John Crispin [Wed, 28 Jan 2015 19:19:33 +0000 (19:19 +0000)]
comgt-ncm: Fix NCM protocol
This patch fixes the NCM protocol by adding the missing ifname
to the netifd script and changing one unintended "send" statement to
"print" in runcommand.gcom. It also cleans up logging and makes the
manufacturer names case-insensitive. Furthermore, comgt-ncm should
not depend on the USB-serial-related kernel modules, as the cdc-wdm
control device works without them. There is also no need to depend on
kmod-huawei-cdc-ncm, since other manufacturers (like Sony-Ericsson
and Samsung) which use other kernel modules should also be supported.
I'd appreciate if someone with Samsung or Sony-Ericsson modems could
test this, I was only able to test it with Huawei E3276, E3372 and
E353.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44182
After r43987 TARGET_lantiq_xrx200_P2812HNUFX does not exist anymore.
Fix empty menuconfig bootloader selection by making u-boot depend on
one of the new target profiles.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44179
John Crispin [Wed, 28 Jan 2015 12:07:47 +0000 (12:07 +0000)]
cURL: Update to version 7.40.0
* Update to version 7.40.0
* remove non existing config options around enable/disable HTTPS protocoll
* remove --with-ca-path if ssl support disabled
* set proxy support as default like all versions before CC did
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 44176
John Crispin [Wed, 28 Jan 2015 12:07:29 +0000 (12:07 +0000)]
libertas: configure sysfs symlinks
Update the libertas driver to configure symlinks in sysfs. This enables
the driver to be handled correctly by the mac80211/netifd/hostapd scripts.
With this patch, the wireless interface is functional on Guruplug Server Plus.
John Crispin [Wed, 28 Jan 2015 12:07:21 +0000 (12:07 +0000)]
mac80211: Add some missing 802.11n capabilities to hostapd configuration
Add some missing 802.11n capabilities to the hostapd ht_capab string when
supported by the hardware: Spatial Multiplexing Power-Save and 7935-byte AMSDUs.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44173
John Crispin [Wed, 28 Jan 2015 12:07:08 +0000 (12:07 +0000)]
mac80211: fix fallback to macaddr
If '/sys/class/ieee80211/phyN' is not a symlink, the call to readlink
produces either an empty path (if /sys/class/ieee80211/phyN/device doesn't
exist) or a path that begins with '/sys/class/ieee80211' (which does not
work with the subsequent line to strip '/sys/devices' from the beginning of
the path). Modify the checks to detect these conditions, and fallback to
using the macaddr.
John Crispin [Wed, 28 Jan 2015 12:06:22 +0000 (12:06 +0000)]
ralink: check ethernet MAC address whether it is valid
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Jo-Philipp Wich [Sun, 25 Jan 2015 17:23:26 +0000 (17:23 +0000)]
uhttpd: fix crash with enabled relro, memory leak in dirlists and lfs
* Fix the ubus plugin to not make its uhttpd_plugin entry symbol
constant as uhttpd needs to modify its list_head member
* Make sure that uhttpd supports large files by using 64bit ints
where appropriate and by passing _FILE_OFFSET_BITS=64 to the build
* Plug a possible memleak in the directory listing code
Jo-Philipp Wich [Sun, 25 Jan 2015 15:55:03 +0000 (15:55 +0000)]
xburst: fix kernel build
Changeset r43049 removed the "062-mips_decompressor_build_fix.patch" which is
still required to properly build the xburst kernel.
Fix the syntax error in the preprocessed code by explicitely undefining the
"memcpy" and "memset" macros prior to declaring the replacements functions.
Luka Perkov [Sun, 25 Jan 2015 13:11:02 +0000 (13:11 +0000)]
kirkwood: drop port-based VLAN setup
Using port-based VLANs depends on a non-standard
swconfig parameter, which compilcates things like
LuCI that don't know about it. This patch changes
the default to use 802.1q VLANs internally in the
switch, but without tagging packets since we have
two Ethernet ports.
iperf3 tests indicate no difference in performance
versus port-based VLANs when the CPU port is not
using tags.
Felix Fietkau [Sat, 24 Jan 2015 22:45:28 +0000 (22:45 +0000)]
ralink: fix ethernet feature TSO not work
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
Felix Fietkau [Sat, 24 Jan 2015 19:42:06 +0000 (19:42 +0000)]
ar8216: add swconfig attribute to display ARL table on AR8327/AR8337
Add global read-only swconfig attribute "arl_table" to display the
address resolution table.
So far the chip-specific part is implemented for AR8327/AR8337 only
as I don't have the datasheets for the other AR8XXX chips.
Successfully tested on TL-WDR4300 (AR8327rev2)
and TL-WDR4900 (AR8327rev4).
Felix Fietkau [Sat, 24 Jan 2015 19:42:01 +0000 (19:42 +0000)]
ar8216: decrease page switch wait time
Until a few years ago the page switch wait time was set to msleep(1)
what was changed to usleep_range(1000, 2000) later.
I can not imagine that a low-level operation like switching page
on register level takes so much time.
Most likely the value of 1ms was initially set to check whether
it fixes an issue and then remained w/o further checking whether
also a smaller value would be sufficient.
Now the wait time is set to 5us and I successfully tested this on
AR8327. IMHO 5us should be plenty of time for all supported chips.
However I couldn't test this due to missing hardware.
If other chips should need a longer wait time we can add the
wait time as a parameter to the ar8xxx_chip struct.
Felix Fietkau [Sat, 24 Jan 2015 19:41:51 +0000 (19:41 +0000)]
ar8216: fix ATU flushing
The functionality to flush the address translation table contains two bugs
which luckily compensate each other.
1. Just setting the operation is not sufficient to perform the flushing.
The "active" bit needs to be set to actually trigger an action.
For the vtu operations this is implemented correctly.
2. ar8xxx_phy_read_status is called every 2s by the phy state machine
to check for link changes. This would have caused an ATU flush
every 2s.
Fix the chip-specific ATU flush functions and remove the ATU flush call
from ar8xxx_phy_read_status.
Jo-Philipp Wich [Sat, 24 Jan 2015 11:30:45 +0000 (11:30 +0000)]
ppp: rework host-uniq support to take hex encoded strings
The previous implementation of the "host-uniq" option used plain strings for
passing the value to pppd which made it impossible to specify binary data.
Switch the format to a hex encoded string to support binary data.
John Crispin [Fri, 23 Jan 2015 12:32:36 +0000 (12:32 +0000)]
modules: add 6LoWPAN over Bluetooth Low Energy
Adding support 6LoWPAN over Bluetooth Low Energy in kernel 3.18.
Creating new bluetooth_6lowpan group with CONFIG_6LOWPAN and CONFIG_BT_6LOWPAN.
Adding kernel object dependencies for 6LoWPAN over Bluetooth Low Energy.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no> Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44084
John Crispin [Fri, 23 Jan 2015 12:32:28 +0000 (12:32 +0000)]
lantiq: correct value for fpi clock on ar9
This adds a patch to target/linux/lantiq/patches-3.14
fixing a bug clock code on ar9. The current version returns
the wrong value for the fpi clock frequency in some
cases.
See discussion for further details:
https://lists.openwrt.org/pipermail/openwrt-devel/2015-January/030688.html
I'm not sure about the patch naming and numbering convention.
Do please let me know it this is not OK.
Many thanks,
Ben Mulvihill
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 44083
John Crispin [Thu, 22 Jan 2015 09:35:40 +0000 (09:35 +0000)]
build: allow openwrt.git packages to be replaced by feeds
Currently, replacing a package available in openwrt.git requires
modifications in openwrt.git, or requires duplicating the package in a
feed but with a different name, which causes all kind of problems
related to dependencies (all packages selecting it would have to be
modified accordingly to select the new package).
With this change, if a package with the same name is present both in
feeds/ and package/ folders, the one in feeds/ can override the one
in package/, both in the menuconfig and during the build, by passing the
"-f" option to "./scripts/feeds install"
This mechanism is particularly useful for vendor tree, or in general for
application which needs to replace one particular package which exists
within openwrt.git by a custom/newer version.
John Crispin [Thu, 22 Jan 2015 09:35:12 +0000 (09:35 +0000)]
ramips: improve and fix Memory 2 Move support
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
projects / thirdparty / openwrt.git / log
