They uses the codec ALC255, and have the different pin cfg definition
from the ones in the existing pin quirk table. Now adding them into
the table to fix the problem.
ASRock B150M Pro4/D3 mobo with ALC892 codec doesn't seem to provide
proper pins for the surround outputs, hence we need to specify the
pincfgs manually with a couple of other corrections.
We have a new Dell laptop model which uses ALC295, the pin definition
is different from the existing ones in the pin quirk table, to fix the
headset mic detection and mic mute led's problem, we need to add the
new pin defintion into the pin quirk table.
Commit 49d9e77e72cf ("ALSA: hda - Fix system panic when DMA > 40 bits
for Nvidia audio controllers") simply disabled any DMA exceeding 32
bits for NVidia devices, even though they are capable of performing
DMA up to 40 bits. On some architectures (such as arm64), system memory
is not guaranteed to be 32-bit addressable by PCI devices, and so this
change prevents NVidia devices from working on platforms such as AMD
Seattle.
Since the original commit already mentioned that up to 40 bits of DMA
is supported, and given that the code has been updated in the meantime
to support a 40 bit DMA mask on other devices, revert commit 49d9e77e72cf
and explicitly set the DMA mask to 40 bits for NVidia devices.
The recent rewrite of the sequencer time accounting using timespec64
in the commit [3915bf294652: ALSA: seq_timer: use monotonic times
internally] introduced a bad regression. Namely, the time reported
back doesn't increase but goes back and forth.
The culprit was obvious: the delta is stored to the result (cur_time =
delta), instead of adding the delta (cur_time += delta)!
The stk1160 chip needs QUIRK_AUDIO_ALIGN_TRANSFER. This patch resolves
the issue reported on the mailing list
(http://marc.info/?l=linux-sound&m=139223599126215&w=2) and also fixes
bug 180071 (https://bugzilla.kernel.org/show_bug.cgi?id=180071).
We need to wait until the percpu_ref is released before exit. Otherwise,
we sometimes lose the race and trigger this new warning that was added
in v4.9 (commit a67823c1ed10 "percpu-refcount: init ->confirm_switch
member properly"):
Fixes: ab68f2622136 ("/dev/dax, pmem: direct access to persistent memory") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since BIG_KEYS can't be compiled as module it requires one of the "stdrng"
providers to be compiled into kernel. Otherwise big_key_crypto_init() fails
on crypto_alloc_rng step and next dereference of big_key_skcipher (e.g. in
big_key_preparse()) results in a NULL pointer dereference.
Fixes: 13100a72f40f5748a04017e0ab3df4cf27c809ef ('Security: Keys: Big keys stored encrypted') Signed-off-by: Artem Savkov <asavkov@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: Kirill Marinushkin <k.marinushkin@gmail.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
big_key has two separate initialisation functions, one that registers the
key type and one that registers the crypto. If the key type fails to
register, there's no problem if the crypto registers successfully because
there's no way to reach the crypto except through the key type.
However, if the key type registers successfully but the crypto does not,
big_key_rng and big_key_blkcipher may end up set to NULL - but the code
neither checks for this nor unregisters the big key key type.
Furthermore, since the key type is registered before the crypto, it is
theoretically possible for the kernel to try adding a big_key before the
crypto is set up, leading to the same effect.
Fix this by merging big_key_crypto_init() and big_key_init() and calling
the resulting function late. If they're going to be encrypted, we
shouldn't be creating big_keys before we have the facilities to do the
encryption available. The key type registration is also moved after the
crypto initialisation.
The fix also includes message printing on failure.
If the big_key type isn't correctly set up, simply doing:
dd if=/dev/zero bs=4096 count=1 | keyctl padd big_key a @s
ought to cause an oops.
Fixes: 13100a72f40f5748a04017e0ab3df4cf27c809ef ('Security: Keys: Big keys stored encrypted') Signed-off-by: David Howells <dhowells@redhat.com>
cc: Peter Hlavaty <zer0mem@yahoo.com>
cc: Kirill Marinushkin <k.marinushkin@gmail.com>
cc: Artem Savkov <asavkov@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a short sprintf buffer in proc_keys_show(). If the gcc stack protector
is turned on, this can cause a panic due to stack corruption.
The problem is that xbuf[] is not big enough to hold a 64-bit timeout
rendered as weeks:
(gdb) p 0xffffffffffffffffULL/(60*60*24*7)
$2 = 30500568904943
That's 14 chars plus NUL, not 11 chars plus NUL.
Expand the buffer to 16 chars.
I think the unpatched code apparently works if the stack-protector is not
enabled because on a 32-bit machine the buffer won't be overflowed and on a
64-bit machine there's a 64-bit aligned pointer at one side and an int that
isn't checked again on the other side.
Reported-by: Ondrej Kozina <okozina@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Ondrej Kozina <okozina@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initial logic for checking CPU match resulted in OR of CPU features
rather than the intended AND.
Updated to use boot_cpu_has macro rather than x86_match_cpu.
In addition, MWAIT is the only required CPU feature for idle
injection to work. Drop other feature requirements since they are
only needed for optimal efficiency.
Signed-off-by: Eric Ernst <eric.ernst@linux.intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 4.0, we saw a stack corruption from a page fault entering direct
memory cgroup reclaim, calling into btrfs_releasepage(), which then
tried to allocate an extent and recursed back into a kmem charge ad
nauseam:
On later kernels, kmem charging is opt-in rather than opt-out, and that
particular kmem allocation in btrfs_releasepage() is no longer being
charged and won't recurse and overrun the stack anymore.
But it's not impossible for an accounted allocation to happen from the
memcg direct reclaim context, and we needed to reproduce this crash many
times before we even got a useful stack trace out of it.
Like other direct reclaimers, mark tasks in memcg reclaim PF_MEMALLOC to
avoid recursing into any other form of direct reclaim. Then let
recursive charges from PF_MEMALLOC contexts bypass the cgroup limit.
Link: http://lkml.kernel.org/r/20161025141050.GA13019@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue is caused by kmemcg feature that try to create new set of
kmem_caches for each memcg. Recently, kmem_cache creation is slowed by
synchronize_sched() and futher kmem_cache creation is also delayed since
kmem_cache creation is synchronized by a global slab_mutex lock. So,
the number of kworker that try to create kmem_cache increases quietly.
synchronize_sched() is for lockless access to node's shared array but
it's not needed when a new kmem_cache is created. So, this patch rules
out that case.
Fixes: 801faf0db894 ("mm/slab: lockless decision to grow cache") Link: http://lkml.kernel.org/r/1475734855-4837-1-git-send-email-iamjoonsoo.kim@lge.com Reported-by: Doug Smythies <dsmythies@telus.net> Tested-by: Doug Smythies <dsmythies@telus.net> Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in https://bugzilla.kernel.org/show_bug.cgi?id=177821:
After some analysis it seems to be that the problem is in alloc_super().
In case list_lru_init_memcg() fails it goes into destroy_super(), which
calls list_lru_destroy().
And in list_lru_init() we see that in case memcg_init_list_lru() fails,
lru->node is freed, but not set NULL, which then leads list_lru_destroy()
to believe it is initialized and call memcg_destroy_list_lru().
memcg_destroy_list_lru() in turn can access lru->node[i].memcg_lrus,
which is NULL.
[akpm@linux-foundation.org: add comment] Signed-off-by: Alexander Polakov <apolyakov@beget.ru> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function xfs_calc_dquots_per_chunk takes a parameter in units
of basic blocks. The kernel seems to get the units wrong, but
userspace got 'fixed' by commenting out the unnecessary conversion.
Fix both.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating a new line handle or event a file is allocated that it is
associated to. The file is attached to a file descriptor of the current
process and the file descriptor is returned to userspace using
copy_to_user(). If this copy operation fails the line handle or event
allocation is aborted, all acquired resources are freed and an error is
returned.
But the file struct is not freed and left attached to the userspace
application and even though the file descriptor number was not copied it is
trivial to guess. If a userspace application performs a IOCTL on such a
left over file descriptor it will trigger a use-after-free and if the file
descriptor is closed (latest when the application exits) a double-free is
triggered.
anon_inode_getfd() performs 3 tasks, allocate a file struct, allocate a
file descriptor for the current process and install the file struct in the
file descriptor. As soon as the file struct is installed in the file
descriptor it is accessible by userspace (even if the IOCTL itself hasn't
completed yet), this means uninstalling the fd on the error path is not an
option, since userspace might already got a reference to the file.
Instead anon_inode_getfd() needs to be broken into its individual steps.
The allocation of the file struct and file descriptor is done first, then
the copy_to_user() is executed and only if it succeeds the file is
installed.
Since the file struct is reference counted it can not be just freed, but
its reference needs to be dropped, which will also call the release()
callback, which will free the state attached to the file. So in this case
the normal error cleanup path should not be taken.
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But only the
first element of the values array in the struct is set, which leaves the
struct partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO_GET_LINEEVENT_IOCTL currently ignores unknown or undefined
linehandle and lineevent flags. From a backwards and forwards compatibility
viewpoint it is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO_GET_LINEHANDLE_IOCTL currently ignores unknown or undefined
linehandle flags. From a backwards and forwards compatibility viewpoint it
is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But depending on
the number of requested line handles the struct is only partially
initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
The GPIO_GET_CHIPINFO_IOCTL handler allocates a gpiochip_info struct on the
stack and then passes it to copy_to_user(). But depending on the length of
the GPIO chip name and label the struct is only partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Fixes: 521a2ad6f862 ("gpio: add userspace ABI for GPIO line information") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current line offset validation is off by one. Depending on the data
stored behind the descs array this can either cause undefined behavior or
disclose arbitrary, potentially sensitive, memory to the issuing userspace
application.
Make sure that offset is within the bounds of the desc array.
Fixes: 521a2ad6f862 ("gpio: add userspace ABI for GPIO line information") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in commit f56141e3e2d9 ("all arches, signal: move restart_block to
struct task_struct"), all architectures and core code were changed to
use task_struct::restart_block. However, when h8300 support was
subsequently restored in v4.2, it was not updated to account for this,
and maintains thread_info::restart_block, which is not kept in sync.
This patch drops the redundant restart_block from thread_info, and moves
h8300 to the common one in task_struct, ensuring that syscall restarting
always works as expected.
Fixes: f56141e3e2d9 ("all arches, signal: move restart_block to struct task_struct") Link: http://lkml.kernel.org/r/1476714934-11635-1-git-send-email-mark.rutland@arm.com Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: uclinux-h8-devel@lists.sourceforge.jp Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instantiated SPI device nodes are marked with OF_POPULATE. This was
introduced in bd6c164. On unloading, loaded device nodes will of course
be unmarked. The problem are nodes that fail during initialisation: If a
node fails, it won't be unloaded and hence not be unmarked.
If a SPI driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Note that the same issue exists for I2C.
Fixes: bd6c164 ("spi: Mark instantiated device nodes with OF_POPULATE") Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we get a spurious interrupt in fsl_espi_irq, we end up
processing four uninitalized bytes of data, as shown in this
warning message:
drivers/spi/spi-fsl-espi.c: In function 'fsl_espi_irq':
drivers/spi/spi-fsl-espi.c:462:4: warning: 'rx_data' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds another check so we skip the data in this case.
Fixes: 6319a68011b8 ("spi/fsl-espi: avoid infinite loops on fsl_espi_cpu_irq()") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i2c adapter is only relevant for some peer device types, so
let's clear the pdt if it's still the same as the old_pdt when we
tear down the i2c adapter.
I don't really like this design pattern of updating port->whatever
before doing the accompanying changes and passing around old_whatever
to figure stuff out. Would make much more sense to me to the pass the
new value around and only update the port->whatever when things are
consistent. But let's try to work with what we have right now.
Quoting a follow-up from Ville:
"And naturally I forgot to amend the commit message w.r.t. this guy
[the change in drm_dp_destroy_port]. We don't really need to do this
here, but I figured I'd try to be a bit more consistent by having it,
just to avoid accidental mistakes if/when someone changes this stuff
again later."
v2: Clear port->pdt in the caller, if needed (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Carlos Santa <carlos.santa@intel.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Tested-by: Carlos Santa <carlos.santa@intel.com> Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97666 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1477488633-16544-1-git-send-email-ville.syrjala@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.
So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.
Signed-off-by: David Wu <david.wu@rock-chips.com> Tested-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvdimm_clear_poison cleared the user-visible badblocks, and sent
commands to the NVDIMM to clear the areas marked as 'poison', but it
neglected to clear the same areas from the internal poison_list which is
used to marshal ARS results before sorting them by namespace. As a
result, once on-demand ARS functionality was added:
37b137f nfit, libnvdimm: allow an ARS scrub to be triggered on demand
A scrub triggered from either sysfs or an MCE was found to be adding
stale entries that had been cleared from gendisk->badblocks, but were
still present in nvdimm_bus->poison_list. Additionally, the stale entries
could be triggered into producing stale disk->badblocks by simply disabling
and re-enabling the namespace or region.
This adds the missing step of clearing poison_list entries when clearing
poison, so that it is always in sync with badblocks.
Fixes: 37b137f ("nfit, libnvdimm: allow an ARS scrub to be triggered on demand") Signed-off-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI tegra host bridge driver adds the PCI IO resource retrieved from
firmware to the host bridge resource windows even if the
pci_remap_iospace() call fails; this is an actual bug in that the PCI host
bridge would consider the PCI IO resource valid (and possibly assign it to
downstream devices) even if the kernel was not able to map the PCI host
bridge memory address driving IO cycle to the CPU virtual address space (ie
pci_remap_iospace() failures).
Add the PCI host bridge driver pci_remap_iospace() failure path and do not
add the corresponding PCI host bridge PCI IO resources retrieved through
firmware when the pci_remap_iospace() function call fails, fixing the
issue.
Fixes: e6e9f471f5fe ("PCI: tegra: Use generic pci_remap_iospace() rather than ARM32-specific one") Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI designware host bridge driver does not remove the PCI IO resource
from the host bridge resource windows if the pci_remap_iospace() call
fails; this is an actual bug in that the PCI host bridge would consider the
PCI IO resource valid (and possibly assign it to downstream devices) even
if the kernel was not able to map the PCI host bridge memory address
driving IO cycle to the CPU virtual address space (ie pci_remap_iospace()
failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: cbce7900598c ("PCI: designware: Make driver arch-agnostic") Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Jingoo Han <jingoohan1@gmail.com> CC: Pratyush Anand <pratyush.anand@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI versatile host bridge driver does not remove the PCI IO resource
from the host bridge resource windows if the pci_remap_iospace() call
fails; this is an actual bug in that the PCI host bridge would consider the
PCI IO resource valid (and possibly assign it to downstream devices) even
if the kernel was not able to map the PCI host bridge memory address
driving IO cycle to the CPU virtual address space (ie pci_remap_iospace()
failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: b7e78170efd4 ("PCI: versatile: Add DT-based ARM Versatile PB PCIe host driver") Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI common host bridge driver does not remove the PCI IO resource from
the host bridge resource windows if the pci_remap_iospace() call fails;
this is an actual bug in that the PCI host bridge would consider the PCI IO
resource valid (and possibly assign it to downstream devices) even if the
kernel was not able to map the PCI host bridge memory address driving IO
cycle to the CPU virtual address space (ie pci_remap_iospace() failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: 4e64dbe226e7 ("PCI: generic: Expose pci_host_common_probe() for use by other drivers") Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridge's memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI aardvark host bridge driver does not remove the PCI IO resource
from the host bridge resource windows if the pci_remap_iospace() call
fails; this is an actual bug in that the PCI host bridge would consider the
PCI IO resource valid (and possibly assign it to downstream devices) even
if the kernel was not able to map the PCI host bridge memory address
driving IO cycle to the CPU virtual address space (ie pci_remap_iospace()
failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI rcar host bridge driver does not remove the PCI IO resource from
the host bridge resource windows if the pci_remap_iospace() call fails;
this is an actual bug in that the PCI host bridge would consider the PCI IO
resource valid (and possibly assign it to downstream devices) even if the
kernel was not able to map the PCI host bridge memory address driving IO
cycle to the CPU virtual address space (ie pci_remap_iospace() failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: 5d2917d469fa ("PCI: rcar: Convert to DT resource parsing API") Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Phil Edworthy <phil.edworthy@renesas.com> CC: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b8d368caa8dc ("ARM: dts: omap3: overo: remove unneded unit names
in display nodes") removed the unit names for all Overo display nodes
that didn't have a reg property.
But the display in arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi does
have a reg property so the correct fix was to make the unit name match
the value of the reg property, instead of removing it.
This patch fixes the following DTC warning for boards using this dtsi:
"ocp/spi@48098000/display has a reg or ranges property, but no unit name"
Fixes: b8d368caa8dc ("ARM: dts: omap3: overo: remove unneded unit names in display nodes") Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ethernet version in the earlier RealView EB variants is
LAN91C111 and not LAN9118 according to ARM DUI 0303E
"RealView Emulation Baseboard User Guide" page 3-57.
Make sure that this is used for the base variant of the board.
As the DT bindings for LAN91C111 does not specify any power
supplies, these need to be deleted from the DTS file.
Fixes: 2440d29d2ae2 ("ARM: dts: realview: support all the RealView EB board variants") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 9bf448c66d4b ("ARM: pxa: use generic gpio operation instead of
gpio register") from Oct 17, 2011, leads to the following static checker
warning:
arch/arm/mach-pxa/spitz_pm.c:172 spitz_charger_wakeup()
warn: double left shift '!gpio_get_value(SPITZ_GPIO_KEY_INT)
<< (1 << ((SPITZ_GPIO_KEY_INT) & 31))'
As Dan reported, the value is shifted three times :
- once by gpio_get_value(), which returns either 0 or BIT(gpio)
- once by the shift operation '<<'
- a last time by GPIO_bit(gpio) which is BIT(gpio)
Therefore the calculation lead to a chained or operator of :
- (1 << gpio) << (1 << gpio) = (2^gpio)^gpio = 2 ^ (gpio * gpio)
It is be sheer luck the former statement works, only because each gpio
used is strictly smaller than 6, and therefore 2^(gpio^2) never
overflows a 32 bits value, and because it is used as a boolean value to
check a gpio activation.
As the xxx_charger_wakeup() functions are used as a true/false detection
mechanism, take that opportunity to change their prototypes from integer
return value to boolean one.
Fixes: 9bf448c66d4b ("ARM: pxa: use generic gpio operation instead of
gpio register") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Joe Perches <joe@perches.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since its initial commit, the driver is buggy for multiple interrupts
handling. The translation from the former lubbock.c file was not
complete, and might stall all interrupt handling when multiple
interrupts occur.
This is especially true when inside the interrupt handler and if a new
interrupt comes and is not handled, leaving the output line still held,
and not creating a transition as the GPIO block behind would expect to
trigger another cplds_irq_handler() call.
For the record, the hardware is working as follows.
The interrupt mechanism relies on :
- one status register
- one mask register
Let's suppose the input irq lines are called :
- i_sa1111
- i_lan91x
- i_mmc_cd
Let's suppose the status register for each irq line is called :
- status_sa1111
- status_lan91x
- status_mmc_cd
Let's suppose the interrupt mask for each irq line is called :
- irqen_sa1111
- irqen_lan91x
- irqen_mmc_cd
Let's suppose the output irq line, connected to GPIO0 is called :
- o_gpio0
The behavior is as follows :
- o_gpio0 = not((status_sa1111 & irqen_sa1111) |
(status_lan91x & irqen_lan91x) |
(status_mmc_cd & irqen_mmc_cd))
=> this is a N-to-1 NOR gate and multiple AND gates
- irqen_* is exactly as programmed by a write to the FPGA
- status_* behavior is governed by a bi-stable D flip-flop
=> on next FPGA clock :
- if i_xxx is high, status_xxx becomes 1
- if i_xxx is low, status_xxx remains as it is
- if software sets status_xxx to 0, the D flip-flop is reset
=> status_xxx becomes 0
=> on next FPGA clock cycle, if i_xxx is high, status_xxx becomes
1 again
Fixes: fc9e38c0f4d3 ("ARM: pxa: lubbock: use new pxa_cplds driver") Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some CPUs like the 8xx, _PAGE_RW hence _PAGE_WRITE is defined
as 0 and _PAGE_RO has to be set when a page is not writable
_PAGE_RO is defined by default in pte-common.h, however BOOK3S/64
doesn't include that file so _PAGE_RO has to be defined explicitly
in book3s/64/pgtable.h
When we merge two contiguous partitions whose signatures are marked
NVRAM_SIG_FREE, We need update prev's length and checksum, then write it
to nvram, not cur's. So lets fix this mistake now.
Also use memset instead of strncpy to set the partition's name. It's
more readable if we want to fill up with duplicate chars .
Fixes: fa2b4e54d41f ("powerpc/nvram: Improve partition removal") Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
giveup_all() causes FPU/VMX/VSX facilities to be disabled in a threads
MSR. If the thread performing the giveup was transactional, the kernel
must record which facilities were in use before the giveup as the
thread must have these facilities re-enabled on return to userspace.
>From process.c:
/*
* This is called if we are on the way out to userspace and the
* TIF_RESTORE_TM flag is set. It checks if we need to reload
* FP and/or vector state and does so if necessary.
* If userspace is inside a transaction (whether active or
* suspended) and FP/VMX/VSX instructions have ever been enabled
* inside that transaction, then we have to keep them enabled
* and keep the FP/VMX/VSX state loaded while ever the transaction
* continues. The reason is that if we didn't, and subsequently
* got a FP/VMX/VSX unavailable interrupt inside a transaction,
* we don't know whether it's the same transaction, and thus we
* don't know which of the checkpointed state and the transactional
* state to use.
*/
Calling check_if_tm_restore_required() will set TIF_RESTORE_TM and
save the MSR if needed.
Comment from arch/powerpc/kernel/process.c:967:
If userspace is inside a transaction (whether active or
suspended) and FP/VMX/VSX instructions have ever been enabled
inside that transaction, then we have to keep them enabled
and keep the FP/VMX/VSX state loaded while ever the transaction
continues. The reason is that if we didn't, and subsequently
got a FP/VMX/VSX unavailable interrupt inside a transaction,
we don't know whether it's the same transaction, and thus we
don't know which of the checkpointed state and the ransactional
state to use.
restore_math() restore_fp() and restore_altivec() currently may not
restore the registers. It doesn't appear that this is more serious
than a performance penalty. If the math registers aren't restored the
userspace thread will still be run with the facility disabled.
Userspace will not be able to read invalid values. On the first access
it will take an facility unavailable exception and the kernel will
detected an active transaction, at which point it will abort the
transaction. There is the possibility for a pathological case
preventing any progress by transactions, however, transactions
are never guaranteed to make progress.
Fixes: 70fe3d9 ("powerpc: Restore FPU/VEC/VSX if previously used") Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In _scsih_io_done() we test if the ioc->logging_level does _not_ have
the MPT_DEBUG_REPLY bit set and if it hasn't we print the debug
messages. This unfortunately is the wrong way around.
Note, the actual bug is older than af0094115 but this commit removed the
CONFIG_SCSI_MPT3SAS_LOGGING Kconfig option which hid the bug.
Fixes: af0094115 'mpt2sas, mpt3sas: Remove SCSI_MPTXSAS_LOGGING entry from Kconfig' Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: Chaitra P B <chaitra.basappa@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were assigning the return value of iwl_mvm_ctdp_command() to a
variable, but never checking it. If this command fails, we should not
allow the interface up process to proceed, since it is potentially
dangerous to ignore thermal management requirements.
On default queue we will not receive frame release notification,
but the BAR itself.
Upon receiving the BAR driver should look at the NSSN and adjust
window accordingly.
Since the SCD_QUEUE_CFG command was introduced the driver
calls iwl_trans_txq_enable_cfg() with a NULL for scd_cfg
parameter.
This makes the transport avoid writing to the SCD pointers,
since it can cause races with firmware, which is also accessing
the registers.
The transport only updates the write pointer in that case.
Fix a wrong call to iwl_trans_txq_enable() which caused a
scd_cfg parameter to be sent to transport, resulting with an
access to SCD registers.
In iwl_mvm_rx_tx_cmd_single(), when checking if a given TID is
aggregated, the driver doesn't check whether or not the queue
itself can be aggregated. For example, a management queue might
be marked as aggregated if TID 0 is aggregated on a (different)
data queue.
Make sure that mgmt frames are sent with TID IWL_TID_NON_QOS,
and in this way make sure no mixups of this sort happen.
In 9000 family products we added an option to let the OEM fuse the
mac address via registers. If these registers are zeroed we use the OTP
address instead. Make sure that the address provided by the OEM is valid
and, if not, fall back to the OTP address as well.
Fixes: commit 17c867bfe89b ("iwlwifi: add support for getting HW address from CSR") Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we call symbol__fixup_duplicate() we use algorithms to pick the
"best" symbols for cases where there are various functions/aliases to an
address, and those check zero size symbols, which, before calling
symbol__fixup_end() are _all_ symbols in a just parsed kallsyms file.
So first fixup the end, then fixup the duplicates.
Found while trying to figure out why 'perf test vmlinux' failed, see the
output of 'perf test -v vmlinux' to see cases where the symbols picked
as best for vmlinux don't match the ones picked for kallsyms.
Cc: Anton Blanchard <anton@samba.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 694bf407b061 ("perf symbols: Add some heuristics for choosing the best duplicate symbol") Link: http://lkml.kernel.org/n/tip-rxqvdgr0mqjdxee0kf8i2ufn@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can allow aliases to be kept, but we were checking this just when
loading vmlinux files, be consistent, do it for any symbol table loading
code that calls symbol__fixup_duplicate() by making this function check
.allow_aliases instead.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 680d926a8cb0 ("perf symbols: Allow symbol alias when loading map for symbol name") Link: http://lkml.kernel.org/n/tip-z0avp0s6cfjckc4xj3pdfjdz@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the --hierarchy option is used, each entry has its own hpp_list to
show the result. But it is not updating the width of each column for
perf-top. The perf-report command has no problem since it resets it
during header display.
'make -C tools/perf build-test' is failing with below log for poewrpc.
In file included from /tmp/tmp.3eEwmGlYaF/perf-4.8.0-rc4/tools/perf/perf.h:15:0,
from util/cpumap.h:8,
from util/env.c:1:
/tmp/tmp.3eEwmGlYaF/perf-4.8.0-rc4/tools/perf/perf-sys.h:23:56:
fatal error: ../../arch/powerpc/include/uapi/asm/unistd.h: No such file or directory
compilation terminated.
I bisected it and found it's failing from commit ad430729ae00 ("Remove:
kernel unistd*h files from perf's MANIFEST, not used").
Header file '../../arch/powerpc/include/uapi/asm/unistd.h' is included
only for powerpc in tools/perf/perf-sys.h.
By looking closly at commit history, I found little weird thing:
Commit f2d9cae9ea9e ("perf powerpc: Use uapi/unistd.h to fix build
error") replaced 'asm/unistd.h' with 'uapi/asm/unistd.h'
Commit d2709c7ce4c5 ("perf: Make perf build for x86 with UAPI
disintegration applied") removes all arch specific 'uapi/asm/unistd.h'
for all archs and adds generic <asm/unistd.h>.
Commit f0b9abfb0446 ("Merge branch 'linus' into perf/core") again
includes 'uapi/asm/unistd.h' for powerpc. Don't know how exactly this
happened as this change is not part of commit also.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1472630591-5089-1-git-send-email-ravi.bangoria@linux.vnet.ibm.com Fixes: ad430729ae00 ("Remove: kernel unistd*h files from perf's MANIFEST, not used") Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Milian reported that the event group on TUI shows duplicated overhead.
This was due to a bug on calculating hpp->buf position. The
hpp_advance() was called from __hpp__slsmg_color_printf() on TUI but
it's already called from the hpp__call_print_fn macro in __hpp__fmt().
The end result is that the print function returns number of bytes it
printed but the buffer advanced twice of the length.
This is generally not a problem since it doesn't need to access the
buffer again. But with event group, overhead needs to be printed
multiple times and hist_entry__snprintf_alignment() tries to fill the
space with buffer after it printed. So it (brokenly) showed the last
overhead again.
The bug was there from the beginning, but I think it's only revealed
when the alignment function was added.
Reported-by: Milian Wolff <milian.wolff@kdab.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Fixes: 89fee7094323 ("perf hists: Do column alignment on the format iterator") Link: http://lkml.kernel.org/r/20160912061958.16656-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM32 building it report following error when we build with
libbabeltrace:
util/data-convert-bt.c: In function 'add_bpf_output_values':
util/data-convert-bt.c:440:3: error: format '%lu' expects argument of type 'long unsigned int', but argument 5 has type 'unsigned int' [-Werror=format]
cc1: all warnings being treated as errors
Fix it by changing %lu to %zu.
Signed-off-by: Wang Nan <wangnan0@huawei.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Zefan Li <lizefan@huawei.com> Cc: pi3orama@163.com Fixes: 6122d57e9f7c ("perf data: Support converting data from bpf_perf_event_output()") Link: http://lkml.kernel.org/r/1475035126-146587-1-git-send-email-wangnan0@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk-divider uses clk_readl()/clk_writel() everywhere, except in
clk_divider_round_rate(), where plain readl() is used. Change this to
clk_readl(), as it makes a difference on powerpc.
Fixes: e6d5e7d90be92cee ("clk-divider: Fix READ_ONLY when divider > 1") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts commit 023bd7166be0 ("clk: skip unnecessary
set_phase if nothing to do"), fixing two problems:
* in some SoCs, the hardware phase delay depends on the rate ratio of
the clock and its parent. So, changing this ratio may imply to set
new hardware values, even if the logical delay is the same.
* when the delay was the same as previously, an error was returned.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Fixes: 023bd7166be0 ("clk: skip unnecessary set_phase if nothing to do") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 0861e5b8cf80 (clk: Add clk_hw OF clk providers,
2016-02-05) __of_clk_get_from_provider() would return an error
pointer of the provider's choosing if there was a provider
registered and EPROBE_DEFER otherwise. After that commit, it
would return EPROBE_DEFER regardless of whether or not the
provider returned an error. This is odd and can lead to behavior
where clk consumers keep probe deferring when they should be
seeing some other error.
Let's restore the previous behavior where we only return
EPROBE_DEFER when there isn't a provider in our of_clk_providers
list. Otherwise, return the error from the last provider we find
that matches the node.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com> Fixes: 0861e5b8cf80 ("clk: Add clk_hw OF clk providers") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the firmware had set up a clock to source from PLLC, go along with
it. But if we're looking for a new parent, we don't want to switch it
to PLLC because the firmware will force PLLC (and thus the AXI bus
clock) to different frequencies during over-temp/under-voltage,
without notification to Linux.
On my system, this moves the Linux-enabled HDMI state machine and DSI1
escape clock over to plld_per from pllc_per. EMMC still ends up on
pllc_per, because the firmware had set it up to use that.
Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks") Acked-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
con3270 contains an optimisation that reduces the amount of data to be
transmitted to the 3270 terminal by putting a Repeat to Address (RA)
order into the data stream. The RA order itself takes up space, so
con3270 only uses it if there's enough space left in the line
buffer. Otherwise it just pads out the line manually.
For lines that were _just_ short enough that the RA order still fit in
the line buffer, the line was instead padded with an insufficient
amount of spaces. This was caused by examining the size of the
allocated line buffer rather than the length of the string to be
displayed.
For con3270_cline_end(), we just compare against the line length. For
con3270_update_string() however that isn't available anymore, so we
check whether the Repeat to Address order is present.
Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Tested-by: Jing Liu <liujbjl@linux.vnet.ibm.com> Tested-by: Yang Chen <bjcyang@linux.vnet.ibm.com> Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
con3270 contains an optimisation that reduces the amount of data to be
transmitted to the 3270 terminal by putting a Repeat to Address (RA)
order into the data stream. The RA order itself takes up space, so
con3270 only uses it if there's enough space left in the line
buffer. Otherwise it just pads out the line manually.
For lines too long to include the RA order, one byte was left
uninitialised. This was caused by an off-by-one bug in the loop that
pads out the line. Since the buffer is allocated from a common pool,
the single byte left uninitialised contained some previous buffer
content. Usually this was just a space or some character (which can
result in clutter but is otherwise harmless). Sometimes, however, it
was a Repeat to Address order, messing up the entire screen layout and
causing the display to send the entire buffer content on every
keystroke.
Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Reported-by: Liu Jing <liujbjl@linux.vnet.ibm.com> Tested-by: Jing Liu <liujbjl@linux.vnet.ibm.com> Tested-by: Yang Chen <bjcyang@linux.vnet.ibm.com> Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 9f3d6d7 chsc_get_channel_measurement_chars is called with
interrupts disabled during resume from hibernate. Since this function
used spin_unlock_irq, interrupts have been enabled accidentally. Fix
this by using the irqsave variant.
Since we can't guarantee the IRQ-enablement state for all (future/
external) callers, change the locking in related functions to prevent
similar bugs in the future.
Fixes: 9f3d6d7 ("s390/cio: update measurement characteristics") Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a view destruction command was present in the command stream, the
view was validated to avoid a device error. That caused excessive and
unnecessary validations of views, surfaces and mobs on view destruction.
Replace this with a new relocation type that patches the view
destruction command to a NOP if the view is not present in the device
after the execbuf validation sequence.
Also add checks for the member size of the vmw_res_relocation struct.
Fixes sporadic command submission errors on google-earth exit.
Reported-by: Brian Paul <brianp@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For every pfn aligned to minimum_order, dissolve_free_huge_pages() will
call dissolve_free_huge_page() which takes the hugetlb spinlock, even if
the page is not huge at all or a hugepage that is in-use.
Improve this by doing the PageHuge() and page_count() checks already in
dissolve_free_huge_pages() before calling dissolve_free_huge_page(). In
dissolve_free_huge_page(), when holding the spinlock, those checks need
to be revalidated.
Link: http://lkml.kernel.org/r/20160926172811.94033-4-gerald.schaefer@de.ibm.com Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Rui Teng <rui.teng@linux.vnet.ibm.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dissolve_free_huge_pages(), free hugepages will be dissolved without
making sure that there are enough of them left to satisfy hugepage
reservations.
Fix this by adding a return value to dissolve_free_huge_pages() and
checking h->free_huge_pages vs. h->resv_huge_pages. Note that this may
lead to the situation where dissolve_free_huge_page() returns an error
and all free hugepages that were dissolved before that error are lost,
while the memory block still cannot be set offline.
Fixes: c8721bbb ("mm: memory-hotplug: enable memory hotplug to handle hugepage") Link: http://lkml.kernel.org/r/20160926172811.94033-3-gerald.schaefer@de.ibm.com Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Rui Teng <rui.teng@linux.vnet.ibm.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A workaround for a warning introduced a use of the NO_IRQ
macro that should have been gone for a long time.
It is clear from the code that the value cannot actually
be used, but apparently there was a configuration at
some point that caused a warning, so instead of just
reverting that patch, this rearranges the code in a way that
the warning cannot reappear.
bq->charger is initialized in bq24257_power_supply_init.
Therefore, bq24257_power_supply_init should be called before the
registration of the IRQ handler bq24257_irq_handler_thread that calls
power_supply_changed(bq->charger).
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Cc: Aurelien Chanot <chanot.a@gmail.com> Cc: Andreas Dannenberg <dannenberg@ti.com> Cc: Sebastian Reichel <sre@kernel.org> Cc: David Woodhouse <dwmw2@infradead.org> Fixes: 2219a935963e ("power_supply: Add TI BQ24257 charger driver") Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have a global qpt_mask as that does not support the
multiple chip model which qib has. Instead rely on the value which
exists already in the device data (dd).
Fixes: 898fa52b4ac3 "IB/qib: Remove qpn, qp tables and related variables from qib" Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_completion_interruptible_timeout return 0 on timeout and
-ERESTARTSYS if interrupted. The check for
!wait_for_completion_interruptible_timeout() would report an interrupt
as timeout. Further, while HZ/50 will work most of the time it could
fail for HZ < 50, so this is switched to msecs_to_jiffies(20).
Fixes: 13a9930d15b4 ("staging: ks7010: add driver from Nanonote extra-repository") Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fadbe0cd5292851608e2e01b91d9295fa287b9fe ("staging: rtl8188eu:
Remove rtw_zmalloc(), wrapper for kzalloc()") changed all allocation
calls to be GFP_KERNEL even though the original wrapper was testing
to determine if the caller was in atomic mode. Most of the mistakes
were corrected with commit 33dc85c3c667209c930b2dac5ccbc2a365e06b7a
("staging: r8188eu: Fix scheduling while atomic error introduced in
commit fadbe0cd"); however, two kzalloc calls were missed as the
call only happens when the driver is shutting down.
Commit 6fba39cf32a3 ("staging: sm750fb: use BIT macro for
PANEL_DISPLAY_CTRL single-bit fields") accidentally changed the
CLOCK_PHASE logic from '|=' to '=' which clears all the previously set
bits.
Fixes: 6fba39cf32a3 ("staging: sm750fb: use BIT macro for PANEL_DISPLAY_CTRL single-bit fields") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added Hi6220 Ion code fails to build when the ION_OF helpers
are not present:
drivers/staging/android/ion/hisilicon/hi6220_ion.o: In function `hi6220_ion_remove':
hi6220_ion.c:(.text.hi6220_ion_remove+0x4c): undefined reference to `ion_destroy_platform_data'
drivers/staging/android/ion/hisilicon/hi6220_ion.o: In function `hi6220_ion_probe':
hi6220_ion.c:(.text.hi6220_ion_probe+0x5c): undefined reference to `ion_parse_dt'
hi6220_ion.c:(.text.hi6220_ion_probe+0xf8): undefined reference to `ion_destroy_platform_data'
This selects the symbol when needed.
Fixes: 2b40182a19bc ("staging: android: ion: Add ion driver for Hi6220 SoC platform") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison for devnr limits is off-by-one, the current check
allows 0 to AD5755_NUM_CHANNELS and the limit should be in fact
0 to AD5755_NUM_CHANNELS - 1. This can lead to an out of bounds
write to pdata->dac[devnr]. Fix this by replacing > with >= on the
comparison.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Fixes: c947459979c6 ("iio: ad5755: add support for dt bindings") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d88429a695a4 ("ASoC: dapm: Add output driver widget") added
the snd_soc_dapm_out_drv ID for the output driver widget, which is
the same as the PGA widget, with a later power sequence number.
Commit 19a2557b76d6 ("ASoC: dapm: Add kcontrol support for PGAs")
then added kcontrol support for PGA widgets, but failed to account
for output driver widgets. Attempts to use kcontrols with output
driver widgets result in silent failures, with the developer having
little idea about what went on.
Add snd_soc_dapm_out_drv to the switch/case block under snd_soc_dapm_pga
in dapm_create_or_share_kcontrol, since they are essentially the same.
Fixes: 19a2557b76d6 (ASoC: dapm: Add kcontrol support for PGAs) Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value for the second channel in _ENUM_DOUBLE (double channel) MUXs
is not correctly updated, due to using the wrong bit shift.
Use the correct bit shift, so both channels toggle together.
Fixes: 3727b4968453 (ASoC: dapm: Consolidate MUXs and value MUXs) Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If soc_dapm_read() fails, val will be uninitialized, and bogus values
will be written later:
ret = soc_dapm_read(dapm, reg, &val);
val = (val >> shift) & mask;
However, the compiler does not give a warning. Return on error before
val is really used to avoid this.
This is similar to the commit 6912831623c5 ("ASoC: dapm: Fix
uninitialized variable in snd_soc_dapm_get_enum_double()")
Fixes: ce0fc93ae56e (ASoC: Add DAPM support at the component level) Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently omap-rng checks the return value of pm_runtime_get_sync and
reports failure if anything is returned, however it should be checking
if ret < 0 as pm_runtime_get_sync return 0 on success but also can return
1 if the device was already active which is not a failure case. Only
values < 0 are actual failures.
Fixes: 61dc0a446e5d ("hwrng: omap - Fix assumption that runtime_get_sync will always succeed") Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
