Specifications:
CPU: MT7621A dual-core 880MHz
RAM: 64MB DDR2
FLASH: 16MB MX25L12805D NOR SPI
WIFI: 2.4GHz 2x2 MT7603 b/g/n PCI
WIFI: 5GHz 2x2 MT7662 a/b/ac PCI
ETH: 1xLAN 1000base-T integrated
SWITCH: MT7530 Port 0: LAN, Port 6: CPU
LED: Power, 2.4GHz WiFi, 5GHz WiFi
BTN: WPS, Reset
UART: Near ETH port, from ETH: 3V3-TxD-GND-RxD 57600 8n1
MISC: Audio support
Installation:
1. Update using recovery mode
- while holdig "reset" button, power on the device
- keep holding "reset" until power led is flashing yellow
- set own IP to 192.168.1.75, subnet mask: 255.255.255.0
- push firmware image (can be factory.bin or sysupgrade.bin)
using tftp client in binary mode to 192.168.1.1
Notes:
This board has only two MAC addresses programmed in the "factory" partition:
- MAC for wlan0 (2.4GHz) at offset 0x0004
- MAC for wlan1 (5GHz) at offset 0x8004
- stock firmware re-uses wlan0 MAC for ethernet
- no valid addresses found in 0x28, 0x2e, 0xe000 and 0xe006
Nick Hainke [Wed, 3 Aug 2022 05:13:08 +0000 (07:13 +0200)]
elfutils: update to 0.187
Changes:
debuginfod: Support -C option for connection thread pooling.
debuginfod-client: Negative cache file are now zero sized instead of
no-permission files.
addr2line: The -A, --absolute option, which shows file names including
the full compilation directory is now the default. To get the
old behavior use the new option --relative.
libdw, debuginfo-client: Load libcurl lazily only when files need to
be fetched remotely. libcurl is now never
loaded when DEBUGINFOD_URLS is unset. And when
DEBUGINFOD_URLS is set, libcurl is only loaded
when the debuginfod_begin function is called.
Petr Štetiar [Sat, 6 Aug 2022 12:55:07 +0000 (14:55 +0200)]
zlib: backport fix for heap-based buffer over-read (CVE-2022-37434)
zlib through 1.2.12 has a heap-based buffer over-read or buffer overflow
in inflate in inflate.c via a large gzip header extra field. NOTE: only
applications that call inflateGetHeader are affected. Some common
applications bundle the affected zlib source code but may be unable to
call inflateGetHeader.
Fixes: CVE-2022-37434
References: https://github.com/ivd38/zlib_overflow Signed-off-by: Petr Štetiar <ynezz@true.cz>
realtek: add support for Panasonic Switch-M48eG PN28480K
Panasonic Switch-M48eG PN28480K is a 48 + 4 port gigabit switch, based on
RTL8393M.
Specification:
- SoC : Realtek RTL8393M
- RAM : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x48 + 2
- port 1-40 : TP, RTL8218B x5
- port 41-48 : RTL8218FB
- port 41-44: TP
- port 45-48: TP/SFP (Combo)
- LEDs/Keys : 7x / 1x
- UART : RS-232 port on the front panel (connector: RJ-45)
- 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
- 9600n8
- Power : 100-240 VAC, 50/60 Hz, 0.5 A
- Plug : IEC 60320-C13
- Stock OS : VxWorks based
Flash instruction using initramfs image:
1. Prepare the TFTP server with the IP address 192.168.1.111
2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
the TFTP directory
3. Download the official upgrading firmware (ex: pn28480k_v30000.rom)
and place it to the TFTP directory
4. Boot M48eG and interrupt the U-Boot with Ctrl + C keys
5. Execute the following commands and boot with the OpenWrt initramfs
image
rtk network on
tftpboot 0x81000000
bootm
6. Backup mtdblock files to the computer by scp or anything and reboot
7. Interrupt the U-Boot and execute the following commands to re-create
filesystem in the flash
ffsmount c:/
ffsfmt c:/
this step takes a long time, about ~ 4 mins
8. Execute the following commands to put the official images to the
filesystem
updatert <official image>
example:
updatert pn28480k_v30000.rom
this step takes about ~ 40 secs
9. Set the environment variables of the U-Boot by the following commands
11: On the initramfs image, download the sysupgrade image and perform
sysupgrade with it
sysupgrade <imagename>
12: Wait ~ 120 seconds to complete flashing
Known Issues:
- 4x SFP ports are provided as combo ports by the RTL8218FB chip, but the
phy driver has no support for it. Currently, only TP ports work by the
RTL8218B support.
Note:
- "Switch-M48eG" is a model name, and "PN28480K" is a model number.
Switch-M48eG has an another (old) model number ("PN28480"), it's not a
Realtek based hardware.
- Switch-M48eG has a "POWER" LED (Green), but it's not connected to any
GPIO pin.
- U-Boot checks the runtime images in the flash when booting and fails
to execute "bootcmd" variable if the images are not existing.
- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
firmware and it includes the stock images, configuration files and
checksum files. It's unknown format, can't be managed on the OpenWrt.
To get the enough space for OpenWrt, move the filesystem to the head
of "fs_reserved" partition by execution of "ffsfmt" and "updatert".
- A GPIO pin on PCA9539 is used for resetting external RTL8218B phys and
RTL8218FB phy.
This should be specified as "reset-gpios" property in MDIO node, but
the current configuration of RTL8218B phy in the driver seems to be
incomplete and RTL8218FB won't be configured on RTL8218D support.
So, ethernet ports on these phys will be broken after hard-resetting.
At the moment, configure this pin as gpio-hog to avoid breaking by
resetting.
- This model has 2x Microchip TCN75A thermal sensors. Linux Kernel
supports TCN75 chip on lm75 driver, but no support for TCN75'A'
variant.
At the moment, use TCN75 support for the chips instead.
Back to the stock firmware:
1. Delete "loadaddr" variable and set "bootcmd" to the original value
realtek: enable pca953x GPIO driver for rtl839x subtarget
The system status LED on Panasonic Switch-M48eG PN28480K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.
realtek: add support for Panasonic Switch-M24eG PN28240K
Panasonic Switch-M24eG PN28240K is a 24 + 2 port gigabit switch, based on
RTL8382M.
Specification:
- SoC : Realtek RTL8382M
- RAM : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x24 + 2
- port 1-8 : TP, RTL8218B
- port 9-16 : TP, RTL8218B (SoC)
- port 17-24 : RTL8218FB
- port 17-22: TP
- port 23-24: TP/SFP (Combo)
- LEDs/Keys : 7x / 1x
- UART : RS-232 port on the front panel (connector: RJ-45)
- 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
- 9600n8
- Power : 100-240 VAC, 50/60 Hz, 0.5 A
- Plug : IEC 60320-C13
- Stock OS : VxWorks based
Flash instruction using initramfs image:
1. Prepare the TFTP server with the IP address 192.168.1.111
2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
the TFTP directory
3. Download the official upgrading firmware (ex: pn28240k_v30000.rom)
and place it to the TFTP directory
4. Boot M24eG and interrupt the U-Boot with Ctrl + C keys
5. Execute the following commands and boot with the OpenWrt initramfs
image
rtk network on
tftpboot 0x81000000
bootm
6. Backup mtdblock files to the computer by scp or anything and reboot
7. Interrupt the U-Boot and execute the following commands to re-create
filesystem in the flash
ffsmount c:/
ffsfmt c:/
this step takes a long time, about ~ 4 mins
8. Execute the following commands to put the official images to the
filesystem
updatert <official image>
example:
updatert pn28240k_v30000.rom
this step takes about ~ 40 secs
9. Set the environment variables of the U-Boot by the following commands
11: On the initramfs image, download the sysupgrade image and perform
sysupgrade with it
sysupgrade <imagename>
12: Wait ~ 120 seconds to complete flashing
Known Issues:
- 2x SFP ports are provided as combo ports by the RTL8218FB chip, but the
phy driver has no support for it. Currently, only TP ports work by the
RTL8218D support.
Note:
- "Switch-M24eG" is a model name, and "PN28240K" is a model number.
Switch-M24eG has an another (old) model number ("PN28240"), it's not a
Realtek based hardware.
- Switch-M24eG has a "POWER" LED (Green), but it's not connected to any
GPIO pin.
- U-Boot checks the runtime images in the flash when booting and fails
to execute "bootcmd" variable if the images are not existing.
- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
firmware and it includes the stock images, configuration files and
checksum files. It's unknown format, can't be managed on the OpenWrt.
To get the enough space for OpenWrt, move the filesystem to the head
of "fs_reserved" partition by execution of "ffsfmt" and "updatert".
- A GPIO pin on PCA9539 is used for resetting external RTL8218B phy and
RTL8218FB phy.
This should be specified as "reset-gpios" property in MDIO node, but
the current configuration of RTL8218B phy in the phy driver seems to
be incomplete and RTL8218FB won't be configured on RTL8218D support.
So, ethernet ports on these phys will be broken after hard-resetting.
At the moment, configure this pin as gpio-hog to avoid breaking by
resetting.
Back to the stock firmware:
1. Delete "loadaddr" variable and set "bootcmd" to the original value
realtek: add support for Panasonic Switch-M16eG PN28160K
Panasonic Switch-M16eG PN28160K is a 16 + 2 port gigabit switch, based on
RTL8382M.
Specification:
- SoC : Realtek RTL8382M
- RAM : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x16 + 2
- port 1-8 : TP, RTL8218B (SoC)
- port 9-16 : RTL8218FB
- port 9-14: TP
- port 15-16: TP/SFP (Combo)
- LEDs/Keys : 7x / 1x
- UART : RS-232 port on the front panel (connector: RJ-45)
- 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
- 9600n8
- Power : 100-240 VAC, 50/60 Hz, 0.5 A
- Plug : IEC 60320-C13
- Stock OS : VxWorks based
Flash instruction using initramfs image:
1. Prepare the TFTP server with the IP address 192.168.1.111
2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
the TFTP directory
3. Download the official upgrading firmware (ex: pn28160k_v30003.rom)
and place it to the TFTP directory
4. Boot M16eG and interrupt the U-Boot with Ctrl + C keys
5. Execute the following commands and boot with the OpenWrt initramfs
image
rtk network on
tftpboot 0x81000000
bootm
6. Backup mtdblock files to the computer by scp or anything and reboot
7. Interrupt the U-Boot and execute the following commands to re-create
filesystem in the flash
ffsmount c:/
ffsfmt c:/
this step takes a long time, about ~ 4 mins
8. Execute the following commands to put the official images to the
filesystem
updatert <official image>
example:
updatert pn28160k_v30003.rom
this step takes about ~ 40 secs
9. Set the environment variables of the U-Boot by the following commands
11: On the initramfs image, download the sysupgrade image and perform
sysupgrade with it
sysupgrade <imagename>
12: Wait ~ 120 seconds to complete flashing
Known Issues:
- 2x SFP ports are provided as combo ports by the RTL8218FB chip, but the
phy driver has no support for it. Currently, only TP ports work by the
RTL8218D support.
Note:
- "Switch-M16eG" is a model name, and "PN28160K" is a model number.
Switch-M16eG has an another (old) model number ("PN28160"), it's not a
Realtek based hardware.
- Switch-M16eG has a "POWER" LED (Green), but it's not connected to any
GPIO pin.
- U-Boot checks the runtime images in the flash when booting and fails
to execute "bootcmd" variable if the images are not existing.
- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
firmware and it includes the stock images, configuration files and
checksum files. It's unknown format, can't be managed on the OpenWrt.
To get the enough space for OpenWrt, move the filesystem to the head
of "fs_reserved" partition by execution of "ffsfmt" and "updatert".
- A GPIO pin on PCA9539 is used for resetting external RTL8218FB phy.
This should be specified as "reset-gpios" property in MDIO node, but
RTL8218FB won't be configured on RTL8218D support in the phy driver.
So, ethernet ports on the phy will be broken after hard-resetting.
At the moment, configure this pin as gpio-hog to avoid breaking by
resetting.
Back to the stock firmware:
1. Delete "loadaddr" variable and set "bootcmd" to the original value
Wenli Looi [Mon, 1 Aug 2022 03:22:32 +0000 (03:22 +0000)]
ramips: support fw_printenv for Netgear WAX202
Config partition contains uboot env for the first 0x20000 bytes.
The rest of the partition contains other data including the device MAC
address and the password printed on the label.
Leo Soares [Sun, 31 Jul 2022 14:21:42 +0000 (15:21 +0100)]
kernel: add kmod-usb-hid-mcp2221
"The MCP2221 is a USB-to-UART/I2C serial converter which enables
USB connectivity in applications that have a UART and I2C interfaces."
<https://www.microchip.com/en-us/product/MCP2221>
Signed-off-by: Leo Soares <leo@hyper.ag>
(replaced GPIOLIB KConfig with @GPIO_SUPPORT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Paul Spooren [Tue, 19 Jul 2022 13:24:59 +0000 (15:24 +0200)]
x86: add missing Lex 3I380NX network detection
The Lex 3I380NX industrial PC has 4 ethernet controllers on board
which need pmc_plt_clk0 - 3 to function, add it to the critclk_systems
DMI table, so that drivers/clk/x86/clk-pmc-atom.c will mark the clocks
as CLK_CRITICAL and they will not get turned off.
This commit is nearly redundant to 3d0818f5eba8 ("platform/x86:
pmc_atom: Add Lex 3I380D industrial PC to critclk_systems DMI table")
but for all Lex Baytrail devices.
The original vendor firmware is only available using the WaybackMachine:
http://www.lex.com.tw/products/3I380NX.html
Signed-off-by: Michael Schöne <michael.schoene@rhebo.com> Signed-off-by: Paul Spooren <paul.spooren@rhebo.com>
(Hans broader version for more Lex Baytrail systems, v5.15) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Roland Barenbrug [Wed, 29 Jun 2022 11:09:25 +0000 (13:09 +0200)]
ltq-vdsl-app: Fix counter overflow resulting in negative values
The re-transmit counters can overflow the 32 bit representation resulting
in negative values being displayed. Background being that the numbers are
treated at some point as signed INT rather than unsigned INT.
Change the counters from 32 bit to 64 bit, should provide sufficient room
to avoid any overflow. Not the nicest solution but it works
Fixes: #10077 Signed-off-by: Roland Barenbrug <roland@treslong.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Mark Mentovai [Sun, 10 Jul 2022 23:43:05 +0000 (19:43 -0400)]
libmnl: fix build when bash is not located at /bin/bash
This fixes the libmnl build on macOS, which ships with an outdated bash
at /bin/bash. During the OpenWrt build, a modern host bash is built and
made available at staging_dir/host/bin/bash, which is present before
/bin/bash in the build's PATH.
This is similar to 8f7ce3aa6dda, presently appearing at
package/kernel/mac80211/patches/build/001-fix_build.patch.
Shiji Yang [Sun, 20 Mar 2022 15:42:37 +0000 (23:42 +0800)]
ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
MAC Address:
use address(sample 1) address(sample 2) source
label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr
lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1
wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label
WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode)
WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode)
WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7
WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Andre Heider [Tue, 21 Jun 2022 12:09:21 +0000 (14:09 +0200)]
arm-trusted-firmware-mvebu: bump mv-ddr-marvell to current version
6ff988f mv_ddr: a3700: Use the right size for memset to not overflow 0f3e893 mv_ddr: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision 4bae770 mv_ddr: a38x: fix SPLIT_OUT_MIX state decision cdefd8b mv_ddr: a38x: Fix Synchronous vs Asynchronous mode determination 8c42ad9 mv_ddr_4_training: cast uint64_t to unsigned long long
Michael Pratt [Wed, 20 Jul 2022 23:17:22 +0000 (19:17 -0400)]
tools/libressl: disable assembly code for all hosts
This SSL library is for hosts only
and not shipped as a build product,
therefore its performance quality (speed) is not critical.
Assembly code is broken in LibreSSL for some x86_64 hosts (part of git history)
and for some RISC host archs like armv7l, aarch64, powerpc, ppc64, etc...
so let's just disable it for all hosts.
For example, this fixes an instance on ARM hosts
where the host Python 3 builds broken modules which link to LibreSSL,
even with patches that enable LibreSSL support
with the import error "unexpected reloc type 3".
Ref: a395563f6 ("build: fix libressl build on x32 (amd64ilp32) host ") Suggested-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Michael Pratt <mcpratt@pm.me>
Line up configure arguments for cleaner git diff and editing and grepping.
LibreSSL must be built with PIC, and has the flags for it already in CFLAGS.
Add the configure option native to LibreSSL to use only PIC in objects,
which further enforces that each object in the library has the PIC flag
to prevent a mixture of PIC / non-PIC objects within it.
Ref: 96a940308 ("tools: libressl: always build as PIC") Signed-off-by: Michael Pratt <mcpratt@pm.me>
Version 22.00 of 7z causes build failures on systems using GCC 12 with
the following error:
../../../../C/LzmaEnc.c: In function 'LzmaEnc_CodeOneMemBlock':
../../../../C/LzmaEnc.c:2996:19: error: storing the address of local
variable 'outStream' in '*p.rc.outStream' [-Werror=dangling-pointer=]
2996 | p->rc.outStream = &outStream.vt;
| ~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
../../../../C/LzmaEnc.c:2979:28: note: 'outStream' declared here
2979 | CLzmaEnc_SeqOutStreamBuf outStream;
| ^~~~~~~~~
../../../../C/LzmaEnc.c:2979:28: note: 'pp' declared here
Upgrade to version 22.01 which contains the required fix.
Fixes: 5fcc6f0f1942 ("tools: add 7z host package") Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net>
Nick Hainke [Tue, 26 Jul 2022 14:18:51 +0000 (16:18 +0200)]
libcap: update to 2.65
Changes: a47d86d Up the release version to 2.65 fc99e56 Include more signatures in pgp.keys.asc. 52288cc Close out this comment in the go/Makefile eb0f1df Prevent 'capsh --user=xxx --' from generating a bash error. 9a95791 Improve documentation for cap_get_pid and cap_reset_ambient. 21d08b0 Fix syntax error in DEBUG protected setcap.c code. 9425048 More useful captree usage string and man page.
Nick Hainke [Tue, 26 Jul 2022 14:16:27 +0000 (16:16 +0200)]
libcap: update to 2.64
Changes: 38cfa2e Up the release version to 2.64 7617af6 Avoid a deadlock in forked psx thread exit. fc029cb Include LIBCAP_{MAJOR,MINOR} #define's in sys/capability.h ceaa591 Clarify how the cap_get_pid() argument is interpreted. 15cacf2 Fix prctl return code/errno handling in libcap. aae9374 Be explicit about CGO_ENABLED=1 for compare-cap build. 66a8a14 psx: free allocated memory at exit.
Targets which allow booting from NVMe (x86, maybe some mvebu boards come
to mind) should have it built-in, so rootfs can be mounted from there.
For targets without NVMe support in bootloader or BIOS/firmware it's
sufficient to provide the kernel module package.
On targets having the NVMe driver built-in the resulting kmod package
is an empty dummy. In any case, depending on or installing kmod-nvme
results in driver support being available (either because it was already
built-in or because the relevant kernel modules are added and loaded).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Disable the usage of target specific CPU crypto instructions by default
to allow the package being shared again. Since WolfSSL does not offer
a stable ABI or a long term support version suitable for OpenWrt release
timeframes, we're forced to frequently update it which is greatly
complicated by the package being nonshared.
People who want or need CPU crypto instruction support can enable it in
menuconfig while building custom images for the few platforms that support
them.
Without packet steering NAT masquarade speed on BCM4908 /jumps/ between
two speeds:
1. 826 Mb/s (±3 Mb/s)
2. 909 Mb/s (±8 Mb/s)
and it never reaches ~940 Mb/s.
Proper packet steering can improve it. Below are testing results for
running iperf TCP traffic from LAN to WAN. They were used to pick up
golden values.
Support for HPE 1920 images depends on two non-existent tools (mkh3cimg
and mkh3cvfs) from the in the firmware-utils package. Revert commit f2f09bc00280 ("realtek: add support for HPE 1920 series") until support
for these tools is merged and made available in OpenWrt.
- Common:
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Jan Hoffmann [Sat, 23 Jul 2022 20:53:18 +0000 (22:53 +0200)]
tools: add 7z host package
Add the 7zr command line tool, which is a version of the 7z application
that only supports 7z archives.
7z is one of the two compression formats supported in H3C firmware
images (the alternative would be ARJ).
(Alternatively, the 7zr command line tool could also be built from a
current version of the public-domain LZMA SDK. That would require
repackaging the source package, as it is only provided in 7z format.)
Jan Hoffmann [Sat, 23 Jul 2022 20:53:17 +0000 (22:53 +0200)]
kernel: mtdsplit: add support for H3C VFS filesystem
The bootloader on some H3C devices (for example HPE 1920 switches) only
supports booting from flash by reading an image from an "VFS" filesystem
which spans most of the available flash. The filesystem size is hard-
coded in the bootloader. However, as long as no write operations are
performed in the bootloader menu, it is sufficient if the start of the
partition contains a valid filesystem with the kernel image.
This mtdsplit parser reads the size and location of the kernel image and
finds the location of the rootfs stored after it. It assumes that the
filesystem image matches the layout of one generated by mkh3cvfs, with
a filename of "openwrt-kernel.bin" for the kernel image.
Jan Hoffmann [Sat, 23 Jul 2022 20:53:16 +0000 (22:53 +0200)]
realtek: clean up rtl838x MDIO busy wait loop
Don't use udelay to allow other kernel tasks to execute if the kernel
has been built without preemption. Also determine the timeout based on
jiffies instead of loop iterations.
This is especially important on devices containing a watchdog with a
short timeout. Without this change, the watchdog is not serviced during
PHY patching which can take multiple seconds.
Tested-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Sat, 23 Jul 2022 20:53:15 +0000 (22:53 +0200)]
realtek: add SFP support for RTL8214FC PHY
Probe the SFP module during PHY initialization and implement
insertion/removal handlers to automatically configure the media type
of the respective port.
Jan Hoffmann [Sat, 23 Jul 2022 20:53:14 +0000 (22:53 +0200)]
realtek: rtl83xx-phy: decouple RTL8214FC media change and power config
Move RTL8214FC power configuration to newly created suspend and resume
methods. A media change now only results in power configuration if the
PHY is not suspended, to avoid powering up a port when the interface is
currently not up.
While at it, remove the rtl8380 prefix from function names, as this is
actually not SoC-specific.
Tested-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Sat, 23 Jul 2022 20:53:13 +0000 (22:53 +0200)]
realtek: rtl83xx-phy: fix RTL8214FC media change
Toggle power on the individual PHY instead of the package. Otherwise
a media change always toggles power on the first port, and not the one
that is being configured.
realtek: make DGS-1210 u-boot-env partition writeable
We are close to provide enduser friendly OpenWrt images for DGS-1210
switches that do not need serial console. Nevertheless a small bit is
missing. We cannot switch back to the vendor partition or initiate a
download of a vendor firmware image. To issue this from inside OpenWrt
we need write access to U-Boot environment.
Case 1: Switch back to secondary (vendor) image
> fw_setenv bootcmd run addargs\; bootm 0xb4e80000
> fw_setenv image /dev/mtdblock7
> reboot
Case 2: Issue D-Link Network Assistant based download on next reboot.
This is a combination of some vendor specific protocol (DDP) and a
TFTP download afterwards.
> fw_setenv bootstop on
> reboot
Allow these commands by opening up u-boot-env for write access.
Tested on DGS-1210-20.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
In theory we could have just 1 bootfs image for all devices as each
device has its own entry in the "configurations" node. It doesn't work
well with default configuration though.
If something goes wrong U-Boot SPL can be interrupted (by pressing A) to
enter its minimalistic menu. It allows ignoring boardid. In such case
bootfs default configuration is used.
For above reason each SoC family (BCM4908, BCM4912) should have its own
bootfs built. It allows each of them to have working default
configuration.
Openwrt now supports only glibc and musl. Add support for musl and
rework the libc check to handle the new config flags and correctly
compile package basend on that.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
scripts: ext-toolchain: actually probe libc type on config generation
Currently we never call probe_cc before config generation, this cause
the script to never actually detect the correct libc type.
Call probe_cc before config generation to correctl set the .config file.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
scripts: ext-toolchain: add option to overwrite config
It can be useful to overwrite an already generated config.
Option are simply added at the end of the config and make defconfig
will overwrite the relevant option with the new one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
scripts: ext-toolchain: fix wrong prefix in print_config generation
The parsed prefix in print_config is wrong and this produce broken
generated .config that won't work with any external toolchain.
Currently the prefix from a CC of
'arm-openwrt-linux-muslgnueabi-gcc-12.1.0'
produce a prefix
'arm-openwrt-linux-muslgnueabi-gcc-'
This is wrong as the real prefix should be
'arm-openwrt-linux-muslgnueabi-'
This is probably caused by a change in how the toolchain is now handled
that now append also the gcc version. Probably in ancient days the
version wasn't part of the name and the prefix generation stripped the
'-gcc' instead of the gcc version.
Fix this and correctly strip the gcc version and the gcc suffix to
correctly call toolchain bins.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
rules_mk: don't include wrapped bin with external toolchains
Don't add wrapped bin to the TARGET_PATH as it does cause compilation
error.
cmake.mk will use the "command -v" and will use the wrapped bin instead
of the external toolchain bin as they have the same name and command
will select the first result.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Vincent Wiemann [Mon, 28 Dec 2020 15:00:13 +0000 (16:00 +0100)]
rules_mk: use gcc versions for external toolchain
When using the OpenWrt toolchain as an external toolchain the build
failed due to missing LTO support. By choosing the GCC wrappers of
the tools this commit makes sure that the LTO-enabled executables
are being used.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[ wrap the commit description to 72 char ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The change of the PKG_VERSION caused the hash of the package to
change. This is because the PKG_VERSION is present in the
internal directory structure of the archive.
Fixes: e879cccaa215 ("uboot-layerscape: update PKG_HASH") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The interrupt controller in the internal GPIO peripheral will sometimes
generate spurious interrupts. If these are not properly acknowledged, the
system will be held busy until reboot. These spurious interrupts are identified
by the fact that there is no system IRQ number associated, since the interrupt
line was never allocated. Although most prevalent on RTL839x, RTL838x SoCs have
also displayed this behaviour.
UART Console
------------
NWA50AX:
Available below the rubber cover next to the ethernet port.
NWA55AXE:
Available on the board when disassembling the device.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
If the currently installed image is started from Slot A, the device will
flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case
and the device will return to the ZyXEL firmware upon next boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP
-----------------
This installation routine is especially useful in case
* unknown device password (NWA55AXE lacks reset button)
* bricked device
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to owrt.bin
wolfssl: Do not activate HW acceleration on armvirt by default
The armvirt target is also used to run OpenWrt in lxc on other targets
like a Raspberry Pi. If we set WOLFSSL_HAS_CPU_CRYPTO by default the
wolfssl binray is only working when the CPU supports the hardware crypto
extension.
Some targets like the Raspberry Pi do not support the ARM CPU crypto
extension, compile wolfssl without it by default. It is still possible
to activate it in custom builds.
This adds a simple AES-128-CBC encryption/decryption program using
either wolfSSL or OpenSSL as backend to decrypt Arcadyan WG4xx223
configuration partitions. The ipk size is 3,355 bytes.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* Note that the bootloader accepts both encrypted and unencrypted
images, while the stock web interface only accepts encrypted ones.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References in WAX202 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar
* openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts
DTS file for this device.
Netgear encrypted image is used in various devices including WAX202,
WAX206, and EX6400v3. This image format also requires a dummy squashfs4
image which is added here as well.
References in WAX202 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar
* openwrt/bootloader/u-boot-mt7621-2018.09-gitb178829-20200526/board/ralink/common/dual_image.c
Bootloader code that verifies the presence of a squashfs4 image, thus
a dummy image is added here.
* openwrt/tools/imgencoder/src/gj_enc.c
Contains code that generates the encrypted image. There is support for
adding an RSA signature, but it does not look like the signature is
verified by the stock firmware or bootloader.
* openwrt/tools/imgencoder/src/imagekey.h
Contains the encryption key and IV. It appears the same key/IV is used
for other Netgear devices including WAX206 and EX6400v3.
Oleg S [Tue, 19 Jul 2022 12:06:50 +0000 (15:06 +0300)]
ramips: Add support command fw_setsys for Xiaomi routers
The system parameters are contained in the Bdata partition.
To use the fw_setsys command, you need to create a file
fw_sys.config.
This file is created after calling the functions
ubootenv_add_uci_sys_config and ubootenv_add_app_config.
Signed-off-by: Oleg S <remittor@gmail.com>
[ wrapped commit description to 72 char ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
projects / thirdparty / openwrt.git / log
