Tad Davanzo [Sat, 6 Feb 2021 03:42:47 +0000 (22:42 -0500)]
mvebu: venom resize kernel to 6MB
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0x900000, size 0x600000 6291456 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "priKernSize";
priKernSize=0x0600000
Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.
Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.
Tad Davanzo [Sat, 6 Feb 2021 03:38:03 +0000 (22:38 -0500)]
mvebu: mamba resize kernel to 4MB
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0xa00000, size 0x400000 4194304 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "pri_kern_size";
pri_kern_size=0x400000
Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.
Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.
Tony Ambardar [Tue, 2 Mar 2021 01:14:50 +0000 (17:14 -0800)]
iproute2: separate tc into tiny and full variants
This change was investigated previously [1] but not deemed necessary. With
the recent addition [2] of modern BPF loader support, however, tc gained
dependencies on libelf and libbpf, with a larger installation footprint.
Similar to ip-tiny/ip-full, split tc into tc-full and tc-tiny variants,
where the latter excludes the eBPF loader, uses a smaller executable, and
avoids libelf and libbpf package dependencies. Both variants provide the
'tc' virtual package, with tc-tiny as the default.
The previous tc package included a loadable module for iptables actions.
Separate this out into a common package, tc-mod-iptables, which both
variants depend on. Some package sizes on mips_24kc:
Before:
148343 tc_5.11.0-1_mips_24kc.ipk
After:
144833 tc-full_5.11.0-2_mips_24kc.ipk
138430 tc-tiny_5.11.0-2_mips_24kc.ipk (and no libelf or libbpf)
4115 tc-mod-iptables_5.11.0-2_mips_24kc.ipk
Also fix up some Makefile indentation.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447619962
[2] b048a305a3d3 ("iproute2: update to 5.11.0")
Tony Ambardar [Tue, 2 Mar 2021 04:59:04 +0000 (20:59 -0800)]
kernel/modules: relocate teql hotplug from iproute2 to kmod-sched
The link equalizer sch_teql.ko of package kmod-sched relies on a hotplug
script historically included in iproute2's tc package. In previous
discussion [1], consensus was the hotplug script is best located together
with the module in kmod-sched, but this change was deferred at the time.
Relocate the hotplug script now. This change also simplifies adding a tc
variant for minimal size with reduced functionality.
Tony Ambardar [Sat, 13 Mar 2021 04:58:28 +0000 (20:58 -0800)]
iproute2: add missing limits.h includes
This patch has been submitted upstream to fix an error reported by a few
users. One instance seen using gcc 10.2.0, binutils 2.35.1 and musl 1.1.24:
bpf_glue.c: In function 'get_libbpf_version':
bpf_glue.c:46:11: error: 'PATH_MAX' undeclared (first use in this function);
did you mean 'AF_MAX'?
46 | char buf[PATH_MAX], *s;
| ^~~~~~~~
| AF_MAX
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Thu, 18 Mar 2021 07:06:47 +0000 (00:06 -0700)]
kernel: add missing config symbols, fix typos
Update 5.10 generic config to add missing options prompting during builds,
when setting CONFIG_ALL_KMODS. Refresh the x86 subtargets to drop symbols
added to the generic config.
Also fix a typo in 5.4/5.10 generic configs: "CONFIG_CONFIG_KVM_AMD_SEV".
Tony Ambardar [Wed, 17 Mar 2021 07:48:24 +0000 (00:48 -0700)]
kernel: 5.10: add missing dependency in kmod-mdio-devres
Add conditional dependency on kmod-of-mdio due to mdio_devres.c code:
#if IS_ENABLED(CONFIG_OF_MDIO)
...
EXPORT_SYMBOL(devm_of_mdiobus_register);
#endif /* CONFIG_OF_MDIO */
Fixes: 95a3741d17 ("kernel: support new mdio_devres.ko module in 5.10") Reported-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rosen Penev [Sat, 6 Mar 2021 22:17:45 +0000 (14:17 -0800)]
binutils: fix compilation with ccache
For some reason, one of the configure checks results in some infinite
loop and ends up spawning endless gcc processes, causing OOM. Just pass
a configure var to avoid it.
Shiji Yang [Mon, 1 Mar 2021 06:35:12 +0000 (14:35 +0800)]
ramips: improve GPIO pin control for HC5x61
HC5661 does not have USB port, remove usb power control pin.
HC5x61 do not have LAN LEDs, remove ethernet LED control pin.
Only HC5861 has PA in 2.4G channel.
Tony Ambardar [Mon, 15 Mar 2021 23:11:27 +0000 (16:11 -0700)]
tools/sparse: update to version 0.6.3
Update to the latest stable release.
This fixes a segfault and build failure seen compiling the 5.10 kernel
for x86/64. With this update, builds complete and sparse generates the
usual large volume of warnings as on 5.4 kernels.
Reported-by: Javier Marcet <javier@marcet.info> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Eike Ritter [Sun, 14 Mar 2021 18:50:21 +0000 (18:50 +0000)]
ppp: compile fix: unset FILTER variable in Makefile
If the environment variable FILTER is set before compilation,
compilation of the ppp-package will fail with the error message
Package ppp is missing dependencies for the following libraries:
libpcap.so.1
The reason is that the OpenWrt-patch for the Makefile only comments
out the line FILTER=y. Hence the pcap-library will be dynamically
linked if the environment variable FILTER is set elsewhere, which
causes compilation to fail. The fix consists on explicitly unsetting
the variable FILTER instead.
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.
Set maximum kernel size and disable image building for this board.
Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843 Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
David Bauer [Wed, 17 Mar 2021 23:56:02 +0000 (00:56 +0100)]
mediatek: fix broken UniFi 6 LR image
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
David Bauer [Wed, 17 Mar 2021 23:54:25 +0000 (00:54 +0100)]
ramips: fix broken UniFi 6 Lite image
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Daniel Golle [Wed, 17 Mar 2021 17:39:46 +0000 (17:39 +0000)]
uboot-mediatek: bpi-r64: make use of FIT configuration selection
Allow selecting either SATA or PCIE functionality using uImage.FIT
configurations and device-tree overlays.
By default, PCIE1 is selected (as it has been before this change).
To select SATA instead, you can do this now:
Daniel Golle [Wed, 17 Mar 2021 17:36:54 +0000 (17:36 +0000)]
mediatek: bpi-r64: use dt-overlay to select SATA or PCIE1
The Bananapi BPi-R64 got a SATA interface which cannot be used at the
same time as the second mPCIe slot. The decission is made by hogging
GPIO 90.
Embed two addtional DT overlay blobs into the image to allow bootloader
selection of either SATA or PCIE1 feature.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 17 Mar 2021 17:30:48 +0000 (17:30 +0000)]
include/image*: add support for device-tree overlays
Add new target feature 'dt-overlay' which makes DTC keep the symbol
names in the generated dtb.
Make sure additional DT overlay sources specified by the new device
variable DEVICE_DTS_OVERLAY get compiled together with the main DTS
(currently overlays got to be in the same folder). Let Build/fit pass
the generated DT overlay blobs to mkits.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 17 Mar 2021 17:27:55 +0000 (17:27 +0000)]
scripts/mkits.sh: add support for adding DT overlay blobs to image
Allow adding multiple device tree overlay blobs to an image and
generate configurations for each of them.
This is useful on boards with modern U-Boot which allow e.g. user-
configurable peripherals ("shields") in that way.
Note that currently, each generated configuration adds exactly one
overlay on top of the base image, ie. adding multiple overlays at the
same time is not yet supported.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Bjørn Mork [Sat, 13 Mar 2021 16:45:52 +0000 (17:45 +0100)]
realtek: enable HWMON for SFP sensors
This adds SFP sensors as a hwmon device, allowing readout of
temperatures, DOM and other sensor readings available from the
SFP. Example from a ZyXEL GS1900-10HP with a DOM capable
1000Base-SX SFP:
Bjørn Mork [Sat, 13 Mar 2021 16:45:51 +0000 (17:45 +0100)]
realtek: re-enable sfp driver for ZyXEL GS1900-10HP
There is no need to define a static link or a phy for the sfp
ports. Using phy-mode and managed properties to describe the
link to the sfp phy.
We have to keep the now unconnected virtual "phys" because the
switch driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.
Paul Spooren [Tue, 16 Mar 2021 01:59:26 +0000 (15:59 -1000)]
build,ib: add STRIP_ABI option for manifest
The ImageBuilder `make manifest` prints all installed packages. This
function can be used to create a list of package and corresponding
package versions before attempting image creation.
When called with `--strip-abi` OPKG can automatically strip attached
ABIVersions from package names. Make this function accessible for the
ImageBuilder by adding a `STRIP_ABI` variable.
Magnus Kroken [Sun, 14 Mar 2021 18:42:33 +0000 (19:42 +0100)]
mbedtls: update to 2.16.10
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.
Security fixes:
* Fix a buffer overflow in mbedtls_mpi_sub_abs()
* Fix an errorneous estimation for an internal buffer in
mbedtls_pk_write_key_pem()
* Fix a stack buffer overflow with mbedtls_net_poll() and
mbedtls_net_recv_timeout()
* Guard against strong local side channel attack against base64 tables
by making access aceess to them use constant flow code
Full release announcement:
https://github.com/ARMmbed/mbedtls/releases/tag/v2.16.10
Tony Ambardar [Mon, 15 Mar 2021 09:48:46 +0000 (02:48 -0700)]
x86/legacy: fix subtarget CPU for kernel 5.10
The 5.10 target config defined a baseline i686 CPU aligned to the 32-bit
generic subtarget. However, the legacy subtarget arch wasn't set to the
older 586MMX, defaulting instead to the i686.
Explicitly set the subtarget arch and refresh the subtarget config, as done
already with the old geode subtarget.
Fixes: 8391781389 ("x86: support kernel 5.10") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Daniel Golle [Mon, 15 Mar 2021 16:39:20 +0000 (16:39 +0000)]
mediatek: mt7622: drop duplicate DEVICE_PACKAGES
kmod-mt7615e kmod-mt7615-firmware and uboot-envtools are already part
of the target's default package set. No need to add them again for
buffalo_wsr-2533dhp2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
INAGAKI Hiroshi [Sun, 7 Mar 2021 17:36:16 +0000 (18:36 +0100)]
mediatek: add support for Buffalo WSR-2533DHP2
This adds support for the Buffalo WSR-2533DHP2.
The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.
There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image
Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.
Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash
1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.
INAGAKI Hiroshi [Sun, 7 Mar 2021 15:47:17 +0000 (16:47 +0100)]
mtd: add option for TRX magic to fixtrx
Buffalo uses the TRX header with a different magic and even changes this
magic with different devices. This change allows to specify the header
to use as a command line argument.
This is needed for the Buffalo WSR-2533DHP2 based on mt7622.
Andre Heider [Tue, 16 Feb 2021 07:21:08 +0000 (08:21 +0100)]
build: prereq: drop support for Python 3.5
The final Python 3.5 release was 3.5.10 in September 2020 [0].
This release series is now End-of-Life (EOL).
The only LTS distribution that still only ships Python 3.5 is Ubuntu 16.04,
which will be EOL in April 2021 [1].
The meson build system bumped their python requirement to 3.6 for the 0.57.0
release. This patch ensures that OpenWrt can update meson while still
relying on the host python.
Paul Spooren [Thu, 4 Feb 2021 23:34:30 +0000 (13:34 -1000)]
scripts,ipkg-build: apply shellcheck
This commit cleans the `ipkg-build` script via changes suggested by
shellcheck. These are mostly word splitting issues.
Remove the definition of GZIP, this adds three "lookups" of the `gzip`
binary but the rest of the build system doesn't seem to use such
improvements neither.
Daniel Golle [Sun, 14 Mar 2021 19:11:14 +0000 (19:11 +0000)]
mediatek: mt7622: clean up image build
* clean up whitespace to make GPT partitioning more readable
* don't select packages already part of the target default selection
* don't select U-Boot variants (breaks ImageBuilder)
* don't select AHCI on boards without SATA
* don't select kmod-usb2 and kmod-ohci, USB 1.x and USB 2.0 devices
work fine with the in-SoC XHCI host having just kmod-usb3 installed.
* select kmod-btmtkuart for devices with Bluetooth support
* sort DEVICE_PACKAGES
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rafał Miłecki [Sun, 14 Mar 2021 18:22:18 +0000 (19:22 +0100)]
bcm4908: use accepted 5.13 DTS patches
Some patches were slightly cleaned up. One things worth mentioning is
that adding:
phy-mode = "rgmii"
broke SF2 driver. It made it access random register breaking switch
setup.
Hauke Mehrtens [Wed, 27 Jan 2021 21:16:11 +0000 (22:16 +0100)]
realtek: Add ZyXEL GS1900-8
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Dominick Grift [Sun, 14 Mar 2021 11:42:29 +0000 (12:42 +0100)]
selinux-policy: update to version v0.8
3d7da7a igmpproxy tidy some loose ends c84ba0f rcigmpproxy: add entries to /etc when creating /etc/igmpproxy.conf 5a18967 adds igmpproxy skeleton 7e6a218 logread: support resolving dns names e39ca8b netifd: add support for /etc/udhcpc.user 7952bd0 odhcp6c: support /etc/odhcp6c.user ba0eb4e swconfig, fwenv, agent 4556b8a pppd cosmetic 9324d9d pppd: sends AT commands to model using /dev/ttyUSBN 417b14a ttydev: add some more ttyUSB ed739dc example: dont depend on policycoreutils 97613f9 dropbear: using dropbear as scp: dns name resolving 12c193b dropbear tcp connect ssh ports for scp c050077 rcdnsmasq: remove redundant rule and make rcsysntpd optional 8c5de35 this is a bug 8d5c463 uhttpd rcboot rcdnsmasq 094266e hostapd and wpa_supplicant aef0bd7 mountroot: maintains /tmp/sysupgrade.tar 24f0406 dropbear: allow it to read tmp.fs files 2901433 firstboot mkfsf2fs rcboot 2c4afb7 blockmount mmc 465ca98 adds industrial i/o (iio) nodedev 82f686e mtd stordev: back that ubiblock0_4p1 up with a filecon 7df78bd ubus: "support" older ubusd versions that run as root 4458bce swconfig: allow using terminal (to print output) e8d606d sslcert: openssl linked: this shaves off 200 bytes 93afffb jshn ntpdhotplug 0b847f0 wpad: reads /etc/ssl/openssl.cnf f14ee34 indent fix a0c7cad mtd, uhttpd, ubus and ntpdhotplug d74f98f adds a not about checkreqprot requirement in some scenarios affacce example: add policycoreutils-setfiles for make check 4f944dc kmodloader and fwenv: efe36a3 netifd: adds a comment/reminder 581b087 more fw_printenv loose ends 30177a4 fw_setenv: needs mtd write access to set and delete env da28f4c fw_printenv: some minor clean ups a062053 fw_printenv missing rules 244ba5f blockmount: extroot and /rwm 0745a6a squid: allow squid to run sslcrtd with domain transition b851df6 squid fix 8c55acd squid: adds certfile and allow connect http but... b7c1f6d Makefile: exclude tinyproxy from mintesttgt (using squid) 5ff39bd squid: forgot about luci 5366c97 squid/rcsquid some basic fill in 8743da6 squid skeleton 687a43b adds squid 3128 port to httpproxy port
This adds experimental ethernet support for BCM6318, BCM6328, BCM6362, BCM6368
and BCM63268.
BCM6358 needs a different driver, so there's no support for now.
Tony Ambardar [Fri, 12 Mar 2021 01:45:05 +0000 (17:45 -0800)]
tools/libelf: remove unneeded host library
This old ELF library dating to 2009 used to be necessary on MacOS but
is not required for building the kernel or tools since [1]. On Linux
systems, libelf is already an OpenWRT build-system prerequisite [2].
Presence of the older library can mask or conflict with the system libelf
and lead to build errors, as seen compiling Linux kernels since v5.8 or
host tools such as dwarves (e.g. pahole).
Remove the unnecessary tools/libelf library and avoid the related issues.
[1] 5f8e587240 ("build: force disable stack validation during kernel build
on non-linux systems")
[2] https://openwrt.org/docs/guide-developer/build-system/install-buildsystem#prerequisites
Tested-by: Rosen Penev <rosenp@gmail.com> (Linux) Tested-by: Georgi Valkov <gvalkov@abv.bg> (MacOS) Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Tue, 26 Jan 2021 22:37:04 +0000 (14:37 -0800)]
elfutils: remove host build from target package
Commit f4da28c301 ("elfutils: Add host build") supplied a libelf host
library to fix a glib2 host build error, but this need was later removed
by b6212c8769 ("glib2: don't use libelf during host build").
More importantly, there are already two sources for libelf host libraries:
OpenWRT build prerequisites [1] and tools/libelf. A third is not needed.
mvebu: LS421DE: make cosmetics changes in dts file
Make some cosmetic changes in the Buffalo LinkStation LS421DE NAS:
- Delete pointless #xxx-cells
- bootargs: replace earlyprintk with earlycon and remove unneeded args.
- Separate pinmux nodes with empty lines.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
projects / thirdparty / openwrt.git / log
