When the RX or TX coalesce count is set to 1, there's no point in
setting the delay timer value since an interrupt will already be raised
on every packet, and the delay interrupt just causes extra pointless
interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
The following sequence of commands causes a livelock - there will be
workqueue process looping and consuming 100% CPU:
dmsetup create --notable test
truncate -s 1MiB testdata
losetup /dev/loop0 testdata
dmsetup load test --table '0 2048 linear /dev/loop0 0'
dd if=/dev/zero of=/dev/dm-0 bs=16k count=1 conv=fdatasync
The livelock is caused by the commit fa247089de99. The commit claims that
it fixes a race condition, however, it is unknown what the actual race
condition is and what program is involved in the race condition.
When the inactive table is loaded, the nodes /dev/dm-0 and
/sys/block/dm-0 are created. /dev/dm-0 has zero size at this point. When
the device is suspended and resumed, the nodes /dev/mapper/test and
/dev/disk/* are created.
If some program opens a block device before it is created by dmsetup or
lvm, the program is buggy, so dm could just report an error as it used to
do before.
We used to call irq_bypass_unregister_producer() in
vhost_vdpa_setup_vq_irq() which is problematic as we don't know if the
token pointer is still valid or not.
Actually, we use the eventfd_ctx as the token so the life cycle of the
token should be bound to the VHOST_SET_VRING_CALL instead of
vhost_vdpa_setup_vq_irq() which could be called by set_status().
Fixing this by setting up irq bypass producer's token when handling
VHOST_SET_VRING_CALL and un-registering the producer before calling
vhost_vring_ioctl() to prevent a possible use after free as eventfd
could have been released in vhost_vring_ioctl(). And such registering
and unregistering will only be done if DRIVER_OK is set.
Reported-by: Dragos Tatulea <dtatulea@nvidia.com> Tested-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Fixes: 2cf1ba9a4d15 ("vhost_vdpa: implement IRQ offloading in vhost_vdpa") Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240816031900.18013-1-jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This due to the fact that we do not free the "sg_table" itself while
freeing up the SG table and data pages. Fix this by freeing the sg_table
in tmc_free_sg_table().
Fixes: 99443ea19e8b ("coresight: Add generic TMC sg table framework") Cc: Mike Leach <mike.leach@linaro.org> Cc: James Clark <james.clark@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20240702132846.1677261-1-suzuki.poulose@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The binding's documentation specifies that "As the line is active low, it
should be marked GPIO_ACTIVE_LOW". However, in the driver, it was handled
the opposite way. This commit sets the driver's behaviour in sync with the
documentation
Fixes: 722407a4e8c0 ("staging:iio:ad7606: Use GPIO descriptor API") Signed-off-by: Guillaume Stols <gstols@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gpiod_set_array_value was misused here: the implementation relied on the
assumption that an unsigned long was required for each gpio, while the
function expects a bit array stored in "as much unsigned long as needed
for storing one bit per GPIO", i.e it is using a bit field.
This leaded to incorrect parameter passed to gpiod_set_array_value, that
would set 1 value instead of 3.
It also prevents to select the software mode correctly for the AD7606B.
Fixes: d2a415c86c6b ("iio: adc: ad7606: Add support for AD7606B ADC") Fixes: 41f71e5e7daf ("staging: iio: adc: ad7606: Use find_closest() macro") Signed-off-by: Guillaume Stols <gstols@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Link: https://patch.msgid.link/20240906021251.610462-1-ruanjinjie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The requested DMA channels are never released. Do this in .remove as well
as in .probe. spi_register_controller() can return -EPROBE_DEFER if
cs-gpios are not probed yet.
Do not print error messages with error code -517. Silences the following
errors upon on imx8qm:
fsl_lpspi 5a000000.spi: spi_register_controller error: -517
fsl_lpspi 5a010000.spi: spi_register_controller error: -517
fsl_lpspi 5a020000.spi: spi_register_controller error: -517
Online repaire on corrupted directory in f2fs_lookup() can generate
dirty data/meta while racing w/ readonly remount, it may leave dirty
inode after filesystem becomes readonly, however, checkpoint() will
skips flushing dirty inode in a state of readonly mode, result in
above panic.
Let's get rid of online repaire in f2fs_lookup(), and leave the work
to fsck.f2fs.
Once F2FS_IPU_FORCE policy is enabled in some cases:
a) f2fs forces to use F2FS_IPU_FORCE in a small-sized volume
b) user sets F2FS_IPU_FORCE policy via sysfs
Then we may fail to defragment file due to IPU policy check, it doesn't
make sense, let's introduce a new IPU policy to allow OPU during file
defragmentation.
In small-sized volume, let's enable F2FS_IPU_HONOR_OPU_WRITE policy
by default.
Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: 884ee6dc85b9 ("f2fs: get rid of online repaire on corrupted directory") Signed-off-by: Sasha Levin <sashal@kernel.org>
Soft IRQ Thread
- f2fs_write_end_io
- f2fs_defragment_range
- set_page_private_gcing
- type = WB_DATA_TYPE(page, false);
: assign type w/ F2FS_WB_CP_DATA
due to page_private_gcing() is true
- dec_page_count() w/ wrong type
- end_page_writeback()
Value of F2FS_WB_CP_DATA reference count may become negative under above
race condition, the root cause is we missed to wait page writeback before
setting gcing page private flag, let's fix it.
Fixes: 2d1fe8a86bf5 ("f2fs: fix to tag gcing flag on page during file defragment") Fixes: 4961acdd65c9 ("f2fs: fix to tag gcing flag on page during block migration") Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We may trigger high frequent checkpoint for below case:
1. mkdir /mnt/dir1; set dir1 encrypted
2. touch /mnt/file1; fsync /mnt/file1
3. mkdir /mnt/dir2; set dir2 encrypted
4. touch /mnt/file2; fsync /mnt/file2
...
Although, newly created dir and file are not related, due to
commit bbf156f7afa7 ("f2fs: fix lost xattrs of directories"), we will
trigger checkpoint whenever fsync() comes after a new encrypted dir
created.
In order to avoid such performance regression issue, let's record an
entry including directory's ino in global cache whenever we update
directory's xattr data, and then triggerring checkpoint() only if
xattr metadata of target file's parent was updated.
This patch updates to cover below no encryption case as well:
1) parent is checkpointed
2) set_xattr(dir) w/ new xnid
3) create(file)
4) fsync(file)
Fixes: bbf156f7afa7 ("f2fs: fix lost xattrs of directories") Reported-by: wangzijie <wangzijie1@honor.com> Reported-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Tested-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Reported-by: Yunlei He <heyunlei@hihonor.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
generic/728 - output mismatch (see /media/fstests/results//generic/728.out.bad)
--- tests/generic/728.out 2023-07-19 07:10:48.362711407 +0000
+++ /media/fstests/results//generic/728.out.bad 2023-07-19 08:39:57.000000000 +0000
QA output created by 728
+Expected ctime to change after setxattr.
+Expected ctime to change after removexattr.
Silence is golden
...
(Run 'diff -u /media/fstests/tests/generic/728.out /media/fstests/results//generic/728.out.bad' to see the entire diff)
generic/729 1s
It needs to update i_ctime after {set,remove}xattr, fix it.
When we have a corrupted main.sqlite in /var/lib/nfs/nfsdcld/, it may
result in namelen being 0, which will cause memdup_user() to return
ZERO_SIZE_PTR.
When we access the name.data that has been assigned the value of
ZERO_SIZE_PTR in nfs4_client_to_reclaim(), null pointer dereference is
triggered.
If not enough buffer space available, but idmap_lookup has triggered
lookup_fn which calls cache_get and returns successfully. Then we
missed to call cache_put here which pairs with cache_get.
Fixes: ddd1ea563672 ("nfsd4: use xdr_reserve_space in attribute encoding") Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev> Reviwed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The lookup_atid() function can return NULL if the ATID is
invalid or does not exist in the identifier table, which
could lead to dereferencing a null pointer without a
check in the `act_establish()` and `act_open_rpl()` functions.
Add a NULL check to prevent null pointer dereferencing.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
When allocating MTT hem, for each hop level of each hem that is being
allocated, the driver iterates the hem list to find out whether the
bt page has been allocated in this hop level. If not, allocate a new
one and splice it to the list. The time complexity is O(n^2) in worst
cases.
Currently the allocation for-loop uses 'unit' as the step size. This
actually has taken into account the reuse of last-hop-level MTT bt
pages by multiple buffer pages. Thus pages of last hop level will
never have been allocated, so there is no need to iterate the hem list
in last hop level.
Removing this unnecessary iteration can reduce the time complexity to
O(n).
Fixes: 38389eaa4db1 ("RDMA/hns: Add mtr support for mixed multihop addressing") Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://patch.msgid.link/20240906093444.3571619-9-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In abnormal interrupt handler, a PF reset will be triggered even if
the device is a VF. It should be a VF reset.
Fixes: 2b9acb9a97fe ("RDMA/hns: Add the process of AEQ overflow for hip08") Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://patch.msgid.link/20240906093444.3571619-7-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HNS NIC driver receives and handles the abnormal interrupt of the RAS
type generated by ROCEE, and the HNS RDMA driver does not need to handle
this type of interrupt. Therefore, delete unused codes in the HNS RDMA
driver.
Parts of the suspend and resume chain is left unprotected if we disable
the WDT here.
>From experiments we can see that the SCU disables and re-enables the WDT
when we enter and leave suspend to ram. By not touching the WDT here we
are protected by the WDT all the way to the SCU.
When ib_cache_update return an error, we exit ib_cache_setup_one
instantly with no proper cleanup, even though before this we had
already successfully done gid_table_setup_one, that results in
the kernel WARN below.
Do proper cleanup using gid_table_cleanup_one before returning
the err in order to fix the issue.
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
If we wait_for_construction and find that the file is no longer hashed,
and we're going to retry the open, the old nfsd_file reference is
currently leaked. Put the reference before retrying.
Fixes: c6593366c0bf ("nfsd: don't kill nfsd_files because of lease break error") Signed-off-by: Jeff Layton <jlayton@kernel.org> Tested-by: Youzhong Yang <youzhong@gmail.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fix leaking the of_node references in of_dra7_atl_clk_probe().
The docs for of_parse_phandle_with_args() say that the caller must call
of_node_put() on the returned node. This adds the missing of_node_put()
to fix the leak.
In the function init_conns(), after the create_con() and create_cm() for
loop if something fails. In the cleanup for loop after the destroy tag, we
access out of bound memory because cid is set to clt_path->s.con_num.
This commits resets the cid to clt_path->s.con_num - 1, to stay in bounds
in the cleanup loop later.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://patch.msgid.link/20240821112217.41827-7-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reset hb_missed_cnt after receiving traffic from other peer, so
hb is more robust again high load on host or network.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://patch.msgid.link/20240821112217.41827-5-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the commit aee2424246f9 ("RDMA/iwcm: Fix a use-after-free related to
destroying CM IDs"), the function flush_workqueue is invoked to flush the
work queue iwcm_wq.
But at that time, the work queue iwcm_wq was created via the function
alloc_ordered_workqueue without the flag WQ_MEM_RECLAIM.
Because the current process is trying to flush the whole iwcm_wq, if
iwcm_wq doesn't have the flag WQ_MEM_RECLAIM, verify that the current
process is not reclaiming memory or running on a workqueue which doesn't
have the flag WQ_MEM_RECLAIM as that can break forward-progress guarantee
leading to a deadlock.
Ensure index in rtl2830_pid_filter does not exceed 31 to prevent
out-of-bounds access.
dev->filters is a 32-bit value, so set_bit and clear_bit functions should
only operate on indices from 0 to 31. If index is 32, it will attempt to
access a non-existent 33rd bit, leading to out-of-bounds access.
Change the boundary check from index > 32 to index >= 32 to resolve this
issue.
Fixes: df70ddad81b4 ("[media] rtl2830: implement PID filter") Signed-off-by: Junlin Li <make24@iscas.ac.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure index in rtl2832_pid_filter does not exceed 31 to prevent
out-of-bounds access.
dev->filters is a 32-bit value, so set_bit and clear_bit functions should
only operate on indices from 0 to 31. If index is 32, it will attempt to
access a non-existent 33rd bit, leading to out-of-bounds access.
Change the boundary check from index > 32 to index >= 32 to resolve this
issue.
Signed-off-by: Junlin Li <make24@iscas.ac.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 4b01e01a81b6 ("[media] rtl2832: implement PID filter")
[hverkuil: added fixes tag, rtl2830_pid_filter -> rtl2832_pid_filter in logmsg] Signed-off-by: Sasha Levin <sashal@kernel.org>
For different reasons i2c transaction may fail or report id in the
message may be wrong. Avoid closing the frame in this case as it will
result in all contacts being dropped, indicating that nothing is
touching the screen anymore, while usually it is not the case.
Fixes: 42370681bd46 ("Input: Add support for ILITEK Lego Series") Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Link: https://lore.kernel.org/r/20240805085511.43955-2-francesco@dolcini.it Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to DCLK_LCDC on RK3328, the DCLK_VOP on RK3228 is typically
parented by the hdmiphy clk and it is expected that the DCLK_VOP and
hdmiphy clk rate are kept in sync.
Use CLK_SET_RATE_PARENT and CLK_SET_RATE_NO_REPARENT flags, same as used
on RK3328, to make full use of all possible supported display modes.
Fixes: 0a9d4ac08ebc ("clk: rockchip: set the clock ids for RK3228 VOP") Fixes: 307a2e9ac524 ("clk: rockchip: add clock controller for rk3228") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Link: https://lore.kernel.org/r/20240615170417.3134517-3-jonas@kwiboo.se Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize workqueue before requesting mailbox channel, otherwise if
mailbox interrupt comes before workqueue ready, the imx_rproc_rx_callback
will trigger issue.
The initialization order of SCU clocks affects the sequence of SCU clock
resume. If there are no other effects, the earlier the initialization,
the earlier the resume. During SCU clock resume, the clock rate is
restored. As SCFW guidelines, configure the parent clock rate before
configuring the child rate.
Fixes: babfaa9556d7 ("clk: imx: scu: add more scu clocks") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20240607133347.3291040-15-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The initialization order of SCU clocks affects the sequence of SCU clock
resume. If there are no other effects, the earlier the initialization,
the earlier the resume. During SCU clock resume, the clock rate is
restored. As SCFW guidelines, configure the parent clock rate before
configuring the child rate.
Fixes: 91e916771de0 ("clk: imx: scu: remove legacy scu clock binding support") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20240607133347.3291040-14-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the i.MX8M*, the TF-A exposes a SiP (Silicon Provider) service
for DDR frequency scaling. The imx8m-ddrc-devfreq driver calls the
SiP and then does clk_set_parent on the DDR muxes to synchronize
the clock tree.
since commit 936c383673b9 ("clk: imx: fix composite peripheral flags"),
these TF-A managed muxes have SET_PARENT_GATE set, which results
in imx8m-ddrc-devfreq's clk_set_parent after SiP failing with -EBUSY:
commit 926bf91248dd
("clk: imx8m: fix clock tree update of TF-A managed clocks") adds this
method and enables 8mm, 8mn and 8mq. i.MX8MP also needs it.
This is safe to do, because updating the Linux clock tree to reflect
reality will always be glitch-free.
Another reason to this patch is that powersave image BT music
requires dram to be 400MTS, so clk_set_parent(dram_alt_src,
sys1_pll_800m); is required. Without this patch, it will not succeed.
Fixes: 936c383673b9 ("clk: imx: fix composite peripheral flags") Signed-off-by: Zhipeng Wang <zhipeng.wang_1@nxp.com> Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20240607133347.3291040-7-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Switch strtoul to strtoull as an unsigned long in 32-bit build isn't
64-bits.
Fixes: c284d669a20d408b ("perf tools: Move parse_nsec_time to time-utils.c") Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com> Cc: Chaitanya S Prakash <chaitanyas.prakash@arm.com> Cc: Colin Ian King <colin.i.king@gmail.com> Cc: David Ahern <dsa@cumulusnetworks.com> Cc: Dominique Martinet <asmadeus@codewreck.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@linaro.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Garry <john.g.garry@oracle.com> Cc: Junhao He <hejunhao3@huawei.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Yang Jihong <yangjihong@bytedance.com> Link: https://lore.kernel.org/r/20240831070415.506194-3-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sched_in event for current task is not recorded, sched_in timestamp
will be set to end_time of time window interest, causing an error in
timestamp show. In this case, we choose to ignore this event.
Test scenario:
perf[1229608] does not record the first sched_in event, run time and sch delay are both 0
# perf sched timehist
Samples of sched_switch event do not have callchains.
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ ------------------------------ --------- --------- --------- 2090450.763231 [0000] perf[1229608] 0.000 0.000 0.000 2090450.763235 [0000] migration/0[15] 0.000 0.001 0.003 2090450.763263 [0001] perf[1229608] 0.000 0.000 0.000 2090450.763268 [0001] migration/1[21] 0.000 0.001 0.004 2090450.763302 [0002] perf[1229608] 0.000 0.000 0.000 2090450.763309 [0002] migration/2[27] 0.000 0.001 0.007 2090450.763338 [0003] perf[1229608] 0.000 0.000 0.000 2090450.763343 [0003] migration/3[33] 0.000 0.001 0.004
Before:
arbitrarily specify a time window of interest, timestamp will be set to an incorrect value
# perf sched timehist --time 100,200
Samples of sched_switch event do not have callchains.
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ ------------------------------ --------- --------- ---------
200.000000 [0000] perf[1229608] 0.000 0.000 0.000
200.000000 [0001] perf[1229608] 0.000 0.000 0.000
200.000000 [0002] perf[1229608] 0.000 0.000 0.000
200.000000 [0003] perf[1229608] 0.000 0.000 0.000
200.000000 [0004] perf[1229608] 0.000 0.000 0.000
200.000000 [0005] perf[1229608] 0.000 0.000 0.000
200.000000 [0006] perf[1229608] 0.000 0.000 0.000
200.000000 [0007] perf[1229608] 0.000 0.000 0.000
After:
# perf sched timehist --time 100,200
Samples of sched_switch event do not have callchains.
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ ------------------------------ --------- --------- ---------
Fixes: 853b74071110bed3 ("perf sched timehist: Add option to specify time window of interest") Signed-off-by: Yang Jihong <yangjihong@bytedance.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsa@cumulusnetworks.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20240819024720.2405244-1-yangjihong@bytedance.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When perf_time__parse_str() fails in perf_sched__timehist(),
need to free session that was previously created, fix it.
Fixes: 853b74071110bed3 ("perf sched timehist: Add option to specify time window of interest") Signed-off-by: Yang Jihong <yangjihong@bytedance.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsa@cumulusnetworks.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20240806023533.1316348-1-yangjihong@bytedance.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bpf_strtol() and bpf_strtoul() helpers are currently broken on 32bit:
The argument type ARG_PTR_TO_LONG is BPF-side "long", not kernel-side "long"
and therefore always considered fixed 64bit no matter if 64 or 32bit underlying
architecture.
This contract breaks in case of the two mentioned helpers since their BPF_CALL
definition for the helpers was added with {unsigned,}long *res. Meaning, the
transition from BPF-side "long" (BPF program) to kernel-side "long" (BPF helper)
breaks here.
Both helpers call __bpf_strtoll() with "long long" correctly, but later assigning
the result into 32-bit "*(long *)" on 32bit architectures. From a BPF program
point of view, this means upper bits will be seen as uninitialised.
Therefore, fix both BPF_CALL signatures to {s,u}64 types to fix this situation.
Now, changing also uapi/bpf.h helper documentation which generates bpf_helper_defs.h
for BPF programs is tricky: Changing signatures there to __{s,u}64 would trigger
compiler warnings (incompatible pointer types passing 'long *' to parameter of type
'__s64 *' (aka 'long long *')) for existing BPF programs.
Leaving the signatures as-is would be fine as from BPF program point of view it is
still BPF-side "long" and thus equivalent to __{s,u}64 on 64 or 32bit underlying
architectures.
Note that bpf_strtol() and bpf_strtoul() are the only helpers with this issue.
The function nilfs_btree_check_delete(), which checks whether degeneration
to direct mapping occurs before deleting a b-tree entry, causes memory
access outside the block buffer when retrieving the maximum key if the
root node has no entries.
This does not usually happen because b-tree mappings with 0 child nodes
are never created by mkfs.nilfs2 or nilfs2 itself. However, it can happen
if the b-tree root node read from a device is configured that way, so fix
this potential issue by adding a check for that case.
Due to the nature of b-trees, nilfs2 itself and admin tools such as
mkfs.nilfs2 will never create an intermediate b-tree node block with 0
child nodes, nor will they delete (key, pointer)-entries that would result
in such a state. However, it is possible that a b-tree node block is
corrupted on the backing device and is read with 0 child nodes.
Because operation is not guaranteed if the number of child nodes is 0 for
intermediate node blocks other than the root node, modify
nilfs_btree_node_broken(), which performs sanity checks when reading a
b-tree node block, so that such cases will be judged as metadata
corruption.
Patch series "nilfs2: fix potential issues with empty b-tree nodes".
This series addresses three potential issues with empty b-tree nodes that
can occur with corrupted filesystem images, including one recently
discovered by syzbot.
This patch (of 3):
If a b-tree is broken on the device, and the b-tree height is greater than
2 (the level of the root node is greater than 1) even if the number of
child nodes of the b-tree root is 0, a NULL pointer dereference occurs in
nilfs_btree_prepare_insert(), which is called from nilfs_btree_insert().
This is because, when the number of child nodes of the b-tree root is 0,
nilfs_btree_do_lookup() does not set the block buffer head in any of
path[x].bp_bh, leaving it as the initial value of NULL, but if the level
of the b-tree root node is greater than 1, nilfs_btree_get_nonroot_node(),
which accesses the buffer memory of path[x].bp_bh, is called.
Fix this issue by adding a check to nilfs_btree_root_broken(), which
performs sanity checks when reading the root node from the device, to
detect this inconsistency.
Thanks to Lizhi Xu for trying to solve the bug and clarifying the cause
early on.
When looking up for an entry in an inlined directory, if e_value_offs is
changed underneath the filesystem by some change in the block device, it
will lead to an out-of-bounds access that KASAN detects as an UAF.
EXT4-fs (loop0): mounted filesystem 00000000-0000-0000-0000-000000000000 r/w without journal. Quota mode: none.
loop0: detected capacity change from 2048 to 2047
==================================================================
BUG: KASAN: use-after-free in ext4_search_dir+0xf2/0x1c0 fs/ext4/namei.c:1500
Read of size 1 at addr ffff88803e91130f by task syz-executor269/5103
Calling ext4_xattr_ibody_find right after reading the inode with
ext4_get_inode_loc will lead to a check of the validity of the xattrs,
avoiding this problem.
Reported-by: syzbot+0c2508114d912a54ee79@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=0c2508114d912a54ee79 Fixes: e8e948e7802a ("ext4: let ext4_find_entry handle inline data") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Link: https://patch.msgid.link/20240821152324.3621860-5-cascardo@igalia.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of errors when reading an inode from disk or traversing inline
directory entries, return an error-encoded ERR_PTR instead of returning
NULL. ext4_find_inline_entry only caller, __ext4_find_entry already returns
such encoded errors.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Link: https://patch.msgid.link/20240821152324.3621860-3-cascardo@igalia.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: c6b72f5d82b1 ("ext4: avoid OOB when system.data xattr changes underneath the filesystem") Signed-off-by: Sasha Levin <sashal@kernel.org>
min_clusters is signed integer and will be converted to unsigned
integer when compared with unsigned number stats.free_clusters.
If min_clusters is negative, it will be converted to a huge unsigned
value in which case all groups may not meet the actual desired free
clusters.
Set negative min_clusters to 0 to avoid unexpected behavior.
If a group is marked EXT4_GROUP_INFO_IBITMAP_CORRUPT after it's inode
bitmap buffer_head was successfully verified, then __ext4_new_inode()
will get a valid inode_bitmap_bh of a corrupted group from
ext4_read_inode_bitmap() in which case inode_bitmap_bh misses a release.
Hnadle "IS_ERR(inode_bitmap_bh)" and group corruption separately like
how ext4_free_inode() does to avoid buffer_head leak.
Fixes: 9008a58e5dce ("ext4: make the bitmap read routines return real error codes") Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com> Link: https://patch.msgid.link/20240820132234.2759926-3-shikemeng@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Release inode_bitmap_bh from ext4_read_inode_bitmap() in
ext4_mark_inode_used() to avoid buffer_head leak.
By the way, remove unneeded goto for invalid ino when inode_bitmap_bh
is NULL.
In the `smk_set_cipso` function, the `skp->smk_netlabel.attr.mls.cat`
field is directly assigned to a new value without using the appropriate
RCU pointer assignment functions. According to RCU usage rules, this is
illegal and can lead to unpredictable behavior, including data
inconsistencies and impossible-to-diagnose memory corruption issues.
This possible bug was identified using a static analysis tool developed
by myself, specifically designed to detect RCU-related issues.
To address this, the assignment is now done using rcu_assign_pointer(),
which ensures that the pointer assignment is done safely, with the
necessary memory barriers and synchronization. This change prevents
potential RCU dereference issues by ensuring that the `cat` field is
safely updated while still adhering to RCU's requirements.
Fixes: 0817534ff9ea ("smackfs: Fix use-after-free in netlbl_catmap_walk()") Signed-off-by: Jiawei Ye <jiawei.ye@foxmail.com> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3d56b8d2c74c ("ext4: Speed up FITRIM by recording flags in
ext4_group_info") speed up fstrim by skipping trim trimmed group. We
also has the chance to clear trimmed once there exists some block free
for this group(mount without discard), and the next trim for this group
will work well too.
For mount with discard, we will issue dicard when we free blocks, so
leave trimmed flag keep alive to skip useless trim trigger from
userspace seems reasonable. But for some case like ext4 build on
dm-thinpool(ext4 blocksize 4K, pool blocksize 128K), discard from ext4
maybe unaligned for dm thinpool, and thinpool will just finish this
discard(see process_discard_bio when begein equals to end) without
actually process discard. For this case, trim from userspace can really
help us to free some thinpool block.
So convert to clear trimmed flag for all case no matter mounted with
discard or not.
Fixes: 3d56b8d2c74c ("ext4: Speed up FITRIM by recording flags in ext4_group_info") Signed-off-by: yangerkun <yangerkun@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://patch.msgid.link/20240817085510.2084444-1-yangerkun@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
When analyzing a kernel waring message, Peter pointed out that there is a
race condition when the kworker is being frozen and falls into
try_to_freeze() with TASK_INTERRUPTIBLE, which could trigger a
might_sleep() warning in try_to_freeze(). Although the root cause is not
related to freeze()[1], it is still worthy to fix this issue ahead.
In 2018, a dependency on <linux/crc32poly.h> was added to avoid
duplicating the same constant in multiple files. Two months later it was
found to be a bad idea and the definition of CRC32_POLY_LE macro was moved
into xz_private.h to avoid including <linux/crc32poly.h>.
xz_private.h is a wrong place for it too. Revert back to the upstream
version which has the poly in xz_crc32_init() in xz_crc32.c.
Link: https://lkml.kernel.org/r/20240721133633.47721-10-lasse.collin@tukaani.org Fixes: faa16bc404d7 ("lib: Use existing define with polynomial") Fixes: 242cdad873a7 ("lib/xz: Put CRC32_POLY_LE in xz_private.h") Signed-off-by: Lasse Collin <lasse.collin@tukaani.org> Reviewed-by: Sam James <sam@gentoo.org> Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Joel Stanley <joel@jms.id.au> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Emil Renner Berthing <emil.renner.berthing@canonical.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Jubin Zhong <zhongjubin@huawei.com> Cc: Jules Maselbas <jmaselbas@zdiv.net> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Rui Li <me@lirui.org> Cc: Simon Glass <sjg@chromium.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While building, bpftool makes a skeleton from test_core_extern.c, which
itself includes <stdbool.h> and uses the 'bool' type. However, the skeleton
test_core_extern.skel.h generated *does not* include <stdbool.h> or use the
'bool' type, instead using the C-only '_Bool' type. Compiling test_cpp.cpp
with g++ 12.3 for mips64el/musl-libc then fails with error:
In file included from test_cpp.cpp:9:
test_core_extern.skel.h:45:17: error: '_Bool' does not name a type
45 | _Bool CONFIG_BOOL;
| ^~~~~
This was likely missed previously because glibc uses a GNU extension for
<stdbool.h> with C++ (#define _Bool bool), not supported by musl libc.
Normally, a C fragment would include <stdbool.h> and use the 'bool' type,
and thus cleanly work after import by C++. The ideal fix would be for
'bpftool gen skeleton' to output the correct type/include supporting C++,
but in the meantime add a conditional define as above.
Although the post-increment in macro 'CPU_SET(next++, &cpuset)' seems safe,
the sequencing can raise compile errors, so move the increment outside the
macro. This avoids an error seen using gcc 12.3.0 for mips64el/musl-libc:
In file included from test_lru_map.c:11:
test_lru_map.c: In function 'sched_next_online':
test_lru_map.c:129:29: error: operation on 'next' may be undefined [-Werror=sequence-point]
129 | CPU_SET(next++, &cpuset);
| ^
cc1: all warnings being treated as errors
Remove a redundant include of '<asm/types.h>', whose needed definitions are
already included (via '<linux/types.h>') in cg_storage_multi_egress_only.c,
cg_storage_multi_isolated.c, and cg_storage_multi_shared.c. This avoids
redefinition errors seen compiling for mips64el/musl-libc like:
In file included from progs/cg_storage_multi_egress_only.c:13:
In file included from progs/cg_storage_multi.h:6:
In file included from /usr/mips64el-linux-gnuabi64/include/asm/types.h:23:
/usr/include/asm-generic/int-l64.h:29:25: error: typedef redefinition with different types ('long' vs 'long long')
29 | typedef __signed__ long __s64;
| ^
/usr/include/asm-generic/int-ll64.h:30:44: note: previous definition is here
30 | __extension__ typedef __signed__ long long __s64;
| ^
The type 'loff_t' is a GNU extension and not exposed by the musl 'fcntl.h'
header unless _GNU_SOURCE is defined. Add this definition to fix errors
seen compiling for mips64el/musl-libc:
In file included from tools/testing/selftests/bpf/prog_tests/core_reloc.c:4:
./bpf_testmod/bpf_testmod.h:10:9: error: unknown type name 'loff_t'
10 | loff_t off;
| ^~~~~~
./bpf_testmod/bpf_testmod.h:16:9: error: unknown type name 'loff_t'
16 | loff_t off;
| ^~~~~~
The GNU version of 'struct tcp_info' in 'netinet/tcp.h' is not exposed by
musl headers unless _GNU_SOURCE is defined.
Add this definition to fix errors seen compiling for mips64el/musl-libc:
tcp_rtt.c: In function 'wait_for_ack':
tcp_rtt.c:24:25: error: storage size of 'info' isn't known
24 | struct tcp_info info;
| ^~~~
tcp_rtt.c:24:25: error: unused variable 'info' [-Werror=unused-variable]
cc1: all warnings being treated as errors
The GNU version of 'struct tcphdr' has members 'doff', 'source' and 'dest',
which are not exposed by musl libc headers unless _GNU_SOURCE is defined.
Add this definition to fix errors seen compiling for mips64el/musl-libc:
flow_dissector.c:118:30: error: 'struct tcphdr' has no member named 'doff'
118 | .tcp.doff = 5,
| ^~~~
flow_dissector.c:119:30: error: 'struct tcphdr' has no member named 'source'
119 | .tcp.source = 80,
| ^~~~~~
flow_dissector.c:120:30: error: 'struct tcphdr' has no member named 'dest'
120 | .tcp.dest = 8080,
| ^~~~
The GNU version of 'struct tcphdr' with member 'doff' is not exposed by
musl headers unless _GNU_SOURCE is defined. Add this definition to fix
errors seen compiling for mips64el/musl-libc:
In file included from kfree_skb.c:2:
kfree_skb.c: In function 'on_sample':
kfree_skb.c:45:30: error: 'struct tcphdr' has no member named 'doff'
45 | if (CHECK(pkt_v6->tcp.doff != 5, "check_tcp",
| ^
Add a "bpf_util.h" include to avoid the following error seen compiling for
mips64el with musl libc:
bench.c: In function 'find_benchmark':
bench.c:590:25: error: implicit declaration of function 'ARRAY_SIZE' [-Werror=implicit-function-declaration]
590 | for (i = 0; i < ARRAY_SIZE(benchs); i++) {
| ^~~~~~~~~~
cc1: all warnings being treated as errors
Existing code calls getsockname() with a 'struct sockaddr_in6 *' argument
where a 'struct sockaddr *' argument is declared, yielding compile errors
when building for mips64el/musl-libc:
bpf_iter_setsockopt.c: In function 'get_local_port':
bpf_iter_setsockopt.c:98:30: error: passing argument 2 of 'getsockname' from incompatible pointer type [-Werror=incompatible-pointer-types]
98 | if (!getsockname(fd, &addr, &addrlen))
| ^~~~~
| |
| struct sockaddr_in6 *
In file included from .../netinet/in.h:10,
from .../arpa/inet.h:9,
from ./test_progs.h:17,
from bpf_iter_setsockopt.c:5:
.../sys/socket.h:391:23: note: expected 'struct sockaddr * restrict' but argument is of type 'struct sockaddr_in6 *'
391 | int getsockname (int, struct sockaddr *__restrict, socklen_t *__restrict);
| ^
cc1: all warnings being treated as errors
This compiled under glibc only because the argument is declared to be a
"funky" transparent union which includes both types above. Explicitly cast
the argument to allow compiling for both musl and glibc.
Cast 'rlim_t' argument to match expected type of printf() format and avoid
compile errors seen building for mips64el/musl-libc:
In file included from map_tests/sk_storage_map.c:20:
map_tests/sk_storage_map.c: In function 'test_sk_storage_map_stress_free':
map_tests/sk_storage_map.c:414:56: error: format '%lu' expects argument of type 'long unsigned int', but argument 2 has type 'rlim_t' {aka 'long long unsigned int'} [-Werror=format=]
414 | CHECK(err, "setrlimit(RLIMIT_NOFILE)", "rlim_new:%lu errno:%d",
| ^~~~~~~~~~~~~~~~~~~~~~~
415 | rlim_new.rlim_cur, errno);
| ~~~~~~~~~~~~~~~~~
| |
| rlim_t {aka long long unsigned int}
./test_maps.h:12:24: note: in definition of macro 'CHECK'
12 | printf(format); \
| ^~~~~~
map_tests/sk_storage_map.c:414:68: note: format string is defined here
414 | CHECK(err, "setrlimit(RLIMIT_NOFILE)", "rlim_new:%lu errno:%d",
| ~~^
| |
| long unsigned int
| %llu
cc1: all warnings being treated as errors
tpm_dev_transmit prepares the TPM space before attempting command
transmission. However if the command fails no rollback of this
preparation is done. This can result in transient handles being leaked
if the device is subsequently closed with no further commands performed.
Fix this by flushing the space in the event of command transmission
failure.
Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces") Signed-off-by: Jonathan McDowell <noodles@meta.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When checking a memory buffer to be consecutive in machine memory,
the alignment needs to be checked, too. Failing to do so might result
in DMA memory not being aligned according to its requested size,
leading to error messages like:
4xxx 0000:2b:00.0: enabling device (0140 -> 0142)
4xxx 0000:2b:00.0: Ring address not aligned
4xxx 0000:2b:00.0: Failed to initialise service qat_crypto
4xxx 0000:2b:00.0: Resetting device qat_dev0
4xxx: probe of 0000:2b:00.0 failed with error -14
When running as a Xen PV dom0 the kernel is loaded by the hypervisor
using a different memory map than that of the host. In order to
minimize the required changes in the kernel, the kernel adapts its
memory map to that of the host. In order to do that it is checking
for conflicts of its load address with the host memory map.
Unfortunately the tested memory range does not include the .brk
area, which might result in crashes or memory corruption when this
area does conflict with the memory map of the host.
Fix the test by using the _end label instead of __bss_stop.
Fixes: 808fdb71936c ("xen: check for kernel memory conflicting with memory layout") Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is another cause for soft lock-up of GPU in empty ring-buffer:
race between GPU executing last commands and CPU checking ring for
emptiness. On GPU side IRQ for retire is triggered by CACHE_FLUSH_TS
event and RPTR shadow (which is used to check ring emptiness) is updated
a bit later from CP_CONTEXT_SWITCH_YIELD. Thus if GPU is executing its
last commands slow enough or we check that ring too fast we will miss a
chance to trigger switch to lower priority ring because current ring isn't
empty just yet. This can escalate to lock-up situation described in
previous patch.
To work-around this issue we keep track of last submit sequence number
for each ring and compare it with one written to memptrs from GPU during
execution of CACHE_FLUSH_TS event.
Fixes: b1fc2839d2f9 ("drm/msm: Implement preemption for A5XX targets") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612047/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
cur_ctx_seqno already does the same thing, but handles the edge cases
where a refcnt'd context can live after lastclose. So let's not have
two ways to do the same thing.
Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org> Link: https://lore.kernel.org/r/20211109181117.591148-3-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Stable-dep-of: a30f9f65b5ac ("drm/msm/a5xx: workaround early ring-buffer emptiness check") Signed-off-by: Sasha Levin <sashal@kernel.org>
On A5XX GPUs when preemption is used it's invietable to enter a soft
lock-up state in which GPU is stuck at empty ring-buffer doing nothing.
This appears as full UI lockup and not detected as GPU hang (because
it's not). This happens due to not triggering preemption when it was
needed. Sometimes this state can be recovered by some new submit but
generally it won't happen because applications are waiting for old
submits to retire.
One of the reasons why this happens is a race between a5xx_submit and
a5xx_preempt_trigger called from IRQ during submit retire. Former thread
updates ring->cur of previously empty and not current ring right after
latter checks it for emptiness. Then both threads can just exit because
for first one preempt_state wasn't NONE yet and for second one all rings
appeared to be empty.
To prevent such situations from happening we need to establish guarantee
for preempt_trigger to make decision after each submit or retire. To
implement this we serialize preemption initiation using spinlock. If
switch is already in progress we need to re-trigger preemption when it
finishes.
Fixes: b1fc2839d2f9 ("drm/msm: Implement preemption for A5XX targets") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612045/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Two fields of preempt_record which are used by CP aren't reset on
resume: "data" and "info". This is the reason behind faults which happen
when we try to switch to the ring that was active last before suspend.
In addition those faults can't be recovered from because we use suspend
and resume to do so (keeping values of those fields again).
Fixes: b1fc2839d2f9 ("drm/msm: Implement preemption for A5XX targets") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/612043/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fine grain preemption (switching from/to points within submits)
requires extra handling in command stream of those submits, especially
when rendering with tiling (using GMEM). However this handling is
missing at this point in mesa (and always was). For this reason we get
random GPU faults and hangs if more than one priority level is used
because local preemption is enabled prior to executing command stream
from submit.
With that said it was ahead of time to enable local preemption by
default considering the fact that even on downstream kernel it is only
enabled if requested via UAPI.
Fixes: a7a4c19c36de ("drm/msm/a5xx: fix setting of the CP_PREEMPT_ENABLE_LOCAL register") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612041/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In adreno_request_fw() when debugging information is printed to the log
after firmware load, an incorrect filename is printed. 'newname' is used
instead of 'fwname', so prefix "qcom/" is being added to filename.
Looks like "copy-paste" mistake.
Fix this mistake by replacing 'newname' with 'fwname'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2c41ef1b6f7d ("drm/msm/adreno: deal with linux-firmware fw paths") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/602382/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
