When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While VF2VF with RSS communication, RSS Type were wrongly recognized
and RSS hash was not calculated as it should be. Packets was
distributed on various queues by accident.
This commit fixes that behaviour and causes proper RSS Type recognition.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be a problem in the x540's internal switch wherein if SR-IOV
mode is enabled and an offloaded IPsec packet is sent to a local VF,
the packet is silently dropped. This might never be a problem as it is
somewhat a corner case, but if someone happens to be using IPsec offload
from the PF to a VF that just happens to get migrated to the local box,
communication will mysteriously fail.
Not good.
A simple way to protect from this is to simply not allow any IPsec offloads
for outgoing packets when num_vfs != 0. This doesn't help any offloads that
were created before SR-IOV was enabled, but we'll get to that later.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes we have empty banks within the GPIO block. This commit allows
proper handling of 0 width GPIO banks. We handle 0 width GPIO banks by
incrementing the bank and number of GPIOs, but not initializing them.
This will mean a call into the non-existent GPIOs will return an error.
Also remove "GPIO registered" dev print. This information is misleading
since the incremented banks and gpio_base do not reflect the actual GPIOs
that get initialized. We leave this information out since it is already
printed with dev_dbg.
If recvlength is less than MESSAGE_HEADER_LEN (4) we would end up
corrupting memory.
Fixes: c305a19a0d0a ("libertas_tf: usb specific functions") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are only 128 entries in vf vlan table, if user has added
more than 128 vlan, fw will ignore it and disable the vf vlan
table. So when user deletes the vlan entry that has not been
set to vf vlan table, fw will return not found result and driver
treat that as error, which will cause vlan delete failed problem.
This patch fixes it by returning ok when fw returns not found
result.
Fixes: 6c251711b37f ("net: hns3: Disable vf vlan filter when vf vlan table is full") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ping is runnig and user executes the loopback selftest, the
ping cmd will stop and exit.
This patch fixes it by using the hns3_nic_net_open/stop to offline
the netdev when doing loopback selftest.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When netdev is down, the stack will delete the vlan from
hardware including vlan0, which will cause problem when
doing loopback selftest when netdev is down.
This patch fixes it by always preserving vlan 0 in hardware,
because vlan 0 is defalut vlan, which should always be in
hardware.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem. Let's fix it there too.
Fixes: b4c45fe974bc ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem. Let's fix it there too.
NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute. If the last element (has_arg) is false then you need
to do the -EINVAL trick.
ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that. It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.
When we don't have the iputils-debuginfo package installed, i.e. when we
don't have the DWARF information needed to resolve ping's samples, we
end up failing this 'perf test' entry:
# perf test ping
62: probe libc's inet_pton & backtrace it with ping : Ok
# rpm -e iputils-debuginfo
# perf test ping
62: probe libc's inet_pton & backtrace it with ping : FAILED!
#
Fix it to accept "[unknown]" where the symbol + offset, when resolved,
is expected.
I think this will fail in the other arches as well, but since I can't
test now, I'm leaving s390x and ppc cases as-is.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kim Phillips <kim.phillips@arm.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Sandipan Das <sandipan@linux.vnet.ibm.com> Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Cc: Thomas Richter <tmricht@linux.vnet.ibm.com> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 7903a7086723 ("perf script: Show symbol offsets by default") Link: https://lkml.kernel.org/n/tip-hnizqwqrs03vcq1b74yao0f6@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/net_failover.c: In function 'net_failover_slave_unregister':
drivers/net/net_failover.c:598:35: warning:
variable 'primary_dev' set but not used [-Wunused-but-set-variable]
There should check the validity of 'slave_dev'.
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Edward Cree says:
In check_mem_access(), for the PTR_TO_CTX case, after check_ctx_access()
has supplied a reg_type, the other members of the register state are set
appropriately. Previously reg.range was set to 0, but as it is in a
union with reg.map_ptr, which is larger, upper bytes of the latter were
left in place. This then caused the memcmp() in regsafe() to fail,
preventing some branches from being pruned (and occasionally causing the
same program to take a varying number of processed insns on repeated
verifier runs).
Fix the instability by clearing bpf_reg_state in __mark_reg_[un]known()
Fixes: f1174f77b50c ("bpf/verifier: rework value tracking") Debugged-by: Edward Cree <ecree@solarflare.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.
Fixes: 0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode") Cc: Doug Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).
Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.
This commit adds support for the 80862286 and 808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a logical problem in spi-gpio with host just
assigning a MOSI line and no MISO: this is interpreted
as the host cannot do RX and the host is flagged with
SPI_MASTER_NO_RX.
This is wrong: since GPIO lines can switch direction,
in 3WIRE operation the host will simply reverse the
direction of the GPIO line and start reading from it,
there is even code for doing this in the driver, but
it went unnoticed because it was tested by using a
master with 4 wires but a device using just 3 wires.
Remove the offending flag.
Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than panic() when taking an undefined instruction exception from
EL1, allow a hook to be registered in case we want to emulate the
instruction, like we will for the SSBS PSTATE manipulation instructions.
BFQ schedules entities (which represent either per-process queues or
groups of queues) as a function of their timestamps. In particular, as
a function of their (virtual) finish times. The finish time of an
entity is computed as a function of the budget assigned to the entity,
assuming, tentatively, that the entity, once in service, will receive
an amount of service equal to its budget. Then, when the entity is
expired because it finishes to be served, this finish time is updated
as a function of the actual service received by the entity. This
allows the entity to be correctly charged with only the service
received, and then to be correctly re-scheduled.
Yet an entity may receive service also while not being the entity in
service (in the scheduling environment of its parent entity), for
several reasons. If the entity remains with no backlog while receiving
this 'unofficial' service, then it is expired. Also on such an
expiration, the finish time of the entity should be updated to account
for only the service actually received by the entity. Unfortunately,
such an update is not performed for an entity expiring without being
the entity in service.
In a similar vein, the service counter of the entity in service is
reset when the entity is expired, to be ready to be used for next
service cycle. This reset too should be performed also in case an
entity is expired because it remains empty after receiving service
while not being the entity in service. But in this case the reset is
not performed.
This commit performs the above update of the finish time and reset of
the service received, also for an entity expiring while not being the
entity in service.
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We clear STATE_DOWN bit of hdev state when starting net, but do not set
it again when stopping net. It causes that the net is down, but hdev state
is still up. STATE_DOWN bit of hdev state should be set when stopping net.
By default, HW link status is up. If hclge_update_link_status is called
before net up, driver will print "link up". It is not suitable. hdev
state check is needed when getting link status.
./drivers/pinctrl/sunxi/pinctrl-sunxi.c:1112 sunxi_pinctrl_build_state()
warn: passing devm_ allocated variable to kfree. 'pctrl->functions'
As we will be calling krealloc() on pointer 'pctrl->functions', which means
kfree() will be called in there, devm_kzalloc() shouldn't be used with
the allocation in the first place. Fix the warning by calling kcalloc()
and managing the free procedure in error path on our own.
There is a defect in hclge_ets_validate(). If each member of tc_tsa is
not IEEE_8021QAZ_TSA_ETS, the variable total_ets_bw won't be updated.
In this case, the check for value of total_ets_bw will fail. This patch
fixes it by checking total_ets_bw only after it has been updated.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When nic down, it firstly calls netif_tx_stop_all_queues(), then calls
napi_disable(). But napi_disable() will wait current napi_poll finish,
it may call netif_tx_wake_queue(). This patch fixes it by add nic state
checking.
Fixes: 424eb834a9be ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently align the end of the compressed image to a multiple of
16. However, the PE-COFF header included in the EFI stub says that
the file alignment is 32 bytes, and when adding an EFI signature to
the file it must first be padded to this alignment.
sbsigntool commands warn about this:
warning: file-aligned section .text extends beyond end of file
warning: checksum areas are greater than image size. Invalid section table?
Worse, pesign -at least when creating a detached signature- uses the
hash of the unpadded file, resulting in an invalid signature if
padding is required.
Avoid both these problems by increasing alignment to 32 bytes when
CONFIG_EFI_STUB is enabled.
Before this commit we were only calling efi_parse_options() from
make_boot_params(), but make_boot_params() only gets called if the
kernel gets booted directly as an EFI executable. So when booted through
e.g. grub we ended up not parsing the commandline in the boot code.
This makes the drivers/firmware/efi/libstub code ignore the "quiet"
commandline argument resulting in the following message being printed:
"EFI stub: UEFI Secure Boot is enabled."
Despite the quiet request. This commits adds an extra call to
efi_parse_options() to efi_main() to make sure that the options are
always processed. This fixes quiet not working.
This also fixes the libstub code ignoring nokaslr and efi=nochunk.
Reported-by: Peter Robinson <pbrobinson@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flag KASAN is set, we are seeing an following crash while removing
hci_uart module.
[ 50.589909] Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b73
[ 50.597902] Mem abort info:
[ 50.600846] Exception class = DABT (current EL), IL = 32 bits
[ 50.606959] SET = 0, FnV = 0
[ 50.610142] EA = 0, S1PTW = 0
[ 50.613396] Data abort info:
[ 50.616401] ISV = 0, ISS = 0x00000004
[ 50.620373] CM = 0, WnR = 0
[ 50.623466] [006b6b6b6b6b6b73] address between user and kernel address ranges
[ 50.630818] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 50.671670] PC is at qca_power_shutdown+0x28/0x100 [hci_uart]
[ 50.677593] LR is at qca_close+0x74/0xb0 [hci_uart]
[ 50.775689] Process rmmod (pid: 2144, stack limit = 0xffffff801ba90000)
[ 50.782493] Call trace:
This patch adds the device ID for the AMPAK AP6335 combo module used
in the 1st generation WeTek Hub Android/LibreELEC HTPC box. The WiFI
chip identifies itself as BCM4339, while Bluetooth identifies itself
as BCM4335 (rev C0):
The hardware expects a unit of 128 bytes when setting
packet buffer. When calculating the packet buffer size,
hclge_rx_buffer_calc does not round up the size as a unit
of 128 byte, which may casue packet lost problem when stress
testing.
This patch fixes it by rounding up packet size when calculating.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have MAX_FW_API_VER_BRANCH, MAX_FW_API_VER_MAJOR, and
MAX_FW_API_VER_MINOR that we use in ice_controlq.h to test when a
firmware version is newer than expected. This is currently tested by
comparing each field separately. Thus, we compare the branch field
against the MAX_FW_API_VER_BRANCH, and so forth.
This means that currently, if we suppose that the max firmware version
is defined as 0.2.1, i.e.
Then firmware 0.1.3 will fail to load. This is because the minor version
3 is greater than the max minor version 1.
This is not intuitive, because of the notion that increasing the major
firmware version to 2 should mean any firmware version with a major
version is less than 2 should be considered older than 2...
In order to allow both 0.2.1 and 0.1.3 to load, you would have to define
the "max" firmware version as 0.2.3.. It is possible that such
a firmware version doesn't even exist yet!
Fix this by replacing the current logic with an updated check that
behaves as follows:
First, we check the major version. If it is greater than the expected
version, then we prevent driver load. Additionally, a warning message is
logged to indicate to the system administrator that they need to update
their driver. This is now the only case where the driver will refuse to
load.
Second, if the major version is less than the expected version, we log
an information message indicating the NVM should be updated.
Third, if the major version is exact, we'll then check the minor
version. If the minor version is more than two versions less than
expected, we log an information message indicating the NVM should be
updated. If it is more than two versions greater than the expected
version, we log an information message that the driver should be
updated.
To support this, the ice_aq_ver_check function needs its signature
updated to pass the HW structure. Since we now pass this structure,
there is no need to pass the firmware API versions separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rx_mini_pending was set to an incorrect value. This was causing EINVAL to
always be returned to 'ethtool -G'. The driver does not support mini or
jumbo rings so the respective settings should be zero.
Also, change the valid range of the number of descriptors in the rings to
make the code simpler and easier for users to understand (this removes the
valid settings of 8 and 16). Add a system log message indicating when the
number is rounded-up from what the user specifies with the 'ethtool -G'
command (i.e. when it is not a multiple of 32), and update the log message
when a user-provided value is out of range to also indicate the stride.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sigaltstack(2) system call fails with -ENOMEM if the new alternative
signal stack is found to be smaller than SIGMINSTKSZ. On architectures
such as arm64, where the native value for SIGMINSTKSZ is larger than
the compat value, this can result in an unexpected error being reported
to a compat task. See, for example:
This patch fixes the problem by extending do_sigaltstack to take the
minimum signal stack size as an additional parameter, allowing the
native and compat system call entry code to pass in their respective
values. COMPAT_SIGMINSTKSZ is just defined as SIGMINSTKSZ if it has not
been defined by the architecture.
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Oleg Nesterov <oleg@redhat.com> Reported-by: Steve McIntyre <steve.mcintyre@arm.com> Tested-by: Steve McIntyre <93sam@debian.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_status for management frames is being filled
incorrectly in the flags of skb_cb. This incorrect
flag setting causes the upper layers to consider that
the particular frame was not transmitted properly,
leading to improper behavior.
Set the IEEE80211_TX_STAT_ACK flag in the info flags
of skb_cb, to indicate the successful transmission of
the management frame.
When an io is rejected by nvmf_check_ready() due to validation of the
controller state, the nvmf_fail_nonready_command() will normally return
BLK_STS_RESOURCE to requeue and retry. However, if the controller is
dying or the I/O is marked for NVMe multipath, the I/O is failed so that
the controller can terminate or so that the io can be issued on a
different path. Unfortunately, as this reject point is before the
transport has accepted the command, blk-mq ends up completing the I/O
and never calls nvme_complete_rq(), which is where multipath may preserve
or re-route the I/O. The end result is, the device user ends up seeing an
EIO error.
Example: single path connectivity, controller is under load, and a reset
is induced. An I/O is received:
a) while the reset state has been set but the queues have yet to be
stopped; or
b) after queues are started (at end of reset) but before the reconnect
has completed.
The I/O finishes with an EIO status.
This patch makes the following changes:
- Adds the HOST_PATH_ERROR pathing status from TP4028
- Modifies the reject point such that it appears to queue successfully,
but actually completes the io with the new pathing status and calls
nvme_complete_rq().
- nvme_complete_rq() recognizes the new status, avoids resetting the
controller (likely was already done in order to get this new status),
and calls the multipather to clear the current path that errored.
This allows the next command (retry or new command) to select a new
path if there is one.
Signed-off-by: James Smart <jsmart2021@gmail.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value") Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can not call dev_pm_opp_of_cpumask_remove_table() freely anymore
since the latest OPP core updates as that uses reference counting to
free resources. There are cases where no static OPPs are added (using
DT) for a platform and trying to remove the OPP table may end up
decrementing refcount which is already zero and hence generating
warnings.
Lets track if we were able to add static OPPs or not and then only
remove the table based on that. Some reshuffling of code is also done to
do that.
ACPI driver should make sure all the processor IDs in their ACPI Namespace
are unique. the driver performs a depth-first walk of the namespace tree
and calls the acpi_processor_ids_walk() to check the duplicate IDs.
But, the acpi_processor_ids_walk() mistakes the return value. If a
processor is checked, it returns true which causes the walk break
immediately, and other processors will never be checked.
Repace the value with AE_OK which is the standard acpi_status value.
And don't abort the namespace walk even on error.
Fixes: 8c8cb30f49b8 (acpi/processor: Implement DEVICE operator for processor enumeration) Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI Low Power S0 Idle capabilities are announced via FADT table and can
be used to inform the kernel about the presence of one or more Low Power
Idle (LPI) entries as descried in LPIT table. LPIT table can exist
independently even if the FADT S0 Idle flag is not set and thus it could
confuse user since the following cpuidle attributes are created.
The type of a cache might not be specified by architectural mechanisms (ie
system registers), but its type might be specified in the PPTT. In this
case, we should populate the type of the cache, rather than leave it
undefined.
This fixes the issue where the cacheinfo driver will not populate sysfs
for such caches, resulting in the information missing from utilities like
lstopo and lscpu, thus degrading the user experience.
Fixes: 2bd00bcd73e5 (ACPI/PPTT: Add Processor Properties Topology Table parsing) Reported-by: Vijaya Kumar K <vkilari@codeaurora.org> Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:
BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...
After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.
And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.
Cc: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On OLPC XO-1, the RTC is discovered via device tree from the arch
initcall. Don't let the PC platform register another one from its device
initcall, it's not going to work:
sysfs: cannot create duplicate filename '/devices/platform/rtc_cmos'
CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #12
Hardware name: OLPC XO/XO, BIOS OLPC Ver 1.00.01 06/11/2014
Call Trace:
dump_stack+0x16/0x18
sysfs_warn_dup+0x46/0x58
sysfs_create_dir_ns+0x76/0x9b
kobject_add_internal+0xed/0x209
? __schedule+0x3fa/0x447
kobject_add+0x5b/0x66
device_add+0x298/0x535
? insert_resource_conflict+0x2a/0x3e
platform_device_add+0x14d/0x192
? io_delay_init+0x19/0x19
platform_device_register+0x1c/0x1f
add_rtc_cmos+0x16/0x31
do_one_initcall+0x78/0x14a
? do_early_param+0x75/0x75
kernel_init_freeable+0x152/0x1e0
? rest_init+0xa2/0xa2
kernel_init+0x8/0xd5
ret_from_fork+0x2e/0x38
kobject_add_internal failed for rtc_cmos with -EEXIST, don't try to
register things with the same name in the same directory.
platform rtc_cmos: registered platform RTC device (no PNP device found)
When reading the profiles from the EWRD table in ACPI, we loop over
the data and set it into our internal table. We use the number of
profiles specified in ACPI without checking its validity, so if the
ACPI table is corrupted and the number is larger than our array size,
we will try to make an out-of-bounds access.
Fix this by making sure the value specified in the ACPI table is
valid.
Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
queue which means that the worker will not run for now
since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
and that we are now resuming from suspend and cancels
the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
and doesn't really allocate a station ID for the aux
station
17) a new queue is added for the aux station
Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.
Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:
The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:
Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
NAND devices need additional data area (OOB) for error correction,
but it is also used for Bad Block Marker (BBM). In many cases, the
first byte in OOB is used for BBM, but the location actually depends
on chip vendors. The NAND controller should preserve the precious
BBM to keep track of bad blocks.
In Denali IP, the SPARE_AREA_SKIP_BYTES register is used to specify
the number of bytes to skip from the start of OOB. The ECC engine
will automatically skip the specified number of bytes when it gets
access to OOB area.
The same value for SPARE_AREA_SKIP_BYTES should be used between
firmware and the operating system if you intend to use the NAND
device across the control hand-off.
In fact, the current denali.c code expects firmware to have already
set the SPARE_AREA_SKIP_BYTES register, then reads the value out.
If no firmware (or bootloader) has initialized the controller, the
register value is zero, which is the default after power-on-reset.
In other words, the Linux driver cannot initialize the controller
by itself.
Some possible solutions are:
[1] Add a DT property to specify the skipped bytes in OOB
[2] Associate the preferred value with compatible
[3] Hard-code the default value in the driver
My first attempt was [1], but in the review process, [3] was suggested
as a counter-implementation.
(https://lore.kernel.org/patchwork/patch/983055/)
The default value 8 was chosen to match to the boot ROM of the UniPhier
platform. The preferred value may vary by platform. If so, please
trade up to a different solution.
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
Forgot to include the maintainers with my first email.
Somewhere between Michael Lyle's original
"bcache: PI controller for writeback rate V2" patch dated 07 Sep 2017
and 1d316e6 bcache: implement PI controller for writeback rate,
the mapping of the writeback_rate_minimum attribute was dropped.
Re-add the missing sysfs writeback_rate_minimum attribute mapping to
"allow the user to specify a minimum rate at which dirty blocks are
retired."
Fixes: 1d316e6 ("bcache: implement PI controller for writeback rate") Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpupower crashes on VMWare guests. The guests have the AMD PStateDef MSR
(0xC0010064 + state number) set to zero. As a result fid and did are zero
and the crash occurs because of a divide by zero (cof = fid/did). This
can be prevented by checking the enable bit in the PStateDef MSR before
calculating cof. By doing this the value of pstate[i] remains zero and
the value can be tested before displaying the active Pstates.
Check the enable bit in the PstateDef register for all supported families
and only print out enabled Pstates.
parse_ftrace_printk() tokenizes and parses a line, calling strdup() each
iteration. Add code to free this temporary format string duplicate.
Fixes the following coverity complaints:
Error: RESOURCE_LEAK (CWE-772):
tools/perf/util/trace-event-parse.c:158: overwrite_var: Overwriting
"printk" in "printk = strdup(fmt + 1)" leaks the storage that "printk"
points to.
tools/perf/util/trace-event-parse.c:162: leaked_storage: Variable
"printk" going out of scope leaks the storage it points to.
Signed-off-by: Sanskriti Sharma <sansharm@redhat.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Link: http://lkml.kernel.org/r/1538490554-8161-4-git-send-email-sansharm@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For each system in a given pevent, read_event_files() reads in a
temporary 'sys' string. Be sure to free this string before moving onto
to the next system and/or leaving read_event_files().
Fixes the following coverity complaints:
Error: RESOURCE_LEAK (CWE-772):
tools/perf/util/trace-event-read.c:343: overwrite_var: Overwriting
"sys" in "sys = read_string()" leaks the storage that "sys" points to.
tools/perf/util/trace-event-read.c:353: leaked_storage: Variable "sys"
going out of scope leaks the storage it points to.
Signed-off-by: Sanskriti Sharma <sansharm@redhat.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Link: http://lkml.kernel.org/r/1538490554-8161-6-git-send-email-sansharm@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pblk, when a new line is allocated, metadata for the previously
written line is scheduled. This is done through a fixed memory region
that is shared through time and contexts across different lines and
therefore protected by a lock. Unfortunately, this lock is not properly
covering all the metadata used for sharing this memory regions,
resulting in a race condition.
This patch fixes this race condition by protecting this metadata
properly.
pblk exposes a sysfs interface that represents its internal state. Part
of this state is the map bitmap for the current open line, which should
be protected by the line lock to avoid a race when freeing the line
metadata. Currently, it is not.
This patch makes sure that the line state is consistent and NULL
bitmap pointers are not dereferenced.
Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.
One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.
Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.
The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
When running as a level 3 guest with no host provided sthyi support
sclp_ocf_cpc_name_copy() will only return zeroes. Zeroes are not a
valid group name, so let's not indicate that the group name field is
valid.
Also the group name is not dependent on stsi, let's not return based
on stsi before setting it.
Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.
This can be visualized with following ip-link(8) command sequences:
# ip link set dev tun0 group 100
# ip link set dev tun0 group 100 type tun
RTNETLINK answers: Invalid argument
with contrast to dummy and veth drivers:
# ip link set dev dummy0 group 100
# ip link set dev dummy0 type dummy
# ip link set dev veth0 group 100
# ip link set dev veth0 group 100 type veth
Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.
Fixes: f019a7a594d9 ("tun: Implement ip link del tunXXX") Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: Ryan C Goodfellow <rgoodfel@isi.edu> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Greg Weeks <greg.weeks@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VF device's serial number is saved as a string in PCI slot's
kobj name, not the slot->number. This patch corrects the netvsc
driver, so the VF device can be successfully paired with synthetic
NIC.
Fixes: 00d7ddba1143 ("hv_netvsc: pair VF based on serial number") Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The matches() routine for a capability must honor the "scope"
passed to it and return the proper results.
i.e, when passed with SCOPE_LOCAL_CPU, it should check the
status of the capability on the current CPU. This is used by
verify_local_cpu_capabilities() on a late secondary CPU to make
sure that it's compliant with the established system features.
However, ARM64_HAS_CACHE_{IDC/DIC} always checks the system wide
registers and this could mean that a late secondary CPU could return
"true" (since the CPU hasn't updated the system wide registers yet)
and thus lead the system in an inconsistent state, where
the system assumes it has IDC/DIC feature, while the new CPU
doesn't.
Fixes: commit 6ae4b6e0578886eb36 ("arm64: Add support for new control bits CTR_EL0.DIC and CTR_EL0.IDC") Cc: Philip Elcan <pelcan@codeaurora.org> Cc: Shanker Donthineni <shankerd@codeaurora.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to allocate the request queue for a disk, we still need to
free that disk, not just the previous ones. Additionally, we need to
cleanup the previous request queues.
Move queue allocation next to disk allocation to fix a couple of issues:
- If add_disk() hasn't been called, we should clear disk->queue before
calling put_disk().
- If we fail to allocate a request queue, we still need to put all of
the disks, not just the ones that we allocated queues for.
The commit 2eb0f624b709 ("netfilter: add NAT support for shifted
portmap ranges") did not set the checkentry/destroy callbacks for
the newly added DNAT target. As a result, rulesets using only
such nat targets are not effective, as the relevant conntrack hooks
are not enabled.
The above affect also nft_compat rulesets.
Fix the issue adding the missing initializers.
Fixes: 2eb0f624b709 ("netfilter: add NAT support for shifted portmap ranges") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was found that when debug_locks was turned off because of a problem
found by the lockdep code, the system performance could drop quite
significantly when the lock_stat code was also configured into the
kernel. For instance, parallel kernel build time on a 4-socket x86-64
server nearly doubled.
Further analysis into the cause of the slowdown traced back to the
frequent call to debug_locks_off() from the __lock_acquired() function
probably due to some inconsistent lockdep states with debug_locks
off. The debug_locks_off() function did an unconditional atomic xchg
to write a 0 value into debug_locks which had already been set to 0.
This led to severe cacheline contention in the cacheline that held
debug_locks. As debug_locks is being referenced in quite a few different
places in the kernel, this greatly slow down the system performance.
To prevent that trashing of debug_locks cacheline, lock_acquired()
and lock_contended() now checks the state of debug_locks before
proceeding. The debug_locks_off() function is also modified to check
debug_locks before calling __debug_locks_off().
Signed-off-by: Waiman Long <longman@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: http://lkml.kernel.org/r/1539913518-15598-1-git-send-email-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least UDP / TCP stacks can now cook skbs with a tstamp using
MONOTONIC base (or arbitrary values with SCM_TXTIME)
Since loopback driver does not call (directly or indirectly)
skb_scrub_packet(), we need to clear skb->tstamp so that
net_timestamp_check() can eventually resample the time,
using ktime_get_real().
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.") Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We observed that packets and bytes count are not reset
when user performs interface down. Eventually, tx queue is
exhausted and packets will not be sent out.
To avoid this problem, resets tx queue in ndo_stop.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver") Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have
external pull-up resistors, so disable any pull control for those lines
in respective pin controller node. This fixes support for MAX8997
interrupts and enables operation of wakeup from MAX8997 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 17419726aaa1 ("ARM: dts: add max8997 device node for exynos4210-origen board") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The numa_emulation() routine in the 'uniform' case walks through all the
physical 'memblk' instances and divides them into N emulated nodes with
split_nodes_size_interleave_uniform(). As each physical node is consumed it
is removed from the physical memblk array in the numa_remove_memblk_from()
helper.
Since split_nodes_size_interleave_uniform() handles advancing the array as
the 'memblk' is consumed it is expected that the base of the array is
always specified as the argument.
Otherwise, on multi-socket (> 2) configurations the uniform-split
capability can generate an invalid numa configuration leading to boot
failures with signatures like the following:
rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
Sending NMI from CPU 0 to CPUs 2:
NMI backtrace for cpu 2
CPU: 2 PID: 1332 Comm: pgdatinit0 Not tainted 4.19.0-rc8-next-20181019-baseline #59
RIP: 0010:__init_single_page.isra.74+0x81/0x90
[..]
Call Trace:
deferred_init_pages+0xaa/0xe3
deferred_init_memmap+0x18f/0x318
kthread+0xf8/0x130
? deferred_free_pages.isra.105+0xc9/0xc9
? kthread_stop+0x110/0x110
ret_from_fork+0x35/0x40
Fixes: 1f6a2c6d9f121 ("x86/numa_emulation: Introduce uniform split capability") Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/154049911459.2685845.9210186007479774286.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable preemption during CR3 reset / __flush_tlb_all() and add a comment
why preemption has to be disabled so it won't be removed accidentaly.
Add another preemptible() check in __flush_tlb_all() to catch callers with
enabled preemption when PGE is enabled, because PGE enabled does not
trigger the warning in __native_flush_tlb(). Suggested by Andy Lutomirski.
Fixes: decab0888e6e ("x86/mm: Remove preempt_disable/enable() from __native_flush_tlb()") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20181017103432.zgv46nlu3hc7k4rq@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memory_corruption_check[{_period|_size}]()'s handlers do not check input
argument before passing it to kstrtoul() or simple_strtoull(). The argument
would be a NULL pointer if each of the kernel parameters, without its
value, is set in command line and thus cause the following panic.
The boot loader version reported via sysfs is wrong in case of the
kernel being booted via the Xen PVH boot entry. it should be 2.12
(0x020c), but it is reported to be 2.18 (0x0212).
As the current way to set the version is error prone use the more
readable variant (2 << 8) | 12.
STIBP is a feature provided by certain Intel ucodes / CPUs. This feature
(once enabled) prevents cross-hyperthread control of decisions made by
indirect branch predictors.
Enable this feature if
- the CPU is vulnerable to spectre v2
- the CPU supports SMT and has SMT siblings online
- spectre_v2 mitigation autoselection is enabled (default)
After some previous discussion, this leaves STIBP on all the time, as wrmsr
on crossing kernel boundary is a no-no. This could perhaps later be a bit
more optimized (like disabling it in NOHZ, experiment with disabling it in
idle, etc) if needed.
Note that the synchronization of the mask manipulation via newly added
spec_ctrl_mutex is currently not strictly needed, as the only updater is
already being serialized by cpu_add_remove_lock, but let's make this a
little bit more future-proof.
Since the commit c647f806b8c2 ("ALSA: hda - Allow multiple ADCs for
mic mute LED controls") we allow enabling the mic mute LED with
multiple ADCs. The commit changed the function return value to be
zero or a negative error, while this change was overlooked in the
thinkpad_acpi helper code where it still expects a positive return
value for success. This eventually leads to a NULL dereference on a
system that has only a mic mute LED.
This patch corrects the return value check in the corresponding code
as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201621 Fixes: c647f806b8c2 ("ALSA: hda - Allow multiple ADCs for mic mute LED controls") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Creative Audigy SE (SB0570) card currently exhibits an audible pop
whenever playback is stopped or resumed, or during silent periods of an
audio stream. Initialise the IZD bit to the 0 to eliminate these pops.
The Infinite Zero Detection (IZD) feature on the DAC causes the output
to be shunted to Vcap after 2048 samples of silence. This discharges the
AC coupling capacitor through the output and causes the aforementioned
pop/click noise.
The behaviour of the IZD bit is described on page 15 of the WM8768GEDS
datasheet: "With IZD=1, applying MUTE for 1024 consecutive input samples
will cause all outputs to be connected directly to VCAP. This also
happens if 2048 consecutive zero input samples are applied to all 6
channels, and IZD=0. It will be removed as soon as any channel receives
a non-zero input". I believe the second sentence might be referring to
IZD=1 instead of IZD=0 given the observed behaviour of the card.
This change should make the DAC initialisation consistent with
Creative's Windows driver, as this popping persists when initialising
the card in Linux and soft rebooting into Windows, but is not present on
a cold boot to Windows.
The front MIC on the Lenovo M715 can't record sound, after applying
the ALC294_FIXUP_LENOVO_MIC_LOCATION, the problem is fixed. So add
the pin configuration of this machine to the pin quirk table.
BIOS on ASUS G751 doesn't seem to map the headphone pin (NID 0x16)
correctly. Add a quirk to address it, as well as chaining to the
previous fix for the microphone.
In the C-code we need to put the physical address of the hpmc handler in
the interrupt vector table (IVA) in order to get HPMCs working. Since
on parisc64 function pointers are indirect (in fact they are function
descriptors) we instead export the address as variable and not as
function.
This reverts a small part of commit f39cce654f9a ("parisc: Add
cfi_startproc and cfi_endproc to assembly code").
Fix a long-existing small nasty bug in the map_pages() implementation which
leads to overwriting already written pte entries with zero, *if* map_pages() is
called a second time with an end address which isn't aligned on a pmd boundry.
This happens for example if we want to remap only the text segment read/write
in order to run alternative patching on the code. Exiting the loop when we
reach the end address fixes this.
Helge noticed that the address of the os_hpmc handler was not being
correctly calculated in the hpmc macro. As a result, PDCE_CHECK would
fail to call os_hpmc:
acpi_pcc_probe() calls acpi_table_parse_entries_array() but fails
to check for an error return. This in turn can result in calling
kcalloc() with a negative count as well as emitting the following
misleading erorr message:
[ 2.642015] Could not allocate space for PCC mbox channels
Fixes: 8f8027c5f935 (mailbox: PCC: erroneous error message when parsing ACPI PCCT) Signed-off-by: David Arcari <darcari@redhat.com> Reviewed-by: Al Stone <ahs3@redhat.com> Cc: 4.18+ <stable@vger.kernel.org> # 4.18+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
a19b2e3d7839 ("kprobes/x86: Remove IRQ disabling from ftrace-based/optimized kprobes”)
removed local_irq_save/restore() from optimized_callback(), the handler
might be interrupted by the rescheduling interrupt and might be
rescheduled - so we must not use the preempt_enable_no_resched() macro.
Use preempt_enable() instead, to not lose preemption events.
projects / thirdparty / kernel / stable.git / log
