"iw dev wlp2s0 station dump" shows incorrect rx bitrate:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 86.7 MBit/s VHT-MCS 9 VHT-NSS 1
This is because the RX band width is calculated incorrectly. Fix the
calculation according to the phydm_rxsc_2_bw() function from the
official drivers.
After:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 390.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 1
It also works correctly with the AP configured for 20 MHz and 40 MHz.
Remove VID/PID 0bda:c82c as it was inadvertently added to the device
list in driver rtw8821cu. This VID/PID is for the rtw8822cu device
and it is already in the appropriate place for that device.
netif_txq_maybe_stop() returns -1, 0, or 1, while
idpf_tx_maybe_stop_common() says it returns 0 or -EBUSY. As a result,
there sometimes are Tx queue timeout warnings despite that the queue
is empty or there is at least enough space to restart it.
Make idpf_tx_maybe_stop_common() inline and returning true or false,
handling the return of netif_txq_maybe_stop() properly. Use a correct
goto in idpf_tx_maybe_stop_splitq() to avoid stopping the queue or
incrementing the stops counter twice.
Fixes: 6818c4d5b3c2 ("idpf: add splitq start_xmit") Fixes: a5ab9ee0df0b ("idpf: add singleq start_xmit and napi poll") Cc: stable@vger.kernel.org # 6.7+ Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 75258f20fb70 ("btrfs: subpage: dump extra subpage bitmaps for
debug") an internal macro GET_SUBPAGE_BITMAP() is introduced to grab the
bitmap of each attribute.
But that commit is using bitmap_cut() which will do the left shift of
the larger bitmap, causing incorrect values.
Thankfully this bitmap_cut() is only called for debug usage, and so far
it's not yet causing problem.
Fix it to use bitmap_read() to only grab the desired sub-bitmap.
Fixes: 75258f20fb70 ("btrfs: subpage: dump extra subpage bitmaps for debug") CC: stable@vger.kernel.org # 6.6+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pt_event_snapshot_aux() uses pt->handle_nmi to determine if tracing
needs to be stopped, however tracing can still be going because
pt->handle_nmi is set to zero before tracing is stopped in pt_event_stop,
whereas pt_event_snapshot_aux() requires that tracing must be stopped in
order to copy a sample of trace from the buffer.
Instead call pt_config_stop() always, which anyway checks config for
RTIT_CTL_TRACEEN and does nothing if it is already clear.
Note pt_event_snapshot_aux() can continue to use pt->handle_nmi to
determine if the trace needs to be restarted afterwards.
The BPF subsystem may capture LBR data on a counting event. However, the
current implementation assumes that LBR can/should only be used with
sampling events.
For instance, retsnoop tool ([0]) makes an extensive use of this
functionality and sets up perf event as follows:
To limit the LBR for a sampling event is to avoid unnecessary branch
stack setup for a counting event in the sample read. Because LBR is only
read in the sampling event's overflow.
Although in most cases LBR is used in sampling, there is no HW limit to
bind LBR to the sampling mode. Allow an LBR setup for a counting event
unless in the sample read mode.
common_interrupt() and related variants call kvm_set_cpu_l1tf_flush_l1d(),
which is neither marked noinstr nor __always_inline.
So compiler puts it out of line and adds instrumentation to it. Since the
call is inside of instrumentation_begin/end(), objtool does not warn about
it.
The manifestation is that KCOV produces spurious coverage in
kvm_set_cpu_l1tf_flush_l1d() in random places because the call happens when
preempt count is not yet updated to say that the kernel is in an interrupt.
Mark kvm_set_cpu_l1tf_flush_l1d() as __always_inline and move it out of the
instrumentation_begin/end() section. It only calls __this_cpu_write()
which is already safe to call in noinstr contexts.
Fixes: 6368558c3710 ("x86/entry: Provide IDTENTRY_SYSVEC") Signed-off-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexander Potapenko <glider@google.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/3f9a1de9e415fcb53d07dc9e19fa8481bb021b1b.1718092070.git.dvyukov@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses 'use_acpi = true' in C-state custom table for all Xeon
platforms. The meaning of this flag is as follows.
1. If a C-state from the custom table is defined in ACPI _CST (matched
by the mwait hint), then enable this C-state.
2. Otherwise, disable this C-state, unless the C-sate definition in the
custom table has the 'CPUIDLE_FLAG_ALWAYS_ENABLE' flag set, in which
case enabled it.
The goal is to honor BIOS C6 settings - If BIOS disables C6, disable it
by default in the OS too (but it can be enabled via sysfs).
This works well on Xeons that expose only one flavor of C6. This are all
Xeons except for the newest Granite Rapids (GNR) and Sierra Forest (SRF).
The problem
~~~~~~~~~~~
GNR and SRF have 2 flavors of C6: C6/C6P on GNR, C6S/C6SP on SRF. The
the "P" flavor allows for the package C6, while the "non-P" flavor
allows only for core/module C6.
As far as this patch is concerned, both GNR and SRF platforms are
handled the same way. Therefore, further discussion is focused on GNR,
but it applies to SRF as well.
On Intel Xeon platforms, BIOS exposes only 2 ACPI C-states: C1 and C2.
Well, depending on BIOS settings, C2 may be named as C3. But there still
will be only 2 states - C1 and C3. But this is a non-essential detail,
so further discussion is focused on the ACPI C1 and C2 case.
On pre-GNR/SRF Xeon platforms, ACPI C1 is mapped to C1 or C1E, and ACPI
C2 is mapped to C6. The 'use_acpi' flag works just fine:
However, on GNR there are 2 flavors of C6, so BIOS maps ACPI C2 to
either C6 or C6P, depending on the user settings. As a result, due to
the 'use_acpi' flag, 'intel_idle' disables least one of the C6 flavors.
BIOS | OS | Verdict
----------------------------------------------------|---------
ACPI C2 disabled | C6 disabled, C6P disabled | OK
ACPI C2 mapped to C6 | C6 enabled, C6P disabled | Not OK
ACPI C2 mapped to C6P | C6 disabled, C6P enabled | Not OK
The goal of 'use_acpi' is to honor BIOS ACPI C2 disabled case, which
works fine. But if ACPI C2 is enabled, the goal is to enable all flavors
of C6, not just one of the flavors. This was overlooked when enabling
GNR/SRF platforms.
In other words, before GNR/SRF, the ACPI C2 status was binary - enabled
or disabled. But it is not binary on GNR/SRF, however the goal is to
continue treat it as binary.
The fix
~~~~~~~
Notice, that current algorithm matches ACPI and custom table C-states
by the mwait hint. However, mwait hint consists of the 'state' and
'sub-state' parts, and all C6 flavors have the same state value of 0x20,
but different sub-state values.
Introduce new C-state table flag - CPUIDLE_FLAG_PARTIAL_HINT_MATCH and
add it to both C6 flavors of the GNR/SRF platforms.
When matching ACPI _CST and custom table C-states, match only the start
part if the C-state has CPUIDLE_FLAG_PARTIAL_HINT_MATCH, other wise
match both state and sub-state parts (as before).
With this fix, GNR C-states enabled/disabled status looks like this.
The alternative would be to remove 'use_acpi' flag for GNR and SRF.
This would be a simpler solution, but it would violate the principle of
least surprise - users of Xeon platforms are used to the fact that
intel_idle honors C6 enabled/disabled flag. It is more consistent user
experience if GNR/SRF continue doing so.
How tested
~~~~~~~~~~
Tested on GNR and SRF platform with all the 3 BIOS configurations: ACPI
C2 disabled, mapped to C6/C6S, mapped to C6P/C6SP.
Tested on Ice lake Xeon and Sapphire Rapids Xeon platforms with ACPI C2
enabled and disabled, just to verify that the patch does not break older
Xeons.
Add Granite Rapids Xeon C-states, which are C1, C1E, C6, and C6P.
Comparing to previous Xeon Generations (e.g., Emerald Rapids), C6
requests end up only in core C6 state, and no package C-state promotion
takes place even if all cores in the package are in core C6.
C6P requests also end up in core C6, but if all cores have requested
C6P, the SoC will enter the package C6 state.
The TPM event log table is a Linux specific construct, where the data
produced by the GetEventLog() boot service is cached in memory, and
passed on to the OS using an EFI configuration table.
The use of EFI_LOADER_DATA here results in the region being left
unreserved in the E820 memory map constructed by the EFI stub, and this
is the memory description that is passed on to the incoming kernel by
kexec, which is therefore unaware that the region should be reserved.
Even though the utility of the TPM2 event log after a kexec is
questionable, any corruption might send the parsing code off into the
weeds and crash the kernel. So let's use EFI_ACPI_RECLAIM_MEMORY
instead, which is always treated as reserved by the E820 conversion
logic.
Internal documentation suggest that the TUXEDO Polaris 15 Gen5 AMD might
have GMxXGxX as the board name instead of GMxXGxx.
Adding both to be on the safe side.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Cc: All applicable <stable@vger.kernel.org> Link: https://patch.msgid.link/20240910094008.1601230-1-wse@tuxedocomputers.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Listed device need the override for the keyboard to work.
Fixes: 9946e39fe8d0 ("ACPI: resource: skip IRQ override on AMD Zen platforms") Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Li Chen <me@linux.beauty> Link: https://patch.msgid.link/87y15e6n35.wl-me@linux.beauty Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only buffer objects are valid return values of _STR.
If something else is returned description_show() will access invalid
memory.
Fixes: d1efe3c324ea ("ACPI: Add new sysfs interface to export device description") Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Link: https://patch.msgid.link/20240709-acpi-sysfs-groups-v2-1-058ab0667fa8@weissschuh.net Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the net_conf pointer is NULL and the code attempts to access its
fields without a check, it will lead to a null pointer dereference.
Add a NULL check before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The violation of atomicity occurs when the drbd_uuid_set_bm function is
executed simultaneously with modifying the value of
device->ldev->md.uuid[UI_BITMAP]. Consider a scenario where, while
device->ldev->md.uuid[UI_BITMAP] passes the validity check when its
value is not zero, the value of device->ldev->md.uuid[UI_BITMAP] is
written to zero. In this case, the check in drbd_uuid_set_bm might refer
to the old value of device->ldev->md.uuid[UI_BITMAP] (before locking),
which allows an invalid value to pass the validity check, resulting in
inconsistency.
To address this issue, it is recommended to include the data validity
check within the locked section of the function. This modification
ensures that the value of device->ldev->md.uuid[UI_BITMAP] does not
change during the validation process, thereby maintaining its integrity.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs to extract
function pairs that can be concurrently executed, and then analyzes the
instructions in the paired functions to identify possible concurrency
bugs including data races and atomicity violations.
Fixes: 9f2247bb9b75 ("drbd: Protect accesses to the uuid set with a spinlock") Cc: stable@vger.kernel.org Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com> Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com> Link: https://lore.kernel.org/r/20240913083504.10549-1-chenqiuji666@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of sev PLATFORM_STATUS failure, sev_get_api_version() fails
resulting in sev_data field of psp_master nulled out. This later becomes
a problem when unloading the ccp module because the device has not been
unregistered (via misc_deregister()) before clearing the sev_data field
of psp_master. As a result, on reloading the ccp module, a duplicate
device issue is encountered as can be seen from the dmesg log below.
on reloading ccp module via modprobe ccp
Call Trace:
<TASK>
dump_stack_lvl+0xd7/0xf0
dump_stack+0x10/0x20
sysfs_warn_dup+0x5c/0x70
sysfs_create_dir_ns+0xbc/0xd
kobject_add_internal+0xb1/0x2f0
kobject_add+0x7a/0xe0
? srso_alias_return_thunk+0x5/0xfbef5
? get_device_parent+0xd4/0x1e0
? __pfx_klist_children_get+0x10/0x10
device_add+0x121/0x870
? srso_alias_return_thunk+0x5/0xfbef5
device_create_groups_vargs+0xdc/0x100
device_create_with_groups+0x3f/0x60
misc_register+0x13b/0x1c0
sev_dev_init+0x1d4/0x290 [ccp]
psp_dev_init+0x136/0x300 [ccp]
sp_init+0x6f/0x80 [ccp]
sp_pci_probe+0x2a6/0x310 [ccp]
? srso_alias_return_thunk+0x5/0xfbef5
local_pci_probe+0x4b/0xb0
work_for_cpu_fn+0x1a/0x30
process_one_work+0x203/0x600
worker_thread+0x19e/0x350
? __pfx_worker_thread+0x10/0x10
kthread+0xeb/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c/0x60
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
kobject: kobject_add_internal failed for sev with -EEXIST, don't try to register things with the same name in the same directory.
ccp 0000:22:00.1: sev initialization failed
ccp 0000:22:00.1: psp initialization failed
ccp 0000:a2:00.1: no command queues available
ccp 0000:a2:00.1: psp enabled
Address this issue by unregistering the /dev/sev before clearing out
sev_data in case of PLATFORM_STATUS failure.
The qcom-rng driver supports both ACPI and device tree-based systems.
ACPI support was broken when the hw_random interface support was added.
Let's go ahead and fix this by adding the appropriate driver data to the
ACPI match table, and change the of_device_get_match_data() call to
device_get_match_data() so that it will also work on ACPI-based systems.
This fix was boot tested on a Qualcomm Amberwing server (ACPI based) and
on a Qualcomm SA8775p Automotive Development Board (DT based). I also
verified that qcom-rng shows up in /proc/crypto on both systems.
Commit 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
addressed an issue with stalled tx after the console code interrupted
the last bytes of a tx command by reenabling the watermark interrupt if
there is data in write buffer. This can however break software flow
control by re-enabling tx after the user has stopped it.
Address the original issue by not clearing the CMD_DONE flag after
polling for command completion. This allows the interrupt handler to
start another transfer when the CMD_DONE interrupt has not been disabled
due to flow control.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP") Fixes: 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang") Cc: stable@vger.kernel.org # 4.17 Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240906131336.23625-3-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qcom_geni_serial_poll_bit() can be used to wait for events like
command completion and is supposed to wait for the time it takes to
clear a full fifo before timing out.
As noted by Doug, the current implementation does not account for start,
stop and parity bits when determining the timeout. The helper also does
not currently account for the shift register and the two-word
intermediate transfer register.
A too short timeout can specifically lead to lost characters when
waiting for a transfer to complete as the transfer is cancelled on
timeout.
Instead of determining the poll timeout on every call, store the fifo
timeout when updating it in set_termios() and make sure to take the
shift and intermediate registers into account. Note that serial core has
already added a 20 ms margin to the fifo timeout.
Also note that the current uart_fifo_timeout() interface does
unnecessary calculations on every call and did not exist in earlier
kernels so only store its result once. This facilitates backports too as
earlier kernels can derive the timeout from uport->timeout, which has
since been removed.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP") Cc: stable@vger.kernel.org # 4.17 Reported-by: Douglas Anderson <dianders@chromium.org> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240906131336.23625-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI xHC host should be stopped and xhci driver memory freed before putting
host to PCI D3 state during PCI remove callback.
Hosts with XHCI_SPURIOUS_WAKEUP quirk did this the wrong way around
and set the host to D3 before calling usb_hcd_pci_remove(dev), which will
access the host to stop it, and then free xhci.
Coverity reports (as CID 1536978) that uart_poll_init() passes
uninitialized pm_state to uart_change_pm(). It is in case the first 'if'
takes the true branch (does "goto out;").
Fix this and simplify the function by simple guard(mutex). The code
needs no labels after this at all. And it is pretty clear that the code
has not fiddled with pm_state at that point.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Fixes: 5e227ef2aa38 (serial: uart_poll_init() should power on the UART) Cc: stable@vger.kernel.org Cc: Douglas Anderson <dianders@chromium.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20240805102046.307511-4-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa451 ("serial: rp2: New driver for Comtrol RocketPort 2 cards") Cc: stable <stable@kernel.org> Suggested-by: Jim Quinlan <james.quinlan@broadcom.com> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most firmware names are hardcoded strings, or are constructed from fairly
constrained format strings where the dynamic parts are just some hex
numbers or such.
However, there are a couple codepaths in the kernel where firmware file
names contain string components that are passed through from a device or
semi-privileged userspace; the ones I could find (not counting interfaces
that require root privileges) are:
- lpfc_sli4_request_firmware_update() seems to construct the firmware
filename from "ModelName", a string that was previously parsed out of
some descriptor ("Vital Product Data") in lpfc_fill_vpd()
- nfp_net_fw_find() seems to construct a firmware filename from a model
name coming from nfp_hwinfo_lookup(pf->hwinfo, "nffw.partno"), which I
think parses some descriptor that was read from the device.
(But this case likely isn't exploitable because the format string looks
like "netronome/nic_%s", and there shouldn't be any *folders* starting
with "netronome/nic_". The previous case was different because there,
the "%s" is *at the start* of the format string.)
- module_flash_fw_schedule() is reachable from the
ETHTOOL_MSG_MODULE_FW_FLASH_ACT netlink command, which is marked as
GENL_UNS_ADMIN_PERM (meaning CAP_NET_ADMIN inside a user namespace is
enough to pass the privilege check), and takes a userspace-provided
firmware name.
(But I think to reach this case, you need to have CAP_NET_ADMIN over a
network namespace that a special kind of ethernet device is mapped into,
so I think this is not a viable attack path in practice.)
Fix it by rejecting any firmware names containing ".." path components.
For what it's worth, I went looking and haven't found any USB device
drivers that use the firmware loader dangerously.
Cc: stable@vger.kernel.org Reviewed-by: Danilo Krummrich <dakr@kernel.org> Fixes: abb139e75c2c ("firmware: teach the kernel to load firmware files directly from the filesystem") Signed-off-by: Jann Horn <jannh@google.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20240828-firmware-traversal-v3-1-c76529c63b5f@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Foxconn uses a unique firmware for their MHI based modems. So the generic
firmware from Qcom won't work. Hence, update the EDL firmware path to
include the 'foxconn' subdirectory based on the modem SoC so that the
Foxconn specific firmware could be used.
Respective firmware will be upstreamed to linux-firmware repo.
Cc: stable@vger.kernel.org # 6.11 Fixes: bf30a75e6e00 ("bus: mhi: host: Add support for Foxconn SDX72 modems") Signed-off-by: Slark Xiao <slark_xiao@163.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20240725022941.65948-1-slark_xiao@163.com
[mani: Reworded the subject and description] Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2_handle_usb_suspend_intr() function disables gadget clocks in USB
peripheral mode when no other power-down mode is available (introduced by
commit 0112b7ce68ea ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")).
However, the dwc2_drd_role_sw_set() USB role update handler attempts to
read DWC2 registers if the USB role has changed while the USB is in suspend
mode (when the clocks are gated). This causes the system to hang.
Release the gadget clocks before handling the USB role update.
Fixes: 0112b7ce68ea ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.") Cc: stable@vger.kernel.org Signed-off-by: Tomas Marek <tomas.marek@elrest.cz> Link: https://lore.kernel.org/r/20240906055025.25057-1-tomas.marek@elrest.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a7f3813e589f ("usb: gadget: dummy_hcd: Switch to hrtimer transfer
scheduler") switched dummy_hcd to use hrtimer and made the timer's
callback be executed in the hardirq context.
With that change, __usb_hcd_giveback_urb now gets executed in the hardirq
context, which causes problems for KCOV and KMSAN.
One problem is that KCOV now is unable to collect coverage from
the USB code that gets executed from the dummy_hcd's timer callback,
as KCOV cannot collect coverage in the hardirq context.
Another problem is that the dummy_hcd hrtimer might get triggered in the
middle of a softirq with KCOV remote coverage collection enabled, and that
causes a WARNING in KCOV, as reported by syzbot. (I sent a separate patch
to shut down this WARNING, but that doesn't fix the other two issues.)
Finally, KMSAN appears to ignore tracking memory copying operations
that happen in the hardirq context, which causes false positive
kernel-infoleaks, as reported by syzbot.
Change the hrtimer in dummy_hcd to execute the callback in the softirq
context.
The resume operation of Phytium Px210 xHCI host would failed
to restore state. Use the XHCI_RESET_ON_RESUME quirk to skip
it and reset the controller after resume.
Fix changes incorrect usb_request->status returned during disabling
endpoints. Before fix the status returned during dequeuing requests
while disabling endpoint was ECONNRESET.
Patch change it to ESHUTDOWN.
Patch fixes issue detected during testing UVC gadget.
During stopping streaming the class starts dequeuing usb requests and
controller driver returns the -ECONNRESET status. After completion
requests the class or application "uvc-gadget" try to queue this
request again. Changing this status to ESHUTDOWN cause that UVC assumes
that endpoint is disabled, or device is disconnected and stops
re-queuing usb requests.
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
TIOCGSERIAL is an ioctl. Thus it must be atomic. It returns
two values. Racing with set_serial it can return an inconsistent
result. The mutex must be taken.
In terms of logic the bug is as old as the driver. In terms of
code it goes back to the conversion to the get_serial and
set_serial methods.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@kernel.org> Fixes: 99f75a1fcd865 ("cdc-acm: switch to ->[sg]et_serial()") Link: https://lore.kernel.org/r/20240912141916.1044393-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a small window during probing when IO is running
but the backlight is not registered. Processing events
during that time will crash. The completion handler
needs to check for a backlight before scheduling work.
The work can submit URBs and the URBs can schedule the work.
This cycle needs to be broken, when a device is to be stopped.
Use a flag to do so.
This is a design issue as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") CC: stable@vger.kernel.org Link: https://patch.msgid.link/20240919123525.688065-1-oneukum@suse.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All USB devices supported by rtw88 have the same problem: they don't
transmit beacons in AP mode. (Some?) SDIO devices are also affected.
The cause appears to be clearing BIT_EN_BCNQ_DL of REG_FWHW_TXQ_CTRL
before uploading the beacon reserved page, so don't clear the bit for
USB and SDIO devices.
Remove the CAN_CTRLMODE_3_SAMPLES announcement for CAN-USB/3-FD devices
because these devices don't support it.
The hardware has a Microchip SAM E70 microcontroller that uses a Bosch
MCAN IP core as CAN FD controller. But this MCAN core doesn't support
triple sampling.
Fixes: 80662d943075 ("can: esd_usb: Add support for esd CAN-USB/3") Cc: stable@vger.kernel.org Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://patch.msgid.link/20240904222740.2985864-2-stefan.maetje@esd.eu Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SD cards can produce write latency spikes on the order of a hundred
milliseconds. If the target firmware does not hide that latency during DATA
IN and OUT phases it can cause the PDMA circuitry to raise a processor bus
fault which in turn leads to an unreliable byte count and a DMA overrun.
The Last Byte Sent flag is used to detect the overrun but this mechanism is
unreliable on some systems. Instead, set a DID_ERROR result whenever there
is a bus fault during a PDMA send, unless the cause was a phase mismatch.
Cc: stable@vger.kernel.org # 5.15+ Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Fixes: 7c1f3e3447a1 ("scsi: mac_scsi: Treat Last Byte Sent time-out as failure") Signed-off-by: Finn Thain <fthain@linux-m68k.org> Link: https://lore.kernel.org/r/cc38df687ace2c4ffc375a683b2502fc476b600d.1723001788.git.fthain@linux-m68k.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the error handling can be revised, some preparation is needed.
Refactor the polling loop with a new function, macscsi_wait_for_drq().
This function will gain more call sites in the next patch.
After a bus fault, capture and log the chip registers immediately, if the
NDEBUG_PSEUDO_DMA macro is defined. Remove some printk(KERN_DEBUG ...)
messages that aren't needed any more. Don't skip the debug message when
bytes == 0. Show all of the byte counters in the debug messages.
An older generation of HBAs are failing FCP discovery due to usage of an
outdated field in FCP command WQEs.
Fix by checking the SLI Interface Type register for applicable support of
32 Byte CDB commands, and restore a setting for a WQE path using normal 16
byte CDBs.
Fixes: af20bb73ac25 ("scsi: lpfc: Add support for 32 byte CDBs") Cc: stable@vger.kernel.org # v6.10+ Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20240912232447.45607-4-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8db8f6ce556a ("scsi: ufs: qcom: Add missing interconnect bandwidth
values for Gear 5") updated the ufs_qcom_bw_table for Gear 5. However, it
missed updating the cfg_bw value for the max mode.
Hence update the cfg_bw value for the max mode for UFS 4.x devices.
Ff the device returns page 0xb1 with length 8 (happens with qemu v2.x, for
example), sd_read_block_characteristics() may attempt an out-of-bounds
memory access when accessing the zoned field at offset 8.
Fixes: 7fb019c46eee ("scsi: sd: Switch to using scsi_device VPD pages") Cc: stable@vger.kernel.org Signed-off-by: Martin Wilck <mwilck@suse.com> Link: https://lore.kernel.org/r/20240912134308.282824-1-mwilck@suse.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user requests the ALL_SUB_MPAGES mode sense page,
ata_msense_control() adds the CDL_T2A_SUB_MPAGE twice instead of adding
the CDL_T2A_SUB_MPAGE and CDL_T2B_SUB_MPAGE pages information. Correct
the second call to ata_msense_control_spgt2() to report the
CDL_T2B_SUB_MPAGE page.
Fixes: 673b2fe6ff1d ("scsi: ata: libata-scsi: Add support for CDL pages mode sense") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Windows client write with FILE_APPEND_DATA when using git.
ksmbd should allow write it with this flags.
Z:\test>git commit -m "test"
fatal: cannot update the ref 'HEAD': unable to append to
'.git/logs/HEAD': Bad file descriptor
Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Cc: stable@vger.kernel.org # v5.15+ Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some file systems may not provide dot (.) and dot-dot (..) as they are
optional in POSIX. ksmbd can misjudge emptiness of a directory in those
file systems, since it assumes there are always at least two entries:
dot and dot-dot.
Just don't count dot and dot-dot.
Cc: stable@vger.kernel.org # v6.1+ Signed-off-by: Hobin Woo <hobin.woo@samsung.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'ld' and 'std' instructions require a 4-byte aligned displacement
because they are DS-form instructions. But the "m" asm constraint
doesn't enforce that.
That can lead to build errors if the compiler chooses a non-aligned
displacement, as seen with GCC 14:
/tmp/ccuSzwiR.s: Assembler messages:
/tmp/ccuSzwiR.s:2579: Error: operand out of domain (39 is not a multiple of 4)
make[5]: *** [scripts/Makefile.build:229: net/core/page_pool.o] Error 1
Dumping the generated assembler shows:
ld 8,39(8) # MEM[(const struct atomic64_t *)_29].counter, t
Use the YZ constraints to tell the compiler either to generate a DS-form
displacement, or use an X-form instruction, either of which prevents the
build error.
See commit 2d43cc701b96 ("powerpc/uaccess: Fix build errors seen with
GCC 13/14") for more details on the constraint letters.
Fixes: 9f0cbea0d8cc ("[POWERPC] Implement atomic{, 64}_{read, write}() without volatile") Cc: stable@vger.kernel.org # v2.6.24+ Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Closes: https://lore.kernel.org/all/20240913125302.0a06b4c7@canb.auug.org.au Tested-by: Mina Almasry <almasrymina@google.com> Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240916120510.2017749-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In find_asymmetric_key(), if all NULLs are passed in the id_{0,1,2}
arguments, the kernel will first emit WARN but then have an oops
because id_2 gets dereferenced anyway.
Add the missing id_2 check and move WARN_ON() to the final else branch
to avoid duplicate NULL checks.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
Cc: stable@vger.kernel.org # v5.17+ Fixes: 7d30198ee24f ("keys: X.509 public key issuer lookup without AKID") Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Roman Smirnov <r.smirnov@omp.ru> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TDX only supports kernel-initiated MMIO operations. The handle_mmio()
function checks if the #VE exception occurred in the kernel and rejects
the operation if it did not.
However, userspace can deceive the kernel into performing MMIO on its
behalf. For example, if userspace can point a syscall to an MMIO address,
syscall does get_user() or put_user() on it, triggering MMIO #VE. The
kernel will treat the #VE as in-kernel MMIO.
Ensure that the target MMIO address is within the kernel before decoding
instruction.
After commit a0f7085f6a63 ("LoongArch: Add RANDOMIZE_KSTACK_OFFSET
support"), there are three new instructions "addi.d $fp, $sp, 32",
"sub.d $sp, $sp, $t0" and "addi.d $sp, $fp, -32" for the secondary
stack in do_syscall(), then there is a objtool warning "return with
modified stack frame" and no handle_syscall() which is the previous
frame of do_syscall() in the call trace when executing the command
"echo l > /proc/sysrq-trigger".
The instruction "sub.d $sp, $sp, $t0" changes the stack bottom and the
new stack size is a random value, in order to find the return address of
do_syscall() which is stored in the original stack frame after executing
"jirl $ra, $t0, 0", it should use fp which points to the original stack
top.
At the beginning, the thought is tended to decode the secondary stack
instruction "sub.d $sp, $sp, $t0" and set it as a label, then check this
label for the two frame pointer instructions to change the cfa base and
cfa offset during the period of secondary stack in update_cfi_state().
This is valid for GCC but invalid for Clang due to there are different
secondary stack instructions for ClangBuiltLinux on LoongArch, something
like this:
Actually, it equals to a single instruction "sub.d $sp, $sp, $a0", but
there is no proper condition to check it as a label like GCC, and so the
beginning thought is not a good way.
Essentially, there are two special frame pointer instructions which are
"addi.d $fp, $sp, imm" and "addi.d $sp, $fp, imm", the first one points
fp to the original stack top and the second one restores the original
stack bottom from fp.
Based on the above analysis, in order to avoid adding an arch-specific
update_cfi_state(), we just add a member "frame_pointer" in the "struct
symbol" as a label to avoid affecting the current normal case, then set
it as true only if there is "addi.d $sp, $fp, imm". The last is to check
this label for the two frame pointer instructions to change the cfa base
and cfa offset in update_cfi_state().
Tested with the following two configs:
(1) CONFIG_RANDOMIZE_KSTACK_OFFSET=y &&
CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT=n
(2) CONFIG_RANDOMIZE_KSTACK_OFFSET=y &&
CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT=y
By the way, there is no effect for x86 with this patch, tested on the
x86 machine with Fedora 40 system.
[WHY]
RCG state of IPX in idle is more stable for DCN351 and some variants of
DCN35 than IPS2.
[HOW]
Rework dm_get_default_ips_mode() to specify default per ASIC and update
DCN35/DCN351 defaults accordingly.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Sun peng Li <sunpeng.li@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY & HOW]
When underscan is set through xrandr, it causes the stream destination
rect to change in a way it becomes complicated to handle the calculations
for subvp. Since this is a corner case, disable subvp when underscan is
set.
Fix the existing check that is supposed to catch this corner case by
adding a check based on the parameters in the stream
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Dillon Varone <dillon.varone@amd.com> Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
It makes DSC enable when we commit the stream which need
keep power off, and then it will skip to disable DSC if
pipe reset at this situation as power has been off. It may
cause the DSC unexpected enable on the pipe with the
next new stream which doesn't support DSC.
[HOW]
Check the DSC used on current pipe status when update stream.
Skip to enable if it has been off. The operation enable
DSC should happen when set power on.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
Corrupted screen will be observed when 4k144 DP/HDMI display and
4k144 eDP are connected, changing eDP refresh rate from 60Hz to 144Hz.
[HOW]
override_det_buffer_size_kbytes should be true for DCN35/DCN351.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Roman Li <roman.li@amd.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Yihan Zhu <Yihan.Zhu@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
Hangs with Z8 can occur if running an older unfixed PMFW version.
[HOW]
Fallback to RCG only for dynamic IPS2 states if it's not newer than
93.12. Limit to DCN35.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Charlene Liu <charlene.liu@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY & HOW]
On display on sequence, enabling SYMCLK32_LE root clock gating
causes issue in link training so disabling it is needed.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently amdgpu takes backlight caps provided by the ACPI tables
on systems as is. If the firmware sets maximums that are too low
this means that users don't get a good experience.
To avoid having to maintain a quirk list of such systems, do a sanity
check on the values. Check that the spread is at least half of the
values that amdgpu would use if no ACPI table was found and if not
use the amdgpu defaults.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3020 Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
DSC on eDP could be enabled during VBIOS post. The enabled
DSC may not be disabled when enter to OS, once the system was
in second screen only mode before entering to S4. In this
case, OS will not send setTimings to reset eDP path again.
The enabled DSC HW will make a new stream without DSC cannot
output normally if it reused this pipe with enabled DSC.
[HOW]
In accelerated mode, to clean up DSC blocks if eDP is on link
but not active when we are not in fast boot and seamless boot.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Charlene Liu <charlene.liu@amd.com> Signed-off-by: Martin Tsai <martin.tsai@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
The calculated vtotal may has 1 line deviation. To get precisely
vtotal number, round the vtotal result.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Anthony Koo <anthony.koo@amd.com> Signed-off-by: Robin Chen <robin.chen@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY && HOW]
For some HDMI OVT timing, YCbCr422 encoding fails at the DSC
bandwidth check. The root cause is our DSC policy for timing
doesn't account for HDMI YCbCr422 native support.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Chris Park <chris.park@amd.com> Signed-off-by: Leo Ma <hanghong.ma@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move enable_doorbell_selfring_aperture from common_hw_init
to common_late_init in soc24, otherwise selfring aperture is
initialized with an incorrect doorbell aperture base.
Port changes from this commit from soc21 to soc24:
commit 1c312e816c40 ("drm/amdgpu: Enable doorbell selfring after resize FB BAR")
Signed-off-by: David Belanger <david.belanger@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 6.11.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without setting dcc bit, there is ramdon PTE copy corruption on sdma 7.
so add this bit and update the packet format accordingly.
Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Frank Min <Frank.Min@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 6.11.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[how]
dsc recompute should be skipped if no mode change detected on the new
request. If detected, keep checking whether the stream is already on
current state or not.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a dedicated mutex to guard kvm_usage_count to fix a potential deadlock
on x86 due to a chain of locks and SRCU synchronizations. Translating the
below lockdep splat, CPU1 #6 will wait on CPU0 #1, CPU0 #8 will wait on
CPU2 #3, and CPU2 #7 will wait on CPU1 #4 (if there's a writer, due to the
fairness of r/w semaphores).
Note, there are likely more potential deadlocks in KVM x86, e.g. the same
pattern of taking cpu_hotplug_lock outside of kvm_lock likely exists with
__kvmclock_cpufreq_notifier():
But, actually triggering such deadlocks is beyond rare due to the
combination of dependencies and timings involved. E.g. the cpufreq
notifier is only used on older CPUs without a constant TSC, mucking with
the NX hugepage mitigation while VMs are running is very uncommon, and
doing so while also onlining/offlining a CPU (necessary to generate
contention on cpu_hotplug_lock) would be even more unusual.
The most robust solution to the general cpu_hotplug_lock issue is likely
to switch vm_list to be an RCU-protected list, e.g. so that x86's cpufreq
notifier doesn't to take kvm_lock. For now, settle for fixing the most
blatant deadlock, as switching to an RCU-protected list is a much more
involved change, but add a comment in locking.rst to call out that care
needs to be taken when walking holding kvm_lock and walking vm_list.
======================================================
WARNING: possible circular locking dependency detected
6.10.0-smp--c257535a0c9d-pip #330 Tainted: G S O
------------------------------------------------------
tee/35048 is trying to acquire lock: ff6a80eced71e0a8 (&kvm->slots_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x179/0x1e0 [kvm]
but task is already holding lock: ffffffffc07abb08 (kvm_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x14a/0x1e0 [kvm]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Re-introduce the "split" x2APIC ICR storage that KVM used prior to Intel's
IPI virtualization support, but only for AMD. While not stated anywhere
in the APM, despite stating the ICR is a single 64-bit register, AMD CPUs
store the 64-bit ICR as two separate 32-bit values in ICR and ICR2. When
IPI virtualization (IPIv on Intel, all AVIC flavors on AMD) is enabled,
KVM needs to match CPU behavior as some ICR ICR writes will be handled by
the CPU, not by KVM.
Add a kvm_x86_ops knob to control the underlying format used by the CPU to
store the x2APIC ICR, and tune it to AMD vs. Intel regardless of whether
or not x2AVIC is enabled. If KVM is handling all ICR writes, the storage
format for x2APIC mode doesn't matter, and having the behavior follow AMD
versus Intel will provide better test coverage and ease debugging.
Hoist kvm_x2apic_icr_write() above kvm_apic_write_nodecode() so that a
local helper to _read_ the x2APIC ICR can be added and used in the
nodecode path without needing a forward declaration.
Inject a #GP on a WRMSR(ICR) that attempts to set any reserved bits that
are must-be-zero on both Intel and AMD, i.e. any reserved bits other than
the BUSY bit, which Intel ignores and basically says is undefined.
KVM's xapic_state_test selftest has been fudging the bug since commit 4b88b1a518b3 ("KVM: selftests: Enhance handling WRMSR ICR register in
x2APIC mode"), which essentially removed the testcase instead of fixing
the bug.
WARN if the nodecode path triggers a #GP, as the CPU is supposed to check
reserved bits for ICR when it's partially virtualized.
When we share memory through FF-A and the description of the buffers
exceeds the size of the mapped buffer, the fragmentation API is used.
The fragmentation API allows specifying chunks of descriptors in subsequent
FF-A fragment calls and no upper limit has been established for this.
The entire memory region transferred is identified by a handle which can be
used to reclaim the transferred memory.
To be able to reclaim the memory, the description of the buffers has to fit
in the ffa_desc_buf.
Add a bounds check on the FF-A sharing path to prevent the memory reclaim
from failing.
Also do_ffa_mem_xfer() does not need __always_inline, except for the
BUILD_BUG_ON() aspect, which gets moved to a macro.
[maz: fixed the BUILD_BUG_ON() breakage with LLVM, thanks to Wei-Lin Chang
for the timely report]
Fixes: 634d90cf0ac65 ("KVM: arm64: Handle FFA_MEM_LEND calls from the host") Cc: stable@vger.kernel.org Reviewed-by: Sebastian Ene <sebastianene@google.com> Signed-off-by: Snehal Koukuntla <snehalreddy@google.com> Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20240909180154.3267939-1-snehalreddy@google.com Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Gen6 devices have the same problem and the same Solution as the Gen5
ones.
Some TongFang barebones have touchpad and/or keyboard issues after
suspend, fixable with nomux + reset + noloop + nopnp. Luckily, none of
them have an external PS/2 port so this can safely be set for all of
them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
Some TongFang barebones have touchpad and/or keyboard issues after
suspend, fixable with nomux + reset + noloop + nopnp. Luckily, none of
them have an external PS/2 port so this can safely be set for all of
them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
During adp5588_setup(), we read all the events to clear the event FIFO.
However, adp5588_read() just calls i2c_smbus_read_byte_data() which
returns the byte read in case everything goes well. Hence, we need to
explicitly check for a negative error code instead of checking for
something different than 0.
Fixes: e960309ce318 ("Input: adp5588-keys - bail out on returned error") Cc: stable@vger.kernel.org Signed-off-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20240920-fix-adp5588-err-check-v1-1-81f6e957ef24@analog.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace can supply an iova and uptr such that the target iova alignment
becomes really big and ALIGN() overflows which corrupts the selected area
range during allocation. CONFIG_IOMMUFD_TEST can detect this:
Cap the automatic alignment to the huge page size, which is probably a
better idea overall. Huge automatic alignments can fragment and chew up
the available IOVA space without any reason.
Link: https://patch.msgid.link/r/0-v1-8009738b9891+1f7-iommufd_align_overflow_jgg@nvidia.com Cc: stable@vger.kernel.org Fixes: 51fe6141f0f6 ("iommufd: Data structure to provide IOVA to PFN mapping") Reviewed-by: Nicolin Chen <nicolinc@nvidia.com> Reported-by: syzbot+16073ebbc4c64b819b47@syzkaller.appspotmail.com Closes: https://lore.kernel.org/r/000000000000388410061a74f014@google.com Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An incorrect argument order calling amd_iommu_dev_flush_pasid_pages()
causes improper flushing of the IOMMU, leaving the old value of GCR3 from
a previous process attached to the same PASID.
As Fedor Pchelkin pointed out, this commit violates the
convention of using the macro return value, which causes errors.
For example, in functions tda18271_attach(), xc5000_attach(),
simple_tuner_attach().
Link: https://lore.kernel.org/linux-media/20240424202031.syigrtrtipbq5f2l@fpc/ Suggested-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Roman Smirnov <r.smirnov@omp.ru> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRNSYNC feature is available (and enabled) only in transparent mode.
Since commit 7cc9bda9c163 ("soc: fsl: cpm1: qmc: Handle timeslot entries
at channel start() and stop()") TRNSYNC register is updated in
transparent and hdlc mode. In hdlc mode, the address of the TRNSYNC
register is used by the QMC for other internal purpose. Even if no weird
results were observed in hdlc mode, touching this register in this mode
is wrong.
Return devm_of_clk_add_hw_provider() in order to transfer the error, if it
fails due to resource allocation failure or device tree clock provider
registration failure.
Cc: stable@vger.kernel.org Fixes: ebbfabc16d23 ("ASoC: rt5682: Add CCF usage for providing I2S clks") Signed-off-by: Ma Ke <make24@iscas.ac.cn> Link: https://patch.msgid.link/20240830143154.3448004-1-make24@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rpm_requests device nodes have the compatible node. As such the
rpmsg core uses OF modalias instead of a native rpmsg modalias. Thus if
smd-rpm is built as a module, it doesn't get autoloaded for the device.
Revert the commit bcabe1e09135 ("soc: qcom: smd-rpm: Match rpmsg channel
instead of compatible")
projects / thirdparty / kernel / stable.git / log
