Commit dc9cc0d3e2a1 ("realtek: add QoS and rate control") replaced a
16 bit reserved field in the RTL83xx packet header with the initial
cpu_tag word, shifting the real cpu_tag fields by one. Adjusting for
this new shift was partially forgotten in the new RX tag decoders.
This caused the switch to block IGMP, effectively blocking IPv4
multicast.
The bug was partially fixed by commit 9d847244d9fd ("realtek: fix
RTL839X receive tag decoding")
Fix on RTL838x too, including correct NIC_RX_REASON_SPECIAL_TRAP value.
Suggested-by: Jan Hoffmann <jan@3e8.eu> Fixes: dc9cc0d3e2a1 ("realtek: add QoS and rate control") Signed-off-by: Bjørn Mork <bjorn@mork.no>
The WWAN card is running a modified version of OpenWrt and handles
power-management as well as the LED controller (AW9523). A root shell
can be acquired by installing adb using opkg and executing "adb shell".
Daniel Golle [Thu, 8 Sep 2022 01:44:30 +0000 (02:44 +0100)]
mediatek: bpi-r64: make initramfs/recovery optional
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 8 Sep 2022 01:34:28 +0000 (02:34 +0100)]
mediatek: bpi-r3: make initramfs/recovery optional
Only include recovery image in SD card image generated for the
BananaPi BPi-R3 if building with CONFIG_TARGET_ROOTFS_INITRAMFS.
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Installation
1. Rename initramfs image to:
openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
reset button. Hold the button, on the lates bootloader version, when
Power and WiFi-5 LEDs will start blinking release it. For the older
bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
minute) the Power LED will start blinking, when stops, router is fully
booted.
4. Connect to one of LAN ports and use SSH to open the shell at
192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
at some point, You want to go back to original firmware. The firmware
provided by manufacturer on its site is encrypted and U-Boot accepts
only decrypted factory images, so there's no way to restore original
firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
LED will start blinking, wait till it stops, then router is ready for
configuration.
Additional information
U-Boot command line is password protected. Password is unknown.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
kernel: load FAT filesystem drivers before mount_root
Devices using GPT usually have FAT filesystem on boot partition and
that's where the intermediary backup of system configuration is stored
on sysupgrade. Automatic restoring of OpenWrt configuration after
sysupgrade will be inhibited if the driver is not loaded and file system
type is not specified in mount command.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Daniel Golle [Wed, 7 Sep 2022 03:23:22 +0000 (04:23 +0100)]
mediatek: remove redundant patch
The patch 921-mt7986-add-mmc-support.patch introduced by commit dabcaac443 ("mediatek: add mt7986 soc support to the target") has never
been applied in a way that it would have any effect as it actually
created a file target/linux/generic/patches-5.15/... in the kernel tree
and was probably a patch intended to be applied to openwrt.git instead
of being put into kernel patches folder as a file.
As an upstream commit from vanilla Linux also adding support for MT7986
to the mtk-sd driver has already been included we can remove that old
patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add another patch found here:
https://github.com/archlinux/svntogit-packages/commit/55b26eda94e1a9ff726ac458fccab5f3f3ad2114
as 003-bc-fix-hang.patch to prevent a hang when building the kernel.
Nick Hainke [Sun, 21 Aug 2022 21:04:58 +0000 (23:04 +0200)]
tools/cmake: refresh patches
Previous commit forgot to refresh the patches.
This commit refreshes the patches:
- 120-curl-fix-libressl-linking.patch
- 130-bootstrap_parallel_make_flag.patch
Fixes: 3b2f19271cc2 ("tools/cmake: update to 3.24.1") Signed-off-by: Nick Hainke <vincent@systemli.org>
Daniel Golle [Mon, 5 Sep 2022 21:41:22 +0000 (22:41 +0100)]
kernel: rework Huawei-compatible OEM SFP GE-T
This patch was added in 09b086eecaa545cf7f30bc7e394a32751e25db65
("kernel: add quirk for Huawei-compatible OEM SFP GE-T"). Add patch
title, description and SoB to follow OpenWrt's developer guide for
working patches to prepare it for being sent upstream. This patch
should be discussed with Russell King and merged to Linux kernel.
Co-authored-by: Josef Schlehofer <pepe.schlehofer@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Josef Schlehofer [Fri, 26 Aug 2022 14:21:44 +0000 (16:21 +0200)]
kernel: add support for HALNy HL-GSFP and other related fixes
It was reported on Turris forum [1] that HALNy HL-GSFP module does not
work as it should with kernel 5.15. Russell King prepared this patch
series, which fixes broken SFP module to work.
Felix Fietkau [Tue, 6 Sep 2022 10:12:12 +0000 (12:12 +0200)]
hostapd: rename hostapd multicast_to_unicast option to multicast_to_unicast_all
There are two feature currently altered by the multicast_to_unicast option.
1. bridge level multicast_to_unicast via IGMP snooping
2. hostapd/mac80211 config multicast_to_unicast setting
The hostapd/mac80211 setting has the side effect of converting *all* multicast
or broadcast traffic into per-station duplicated unicast traffic, which can
in some cases break expectations of various protocols.
It also has been observed to cause ARP lookup failure between stations
connected to the same interface.
The bridge level feature is much more useful, since it only covers actual
multicast traffic managed by IGMP, and it implicitly defaults to 1 already.
Renaming the hostapd/mac80211 option to multicast_to_unicast_all should avoid
unintentionally enabling this feature
Petr Štetiar [Tue, 30 Aug 2022 06:45:39 +0000 (08:45 +0200)]
build: provide xxd -i with scripts/xxdi.pl
Dependency on xxd was added in commit c4dd2441e787 ("tools: add xxd
(from vim)") as U-Boot requires xxd to create the default environment
from an external file.
Later in commit 2b94aac7a128 ("tools: xxd: use more convenient source
tarball"), xxd from another source was used instead, but that source is
currently unavailable, so let's fix it by using simple xxdi.pl Perl
script instead.
Fixes: #10555 Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 30 Aug 2022 06:34:26 +0000 (08:34 +0200)]
scripts: xxdi.pl: add xxd -i compat mode
So it can serve as a standalone drop in replacement for xxd utility used
currently mostly in U-Boot packages with `xxd -i` mode which outputs C
include file style, with aim for byte to byte identical output, so the
eventual difference in the generated output is easily spottable.
Nick Hainke [Fri, 19 Aug 2022 16:59:36 +0000 (18:59 +0200)]
ath79: add low_mem to tiny image
Devices with SMALL_FLASH enabled have "SQUASHFS_BLOCK_SIZE=1024" in
their config. This significantly increases the cache memory required by
squashfs [0]. This commit enables low_mem leading to a much better
performance because the SQUASHFS_BLOCK_SIZE is reduced to 256.
Example Nanostation M5 (XM):
The image size increases by 128 KiB. However, the memory statisitcs look
much better:
ipq40xx: point to externally compiled dtbs in recipes
Adjusting dts will cause a rebuild of whole kernel as the buildroot
considers this a part of kernel source. It's a royal PITA when trying to
prepare support for new device, since this takes a lot of time on slower
systems. As it stands, buildroot itself, with own rule, also compiles
dtbs and the results are $(KDIR)/image-$(DEVICE_DTS).dtb. With setting
DEVICE_DTS_DIR to directory holding the device dts (similarly to some
other targets), buildroot doesn't consider changed dts as part of kernel
source and rebuilds only dtb. This really speeds up development. And
since the kernel built dts are no longer used, drop the paches adding
dtses to its build.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
Still missing:
- Ethernet driver
- Sysupgrade support
A.t.m there exists one subtarget EN7523 with only one evaluation
board.
The initramfs can be run with the following commands from u-boot:
-
u-boot> setenv bootfile \
openwrt-airoha-airoha_en7523-evb-initramfs-kernel.bin
u-boot> tftpboot
u-boot> bootm 0x81800000
-
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
8 and 16 bit writes to the GPIO peripheral are apparently not supported,
and only worked most of the time. This resulted in garbabe writes to the
interrupt mask registers, causing spurious unhandled interrupts, which
could lead to CPU lock-ups as these kept retriggering.
Instead of clearing these spurious interrupt when they occur, the
upstream patch will just make sure all register writes have the intended
result, so these don't happen at all.
Martin Kennedy [Tue, 30 Aug 2022 00:47:24 +0000 (20:47 -0400)]
mpc85xx: Drop pci aliases to avoid domain changes
As of upstream Linux commit 0fe1e96fef0a ("powerpc/pci: Prefer PCI
domain assignment via DT 'linux,pci-domain' and alias"), the PCIe
domain address is no longer numbered by the lowest 16 bits of the PCI
register address after a fallthrough. Instead of the fallthrough, the
enumeration process accepts the alias ID (as determined by
`of_alias_scan()`). This causes e.g.:
... which then causes the sysfs path of the netdev to change,
invalidating the `wifi_device.path`s enumerated in
`/etc/config/wireless`.
One other solution might be to migrate the uci configuration, as was
done for mvebu in commit 0bd5aa89fcf2 ("mvebu: Migrate uci config to
new PCIe path"). However, there are concerns that the sysfs path will
change once again once some upstream patches[^2][^3] are merged and
backported (and `CONFIG_PPC_PCI_BUS_NUM_DOMAIN_DEPENDENT` is enabled).
Instead, remove the aliases and allow the fallthrough to continue for
now. We will provide a migration in a later release.
Fixes: #10530 Tested-by: Martin Kennedy <hurricos@gmail.com>
[Tested on the Aerohive HiveAP 330 and Extreme Networks WS-AP3825i] Signed-off-by: Martin Kennedy <hurricos@gmail.com>
at91bootstrap: use sdmmc0 as booting media for sama5d27_som1_ek
Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as
default defconfig") changed default booting media for sama5d27_som1_ek
board w/o any reason. Changed it back to sdmmc0 as it is for all the
other Microchip supported distributions for this board (Buildroot,
Yocto Project). The initial commit cannot be cleanly reverted.
uboot-at91: use sdmmc0 as booting media for sama5d27_som1_ek
Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs")
changed the booting media to sdmmc1 as default booting w/o any reason.
The Microchip releases for the rest of supported distributions (Buildroot,
Yocto Project) uses sdmmc0 as default booting media for this board.
Thus change it back to sdmmc0. With this remove references to sdmmc1
config. The initial commit cannot be cleanly reverted.
Felix Fietkau [Thu, 1 Sep 2022 18:41:42 +0000 (20:41 +0200)]
unetd: update to the latest version
f5d02c32f811 pex: add support for sending endpoint notification from the wg port via raw socket c3b1127236a0 ubus: add support for querying active networks 8ad119715168 ubus: add support for adding auth_connect hosts at runtime 26dc52789d41 network: add support for configuring extra peers via a separate json file d7fb9e5b065b ubus: add reload command
f5fcdcf cli: introduce test mode and refuse firewall restart on errors a540f6d fw4: fix cosmetic issue with per-ruleset and per-table include paths 695e821 doc: fix swapped include positions in nftables.d README
Daniel Golle [Wed, 31 Aug 2022 12:31:02 +0000 (13:31 +0100)]
uboot-mediatek: replace patches with updated versions
Weijie Gao has submitted an updated version of the patchset adding
support for MT7986 and MT7981 to U-Boot. Use that v2 patchset.
Changes of v2:
- Add cpu driver for print_cpuinfo()
- Fix NULL pointer dereference in mtk_image
(was already fixed in OpenWrt)
- Fix coding style
- Minor changes
Daniel Golle [Wed, 13 Jul 2022 03:30:32 +0000 (04:30 +0100)]
mediatek: add support for Bananapi BPi-R3
The Bananapi BPi-R3 is a development router board built around the
MediaTek Filogic 830 (MT7986A) SoC.
The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC.
Only either SPI-NAND or SPI-NOR can be used at the same time, also only
either microSD or eMMC can be used. The various storage options can be
selected using small SMD switches on the board.
Working:
* all 4 boot methods incl. installation via U-Boot, sysupgrade, ...
* copper LAN and WAN ports
* SFP1 (connected to gmac1, eth1 in Linux)
* WiFi
* LEDs
* Buttons
* PSTORE/ramoops based dual-boot
Not Working (missing driver features):
* SFP2 (connected to MT7531 switch)
Daniel Golle [Wed, 13 Jul 2022 03:29:34 +0000 (04:29 +0100)]
uboot-mediatek: add support for Bananapi BPi-R3
The Bananapi BPi-R3 board can boot from eMMC, SD card, SPI-NAND and
SPI-NOR, depending on the position of switches controlling the BOOTSEL
bootstrap pins as we as hard-wired chip-select lines. The position of the
chip-select switch SW6 decides whether either SD card or eMMC can be
accessed, SW5 selects either SPI-NAND or SPI-NOR.
Generate U-Boot for all 4 boot options. The SD card version allows
installation to SPI-NAND and SPI-NOR (eMMC cannot be accessed
simultanously with the SD card), the SPI-NAND version allows installation
to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 15 Aug 2022 16:50:10 +0000 (18:50 +0200)]
kernel: add pending mtk_sgmii and phy improvements from @lynxis
Add pending patches from Alexander 'lynxis' Couzens which are required
for RealTek NBase-T PHYs or SFP+ cages to work when connected to the
SGMII interface provided by recent MediaTek SoCs [1].
The patches for MT753x fix link speed limitation on CPU ports observed
by many users which is due to reset being carried out wrongly [2].
Felix Fietkau [Tue, 30 Aug 2022 08:57:26 +0000 (10:57 +0200)]
mac80211: disable ft-over-ds by default
Testing has shown it to be very unreliable in variety of configurations.
It is not mandatory, so let's disable it by default until we have a better
solution.
Felix Fietkau [Mon, 29 Aug 2022 18:54:28 +0000 (20:54 +0200)]
unetd: update to the latest version, makes VXLAN/eBPF optional
b75791a6db25 scripts/update-cmd.pl: reorder add/remove calls to better deal with dynamic changes c29e1ad045d0 scripts/update-cmd.pl: set device up before adding routes/addresses 5ad35ce4beea scripts/update-cmd.pl: run update two times 5d79b88f00c1 add support for overriding peer-exchange-port for individual hosts 0041fcacb624 add support for disabling VXLAN/eBPF support
The SG2008P has its ethernet ports in the rear, and LEDs in the front.
The ports should be labeled lan8->lan1, not lan1->lan8. To resolve
this, fix the phy mapping in the "ports" node.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
realtek: tl-sg2008p: use correct i2c address for TPS23861
Address 0x30 is a "broadcast" address for the TPS23861. It should not
be used by drivers, as all TPS23861 devices on the bus are supposed to
respond. Change this to the correct address, 0x28.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Sander Vanheule [Mon, 29 Aug 2022 06:23:49 +0000 (08:23 +0200)]
realtek: ignore disabled switch ports
When marking a switch port as disabled in the device tree, by using
'status = "disabled";', the switch driver fails on boot, causing a
restart:
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 802c3064, ra == 8022b4b4
[ ... ]
Call Trace:
[<802c3064>] strlen+0x0/0x2c
[<8022b4b4>] start_creating.part.0+0x78/0x194
[<8022bd3c>] debugfs_create_dir+0x44/0x1c0
[<80396dfc>] rtl838x_dbgfs_port_init+0x54/0x258
[<80397508>] rtl838x_dbgfs_init+0xe0/0x56c
This is caused by the DSA subsystem (mostly) ignoring the port, while
rtl83xx_mdio_probe() still extracts some details on this disabled port
from the device tree, resulting in the usage of a NULL pointer where a
port name is expected.
By not probing ignoring disabled ports, no attempt is made to create a
debugfs directory later. The device then boots as expected without the
disabled port.
Felix Fietkau [Sun, 28 Aug 2022 20:31:05 +0000 (22:31 +0200)]
unetd: update to the latest version
5cbd55f60346 unet-cli: fix formatting of help text 59b97448b636 build.sh: force use of -fPIC on static libraries to fix build error 74a14c00abb0 pex-msg: fix siphash key initializer
projects / thirdparty / openwrt.git / log
