In nonstatic_find_mem_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In __nonstatic_find_io_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There is a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
[linux@dominikbrodowski.net: Fix typo in commit message] Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
BCM4752 and LNV4752 ACPI nodes describe a Broadcom 4752 GPS module
attached to an UART of the system.
The GPS modules talk a custom protocol which only works with a closed-
source Android gpsd daemon which knows this protocol.
The ACPI nodes also describe GPIOs to turn the GPS on/off these are
handled by the net/rfkill/rfkill-gpio.c code. This handling predates the
addition of enumeration of ACPI instantiated serdevs to the kernel and
was broken by that addition, because the ACPI scan code now no longer
instantiates platform_device-s for these nodes.
Rename the i2c_multi_instantiate_ids HID list to ignore_serial_bus_ids
and add the BCM4752 and LNV4752 HIDs, so that rfkill-gpio gets
a platform_device to bind to again; and so that a tty cdev for gpsd
gets created for these.
Fixes: e361d1f85855 ("ACPI / scan: Fix enumeration for special UART devices") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of failures brcmuart_probe() always returned -ENODEV, this
isn't correct for example platform_get_irq_byname() may return
-EPROBE_DEFER to handle such cases propagate error codes in
brcmuart_probe() in case of failures.
In the file mr75203.c we have a macro named POWER_DELAY_CYCLE_256,
the correct value should be 0x100. The register ip_tmr is expressed
in units of IP clk cycles, in accordance with the datasheet.
Typical power-up delays for Temperature Sensor are 256 cycles i.e. 0x100.
Receiving the Over-Current Protection interrupt while the regulator is
disabled does not count as unhandled/failure (IRQ_NONE, or 0 as it were)
but a "fake event", usually due to inrush as the is regulator about to
be enabled.
Fixes: 390af53e0411 ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Link: https://lore.kernel.org/r/20211224113450.107958-1-marijn.suijten@somainline.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When cross compiling i386_defconfig on an arm64 host with clang, there
are a few instances of '-Waddress-of-packed-member' and
'-Wgnu-variable-sized-type-not-at-end' in arch/x86/boot/compressed/,
which should both be disabled with the cc-disable-warning calls in that
directory's Makefile, which indicates that cc-disable-warning is failing
at the point of testing these flags.
The cc-disable-warning calls fail because at the point that the flags
are tested, KBUILD_CFLAGS has '-march=i386' without $(CLANG_FLAGS),
which has the '--target=' flag to tell clang what architecture it is
targeting. Without the '--target=' flag, the host architecture (arm64)
is used and i386 is not a valid value for '-march=' in that case. This
error can be seen by adding some logging to try-run:
clang-14: error: the clang compiler does not support '-march=i386'
Invoking the compiler has to succeed prior to calling cc-option or
cc-disable-warning in order to accurately test whether or not the flag
is supported; if it doesn't, the requested flag can never be added to
the compiler flags. Move $(CLANG_FLAGS) to the beginning of KBUILD_FLAGS
so that any new flags that might be added in the future can be
accurately tested.
The IBS timers are not stopped properly once BT OFF is triggered.
we could see IBS commands being sent along with version command,
so stopped IBS timers while Bluetooth is off.
Fixes: 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990") Signed-off-by: Panicker Harish <quic_pharish@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
nargs_prop refers to a property located in the reference that is found
within the nargs property. Use the correct reference node in call to
property_entry_read_int_array() to retrieve the correct nargs value.
Fixes: b06184acf751 ("software node: Add software_node_get_reference_args()") Signed-off-by: Clément Léger <clement.leger@bootlin.com> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Daniel Scally <djrscally@gmail.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hardware is capable of controlling any non-contiguous sequence of
LEDs specified in the DT using qcom,enabled-strings as u32
array, and this also follows from the DT-bindings documentation. The
numbers specified in this array represent indices of the LED strings
that are to be enabled and disabled.
Its value is appropriately used to setup and enable string modules, but
completely disregarded in the set_brightness paths which only iterate
over the number of strings linearly.
Take an example where only string 2 is enabled with
qcom,enabled_strings=<2>: this string is appropriately enabled but
subsequent brightness changes would have only touched the zero'th
brightness register because num_strings is 1 here. This is simply
addressed by looking up the string for this index in the enabled_strings
array just like the other codepaths that iterate over num_strings.
Likewise enabled_strings is now also used in the autodetection path for
consistent behaviour: when a list of strings is specified in DT only
those strings will be probed for autodetection, analogous to how the
number of strings that need to be probed is already bound by
qcom,num-strings. After all autodetection uses the set_brightness
helpers to set an initial value, which could otherwise end up changing
brightness on a different set of strings.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3") Fixes: 03b2b5e86986 ("backlight: qcom-wled: Add support for WLED4 peripheral") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211115203459.1634079-10-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The kernel already provides appropriate primitives to perform endianness
conversion which should be used in favour of manual bit-wrangling.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211115203459.1634079-4-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The length of qcom,enabled-strings as property array is enough to
determine the number of strings to be enabled, without needing to set
qcom,num-strings to override the default number of strings when less
than the default (which is also the maximum) is provided in DT.
This also introduces an extra warning when qcom,num-strings is set,
denoting that it is not necessary to set both anymore. It is usually
more concise to set just qcom,num-length when a zero-based, contiguous
range of strings is needed (the majority of the cases), or to only set
qcom,enabled-strings when a specific set of indices is desired.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211115203459.1634079-6-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When not specifying num-strings in the DT the default is used, but +1 is
added to it which turns WLED3 into 4 and WLED4/5 into 5 strings instead
of 3 and 4 respectively, causing out-of-bounds reads and register
read/writes. This +1 exists for a deficiency in the DT parsing code,
and is simply omitted entirely - solving this oob issue - by parsing the
property separately much like qcom,enabled-strings.
This also enables more stringent checks on the maximum value when
qcom,enabled-strings is provided in the DT, by parsing num-strings after
enabled-strings to allow it to check against (and in a subsequent patch
override) the length of enabled-strings: it is invalid to set
num-strings higher than that.
The DT currently utilizes it to get around an incorrect fixed read of
four elements from that array (has been addressed in a prior patch) by
setting a lower num-strings where desired.
Fixes: 93c64f1ea1e8 ("leds: add Qualcomm PM8941 WLED driver") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211115203459.1634079-5-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
of_property_read_u32_array takes the number of elements to read as last
argument. This does not always need to be 4 (sizeof(u32)) but should
instead be the size of the array in DT as read just above with
of_property_count_elems_of_size.
To not make such an error go unnoticed again the driver now bails
accordingly when of_property_read_u32_array returns an error.
Surprisingly the indentation of newlined arguments is lining up again
after prepending `rc = `.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211115203459.1634079-3-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The strings passed in DT may possibly cause out-of-bounds register
accesses and should be validated before use.
Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211115203459.1634079-2-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The output of bpftool prog tracelog is currently buffered, which is
inconvenient when piping the output into other commands. A simple
tracelog | grep will typically not display anything. This patch fixes it
by enabling line buffering on stdout for the whole bpftool binary.
Fixes: 30da46b5dc3a ("tools: bpftool: add a command to dump the trace pipe") Signed-off-by: Quentin Monnet <quentin@isovalent.com> Signed-off-by: Paul Chaignon <paul@isovalent.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20211220214528.GA11706@Mem Signed-off-by: Sasha Levin <sashal@kernel.org>
If user has a set to use SOCK_STREAM the socket would default to
L2CAP_MODE_ERTM which later needs to be adjusted if the destination
address is LE which doesn't support such mode.
Fixes: 15f02b9105625 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When creating an external event, the current time needs to
be propagated to other participants of a simulation. This
is done in the places here where we kick a virtq etc.
However, it must be done for _all_ external events, and
that includes making the initial socket connection and
later closing it. Call time_travel_propagate_time() to do
this before making or closing the socket connection.
Apparently, at least for the initial connection creation,
due to the remote side in my use cases using microseconds
(rather than nanoseconds), this wasn't a problem yet; only
started failing between 5.14-rc1 and 5.15-rc1 (didn't test
others much), or possibly depending on the configuration,
where more delays happen before the virtio devices are
initialized.
Fixes: 88ce64249233 ("um: Implement time-travel=ext") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
On 32-bit, the first entry might be at 0/NULL, but that's
strange and leads to issues, e.g. where we check "if (ret)".
Use a IOREMAP_BIAS/IOREMAP_MASK of 0x80000000UL to avoid
this. This then requires reducing the number of areas (via
MAX_AREAS), but we still have 128 areas, which is enough.
Fixes: ca2e334232b6 ("lib: add iomem emulation (logic_iomem)") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a 32-bit build, the (unsigned long long) casts throw warnings
(or errors) due to being to a different integer size. Cast to
uintptr_t first (with the __force for sparse) and then further
to get the consistent print on 32 and 64-bit.
Fixes: ca2e334232b6 ("lib: add iomem emulation (logic_iomem)") Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rename set_signals() as there's at least one driver that
uses the same name and can now be built on UM due to PCI
support, and thus we can get symbol conflicts.
Also rename set_signals_trace() to be consistent.
Reported-by: kernel test robot <lkp@intel.com> Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Many places in the kernel use 'udelay' as an identifier, and
are broken with the current "#define udelay um_udelay". Fix
this by adding an argument to the macro, and do the same to
'ndelay' as well, just in case.
Fixes: 0bc8fb4dda2b ("um: Implement ndelay/udelay in time-travel mode") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
One device_add is called disk->ev will be freed by disk_release, so we
should free it twice. Fix this by allocating disk->ev after device_add
so that the extra local unwinding can be removed entirely.
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoC") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20211217202717.10041-3-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: e4bf1b0970ef ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20211217202717.10041-2-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 6GHz passive scan is performed only once every 50 minutes.
However, in case of suspend/resume, the regulatory information
is reset, so 6GHz channels may become disabled.
Fix it by performing a 6GHz passive scan within 60 seconds after
suspend/resume even if the 50 minutes timeout did not expire yet.
In some cases the sta is being removed twice since we do not test the
roc aux running before removing it. Start looking at the bit before
removing the sta.
On a 32-bit build, the division here needs to be done
using do_div(), otherwise the compiler will try to call
a function that doesn't exist, thus failing to build.
Many Intel based platforms face system random freeze after commit 9e2fd29864c5 ("rtw88: add napi support").
The commit itself shouldn't be the culprit. My guess is that the 8821CE
only leaves ASPM L1 for a short period when IRQ is raised. Since IRQ is
masked during NAPI polling, the PCIe link stays at L1 and makes RX DMA
extremely slow. Eventually the RX ring becomes messed up:
[ 1133.194697] rtw_8821ce 0000:02:00.0: pci bus timeout, check dma status
Since the 8821CE hardware may fail to leave ASPM L1, manually do it in
the driver to resolve the issue.
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3bcd ("wilc1000: use goto labels on error path") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211217150311.GC16611@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
offload_flags have to be dropped for mt7921 because mt76.omac_idx 0 would
always run as station mode that would cause Tx encapsulation setting
is not applied to mac80211.
Also, drop IEEE80211_OFFLOAD_ENCAP_4ADDR too because it is not really
being supported.
Fixes: e0f9fdda81bd ("mt76: mt7921: add ieee80211_ops") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
CN9130 has a built-in CP115 which has 2 GPIO controllers, but unlike in
Armada 7k and 8k both are left disabled by the SoC DTSI.
This first of all makes no sense as they are always present due to being
SoC built-in and its an issue as boards like CN9130-CRB use the CPO GPIO2
pins for regulators and SD card support without enabling them first.
So, enable both of them like Armada 7k and 8k do.
Fixes: 6b8970bd8d7a ("arm64: dts: marvell: Add support for Marvell CN9130 SoC support") Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CN9130 has one CP115 built in, which like the CP110 has 2 GPIO and 2 SPI
controllers built-in.
However, unlike the Armada 7k and 8k the SoC DTSI doesn't add the required
aliases as both the Orion SPI driver and MVEBU GPIO drivers require the
aliases to be present.
So add the required aliases for GPIO and SPI controllers.
Fixes: 6b8970bd8d7a ("arm64: dts: marvell: Add support for Marvell CN9130 SoC support") Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the decompressor's head.S we need to start with an instruction that
is some kind of NOP, but also mimics as the PE/COFF header, when the
kernel is linked as an UEFI application. The clever solution here is
"tstne r0, #0x4d000", which in the worst case just clobbers the
condition flags, and bears the magic "MZ" signature in the lowest 16 bits.
However the encoding used (0x13105a4d) is actually not valid, since bits
[15:12] are supposed to be 0 (written as "(0)" in the ARM ARM).
Violating this is UNPREDICTABLE, and *can* trigger an UNDEFINED
exception. Common Cortex cores seem to ignore those bits, but QEMU
chooses to trap, so the code goes fishing because of a missing exception
handler at this point. We are just saved by the fact that commonly (with
-kernel or when running from U-Boot) the "Z" bit is set, so the
instruction is never executed. See [0] for more details.
To make things more robust and avoid UNPREDICTABLE behaviour in the
kernel code, lets replace this with a "two-instruction NOP":
The first instruction is an exclusive OR, the effect of which the second
instruction reverts. This does not leave any trace, neither in a
register nor in the condition flags. Also it's a perfectly valid
encoding. Kudos to Peter Maydell for coming up with this gem.
If clocks for some reason couldn't be enabled, probe function returns
immediately, without disabling PM. This obviously leaves PM ref counters
unbalanced.
Fix that by jumping to appropriate error path, so effects of PM functions
are reversed.
Upon failure, dma_alloc_coherent() returns NULL. If that does happen,
passing some uninitialised stack contents to dma_mapping_error() - which
belongs to a different API in the first place - has precious little
chance of detecting it.
Also include the correct header, because the fragile transitive
inclusion currently providing it is going to break soon.
Fixes: 20e7dce255e9 ("drm/tegra: Remove memory allocation from Falcon library") CC: Thierry Reding <thierry.reding@gmail.com> CC: Mikko Perttunen <mperttunen@nvidia.com> CC: dri-devel@lists.freedesktop.org Signed-off-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As of commit 4782c0a5dd88 ("clk: tegra: Don't deassert reset on enabling
clocks"), module resets are no longer automatically deasserted when the
module clock is enabled. To make sure that the gr2d module continues to
work, we need to explicitly control the module reset.
Set the maximum register to 0xff so we can dump the registers for this
device in debugfs.
Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver") Cc: Rob Clark <robdclark@chromium.org> Cc: Douglas Anderson <dianders@chromium.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211215002529.382383-1-swboyd@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently Soundcard has 1 rx device for headset and SoundWire Speaker Playback.
This setup has issues, ex if we try to play on headset the audio stream is
also sent to SoundWire Speakers and we will hear sound in both headsets and speakers.
Make a separate device for Speakers and Headset so that the streams are
different and handled properly.
In ath11k_mac_op_hw_scan(), the return value of kzalloc() is directly
used in memcpy(), which may lead to a NULL pointer dereference on
failure of kzalloc().
Fix this bug by adding a check of arg.extraie.ptr.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_ATH11K=m show no new warnings, and our static
analyzer no longer warns about this code.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211202155348.71315-1-zhou1615@umn.edu Signed-off-by: Sasha Levin <sashal@kernel.org>
In msi001_probe(), if the creation of control for bandwidth_auto
fails, there will be a null-ptr-deref issue when it is used in
v4l2_ctrl_auto_cluster().
Check dev->hdl.error before v4l2_ctrl_auto_cluster() to fix this bug.
Link: https://lore.kernel.org/linux-media/20211026112348.2878040-1-wanghai38@huawei.com Fixes: 93203dd6c7c4 ("[media] msi001: Mirics MSi001 silicon tuner driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dvb_usb_device_init stores parts of properties at d->props
and d->desc and uses it on dvb_usb_device_exit.
Free of properties on module probe leads to use after free.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204597
The patch makes properties static instead of allocated on heap to prevent
memleak and use after free.
Also fixes s421_properties.devices initialization to have 2 element
instead of 6 copied from p7500_properties.
[mchehab: fix function call alignments] Link: https://lore.kernel.org/linux-media/20190822104147.4420-1-vasilyev@ispras.ru Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru> Fixes: 299c7007e936 ("media: dw2102: Fix memleak on sequence of probes") Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Attempting to migrate the PMU context after we've unregistered the PMU
device, or especially if we never successfully registered it in the
first place, is a woefully bad idea. It's also fundamentally pointless
anyway. Make sure to unregister an instance from the hotplug handler
*without* invoking the teardown callback.
Steven Maddox reported in the OpenWrt bugzilla, that his
RaidSonic IB-NAS4220-B was no longer booting with the new
OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was
working with the previous OpenWrt 19.07 series (uses 4.14).
|[ 5.548038] No RedBoot partition table detected in 30000000.flash
|[ 5.618553] Searching for RedBoot partition table in 30000000.flash at offset 0x0
|[ 5.739093] No RedBoot partition table detected in 30000000.flash
|...
|[ 7.039504] Waiting for root device /dev/mtdblock3...
The provided bootlog shows that the RedBoot partition parser was
looking for the partition table "at offset 0x0". Which is strange
since the comment in the device-tree says it should be at 0xfe0000.
Further digging on the internet led to a review site that took
some useful PCB pictures of their review unit back in February 2009.
Their picture shows a Spansion S29GL128N11TFI01 flash chip.
>From Spansion's Datasheet:
"S29GL128N: One hundred twenty-eight 64 Kword (128 Kbyte) sectors"
Steven also provided a "cat /sys/class/mtd/mtd0/erasesize" from his
unit: "131072".
With the 128 KiB Sector/Erasesize in mind. This patch changes the
fis-index-block property to (0xfe0000 / 0x20000) = 0x7f.
Fixes: b5a923f8c739 ("ARM: dts: gemini: Switch to redboot partition parsing") Reported-by: Steven Maddox <s.maddox@lantizia.me.uk> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Steven Maddox <s.maddox@lantizia.me.uk> Link: https://lore.kernel.org/r/20211206004334.4169408-1-linus.walleij@linaro.org'
Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137 Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
* @cs_setup: delay to be introduced by the controller after CS is
asserted
The cs_setup delay needs to happen *after* CS is asserted, that is, at
the end of spi_set_cs, not at the beginning. Otherwise we're just
delaying before the SPI transaction starts at all, which isn't very
useful.
No drivers use this right now, but that is likely to change soon with an
upcoming Apple SPI HID transport driver.
Fixes: 25093bdeb6bc ("spi: implement SW control for CS times") Signed-off-by: Hector Martin <marcan@marcan.st> Link: https://lore.kernel.org/r/20211210170534.177139-1-marcan@marcan.st Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
frag_timer will be created & initialized for stations when
they associate and will be deleted during every key installation
while flushing old fragments.
For AP interface self peer will be created and Group keys
will be installed for this peer, but there will be no real
Station entry & hence frag_timer won't be created and
initialized, deleting such uninitialized kernel timers causes below
warnings and backtraces printed with CONFIG_DEBUG_OBJECTS_TIMERS
enabled.
When hisi_qm_resume() returns 0, it indicates that the device has started
successfully. If the device fails to start, hisi_qm_resume() needs to
return the actual error code to the caller instead of 0.
We should not call pm_runtime_resume_and_get where the reference
count is expected to be incremented unconditionally. This patch
reverts these calls to the original unconditional get_sync call.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com> Fixes: 747bf30fd944 ("crypto: stm32/cryp - Fix PM reference leak...") Fixes: 1cb3ad701970 ("crypto: stm32/hash - Fix PM reference leak...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Extra crypto manager auto test were crashing or failling due
to 2 reasons:
- block in a dead loop (dues to issues in cipher end process management)
- crash due to read/write unmapped memory (this crash was also reported
when using openssl afalg engine)
Rework interrupt management, interrupts are masked as soon as they are
no more used: if input buffer is fully consumed, "Input FIFO not full"
interrupt is masked and if output buffer is full, "Output FIFO not
empty" interrupt is masked.
And crypto request finish when input *and* outpout buffer are fully
read/write.
About the crash due to unmapped memory, using scatterwalk_copychunks()
that will map and copy each block fix the issue.
Using this api and copying full block will also fix unaligned data
access, avoid early copy of in/out buffer, and make useless the extra
alignment constraint.
Fixes: 9e054ec21ef8 ("crypto: stm32 - Support for STM32 CRYP crypto module") Reported-by: Marek Vasut <marex@denx.de> Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the lrw autotest if lrw uses the CRYP as the AES block cipher
provider (as ecb(aes)). At end of request, CRYP should not update the IV
in case of ECB chaining mode. Indeed the ECB chaining mode never uses
the IV, but the software LRW chaining mode uses the IV field as
a counter and due to the (unexpected) update done by CRYP while the AES
block process, the counter get a wrong value when the IV overflow.
Fixes: 5f49f18d27cd ("crypto: stm32/cryp - update to return iv_out") Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some auto tests failed because driver wasn't returning the expected
error with some input size/iv value/tag size.
Now:
Return 0 early for empty buffer. (We don't need to start the engine for
an empty input buffer).
Accept any valid authsize for gcm(aes).
Return -EINVAL if iv for ccm(aes) is invalid.
Return -EINVAL if buffer size is a not a multiple of algorithm block size.
Fixes: 9e054ec21ef8 ("crypto: stm32 - Support for STM32 CRYP crypto module") Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't erase key:
If key is erased before the crypto_finalize_.*_request() call, some
pending process will run with a key={ 0 }.
Moreover if the key is reset at end of request, it breaks xts chaining
mode, as for last xts block (in case input len is not a multiple of
block) a new AES request is started without calling again set_key().
Fixes: 9e054ec21ef8 ("crypto: stm32 - Support for STM32 CRYP crypto module") Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
STM32 CRYP hardware doesn't manage CTR counter bigger than max U32, as
a workaround, at each block the current IV is saved, if the saved IV
lower u32 is 0xFFFFFFFF, the full IV is manually incremented, and set
in hardware. Fixes: bbb2832620ac ("crypto: stm32 - Fix sparse warnings") Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Test can fail either immediately when ASSERT() failed or at the
end if one or more EXPECT() was not met. The exact return code
is decided based on the number of successful ASSERT()s.
If test has no ASSERT()s, however, the return code will be 0,
as if the test did not fail. Start counting ASSERT()s from 1.
Fixes: 369130b63178 ("selftests: Enhance kselftest_harness.h to print which assert failed") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable into the case that uses it, which silences the warning:
./arch/x86/include/asm/uaccess.h:317:23: warning: statement will never be executed [-Wswitch-unreachable]
317 | unsigned char x_u8__; \
| ^~~~~~
copy_user_offload() will actually push a struct struct xfrm_user_offload,
which is different than (struct xfrm_state *)->xso
(struct xfrm_state_offload)
mwifiex_dequeue_tx_packet()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 1432 (Lock A)
mwifiex_send_addba()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 608 (Lock B)
mwifiex_process_sta_tx_pause()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 398 (Lock B)
mwifiex_update_ralist_tx_pause()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 941 (Lock A)
Similar report for mwifiex_process_uap_tx_pause().
While the locking expectations in this driver are a bit unclear, the
Fixed commit only intended to protect the sta_ptr, so we can drop the
lock as soon as we're done with it.
IIUC, this deadlock cannot actually happen, because command event
processing (which calls mwifiex_process_sta_tx_pause()) is
sequentialized with TX packet processing (e.g.,
mwifiex_dequeue_tx_packet()) via the main loop (mwifiex_main_process()).
But it's good not to leave this potential issue lurking.
Commit 739b4e7756d3 ("drm/msm/dsi: Fix an error code in
msm_dsi_modeset_init()") changed msm_dsi_modeset_init() to return an
error code in case msm_dsi_manager_validate_current_config() returns
false. However this is not an error case, but a slave DSI of the bonded
DSI link. In this case msm_dsi_modeset_init() should return 0, but just
skip connector and bridge initialization.
To reduce possible confusion, drop the
msm_dsi_manager_validate_current_config() function, and specif 'bonded
&& !master' condition directly in the msm_dsi_modeset_init().
Fixes: 739b4e7756d3 ("drm/msm/dsi: Fix an error code in msm_dsi_modeset_init()") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Link: https://lore.kernel.org/r/20211125180114.561278-1-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Expedited RCU grace periods invoke sync_rcu_exp_select_node_cpus(), which
takes two passes over the leaf rcu_node structure's CPUs. The first
pass gathers up the current CPU and CPUs that are in dynticks idle mode.
The workqueue will report a quiescent state on their behalf later.
The second pass sends IPIs to the rest of the CPUs, but excludes the
current CPU, incorrectly assuming it has been included in the first
pass's list of CPUs.
Unfortunately the current CPU may have changed between the first and
second pass, due to the fact that the various rcu_node structures'
->lock fields have been dropped, thus momentarily enabling preemption.
This means that if the second pass's CPU was not on the first pass's
list, it will be ignored completely. There will be no IPI sent to
it, and there will be no reporting of quiescent states on its behalf.
Unfortunately, the expedited grace period will nevertheless be waiting
for that CPU to report a quiescent state, but with that CPU having no
reason to believe that such a report is needed.
The result will be an expedited grace period stall.
Fix this by no longer excluding the current CPU from consideration during
the second pass.
[...]
x86_64-linux-gnu-ld: drivers/gpu/drm/msm/dp/dp_catalog.o: in function `dp_catalog_ctrl_config_msa':
dp_catalog.c:(.text+0x57e): undefined reference to `rational_best_approximation'
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support") Reported-by: kernelbot <kernel-bot@kylinos.cn> Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Link: https://lore.kernel.org/r/20211110070950.3355597-2-liu.yun@linux.dev Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Elsewhere we treat zero as "no fence" and __msm_gem_submit_destroy()
skips removal from fence_idr. We could alternately change this to use
negative values for "no fence" but I think it is more clear to not allow
zero as a valid fence_id.
Signed-off-by: Rob Clark <robdclark@chromium.org> Fixes: a61acbbe9cf8 ("drm/msm: Track "seqno" fences by idr") Link: https://lore.kernel.org/r/20211129182344.292609-1-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
During dcn31_stream_encoder_create, if PHYC/D get remapped to F/G on B0
then we'll index 5 or 6 into a array of length 5 - leading to an
access violation on some configs during device creation.
[How]
Software won't be touching PHYF/PHYG directly, so just extend the
array to cover all possible engine IDs.
Even if it does by try to access one of these registers by accident
the offset will be 0 and we'll get a warning during the access.
Fixes: 2fe9a0e1173f ("drm/amd/display: Fix DCN3 B0 DP Alt Mapping") Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
crc_rd_wrk shouldn't be null in crc_win_update_set(). Current programming
logic is inconsistent in crc_win_update_set().
[How]
Initially, return if crc_rd_wrk is NULL. Later on, we can use member of
crc_rd_wrk safely.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 9a65df193108 ("drm/amd/display: Use PSP TA to read out crc") Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For Mediatek chipset, it can not enabled if there are something wrong
in btmtk_setup_firmware_79xx(). Thus, the process must be terminated
and returned error code.
Fixes: fc342c4dc4087 ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch refactors the set_exp_feature with a feature table
consisting of UUIDs and the corresponding callback functions.
In this way, a new experimental feature setting function can be
simply added with its UUID and callback function.
Signed-off-by: Joseph Hwang <josephsih@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On an imx6dl-pico-pi board with a QCA9377 SDIO chip, simply trying to
connect via ssh to another machine causes:
[ 55.824159] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.832169] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.838529] ath10k_sdio mmc1:0001:1: failed to push frame: -12
[ 55.905863] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.913650] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.919887] ath10k_sdio mmc1:0001:1: failed to push frame: -12
, leading to an ssh connection failure.
One user inspected the size of frames on Wireshark and reported
the followig:
"I was able to narrow the issue down to the mtu. If I set the mtu for
the wlan0 device to 1486 instead of 1500, the issue does not happen.
The size of frames that I see on Wireshark is exactly 1500 after
setting it to 1486."
Clearing the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE avoids the problem and
the ssh command works successfully after that.
Introduce a 'credit_size_workaround' field to ath10k_hw_params for
the QCA9377 SDIO, so that the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE
is not set in this case.
Tested with QCA9377 SDIO with firmware WLAN.TF.1.1.1-00061-QCATFSWPZ-1.
Fixes: 2f918ea98606 ("ath10k: enable alt data of TX path for sdio") Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211124131047.713756-1-festevam@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
When rt_runtime is modified from -1 to a valid control value, it may
cause the task to be throttled all the time. Operations like the following
will trigger the bug. E.g:
1. echo -1 > /proc/sys/kernel/sched_rt_runtime_us
2. Run a FIFO task named A that executes while(1)
3. echo 950000 > /proc/sys/kernel/sched_rt_runtime_us
When rt_runtime is -1, The rt period timer will not be activated when task
A enqueued. And then the task will be throttled after setting rt_runtime to
950,000. The task will always be throttled because the rt period timer is
not activated.
Fixes: d0b27fa77854 ("sched: rt-group: synchonised bandwidth period") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Li Hua <hucool.lihua@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20211203033618.11895-1-hucool.lihua@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In iwl_txq_dyn_alloc_dma, txq->tfds is freed at first time by:
iwl_txq_alloc()->goto err_free_tfds->dma_free_coherent(). But
it forgot to set txq->tfds to NULL.
Then the txq->tfds is freed again in iwl_txq_dyn_alloc_dma by:
goto error->iwl_txq_gen2_free_memory()->dma_free_coherent().
My patch sets txq->tfds to NULL after the first free to avoid the
double free.
Fixes: 0cd1ad2d7fd41 ("iwlwifi: move all bus-independent TX functions to common code") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Link: https://lore.kernel.org/r/20210403054755.4781-1-lyl2019@mail.ustc.edu.cn Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit e955f959ac52 ("media: si2157: Better check for running tuner in
init") completely broke the "warm" tuner detection of the si2157 driver
due to a simple endian error: The Si2157 CRYSTAL_TRIM property code is
0x0402 and needs to be transmitted LSB first. However, it was inserted
MSB first, causing the warm detection to always fail and spam the kernel
log with tuner initialization messages each time the DVB frontend
device was closed and reopened:
[ 312.215682] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 312.264334] si2157 16-0060: firmware version: 3.0.5
[ 342.248593] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 342.295743] si2157 16-0060: firmware version: 3.0.5
[ 372.328574] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 372.385035] si2157 16-0060: firmware version: 3.0.5
Also, the reinitializations were observed disturb _other_ tuners on
multi-tuner cards such as the Hauppauge WinTV-QuadHD, leading to missed
or errored packets when one of the other DVB frontend devices on that
card was opened.
Fix the order of the property code bytes to make the warm detection work
again, also reducing the tuner initialization message in the kernel log
to once per power-on, as well as fixing the interference with other
tuners.
In mxb_attach(dev, info), saa7146_vv_init() is called to allocate a
new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of mxb_probe(dev). There is a dereference of dev->vv_data
in saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_MXB=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 03b1930efd3c ("V4L/DVB: saa7146: fix regression of the av7110/budget-av driver") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dib8000_init(), the variable fe is not freed or passed out on the
failure of dib8000_identify(&state->i2c), which could lead to a memleak.
Fix this bug by adding a kfree of fe in the error path.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DVB_DIB8000=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 77e2c0f5d471 ("V4L/DVB (12900): DiB8000: added support for DiBcom ISDB-T/ISDB-Tsb demodulator DiB8000") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Those are harmless, but avoidable when guarding it with ifdef.
I could guard push/pop as well, but this would require one more
ifdef cruft around a single line which I don't think is reasonable.
Clang (13) doesn't get the jokes about specifying libraries to link in
cclags of individual .o objects:
clang-13: warning: -lm: 'linker' input unused [-Wunused-command-line-argument]
[ ... ]
LD samples/bpf/xdp_redirect_cpu
LD samples/bpf/xdp_redirect_map_multi
LD samples/bpf/xdp_redirect_map
LD samples/bpf/xdp_redirect
LD samples/bpf/xdp_monitor
/usr/bin/ld: samples/bpf/xdp_sample_user.o: in function `sample_summary_print':
xdp_sample_user.c:(.text+0x84c): undefined reference to `floor'
/usr/bin/ld: xdp_sample_user.c:(.text+0x870): undefined reference to `ceil'
/usr/bin/ld: xdp_sample_user.c:(.text+0x8cf): undefined reference to `floor'
/usr/bin/ld: xdp_sample_user.c:(.text+0x8f3): undefined reference to `ceil'
[ more ]
Specify '-lm' as ldflags for all xdp_sample_user.o users in the main
Makefile and remove it from ccflags of ^ in Makefile.target -- just
like it's done for all other samples. This works with all compilers.
Remove xdp_samples_user.o rule redefinition which generates Makefile
warning and instead override TPROGS_CFLAGS. This seems to work fine when
building inside selftests/bpf.
That was one big head-scratcher before I found that generic
Makefile.target hid this surprising specialization for for xdp_samples_user.o.
Main change is to use actual locally installed libbpf headers.
Also drop printk macro re-definition (not even used!).
API headers from libbpf should not be accessed directly from the source
directory. Instead, they should be exported with "make install_headers".
Make sure that samples/bpf/Makefile installs the headers properly when
building.
The object compiled from and exported by libbpf are now placed into a
subdirectory of sample/bpf/ instead of remaining in tools/lib/bpf/. We
attempt to remove this directory on "make clean". However, the "clean"
target re-enters the samples/bpf/ directory from the root of the
repository ("$(MAKE) -C ../../ M=$(CURDIR) clean"), in such a way that
$(srctree) and $(src) are not defined, making it impossible to use
$(LIBBPF_OUTPUT) and $(LIBBPF_DESTDIR) in the recipe. So we only attempt
to clean $(CURDIR)/libbpf, which is the default value.
Add a dependency on libbpf's headers for the $(TRACE_HELPERS).
We also change the output directory for bpftool, to place the generated
objects under samples/bpf/bpftool/ instead of building in bpftool's
directory directly. Doing so, we make sure bpftool reuses the libbpf
library previously compiled and installed.
Currently, mte_set_mem_tag_range() and mte_zero_clear_page_tags() use
DC {GVA,GZVA} unconditionally. But, they should make sure that
DCZID_EL0.DZP, which indicates whether or not use of those instructions
is prohibited, is zero when using those instructions.
Use ST{G,ZG,Z2G} instead when DCZID_EL0.DZP == 1.
projects / thirdparty / kernel / stable.git / log
