Voicemail transfer to operator should occur immediately, not after main menu.
There were two scenarios in the advanced options that while using the
operator=yes and review=yes options, the transfer occurred only after exiting
the main menu (after sending a reply or leaving a message for an extension).
Now after the audio is processed for the reply or message the transfer occurs
immediately as expected.
Ensure channel state is not incorrectly set in the case of a very early answer.
The needringing bit was being read in dahdi_read after answering thereby
setting the state to ringing from up. This clears needringing upon answering
so that is no longer possible.
Fix potential crash from race condition due to accessing channel data without the channel locked.
In res_musiconhold.c, there are several places where a channel's
stream's existence is checked prior to calling ast_closestream on it. The issue
here is that in several cases, the channel was not locked while checking the
stream. The result was that if two threads checked the state of the channel's
stream at approximately the same time, then there could be a situation where
both threads attempt to call ast_closestream on the channel's stream. The result
here is that the refcount for the stream would go below 0, resulting in a crash.
I have added proper channel locking to res_musiconhold.c to ensure that
we do not try to check chan->stream without the channel locked. A Digium customer
has been using this patch for several weeks and has not had any crashes since
applying the patch.
The code handling DTMF CallerID drops digits on long CallerID numbers and
may timeout waiting for the first ring with shorter numbers.
The DTMF emulation mode was not turned off when processing DTMF CallerID.
When the emulation code gets behind in processing the DTMF digits it can
skip a digit.
For shorter numbers, the timeout may have been too short. I increased it
from 2 seconds to 4 seconds. Four seconds is a typical time between rings
for many countries.
(closes issue #16460)
Reported by: sum
Patches:
issue16460.patch uploaded by rmudgett (license 664)
issue16460_v1.6.2.patch uploaded by rmudgett (license 664)
Tested by: sum, rmudgett
The middle_frame in the audiohook_write_list function was
being freed if a audiohook manipulator returned a failure.
This is incorrect logic. This patch resolves this and
adds detailed descriptions of how this function should work
and why manipulator failures must be ignored.
Issue_1.
In the local_hangup() 3 locks must be held at the same time... pvt, pvt->chan,
and pvt->owner. Proper deadlock avoidance is done when the channel to hangup
is the outbound chan_local channel, but when it is not the outbound channel we
have an issue... We attempt to do deadlock avoidance only on the tech pvt, when
both the tech pvt and the pvt->owner are locked coming into that loop. By
never giving up the pvt->owner channel deadlock avoidance is not entirely possible.
This patch resolves that by doing deadlock avoidance on both the pvt->owner and the pvt
when trying to get the pvt->chan lock.
Issue_2.
ast_prod() is used in ast_activate_generator() to queue a frame on the channel
and make the channel's read function get called. This function is used in
ast_activate_generator() while the channel is locked, which mean's the channel
will have a lock both from the generator code and the frame_queue code by the
time it gets to chan_local.c's local_queue_frame code... local_queue_frame
contains some of the same crazy deadlock avoidance that local_hangup requires,
and this recursive lock prevents that deadlock avoidance from happening correctly.
This patch removes ast_prod() from the channel lock so only one lock is held during
the local_queue_frame function.
Updating config.guess because after installing Ubuntu Server 9.10 and
running all the update scripts, running ./configure would not continue
because it was unable to determine what kind of system I had. After
updating config.guess things started working again.
........
................
Remove usage of `id` since it isn't useful and was causing breakge.
Solaris `id` doesn't support the -u argument. Instead of figuring out how to
fix this to work on Solaris, I decided to check why it was necessary and where
else it was used. It was only used in one place, and it hasn't been needed
for a very long time (I question whether it was ever needed).
........
................
Changed the warning to "Failed to decode CallerID on channel 'name'". The
message before it is likely more specific about why the CallerID decode
failed.
* Add additional sounds prompts for say_enumeration
* Update the English conference sounds prompts so they are better
quality and all sound more consistent
* Clean up the core-sounds-XX.txt and extra-sounds-XX.txt files to
include all present sound files
Both core (en, fr, es) and extra (en, fr) sounds files have been updated.
Add gar to the check for AR for those silly OSes (Solaris) that don't have ar.
autoconf2.13 couldn't handle AC_PROG_GREP, so I removed it. This is fine,
since we don't need to use anything that the configure script doesn't.
........
Support the silly OSes that don't have ar and strip.
Since AC_PATH_TOOL is equiv to AC_CHECK_TOOL when path isn't specified, and
AC_PATH_TOOLS doesn't exist, we'll just switch to AC_CHECK_TOOLS.
........
................
Issue #7321 implements a new chan_dahdi configuration option. However, a
change mentioned in the issue was never implemented. This is the change
that will allow the feature to work.
I added a note to chan_dahdi.conf.sample about the feature.
Prevent Newchannel manager events for dummy channels.
No Newchannel manager event will be fired for channels that are
allocated to not match a registered technology type. Thus bogus
channels allocated solely for variable substitution or CDR
operations do not result in a Newchannel event.
When StopMonitor is called, ensure that it will not be restarted by a channel event.
(closes issue #16590)
Reported by: kkm
Patches:
resmonitor-16590-trunk.239289.diff uploaded by kkm (license 888)
........
................
This change allows a CDR record previously marked with disposition ANSWERED to be set as BUSY or NO ANSWER.
Additionally this change partially reverts r235635 and does not set the AST_CDR_FLAG_ORIGINATED flag on CDRs generated from ast_call(). To preserve proper CDR behavior, the AST_CDR_FLAG_DIALED flag is now cleared from all brige CDRs in ast_bridge_call().
Fix looping forever when no input received in certain voicemail menu scenarios.
Specifically, prompting for an extension (when leaving or forwarding a message)
or when prompting for a digit (when saving a message or changing folders).
Play correct prompt when voicemail store failure occurs after attempted forward.
If a user's mailbox was full and a message was attempted to be forwarded to
said box, warnings on the console would indicate failure. However, the played
prompt was that of success (vm-msgsaved). Now storage failure is taken into
account and the correct prompt (vm-mailboxfull) is played when appropriate.
Make the mixmonitor thread process audio frames faster
Mantis issue 17078 reports MixMonitor recordings have shorter durations than
the call duration. This was because the mixmonitor thread was not processing
frames from the audiohook fast enough. The mixmonitor thread would slowly fall
behind the most recent audio frame and when the channel hangs up, the mixmonitor
thread would exit without processing the same number of frames as the channel;
leaving the mixmonitor recording shorter than actual call duration.
This revision fixes this issue by moving the ast_audiohook_trigger_wait() and
the subsequent audiohook.status check into the block where the
ast_audiohook_read_frame() function returns NULL.
Enable PRI SERVICE message support in chan_dahdi for the 'national' switchtype
Revision 1072 of libpri added SERVICE message support for the 'national'
switchtype. The attached patch enables the use of 'pri service' CLI commands
on dahdi channels that are configured for the 'national' switchtype.
Don't recreate peer, when responding to a repeated deregistration attempt.
When a reply to a deregistration is lost in transmit, the client retries the
deregistration. Previously, this would cause a realtime/autocreate peer to be
loaded back into memory, after it had already been correctly purged. Instead,
we just want to resend the reply without loading the peer.
Update the backtrace.txt documentation so it conforms to the same layout as
other documents we've been working on recently. Additionally, add a bunch of
new information about gathering backtraces for crashes and deadlocks, along
with ways of verifying your file before uploading it. Create a couple of one
line commands for people to generate the files we need.
Yet another issue where the conversion of the application delimiter to comma caused an issue.
Application arguments within the feature map could possibly contain a comma,
which conflicts with the syntax of the features.conf configuration file. This
patch allows the argument to be wrapped in parentheses or quoted, to allow the
application arguments to be interpreted as a single configuration parameter.
Add an option to restore past broken behavor of the Events manager action
Before r238915, certain values for the EventMask parameter of the Events action would result in no response being returned. This patch adds an option to restore that broken behavior. Also while fixing this bug I discovered that passing an empty EventMasks parameter would also result in no response being returned, this has been fixed as well while being preserved when the broken behavior is requested.
Add How-To document on collecting debugging info for issues.asterisk.org
Paul Belanger has been helping a lot with bug tracking recently and created
this document that we can now point to when additional debugging information
is required. This document will help those filing issues to know how to get
the information required when filing their issues. This will make things
easier on the developers.
Initial text and changes by pabelanger. Tweaks and editing by myself.
Mark Michelson [Thu, 25 Mar 2010 17:05:40 +0000 (17:05 +0000)]
Fix crashes resulting from reading non-existent RTP streams.
Specifically, when using the CHANNEL dialplan function, it was
possible to crash Asterisk by trying to get the rtpdest of a
stream type that is not in use by the channel. This commit
fixes that issue.
Leif Madsen [Thu, 25 Mar 2010 17:02:17 +0000 (17:02 +0000)]
Make safe_asterisk work on dash/sh/bash etc.
Merged from the change to trunk via issue #13111. For some reason
the changes there were only done on trunk, and thus were available
for 1.6.1 and 1.6.2 when they were branched. Because this change is
available on both 1.6.1 and 1.6.2, it makes sense to allow it on the
1.6.0 branch as well.
(closes issue #17094)
Reported by: stuarth
Much thanks to Tilghman and Sean Bright for the help on this merge.
Merged revisions 135061 via svnmerge from
https://origsvn.digium.com/svn/asterisk/trunk
Here is a copy and paste of the details from my request on
reviewboard that dealt with these changes:
Fix 1. The first change in place is to fix Mantis issue 15811, which deals with a situation where Asterisk will incorrectly interpret out of order RFC2833 frames as duplicate DTMF digits. For instance, we would receive a sequence like:
Prior to this patch when we received the frame with seqno 5, we would interpret this as a new DTMF 1. With this patch, we will check the seqno of the incoming digit and not process the frame if the seqno is lower than the last recorded seqno. Note that we do not record the seqno of the dropped DTMF frame for future processing. While the above situation is what was designed to be fixed, the patch is written in such a way that the following would also be fixed too:
In this second situation, the beginning of the DTMF 2 arrives before the final end frame of the DTMF 1. With the patch, seqno 12 is no processed and thus we properly interpret the DTMF.
Fix 2. The second change in place is to fix an issue like the following:
When we receive seqno 6, we had code in place that was supposed to properly end the previously unended DTMF 1. The problem was that the code was essentially a no-op. The code would set up an end frame for the DTMF 1 but would immediately overwrite the frame with the begin for DTMF 2. I changed process_dtmf_rfc2833() so that instead of returning a single frame, it is given as an output parameter a list of frames. Each frame that needs to be returned is appended to this list.
Fix 3. The final change is a minor one where an AST_CONTROL_SRCCHANGE frame could get lost. If we process a cisco DTMF or an RFC 3389 frame and no frame was returned, then we would return &ast_null_frame. The problem is that earlier in the function, we may have generated an AST_CONTROL_SRCCHANGE frame and put it in the list of frames we wish to return. This frame would be lost in such a case. The patch fixes this problem
........
................
Ensure that monitor recordings are written to the correct location (again)
This is an extension to 248860. As such the dialplan test has been extended:
; non absolute path, not combined
exten => 5040, 1, monitor(wav,tmp/jeff/monitor_test)
exten => 5040, n, dial(sip/5001)
; absolute path, not combined
exten => 5041, 1, monitor(wav,/tmp/jeff/monitor_test2)
exten => 5041, n, dial(sip/5001)
; no path, not combined
exten => 5042, 1, monitor(wav,monitor_test3)
exten => 5042, n, dial(sip/5001)
; combined: changemonitor from non absolute to no path (leaves tmp/jeff)
exten => 5043, 1, monitor(wav,tmp/jeff/monitor_test4,m)
exten => 5043, n, changemonitor(monitor_test5)
exten => 5043, n, dial(sip/5001)
; combined: changemonitor from no path to non absolute path
exten => 5044, 1, monitor(wav,monitor_test6,m)
exten => 5044, n, changemonitor(tmp/jeff/monitor_test7) ; this wasn't possible before
exten => 5044, n, dial(sip/5001)
; non absolute path, combined
exten => 5045, 1, monitor(wav,tmp/jeff/monitor_test8,m)
exten => 5045, n, dial(sip/5001)
; absolute path, combined
exten => 5046, 1, monitor(wav,/tmp/jeff/monitor_test9,m)
exten => 5046, n, dial(sip/5001)
; no path, combined
exten => 5047, 1, monitor(wav,monitor_test10,m)
exten => 5047, n, dial(sip/5001)
; combined: changemonitor from non absolute to absolute (leaves tmp/jeff)
exten => 5048, 1, monitor(wav,tmp/jeff/monitor_test11,m)
exten => 5048, n, changemonitor(/tmp/jeff/monitor_test12)
exten => 5048, n, dial(sip/5001)
; combined: changemonitor from absolute to non absolute (leaves /tmp/jeff)
exten => 5049, 1, monitor(wav,/tmp/jeff/monitor_test13,m)
exten => 5049, n, changemonitor(tmp/jeff/monitor_test14)
exten => 5049, n, dial(sip/5001)
; combined: changemonitor from no path to absolute
exten => 5050, 1, monitor(wav,monitor_test15,m)
exten => 5050, n, changemonitor(/tmp/jeff/monitor_test16)
exten => 5050, n, dial(sip/5001)
; combined: changemonitor from absolute to no path (leaves /tmp/jeff)
exten => 5051, 1, monitor(wav,/tmp/jeff/monitor_test17,m)
exten => 5051, n, changemonitor(monitor_test18)
exten => 5051, n, dial(sip/5001)
; not combined: changemonitor from non absolute to no path (leaves tmp/jeff)
exten => 5052, 1, monitor(wav,tmp/jeff/monitor_test19)
exten => 5052, n, changemonitor(monitor_test20)
exten => 5052, n, dial(sip/5001)
; not combined: changemonitor from no path to non absolute
exten => 5053, 1, monitor(wav,monitor_test21)
exten => 5053, n, changemonitor(tmp/jeff/monitor_test22)
exten => 5053, n, dial(sip/5001)
; not combined: changemonitor from non absolute to absolute (leaves tmp/jeff)
exten => 5054, 1, monitor(wav,tmp/jeff/monitor_test23)
exten => 5054, n, changemonitor(/tmp/jeff/monitor_test24)
exten => 5054, n, dial(sip/5001)
; not combined: changemonitor from absolute to non absolute (leaves /tmp/jeff)
exten => 5055, 1, monitor(wav,/tmp/jeff/monitor_test24)
exten => 5055, n, changemonitor(tmp/jeff/monitor_test25)
exten => 5055, n, dial(sip/5001)
; not combined: changemonitor from no path to absolute
exten => 5056, 1, monitor(wav,monitor_test26)
exten => 5056, n, changemonitor(/tmp/jeff/monitor_test27)
exten => 5056, n, dial(sip/5001)
; not combined: changemonitor from absolute to no path (leaves /tmp/jeff)
exten => 5057, 1, monitor(wav,/tmp/jeff/monitor_test28)
exten => 5057, n, changemonitor(monitor_test29)
exten => 5057, n, dial(sip/5001)
........
................
Exit native bridging early for greater timing accuracy with warnings
This changes native bridging to break one millisecond early so that the more
accurate timeval calculations done in the generic bridge can be performed using
the bridge config. Currently the time between exiting native bridging slightly
late can sometimes cause a large enough discrepancy for warnings to be missed.
For the record, 1.4 does not attempt to native bridge at all when warnings are
enabled.
Mask out previous arguments on each nested invocation of Gosub.
(closes issue #16758)
Reported by: wdoekes
Patches:
20100316__issue16758.diff.txt uploaded by tilghman (license 14)
Russell Bryant [Tue, 16 Mar 2010 19:01:27 +0000 (19:01 +0000)]
Merged revisions 252767 via svnmerge from
https://origsvn.digium.com/svn/asterisk/trunk
................
r252767 | russell | 2010-03-16 14:01:04 -0500 (Tue, 16 Mar 2010) | 13 lines
Merged revisions 252766 via svnmerge from
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r252766 | russell | 2010-03-16 14:00:43 -0500 (Tue, 16 Mar 2010) | 6 lines
Don't treat warnings as errors for muted.
muted supports OS X, but uses functions marked as deprecated in 10.6. However,
the functions are still supported, so just ignore the warnings for now and
allow the build to proceed.
........
................
Fixing up a couple more overlapping global variable namespaces shared with
extensions.conf.sample. Also noticed a few of the lines that were commented
out didn't have the closing semi-colon so I added that as well.
Update extensions.ael file to not overlap extensions.conf.
Updated the extensions.ael file so the global variables don't overlap
those that we have in extensions.conf (sample files). This way unexpected
things won't happed hopefully if both pbx_ael and res_config are loaded.
Only change the RTP ssrc when we see that it has changed
This change basically reverts the change reviewed in
https://reviewboard.asterisk.org/r/374/ and instead limits the
updating of the RTP synchronization source to only those times when we
detect that the other side of the conversation has changed the ssrc.
The problem is that SRCUPDATE control frames are sent many times where
we don't want a new ssrc, including whenever Asterisk has to send DTMF
in a normal bridge. This is also not the first time that this mistake
has been made. The initial implementation of the ast_rtp_new_source
function also changed the ssrc--and then it was removed because of
this same issue. Then, we put it back in again to fix a different
issue. This patch attempts to only change the ssrc when we see that
the other side of the conversation has changed the ssrc.
It also renames some functions to make their purpose more clear.
Fix ParkAndAnnounce not respecting parking options.
The patch ensures that if a peer does not exist, parking settings are read from
the channel. A unit test has been written to ensure proper operation for both
standard parking and parking using masquerades.
Fix Debian init script to not use -c.
When using the init script as-is currently, it could cause issues on Debian
such as high CPU usage. This fix has worked for several people so I'm
implementing the change.
A complete re-write of the Local channel documentation has been performed, with
the existing information from localchannel.txt and localchannel.tex merged in.
projects / thirdparty / asterisk.git / log
