gic_raise_softirq() walks the list of cpus using for_each_cpu(), it calls
gic_compute_target_list() which advances the iterator by the number of
CPUs in the cluster.
If gic_compute_target_list() reaches the last CPU it leaves the iterator
pointing at the last CPU. This means the next time round the for_each_cpu()
loop cpumask_next() will be called with an invalid CPU.
This triggers a warning when built with CONFIG_DEBUG_PER_CPU_MAPS:
[ 3.077738] GICv3: CPU1: found redistributor 1 region 0:0x000000002f120000
[ 3.077943] CPU1: Booted secondary processor [410fd0f0]
[ 3.078542] ------------[ cut here ]------------
[ 3.078746] WARNING: CPU: 1 PID: 0 at ../include/linux/cpumask.h:121 gic_raise_softirq+0x12c/0x170
[ 3.078812] Modules linked in:
[ 3.078869]
[ 3.078930] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc5+ #5188
[ 3.078994] Hardware name: Foundation-v8A (DT)
[ 3.079059] task: ffff80087a1a0080 task.stack: ffff80087a19c000
[ 3.079145] PC is at gic_raise_softirq+0x12c/0x170
[ 3.079226] LR is at gic_raise_softirq+0xa4/0x170
[ 3.079296] pc : [<ffff0000083ead24>] lr : [<ffff0000083eac9c>] pstate: 200001c9
[ 3.081139] Call trace:
[ 3.081202] Exception stack(0xffff80087a19fbe0 to 0xffff80087a19fd10)
Avoid updating the iterator if the next call to cpumask_next() would
cause the for_each_cpu() loop to exit.
There is no change to gic_raise_softirq()'s behaviour, (cpumask_next()s
eventual call to _find_next_bit() will return early as start >= nbits),
this patch just silences the warning.
Fixes: 021f653791ad ("irqchip: gic-v3: Initial support for GICv3") Signed-off-by: James Morse <james.morse@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1474306155-3303-1-git-send-email-james.morse@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
batadv_find_router dereferences last_bonding_candidate from
orig_node without making sure that it has a valid reference. This reference
has to be retrieved by increasing the reference counter while holding
neigh_list_lock. The lock is required to avoid that
batadv_last_bonding_replace removes the current last_bonding_candidate,
reduces the reference counter and maybe destroys the object in this
process.
Fixes: f3b3d9018975 ("batman-adv: add bonding again") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device notifications are not received after the first interface is
closed; since there is an unregister for notifications on every
interface close. Correct this by unregistering for device
notifications only when the last interface is closed. Also, make
all operations on the i40iw_notifiers_registered atomic as it
can be read/modified concurrently.
Update iwqp->hw_iwarp_state to reflect the new state of the CQP
modify QP operation. This avoids reissuing a CQP operation to
modify a QP to a state that it is already in.
Fixes: 4e9042e647ff ("i40iw: add hw and utils files") Reported-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Send a zero length last streaming mode message for loopback
connections to synchronize between accepting QP and connecting QP.
This avoids data transfer to start on the accepting QP before
the connecting QP is in RTS. Also remove function i40iw_loopback_nop()
as it is no longer used.
Add NULL check for pdata and pdata->addr before the memcpy in
i40iw_form_cm_frame(). This fixes a NULL pointer de-reference
which occurs when the MPA private data pointer is NULL. Also
only copy pdata->size bytes in the memcpy to prevent reading
past the length of the private data buffer provided by upper layer.
iwpbl->iwmr points to the structure that contains iwpbl,
which is iwmr. Setting this to NULL would result in
writing to freed memory. So just free iwmr, and return.
Fixes: d37498417947 ("i40iw: add files for iwarp interface") Reported-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory allocated for iwqp; iwqp->allocated_buffer is freed twice in
the create_qp error path. Correct this by having it freed only once in
i40iw_free_qp_resources().
iwdev->mem_resources is incorrectly defined as an unsigned
long instead of u8. As a result, the offset into the dynamic
allocated structures in i40iw_initialize_hw_resources() is
incorrectly calculated and would lead to writing of memory
regions outside of the allocated buffer.
The A-MSDU TX code (within TXQs) didn't always check the return value
of skb_linearize() properly, resulting in potentially passing a frag-
list SKB down to the driver even when it said it can't handle it. Fix
that.
ucb1x00 has used IRQ probing since it's dawn to find the GPIO interrupt
that it's connected to. However, commit 23393d49fb75 ("gpio: kill off
set_irq_flags usage") broke this by disabling IRQ probing on GPIO
interrupts. Fix this.
Fixes: 23393d49fb75 ("gpio: kill off set_irq_flags usage") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Fixes: 10b2b2019d81 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a pretty ancient bug that hasn't manifested itself
until now.
The scratchbuf for command queue is allocated only for 32 slots
but is accessed with the queue write pointer - which can be
up to 256.
Since the scratch buf size was 16 and there are up to 256 TFDs
we never passed a page boundary when accessing the scratch buffer,
but when attempting to increase the size of the scratch buffer a
panic was quick to follow when trying to access the address resulted
in a page boundary.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Fixes: 38c0f334b359 ("iwlwifi: use coherent DMA memory for command header") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.
In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
The conversion from a look-up table to a calculation for clock generator
parameters forgot to take into account that BRDV x 1/1 is valid only if
BRPS is x 1/1 or x 1/2, leading to undefined behavior (e.g. arbitrary
clock rates).
This limitation is documented for the MSIOF module in all supported
SH/R-Mobile and R-Car Gen2/Gen3 ARM SoCs.
Tested on r8a7791/koelsch and r8a7795/salvator-x.
Fixes: 65d5665bb260b034 ("spi: sh-msiof: Update calculation of frequency dividing") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
e9532e69b8d1 ("sched/cputime: Fix steal time accounting vs. CPU hotplug")
... set rq->prev_* to 0 after a CPU hotplug comes back, in order to
fix the case where (after CPU hotplug) steal time is smaller than
rq->prev_steal_time.
However, this should never happen. Steal time was only smaller because of the
KVM-specific bug fixed by the previous patch. Worse, the previous patch
triggers a bug on CPU hot-unplug/plug operation: because
rq->prev_steal_time is cleared, all of the CPU's past steal time will be
accounted again on hot-plug.
Since the root cause has been fixed, we can just revert commit e9532e69b8d1.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 'commit e9532e69b8d1 ("sched/cputime: Fix steal time accounting vs. CPU hotplug")' Link: http://lkml.kernel.org/r/1465813966-3116-3-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345c2 ("hwmon: Add driver for ADT7411 voltage and temperature sensor") Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem_cell_read() is declared as void * if CONFIG_NVMEM is enabled, and
as char * otherwise. This can result in a build warning if CONFIG_NVMEM
is not enabled and a caller asigns the result to a type other than char *
without using a typecast. Use a consistent declaration to avoid the
problem.
To support UHS modes for Tegra an external regulator must be present
to adjust the IO voltage accordingly. Even if the regulator is not
present but the host supports the UHS modes and the device supports the
UHS modes, then we will attempt to switch to a high-speed mode. Without
an external regulator, Tegra will fail to switch to the high-speed
mode.
It has been found that with some SD cards, that once it has been switch
to operate at a high-speed mode, all subsequent commands issues to the
card will fail and so it will not be possible to switch back to a non
high-speed mode and so the SD card initialisation will fail.
The SDHCI core does not require that the host have an external regulator
when switching to UHS modes and therefore, the Tegra SDHCI host
controller should only advertise the UHS modes as being supported if the
regulator for the IO voltage is present. Fortunately, Tegra has a vendor
specific register which can be used to control which modes are
advertised via the SDHCI_CAPABILITIES register. Hence, if there is no IO
voltage regulator available for the Tegra SDHCI host, then don't
advertise the UHS modes.
Note that if the regulator is not available, we also don't advertise that
the SDHCI is compatible with v3.0 of the SDHCI specification because
this will read the SDHCI_CAPABILITIES_1 register which will enable other
UHS modes.
This fixes commit 7ad2ed1dfcbe ("mmc: tegra: enable UHS-I modes") which
enables UHS mode without checking if the board can support them.
When tearing down an AUX buf for an event via perf_mmap_close(),
__perf_event_output_stop() is called on the event's CPU to ensure that
trace generation is halted before the process of unmapping and
freeing the buffer pages begins.
The callback is performed via cpu_function_call(), which ensures that it
runs with interrupts disabled and is therefore not preemptible.
Unfortunately, the current code grabs the per-cpu context pointer using
get_cpu_ptr(), which unnecessarily disables preemption and doesn't pair
the call with put_cpu_ptr(), leading to a preempt_count() imbalance and
a BUG when freeing the AUX buffer later on:
0day found a boot warning triggered in rcu_perf_writer() on !SMP kernel:
WARN_ON(rcu_gp_is_normal() && gp_exp);
, the root cause of which is trying to measure expedited grace
periods(by setting gp_exp to true by default) when all the grace periods
are normal(TINY RCU only has normal grace periods).
However, such a mis-setting would only result in failing to measure the
performance for a specific kind of grace periods, therefore using a
WARN_ON to check this is a little overkilling. We could handle this
inside rcuperf module via some error messages to tell users about the
mis-settings.
Therefore this patch removes the WARN_ON in rcu_perf_writer() and
handles those checkings in rcu_perf_init() with plain if() code.
Moreover, this patch changes the default value of gp_exp to 1) align
with rcutorture tests and 2) make the default setting work for all RCU
implementations by default.
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Boqun Feng <boqun.feng@gmail.com> Fixes: http://lkml.kernel.org/r/57411b10.mFvG0+AgcrMXGtcj%fengguang.wu@intel.com Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function i40e_debug_aq parameter desc is assumed to be
possibly NULL. Do not dereference it before checking the
value.
Fixes: f905dd62be88 ("i40e/i40evf: add max buf len to aq debug print helper") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6ce0d2001692 ("ARM: dma: Use dma_pfn_offset for dma address translation"),
dma_to_pfn() already returns the PFN with the physical memory start offset
so we don't need to add it again.
This fixes USB mass storage lock-up problem on systems that can't do DMA
over the entire physical memory range (e.g.) Keystone 2 systems with 4GB RAM
can only do DMA over the first 2GB. [K2E-EVM].
What happens there is that without this patch SCSI layer sets a wrong
bounce buffer limit in scsi_calculate_bounce_limit() for the USB mass
storage device. dma_max_pfn() evaluates to 0x8fffff and bounce_limit
is set to 0x8fffff000 whereas maximum DMA'ble physical memory on Keystone 2
is 0x87fffffff. This results in non DMA'ble pages being given to the
USB controller and hence the lock-up.
NOTE: in the above case, USB-SCSI-device's dma_pfn_offset was showing as 0.
This should have really been 0x780000 as on K2e, LOWMEM_START is 0x80000000
and HIGHMEM_START is 0x800000000. DMA zone is 2GB so dma_max_pfn should be
0x87ffff. The incorrect dma_pfn_offset for the USB storage device is because
USB devices are not correctly inheriting the dma_pfn_offset from the
USB host controller. This will be fixed by a separate patch.
Fixes: 6ce0d2001692 ("ARM: dma: Use dma_pfn_offset for dma address translation") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Olof Johansson <olof@lixom.net> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Linus Walleij <linus.walleij@linaro.org> Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whilst MPIDR values themselves are less than 32 bits, it is still
perfectly valid for a DT to have #address-cells > 1 in the CPUs node,
resulting in the "reg" property having leading zero cell(s). In that
situation, the big-endian nature of the data conspires with the current
behaviour of only reading the first cell to cause the kernel to think
all CPUs have ID 0, and become resoundingly unhappy as a consequence.
Take the full property length into account when parsing CPUs so as to
be correct under any circumstances.
Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udl damage handler is supposed to render 'height' lines, but its
iterator has an obvious typo that makes it miss most lines if the
rectangle does not cover 0/0.
Fix the damage handler to correctly render all lines.
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
The oom victim cannot terminate because it needs to take mmap_sem for
write while the lock is held by ksmd for read which loops in the page
allocator
ksm_do_scan
scan_get_next_rmap_item
down_read
get_next_rmap_item
alloc_rmap_item #ksmd will loop permanently.
There is no way forward because the oom victim cannot release any memory
in 4.1 based kernel. Since 4.6 we have the oom reaper which would solve
this problem because it would release the memory asynchronously.
Nevertheless we can relax alloc_rmap_item requirements and use
__GFP_NORETRY because the allocation failure is acceptable as ksm_do_scan
would just retry later after the lock got dropped.
Such a patch would be also easy to backport to older stable kernels which
do not have oom_reaper.
While we are at it add GFP_NOWARN so the admin doesn't have to be alarmed
by the allocation failure.
This fixes subpage writes when using 4-bit HW ECC.
There has been numerous reports about ECC errors with devices using this
driver for a while. Also the 4-bit ECC has been reported as broken with
subpages in [1] and with 16 bits NANDs in the driver and in mach* board
files both in mainline and in the vendor BSPs.
What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to
try reinitializing the ECC engine:
- R/W on whole pages properly generates/checks RS code
- try writing the 1st subpage only of a blank page, the subpage is well
written and the RS code properly generated, re-reading the same page
the HW detects some ECC error, reading the same page again no ECC
error is detected
Note that the ECC engine is already reinitialized in the 1-bit case.
Tested on my LCDK with UBI+UBIFS using subpages.
This could potentially get rid of the issue workarounded in [1].
[1] 28c015a9daab ("mtd: davinci-nand: disable subpage write for keystone-nand")
Fixes: 6a4123e581b3 ("mtd: nand: davinci_nand, 4-bit ECC for smallpage") Signed-off-by: Karl Beldan <kbeldan@baylibre.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
be7635e7287e ("arch, ftrace: for KASAN put hard/soft IRQ entries into
separate sections") added .softirqentry.text section, but it was not added
to recordmcount. So functions in the section are untracable. Add the
section to scripts/recordmcount.c and scripts/recordmcount.pl.
Fixes: be7635e7287e ("arch, ftrace: for KASAN put hard/soft IRQ entries into separate sections") Link: http://lkml.kernel.org/r/1474902626-73468-1-git-send-email-dvyukov@google.com Signed-off-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Steve Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the v2 hierarchy, "cgroup.subtree_control" rejects controller
enables if the cgroup has processes in it. The enforcement of this
logic assumes that the cgroup wouldn't have any css_sets associated
with it if there are no tasks in the cgroup, which is no longer true
since a79a908fd2b0 ("cgroup: introduce cgroup namespaces").
When a cgroup namespace is created, it pins the css_set of the
creating task to use it as the root css_set of the namespace. This
extra reference stays as long as the namespace is around and makes
"cgroup.subtree_control" think that the namespace root cgroup is not
empty even when it is and thus reject controller enables.
Fix it by making cgroup_subtree_control() walk and test emptiness of
each css_set instead of testing whether the list_head is empty.
While at it, update the comment of cgroup_task_count() to indicate
that the returned value may be higher than the number of tasks, which
has always been true due to temporary references and doesn't break
anything.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Evgeny Vereshchagin <evvers@ya.ru> Cc: Serge E. Hallyn <serge.hallyn@ubuntu.com> Cc: Aditya Kali <adityakali@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Fixes: a79a908fd2b0 ("cgroup: introduce cgroup namespaces") Link: https://github.com/systemd/systemd/pull/3589#issuecomment-249089541 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A discrepancy between cpu_online_mask and cpuset's effective_cpus
mask is inevitable during hotplug since cpuset defers updating of
effective_cpus mask using a workqueue, during which time nothing
prevents the system from more hotplug operations. For that reason
guarantee_online_cpus() walks up the cpuset hierarchy until it finds
an intersection under the assumption that top cpuset's effective_cpus
mask intersects with cpu_online_mask even with such a race occurring.
However a sequence of CPU hotplugs can open a time window, during which
none of the effective CPUs in the top cpuset intersect with
cpu_online_mask.
For example when there are 4 possible CPUs 0-3 and only CPU0 is online:
======================== ===========================
cpu_online_mask top_cpuset.effective_cpus
======================== ===========================
echo 1 > cpu2/online.
CPU hotplug notifier woke up hotplug work but not yet scheduled.
[0,2] [0]
echo 0 > cpu0/online.
The workqueue is still runnable.
[2] [0]
======================== ===========================
Now there is no intersection between cpu_online_mask and
top_cpuset.effective_cpus. Thus invoking sys_sched_setaffinity() at
this moment can cause following:
Unable to handle kernel NULL pointer dereference at virtual address 000000d0
------------[ cut here ]------------
Kernel BUG at ffffffc0001389b0 [verbose debug info unavailable]
Internal error: Oops - BUG: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 1420 Comm: taskset Tainted: G W 4.4.8+ #98
task: ffffffc06a5c4880 ti: ffffffc06e124000 task.ti: ffffffc06e124000
PC is at guarantee_online_cpus+0x2c/0x58
LR is at cpuset_cpus_allowed+0x4c/0x6c
<snip>
Process taskset (pid: 1420, stack limit = 0xffffffc06e124020)
Call trace:
[<ffffffc0001389b0>] guarantee_online_cpus+0x2c/0x58
[<ffffffc00013b208>] cpuset_cpus_allowed+0x4c/0x6c
[<ffffffc0000d61f0>] sched_setaffinity+0xc0/0x1ac
[<ffffffc0000d6374>] SyS_sched_setaffinity+0x98/0xac
[<ffffffc000085cb0>] el0_svc_naked+0x24/0x28
The top cpuset's effective_cpus are guaranteed to be identical to
cpu_online_mask eventually. Hence fall back to cpu_online_mask when
there is no intersection between top cpuset's effective_cpus and
cpu_online_mask.
On May 4th, Bjørn Mork provided patch 697bbc7b8320 ("builddeb: include
objtool binary in headers package"). However, that one only works if
$srctree=$objtree, because the objtool binaries are not written to the
srctree, but to the objtree.
Signed-off-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Fixes: 697bbc7b8320 ("builddeb: include objtool binary in headers package") Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There exists a race where the application can setup a connection
and then disconnect it before iw_cxgb4 processes the fw4_ack
message. For passive side connections, the fw4_ack message is
used to know when to stop the ep timer for MPA_REPLY messages.
If the application disconnects before the fw4_ack is handled then
c4iw_ep_disconnect() needs to clean up the timer state and stop the
timer before restarting it for the disconnect timer. Failure to do this
results in a "timer already started" message and a premature stopping
of the disconnect timer.
Fixes: e4b76a2 ("RDMA/iw_cxgb4: stop_ep_timer() after MPA negotiation") Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we call quarantine_reduce() for ___GFP_KSWAPD_RECLAIM (implied
by __GFP_RECLAIM) allocation. So, basically we call it on almost every
allocation. quarantine_reduce() sometimes is heavy operation, and
calling it with disabled interrupts may trigger hard LOCKUP:
If the total amount of memory assigned to quarantine is less than the
amount of memory assigned to per-cpu quarantines, |new_quarantine_size|
may overflow. Instead, set it to zero.
Commit 0259f522e04f ('soc/tegra: pmc: Restore base address on probe
failure') fixes an issue where the PMC base address pointer is not
restored on probe failure. However, this fix creates another problem
where if early initialisation of the PMC driver fails and an initial
mapping for the PMC address space is not created, then when the PMC
device is probed, the PMC base address pointer will not be valid and
this will cause a crash when tegra_pmc_init() is called and attempts
to access a register.
Although the PMC address space is mapped a 2nd time during the probe
and so this could be fixed by populating the base address pointer
earlier during the probe, this adds more complexity to the code.
Moreover, the PMC probe also assumes the the soc data pointer is also
initialised when the device is probed and if not will also lead to a
crash when calling tegra_pmc_init_tsense_reset(). Given that if the
early initialisation does fail then something bad has happen, it seems
acceptable to allow the PMC device probe to fail as well. Therefore, if
the PMC base address pointer or soc data pointer are not valid when
probing the PMC device, WARN and return an error.
Fixes: 0259f522e04f ('soc/tegra: pmc: Restore base address on probe failure') Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com> Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency) Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 16369564915a ("ixgbe: Add support for VLAN promiscuous with SR-IOV") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.
Fixes: 39e7213edc4f3 ("max17042_battery: Support regmap to access device's registers") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtree_next_node() walks the linked list of leaf nodes to find the next
block of pages in the struct memory_bitmap. If it walks off the end of
the list of nodes, it walks the list of memory zones to find the next
region of memory. If it walks off the end of the list of zones, it
returns false.
This leaves the struct bm_position's node and zone pointers pointing
at their respective struct list_heads in struct mem_zone_bm_rtree.
memory_bm_find_bit() uses struct bm_position's node and zone pointers
to avoid walking lists and trees if the next bit appears in the same
node/zone. It handles these values being stale.
Swap rtree_next_node()s 'step then test' to 'test-next then step',
this means if we reach the end of memory we return false and leave
the node and zone pointers as they were.
This fixes a panic on resume using AMD Seattle with 64K pages:
[ 6.868732] Freezing user space processes ... (elapsed 0.000 seconds) done.
[ 6.875753] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds)
[ 6.896453] PM: Using 3 thread(s) for decompression.
[ 6.896453] PM: Loading and decompressing image data (5339 pages)...
[ 7.318890] PM: Image loading progress: 0%
[ 7.323395] Unable to handle kernel paging request at virtual address 00800040
[ 7.330611] pgd = ffff000008df0000
[ 7.334003] [00800040] *pgd=00000083fffe0003, *pud=00000083fffe0003, *pmd=00000083fffd0003, *pte=0000000000000000
[ 7.344266] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 7.349825] Modules linked in:
[ 7.352871] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G W I 4.8.0-rc1 #4737
[ 7.360512] Hardware name: AMD Overdrive/Supercharger/Default string, BIOS ROD1002C 04/08/2016
[ 7.369109] task: ffff8003c0220000 task.stack: ffff8003c0280000
[ 7.375020] PC is at set_bit+0x18/0x30
[ 7.378758] LR is at memory_bm_set_bit+0x24/0x30
[ 7.383362] pc : [<ffff00000835bbc8>] lr : [<ffff0000080faf18>] pstate: 60000045
[ 7.390743] sp : ffff8003c0283b00
[ 7.473551]
[ 7.475031] Process swapper/0 (pid: 1, stack limit = 0xffff8003c0280020)
[ 7.481718] Stack: (0xffff8003c0283b00 to 0xffff8003c0284000)
[ 7.800075] Call trace:
[ 7.887097] [<ffff00000835bbc8>] set_bit+0x18/0x30
[ 7.891876] [<ffff0000080fb038>] duplicate_memory_bitmap.constprop.38+0x54/0x70
[ 7.899172] [<ffff0000080fcc40>] snapshot_write_next+0x22c/0x47c
[ 7.905166] [<ffff0000080fe1b4>] load_image_lzo+0x754/0xa88
[ 7.910725] [<ffff0000080ff0a8>] swsusp_read+0x144/0x230
[ 7.916025] [<ffff0000080fa338>] load_image_and_restore+0x58/0x90
[ 7.922105] [<ffff0000080fa660>] software_resume+0x2f0/0x338
[ 7.927752] [<ffff000008083350>] do_one_initcall+0x38/0x11c
[ 7.933314] [<ffff000008b40cc0>] kernel_init_freeable+0x14c/0x1ec
[ 7.939395] [<ffff0000087ce564>] kernel_init+0x10/0xfc
[ 7.944520] [<ffff000008082e90>] ret_from_fork+0x10/0x40
[ 7.949820] Code: d28000228b400c21f98000319ac32043 (c85f7c22)
[ 7.955909] ---[ end trace 0024a5986e6ff323 ]---
[ 7.960529] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Here struct mem_zone_bm_rtree's start_pfn has been returned instead of
struct rtree_node's addr as the node/zone pointers are corrupt after
we walked off the end of the lists during mark_unsafe_pages().
This behaviour was exposed by commit 6dbecfd345a6 ("PM / hibernate:
Simplify mark_unsafe_pages()"), which caused mark_unsafe_pages() to call
duplicate_memory_bitmap(), which uses memory_bm_find_bit() after walking
off the end of the memory bitmap.
Fixes: 3a20cb177961 (PM / Hibernate: Implement position keeping in radix tree) Signed-off-by: James Morse <james.morse@arm.com>
[ rjw: Subject ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore the processor state before calling any other functions to
ensure per-CPU variables can be used with KASLR memory randomization.
Tracing functions use per-CPU variables (GS based on x86) and one was
called just before restoring the processor state fully. It resulted
in a double fault when both the tracing & the exception handler
functions tried to use a per-CPU variable.
Fixes: bb3632c6101b (PM / sleep: trace events for suspend/resume) Reported-and-tested-by: Borislav Petkov <bp@suse.de> Reported-by: Jiri Kosina <jikos@kernel.org> Tested-by: Rafael J. Wysocki <rafael@kernel.org> Tested-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Garnier <thgarnie@google.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function ceph_alloc_page_vector() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Fixes: 1907920324f1 ('libceph: support for sending notifies') Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ceph_llseek does not correctly return NXIO errors because the 'out' path
always returns 'offset'.
Fixes: 06222e491e66 ("fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Yan, Zheng <zyan@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The genksyms helper in the kernel cannot parse a type definition
like "typeof(((type *)0)->keyfld)" that is used in the DEFINE_RB_FUNCS
helper, causing the following EXPORT_SYMBOL() statement to be ignored
when computing the crcs, and triggering a warning about this:
WARNING: "ceph_monc_do_statfs" [fs/ceph/ceph.ko] has no CRC
To work around the problem, we can rewrite the type to reference
an undefined 'extern' symbol instead of a NULL pointer. This is
evidently ok for genksyms, and it no longer complains about the
line when calling it with 'genksyms -w'.
I've looked briefly into extending genksyms instead, but it seems
really hard to do. Jan Beulich introduced basic support for 'typeof'
a while ago in dc53324060f3 ("genksyms: fix typeof() handling"),
but that is not sufficient for the expression we have here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: fcd00b68bbe2 ("libceph: DEFINE_RB_FUNCS macro") Cc: Jan Beulich <jbeulich@suse.com> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An on-stack oid in ceph_ioctl_get_dataloc() is not initialized,
resulting in a WARN and a NULL pointer dereference later on. We will
have more of these on-stack in the future, so fix it with a convenience
macro.
There's a mixture of signed 32-bit and unsigned 32-bit and 64-bit data
types used for keeping track of how many pages have been mapped.
This leads to hangs during boot when mapping large numbers of pages
(multiple terabytes, as reported by Waiman) because those values are
interpreted as being negative.
commit 742563777e8d ("x86/mm/pat: Avoid truncation when converting
cpa->numpages to address") fixed one of those bugs, but there is
another lurking in __change_page_attr_set_clr().
Additionally, the return value type for the populate_*() functions can
return negative values when a large number of pages have been mapped,
triggering the error paths even though no error occurred.
Consistently use 64-bit types on 64-bit platforms when counting pages.
Even in the signed case this gives us room for regions 8PiB
(pebibytes) in size whilst still allowing the usual negative value
error checking idiom.
cpu_has_fpu macro uses smp_processor_id() and is currently executed
with preemption enabled, that triggers the warning at runtime.
It is assumed throughout the kernel that if any CPU has an FPU, then all
CPUs would have an FPU as well, so it is safe to perform the check with
preemption enabled - change the code to use raw_ variant of the check to
avoid the warning.
Commit c1a0e9bc885d ("MIPS: Allow compact branch policy to be changed")
added Kconfig entries allowing for the compact branch policy used by the
compiler for MIPSr6 kernels to be specified. This can be useful for
debugging, particularly in systems where compact branches have recently
been introduced.
Unfortunately mainline gcc 5.x supports MIPSr6 but not the
-mcompact-branches compiler flag, leading to MIPSr6 kernels failing to
build with gcc 5.x with errors such as:
Fixing this by hiding the Kconfig entry behind another seems to be more
hassle than it's worth, as MIPSr6 & compact branches have been around
for a while now and if policy does need to be set for debug it can be
done easily enough with KCFLAGS. Therefore remove the compact branch
policy Kconfig entries & their handling in the Makefile.
This reverts commit c1a0e9bc885d ("MIPS: Allow compact branch policy to
be changed").
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: c1a0e9bc885d ("MIPS: Allow compact branch policy to be changed") Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14241/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The page structures associated with the vDSO pages in the kernel image
are calculated using virt_to_page(), which uses __pa() under the hood to
find the pfn associated with the virtual address. The vDSO data pointers
however point to kernel symbols, so __pa_symbol() should really be used
instead.
Since there is no equivalent to virt_to_page() which uses __pa_symbol(),
fix init_vdso_image() to work directly with pfns, calculated with
__phys_to_pfn(__pa_symbol(...)).
This issue broke the Malta Enhanced Virtual Addressing (EVA)
configuration which has a non-default implementation of __pa_symbol().
This is because it uses a physical alias so that the kernel executes
from KSeg0 (VA 0x80000000 -> PA 0x00000000), while RAM is provided to
the kernel in the KUSeg range (VA 0x00000000 -> PA 0x80000000) which
uses the same underlying RAM.
Since there are no page structures associated with the low physical
address region, some arbitrary kernel memory would be interpreted as a
page structure for the vDSO pages and badness ensues.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14229/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the possibility of a deadlock when bringing up
secondary CPUs.
The deadlock occurs because the set_cpu_online() is called before
synchronise_count_slave(). This can cause a deadlock if the boot CPU,
having scheduled another thread, attempts to send an IPI to the
secondary CPU, which it sees has been marked online. The secondary is
blocked in synchronise_count_slave() waiting for the boot CPU to enter
synchronise_count_master(), but the boot cpu is blocked in
smp_call_function_many() waiting for the secondary to respond to it's
IPI request.
Fix this by marking the CPU online in cpu_callin_map and synchronising
counters before declaring the CPU online and calculating the maps for
IPIs.
In the mipsr2_decoder() function, used to emulate pre-MIPSr6
instructions that were removed in MIPSr6, the init_fpu() function is
called if a removed pre-MIPSr6 floating point instruction is the first
floating point instruction used by the task. However, init_fpu()
performs varous actions that rely upon not being migrated. For example
in the most basic case it sets the coprocessor 0 Status.CU1 bit to
enable the FPU & then loads FP register context into the FPU registers.
If the task were to migrate during this time, it may end up attempting
to load FP register context on a different CPU where it hasn't set the
CU1 bit, leading to errors such as:
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Since the device hierarchy domain was added by commit c98c1822ee13
("irqchip/mips-gic: Add device hierarchy domain"), GIC local interrupts
have been broken.
Users attempting to setup a per-cpu local IRQ, for example the GIC timer
clock events code in drivers/clocksource/mips-gic-timer.c, the
setup_percpu_irq function would refuse with -EINVAL because the GIC
irqchip driver never called irq_set_percpu_devid so the
IRQ_PER_CPU_DEVID flag was never set for the IRQ. This happens because
irq_set_percpu_devid was being called from the gic_irq_domain_map
function which is no longer called.
Doing only that runs into further problems because gic_dev_domain_alloc
set the struct irq_chip for all interrupts, local or shared, to
gic_level_irq_controller despite that only being suitable for shared
interrupts. The typical outcome of this is that gic_level_irq_controller
callback functions are called for local interrupts, and then hwirq
number calculations overflow & the driver ends up attempting to access
some invalid register with an address calculated from an invalid hwirq
number. Best case scenario is that this then leads to a bus error. This
is fixed by abstracting the setup of the hwirq & chip to a new function
gic_setup_dev_chip which is used by both the root GIC IRQ domain & the
device domain.
Finally, decoding local interrupts failed because gic_dev_domain_alloc
only called irq_domain_alloc_irqs_parent for shared interrupts. Local
ones were therefore never associated with hwirqs in the root GIC IRQ
domain and the virq in gic_handle_local_int would always be 0. This is
fixed by calling irq_domain_alloc_irqs_parent unconditionally & having
gic_irq_domain_alloc handle both local & shared interrupts, which is
easy due to the aforementioned abstraction of chip setup into
gic_setup_dev_chip.
This fixes use of the MIPS GIC timer for clock events, which has been
broken since c98c1822ee13 ("irqchip/mips-gic: Add device hierarchy
domain") but hadn't been noticed due to a silent fallback to the MIPS
coprocessor 0 count/compare clock events device.
Fixes: c98c1822ee13 ("irqchip/mips-gic: Add device hierarchy domain") Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Jason Cooper <jason@lakedaemon.net> Cc: Qais Yousef <qsyousef@gmail.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/20160913165335.31389-1-paul.burton@imgtec.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waiman reported that booting with CONFIG_EFI_MIXED enabled on his
multi-terabyte HP machine results in boot crashes, because the EFI
region mapping functions loop forever while trying to map those
regions describing RAM.
While this patch doesn't fix the underlying hang, there's really no
reason to map EFI_CONVENTIONAL_MEMORY regions into the EFI page tables
when mixed-mode is not in use at runtime.
If the subvol/snapshot create/destroy ioctls are passed a regular file
with execute permissions set, we'll eventually Oops while trying to do
inode->i_op->lookup via lookup_one_len.
This patch ensures that the file descriptor refers to a directory.
Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.
Fixes: 9a774c78e211 ("cfg80211: Support multiple CSA counters") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Off-channel action frames (such as ANQP frames) must be sent either on
the AUX queue or on the offchannel queue, otherwise the firmware will
cause a SYSASSERT.
In the current implementation, the queue to be used is correctly set in
the original skb, but this is done after it is copied. Thus the copy
remains with the original, incorrect queue.
Fix this by setting the queue in the original skb before copying it.
Fixes: commit 5c08b0f5026f ("iwlwifi: mvm: don't override the rate with the AMSDU len") Signed-off-by: Beni Lev <beni.lev@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
init_tlb_ubc() looked unnecessary to me: tlb_ubc is statically
initialized with zeroes in the init_task, and copied from parent to
child while it is quiescent in arch_dup_task_struct(); so I went to
delete it.
But inserted temporary debug WARN_ONs in place of init_tlb_ubc() to
check that it was always empty at that point, and found them firing:
because memcg reclaim can recurse into global reclaim (when allocating
biosets for swapout in my case), and arrive back at the init_tlb_ubc()
in shrink_node_memcg().
Resetting tlb_ubc.flush_required at that point is wrong: if the upper
level needs a deferred TLB flush, but the lower level turns out not to,
we miss a TLB flush. But fortunately, that's the only part of the
protocol that does not nest: with the initialization removed, cpumask
collects bits from upper and lower levels, and flushes TLB when needed.
Fixes: 72b252aed506 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iter->seq can be reset outside the protection of the mutex. So can
reading of user data. Move the mutex up to the beginning of the function.
Fixes: d7350c3f45694 ("tracing/core: make the read callbacks reentrants") Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since mac80211 doesn't currently support TSIDs 8-15 which can
only be used after QoS TSPEC negotiation (and not even after
WMM negotiation), reject attempts to set up aggregation
sessions for them, which might confuse drivers. In mac80211
we do correctly handle that, but the TSIDs should never get
used anyway, and drivers might not be able to handle it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset value of weekday is 0x1. This is wrong since
the reset values of the day/month/year make up to Jan 1 2001.
When computed weekday comes out to be Monday. On a scale
of 1-7(Sunday - Saturday) it should be 0x2. So we should not
be relying on the reset value.
Hence compute the wday using the current date/month/year values.
Check if reset wday is any different from the computed wday,
If different then set the wday which we computed using
date/month/year values.
Prior to commit 6c96f05c8bb8 ("reset: Make [of_]reset_control_get[_foo]
functions wrappers"), the "optional" functions returned -ENOTSUPP when
CONFIG_RESET_CONTROLLER was not set.
Revert back to the old behavior by changing the new
__devm_reset_control_get() and __of_reset_control_get() functions to
return ERR_PTR(-ENOTSUPP) when compiled without CONFIG_RESET_CONTROLLER.
Otherwise they will return -EINVAL causing users to think that an error
occurred when CONFIG_RESET_CONTROLLER is not set.
Fixes: 6c96f05c8bb8 ("reset: Make [of_]reset_control_get[_foo] functions wrappers") Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In stm_unlock(), the test to determine whether we've fully unlocked the
flash checks for the lock length to be equal to the flash size. That is
a typo/think-o -- the condition actually means the flash is completely
*locked.* We should be using the inverse condition -- that the lock
length is 0 (i.e., no protection).
The result of this bug is that we never actually turn off the Status
Register Write Disable bit, even if the flash is completely unlocked.
Now we can.
Fixes: 47b8edbf0d43 ("mtd: spi-nor: disallow further writes to SR if WP# is low") Reported-by: Giorgio <giorgio.nicole@arcor.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a cut and paste issue here. The bug is that we are allocating
more memory than necessary for msp_maps. We should be allocating enough
space for a map_info struct (144 bytes) but we instead allocate enough
for an mtd_info struct (1840 bytes). It's a small waste.
The other part of this is not harmful but when we allocated msp_flash
then we allocated enough space fro a map_info pointer instead of an
mtd_info pointer. But since pointers are the same size it works out
fine.
Anyway, I decided to clean up all three allocations a bit to make them
a bit more consistent and clear.
Fixes: 68aa0fa87f6d ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a regression accessing the OOB area from the mxc_nand
driver due to an Obiwan error in the mxc_nand_v[12]_ooblayout_free()
functions. They report a bogus oobregion { 64, 7 } which leads to
errors accessing bogus data when reading the oob area.
Prior to the commit the mtd-oobtest module could be run without any
errors. With the offending commit, this test fails with results like:
|Running mtd-oobtest
|
|=================================================
|mtd_oobtest: MTD device: 5
|mtd_oobtest: MTD device size 524288, eraseblock size 131072, page size 2048, count of eraseblocks 4, pages per eraseblock 64, OOB size 64
|mtd_test: scanning for bad eraseblocks
|mtd_test: scanned 4 eraseblocks, 0 are bad
|mtd_oobtest: test 1 of 5
|mtd_oobtest: writing OOBs of whole device
|mtd_oobtest: written up to eraseblock 0
|mtd_oobtest: written 4 eraseblocks
|mtd_oobtest: verifying all eraseblocks
|mtd_oobtest: error @addr[0x0:0x19] 0x9a -> 0x78 diff 0xe2
|mtd_oobtest: error @addr[0x0:0x1a] 0xcc -> 0x0 diff 0xcc
|mtd_oobtest: error @addr[0x0:0x1b] 0xe0 -> 0x85 diff 0x65
|mtd_oobtest: error @addr[0x0:0x1c] 0x60 -> 0x62 diff 0x2
|mtd_oobtest: error @addr[0x0:0x1d] 0x69 -> 0x45 diff 0x2c
|mtd_oobtest: error @addr[0x0:0x1e] 0xcd -> 0xa0 diff 0x6d
|mtd_oobtest: error @addr[0x0:0x1f] 0xf2 -> 0x60 diff 0x92
|mtd_oobtest: error: verify failed at 0x0
[...]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Fixes: a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops") Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wq_numa_init() function makes a private CPU to node map by calling
cpu_to_node() early in the boot process, before the non-boot CPUs are
brought online. Since the default implementation of cpu_to_node()
returns zero for CPUs that have never been brought online, the
workqueue system's view is that *all* CPUs are on node zero.
When the unbound workqueue for a non-zero node is created, the
tsk_cpus_allowed() for the worker threads is the empty set because
there are, in the view of the workqueue system, no CPUs on non-zero
nodes. The code in try_to_wake_up() using this empty cpumask ends up
using the cpumask empty set value of NR_CPUS as an index into the
per-CPU area pointer array, and gets garbage as it is one past the end
of the array. This results in:
Fix by moving call to numa_store_cpu_info() for all CPUs into
smp_prepare_cpus(), which happens before wq_numa_init(). Since
smp_store_cpu_info() now contains only a single function call,
simplify by removing the function and out-lining its contents.
Suggested-by: Robert Richter <rric@kernel.org> Fixes: 1a2db300348b ("arm64, numa: Add NUMA support for arm64 platforms.") Signed-off-by: David Daney <david.daney@cavium.com> Reviewed-by: Robert Richter <rrichter@cavium.com> Tested-by: Yisheng Xie <xieyisheng1@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
