The io_setup takes a pointer to a context id of type aio_context_t.
This in turn is typed to a __kernel_ulong_t. We could tweak the
exported headers to define this as a 64bit quantity for specific
ABIs, but since we already have a 32bit compat shim for the x86 ABI,
let's just re-use that logic. The libaio package is also written to
expect this as a pointer type, so a compat shim would simplify that.
The io_submit func operates on an array of pointers to iocb structs.
Padding out the array to be 64bit aligned is a huge pain, so convert
it over to the existing compat shim too.
We don't convert io_getevents to the compat func as its only purpose
is to handle the timespec struct, and the x32 ABI uses 64bit times.
With this change, the libaio package can now pass its testsuite when
built for the x32 ABI.
It is not safe to use LAR to filter when to go down the espfix path,
because the LDT is per-process (rather than per-thread) and another
thread might change the descriptors behind our back. Fortunately it
is always *safe* (if a bit slow) to go down the espfix path, and a
32-bit LDT stack segment is extremely rare.
This should be a plain old '&' and could easily lead to undefined
behaviour if the target of a pmd_mknotpresent invocation was the same
as the parameter.
Arm64 does not define dma_get_required_mask() function.
Therefore, it should not define the ARCH_HAS_DMA_GET_REQUIRED_MASK.
This causes build errors in some device drivers (e.g. mpt2sas)
Whilst native arm64 applications don't have the 16-bit UID/GID syscalls
wired up, compat tasks can still access them. The 16-bit wrappers for
these syscalls use __kernel_old_uid_t and __kernel_old_gid_t, which must
be 16-bit data types to maintain compatibility with the 16-bit UIDs used
by compat applications.
This patch defines 16-bit __kernel_old_{gid,uid}_t types for arm64
instead of using the 32-bit types provided by asm-generic.
If f2fs_write_data_page is called through the reclaim path, we should submit
the bio right away.
This patch resolves the following issue that Marc Dietrich reported.
"It took me a while to bisect a problem which causes my ARM (tegra2) netbook to
frequently stall for 5-10 seconds when I enable EXA acceleration (opentegra
experimental ddx)."
And this patch fixes that.
Reported-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In various areas of the code, it is assumed that
se_cmd->data_length describes pure data. In case
that protection information exists over the wire
(protect bits is are on) the target core re-calculates
the data length from the CDB and the backed device
block size (instead of each transport peeking in the cdb).
Modify loopback device to include protection information
in the transferred data length (like other scsi transports).
In case protection information exists over the wire
iscsi header data length is required to include it.
Use protection information aware scsi helpers to set
the correct transfer length.
In order to avoid breakage, remove iser transfer length
checks for each task as they are not always true and
somewhat redundant anyway.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Acked-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case protection information exists on the wire
scsi transports should include it in the transfer
byte count (even if protection information does not
exist in the host memory space). This helper will
compute the total transfer length from the scsi
command data length and protection attributes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.
Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.
This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:
In case the transport is iser we should not include the
iscsi target info in the sendtargets text response pdu.
This causes sendtargets response to include the target
info twice.
Modify iscsit_build_sendtargets_response to filter
transport types that don't match.
In case the discovery session is carried over iser, we can't
access the assumed network portal since the default portal is
used. In this case we don't really need to allocate the fastreg
pool, just prepare to the text pdu that will follow.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Reported-by: Alex Tabachnik <alext@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a iscsi_queue_req memory leak when ABORT_TASK response
has been queued by TFO->queue_tm_rsp() -> lio_queue_tm_rsp() after a
long standing I/O completes, but the connection has already reset and
waiting for cleanup to complete in iscsit_release_commands_from_conn()
-> transport_generic_free_cmd() -> transport_wait_for_tasks() code.
It moves iscsit_free_queue_reqs_for_conn() after the per-connection command
list has been released, so that the associated se_cmd tag can be completed +
released by target-core before freeing any remaining iscsi_queue_req memory
for the connection generated by lio_queue_tm_rsp().
Cc: Thomas Glanzmann <thomas@glanzmann.de> Cc: Charalampos Pournaris <charpour@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug where multiple waiters on ->t_transport_stop_comp
occurs due to a concurrent ABORT_TASK and session reset both invoking
transport_wait_for_tasks(), while waiting for the associated se_cmd
descriptor backend processing to complete.
For this case, complete_all() should be invoked in order to wake up
both waiters in core_tmr_abort_task() + transport_generic_free_cmd()
process contexts.
Cc: Thomas Glanzmann <thomas@glanzmann.de> Cc: Charalampos Pournaris <charpour@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug where se_cmd descriptors associated with a
Task Management Request (TMR) where not setting CMD_T_ACTIVE before
being dispatched into target_tmr_work() process context.
This is required in order for transport_generic_free_cmd() ->
transport_wait_for_tasks() to wait on se_cmd->t_transport_stop_comp
if a session reset event occurs while an ABORT_TASK is outstanding
waiting for another I/O to complete.
Cc: Thomas Glanzmann <thomas@glanzmann.de> Cc: Charalampos Pournaris <charpour@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 4 RDMA_CM events that all basically mean that
the user should teardown the IB connection:
- DISCONNECTED
- ADDR_CHANGE
- DEVICE_REMOVAL
- TIMEWAIT_EXIT
Only in DISCONNECTED/ADDR_CHANGE it makes sense to
call rdma_disconnect (send DREQ/DREP to our initiator).
So we keep the same teardown handler for all of them
but only indicate calling rdma_disconnect for the relevant
events.
This patch also removes redundant debug prints for each single
event.
v2 changes:
- Call isert_disconnected_handler() for DEVICE_REMOVAL (Or + Sag)
In ungraceful teardowns isert close flows seem racy such that
isert_wait_conn hangs as RDMA_CM_EVENT_DISCONNECTED never
gets invoked (no one called rdma_disconnect).
Both graceful and ungraceful teardowns will have rx flush errors
(isert posts a batch once connection is established). Once all
flush errors are consumed we invoke isert_wait_conn and it will
be responsible for calling rdma_disconnect. This way it can be
sure that rdma_disconnect was called and it won't wait forever.
This patch also removes the logout_posted indicator. either the
logout completion was consumed and no problem decrementing the
post_send_buf_count, or it was consumed as a flush error. no point
of keeping it for isert_wait_conn as there is no danger that
isert_conn will be accidentally removed while it is running.
(Drop unnecessary sleep_on_conn_wait_comp check in
isert_cq_rx_comp_err - nab)
When checking whether a legacy link key provides at least HIGH security
level we also need to check for FIPS level which is one step above HIGH.
This patch fixes a missing check in the hci_link_key_request_evt()
function.
Due to recent changes to the way that the MITM requirement is set for
outgoing pairing attempts we can no longer rely on the hcon->auth_type
variable (which is actually good since it was formed from BR/EDR
concepts that don't really exist for SMP).
To match the logic that BR/EDR now uses simply rely on the local IO
capability and/or needed security level to set the MITM requirement for
outgoing pairing requests.
When checking whether we need to request authentication or not we should
include HCI_SECURITY_FIPS to the levels that always need authentication.
This patch fixes check for it in the hci_outgoing_auth_needed()
function.
We have found a programming error causing a deadlock in Bluetooth subsystem
of Linux kernel. The problem is caused by missing release_sock() call when
L2CAP connection creation fails due full accept queue.
The issue can be reproduced with 3.15-rc5 kernel and is also present in
earlier kernels.
-[0x02 Details
The problem occurs when multiple L2CAP connections are created to a PSM which
contains listening socket (like SDP) and left pending, for example,
configuration (the underlying ACL link is not disconnected between
connections).
When L2CAP connection request is received and listening socket is found the
l2cap_sock_new_connection_cb() function (net/bluetooth/l2cap_sock.c) is called.
This function locks the 'parent' socket and then checks if the accept queue
is full.
1178 lock_sock(parent);
1179
1180 /* Check for backlog size */
1181 if (sk_acceptq_is_full(parent)) {
1182 BT_DBG("backlog full %d", parent->sk_ack_backlog);
1183 return NULL;
1184 }
If case the accept queue is full NULL is returned, but the 'parent' socket
is not released. Thus when next L2CAP connection request is received the code
blocks on lock_sock() since the parent is still locked.
Also note that for connections already established and waiting for
configuration to complete a timeout will occur and l2cap_chan_timeout()
(net/bluetooth/l2cap_core.c) will be called. All threads calling this
function will also be blocked waiting for the channel mutex since the thread
which is waiting on lock_sock() alread holds the channel mutex.
We were able to reproduce this by sending continuously L2CAP connection
request followed by disconnection request containing invalid CID. This left
the created connections pending configuration.
After the deadlock occurs it is impossible to kill bluetoothd, btmon will not
get any more data etc. requiring reboot to recover.
-[0x03 Fix
Releasing the 'parent' socket when l2cap_sock_new_connection_cb() returns NULL
seems to fix the issue.
Signed-off-by: Jukka Taimisto <jtt@codenomicon.com> Reported-by: Tommi Mäkilä <tmakila@codenomicon.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The universal/local bit handling was incorrectly done in the code.
So when setting EUI address from BD address we do this:
- If BD address type is PUBLIC, then we clear the universal bit
in EUI address. If the address type is RANDOM, then the universal
bit is set (BT 6lowpan draft chapter 3.2.2)
- After this we invert the universal/local bit according to RFC 2464
When figuring out BD address we do the reverse:
- Take EUI address from stateless IPv6 address, invert the
universal/local bit according to RFC 2464
- If universal bit is 1 in this modified EUI address, then address
type is set to RANDOM, otherwise it is PUBLIC
Note that 6lowpan_iphc.[ch] does the final toggling of U/L bit
before sending or receiving the network packet.
In of_init_opp_table function, if a failure to add an OPP is
detected, the count of OPPs, yet to be added is not updated.
Fix this by decrementing this count on failure as well.
Fixes: commit 0611c41934ab35ce84dea34ab291897ad3cbc7be
ARM: OMAP2+: gpmc: update gpmc_hwecc_bch_capable() for new platforms and ECC schemes
Though the commit log of above commit mentions AM43xx platforms, but code change
missed AM43xx. This patch adds AM43xx to list of those SoC which have built-in
ELM hardware engine, so that BCH ecc-schemes with hardware error-correction can
be enabled on AM43xx devices.
Reported-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enable LPAE and big-endian in a hisilicon board, while specify
mem=384M mem=512M@7680M, will get bad page state:
Freeing unused kernel memory: 180K (c0466000 - c0493000)
BUG: Bad page state in process init pfn:fa442
page:c7749840 count:0 mapcount:-1 mapping: (null) index:0x0
page flags: 0x40000400(reserved)
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 3.10.27+ #66
[<c000f5f0>] (unwind_backtrace+0x0/0x11c) from [<c000cbc4>] (show_stack+0x10/0x14)
[<c000cbc4>] (show_stack+0x10/0x14) from [<c009e448>] (bad_page+0xd4/0x104)
[<c009e448>] (bad_page+0xd4/0x104) from [<c009e520>] (free_pages_prepare+0xa8/0x14c)
[<c009e520>] (free_pages_prepare+0xa8/0x14c) from [<c009f8ec>] (free_hot_cold_page+0x18/0xf0)
[<c009f8ec>] (free_hot_cold_page+0x18/0xf0) from [<c00b5444>] (handle_pte_fault+0xcf4/0xdc8)
[<c00b5444>] (handle_pte_fault+0xcf4/0xdc8) from [<c00b6458>] (handle_mm_fault+0xf4/0x120)
[<c00b6458>] (handle_mm_fault+0xf4/0x120) from [<c0013754>] (do_page_fault+0xfc/0x354)
[<c0013754>] (do_page_fault+0xfc/0x354) from [<c0008400>] (do_DataAbort+0x2c/0x90)
[<c0008400>] (do_DataAbort+0x2c/0x90) from [<c0008fb4>] (__dabt_usr+0x34/0x40)
The bad pfn:fa442 is not system memory(mem=384M mem=512M@7680M), after debugging,
I find in page fault handler, will get wrong pfn from pte just after set pte,
as follow:
do_anonymous_page()
{
...
set_pte_at(mm, address, page_table, entry);
//read out the pte just set
new_pte = pte_offset_map(pmd, address);
new_pfn = pte_pfn(*new_pte);
pr_info("new pfn:0x%lx, new pte:0x%llxn", pfn, pte_val(entry));
...
}
pfn: 0x1fa4f5, pte:0xc00001fa4f575f
new_pfn:0xfa4f5, new_pte:0xc00000fa4f5f5f //new pfn/pte is wrong.
The bug is happened in cpu_v7_set_pte_ext(ptep, pte):
An LPAE PTE is a 64bit quantity, passed to cpu_v7_set_pte_ext in the r2 and r3 registers.
On an LE kernel, r2 contains the LSB of the PTE, and r3 the MSB.
On a BE kernel, the assignment is reversed.
Unfortunately, the current code always assumes the LE case,
leading to corruption of the PTE when clearing/setting bits.
This patch fixes this issue much like it has been done already in the
cpu_v7_switch_mm case.
Signed-off-by: Jianguo Wu <wujianguo@huawei.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because the stack trace code includes the stack frames for itself.
This is incorrect behaviour, and also leads to "skip" doing the wrong
thing (which is the number of stack frames to avoid recording.)
Perversely, it does the right thing when passed a non-current thread. Fix
this by ensuring that we have a known constant number of frames above the
main stack trace function, and always skip these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that when you quit tvtime it calls STREAMOFF, but then it queues a
bunch of buffers for no good reason before closing the file descriptor.
In the past closing the fd would free the vb queue since that was part of the file
handle struct. Since that was moved to the global struct that no longer happened.
This wouldn't be a problem, but the extra QBUF calls that tvtime does meant that
the buffer list in videobuf (q->stream) contained buffers, so REQBUFS would fail
with -EBUSY.
The solution is to init the list head explicitly when releasing the file
descriptor and to not free the video resource when calling streamoff.
The real fix will hopefully go into kernel 3.16 when the vb2 conversion is
merged. Basically the saa7134 driver with the old videobuf is so full of holes it
ain't funny anymore, so consider this a band-aid for kernels 3.14 and 15.
timestamps in v4l2 buffers returned to userspace are updated in
uvc_video_clock_update() which uses timestamps fetched from
uvc_video_clock_decode() by calling unconditionally ktime_get_ts().
Hence setting the module clock param to realtime has no effect before
this patch.
When the rtmutex fast path is enabled the slow unlock function can
create the following situation:
spin_lock(foo->m->wait_lock);
foo->m->owner = NULL;
rt_mutex_lock(foo->m); <-- fast path
free = atomic_dec_and_test(foo->refcnt);
rt_mutex_unlock(foo->m); <-- fast path
if (free)
kfree(foo);
spin_unlock(foo->m->wait_lock); <--- Use after free.
Plug the race by changing the slow unlock to the following scheme:
while (!rt_mutex_has_waiters(m)) {
/* Clear the waiters bit in m->owner */
clear_rt_mutex_waiters(m);
owner = rt_mutex_owner(m);
spin_unlock(m->wait_lock);
if (cmpxchg(m->owner, owner, 0) == owner)
return;
spin_lock(m->wait_lock);
}
So in case of a new waiter incoming while the owner tries the slow
path unlock we have two situations:
Even in the case when deadlock detection is not requested by the
caller, we can detect deadlocks. Right now the code stops the lock
chain walk and keeps the waiter enqueued, even on itself. Silly not to
yell when such a scenario is detected and to keep the waiter enqueued.
Return -EDEADLK unconditionally and handle it at the call sites.
The futex calls return -EDEADLK. The non futex ones dequeue the
waiter, throw a warning and put the task into a schedule loop.
Tagged for stable as it makes the code more robust.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Brad Mouring <bmouring@ni.com> Link: http://lkml.kernel.org/r/20140605152801.836501969@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we walk the lock chain, we drop all locks after each step. So the
lock chain can change under us before we reacquire the locks. That's
harmless in principle as we just follow the wrong lock path. But it
can lead to a false positive in the dead lock detection logic:
T0 holds L0
T0 blocks on L1 held by T1
T1 blocks on L2 held by T2
T2 blocks on L3 held by T3
T4 blocks on L4 held by T4
lock T2 -> lock L0 -> deadlock detected, but it's not a deadlock at all.
Brad tried to work around that in the deadlock detection logic itself,
but the more I looked at it the less I liked it, because it's crystal
ball magic after the fact.
We actually can detect a chain change very simple:
Commit 66345d5f79fc (ACPI / ia64 / sba_iommu: Use ACPI scan handler
for device discovery) changed the ordering of SBA (System Bus Adapter)
IOMMU initialization with respect to the PCI host bridge initialization
which broke things inadvertently, because the SBA IOMMU initialization
code has to run after the PCI host bridge has been initialized.
Fix that by reworking the SBA IOMMU ACPI scan handler so that it
claims the discovered matching ACPI device objects without attempting
to initialize anything and move the entire SBA IOMMU initialization
to sba_init() that runs after the PCI bus has been enumerated.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=76691 Fixes: 66345d5f79fc (ACPI / ia64 / sba_iommu: Use ACPI scan handler for device discovery) Reported-and-tested-by: Émeric Maschino <emeric.maschino@gmail.com> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After relatively recent changes in the ACPI-based PCI hotplug
(ACPIPHP) code, the acpiphp_check_host_bridge() executed for PCI
host bridges via acpi_pci_root_scan_dependent() doesn't do anything
useful, because those bridges do not have hotplug contexts. That
happens by mistake, so fix it by making acpiphp_enumerate_slots()
add hotplug contexts to PCI host bridges too and modify
acpiphp_remove_slots() to drop those contexts for host bridges
as appropriate.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=76901 Fixes: 2d8b1d566a5f (ACPI / hotplug / PCI: Get rid of check_sub_bridges()) Reported-and-tested-by: Gavin Guo <gavin.guo@canonical.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
References: https://bugs.acpica.org/show_bug.cgi?id=1077 Signed-off-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1a699476e258 ("ACPI / hotplug / PCI: Hotplug notifications
from acpi_bus_notify()") added debug messages for a few common
events. These debug messages are unconditionally enabled if
CONFIG_DYNAMIC_DEBUG is defined, contrary to the documented
meaning, making the ACPI system spew lots of unwanted noise on
any kernel with dynamic debugging.
The bug was introduced by commit fbfddae69657 ("ACPI: Add
acpi_handle_<level>() interfaces"), which added the
CONFIG_DYNAMIC_DEBUG dependency without respecting its meaning.
Fix by adding real support for dynamic_debug.
Fixes: fbfddae69657 ("ACPI: Add acpi_handle_<level>() interfaces") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_COMMON_CLK is not enabled on S5PV210 platform, so include
some clk API data structures conditionally to avoid compilation
errors. These #ifdefs will be removed for next kernel release,
when the S5PV210 platform moves to DT and the common clk API.
Ensure dma_free_coherent() is not called with incorrect arguments
and only when the memory was actually allocated. This will prevent
possible crashes on error paths of the top level media device driver,
when fimc-is device gets unregistered and its driver detached.
Currently stk1160_read_reg() uses a stack-allocated char to get the
read control value. This is wrong because usb_control_msg() requires
a kmalloc-ed buffer.
This commit fixes such issue by kmalloc'ating a 1-byte buffer to receive
the read value.
While here, let's remove the urb_buf array which was meant for a similar
purpose, but never really used.
Only call usb_autopm_put_interface() if the corresponding
usb_autopm_get_interface() was successful.
This prevents a potential runtime PM counter imbalance should
usb_autopm_get_interface() fail. Note that the USB PM usage counter is
reset when the interface is unbound, but that the runtime PM counter may
be left unbalanced.
Also add comment on why we don't need to worry about racing
resume/suspend on autopm_get failures.
Fixes: d5fd650cfc7f ("usb: serial: prevent suspend/resume from racing
against probe/remove")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that needs_remote_wake up is always set when there are open
ports.
Currently close() would unconditionally set needs_remote_wakeup to 0
even though there might still be open ports. This could lead to blocked
input and possibly dropped data on devices that do not support remote
wakeup (and which must therefore not be runtime suspended while open).
Add an open_ports counter (protected by the susp_lock) and only clear
needs_remote_wakeup when the last port is closed.
Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The delayed-write queue was never emptied on disconnect, something which
would lead to leaked urbs and transfer buffers if the device is
disconnected before being runtime resumed due to a write.
Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither the transfer buffer or the urb itself were released in the
resume error path for delayed writes. Also on errors, the remainder of
the queue was not even processed, which leads to further urb and buffer
leaks.
The same error path also failed to balance the outstanding-urb counter,
something which results in degraded throughput or completely blocked
writes.
Fix this by releasing urb and buffer and balancing counters on errors,
and by always processing the whole queue even when submission of one urb
fails.
Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix use after free or NULL-pointer dereference during suspend and
resume.
The port data may never have been allocated (port probe failed)
or may already have been released by port_remove (e.g. driver is
unloaded) when suspend and resume are called.
Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep trying to submit urbs rather than bail out on first read-urb
submission error, which would also prevent I/O for any further ports
from being resumed.
Instead keep an error count, for all types of failed submissions, and
let USB core know that something went wrong.
Also make sure to always clear the suspended flag. Currently a failed
read-urb submission would prevent cached writes as well as any
subsequent writes from being submitted until next suspend-resume cycle,
something which may not even necessarily happen.
Note that USB core currently only logs an error if an interface resume
failed.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt urb was submitted unconditionally at resume, something
which could lead to a NULL-pointer dereference in the urb completion
handler as resume may be called after the port and port data is gone.
Fix this by making sure the interrupt urb is only submitted and active
when the port is open.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The delayed-write queue was never emptied at shutdown (close), something
which could lead to leaked urbs if the port is closed before being
runtime resumed due to a write.
When this happens the output buffer would not drain on close
(closing_wait timeout), and after consecutive opens, writes could be
corrupted with previously buffered data, transfered with reduced
throughput or completely blocked.
Note that unbusy_queued_urb() was simply moved out of CONFIG_PM.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.
Specifically, suspend() releases the susp_lock after determining the
device is idle but before setting the suspended flag, thus leaving a
window where a concurrent write() can submit an urb.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We find a race between write and resume. usb_wwan_resume run play_delayed()
and spin_unlock, but intfdata->suspended still is not set to zero.
At this time usb_wwan_write is called and anchor the urb to delay
list. Then resume keep running but the delayed urb have no chance
to be commit until next resume. If the time of next resume is far
away, tty will be blocked in tty_wait_until_sent during time. The
race also can lead to writes being reordered.
This patch put play_Delayed and intfdata->suspended together in the
spinlock, it's to avoid the write race during resume.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: xiao jin <jin.xiao@intel.com> Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com> Reviewed-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enable usb serial for modem data, sometimes the tty is blocked
in tty_wait_until_sent because portdata->out_busy always is set and
have no chance to be cleared.
We find a bug in write error path. usb_wwan_write set portdata->out_busy
firstly, then try autopm async with error. No out urb submit and no
usb_wwan_outdat_callback to this write, portdata->out_busy can't be
cleared.
This patch clear portdata->out_busy if usb_wwan_write try autopm async
with error.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: xiao jin <jin.xiao@intel.com> Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com> Reviewed-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I had occasional screen corruption with the matrox framebuffer driver and
I found out that the reason for the corruption is that the hardware
blitter accesses the videoram while it is being written to.
The matrox driver has a macro WaitTillIdle() that should wait until the
blitter is idle, but it sometimes doesn't work. I added a dummy read
mga_inl(M_STATUS) to WaitTillIdle() to fix the problem. The dummy read
will flush the write buffer in the PCI chipset, and the next read of
M_STATUS will return the hardware status.
Since applying this patch, I had no screen corruption at all.
The variable "size" is expressed as number of blocks and not as
number of clusters, this could trigger a kernel panic when using
ext4 with the size of a cluster different from the size of a block.
xfstests generic/091 is failing when mounting ext4 with data=journal.
I think that this regression is same problem that occurred prior to collapse
range issue. So ZERO RANGE also need to call ext4_force_commit as
collapse range.
Tail of a page straddling inode size must be zeroed when being written
out due to POSIX requirement that modifications of mmaped page beyond
inode size must not be written to the file. ext4_bio_write_page() did
this only for blocks fully beyond inode size but didn't properly zero
blocks partially beyond inode size. Fix this.
The problem has been uncovered by mmap_11-4 test in openposix test suite
(part of LTP).
Reported-by: Xiaoguang Wang <wangxg.fnst@cn.fujitsu.com> Fixes: 5a0dc7365c240 Fixes: bd2d0210cf22f CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we perform a data integrity sync we tag all the dirty pages with
PAGECACHE_TAG_TOWRITE at start of ext4_da_writepages. Later we check
for this tag in write_cache_pages_da and creates a struct
mpage_da_data containing contiguously indexed pages tagged with this
tag and sync these pages with a call to mpage_da_map_and_submit. This
process is done in while loop until all the PAGECACHE_TAG_TOWRITE
pages are synced. We also do journal start and stop in each iteration.
journal_stop could initiate journal commit which would call
ext4_writepage which in turn will call ext4_bio_write_page even for
delayed OR unwritten buffers. When ext4_bio_write_page is called for
such buffers, even though it does not sync them but it clears the
PAGECACHE_TAG_TOWRITE of the corresponding page and hence these pages
are also not synced by the currently running data integrity sync. We
will end up with dirty pages although sync is completed.
This could cause a potential data loss when the sync call is followed
by a truncate_pagecache call, which is exactly the case in
collapse_range. (It will cause generic/127 failure in xfstests)
To avoid this issue, we can use set_page_writeback_keepwrite instead of
set_page_writeback, which doesn't clear TOWRITE tag.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
S2MPA01 supports enabling/disabling ramp delay only for buck[1234].
Other bucks have ramp delay enabled always.
However the bit shift for enabling buck4 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[56789] and buck10), the ramp delay for buck4 was also enabled.
Fixes: f7b1a8dc1c1c ("regulator: s2mpa01: Don't check enable_shift before setting enable ramp rate") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
S2MPS11 supports enabling/disabling ramp delay only for buck[2346].
Other bucks have ramp delay enabled always.
However the bit shift for enabling buck6 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[15789] and buck10), the ramp delay for buck6 was also enabled.
Fixes: b96244fad953 ("regulator: s2mps11: Don't check enable_shift before setting enable ramp rate") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the register for ramp delay of buck1 regulator. Buck1 and buck6
share the field (offset 4) in ramp delay register S2MPA01_REG_RAMP2.
The driver used the same register and field for ramp delay of buck3 and
buck1. This lead to updating of ramp delay of buck3 when setting buck1
and actually the ramp delay of buck1 was never set.
Fixes: f18792714608 ("regulator: Add support for S2MPA01 regulator") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRB might be 96 bytes if the extended-I/O-measurement facility is
used. This feature is currently not used by Linux, but struct irb
already has the emw defined. So let's make the irb in lowcore match the
size of the internal data structure to be future proof.
We also have to add a pad, to correctly align the paste.
The bigger irb field also circumvents a bug in some QEMU versions that
always write the emw field on test subchannel and therefore destroy the
paste definitions of this CPU. Running under these QEMU version broke
some timing functions in the VDSO and all users of these functions,
e.g. some JREs.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Sebastian Ott <sebott@linux.vnet.ibm.com> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Analog to git commit 28b92e09e25bdc0ae864b22eacf195a74f861389
first cast tk->wall_to_monotonic.tv_nsec to u64 before doing
the shift with tk->shift to avoid loosing relevant bits on a
32-bit kernel.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
idr_replace() open-codes the logic to calculate the maximum valid ID
given the height of the idr tree; unfortunately, the open-coded logic
doesn't account for the fact that the top layer may have unused slots
and over-shifts the limit to zero when the tree is at its maximum
height.
The following test code shows it fails to replace the value for
id=((1<<27)+42):
static void test5(void)
{
int id;
DEFINE_IDR(test_idr);
#define TEST5_START ((1<<27)+42) /* use the highest layer */
Fix the bug by using idr_max() which correctly takes into account the
maximum allowed shift.
sub_alloc() shares the same problem and may incorrectly fail with
-EAGAIN; however, this bug doesn't affect correct operation because
idr_get_empty_slot(), which already uses idr_max(), retries with the
increased @id in such cases.
Currently core file of aarch32 process prstatus note has empty
registers set. As result aarch32 core files create by V8 kernel are
not very useful.
It happens because compat_gpr_get and compat_gpr_set functions can
copy registers values to/from either kbuf or ubuf. ELF core file
collection function fill_thread_core_info calls compat_gpr_get
with kbuf set and ubuf set to 0. But current compat_gpr_get and
compat_gpr_set function handle copy to/from only ubuf case.
Fix is to handle kbuf and ubuf as two separate cases in similar
way as other functions like user_regset_copyout, user_regset_copyin do.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our compat PTRACE_POKEUSR implementation simply passes the user data to
regset_copy_from_user after some simple range checking. Unfortunately,
the data in question has already been copied to the kernel stack by this
point, so the subsequent access_ok check fails and the ptrace request
returns -EFAULT. This causes problems tracing fork() with older versions
of strace.
This patch briefly changes the fs to KERNEL_DS, so that the access_ok
check passes even with a kernel address.
When tracing a process in another pid namespace, it's important for fork
event messages to contain the child's pid as seen from the tracer's pid
namespace, not the parent's. Otherwise, the tracer won't be able to
correlate the fork event with later SIGTRAP signals it receives from the
child.
We still risk a race condition if a ptracer from a different pid
namespace attaches after we compute the pid_t value. However, sending a
bogus fork event message in this unlikely scenario is still a vast
improvement over the status quo where we always send bogus fork event
messages to debuggers in a different pid namespace than the forking
process.
Signed-off-by: Matthew Dempsky <mdempsky@chromium.org> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Julien Tinnes <jln@chromium.org> Cc: Roland McGrath <mcgrathr@chromium.org> Cc: Jan Kratochvil <jan.kratochvil@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kswapd exits, it can end up taking locks that were previously held
by allocating tasks while they waited for reclaim. Lockdep currently
warns about this:
On Wed, May 28, 2014 at 06:06:34PM +0800, Gu Zheng wrote:
> inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-R} usage.
> kswapd2/1151 [HC0[0]:SC0[0]:HE1:SE1] takes:
> (&sig->group_rwsem){+++++?}, at: exit_signals+0x24/0x130
> {RECLAIM_FS-ON-W} state was registered at:
> mark_held_locks+0xb9/0x140
> lockdep_trace_alloc+0x7a/0xe0
> kmem_cache_alloc_trace+0x37/0x240
> flex_array_alloc+0x99/0x1a0
> cgroup_attach_task+0x63/0x430
> attach_task_by_pid+0x210/0x280
> cgroup_procs_write+0x16/0x20
> cgroup_file_write+0x120/0x2c0
> vfs_write+0xc0/0x1f0
> SyS_write+0x4c/0xa0
> tracesys+0xdd/0xe2
> irq event stamp: 49
> hardirqs last enabled at (49): _raw_spin_unlock_irqrestore+0x36/0x70
> hardirqs last disabled at (48): _raw_spin_lock_irqsave+0x2b/0xa0
> softirqs last enabled at (0): copy_process.part.24+0x627/0x15f0
> softirqs last disabled at (0): (null)
>
> other info that might help us debug this:
> Possible unsafe locking scenario:
>
> CPU0
> ----
> lock(&sig->group_rwsem);
> <Interrupt>
> lock(&sig->group_rwsem);
>
> *** DEADLOCK ***
>
> no locks held by kswapd2/1151.
>
> stack backtrace:
> CPU: 30 PID: 1151 Comm: kswapd2 Not tainted 3.10.39+ #4
> Call Trace:
> dump_stack+0x19/0x1b
> print_usage_bug+0x1f7/0x208
> mark_lock+0x21d/0x2a0
> __lock_acquire+0x52a/0xb60
> lock_acquire+0xa2/0x140
> down_read+0x51/0xa0
> exit_signals+0x24/0x130
> do_exit+0xb5/0xa50
> kthread+0xdb/0x100
> ret_from_fork+0x7c/0xb0
This is because the kswapd thread is still marked as a reclaimer at the
time of exit. But because it is exiting, nobody is actually waiting on
it to make reclaim progress anymore, and it's nothing but a regular
thread at this point. Be tidy and strip it of all its powers
(PF_MEMALLOC, PF_SWAPWRITE, PF_KSWAPD, and the lockdep reclaim state)
before returning from the thread function.
Some drivers use the first HID report in the list instead of using an
index. In these cases, validation uses ID 0, which was supposed to mean
"first known report". This fixes the problem, which was causing at least
the lgff family of devices to stop working since hid_validate_values
was being called with ID 0, but the devices used single numbered IDs
for their reports:
Right, since conversion to mutex then rwsem, we should not put_anon_vma()
from inside an rcu_read_lock()ed section: fix the two places that did so.
And add might_sleep() to anon_vma_free(), as suggested by Peter Zijlstra.
Fixes: 88c22088bf23 ("mm: optimize page_lock_anon_vma() fast-path") Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to skip the physical block(PAGE_SIZE) which is partially covered
by the discard bio, so we check the remaining size and subtract it if
there is a need to goto the next physical block.
The current offset usage in zram_bio_discard is incorrect, it will cause
its upper filesystem breakdown. Consider the following scenario:
On some architecture or config, PAGE_SIZE is 64K for example, filesystem
is set up on zram disk without PAGE_SIZE aligned, a discard bio leads to a
offset = 4K and size=72K, normally, it should not really discard any
physical block as it partially cover two physical blocks. However, with
the current offset usage, it will discard the second physical block and
free its memory, which will cause filesystem breakdown.
This patch corrects the offset usage in zram_bio_discard.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Bob Liu <bob.liu@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently memory error handler handles action optional errors in the
deferred manner by default. And if a recovery aware application wants
to handle it immediately, it can do it by setting PF_MCE_EARLY flag.
However, such signal can be sent only to the main thread, so it's
problematic if the application wants to have a dedicated thread to
handler such signals.
So this patch adds dedicated thread support to memory error handler. We
have PF_MCE_EARLY flags for each thread separately, so with this patch
AO signal is sent to the thread with PF_MCE_EARLY flag set, not the main
thread. If you want to implement a dedicated thread, you call prctl()
to set PF_MCE_EARLY on the thread.
Memory error handler collects processes to be killed, so this patch lets
it check PF_MCE_EARLY flag on each thread in the collecting routines.
No behavioral change for all non-early kill cases.
Tony said:
: The old behavior was crazy - someone with a multithreaded process might
: well expect that if they call prctl(PF_MCE_EARLY) in just one thread, then
: that thread would see the SIGBUS with si_code = BUS_MCEERR_A0 - even if
: that thread wasn't the main thread for the process.
When Linux sees an "action optional" machine check (where h/w has reported
an error that is not in the current execution path) we generally do not
want to signal a process, since most processes do not have a SIGBUS
handler - we'd just prematurely terminate the process for a problem that
they might never actually see.
task_early_kill() decides whether to consider a process - and it checks
whether this specific process has been marked for early signals with
"prctl", or if the system administrator has requested early signals for
all processes using /proc/sys/vm/memory_failure_early_kill.
But for MF_ACTION_REQUIRED case we must not defer. The error is in the
execution path of the current thread so we must send the SIGBUS
immediatley.
Fix by passing a flag argument through collect_procs*() to
task_early_kill() so it knows whether we can defer or must take action.
When a thread in a multi-threaded application hits a machine check because
of an uncorrectable error in memory - we want to send the SIGBUS with
si.si_code = BUS_MCEERR_AR to that thread. Currently we fail to do that
if the active thread is not the primary thread in the process.
collect_procs() just finds primary threads and this test:
if ((flags & MF_ACTION_REQUIRED) && t == current) {
will see that the thread we found isn't the current thread and so send a
si.si_code = BUS_MCEERR_AO to the primary (and nothing to the active
thread at this time).
We can fix this by checking whether "current" shares the same mm with the
process that collect_procs() said owned the page. If so, we send the
SIGBUS to current (with code BUS_MCEERR_AR).
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reported-by: Otto Bruggeman <otto.g.bruggeman@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Borislav Petkov <bp@suse.de> Cc: Chen Gong <gong.chen@linux.jf.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test_bit operations in get/set pageblock flags are expensive. This
patch reads the bitmap on a word basis and use shifts and masks to isolate
the bits of interest. Similarly masks are used to set a local copy of the
bitmap and then use cmpxchg to update the bitmap if there have been no
other changes made in parallel.
In a test running dd onto tmpfs the overhead of the pageblock-related
functions went from 1.27% in profiles to 0.5%.
In addition to the performance benefits, this patch closes races that are
possible between:
a) get_ and set_pageblock_migratetype(), where get_pageblock_migratetype()
reads part of the bits before and other part of the bits after
set_pageblock_migratetype() has updated them.
b) set_pageblock_migratetype() and set_pageblock_skip(), where the non-atomic
read-modify-update set bit operation in set_pageblock_skip() will cause
lost updates to some bits changed in the set_pageblock_migratetype().
Joonsoo Kim first reported the case a) via code inspection. Vlastimil
Babka's testing with a debug patch showed that either a) or b) occurs
roughly once per mmtests' stress-highalloc benchmark (although not
necessarily in the same pageblock). Furthermore during development of
unrelated compaction patches, it was observed that frequent calls to
{start,undo}_isolate_page_range() the race occurs several thousands of
times and has resulted in NULL pointer dereferences in move_freepages()
and free_one_page() in places where free_list[migratetype] is
manipulated by e.g. list_move(). Further debugging confirmed that
migratetype had invalid value of 6, causing out of bounds access to the
free_list array.
That confirmed that the race exist, although it may be extremely rare,
and currently only fatal where page isolation is performed due to
memory hot remove. Races on pageblocks being updated by
set_pageblock_migratetype(), where both old and new migratetype are
lower MIGRATE_RESERVE, currently cannot result in an invalid value
being observed, although theoretically they may still lead to
unexpected creation or destruction of MIGRATE_RESERVE pageblocks.
Furthermore, things could get suddenly worse when memory isolation is
used more, or when new migratetypes are added.
After this patch, the race has no longer been observed in testing.
Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Jan Kara <jack@suse.cz> Cc: Michal Hocko <mhocko@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric has reported that he can see task(s) stuck in memcg OOM handler
regularly. The only way out is to
echo 0 > $GROUP/memory.oom_control
His usecase is:
- Setup a hierarchy with memory and the freezer (disable kernel oom and
have a process watch for oom).
- In that memory cgroup add a process with one thread per cpu.
- In one thread slowly allocate once per second I think it is 16M of ram
and mlock and dirty it (just to force the pages into ram and stay
there).
- When oom is achieved loop:
* attempt to freeze all of the tasks.
* if frozen send every task SIGKILL, unfreeze, remove the directory in
cgroupfs.
Eric has then pinpointed the issue to be memcg specific.
All tasks are sitting on the memcg_oom_waitq when memcg oom is disabled.
Those that have received fatal signal will bypass the charge and should
continue on their way out. The tricky part is that the exit path might
trigger a page fault (e.g. exit_robust_list), thus the memcg charge,
while its memcg is still under OOM because nobody has released any charges
yet.
Unlike with the in-kernel OOM handler the exiting task doesn't get
TIF_MEMDIE set so it doesn't shortcut further charges of the killed task
and falls to the memcg OOM again without any way out of it as there are no
fatal signals pending anymore.
This patch fixes the issue by checking PF_EXITING early in
mem_cgroup_try_charge and bypass the charge same as if it had fatal
signal pending or TIF_MEMDIE set.
Normally exiting tasks (aka not killed) will bypass the charge now but
this should be OK as the task is leaving and will release memory and
increasing the memory pressure just to release it in a moment seems
dubious wasting of cycles. Besides that charges after exit_signals should
be rare.
I am bringing this patch again (rebased on the current mmotm tree). I
hope we can move forward finally. If there is still an opposition then
I would really appreciate a concurrent approach so that we can discuss
alternatives.
http://comments.gmane.org/gmane.linux.kernel.stable/77650 is a reference
to the followup discussion when the patch has been dropped from the mmotm
last time.
Reported-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
throttle_direct_reclaim() is meant to trigger during swap-over-network
during which the min watermark is treated as a pfmemalloc reserve. It
throttes on the first node in the zonelist but this is flawed.
The user-visible impact is that a process running on CPU whose local
memory node has no ZONE_NORMAL will stall for prolonged periods of time,
possibly indefintely. This is due to throttle_direct_reclaim thinking the
pfmemalloc reserves are depleted when in fact they don't exist on that
node.
On a NUMA machine running a 32-bit kernel (I know) allocation requests
from CPUs on node 1 would detect no pfmemalloc reserves and the process
gets throttled. This patch adjusts throttling of direct reclaim to
throttle based on the first node in the zonelist that has a usable
ZONE_NORMAL or lower zone.
Commit 786235eeba0e ("kthread: make kthread_create() killable") meant
for allowing kthread_create() to abort as soon as killed by the
OOM-killer. But returning -ENOMEM is wrong if killed by SIGKILL from
userspace. Change kthread_create() to return -EINTR upon SIGKILL.
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reported-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Hugh Dickins <hughd@google.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently added page-cache dumping is known to be a little bit racy.
But after race with truncate it just dies due to unhandled SIGBUS
when it tries to poke pages beyond the new end of file.
This patch adds handler for SIGBUS which skips the rest of the file.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leandro Liptak reports that his HASEE E200 computer hangs when we ask
the BIOS to hand over control of the EHCI host controller. This
definitely sounds like a bug in the BIOS, but at the moment there is
no way to fix it.
This patch works around the problem by avoiding the handoff whenever
the motherboard and BIOS version match those of Leandro's computer.
Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
apparently required that checks for CONFIG_USB_GADGET_OMAP would be
replaced with checks for CONFIG_USB_OMAP. Do so now for the remaining
checks for CONFIG_USB_GADGET_OMAP, even though these checks have
basically been broken since v3.1.
And, since we're touching this code, use the IS_ENABLED() macro, so
things will now (hopefully) also work if USB_OMAP is modular.
Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
so it seems like DWC3 IP doesn't clear stalls
automatically when we disable an endpoint, because
of that, we _must_ make sure stalls are cleared
before clearing the proper bit in DALEPENA register.
Reported-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
basically renamed the Kconfig symbol USB_GADGET_PXA25X to USB_PXA25X. It
did not rename the related macros in use at that time. Commit c0a39151a405 ("ARM: pxa: fix inconsistent CONFIG_USB_PXA27X") did so for
all but one macro. Rename that last macro too now.
Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usbtest, tests 5 - 8 use the scatter-gather library in usbcore
without any sort of timeout. If there's a problem in the gadget or
host controller being tested, the test can hang.
This patch adds a 10-second timeout to the tests, so that they will
fail gracefully with an ETIMEDOUT error instead of hanging.
TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected. Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.
[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000a9eaf00000000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 000000000000000000000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000a9eaf00000000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0
The ->SupportedRates[] array has NDIS_802_11_LENGTH_RATES_EX (16)
elements. Since "ie_len" comes from then network and can go up to 255
then it means we should add a range check to prevent memory corruption.
Fixes: d6846af679e0 ('staging: r8188eu: Add files for new driver - part 7') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d0f47ff17f29 ("ASoC: OMAP: Build config cleanup for McBSP")
removed the Kconfig symbol OMAP_MCBSP. It left two checks for
CONFIG_OMAP_MCBSP untouched.
Convert these to checks for CONFIG_SND_OMAP_SOC_MCBSP. That must be
correct, since that re-enables calls to functions that are all found in
sound/soc/omap/mcbsp.c. And that file is built only if
CONFIG_SND_OMAP_SOC_MCBSP is defined.
Fixes: d0f47ff17f29 ("ASoC: OMAP: Build config cleanup for McBSP") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5f5c9ae56c38942623f69c3e6dc6ec78e4da2076
"serial_core: Unregister console in uart_remove_one_port()"
fixed a crash where a serial port was removed but
not deregistered as a console.
There is a side effect of that commit for platforms having serial consoles
and of_serial configured (CONFIG_SERIAL_OF_PLATFORM). The serial console
is disabled midway through the boot process.
This cessation of the serial console affects PowerPC computers
such as the MVME5100 and SAM440EP.
The sequence is:
bootconsole [udbg0] enabled
....
serial8250/16550 driver initialises and registers its UARTS,
one of these is the serial console.
console [ttyS0] enabled
....
of_serial probes "platform" devices, registering them as it goes.
One of these is the serial console.
console [ttyS0] disabled.
The disabling of the serial console is due to:
a. unregister_console in printk not clearing the
CONS_ENABLED bit in the console flags,
even though it has announced that the console is disabled; and
b. of_platform_serial_probe in of_serial not setting the port type
before it registers with serial8250_register_8250_port.
This patch ensures that the serial console is re-enabled when of_serial
registers a serial port that corresponds to the designated console.
===
The above failure was identified in Linux-3.15-rc2.
Tested using MVME5100 and SAM440EP PowerPC computers with
kernels built from Linux-3.15-rc5 and tty-next.
The continued operation of the serial console is vital for computers
such as the MVME5100 as that Single Board Computer does not
have any grapical/display hardware.
Signed-off-by: Stephen Chivers <schivers@csc.com> Tested-by: Stephen Chivers <schivers@csc.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [unregister_console] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
