Current code produces a warning as shown below when total characters
in the constituent block device names plus the slashes exceeds 200.
snprintf() returns the number of characters generated from the given
input, which could cause the expression “200 – len” to wrap around
to a large positive number. Fix this by using scnprintf() instead,
which returns the actual number of characters written into the buffer.
The meson_nfc_ecc_correct() function accidentally does a right shift
instead of a left shift so it only works for BIT(0). Also use
BIT_ULL() because "correct_bitmap" is a u64 and we want to avoid
shift wrapping bugs.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Liang Yang <liang.yang@amlogic.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/YuI2zF1hP65+LE7r@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
ACS-5 section
7.13.6.36 Word 78: Serial ATA features supported
states that:
If word 76 is not 0000h or FFFFh, word 78 reports the features supported
by the device. If this word is not supported, the word shall be cleared
to zero.
(This text also exists in really old ACS standards, e.g. ACS-3.)
The problem with ata_id_has_dipm() is that the while it performs a
check against 0 and 0xffff, it performs the check against
ATA_ID_FEATURE_SUPP (word 78), the same word where the feature bit
is stored.
Fix this by performing the check against ATA_ID_SATA_CAPABILITY
(word 76), like required by the spec. The feature bit check itself
is of course still performed against ATA_ID_FEATURE_SUPP (word 78).
Additionally, move the macro to the other ATA_ID_FEATURE_SUPP macros
(which already have this check), thus making it more likely that the
next ATA_ID_FEATURE_SUPP macro that is added will include this check.
Fixes: ca77329fb713 ("[libata] Link power management infrastructure") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ACS-5 section
7.13.6.36 Word 78: Serial ATA features supported
states that:
If word 76 is not 0000h or FFFFh, word 78 reports the features supported
by the device. If this word is not supported, the word shall be cleared
to zero.
(This text also exists in really old ACS standards, e.g. ACS-3.)
Additionally, move the macro to the other ATA_ID_FEATURE_SUPP macros
(which already have this check), thus making it more likely that the
next ATA_ID_FEATURE_SUPP macro that is added will include this check.
Fixes: 5b01e4b9efa0 ("libata: Implement NCQ autosense") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ACS-5 section
7.13.6.36 Word 78: Serial ATA features supported
states that:
If word 76 is not 0000h or FFFFh, word 78 reports the features supported
by the device. If this word is not supported, the word shall be cleared
to zero.
(This text also exists in really old ACS standards, e.g. ACS-3.)
Additionally, move the macro to the other ATA_ID_FEATURE_SUPP macros
(which already have this check), thus making it more likely that the
next ATA_ID_FEATURE_SUPP macro that is added will include this check.
Fixes: 65fe1f0f66a5 ("ahci: implement aggressive SATA device sleep support") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ACS-5 section
7.13.6.41 Words 85..87, 120: Commands and feature sets supported or enabled
states that:
If bit 15 of word 86 is set to one, bit 14 of word 119 is set to one,
and bit 15 of word 119 is cleared to zero, then word 119 is valid.
If bit 15 of word 86 is set to one, bit 14 of word 120 is set to one,
and bit 15 of word 120 is cleared to zero, then word 120 is valid.
(This text also exists in really old ACS standards, e.g. ACS-3.)
Currently, ata_id_sense_reporting_enabled() and
ata_id_has_sense_reporting() both check bit 15 of word 86,
but neither of them check that bit 14 of word 119 is set to one,
or that bit 15 of word 119 is cleared to zero.
Additionally, make ata_id_sense_reporting_enabled() return false
if !ata_id_has_sense_reporting(), similar to how e.g.
ata_id_flush_ext_enabled() returns false if !ata_id_has_flush_ext().
Fixes: e87fd28cf9a2 ("libata: Implement support for sense data reporting") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Delay QP destroy completion until all siw references to QP are
dropped. The calling RDMA core will free QP structure after
successful return from siw_qp_destroy() call, so siw must not
hold any remaining reference to the QP upon return.
A use-after-free was encountered in xfstest generic/460, while
testing NFSoRDMA. Here, after a TCP connection drop by peer,
the triggered siw_cm_work_handler got delayed until after
QP destroy call, referencing a QP which has already freed.
Fixes: 303ae1cdfdf7 ("rdma/siw: application interface") Reported-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Link: https://lore.kernel.org/r/20220920082503.224189-1-bmt@zurich.ibm.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For header and trailer/padding processing, siw did not consume new
skb data until minimum amount present to fill current header or trailer
structure, including potential payload padding. Not consuming any
data during upcall may cause a receive stall, since tcp_read_sock()
is not upcalling again if no new data arrive.
A NFSoRDMA client got stuck at RDMA Write reception of unaligned
payload, if the current skb did contain only the expected 3 padding
bytes, but not the 4 bytes CRC trailer. Expecting 4 more bytes already
arrived in another skb, and not consuming those 3 bytes in the current
upcall left the Write incomplete, waiting for the CRC forever.
Fixes: 8b6a361b8c48 ("rdma/siw: receive path") Reported-by: Olga Kornievskaia <kolga@netapp.com> Tested-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Link: https://lore.kernel.org/r/20220920081202.223629-1-bmt@zurich.ibm.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently ib_copy_from_udata and ib_copy_to_udata could underfill
the request and response buffer if the user-space passes an undersized
value for udata->inlen or udata->outlen respectively [1]
This could lead to undesirable behavior.
Zero initing the buffer only goes as far as preventing using the buffer
uninitialized.
Validate udata->inlen and udata->outlen passed from user-space to ensure
they are at least the required minimum size.
A number of asynchronous event (AE) ids were not aligned to the
correct flush_code and event_type. Fix these up so that the
correct IBV error and event codes are returned to application.
Also, add handling for new AE ids like IRDMA_AE_INVALID_REQUEST to
return the correct WC error code.
Commit f6424c22aa36 ("mtd: rawnand: fsl_elbc: Make SW ECC work") added
support for specifying ECC mode via DTS and skipping autodetection.
But it broke explicit specification of HW ECC mode in DTS as correct
settings for HW ECC mode are applied only when NONE mode or nothing was
specified in DTS file.
Also it started aliasing NONE mode to be same as when ECC mode was not
specified and disallowed usage of ON_DIE mode.
Fix all these issues. Use autodetection of ECC mode only in case when mode
was really not specified in DTS file by checking that ecc value is invalid.
Set HW ECC settings either when HW ECC was specified in DTS or it was
autodetected. And do not fail when ON_DIE mode is set.
The "intel,nand-controller" compatible string is not part of the
dt-bindings. Remove it from the driver as it's not supposed to be used
without any documentation for it.
As the of_get_parent() will increase the refcount of the node->parent
and the reference will be discarded, so we should hold the reference
with which we can decrease the refcount when done.
Fixes: 8eff8b4e22d9 ("phy: amlogic: phy-meson-axg-mipi-pcie-analog: add support for MIPI DSI analog") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220915093506.4009456-1-windhl@126.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct_size() macro protects against integer overflows but adding
"+ rsc->config_len" introduces the risk of integer overflows again.
Use size_add() to be safe.
Fixes: c87846571587 ("remoteproc: use struct_size() helper") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com> Link: https://lore.kernel.org/r/YyMyoPoGOJUcEpZT@kili Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This exported fn is unused, and will not be needed. Lets dump it.
The export was added to let drm control pr_debugs, as part of using
them to avoid drm_debug_enabled overheads. But its better to just
implement the drm.debug bitmap interface, then its available for
everyone.
Fixes: a2d375eda771 ("dyndbg: refine export, rename to dynamic_debug_exec_queries()") Fixes: 4c0d77828d4f ("dyndbg: export ddebug_exec_queries") Acked-by: Jason Baron <jbaron@akamai.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Link: https://lore.kernel.org/r/20220904214134.408619-10-jim.cromie@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dyndbg's control-parser: ddebug_parse_query(), requires that search
terms: module, func, file, lineno, are used only once in a query; a
thing cannot be named both foo and bar.
The cited commit added an overriding module modname, taken from the
module loader, which is authoritative. So it set query.module 1st,
which disallowed its use in the query-string.
But now, its useful to allow a module-load to enable classes across a
whole (or part of) a subsystem at once.
For CONFIG_DYNAMIC_DEBUG=N, the ddebug_dyndbg_module_param_cb()
stub-fn is too permissive:
bash-5.1# modprobe drm JUNKdyndbg
bash-5.1# modprobe drm dyndbgJUNK
[ 42.933220] dyndbg param is supported only in CONFIG_DYNAMIC_DEBUG builds
[ 42.937484] ACPI: bus type drm_connector registered
This caused no ill effects, because unknown parameters are either
ignored by default with an "unknown parameter" warning, or ignored
because dyndbg allows its no-effect use on non-dyndbg builds.
But since the code has an explicit feedback message, it should be
issued accurately. Fix with strcmp for exact param-name match.
Fixes: b48420c1d301 dynamic_debug: make dynamic-debug work for module initialization Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Jason Baron <jbaron@akamai.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Link: https://lore.kernel.org/r/20220904214134.408619-3-jim.cromie@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In https://lore.kernel.org/lkml/20211209150910.GA23668@axis.com/
Vincent's patch commented on, and worked around, a bug toggling
static_branch's, when a 2nd PRINTK-ish flag was added. The bug
results in a premature static_branch_disable when the 1st of 2 flags
was disabled.
The cited commit computed newflags, but then in the JUMP_LABEL block,
failed to use that result, instead using just one of the terms in it.
Using newflags instead made the code work properly.
This is Vincents test-case, reduced. It needs the 2nd flag to
demonstrate the bug, but it's explanatory here.
This from static analysis. The vla_item() takes a size and adds it to
the total. It has a built in integer overflow check so if it encounters
an integer overflow anywhere then it records the total as SIZE_MAX.
However there is an issue here because the "lang_count*(needed_count+1)"
multiplication can overflow. Technically the "lang_count + 1" addition
could overflow too, but that would be detected and is harmless. Fix
both using the new size_add() and size_mul() functions.
When we get a DMA channel and try to use it in multiple threads it
will cause oops and hanging the system.
% echo 100 > /sys/module/dmatest/parameters/threads_per_chan
% echo 100 > /sys/module/dmatest/parameters/iterations
% echo 1 > /sys/module/dmatest/parameters/run
[383493.327077] Unable to handle kernel paging request at virtual
address dead000000000108
[383493.335103] Mem abort info:
[383493.335103] ESR = 0x96000044
[383493.335105] EC = 0x25: DABT (current EL), IL = 32 bits
[383493.335107] SET = 0, FnV = 0
[383493.335108] EA = 0, S1PTW = 0
[383493.335109] FSC = 0x04: level 0 translation fault
[383493.335110] Data abort info:
[383493.335111] ISV = 0, ISS = 0x00000044
[383493.364739] CM = 0, WnR = 1
[383493.367793] [dead000000000108] address between user and kernel
address ranges
[383493.375021] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[383493.437574] CPU: 63 PID: 27895 Comm: dma0chan0-copy2 Kdump:
loaded Tainted: GO 5.17.0-rc4+ #2
[383493.457851] pstate: 204000c9 (nzCv daIF +PAN -UAO -TCO -DIT
-SSBS BTYPE=--)
[383493.465331] pc : vchan_tx_submit+0x64/0xa0
[383493.469957] lr : vchan_tx_submit+0x34/0xa0
This occurs because the transmission timed out, and that's due
to data race. Each thread rewrite channels's descriptor as soon as
device_issue_pending is called. It leads to the situation that
the driver thinks that it uses the right descriptor in interrupt
handler while channels's descriptor has been changed by other
thread. The descriptor which in fact reported interrupt will not
be handled any more, as well as its tx->callback.
That's why timeout reports.
With current fixes channels' descriptor changes it's value only
when it has been used. A new descriptor is acquired from
vc->desc_issued queue that is already filled with descriptors
that are ready to be sent. Threads have no direct access to DMA
channel descriptor. In case of channel's descriptor is busy, try
to submit to HW again when a descriptor is completed. In this case,
vc->desc_issued may be empty when hisi_dma_start_transfer is called,
so delete error reporting on this. Now it is just possible to queue
a descriptor for further processing.
Fixes: e9f08b65250d ("dmaengine: hisilicon: Add Kunpeng DMA engine support") Signed-off-by: Jie Hai <haijie1@huawei.com> Acked-by: Zhou Wang <wangzhou1@hisilicon.com> Link: https://lore.kernel.org/r/20220830062251.52993-4-haijie1@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After completion of data transfer of one or multiple descriptors,
the completion status and the current head pointer to submission
queue are written into the CQ and interrupt can be generated to
inform the software. In interrupt process CQ is read and cq_head
is updated.
hisi_dma_irq updates cq_head only when the completion status is
success. When an abnormal interrupt reports, cq_head will not update
which will cause subsequent interrupt processes read the error CQ
and never report the correct status.
This patch updates cq_head whenever CQ is accessed.
Fixes: e9f08b65250d ("dmaengine: hisilicon: Add Kunpeng DMA engine support") Signed-off-by: Jie Hai <haijie1@huawei.com> Acked-by: Zhou Wang <wangzhou1@hisilicon.com> Link: https://lore.kernel.org/r/20220830062251.52993-3-haijie1@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The otg sync state patch reuses the ret variable, but fails to set it to
zero after use. This leads to a situation when the otg port is in
peripheral mode where the otg phy aborts halfway through setup. It also
fails to account for a failure to register the extcon notifier. Fix this
by using our own variable and skipping otg sync in case of failure.
Fixes: 8dc60f8da22f ("phy: rockchip-inno-usb2: Sync initial otg state") Reported-by: Markus Reichl <m.reichl@fivetechno.de> Reported-by: Michael Riesch <michael.riesch@wolfvision.net> Signed-off-by: Peter Geis <pgwipeout@gmail.com> Tested-by: Michael Riesch <michael.riesch@wolfvision.net> Tested-by: Markus Reichl <m.reichl@fivetechno.de> Reviewed-by: Samuel Holland <samuel@sholland.org> Link: https://lore.kernel.org/r/20220902184543.1234835-1-pgwipeout@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pwrmcu is responsible for power management and idle states in SSPM:
on older SoCs this was managed in Linux drivers like sspm/mcupm/eemgpu
but, at least on MT8195, this functionality was transferred to the ATF
firmware.
For this reason, turning off the pwrmcu related clocks from the kernel
will lead to unability to resume the platform after suspend and other
currently unknown PM related side-effects.
Set the PWRMCU and PWRMCU_BUS_H clocks as critical to prevent the
kernel from turning them off, fixing the aforementioned issue.
Fixes: e2edf59dec0b ("clk: mediatek: Add MT8195 infrastructure clock support") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220719093316.37253-1-angelogioacchino.delregno@collabora.com Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Like it was done for the vdo0_dp_intf0_dp_intf clock (used for eDP),
add the CLK_SET_RATE_PARENT flag to CLK_VDO1_DPINTF (used for DP)
and also fix its parent clock name as it has to be "top_dp" for two
reasons:
- This is its real parent!
- Likewise to eDP/VDO0 counterpart, we need clock source
selection on CLK_TOP_DP.
Fixes: 269987505ba9 ("clk: mediatek: Add MT8195 vdosys1 clock support") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220816193257.658487-3-nfraprado@collabora.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the CLK_SET_RATE_PARENT flag to the CLK_VDO0_DP_INTF0_DP_INTF
clock: this is required to trigger clock source selection on
CLK_TOP_EDP, while avoiding to manage the enablement of the former
separately from the latter in the displayport driver.
Fixes: 70282c90d4a2 ("clk: mediatek: Add MT8195 vdosys0 clock support") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220816193257.658487-2-nfraprado@collabora.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: df3305156f98 ("[media] v4l: xilinx: Add Xilinx Video IP core") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
driver will enable the vpu core when request the first instance
on the core.
one vpu core can only support 8 streaming instances in the same
time, the instance won't be added to core's list before streamon.
so the actual instance count may be greater then the number in
the core's list.
in pm resume callback, driver will resume the core immediately if
core's list is not empty.
but this check is not accurate,
if suspend during one instance is requested, but not streamon,
then after suspend, the core won't be resume, and led to instance failure.
use the request_count instead of the core's list to check
whether is the core needed to resume immediately after suspend.
And it can make the pm suspend and resume callback more clear.
decoder will report the colorspace information
which is parsed from the sequence header,
if they are unspecified, just let application to determine it,
don't change it in driver.
adjust the value range of gop size from [0, 65535] to [1, 8000].
when the gop size is set to a too large value,
it may affect the encoded picture quality.
so constrain it to a reasonable range.
For format vc1, the amphion vpu requires driver to
help insert some custom startcode before sequence and frame.
the startcode is different for vc1l and vc1g format.
But the sequence startcode is only needed at the beginning,
and it's not expected after seek.
driver need to treat the codec header and the first frame after seek
as a normal frame, and insert picture startcode for it.
In previous patch, I just fix it for vc1l format,
and should fix the similar issue for vc1g too.
Fixes: e670f5d672ef (media: amphion: only insert the first sequence startcode for vc1l format) Signed-off-by: Ming Qian <ming.qian@nxp.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In fimc_is_register_subdevs(), we need to call of_node_put() for
the reference 'i2c_bus' when breaking out of the
for_each_compatible_node() which has increased the refcount.
In commit 3f905469c8ce ("clk: qcom: gcc: Use floor ops for SDCC clocks")
floor ops were applied to SDCC2 only, but flooring is also required on
the SDCC1 apps clock which is used by the eMMC card on Sony's Nile
platform, and otherwise result in the typicial "Card appears
overclocked" warnings observed on many other platforms before:
When returning or breaking early from a
for_each_available_child_of_node() loop, we need to explicitly call
of_node_put() on the child node to possibly release the node.
Fixes: b209e047bc74 ("HSI: Introduce OMAP SSI driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 37c26a906527 ("clk: tegra: add clock support for Tegra20") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220523152811.19692-1-linmq006@gmail.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 2cb5efefd6f7 ("clk: tegra: Implement clocks for Tegra114") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220523143834.7587-1-linmq006@gmail.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 6b301a059eb2 ("clk: tegra: Add support for Tegra210 clocks") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220523142608.65074-1-linmq006@gmail.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should hold the reference returned by of_get_parent() and use it
to call of_node_put() for refcount balance.
Fixes: f95e8c7923d1 ("clk: sprd: support to get regmap from parent node") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220704004729.272481-1-windhl@126.com Reviewed-by: Orson Zhai <orsonzhai@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In berlin2_clock_setup() and berlin2q_clock_setup(), we need to
call of_node_put() for the reference returned by of_get_parent()
which has increased the refcount. We should call *_put() in fail
path or when it is not used anymore.
Previously usb_decode_ctrl() only decodes standard control requests, but
it was used for non-standard requests also. If it's non-standard or
unknown standard bRequest, print the Setup data values.
According to the ib spec:
If the CI supports the Base Memory Management Extensions defined in this
specification, the L_Key format must consist of:
24 bit index in the most significant bits of the R_Key, and
8 bit key in the least significant bits of the R_Key
Through a successful Allocate L_Key verb invocation, the CI must let the
consumer own the key portion of the returned R_Key
Therefore, when creating a mkey using DEVX, the consumer is allowed to
change the key part. The kernel should compare only the index part of a
R_Key to determine equality with another R_Key.
Adding capability in order not to break backward compatibility.
The "hard_offsets" are currently unsigned u8 but they should be signed as they
can get negative. They are signed in function yas5xx_meaure_offsets() and in the
Yamaha drivers [1][2].
of_iio_channel_get_by_name() can either return NULL or an error pointer
so that only doing IS_ERR() is not enough. Fix it by checking the NULL
pointer case and return -ENODEV in that case. Note this is done like this
so that users of the function (which only check for error pointers) do
not need to be changed. This is not ideal since we are losing error codes
and as such, in a follow up change, things will be unified so that
of_iio_channel_get_by_name() only returns error codes.
Fixes: 6e39b145cef7 ("iio: provide of_iio_channel_get_by_name() and devm_ version it") Signed-off-by: Nuno Sá <nuno.sa@analog.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220715122903.332535-3-nuno.sa@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
'of_node_put()' can potentially release the memory pointed to by
'iiospec.np' which would leave us with an invalid pointer (and we would
still pass it in 'of_xlate()'). Note that it is not guaranteed for the
of_node lifespan to be attached to the device (to which is attached)
lifespan so that there is (even though very unlikely) the possibility
for the node to be freed while the device is still around. Thus, as there
are indeed some of_xlate users which do access the node, a race is indeed
possible.
As such, we can only release the node after we are done with it.
Fixes: 17d82b47a215d ("iio: Add OF support") Signed-off-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20220715122903.332535-2-nuno.sa@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case triggered buffers are enabled while system is suspended they will
not work anymore after resume. For this call at91_adc_buffer_postdisable()
on suspend and at91_adc_buffer_prepare() on resume. On tests it has been
seen that at91_adc_buffer_postdisable() call is not necessary but it has
been kept because it also does the book keeping for DMA. On resume path
there is no need to call at91_adc_configure_touch() as it is embedded in
at91_adc_buffer_prepare().
Fixes: 073c662017f2f ("iio: adc: at91-sama5d2_adc: add support for DMA") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220803102855.2191070-5-claudiu.beznea@microchip.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
.read_raw()/.write_raw() could be called asynchronously from user space
or other in kernel drivers. Without locking on st->lock these could be
called asynchronously while there is a conversion in progress. Read will
be harmless but changing registers while conversion is in progress may
lead to inconsistent results. Thus, to avoid this lock st->lock.
Fixes: 27e177190891 ("iio:adc:at91_adc8xx: introduce new atmel adc driver") Fixes: 6794e23fa3fe ("iio: adc: at91-sama5d2_adc: add support for oversampling resolution") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220803102855.2191070-4-claudiu.beznea@microchip.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This crash is a result of iomap_writepage_map encountering some sort of
error during writeback and wanting to set that error code in the file
mapping so that fsync will report it. Unfortunately, the code
dereferences folio->mapping after unlocking the folio, which means that
another thread could have removed the page from the page cache
(writeback doesn't hold the invalidation lock) and give it to somebody
else.
At best we crash the system like above; at worst, we corrupt memory or
set an error on some other unsuspecting file while failing to record the
problems with *this* file. Regardless, fix the problem by reporting the
error to the inode mapping.
NOTE: Commit 598ecfbaa742 lifted the XFS writeback code to iomap, so
this fix should be backported to XFS in the 4.6-5.4 kernels in addition
to iomap in the 5.5-5.19 kernels.
Fixes: e735c0079465 ("iomap: Convert iomap_add_to_ioend() to take a folio") # 5.17 onward Fixes: 598ecfbaa742 ("iomap: lift the xfs writeback code to iomap") # 5.5-5.16, needs backporting Fixes: 150d5be09ce4 ("xfs: remove xfs_cancel_ioend") # 4.6-5.4, needs backporting Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
EHCI Oxynos (drivers/usb/host/ehci-exynos.c) drives VBUS GPIO high when
trying to power up the bus, therefore the GPIO in DTS must be marked as
"active high". This will be important when EHCI driver is converted to
gpiod API that respects declared polarities.
Fixes: 4e8991def565 ("ARM: dts: exynos: Enable AX88760 USB hub on Origen board") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Link: https://lore.kernel.org/r/20220927220504.3744878-1-dmitry.torokhov@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a module PLTs are used and a module is loaded sufficiently far away
from the kernel, we'll create PLTs for any branches which are
out-of-range. These are separate from the special ftrace trampoline
PLTs, which the module PLT code doesn't directly manipulate.
When mcount is in use this is a problem, as each mcount callsite in a
module will be initialized to point to a module PLT, but since commit a6253579977e4c6f ftrace_make_nop() will assume that the callsite has
been initialized to point to the special ftrace trampoline PLT, and
ftrace_find_callable_addr() rejects other cases.
This means that when ftrace tries to initialize a callsite via
ftrace_make_nop(), the call to ftrace_find_callable_addr() will find
that the `_mcount` stub is out-of-range and is not handled by the ftrace
PLT, resulting in a splat:
Fix this by reverting to the old behaviour of ignoring the old
instruction when initialising an mcount callsite in a module, which was
the behaviour prior to commit a6253579977e4c6f.
On a read-only filesystem, we won't invoke the block allocator, so we
don't need to prefetch the block bitmaps.
This avoids starting and running the ext4lazyinit thread at all on a
system with no read-write ext4 filesystems (for instance, a container VM
with read-only filesystems underneath an overlayfs).
On arm32, the configuration options to specify the kernel command line
type depend on ATAGS. However, the actual CMDLINE cofiguration option
does not depend on ATAGS, and the code that handles this is not specific
to ATAGS (see drivers/of/fdt.c:early_init_dt_scan_chosen()).
Hence users who desire to override the kernel command line on arm32 must
enable support for ATAGS, even on a pure-DT system. Other architectures
(arm64, loongarch, microblaze, nios2, powerpc, and riscv) do not impose
such a restriction.
Hence drop the dependency on ATAGS.
Fixes: bd51e2f595580fb6 ("ARM: 7506/1: allow for ATAGS to be configured out when DT support is selected") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to s5k6a3 driver code, the reset line for the chip appears to
be active low. This also matches the typical polarity of reset lines in
general. Let's fix it up as having correct polarity in DTS is important
when the driver will be switched over to gpiod API.
Range size of 0x2b4 was incorrect since there isn't 173 configurable
pins for muxing. Additionally there is a non-addressable region in the
mapping which requires splitting into two ranges.
main_pmx0 -> 67 pins
main_pmx1 -> 3 pins
Fixes: d361ed88455f ("arm64: dts: ti: Add support for J7200 SoC") Signed-off-by: Matt Ranostay <mranostay@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Vaishnav Achath <vaishnav.a@ti.com> Link: https://lore.kernel.org/r/20220919205723.8342-1-mranostay@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The DMA subsystem could be entirely disabled in Kconfig and then the
TEGRA20_APB_DMA option isn't available too. Hence kernel configuration
fails if DMADEVICES Kconfig option is disabled due to the unsatisfiable
dependency.
The FUSE driver isn't a critical driver and currently it only provides
NVMEM interface to userspace which isn't known to be widely used, and
thus, it's fine if FUSE driver fails to load.
Let's remove the erroneous Kconfig dependency and let the FUSE driver to
fail the probing if DMA is unavailable.
Both the Linkstation LS-CHLv2 and the LS-XHL have only one ethernet
port. This has always been wrong, i.e. the board code used to set up
both ports, but the driver will play nice and return -ENODEV if the
assiciated PHY is not found. Nevertheless, it is wrong. Remove it.
Fixes: 876e23333511 ("ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 327e15428977 ("ARM: dts: kirkwood: consolidate common pinctrl
settings") unknowingly broke the serial output on this board. Before
this commit, the pinmux was still configured by the bootloader and the
kernel didn't reconfigured it again. This was an oversight by the
initial board support where the pinmux for the serial line was never
configured by the kernel. But with this commit, the serial line will be
reconfigured to the wrong pins. This is especially confusing, because
the output still works, but the input doesn't. Presumingly, the input is
reconfigured to MPP10, but the output is connected to both MPP11 and
MPP5.
Override the pinmux in the board device tree.
Fixes: 327e15428977 ("ARM: dts: kirkwood: consolidate common pinctrl settings") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a bug in Turris Omnia's schematics, whereupon the MPP[26] pin,
which is routed to CN11 pin header, is documented as SPI CS1, but
MPP[26] pin does not support this function. Instead it controls chip
select 2 if in "spi0" mode.
Fix the name of the pin node in pinctrl node and fix the comment in SPI
node.
Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia") Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c2 is routed to the pins dedicated as DDC in the module standard.
Reduce clock rate to 100kHz to be in line with VESA standard and hook
this bus up to the HDMI node.
In qcom_smem_state_register() and qcom_smem_state_release(), we
should better use of_node_get() and of_node_put() for the reference
creation and destruction of 'device_node'.
Fixes: 9460ae2ff308 ("soc: qcom: Introduce common SMEM state machine code") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220721135217.1301039-2-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two refcount leak bugs in qcom_smsm_probe():
(1) The 'local_node' is escaped out from for_each_child_of_node() as
the break of iteration, we should call of_node_put() for it in error
path or when it is not used anymore.
(2) The 'node' is escaped out from for_each_available_child_of_node()
as the 'goto', we should call of_node_put() for it in goto target.
Thread A trying to acquire a write lease checks the value of i_readcount
and i_writecount in check_conflicting_open() to verify that its own fd
is the only fd referencing the file.
Thread B trying to open the file for read will call break_lease() in
do_dentry_open() before incrementing i_readcount, which leaves a small
window where thread A can acquire the write lease and then thread B
completes the open of the file for read without breaking the write lease
that was acquired by thread A.
Fix this race by incrementing i_readcount before checking for existing
leases, same as the case with i_writecount.
Use a helper put_file_access() to decrement i_readcount or i_writecount
in do_dentry_open() and __fput().
Fixes: 387e3746d01c ("locks: eliminate false positive conflicts for write lease") Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should add the of_node_put() when breaking out of
for_each_child_of_node() as it will automatically increase
and decrease the refcount.
Fixes: e6b42eb6a66c ("memory: emif: add device tree support to emif driver") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220719085640.1210583-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The break of for_each_available_child_of_node() needs a
corresponding of_node_put() when the reference 'child' is not
used anymore. Here we do not need to call of_node_put() in
fail path as '!match' means no break.
While the of_platform_device_create() will created a new
reference by 'child' but it has considered the refcounting.
Fixes: fee10bd22678 ("memory: pl353: Add driver for arm pl353 static memory controller") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220716031324.447680-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The HDMI driver skips the notification handling from the graphics
driver when the codec driver is being in the PM operation. This
behavior was introduced by the commit eb399d3c99d8 ("ALSA: hda - Skip
ELD notification during PM process"). This skip may cause a problem,
as we may miss the ELD update when the connection/disconnection
happens right at the runtime-PM operation of the audio codec.
Although this workaround was valid at that time, it's no longer true;
the fix was required just because the ELD update procedure needed to
wake up the audio codec, which had lead to a runtime-resume during a
runtime-suspend. Meanwhile, the ELD update procedure doesn't need a
codec wake up any longer since the commit 788d441a164c ("ALSA: hda -
Use component ops for i915 HDMI/DP audio jack handling"); i.e. there
is no much reason for skipping the notification.
Let's drop those checks for addressing the missing notification.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of mt6660_i2c_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm5102_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm5110_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm8997_probe
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of stm32_i2s_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of stm32_spdifrx_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of stm32_adfsdm_probe.
Fixes:98e500a12f934 ("ASoC: stm32: dfsdm: add pm_runtime support for audio")
projects / thirdparty / kernel / stable.git / log
