The patch implements optional internal export table to a channel and
hooks it to BGP so it can be used as Adj-RIB-Out. When enabled, all
exported (post-filtered) routes are stored there. An export table can be
examined using e.g. 'show route export table bgp1.ipv4'.
Several BGP channel options (including 'next hop self') could be
reconfigured without session reset, with just route refeed/refresh.
The patch improves reconfiguration code to do it that way.
BGP: Fix 'deterministic med' to work with 'merge paths'
The 'deterministic med' option is implemented by suppressing other than
best-in-group routes (grouped by ASN) from best route selection. This
interferes with 'merge paths' as supressed routes are no longer mergable
with best route. This is fixed by suppressing only those routes that are
not mergable with best-in-group route.
Per RFC 3101, N-bit signalling NSSA support should be used only in Hello
packets, not in DBDES packets. BIRD since 2.0.4 verifies N-bit in
neighbor structure, which is learned from DBDES packets, therefore
NSSA-LSAs are not propagated to proper implementations of RFC 3101.
This patch fixes that. Both removing the check and removing N-bit from
DBDES packet. This will fix compatibility issues with proper
implementations, but causes compatibility issues with BIRD 2.0.4.
OSPF: Fix handling of external routes on graceful restart
We need to flush learned external LSAs a bit later than other LSAs (after
first feed after end of the graceful restart) to avoid flap of external
routes.
Implement OSPFv2 (RFC 3623) and OSPFv3 (RFC 5187) graceful restart,
for both restarting and helper sides. Graceful restart is initiated
by 'graceful down' command.
When 'graceful down' command is entered, protocols are shut down
with regard to graceful restart. Namely Kernel protocol does
not remove routes and BGP protocol does not send notification,
just closes the connection.
Implicitly define rtables 'local4' and 'local6' and a pair of direct
protocols to fill them. Use modified net_route() for neighbor
lookup to avoid iterating over all interfaces.
Handle unresolvable routes (recursive routes that cannot be resolved) as
invalid, i.e. deprioritize tham and do not allow them for propagation.
Such route now shows as 'unresolvable' instead of 'unreachable'.
When area is reconfigured to a different type, we need to flush LSAs as
they may not be valid (e.g. NSSA-LSA for non-NSSA area). Also, when we
have have just one OSPF area and that changes type, we could restart OSPF
as there is no state to keep anyway. That solves issue with different
handling of external routes exported to OSPF based of main area type.
OSPF: Basic support for DN-bit handling (RFC 4576)
External LSAs originated by OSPF routers with VPN-PE behavior enabled are
marked by DN flag and they are ignored by other OSPF routers with VPN-PE
enabled.
In some circumstances (old LSA flushed but not acknowledged and not
removed) origination of a new LSA may wrongly triggers LSA collision
code. The patch fixes that.
Thanks to Asbjorn Mikkelsen for the bugreport and @mdelagueronniere
for the original patch.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
Direct acknowledgements should be send as unicast to a corresponding
neighbor. Only delayed acks should be send as multicast to all/designated
routers.
OSPF: Reject duplicate DBDES packets after dead interval
Master may free last DBDES packet immediately. Slave must wait dead
interval before freeing last DBDES packet and then reject duplicate
DBDES packets with SeqNumberMismatch.
The bgpmask literals can include expressions. This is OK but they have
to be interpreted as soon as the code is run, not in the time the code
is used as value.
This led to strange behavior like rewriting bgpmasks when they shan't
be rewritten:
function mask_generator(int as)
{
return [= * as * =];
}
function another()
bgpmask m1;
bgpmask m2;
{
m1 = mask_generator(10);
m2 = mask_generator(20);
if (m1 == m2) {
print("strange"); # this would happen
}
}
Moreover, sending this to CLI would cause stack overflow and knock down the
whole BIRD, as soon as there is at least one route to execute the given
filter on.
The magic match operator (~) inside the bgpmask literal would try to
resolve mmm, which points to the same bgpmask so it would resolve
itself, call the magic match operator and vice versa.
After this patch, the bgpmask literal will get resolved as soon as it's
assigned to mmm and it also will return a type error as bool is not
convertible to ASN in BIRD.
It was supposed to do tail-recursion in interpret() but it didn't
compile as such. Converting it to loop makes a significant filter
performance improvement for flat filters.
The two-letter instructions were quite messy but they could be easily
read from memory dumps. Now GDB (since 2012) supports pretty printing
enum values and GCC checks the switch construction for missing enum
values so we are converting the nice two-byte values to enums.
Anyway, the enum still keeps the old two-byte values to be able to read
the instruction codes even without GDB from plain memory dump.
This patch adds support for source-specific routing to the Babel protocol.
It changes the protocol to support both NET_IP6 and NET_IP6_SADR channels
for IPv6 addresses. If only a NET_IP6 channel is configured,
source-specific updates are ignored. Otherwise, non-source-specific
routes are simply treated as source-specific routes with SADR prefix 0.
Thanks to Toke Hoiland-Jorgensen for the original patch.
Minor changes by Ondrej Santiago Zajicek.
Add support for source-specific IPv6 routes to BIRD core
This patch adds support for source-specific IPv6 routes to BIRD core.
This is based on Dean Luga's original patch, with the review comments
addressed. SADR support is added to network address parsing in confbase.Y
and to the kernel protocol on Linux.
Currently there is no way to mix source-specific and non-source-specific
routes (i.e., SADR tables cannot be connected to non-SADR tables).
Thanks to Toke Hoiland-Jorgensen for the original patch.
Minor changes by Ondrej Santiago Zajicek.
On Linux, setting the ToS will also set the priority and the range of
accepted values is quite limited (masked by 0x1e). Therefore, 0xc0 is
translated to a priority of 0, not something we want, overriding the
"7" priority which was set previously explicitely. To avoid that, just
move setting priority later in the code.
A filter should log messages only if executed explicitly (e.g., during
route export or route import). When a filter is executed for technical
reasons (e.g., to establish whether a route was exported before), it
should run silently.
projects / thirdparty / bird.git / log
