In cm_write(), 'buf' is allocated through kzalloc(). In the following
execution, if an error occurs, 'buf' is not deallocated, leading to memory
leaks. To fix this issue, free 'buf' before returning the error.
Fixes: 526b4af47f44 ("ACPI: Split out custom_method functionality into an own driver") Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply
for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit,
but it turned out that it supplies also some other critical parts and
board freezes/crashes when it is turned off.
The mentioned commit made Exynos TMU a consumer of that regulator and in
typical case Exynos TMU driver keeps it enabled from early boot. However
there are such configurations (example is multi_v7_defconfig), in which
some of the regulators are compiled as modules and are not available
from early boot. In such case it may happen that LDO10 is turned off by
regulator core, because it has no consumers yet (in this case consumer
drivers cannot get it, because the supply regulators for it are not yet
available). This in turn causes the board to crash. This patch restores
'always-on' property for the LDO10 regulator.
Fixes: aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
because the allocation could fail from iommu_map_page(), and the volume
of this call could be huge which may generate a lot of serial console
output and cosumes all CPUs.
Fix it by silencing the warning in this call site, and there is still a
dev_err() later to notify the failure.
In nvme spec 1.3 there is a definition for data write/read counters
from SMART log, (See section 5.14.1.2):
This value is reported in thousands (i.e., a value of 1
corresponds to 1000 units of 512 bytes read) and is rounded up.
However, in nvme target where value is reported with actual units,
but not thousands of units as the spec requires.
Signed-off-by: Tom Wu <tomwu@mellanox.com> Reviewed-by: Israel Rukshin <israelr@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the MMUs is disabled, I-cache speculation can result in
instructions being fetched from the PoC. During boot we may patch
instructions (e.g. for alternatives and jump labels), and these may be
dirty at the PoU (and stale at the PoC).
Thus, while the MMU is disabled in the KPTI pagetable fixup code we may
load stale instructions into the I-cache, potentially leading to
subsequent crashes when executing regions of code which have been
modified at runtime.
Similarly to commit:
8ec41987436d566f ("arm64: mm: ensure patched kernel text is fetched from PoU")
... we can invalidate the I-cache after enabling the MMU to prevent such
issues.
The KPTI pagetable fixup code itself should be clean to the PoC per the
boot protocol, so no maintenance is required for this code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the ACPI 6.3 specification, the _PSD method is optional
when using CPPC. The underlying assumption is that each CPU can change
frequency independently from all other CPUs; _PSD is provided to tell
the OS that some processors can NOT do that.
However, the acpi_get_psd() function returns ENODEV if there is no _PSD
method present, or an ACPI error status if an error occurs when evaluating
_PSD, if present. This makes _PSD mandatory when using CPPC, in violation
of the specification, and only on Linux.
This has forced some firmware writers to provide a dummy _PSD, even though
it is irrelevant, but only because Linux requires it; other OSPMs follow
the spec. We really do not want to have OS specific ACPI tables, though.
So, correct acpi_get_psd() so that it does not return an error if there
is no _PSD method present, but does return a failure when the method can
not be executed properly. This allows _PSD to be optional as it should
be.
Signed-off-by: Al Stone <ahs3@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour
Prevent mangling with gains with invalid values.
As pointed by Sylvester, this should never happen in practice,
as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16
and m is always >= 0), but it is too hard for a static analyzer
to get this, as the logic with validates control min/max is
elsewhere inside V4L2 core.
In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array().
However, it is not deallocated if the following allocation for urbs fails.
To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If saa7146_register_device() fails, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, perform necessary cleanup work
before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Regulators should be enabled before clocks to avoid h/w hang. This
require change in exynos_bus_probe() to move exynos_bus_parse_of()
after exynos_bus_parent_parse_of() and change in error handling.
Similar change is needed in exynos_bus_exit() where clock should be
disabled before regulators.
This happens because devres_release_all will first remove all the nodes
into a separate todo list so the nested devres_release from
devm_devfreq_unregister_notifier won't find anything.
Fix the warning by calling the non-devm APIS for frequency notification.
Using devm wrappers is not actually useful for a governor anyway: it
relies on the devfreq core to correctly match the GOV_START/GOV_STOP
notifications.
Fixes: 996133119f57 ("PM / devfreq: Add new passive governor") Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dvb_create_media_entity(), 'dvbdev->entity' is allocated through
kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if
kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading
to a memory leak bug. To fix this issue, free 'dvbdev->entity' before
returning -ENOMEM.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Recent changes to the atheros at803x driver caused
ethernet to stop working on this board.
In particular commit 6d4cd041f0af
("net: phy: at803x: disable delay only for RGMII mode")
and commit cd28d1d6e52e
("net: phy: at803x: Disable phy delay for RGMII mode")
fix the AR8031 driver to configure the phy's (RX/TX)
delays as per the 'phy-mode' in the device tree.
This now prevents ethernet from working on this board.
It used to work before those commits, because the
AR8031 comes out of reset with RX delay enabled, and
the at803x driver didn't touch the delay configuration
at all when "rgmii" mode was selected, and because
arch/arm/mach-imx/mach-imx7d.c:ar8031_phy_fixup()
unconditionally enables TX delay.
Since above commits ar8031_phy_fixup() also has no
effect anymore, and the end-result is that all delays
are disabled in the phy, no ethernet.
Update the device tree to restore functionality.
Signed-off-by: André Draszik <git@andred.net> CC: Ilya Ledvich <ilya@compulab.co.il> CC: Igor Grinberg <grinberg@compulab.co.il> CC: Rob Herring <robh+dt@kernel.org> CC: Mark Rutland <mark.rutland@arm.com> CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <s.hauer@pengutronix.de> CC: Pengutronix Kernel Team <kernel@pengutronix.de> CC: Fabio Estevam <festevam@gmail.com> CC: NXP Linux Team <linux-imx@nxp.com> CC: devicetree@vger.kernel.org CC: linux-arm-kernel@lists.infradead.org Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
compile-testing this driver on other architectures showed
multiple warnings:
drivers/net/ethernet/nxp/lpc_eth.c: In function 'lpc_eth_drv_probe':
drivers/net/ethernet/nxp/lpc_eth.c:1337:19: warning: format '%d' expects argument of type 'int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
drivers/net/ethernet/nxp/lpc_eth.c:1342:19: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
Use format strings that work on all architectures.
The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.
When compile-testing on other architectures, we get lots of warnings
about incorrect format strings, like:
drivers/dma/iop-adma.c: In function 'iop_adma_alloc_slots':
drivers/dma/iop-adma.c:307:6: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
drivers/dma/iop-adma.c: In function 'iop_adma_prep_dma_memcpy':
>> drivers/dma/iop-adma.c:518:40: warning: format '%u' expects argument of type 'unsigned int', but argument 5 has type 'size_t {aka long unsigned int}' [-Wformat=]
Use %zu for printing size_t as required, and cast the dma_addr_t
arguments to 'u64' for printing with %llx. Ideally this should use
the %pad format string, but that requires an lvalue argument that
doesn't work here.
AER info of PCIe fatal error is not printed in the current driver.
Because APEI driver will panic directly for fatal error, and can't
run to the place of printing AER info.
An example log is as following:
{763}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 11
{763}[Hardware Error]: event severity: fatal
{763}[Hardware Error]: Error 0, type: fatal
{763}[Hardware Error]: section_type: PCIe error
{763}[Hardware Error]: port_type: 0, PCIe end point
{763}[Hardware Error]: version: 4.0
{763}[Hardware Error]: command: 0x0000, status: 0x0010
{763}[Hardware Error]: device_id: 0000:82:00.0
{763}[Hardware Error]: slot: 0
{763}[Hardware Error]: secondary_bus: 0x00
{763}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10fb
{763}[Hardware Error]: class_code: 000002
Kernel panic - not syncing: Fatal hardware error!
This issue was imported by the patch, '37448adfc7ce ("aerdrv: Move
cper_print_aer() call out of interrupt context")'. To fix this issue,
this patch adds print of AER info in cper_print_pcie() for fatal error.
Here is the example log after this patch applied:
{24}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 10
{24}[Hardware Error]: event severity: fatal
{24}[Hardware Error]: Error 0, type: fatal
{24}[Hardware Error]: section_type: PCIe error
{24}[Hardware Error]: port_type: 0, PCIe end point
{24}[Hardware Error]: version: 4.0
{24}[Hardware Error]: command: 0x0546, status: 0x4010
{24}[Hardware Error]: device_id: 0000:01:00.0
{24}[Hardware Error]: slot: 0
{24}[Hardware Error]: secondary_bus: 0x00
{24}[Hardware Error]: vendor_id: 0x15b3, device_id: 0x1019
{24}[Hardware Error]: class_code: 000002
{24}[Hardware Error]: aer_uncor_status: 0x00040000, aer_uncor_mask: 0x00000000
{24}[Hardware Error]: aer_uncor_severity: 0x00062010
{24}[Hardware Error]: TLP Header: 000000c0010100000000000100000000
Kernel panic - not syncing: Fatal hardware error!
Fixes: 37448adfc7ce ("aerdrv: Move cper_print_aer() call out of interrupt context") Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Reviewed-by: James Morse <james.morse@arm.com>
[ardb: put parens around terms of && operator] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Then from kernel side, Manage_add invokes the path (add_new_disk ->
validate_super = super_1_validate) to set In_sync flag.
Since In_sync means "device is in_sync with rest of array", and the new
added disk need to resync thread to help the synchronization of data.
And md_reap_sync_thread would call spare_active to set In_sync for the
new added disk finally. So don't set In_sync if array is in frozen.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When add one disk to array, the md_reap_sync_thread is responsible
to activate the spare and set In_sync flag for the new member in
spare_active().
But if raid1 has one member disk A, and disk B is added to the array.
Then we offline A before all the datas are synchronized from A to B,
obviously B doesn't have the latest data as A, but B is still marked
with In_sync flag.
So let's not call spare_active under the condition, otherwise B is
still showed with 'U' state which is not correct.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Linux kernel assumes that get_endpoint(alts,0) and
get_endpoint(alts,1) are eachothers feedback endpoints.
To reassure that validity it will test bsynchaddress to comply with that
assumption. But if the bsyncaddress is 0 (invalid), it will flag that as
a wrong assumption and return an error.
Fix: Skip the test if bSynchAddress is 0.
Note: those with a valid bSynchAddress should have a code quirck added.
In build_adc_controls(), there is an if statement on line 773 to check
whether ak->adc_info is NULL:
if (! ak->adc_info ||
! ak->adc_info[mixer_ch].switch_name)
When ak->adc_info is NULL, it is used on line 792:
knew.name = ak->adc_info[mixer_ch].selector_name;
Thus, a possible null-pointer dereference may occur.
To fix this bug, referring to lines 773 and 774, ak->adc_info
and ak->adc_info[mixer_ch].selector_name are checked before being used.
This bug is found by a static analysis tool STCheck written by us.
The last fallback of CORB/RIRB communication error recovery is to turn
on the single command mode, and this last resort usually means that
something is really screwed up. Instead of a normal dev_err(), show
the error more clearly with dev_WARN() with the caller stack trace.
Also, show the bus-reset fallback also as an error, too.
A reboot request sends an IPI via the reboot vector and waits for all other
CPUs to stop. If one or more CPUs are in critical regions with interrupts
disabled then the IPI is not handled on those CPUs and the shutdown hangs
if native_stop_other_cpus() is called with the wait argument set.
Such a situation can happen when one CPU was stopped within a lock held
section and another CPU is trying to acquire that lock with interrupts
disabled. There are other scenarios which can cause such a lockup as well.
In theory the shutdown should be attempted by an NMI IPI after the timeout
period elapsed. Though the wait loop after sending the reboot vector IPI
prevents this. It checks the wait request argument and the timeout. If wait
is set, which is true for sys_reboot() then it won't fall through to the
NMI shutdown method after the timeout period has finished.
This was an oversight when the NMI shutdown mechanism was added to handle
the 'reboot IPI is not working' situation. The mechanism was added to deal
with stuck panic shutdowns, which do not have the wait request set, so the
'wait request' case was probably not considered.
Remove the wait check from the post reboot vector IPI wait loop and enforce
that the wait loop in the NMI fallback path is invoked even if NMI IPIs are
disabled or the registration of the NMI handler fails. That second wait
loop will then hang if not all CPUs shutdown and the wait argument is set.
[ tglx: Avoid the hard to parse line break in the NMI fallback path,
add comments and massage the changelog ]
Fixes: 7d007d21e539 ("x86/reboot: Use NMI to assist in shutting down if IRQ fails") Signed-off-by: Grzegorz Halat <ghalat@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Don Zickus <dzickus@redhat.com> Link: https://lkml.kernel.org/r/20190628122813.15500-1-ghalat@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
On !CONFIG_RT_GROUP_SCHED configurations it is currently not possible to
move RT tasks between cgroups to which CPU controller has been attached;
but it is oddly possible to first move tasks around and then make them
RT (setschedule to FIFO/RR).
Also, as Michal noted, it is currently not possible to enable CPU
controller on unified hierarchy with !CONFIG_RT_GROUP_SCHED (if there
are any kernel RT threads in root cgroup, they can't be migrated to the
newly created CPU controller's root in cgroup_update_dfl_csses()).
Existing code comes with a comment saying the "we don't support RT-tasks
being in separate groups". Such comment is however stale and belongs to
pre-RT_GROUP_SCHED times. Also, it doesn't make much sense for
!RT_GROUP_ SCHED configurations, since checks related to RT bandwidth
are not performed at all in these cases.
Make moving RT tasks between CPU controller groups viable by removing
special case check for RT (and DEADLINE) tasks.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Michal Koutný <mkoutny@suse.com> Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: lizefan@huawei.com Cc: longman@redhat.com Cc: luca.abeni@santannapisa.it Cc: rostedt@goodmis.org Link: https://lkml.kernel.org/r/20190719063455.27328-1-juri.lelli@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The load_balance() has a dedicated mecanism to detect when an imbalance
is due to CPU affinity and must be handled at parent level. In this case,
the imbalance field of the parent's sched_group is set.
The description of sg_imbalanced() gives a typical example of two groups
of 4 CPUs each and 4 tasks each with a cpumask covering 1 CPU of the first
group and 3 CPUs of the second group. Something like:
{ 0 1 2 3 } { 4 5 6 7 }
* * * *
But the load_balance fails to fix this UC on my octo cores system
made of 2 clusters of quad cores.
Whereas the load_balance is able to detect that the imbalanced is due to
CPU affinity, it fails to fix it because the imbalance field is cleared
before letting parent level a chance to run. In fact, when the imbalance is
detected, the load_balance reruns without the CPU with pinned tasks. But
there is no other running tasks in the situation described above and
everything looks balanced this time so the imbalance field is immediately
cleared.
The imbalance field should not be cleared if there is no other task to move
when the imbalance is detected.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/1561996022-28829-1-git-send-email-vincent.guittot@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to increment the device count atomically before we checkout a
device to make sure that we do not reach the max count, otherwise we get
out-of-bounds errors as reported by syzbot.
Reported-and-tested-by: syzbot+aac8d0d7205f112045d2@syzkaller.appspotmail.com Signed-off-by: Luke Nowakowski-Krijger <lnowakow@eng.ucsd.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/exynos4-is/fimc-is.c:813:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:870:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:885:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:545:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 541, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:528:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:534:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_DVB_DIB9000 is disabled, we can still compile code that
now fails to link against dibx000_i2c_set_speed:
drivers/media/usb/dvb-usb/dib0700_devices.o: In function `dib01x0_pmu_update.constprop.7':
dib0700_devices.c:(.text.unlikely+0x1c9c): undefined reference to `dibx000_i2c_set_speed'
The call sites are both through dib01x0_pmu_update(), which gets passed
an 'i2c' pointer from dib9000_get_i2c_master(), which has returned
NULL. Checking this pointer seems to be a good idea anyway, and it avoids
the link failure in most cases.
Sean Young found another case that is not fixed by that, where certain
gcc versions leave an unused function in place that causes the link error,
but adding an explict IS_ENABLED() check also solves this.
Fixes: b7f54910ce01 ("V4L/DVB (4647): Added module for DiB0700 based devices") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Firmware files are in ASCII, using 2 hex characters per byte. The
maximum length of a firmware string is therefore
16 (commands) * 2 (bytes per command) * 2 (characters per byte) = 64
Fixes: ff45262a85db ("leds: add new LP5562 LED driver") Signed-off-by: Nick Stoughton <nstoughton@logitech.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V
The LM3632_LDO_VSEL_MAX should be 0b101000 (0x28), so the maximum voltage
can match the datasheet.
which has the hallmarks of a worker queued from interrupt after it was
supposedly cancelled (note the POISON_FREE), and I could not see where
the interrupt would be flushed on shutdown so added the likely suspects.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111174 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When creating a raw AF_NFC socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a raw AF_IEEE802154 socket, CAP_NET_RAW needs to be
checked first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a raw AF_AX25 socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a raw AF_APPLETALK socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a raw AF_ISDN socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a reset packet sizes and device mtu can change and need
to be reevaluated to calculate queue sizes.
Malicious devices can set this to zero and we divide by it.
Introduce sanity checking.
Reported-and-tested-by: syzbot+6102c120be558c885f04@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the drivers more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of these endpoints are used for memory allocations
and as divisors in many usbnet minidrivers. Avoiding zero is therefore
critical.
Running old skge driver on PowerPC causes checksum errors
because hardware reported 1's complement checksum is in little-endian
byte order.
Reported-by: Benoit <benoit.sansoni@gmail.com> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
userspace openvswitch patch "(dpif-linux: Implement the API
functions to allow multiple handler threads read upcall)"
changes its type from U32 to UNSPEC, but leave the kernel
unchanged
and after kernel 6e237d099fac "(netlink: Relax attr validation
for fixed length types)", this bug is exposed by the below
warning
[ 57.215841] netlink: 'ovs-vswitchd': attribute type 5 has an invalid length.
Fixes: 5cd667b0a456 ("openvswitch: Allow each vport to have an array of 'port_id's") Signed-off-by: Li RongQing <lirongqing@baidu.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the endpoint is unregistered there might still be work pending to
handle incoming messages, which will result in a use after free
scenario. The plan is to remove the rx_worker, but until then (and for
stable@) ensure that the work is stopped before the node is freed.
According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf129856 ("phy: Add file missed in previous commit.") Signed-off-by: Peter Mamonov <pmamonov@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue was caused by skb's true_size changed without its sk's
sk_wmem_alloc increased in tcp/skb_gro_receive(). Later when the
skb is being freed and the skb's truesize is subtracted from its
sk's sk_wmem_alloc in tcp_wfree(), underflow occurs.
macsec is calling gro_cells_receive() to receive a packet, which
actually requires skb->sk to be NULL. However when macsec dev is
over veth, it's possible the skb->sk is still set if the skb was
not unshared or expanded from the peer veth.
ip_rcv() is calling skb_orphan() to drop the skb's sk for tproxy,
but it is too late for macsec's calling gro_cells_receive(). So
fix it by dropping the skb's sk earlier on rx path of macsec.
Fixes: 5491e7c6b1a9 ("macsec: enable GRO and RPS on macsec devices") Reported-by: Xiumei Mu <xmu@redhat.com> Reported-by: Fei Liu <feliu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the driver more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of the out pipe is used as divisor. So this change
fixes a divide-by-zero bug.
struct archdr is only big enough to hold the header of various types of
arcnet packets. So to provide enough space to hold the data read from
hardware provide a buffer large enough to hold a packet with maximal
size.
The problem was noticed by the stack protector which makes the kernel
oops.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "obvious" cause is that the attr ifork is null despite the inode
claiming an attr fork having at least one extent, but it's not so
obvious why we ended up with an inode in that state.
Reported-by: Zorro Lang <zlang@redhat.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204031 Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Bill O'Donnell <billodo@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to mark the output polling as disabled to prevent concurrent
irqs from queuing new work as shutdown the probe -- causing that work to
execute after we have freed the structs:
The testcase fails because that, in fuzzed image, current segment was
allocated with LFS type, its .next_blkoff should point to an unused
block address, but actually, its bitmap shows it's not. So during
allocation, f2fs crash when setting bitmap.
Introducing sanity_check_curseg() to check such inconsistence of
current in-used segment.
"We normally use -EUCLEAN to signal filesystem corruption. Plus, it is
good idea to report it to the syslog and mark filesystem as "needing
fsck" if filesystem can do that."
Still we need improve the original patch with:
- use unlikely keyword
- add message print
- return EUCLEAN
However, after rethink this patch, I don't think we should add such
condition check here as below reasons:
- We have already checked the field in f2fs_sanity_check_ckpt(),
- If there is fs corrupt or security vulnerability, there is nothing
to guarantee the field is integrated after the check, unless we do
the check before each of its use, however no filesystem does that.
- We only have similar check for bitmap, which was added due to there
is bitmap corruption happened on f2fs' runtime in product.
- There are so many key fields in SB/CP/NAT did have such check
after f2fs_sanity_check_{sb,cp,..}.
As a part of the sanity checking while mounting, distinct segment number
assignment to data and node segments is verified. Fixing a small bug in
this verification between node and data segments. We need to check all
the data segments with all the node segments.
Fixes: 042be0f849e5f ("f2fs: fix to do sanity check with current segment number") Signed-off-by: Surbhi Palande <csurbhi@gmail.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When allocating a range of LPIs for a Multi-MSI capable device,
this allocation extended to the closest power of 2.
But on the release path, the interrupts are released one by
one. This results in not releasing the "extra" range, leaking
the its_device. Trying to reprobe the device will then fail.
Fix it by releasing the LPIs the same way we allocate them.
Fixes: 8208d1708b88 ("irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size") Reported-by: Jiaxing Luo <luojiaxing@huawei.com> Tested-by: John Garry <john.garry@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/f5e948aa-e32f-3f74-ae30-31fee06c2a74@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Tetsuo Handa had reported he saw an incorrect "downgrading a read lock"
warning right after a previous lockdep warning. It is likely that the
previous warning turned off lock debugging causing the lockdep to have
inconsistency states leading to the lock downgrade warning.
Fix that by add a check for debug_locks at the beginning of
__lock_downgrade().
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Reported-by: syzbot+53383ae265fb161ef488@syzkaller.appspotmail.com Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: https://lkml.kernel.org/r/1547093005-26085-1-git-send-email-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This adds rate limiting to the message that is printed when reading a
power supply property via sysfs returns an error. This will prevent
userspace applications from unintentionally dDOSing the system by
continuously reading a property that returns an error.
Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receiving a deauthentication/disassociation frame from a TDLS
peer, a station should not disconnect the current AP, but only
disable the current TDLS link if it's enabled.
Without this change, a TDLS issue can be reproduced by following the
steps as below:
1. STA-1 and STA-2 are connected to AP, bidirection traffic is running
between STA-1 and STA-2.
2. Set up TDLS link between STA-1 and STA-2, stay for a while, then
teardown TDLS link.
3. Repeat step #2 and monitor the connection between STA and AP.
During the test, one STA may send a deauthentication/disassociation
frame to another, after TDLS teardown, with reason code 6/7, which
means: Class 2/3 frame received from nonassociated STA.
On receive this frame, the receiver STA will disconnect the current
AP and then reconnect. It's not a expected behavior, purpose of this
frame should be disabling the TDLS link, not the link with AP.
Cc: stable@vger.kernel.org Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function only consists of a single switch case block without a
default case. Unsupported control requests are indicated by the -EINVAL
return code trough the last return statement at the end of the function. So
exiting just the switch case block returns the -EINVAL error code but the
hue control is supported and a zero should be returned instead.
Replace the break by a 'return 0' to fix this behaviour.
Fixes: d183e4efcae8 ("[media] v4l: tvp5150: Add missing break in set
control handler")
As reported by the OpenWRT team, write requests sometimes fail on some
platforms.
Currently to check the state chip_ready() is used correctly as described by
the flash memory S29GL256P11TFI01 datasheet.
Also chip_good() is used to check if the write is succeeded and it was
implemented by the commit fb4a90bfcd6d8 ("[MTD] CFI-0002 - Improve error
checking").
But actually the write failure is caused on some platforms and also it can
be fixed by using chip_good() to check the state and retry instead.
Also it seems that it is caused after repeated about 1,000 times to retry
the write one word with the reset command.
By using chip_good() to check the state to be done it can be reduced the
retry with reset.
It is depended on the actual flash chip behavior so the root cause is
unknown.
The syzbot fuzzer has reported a pair of problems in the
hidraw_ioctl() function: slab-out-of-bounds read and use-after-free
read. An example of the first:
BUG: KASAN: slab-out-of-bounds in strlen+0x79/0x90 lib/string.c:525
Read of size 1 at addr ffff8881c8035f38 by task syz-executor.4/2833
It turns out the fault was caused by a bug in the HID Logitech driver,
which violates the requirement that every pathway calling
hid_hw_start() must also call hid_hw_stop(). This patch fixes the bug
by making sure the requirement is met.
The syzbot fuzzer provoked a general protection fault in the
hid-prodikeys driver:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc5+ #28
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:pcmidi_submit_output_report drivers/hid/hid-prodikeys.c:300 [inline]
RIP: 0010:pcmidi_set_operational drivers/hid/hid-prodikeys.c:558 [inline]
RIP: 0010:pcmidi_snd_initialise drivers/hid/hid-prodikeys.c:686 [inline]
RIP: 0010:pk_probe+0xb51/0xfd0 drivers/hid/hid-prodikeys.c:836
Code: 0f 85 50 04 00 00 48 8b 04 24 4c 89 7d 10 48 8b 58 08 e8 b2 53 e4 fc
48 8b 54 24 20 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f
85 13 04 00 00 48 ba 00 00 00 00 00 fc ff df 49 8b
The problem is caused by the fact that pcmidi_get_output_report() will
return an error if the HID device doesn't provide the right sort of
output report, but pcmidi_set_operational() doesn't bother to check
the return code and assumes the function call always succeeds.
This patch adds the missing check and aborts the probe operation if
necessary.
The upstream kernel commit cited below modified the workqueue in the
new CQ API to be bound to a specific CPU (instead of being unbound).
This caused ALL users of the new CQ API to use the same bound WQ.
Specifically, MAD handling was severely delayed when the CPU bound
to the WQ was busy handling (higher priority) interrupts.
This caused a delay in the MAD "heartbeat" response handling,
which resulted in ports being incorrectly classified as "down".
To fix this, add a new "unbound" WQ type to the new CQ API, so that users
have the option to choose either a bound WQ or an unbound WQ.
For MADs, choose the new "unbound" WQ.
Fixes: b7363e67b23e ("IB/device: Convert ib-comp-wq to be CPU-bound") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.m> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are devices which require low connection intervals for usable operation
including keyboards and mice. Forcing a static connection interval for
these types of devices has an impact in latency and causes a regression.
This is a custom patch (no mainline equivalent) for stable backport only
to address 0-Day kernel test infra ARC 4.x.y builds errors.
The reason for this custom patch as that it is a single patch, touches
only ARC, vs. atleast two 7c2c11b208be09c1, dc8635b78cd8669 which touch
atleast 3 other arches (one long removed) and could potentially have a
fallout.
After the conversion to lock-less dma-api call the
increase_address_space() function can be called without any
locking. Multiple CPUs could potentially race for increasing
the address space, leading to invalid domain->mode settings
and invalid page-tables. This has been happening in the wild
under high IO load and memory pressure.
Fix the race by locking this operation. The function is
called infrequently so that this does not introduce
a performance regression in the dma-api path again.
Reported-by: Qian Cai <cai@lca.pw> Fixes: 256e4621c21a ('iommu/amd: Make use of the generic IOVA allocator') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a request_key authentication token key gets revoked, there's a window in
which request_key_auth_describe() can see it with a NULL payload - but it
makes no check for this and something like the following oops may occur:
Identical to __put_user(); the __get_user() argument evalution will too
leak UBSAN crud into the __uaccess_begin() / __uaccess_end() region.
While uncommon this was observed to happen for:
drivers/xen/gntdev.c: if (__get_user(old_status, batch->status[i]))
where UBSAN added array bound checking.
This complements commit:
6ae865615fc4 ("x86/uaccess: Dont leak the AC flag into __put_user() argument evaluation")
If devm_request_irq() fails to disable all interrupts, no cleanup is
performed before retuning the error. To fix this issue, invoke
omap_dma_free() to do the cleanup.
In ti_dra7_xbar_probe(), 'rsv_events' is allocated through kcalloc(). Then
of_property_read_u32_array() is invoked to search for the property.
However, if this process fails, 'rsv_events' is not deallocated, leading to
a memory leak bug. To fix this issue, free 'rsv_events' before returning
the error.
In commit 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
turbostat could be terminated by general protection fault on some latest
hardwares which (for example) support 9 levels of C-states and show 18
"tADDED" lines. That bloats the total output and finally causes buffer
overrun. So let's extend the buffer to avoid this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When counting dispatched micro-ops with cnt_ctl=1, in order to prevent
sample bias, IBS hardware preloads the least significant 7 bits of
current count (IbsOpCurCnt) with random values, such that, after the
interrupt is handled and counting resumes, the next sample taken
will be slightly perturbed.
The current count bitfield is in the IBS execution control h/w register,
alongside the maximum count field.
Currently, the IBS driver writes that register with the maximum count,
leaving zeroes to fill the current count field, thereby overwriting
the random bits the hardware preloaded for itself.
Fix the driver to actually retain and carry those random bits from the
read of the IBS control register, through to its write, instead of
overwriting the lower current count bits with zeroes.
Tested with:
perf record -c 100001 -e ibs_op/cnt_ctl=1/pp -a -C 0 taskset -c 0 <workload>
Machines prior to family 10h Rev. C don't have the RDWROPCNT capability,
and have the IbsOpCurCnt bitfield reserved, so this patch shouldn't
affect their operation.
It is unknown why commit db98c5faf8cb ("perf/x86: Implement 64-bit
counter support for IBS") ignored the lower 4 bits of the IbsOpCurCnt
field; the number of preloaded random bits has always been 7, AFAICT.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: "Arnaldo Carvalho de Melo" <acme@kernel.org> Cc: <x86@kernel.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Borislav Petkov" <bp@alien8.de> Cc: Stephane Eranian <eranian@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: "Namhyung Kim" <namhyung@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20190826195730.30614-1-kim.phillips@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
A similar workaround for the suspend/resume problem is needed for yet
another ASUS machines, P6X models. Like the previous fix, the BIOS
doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_*
entries are used instead.
Reported-and-tested-by: SteveM <swm@swm1.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
pfn_valid can be wrong when parsing a invalid pfn whose phys address
exceeds BITS_PER_LONG as the MSB will be trimed when shifted.
The issue originally arise from bellowing call stack, which corresponding to
an access of the /proc/kpageflags from userspace with a invalid pfn parameter
and leads to kernel panic.
[46886.723249] c7 [<c031ff98>] (stable_page_flags) from [<c03203f8>]
[46886.723264] c7 [<c0320368>] (kpageflags_read) from [<c0312030>]
[46886.723280] c7 [<c0311fb0>] (proc_reg_read) from [<c02a6e6c>]
[46886.723290] c7 [<c02a6e24>] (__vfs_read) from [<c02a7018>]
[46886.723301] c7 [<c02a6f74>] (vfs_read) from [<c02a778c>]
[46886.723315] c7 [<c02a770c>] (SyS_pread64) from [<c0108620>]
(ret_fast_syscall+0x0/0x28)
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's safer to zero out the password so that it can never be disclosed.
Fixes: 0c219f5799c7 ("cifs: set domainName when a domain-key is used in multiuser") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we use a domain-key to authenticate using multiuser we must also set
the domainnmame for the new volume as it will be used and passed to the server
in the NTLMSSP Domain-name.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
