
writable, and can do so without depending on the pipe lock serializing
everything.
Commit 387caf0b759a ("iommu/amd: Treat per-device exclusion
ranges as r/w unity-mapped regions") accidentally overwrites
the 'flags' field in IVMD (struct ivmd_header) when the I/O
virtualization memory definition is associated with the
exclusion range entry. This leads to the corrupted IVMD table
(incorrect checksum). The kdump kernel reports the invalid checksum:
ACPI BIOS Warning (bug): Incorrect checksum in table [IVRS] - 0x5C, should be 0x60 (20200717/tbprint-177)
AMD-Vi: [Firmware Bug]: IVRS invalid checksum
Fix the above-mentioned issue by modifying the 'struct unity_map_entry'
member instead of the IVMD header.
Cleanup: The *exclusion_range* functions are not used anymore, so
get rid of them.
Fixes: 387caf0b759a ("iommu/amd: Treat per-device exclusion ranges as r/w unity-mapped regions") Reported-and-tested-by: Baoquan He <bhe@redhat.com> Signed-off-by: Adrian Huang <ahuang12@lenovo.com> Cc: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20200926102602.19177-1-adrianhuang0701@gmail.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When driver has been converted to the bitmap API the non-bitmap functions
started behaving differently on 32-bit BE architectures since the bytes in
two consequent unsigned longs are in different order in comparison to byte
array. Hence if the chip had had more than 32 lines the memset() call over
it would have not set up upper lines correctly.
Although it's currently a theoretical case (no supported chips of this type
has 32+ lines), it's better to provide a clean code to avoid people thinking
this is okay and potentially producing not fully working things.
Fixes: 35d13d94893f ("gpio: pca953x: convert to use bitmap API") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Link: https://lore.kernel.org/r/20200930142013.59247-2-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
check mtk_is_virt_gpio input parameter,
virtual gpio need to support eint mode.
add error handler for the ko case
to fix this boot fail:
pc : mtk_is_virt_gpio+0x20/0x38 [pinctrl_mtk_common_v2]
lr : mtk_gpio_get_direction+0x44/0xb0 [pinctrl_paris]
Fixes: edd546465002 ("pinctrl: mediatek: avoid virtual gpio trying to set reg") Signed-off-by: Hanks Chen <hanks.chen@mediatek.com> Acked-by: Sean Wang <sean.wang@kernel.org> Singed-off-by: Jie Yang <sin_jieyang@mediatek.com> Link: https://lore.kernel.org/r/1597922546-29633-1-git-send-email-hanks.chen@mediatek.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
autofs got broken in some configurations by commit 13c164b1a186
("autofs: switch to kernel_write") because there is now an extra LSM
permission check done by security_file_permission() in rw_verify_area().
autofs is one if the few places that really does want the much more
limited __kernel_write(), because the write is an internal kernel one
that shouldn't do any user permission checks (it also doesn't need the
file_start_write/file_end_write logic, since it's just a pipe).
There are a couple of other cases like that - accounting, core dumping,
and splice - but autofs stands out because it can be built as a module.
As a result, we need to export this internal __kernel_write() function
again.
We really don't want any other module to use this, but we don't have a
"EXPORT_SYMBOL_FOR_AUTOFS_ONLY()". But we can mark it GPL-only to at
least approximate that "internal use only" for licensing.
While in this area, make autofs pass in NULL for the file position
pointer, since it's always a pipe, and we now use a NULL file pointer
for streaming file descriptors (see file_ppos() and commit 438ab720c675:
"vfs: pass ppos=NULL to .read()/.write() of FMODE_STREAM files")
This effectively reverts commits 9db977522449 ("fs: unexport
__kernel_write") and 13c164b1a186 ("autofs: switch to kernel_write").
Fixes: 13c164b1a186 ("autofs: switch to kernel_write") Reported-by: Ondrej Mosnacek <omosnace@redhat.com> Acked-by: Christoph Hellwig <hch@lst.de> Acked-by: Acked-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
the expectation is that host tools are built with debug informations.
This however doesn't happen if the Makefile assigns a new value to the
HOST_EXTRACFLAGS instead of appending to it. So use += instead of := for
the first assignment.
Fixes: e3fd9b5384f3 ("scripts/dtc: consolidate include path options in Makefile") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Blk-mq should call commit_rqs once 'bd.last != true' and no more
request will come(so virtscsi can kick the virtqueue, e.g.). We already
do that in 'blk_mq_dispatch_rq_list/blk_mq_try_issue_list_directly' while
list not empty and 'queued > 0'. However, we can seen the same scene
once the last request in list call queue_rq and return error like
BLK_STS_IOERR which will not requeue the request, and lead that list
empty but need call commit_rqs too(Or the request for virtscsi will stay
timeout until other request kick virtqueue).
We found this problem by do fsstress test with offline/online virtscsi
device repeat quickly.
Due to a HW issue, in some scenarios the LAST bit might remain set.
This will cause an unexpected NACK after reading 16 bytes on the next
read.
Example: if user tries to read from a missing device, get a NACK,
then if the next command is a long read ( > 16 bytes),
the master will stop reading after 16 bytes.
To solve this, if a command fails, check if LAST bit is still
set. If it does, reset the module.
Fixes: 56a1485b102e (i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver) Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d8d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers") Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com> Acked-by: Jochen Friedrich <jochen@scram.de> Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c3e ("gpio: aspeed: Add in ast2600 details to Aspeed driver") Signed-off-by: Tao Ren <rentao.bupt@gmail.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver") Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver") Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe738 ("gpio: pca953x: Synchronize interrupt handler properly") Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
if of_find_device_by_node() succeed, exynos_iommu_of_xlate() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: aa759fd376fb ("iommu/exynos: Add callback for initializing devices from device tree") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20200918011335.909141-1-yukuai3@huawei.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
transport_lookup_tmr_lun() uses "orig_fe_lun" member of struct se_cmd for
the lookup. Hence, update this field directly for the
TARGET_SCF_LOOKUP_LUN_FROM_TAG case.
Link: https://lore.kernel.org/r/1600300471-26135-1-git-send-email-sudhakar.panneerselvam@oracle.com Fixes: a36840d80027 ("target: Initialize LUN in transport_init_se_cmd()") Reported-by: Martin Wilck <mwilck@suse.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b571777f ("clk: exynos4: register clocks using common clock framework") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Andy reported that commit 6b41030fdc79 ("dmaengine: dmatest:
Restore default for channel") broke his scripts for the case
where "busy" channel is used for configuration with expectation
that run command would do nothing. Instead, behavior was
(unintentionally) changed to treat such case as under-configuration
and progress with defaults, i.e. run command would start a test
with default setting for channel (which would use all channels).
Restore original behavior with tracking status of channel setter
so we can distinguish between misconfigured and under-configured
cases in run command and act accordingly.
Fixes: 6b41030fdc79 ("dmaengine: dmatest: Restore default for channel") Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200922115847.30100-1-andriy.shevchenko@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit bff1cef5f23a ("clk: tegra: Don't enable already enabled PLLs")
added checks to avoid enabling PLLs that have already been enabled by
the bootloader. However, the PLL_E configuration inherited from the
bootloader isn't necessarily the one that is needed for the kernel.
This can cause SATA to fail like this:
[ 5.310270] phy phy-sata.6: phy poweron failed --> -110
[ 5.315604] tegra-ahci 70027000.sata: failed to power on AHCI controller: -110
[ 5.323022] tegra-ahci: probe of 70027000.sata failed with error -110
Fix this by always programming the PLL_E. This ensures that any mis-
configuration by the bootloader will be overwritten by the kernel.
After client is done with the COPY operation, it needs to invalidate
its pagecache (as it did no reading or writing of the data locally)
and it needs to invalidate it's attributes just like it would have
for a read on the source file and write on the destination file.
Once the linux server started giving out read delegations to
read+write opens, the destination file of the copy_file range
started having delegations and not doing syncup on close of the
file leading to xfstest failures for generic/430,431,432,433,565.
v2: changing cache_validity needs to be protected by the i_lock.
nfs_readdir_page_filler() iterates over entries in a directory, reusing
the same security label buffer, but does not reset the buffer's length.
This causes decode_attr_security_label() to return -ERANGE if an entry's
security label is longer than the previous one's. This error, in
nfs4_decode_dirent(), only gets passed up as -EAGAIN, which causes another
failed attempt to copy into the buffer. The second error is ignored and
the remaining entries do not show up in ls, specifically the getdents64()
syscall.
Reproduce by creating multiple files in NFS and giving one of the later
files a longer security label. ls will not see that file nor any that are
added afterwards, though they will exist on the backend.
In nfs_readdir_page_filler(), reset security label buffer length before
every reuse
Per the datasheet the i2c functions use MPP_Sel=0x1. They are documented
as using MPP_Sel=0x4 as well but mixing 0x1 and 0x4 is clearly wrong. On
the board tested 0x4 resulted in a non-functioning i2c bus so stick with
0x1 which works.
Fixes: d7ae8f8dee7f ("pinctrl: mvebu: pinctrl driver for 98DX3236 SoC") Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20200907211712.9697-2-chris.packham@alliedtelesis.co.nz Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb47 ("gpio: Add GPIO driver for Spreadtrum SC9860 platform") Signed-off-by: Taiping Lai <taiping.lai@unisoc.com> Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com> Reviewed-by: Baolin Wang <baolin.wang7@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Actually, the problem mentioned in scripts/link-vmlinux.sh comments;
"In theory it's possible this results in even more stubs, but unlikely"
is happening here, and ends up with another kallsyms step required.
scripts/kallsyms.c already ignores various compiler stubs. Let's do
similar to make kallsysms for PowerPC always succeed in 2 steps.
The lldd may have made calls to delete a remote port or local port and
the delete is in progress when the cli then attempts to create a new
controller. Currently, this proceeds without error although it can't be
very successful.
Fix this by validating that both the host port and remote port are
present when a new controller is to be created.
Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we use nvmeq->q_depth as the upper limit for a valid tag in
nvme_handle_cqe(), it is not correct. Because the available tag number
is recorded in tagset, which is not equal to nvmeq->q_depth.
The nvme driver registers interrupts for queues before initializing the
tagset, because it uses the number of successful request_irq() calls to
configure the tagset parameters. This allows a race condition with the
current tag validity check if the controller happens to produce an
interrupt with a corrupted CQE before the tagset is initialized.
Replace the driver's indirect tag check with the one already provided by
the block layer.
Signed-off-by: Xianting Tian <tian.xianting@h3c.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SPIE register contains counts for the TX FIFO so any time the irq
handler was invoked we would attempt to process the RX/TX fifos. Use the
SPIM value to mask the events so that we only process interrupts that
were expected.
This was a latent issue exposed by commit 3282a3da25bd ("powerpc/64:
Implement soft interrupt replay in C").
The commit eb1f00237aca ("lockdep,trace: Expose tracepoints"), started to
expose us for tracepoints. This lead to the following RCU splat on an ARM64
Qcom board.
[ 5.529634] WARNING: suspicious RCU usage
[ 5.537307] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.541092] 5.9.0-rc3 #86 Not tainted
[ 5.541098] -----------------------------
[ 5.541105] ../include/trace/events/lock.h:37 suspicious rcu_dereference_check() usage!
[ 5.541110]
[ 5.541110] other info that might help us debug this:
[ 5.541110]
[ 5.541116]
[ 5.541116] rcu_scheduler_active = 2, debug_locks = 1
[ 5.541122] RCU used illegally from extended quiescent state!
[ 5.541129] no locks held by swapper/0/0.
[ 5.541134]
[ 5.541134] stack backtrace:
[ 5.541143] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.9.0-rc3 #86
[ 5.541149] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
[ 5.541157] Call trace:
[ 5.568185] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 5.574186] dump_backtrace+0x0/0x1c8
[ 5.574206] show_stack+0x14/0x20
[ 5.574229] dump_stack+0xe8/0x154
[ 5.574250] lockdep_rcu_suspicious+0xd4/0xf8
[ 5.574269] lock_acquire+0x3f0/0x460
[ 5.574292] _raw_spin_lock_irqsave+0x80/0xb0
[ 5.574314] __pm_runtime_suspend+0x4c/0x188
[ 5.574341] psci_enter_domain_idle_state+0x40/0xa0
[ 5.574362] cpuidle_enter_state+0xc0/0x610
[ 5.646487] cpuidle_enter+0x38/0x50
[ 5.650651] call_cpuidle+0x18/0x40
[ 5.654467] do_idle+0x228/0x278
[ 5.657678] cpu_startup_entry+0x24/0x70
[ 5.661153] rest_init+0x1a4/0x278
[ 5.665061] arch_call_rest_init+0xc/0x14
[ 5.668272] start_kernel+0x508/0x540
Following the path in pm_runtime_put_sync_suspend() from
psci_enter_domain_idle_state(), it seems like we end up using the RCU.
Therefore, let's simply silence the splat by informing the RCU about it
with RCU_NONIDLE.
Note that, this is a temporary solution. Instead we should strive to avoid
using RCU_NONIDLE (and similar), but rather push rcu_idle_enter|exit()
further down, closer to the arch specific code. However, as the CPU PM
notifiers are also using the RCU, additional rework is needed.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
These will naturally fail when attempted through SQPOLL, but either
with -EFAULT or -EBADF. Make it explicit that these are not workable
through SQPOLL and return -EINVAL, just like other ops that need to
use ->files.
It would seem none of the kernel continuous integration does this:
$ cd tools/io_uring
$ make
Otherwise it may have noticed:
cc -Wall -Wextra -g -D_GNU_SOURCE -c -o io_uring-bench.o
io_uring-bench.c
io_uring-bench.c:133:12: error: static declaration of ‘gettid’
follows non-static declaration
133 | static int gettid(void)
| ^~~~~~
In file included from /usr/include/unistd.h:1170,
from io_uring-bench.c:27:
/usr/include/x86_64-linux-gnu/bits/unistd_ext.h:34:16: note:
previous declaration of ‘gettid’ was here
34 | extern __pid_t gettid (void) __THROW;
| ^~~~~~
make: *** [<builtin>: io_uring-bench.o] Error 1
The problem on Ubuntu 20.04 (with lk 5.9.0-rc5) is that unistd.h
already defines gettid(). So prefix the local definition with
"lk_".
For 64bit CONFIG_BASE_SMALL=0 systems PID_MAX_LIMIT is set by default to 4194304. During boot the kernel sets a new value based on number of CPUs
but no lower than 32768. It is 1024 per CPU so with 128 CPUs the default
becomes 131072 which needs six digits.
This value can be increased during run time but must not exceed the
initial upper limit.
Systemd sometime after v241 sets it to the upper limit during boot. The
result is that when the pid exceeds five digits, the trace output is a
little hard to read because it is no longer properly padded (same like
on big iron with 98+ CPUs).
Radiotap header field 'Channel flags' has '2 GHz spectrum' set to
'true' for 6GHz packet.
Change it to 5GHz as there isn't a separate option available for 6GHz.
This patch sets skb->protocol before transmitting frames on the HDLC
device, so that a user listening on the HDLC device with an AF_PACKET
socket will see outgoing frames' sll_protocol field correctly set and
consistent with that of incoming frames.
1. Control frames in hdlc_cisco and hdlc_ppp
When these drivers send control frames, skb->protocol is not set.
This value should be set to htons(ETH_P_HDLC), because when receiving
control frames, their skb->protocol is set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, which then calls
cisco_type_trans or ppp_type_trans. The skb->protocol of control frames
is set to htons(ETH_P_HDLC) so that the control frames can be received
by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the
control frames.
2. hdlc_fr
When this driver sends control frames, skb->protocol is set to internal
values used in this driver.
When this driver sends data frames (from upper stacked PVC devices),
skb->protocol is the same as that of the user data packet being sent on
the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3)
(for Ethernet-emulating PVC devices).
However, skb->protocol for both control frames and data frames should be
set to htons(ETH_P_HDLC), because when receiving, all frames received on
the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, and because this
driver doesn't provide a type_trans function in struct hdlc_proto,
all frames will have their skb->protocol set to htons(ETH_P_HDLC).
The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx
to process the frames (control frames are consumed and data frames
are re-received on upper PVC devices).
Cc: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver is a virtual driver stacked on top of Ethernet interfaces.
When this driver transmits data on the Ethernet device, the skb->protocol
setting is inconsistent with the Ethernet header prepended to the skb.
This causes a user listening on the Ethernet interface with an AF_PACKET
socket, to see different sll_protocol values for incoming and outgoing
frames, because incoming frames would have this value set by parsing the
Ethernet header.
This patch changes the skb->protocol value for outgoing Ethernet frames,
making it consistent with the Ethernet header prepended. This makes a
user listening on the Ethernet device with an AF_PACKET socket, to see
the same sll_protocol value for incoming and outgoing frames.
Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Get and put the reference to the ctrl in the nvme_dev_open() and
nvme_dev_release() before and after module get/put for ctrl in char
device file operations.
Introduce char_dev relase function, get/put the controller and module
which allows us to fix the potential Oops which can be easily reproduced
with a passthru ctrl (although the problem also exists with pure user
access):
Reported-by: Eric Sandeen <esandeen@redhat.com> Signed-off-by: David Milburn <dmilburn@redhat.com> Tested-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Increase Rx ring size to address issue where hardware is reaching
the receive work limit.
Before:
[ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached
Signed-off-by: Lucy Yan <lucyyan@google.com> Reviewed-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous change "hv_netvsc: Switch the data path at the right time
during hibernation" adds the call of netvsc_vf_changed() upon
NETDEV_CHANGE, so it's necessary to avoid the duplicate call and message
when the VF is brought UP or DOWN.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch causes a regression betwen Kernel 5.7 and 5.8 at wlcore:
with it applied, WiFi stops working, and the Kernel starts printing
this message every second:
PVC devices are virtual devices in this driver stacked on top of the
actual HDLC device. They are the devices normal users would use.
PVC devices have two types: normal PVC devices and Ethernet-emulating
PVC devices.
When transmitting data with PVC devices, the ndo_start_xmit function
will prepend a header of 4 or 10 bytes. Currently this driver requests
this headroom to be reserved for normal PVC devices by setting their
hard_header_len to 10. However, this does not work when these devices
are used with AF_PACKET/RAW sockets. Also, this driver does not request
this headroom for Ethernet-emulating PVC devices (but deals with this
problem by reallocating the skb when needed, which is not optimal).
This patch replaces hard_header_len with needed_headroom, and set
needed_headroom for Ethernet-emulating PVC devices, too. This makes
the driver to request headroom for all PVC devices in all cases.
Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ubuntu mainline builds for ppc64le are failing with the below error (*):
CALL /home/kernel/COD/linux/scripts/atomic/check-atomics.sh
DESCEND bpf/resolve_btfids
resolve_btfids needs to be build as a host binary and it needs libbpf.
However, libbpf Makefile hardcodes an include path utilizing $(ARCH).
This results in mixing of cross-architecture headers resulting in a
build failure.
The specific header include path doesn't seem necessary for a libbpf
build. Hence, remove the same.
Using dev_kfree_skb for tx skbs breaks AQL. This worked until now only
by accident, because a mac80211 issue breaks AQL on drivers with firmware
rate control that report the rate via ieee80211_tx_status_ext as struct
rate_info.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200812144943.91974-1-nbd@nbd.name Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the check for the mainline vboxsf code being used with the old
mount.vboxsf mount binary from the out-of-tree vboxsf version doing
a comparison between signed and unsigned data types.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the timer counts to the upper limit, an overflow interrupt is
generated, and the count is reset with the value in the TIME_INI
register. But the software expects to start counting from 0 when
the count overflows, so it forces TIME_INI to 0 to solve the
potential interrupt storm problem.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com> Tested-by: Xu Kai <xukai@nationalchip.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/1597735877-71115-1-git-send-email-guoren@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit c330fb1ddc0a ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.")
Xen is using the chip_data pointer for storing IRQ specific data. When
running as a HVM domain this can result in problems for legacy IRQs, as
those might use chip_data for their own purposes.
Use a local array for this purpose in case of legacy IRQs, avoiding the
double use.
Cc: stable@vger.kernel.org Fixes: c330fb1ddc0a ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.") Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Stefan Bader <stefan.bader@canonical.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20200930091614.13660-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent attempt to fix a ref count leak in
amdgpu_display_crtc_set_config() turned out to be doing too much and
"fixed" an intended decrease as if it were a leak. Undo that part to
restore the proper balance. This is the very nature of this function
to increase or decrease the power reference count depending on the
situation.
Consequences of this bug is that the power reference would
eventually get down to 0 while the display was still in use,
resulting in that display switching off unexpectedly.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: e008fa6fb415 ("drm/amdgpu: fix ref count leak in amdgpu_display_crtc_set_config") Cc: stable@vger.kernel.org Cc: Navid Emamdoost <navid.emamdoost@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 6827ca573c03 ("memstick: rtsx_usb_ms: Support runtime power
management"), removing module rtsx_usb_ms will be stuck.
The deadlock is caused by powering on and powering off at the same time,
the former one is when memstick_check() is flushed, and the later is called
by memstick_remove_host().
Soe let's skip allocating card to prevent this issue.
The temp buffer size variable for trace_find_next_entry() was incorrectly
being updated when the size did not change. The temp buffer size should only
be updated when it is reallocated.
This is mostly an issue when used with ftrace_dump(). That's because
ftrace_dump() can not allocate a new buffer, and instead uses a temporary
buffer with a fix size. But the variable that keeps track of that size is
incorrectly updated with each call, and it could fall into the path that
would try to reallocate the buffer and produce a warning.
Not only fix the updating of the temp buffer, but also do not free the temp
buffer before a new buffer is allocated (there's no reason to not continue
to use the current temp buffer if an allocation fails).
Cc: stable@vger.kernel.org Fixes: 8e99cf91b99bb ("tracing: Do not allocate buffer in trace_find_next_entry() in atomic") Reported-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first thing that the ftrace function callback helper functions should do
is to check for recursion. Peter Zijlstra found that when
"rcu_is_watching()" had its notrace removed, it caused perf function tracing
to crash. This is because the call of rcu_is_watching() is tested before
function recursion is checked and and if it is traced, it will cause an
infinite recursion loop.
rcu_is_watching() should still stay notrace, but to prevent this should
never had crashed in the first place. The recursion prevention must be the
first thing done in callback functions.
Link: https://lore.kernel.org/r/20200929112541.GM2628@hirez.programming.kicks-ass.net Cc: stable@vger.kernel.org Cc: Paul McKenney <paulmck@kernel.org> Fixes: c68c0fa293417 ("ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too") Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, PCI drivers with runtime PM enabled will skip the calls
to suspend and resume on system PM. For this driver, we don't want
that, as we need to perform additional steps for system PM to work
properly on all systems. So instruct the PM core to not skip these
calls.
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM") Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com> Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel may fail to boot or devices may fail to come up when
initializing iscsi_tcp devices starting with Linux 5.8.
Commit a79af8a64d39 ("[SCSI] iscsi_tcp: use iscsi_conn_get_addr_param
libiscsi function") introduced getpeername() within the session spinlock.
Commit 1b66d253610c ("bpf: Add get{peer, sock}name attach types for
sock_addr") introduced BPF_CGROUP_RUN_SA_PROG_LOCK() within getpeername(),
which acquires a mutex and when used from iscsi_tcp devices can now lead to
"BUG: scheduling while atomic:" and subsequent damage.
Ensure that the spinlock is released before calling getpeername() or
getsockname(). sock_hold() and sock_put() are used to ensure that the
socket reference is preserved until after the getpeername() or
getsockname() complete.
BPLL clock must not be disabled because it is needed for proper DRAM
operation. This is normally handled by respective memory devfreq driver,
but when that driver is not yet probed or its probe has been deferred
the clock might get disabled what causes board hang. Fix this by calling
clk_prepare_enable() directly from the clock provider driver.
Cc: stable@vger.kernel.org Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Tested-by: Lukasz Luba <lukasz.luba@arm.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20200807133143.22748-1-m.szyprowski@samsung.com Fixes: 6e7674c3c6df ("memory: Add DMC driver for Exynos5422") Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original commit appears to have the logic reversed in
amd_fch_gpio_get_direction. Also confirmed by observing the value of
"direction" in the sys tree.
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
projects / thirdparty / kernel / stable.git / log
