The adf4378 provides only one output channel. Therefore there is only
one gpio available to enable the output. Reflect that into the bindings
using property conditions.
dt-bindings: iio: light: stk33xx: add compatible for stk3013
STK3013 is a proximity sensor by Sensortek, bearing chipid of 0x31. Despite
being marketed as a proximity sensor, it also appears to have ambient
light sensing capabilities.
The part is fully compatible with the existing implementation of the
device driver. Add the compatible string of stk3013 to the existing
list, with a fallback of stk3310.
Add support for Sensortek's STK3013 in the driver. The part bears the
product ID 0x31.
As seen in [1], Sensortek lists STK3013 as a proximity sensor. But it
has been experimentally observed that they do have ambient light sensing
capabilities. Furthermore, [2] implements a proximity and ambient light
sensor driver for STK3x1x devices, which is also indicative of the fact
that these parts are also ambient light sensors.
In order to allow newer devices which are compatible with existing
sensors, issuing a warning for an unknown chipid indicates that
something has gone wrong with the init process, which isn't ideal.
Swap it with a friendlier info message to get things right.
Petar Stoykov [Thu, 25 Jul 2024 15:37:27 +0000 (17:37 +0200)]
dt-bindings: iio: pressure: Add Sensirion SDP500
Sensirion SDP500 is a digital differential pressure sensor. It provides
a digital I2C output. Add devicetree bindings requiring the compatible
string and I2C slave address (reg).
Add support for Microchip PAC1921 Power/Current monitor.
Implemented features:
* capture of bus voltage, sense voltage, current and power measurements
in free-run integration mode
* support for both raw and triggered buffer reading
* support for overflow events
* scale attributes to control voltage and current gains
* oversampling ratio attribute to control the number of integration
samples
* sampling rate attribute that reflects the integration period
* userspace attribute and DT parameter to control shunt resistor
* simple power management support
Limitations:
* operation mode fixed to free-run integration
* READ/INT pin and OUT pin not supported
* no controls for measurement resolutions and filters
David Lechner [Tue, 23 Jul 2024 18:59:50 +0000 (13:59 -0500)]
iio: adc: mcp3564: use devm_regulator_get_enable_read_voltage()
This makes use of the new devm_regulator_get_enable_read_voltage()
helper function to reduce boilerplate code in the MCP3564 ADC driver.
The error message is slightly changed since there are fewer error
return paths.
Setting adc->vref_mv is consolidated into a single place to make the
logic easier to follow.
A use_internal_vref_attr local variable is added to make it more
obvious what the difference between the two iio info structures is.
The return value of the "Unknown Vref" dev_err_probe() is hard-coded to
-ENODEV instead of ret since it was getting a bit far from where ret
was set and logically that is the only value it could have.
Nuno Sa [Fri, 26 Jul 2024 08:23:15 +0000 (10:23 +0200)]
iio: core: annotate masklength as __private
Now that all users are using the proper accessors, we can mark
masklength as __private so that no one tries to write. We also get help
from checkers in warning us in case someone does it.
To access the private field from IIO core code, we need to use the
ACCESS_PRIVATE() macro.
Nuno Sa [Fri, 26 Jul 2024 08:23:13 +0000 (10:23 +0200)]
iio: common: cros_ec_sensors_core: use new '.masklength' accessors
Make use of iio_get_masklength) and iio_for_each_active_channel() to
access '.masklength' so it can be annotated as __private when there
are no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:12 +0000 (10:23 +0200)]
iio: adc: xilinx-xadc-core: use new '.masklength' accessors
Make use of iio_get_masklength) and iio_for_each_active_channel() to
access '.masklength' so it can be annotated as __private when there
are no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:10 +0000 (10:23 +0200)]
iio: adc: ti-ads8688: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:09 +0000 (10:23 +0200)]
iio: adc: ti-ads131e08: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:08 +0000 (10:23 +0200)]
iio: adc: ti-ads124s08: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:07 +0000 (10:23 +0200)]
iio: adc: ti-adc12138: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:06 +0000 (10:23 +0200)]
iio: adc: ti-ads1298: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:03 +0000 (10:23 +0200)]
iio: adc: ti-adc084s021: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:23:02 +0000 (10:23 +0200)]
iio: adc: ti-adc0832: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:22:59 +0000 (10:22 +0200)]
iio: adc: rtq6056: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:22:58 +0000 (10:22 +0200)]
iio: adc: rockchip_saradc: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:22:57 +0000 (10:22 +0200)]
iio: adc: mt6360-adc: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:22:56 +0000 (10:22 +0200)]
iio: adc: mcp3911: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:22:55 +0000 (10:22 +0200)]
iio: adc: max1118: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Fri, 26 Jul 2024 08:22:54 +0000 (10:22 +0200)]
iio: adc: max1118: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Move ABI documentation for custom shunt resistor attributes into the
generic iio documentation file. Exception for pac1934: leave it
untouched since it does not comply with common iio ABI generalization.
Add support for BH1745, which is an I2C colour sensor with red, green,
blue and clear channels. It has a programmable active low interrupt
pin. Interrupt occurs when the signal from the selected interrupt
source channel crosses set interrupt threshold high or low level.
Interrupt source for the device can be configured by enabling the
corresponding event. Interrupt latch is always enabled when setting
up interrupt.
Add myself as the maintainer for this driver in MAINTAINERS.
Signed-off-by: Mudit Sharma <muditsharma.info@gmail.com> Reviewed-by: Ivan Orlov <ivan.orlov0322@gmail.com> Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://patch.msgid.link/20240718220208.331942-2-muditsharma.info@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nuno Sa [Thu, 18 Jul 2024 13:38:08 +0000 (15:38 +0200)]
iio: proximity: sx_common: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:38:07 +0000 (15:38 +0200)]
iio: proximity: sx9500: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:38:06 +0000 (15:38 +0200)]
iio: proximity: hx9023s: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:38:05 +0000 (15:38 +0200)]
iio: pressure: dlhl60d: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:38:03 +0000 (15:38 +0200)]
iio: light: tcs3472: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:38:02 +0000 (15:38 +0200)]
iio: light: tcs3414: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:38:01 +0000 (15:38 +0200)]
iio: light: si1145: use new '.masklength' accessors
Make use of iio_get_masklength) and iio_for_each_active_channel() to
access '.masklength' so it can be annotated as __private when there
are no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:38:00 +0000 (15:38 +0200)]
iio: light: isl29125: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:59 +0000 (15:37 +0200)]
iio: light: gp2ap020a00f: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:58 +0000 (15:37 +0200)]
iio: light: adjd_s311: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:57 +0000 (15:37 +0200)]
iio: imu: kmx61: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:55 +0000 (15:37 +0200)]
iio: imu: bmi160_core: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:54 +0000 (15:37 +0200)]
iio: humidity: am2315: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:53 +0000 (15:37 +0200)]
iio: health: afe4404: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:51 +0000 (15:37 +0200)]
iio: health: afe4403: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:50 +0000 (15:37 +0200)]
iio: dummy: iio_simple_dummy_buffer: use iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:49 +0000 (15:37 +0200)]
iio: adc: hx711: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:48 +0000 (15:37 +0200)]
iio: adc: dln2-adc: use new '.masklength' accessors
Make use of iio_get_masklength) and iio_for_each_active_channel() to
access '.masklength' so it can be annotated as __private when there
are no more direct users of it.
Nuno Sa [Thu, 18 Jul 2024 13:37:47 +0000 (15:37 +0200)]
iio: adc: cc10001_adc: make use of iio_for_each_active_channel()
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Internal clock of AD719X devices can be made available on MCLK2 pin. Add
clock provider to support this functionality when clock cells property
is present.
Internal clock of AD719X devices can be made available on MCLK2 pin. Add
clock provider to support this functionality when clock cells property
is present.
The clock source can be either provided externally or the internal clock
is used. Pair of clocks and clock-names property is mutally exclusive
with #clock-cells property.
Modify second example to showcase the mode where internal clock is used.
There are actually 4 configuration modes of clock source for AD719X
devices. Either a crystal can be attached externally between MCLK1 and
MCLK2 pins, or an external CMOS-compatible clock can drive the MCLK2
pin. The other 2 modes make use of the 4.92MHz internal clock.
Undocumented properties adi,int-clock-output-enable and adi,clock-xtal
still supported for backward compatibility, but their use is highly
discouraged. Use cleaner alternative of configuring external clock by
using clock names mclk and xtal.
Functionality of AD7192_CLK_INT_CO will be implemented in complementary
patch by adding clock provider.
There are actually 4 configuration modes of clock source for AD719X
devices. Either a crystal can be attached externally between MCLK1 and
MCLK2 pins, or an external CMOS-compatible clock can drive the MCLK2
pin. The other 2 modes make use of the 4.92MHz internal clock.
To configure external clock as either a crystal or a CMOS-compatible
clock, changing the register settings is necessary. Therefore, add clock
name xtal alongside mclk. By selecting one or the other, the register is
configured.
The presence of an external clock source is optional, not required. When
both clocks and clock-names properties are present, an external clock
source is used. If the intention is to use the internal clock, both
properties should be absent. Modify required properties accordingly.
Marek Vasut [Mon, 15 Jul 2024 18:28:59 +0000 (20:28 +0200)]
iio: light: noa1305: Make integration time configurable
Add another attribute which is the integration time. Report available
integration time settings, support read of integration time currently
configured in hardware, and support configuration of integration time
into hardware.
Marek Vasut [Mon, 15 Jul 2024 18:28:57 +0000 (20:28 +0200)]
iio: light: noa1305: Use static table lookup of scale values
Move scale values into a static table, perform look up of those
scale values in noa1305_scale() simply by using the integration
time register content as an index, because the integration time
register content directly maps to the table values.
Marek Vasut [Mon, 15 Jul 2024 18:28:56 +0000 (20:28 +0200)]
iio: light: noa1305: Assign val in noa1305_measure()
Make noa1305_measure() behave similar to noa1305_scale(), make it
assign the 'val' output variable on success and return IIO_VAL_INT.
This further simplifies noa1305_read_raw() and allows removal of
ret variable altogether.
Marek Vasut [Mon, 15 Jul 2024 18:28:55 +0000 (20:28 +0200)]
iio: light: noa1305: Simplify noa1305_read_raw()
The only channel this hardware supports is IIO_LIGHT, if the channel
is anything else, exit right away. The 'ret' variable is now always
only assigned by noa1305_measure(), do not initialize it anymore.
Update function parameter indent. No functional change.
David Lechner [Fri, 12 Jul 2024 16:03:55 +0000 (11:03 -0500)]
iio: dac: mcp4922: drop remove() callback
By using devm_iio_device_register(), we can drop the remove() callback
in the mcp4922 driver. We can also remove spi_set_drvdata() since there
are no more callers of spi_get_drvdata(). Also use dev_err_probe()
while we are at it.
iio: pressure: bmp280: Fix waiting time for BMP3xx configuration
According to the datasheet, both pressure and temperature can go up to
oversampling x32. With this option, the maximum measurement time is not
80ms (this is for press x32 and temp x2), but it is 130ms nominal
(calculated from table 3.9.2) and since most of the maximum values
are around +15%, it is configured to 150ms.
Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family") Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com> Link: https://patch.msgid.link/20240711211558.106327-3-vassilisamir@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
David Lechner [Thu, 11 Jul 2024 19:15:42 +0000 (14:15 -0500)]
iio: adc: ad4695: Add driver for AD4695 and similar ADCs
This is a new driver for Analog Devices Inc. AD4695 and similar ADCs.
The initial driver supports initializing the chip including configuring
all possible LDO and reference voltage sources as well as any possible
voltage input channel wiring configuration.
Only the 4-wire SPI wiring mode where the CNV pin is tied to the CS pin
is supported at this time. And reading sample data from the ADC can only
be done in direct mode for now.
Co-developed-by: Ramona Gradinariu <ramona.gradinariu@analog.com> Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com> Signed-off-by: David Lechner <dlechner@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://patch.msgid.link/20240711-iio-adc-ad4695-v4-2-c31621113b57@baylibre.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduces a more generalized ABI documentation for DAC. Instead of
having separate ABI files for each DAC, we now have a single ABI file
that covers the common sysfs interface for all DAC.
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
https://patch.msgid.link/20240718051834.32270-2-kimseer.paller@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nuno Sa [Tue, 9 Jul 2024 11:14:29 +0000 (13:14 +0200)]
iio: backend: print message in case op is not implemented
For APIs that have a return value, -EOPNOTSUPP is returned in case the
backend does not support the functionality. However, for APIs that do
not have a return value we are left in silence. Hence, at least print a
debug message in case the callback is not implemented by the backend.
Add documentation for adxl380 driver which describes the driver
device files and shows how the user may use the ABI for various
scenarios (configuration, measurement, etc.).
The ADXL380/ADXL382 is a low noise density, low power, 3-axis
accelerometer with selectable measurement ranges. The ADXL380 supports
the +/-4 g, +/-8 g, and +/-16 g ranges, and the ADXL382 supports
+/-15 g, +/-30 g and +/-60 g ranges.
The ADXL380/ADXL382 offers industry leading noise, enabling precision
applications with minimal calibration. The low noise, and low power
ADXL380/ADXL382 enables accurate measurement in an environment with
high vibration, heart sounds and audio.
In addition to its low power consumption, the ADXL380/ADXL382 has many
features to enable true system level performance. These include a
built-in micropower temperature sensor, single / double / triple tap
detection and a state machine to prevent a false triggering. In
addition, the ADXL380/ADXL382 has provisions for external control of
the sampling time and/or an external clock.
projects / thirdparty / kernel / stable.git / log
