Marek Behún [Sat, 26 Sep 2020 21:42:52 +0000 (21:42 +0000)]
perf: fix building with musl when NLS is enabled
This package fails with a strange error when building with musl when NLS
is enabled. The configuration thinks that libelf is not present, even
though DEPENDS contains +libelf, because when NLS is enabled, libelf.so
depends on libintl, and the correct LDFLAGS are missing for
libintl-full. This then causes the configuration script to check for
glibc, but this fails because we are using musl.
bcm63xx: add a few DTSI files to share definitions
After the LED labels have been made more general by removing
the model names, we can move several definitions to DTSI files
to reduce the amount of duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for various targets, this will remove
the "devicename" from LED labels in bcm63xx, as it's useless and
only creates complexity.
The devicename is removed in DTS files and 01_leds, merging
several cases on the way. A migration script is added for
existing configurations.
Note that a few labels were using "model::function" scheme without
color specified, those were converting to just "function" and the
necessary migrations were added to the migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Fri, 9 Oct 2020 22:16:53 +0000 (23:16 +0100)]
kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since "sda-gpios" and "scl-gpios" are only available since kernel 4.19,
a few devices have redundantly defined "gpios" to also support older
kernels. Since we have nothing older than 4.19 now, we can remove
the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Robert Marko [Wed, 7 Oct 2020 15:12:56 +0000 (17:12 +0200)]
ipq40xx: 5.4: move AR40xx driver into files
There is no point in keeping the AR40xx driver as a patch as its
not pending merge or backport.
To allow for easier maintenance until DSA is ready move it into
files like EDMA is.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[combine with removal from patches-5.4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Sun, 5 Feb 2017 16:55:53 +0000 (17:55 +0100)]
rt2x00: mt7620: differentiate based on SoC's CHIP_VER
The vendor driver does things differently based on what it finds in the
SoC's CHIP_VER register, which should tell whether this is MT7620N or
MT7620A (PKG) and probably also the revision (VER) and most likely
also something about the silicon implementer (ECO).
Introduce codepaths just like the ones in the vendor driver to handle
the different chips properly.
Some of those paths are most likely dead code and left-overs from FPGA
versions or early prototypes of the chip. It'd thus be great if people
can post their kernel logs, at least the line telling the chip version
and eco, so we know what's actually out there in the wild -- all I
could find is
[ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6
and
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
which would make things easier, as then we really just need to know
whether it's MT7620N or MT7620A and not care about FPGA or prototypes
with ver <= 1 and eco <= 2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Mon, 5 Oct 2020 23:54:43 +0000 (13:54 -1000)]
kernel: clean up XATTR config symbols
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sven Roederer [Sun, 27 Sep 2020 21:07:38 +0000 (23:07 +0200)]
build, imagebuilder: Do not require compilers
The buildroot and SDK both require the compilers (gcc, g++) to be
installed on the host system, however the ImageBuilder uses precompiled
binaries.
This patch changes the prerequirements checks to skip the checking for
the compilers if running as ImageBuilder. A similar change has been
made for libncurses-dev in 4a1a58a3e2d2.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de> Acked-by: Paul Spooren <mail@aparcar.org>
Like in the previous patches for other targets, this will remove
the "devicename" from LED labels in lantiq.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated. The DTS/DTSI consolidation is
only performed for files-5.4.
For lantiq,easy98020 some LED definitions have the form
"devicename:function" without the color, so we need to implement
explicit migration for that one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1
Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite
them with local versions so far.
Remove the local files and use patches to be closer to upstream.
We already do the same for IPQ40xx/AP-DK01.1-C1.
Technically, this changes the compatible from "qcom,ipq4019" to
"qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly
beforehand anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Fri, 18 Sep 2020 13:31:59 +0000 (22:31 +0900)]
ipq40xx: improve support for Edgecore ECW5211
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:
* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe
Fixes: 4488b260a02e ("ipq40xx: add Edgecore ECW5211 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> Acked-by: Robert Marko <robert.marko@sartura.hr>
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq40xx.
The devicename is removed in DTS files and 01_leds, and a migration
script is added. While at it, also harmonize capitalization of
wlan2G/wlan5G vs. wlan2g/wlan5g.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Jo-Philipp Wich [Sun, 4 Oct 2020 21:04:51 +0000 (23:04 +0200)]
uhttpd: update to latest Git HEAD
14a3cb4 ubus: fix legacy empty reply format 0f38b03 client: fix spurious keepalive connection timeouts 88ba2fa client: really close connection on timeout c186212 ubus: support GET method with CORS requests
Joe Mullally [Sat, 12 Sep 2020 18:46:28 +0000 (19:46 +0100)]
ath79: add support for TP-Link TL-WPA8630P (EU) v2.1
This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1
version. The only unique aspect for the firmware compared to v2
layout is the partition layout.
Note that while the EU version has different partitioning for
v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image.
If you plan to use this device, make sure you have a look at
the Wiki page to check whether the device is supported and
which image needs to be taken.
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Notes
-----
The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave
this empty as well. It is complicated enough already ...
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[improve partitions, use v2 DTSI, add entry in 02_network, rewrite
and extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Andre Heider [Fri, 4 Sep 2020 07:30:49 +0000 (09:30 +0200)]
omap: update uboot to v2020.04
Fixes the build error:
/usr/bin/ld: scripts/dtc/dtc-parser.tab.o:(.bss+0x10): multiple definition of `yylloc'; scripts/dtc/dtc-lexer.lex.o:(.bss+0x0): first defined here
collect2: error: ld returned 1 exit status
00a84c5 linux-firmware: Update AMD SEV firmware 71338c2 Merge branch 'for-master' of https://github.com/CosmicPenguin/linux-firmware into main 07367b9 linux-firmware: Update firmware file for Intel Bluetooth AX200 1d1586a linux-firmware: Update firmware file for Intel Bluetooth AX201 28b333d linux-firmware: Update firmware file for Intel Bluetooth 9560 db30380 linux-firmware: Update firmware file for Intel Bluetooth 9260 eb3aa1f Mellanox: Add new mlxsw_spectrum firmware xx.2008.1310 ec88f05 mediatek: update MT7915 firmware to 20200819 a9993f8 brcm: Fix a stale symlink for RPi3 model b+ f48fec4 qcom: Add updated a5xx and a6xx microcode d5f9eea wl18xx: update firmware file 8.9.0.0.83 7a237c6 linux-firmware: mt7615: update firmware to 20200814 version 74bd44f amdgpu: add navi12 firmware from 20.30 b9f69cd amdgpu: update navi10 firmware for 20.30
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pawel Dembicki [Tue, 25 Aug 2020 13:26:05 +0000 (15:26 +0200)]
layerscape: add layerscape's SATA driver package
This patch intruduce SATA support for layerscape devices.
Target specific package with ahci_qoriq driver was added
to local modules.mk.
Kmod package was added to default packages for devices with
SATA interface.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
While we mostly use the ucidef_set_led_* functions directly in 01_leds
we still have the set_wifi_led function in parallel for several old
devices. This is not only inconsistent with the other definitions,
it also links to the wlan0 interface instead of using a phy trigger
which would be independent of the interface name (and is used for
all newer devices anyway). Apart from that, the standard names
"wifi" and "wifi-led" are not very helpful in a world with different
radio bands either.
Thus, this patch removes the set_wifi_led function and puts the
relevant commands into the cases explicitly. This makes the
mechanism used more evident and will hopefully lead to some future
improvements or at least prevent some copy-pasting of the old
setups.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.
For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
base-files: allow exceptions when removing devicename from LEDs
Without the model-based devicename for LEDs, there are still cases
where a third component is required, typically when it refers to
internal "devices" like phys etc. An example are the following two
found on ramips:
- rt2800soc-phy0::radio
- rt2800pci-phy0::radio
So far, the rt2800*-phy: prefixes would be removed by the devicename
removal ("migration") script, and the configuration for these LEDs
would be broken.
To address this, this patch allows to add arguments to a call of
remove_devicename_leds, which will be compared against the first
part of the LED names/labels, and then be ignored by the routine,
and thus not removed:
This mechanism is supposed to be used when a "devicename" applies
to several devices. If only a single device is affected, it might
be more effective to use a case statement and exclude the device
from migration by that entirely.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
base-files: add function to remove devicename from LED labels
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. In patches
subsequent to this one, we will thus remove the modelname from
the label definitions on various targets.
To migrate the existing definitions from older installations,
a migration script needs to be deployed that does
modelname:color:function -> color:function
e.g.
dir-789:green:status -> green:status
This patch introduces two functions that do exactly that:
For each entry in /etc/config/system, the routine will check whether
two (or more) colons are present, and then remove everything up to
(and including) the first colon.
For now, this will be applied unconditionally, i.e. if the function
is called for a device, all labels will be cut like this.
However, for a future case of mixed three-part and two-part labels,
it should not be too hard to provide a function argument with
exceptions to the removal.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
lantiq: move dts-v1 statement to top-level DTSI files
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In lantiq, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent SoC-based DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.
Changes are applied to files-5.4 only, files-4.19 remains untouched.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
reg accesses on integrated ar8229 sometimes fails. As a result, phy read
got incorrect port status and wan link goes down and up mysteriously.
After comparing ar8216 with the old driver, these local_irq_save/restore
calls are the only meaningful differences I could find and it does fix
the issue.
The same changes were added in svn r26856 by Gabor Juhos:
ar71xx: ag71xx: make switch register access atomic
As I can't find the underlying problem either, this hack is broght
back to fix the unstable link issue.
This hack is only suitable for ath79 mdio and may easily break the
driver on other platform. Limit it to ath79-only as a target patch.
Paul Spooren [Tue, 29 Sep 2020 09:09:22 +0000 (23:09 -1000)]
refpolicy: fix path to setfiles and checkpolicy
Directly set path via MAKE vars instead of defning TESTTOOLS. This way
setfiles, which is required by the ImageBuilder, ends up in /host/bin
while checkpolicy can stay in hostpkg/bin.
David Bauer [Mon, 28 Sep 2020 20:57:35 +0000 (22:57 +0200)]
rockchip: rk3328: add compatible to NanoPi R2S ethernet PHY
This adds the compatible property to the NanoPi R2S ethernet PHY node.
Otherwise, the PHY might not be probed, as the PHY ID reads all 0xff
when it is still in reset.
Daniel Golle [Tue, 29 Sep 2020 00:46:25 +0000 (01:46 +0100)]
image.mk: evaluate /etc/selinux/config to choose SELinux policy
Instead of hardcoding 'targeted' policy, evaluate /etc/selinux/config
in rootfs to choose according to which policy files in the rootfs got
to be labeled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Mon, 28 Sep 2020 08:37:53 +0000 (22:37 -1000)]
policycoreutils: install to host/bin not hostpkg
By installing policycoreutils to host/bin it is also available within
the ImageBuilder and SDK, allowing to correctly label both filesystems
and packages.
David Bauer [Sun, 27 Sep 2020 08:11:11 +0000 (10:11 +0200)]
ath10k-firmware: package Wave1 from linux-firmware
The firmware for Wave1 chips was updated to the latest release
10.2.4-1.0-00047 at the end of 2019 (commit 513d70cc50b).
Package firmware for these chips from linux-firmware.
This avoids downloading the ath10k-firmware repository.
Piotr Dymacz [Wed, 19 Aug 2020 14:01:25 +0000 (16:01 +0200)]
ath79: add support for Hak5 WiFi Pineapple NANO
Hak5 WiFi Pineapple NANO is an "USB dongle" device dedicated for Wi-Fi
pentesters. This device is based on Atheros AR9331 and AR9271. Support
for it was first introduced in 950b278c81 (ar71xx). FCC ID: 2AB87-NANO.
Specifications:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1T1R 2.4 GHz Wi-Fi (AR9331)
- 1T1R 2.4 GHz Wi-Fi (AR9271L), with ext. PA and LNA (Qorvo RFFM4203)
- 2x RP-SMA antenna connectors
- 1x USB 2.0 to 10/100 Ethernet bridge (ASIX AX88772A)
- integrated 4-port USB 2.0 HUB: Alcor Micro AU6259:
- 1x USB 2.0
- 1x microSD card reader (Genesys Logic GL834L)
- Atheros AR9271L
- 1x LED, 1x button
- UART (4-pin, 2 mm pitch) header on PCB
- USB 2.0 Type-A plug for power and AX88772A
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE.
Piotr Dymacz [Wed, 19 Aug 2020 13:10:04 +0000 (15:10 +0200)]
ath79: add support for Hak5 Packet Squirrel
Hak5 Packet Squirrel is a pocket-sized device dedicated for pentesters
(MITM attacks). This device is based on Atheros AR9331 but it lacks
WiFi. Support for it was first introduced in 950b278c81 (ar71xx).
Specifications:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x RJ45 10/100 Mbps Ethernet (AR9331)
- 1x USB 2.0
- 1x RGB LED, 1x button, 1x 4-way mechanical switch
- 1x Micro USB Type-B for main power input
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE.
Piotr Dymacz [Wed, 19 Aug 2020 12:20:54 +0000 (14:20 +0200)]
ath79: add support for Hak5 LAN Turtle
Hak5 LAN Turtle is an "USB Ethernet Adapter" shaped device dedicated for
sysadmins and pentesters. This device is based on Atheros AR9331 but it
lacks WiFi. Support for it was first introduced in 950b278c81 (ar71xx).
Two different versions of this device exist and it's up to the user to
install required drivers (generic image supports only common features):
- LAN Turtle 3G with Quectel UG96 3G modem
- LAN Turtle SD with microSD card reader (Alcorlink AU6435R)
Specifications:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x RJ45 10/100 Mbps Ethernet (AR9331)
- 1x USB 2.0 to 10/100 Ethernet bridge (Realtek RTL8152B)
- 2x LED (power, system), 1x button (inside, on the PCB)
- USB 2.0 Type-A plug for power and RTL8152B
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE.
Piotr Dymacz [Tue, 12 May 2020 21:44:10 +0000 (23:44 +0200)]
ath79: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Support for this device was first introduced in 4b0eebe9df (ar71xx
target) but users are advised to migrate from ar71xx target without
preserving settings as ath79 support includes some changes in network
and LED default configuration. They were aligned with vendor firmware
and recently added N2Q model (both Ethernet ports as LAN, labelled as
LAN1 and LAN2).
Specifications:
- Atheros AR9344
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz Wi-Fi, with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 2x IPEX/U.FL or MMCX antenna connectors (for PCBA version)
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Piotr Dymacz [Fri, 18 Sep 2020 16:55:23 +0000 (18:55 +0200)]
ath79: add support for ALFA Network N2Q
ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros
QCA9531 v2. This model is a successor of the old N2 which was based
on Atheros AR7240. FCC ID: 2AB8795311.
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA
- 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V)
- PoE pass through in second port (controlled by GPIO)
- support for optional 802.3af/at PoE module
- 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards)
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 mini Type-B (power controlled by GPIO)
- 8x LED (7 of them are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Piotr Dymacz [Thu, 2 Jul 2020 05:03:33 +0000 (07:03 +0200)]
ath79: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2, FCC
ID: 2AB879531.
Support for this device was first introduced in af8f0629df (ar71xx
target). When updating from previous release (and/or ar71xx target),
user should only adjust the WAN LED trigger type (netdev in ar71xx,
switch port in ath79).
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB (R36AH/-U2) or 64 MB (R36A) of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- Passive PoE input support (12~36 V) in RJ45 near DC jack
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 Type-A
- 1x USB 2.0 mini Type-B in R36AH-U2 version
- USB power is controlled by GPIO
- 6/7x LED (5/6 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- DC jack with lock, for main power input (12 V)
- UART (4-pin, 2.54 mm pitch) header on PCB
Optional/additional features in R36A series (R36A was the first model):
- for R36AH: USB 2.0 hub*
- for R36AH-U2: USB 2.0 hub*, 1x USB 2.0 mini Type-B, one more LED
*) there are at least three different USB 2.0 hub in R36AH/-U2 variants:
- Terminus-Tech FE 1.1
- Genesys Logic GL852G
- Genesys Logic GL850G (used in latests revision)
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Piotr Dymacz [Fri, 18 Sep 2020 12:11:13 +0000 (14:11 +0200)]
ath79: add support for Samsung WAM250
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344 (FCC ID: A3LWAM250). Support for this device
was first introduced in e58e49bdbe (ar71xx target).
Specifications:
- Atheros AR9344
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz Wi-Fi, with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
Piotr Dymacz [Sat, 21 Mar 2020 22:20:31 +0000 (23:20 +0100)]
ath79: add support for ALFA Network AP121FE
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Piotr Dymacz [Tue, 24 Mar 2020 23:02:08 +0000 (00:02 +0100)]
target.mk: enable iwinfo by default with any wpad variant
There are currently several variants of 'wpad' package but the 'iwinfo'
is included by default only if 'wpad', 'wpad-{basic*,mini}' or 'nas'
packages are included in {DEVICE,DEFAULT}_PACKAGES. Use 'wpad-*'
pattern to include 'iwinfo' with any 'wpad' variant.
Daniel Golle [Sun, 27 Sep 2020 16:10:34 +0000 (17:10 +0100)]
policycoreutils: fix host utils rpath and bin directory
'setfiles' and others should be installed to $(STAGING_DIR_HOSTPKG)/bin
rather than $(...)/sbin which isn't in PATH.
Also using -Wl,-rpath to set library search location instead of setting
LD_LIBRARY_PATH when calling setfiles in image.mk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ramips: move dts-v1 statement to top-level DTSI files
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ramips, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent mtxxxx/rtxxxx DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
Therefore, adding it to a DTS _and_ a DTSI file is actually wrong,
as it will be present twice then (though the compiler does not
complain about it).
In ipq40xx, the dts-v1 statement is already included in
qcom-ipq4019.dtsi, so we don't have to add it anywhere at all.
However, based on the conditions stated above, this requires
qcom-ipq4019.dtsi to be included as the first file in any DTS(I).
Consequently, this patch removes all cases of dts-v1 for the
ipq40xx target, and moves the includes accordingly where necessary.
While at it, remove a few obviously unneeded includes on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
projects / thirdparty / openwrt.git / log
