Pavel Kubelun [Wed, 5 Jul 2017 16:23:23 +0000 (19:23 +0300)]
ipq8065: adjust SS USB PHY power settings
According to QSDK ipq8065 has different SS USB PHY power settings.
Adjust it according to QSDK settings.
It also corresponds to oem Netgear R7800 tarball for soc ver >= 2.
https://github.com/paul-chambers/netgear-r7800/blob/eeac2e10190f6f45e32e4c7012c4babc351898d8/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2494
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Pavel Kubelun [Thu, 15 Jun 2017 08:48:17 +0000 (11:48 +0300)]
ipq806x: dwc3: Fix power_on and power_off sequence
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=d316437c9cdb70023a760342678f32e27241725a
The commit fixes:
- dwc3 phy module unloading
- possibly fixes FS#177 when some devices were improperly enumerated as HS while being SS thus stucking the driver during boot.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Pavel Kubelun [Thu, 15 Jun 2017 08:35:26 +0000 (11:35 +0300)]
ipq806x: Update HSIO recommended usb phy settings
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=cf82fdf4bdd081cd81bb081f7815b915bc8bb851
The comit adjusts USB dwc3 phy default values as per QSDK recomendation and allows to set it through DT.
Commit message:
"SoC version based values will be recovered from the device node.
If device node does not have such values, defaults are applied.
Pavel Kubelun [Sat, 9 Dec 2017 17:15:05 +0000 (20:15 +0300)]
ipq806x: update clk and cpufreq drivers
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.
A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).
Following patches are removed:
- 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
- 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
- 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Pavel Kubelun [Thu, 6 Jul 2017 14:20:18 +0000 (17:20 +0300)]
ipq806x: force 2nd pci slot into gen1 mode
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.
In previous commit we've added the support for this option, so enable it in DT for affected devices.
Pavel Kubelun [Fri, 1 Dec 2017 23:26:11 +0000 (02:26 +0300)]
ipq806x: fix wireless regression
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197
This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch
Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.
Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.
Fixes: FS#1197 and probably others Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Jo-Philipp Wich [Sun, 14 Jan 2018 19:06:07 +0000 (20:06 +0100)]
netfilter: enable CONFIG_NF_CONNTRACK_MARK from kmod-nf-conntrack
Unconditionally enable connmark support and tie it to the conntrack core
module to allow removing this kernel configuration dependency from the
xtables-addons package.
Dnsmasq used SIGHUP to do too many things: 1) set dnssec time validation
enabled, 2) bump SOA zone serial, 3) clear dns cache, 4) reload hosts
files, 5) reload resolvers/servers files.
Many subsystems within LEDE can send SIGHUP to dnsmasq: 1) ntpd hotplug
(to indicate time is valid for dnssec) 2) odhcpd (to indicate a
new/removed host - typically DHCPv6 leases) 3) procd on interface state
changes 4) procd on system config state changes, 5) service reload.
If dnssec time validation is enabled before the system clock has been
set to a sensible time, name resolution will fail. Because name
resolution fails, ntpd is unable to resolve time server names to
addresses, so is unable to set time. Classic chicken/egg.
Since commits 23bba9cb330cd298739a16e350b0029ed9429eef (service reload) & 4f02285d8b4a66359a8fa46f22a3efde391b5419 (system config) make it more
likely a SIGHUP will be sent for events other than 'ntpd has set time'
it is more likely that an errant 'name resolution is failing for
everything' situation will be encountered.
Fortunately the upstream dnsmasq people agree and have moved 'check
dnssec timestamp enable' from SIGHUP handler to SIGINT.
Backport the upstream patch to use SIGINT.
ntpd hotplug script updated to use SIGINT.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The blue LED is what other firmwares use for this device, and it's a lot
easier on the eyes than its shade of yellow, which implies an error
condition.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[merge into existing $boardname:blue:status block] Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: Piotr Dymacz <pepe2k@gmail.com> Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
Maxim Anisimov [Tue, 9 Jan 2018 11:25:53 +0000 (14:25 +0300)]
ramips: add support for TP-Link Archer C20 v4
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Flash instruction:
The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Maxim Anisimov [Sat, 13 Jan 2018 07:16:20 +0000 (10:16 +0300)]
ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.
David Bauer [Sat, 16 Dec 2017 14:43:02 +0000 (15:43 +0100)]
ar71xx: fix TP-Link Archer C7 v4 switch LEDs
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.
Mathias Kresin [Sun, 14 Jan 2018 22:21:38 +0000 (23:21 +0100)]
ipq806x: drop ubifs support
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.
Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Hans Dedecker [Sat, 13 Jan 2018 10:05:46 +0000 (11:05 +0100)]
6rd: pass ipcalc as argument to eval
Instead of grepping for NETWORK after calling ipcalc.sh; pass ipcalc.sh as
argument to eval allowing to use $NETWORK to retrieve the IPv4 prefix
(ip4prefix).
ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button
Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)
Unsupported:
- ZT2046Q SPI temperature and voltage sensor
Contributors: Giuseppe Tipaldi (@Ciusss89)
Ricky (@rickydee)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
Piotr Dymacz [Sat, 14 Oct 2017 08:44:39 +0000 (10:44 +0200)]
ramips: add support for ALFA Network AC1200RM
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.
Specification:
- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers
Flash instruction (do it under U-Boot, using UART and TFTP server):
Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.
- mtd layout
- LAN and WAN MAC address setup
- 2.4 GHz Wi-Fi MAC address setup
- 5 GHz Wi-Fi support (calibration data, MAC address setup, missing
ath10k-* packages)
Piotr Dymacz [Thu, 28 Dec 2017 10:07:54 +0000 (11:07 +0100)]
ar71xx: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Piotr Dymacz [Sun, 15 Oct 2017 11:24:02 +0000 (13:24 +0200)]
ar71xx: add support for Teltonika RUT900
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.
There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.
This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector
Serial console pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".
Piotr Dymacz [Fri, 5 Jan 2018 10:35:45 +0000 (11:35 +0100)]
ar71xx: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Piotr Dymacz [Mon, 18 Dec 2017 13:51:28 +0000 (14:51 +0100)]
ar71xx: add support for ALFA Network AP91-5G
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB
Flash instruction:
Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.
Stijn Tintel [Sun, 14 Jan 2018 18:06:55 +0000 (20:06 +0200)]
kernel: move DRM_DEBUG_* symbols to generic config
While working on a new target (meson), the kernel build failed due to
missing DRM_DEBUG_MM_SELFTEST symbol. This can potentially happen on all
targets that enable DRM drivers in the kernel config or via kmod
packages, so add it to the generic config and remove it from x86
subtarget configs, together with DRM_DEBUG_MM.
ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices
This new subtarget sets the small_flash flag and removes unused kernel
configuration.
small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.
ath9k, ath10k(-ct): move spectral scan support under a separate config symbol
Backport patches that separate spectral scan support from general debugfs
support of ath9k/ath10k; this allows to remove the dependency on
KERNEL_RELAY from these driver packages even with debugfs enabled and
avoids the memory footprint of the relay buffers allocated by ath9k/ath10k
even when they aren't used at all.
The KERNEL_RELAY dependency is moved to a new config symbol that enables
spectral scan support in these drivers.
include/package-dumpinfo.mk: don't duplicate source package information for every binary package
Eventually the BUILDONLY package flag could be replaced by simply creating
a package Makefile without any BuildPackage calls. This will fail for now,
as BuildPackage also causes the Makefile's compile target etc. to do
something useful at all.
Package "features" seem to be unused for some time. In any case, custom
Config.in snippets and package PROVIDES are a much more flexible way to
express similar options.
metadata: scripts/feeds: distinguish between source and binary packages, resolve virtual dependencies
Properly resolve build depends to source packages and runtime depends to
binary packages. Dependencies on virtual packages are resolved to the first
provider now.
metadata: always resolve dependencies through provides list
Instead of adding virtual packages to the normal package list, keep a
separate list for provides, make each package provide itself, and resolve
all dependencies through this list. This allows to use PROVIDES to replace
existing packages.
metadata: simplify generation of build depends from runtime depends
Runtime depends cannot have a buildtype suffix, and they never refer to
source package names. In addition, this adds warnings about unsatisfiable
dependencies.
Furthermore, this change fixes the generation of conditional build
dependencies for virtual packages provided by different source packages.
metadata: handle target build depends together with host build depends
Target build depends are similar to host build depends in that they refer
to source packages rather than binary packages. Therefore, it makes sense
to handle them together, rather than putting them in a list together with
runtime depends and trying to figure out if the entries refer to source or
to binary packages afterwards.
This does lead to PKG_BUILD_DEPENDS entries referring to binary package
names not working anymore, which requires some fixes in the package
repositories.
metadata: change pkg->{src} field to hold a reference
We often want to access fields of a source packages through pkg->{src}.
Allow accessing them directly instead of resolving the source hash through
srcpackages.
metadata: interate over source packages when generating Makefile
All build dependencies are between source packages. Interating over source
rather than binary packages simplifies parts of the code and prepares
further improvement.
As a side effect, this changes the implicit default variant of a few
packages (the first defined is used now instead of the lexicographically
first).
John Crispin [Sat, 13 Jan 2018 15:28:42 +0000 (16:28 +0100)]
fstools: update to latest git HEAD
18090d9 overlay: fix compilation with glibc 2a9a6ea libfstools: optimize building directory string for glob de6b026 libfstools: support file paths longer than 255 chars
Koen Vandeputte [Thu, 11 Jan 2018 11:55:02 +0000 (12:55 +0100)]
config: support new symbol intro'd in kernel 4.12
Symbol CONFIG_INITRAMFS_FORCE allows to ignore the value passed by the
bootloader.
By default, all symbols containing INITRAMFS are wiped from the final
config and then re-added conditionally.
Add support for this symbol, as the build will stop otherwise
questioning the user about this option:
* Restart config...
*
*
* General setup
*
Cross-compiler tool prefix (CROSS_COMPILE) []
Compile also drivers which will not load (COMPILE_TEST) [N/y/?] n
...
Initial RAM filesystem and RAM disk (initramfs/initrd) support
(BLK_DEV_INITRD) [Y/n/?] y
Initramfs source file(s) (INITRAMFS_SOURCE) []
Ignore the initramfs passed by the bootloader (INITRAMFS_FORCE)
[N/y/?] (NEW)
Sven Eckelmann [Thu, 30 Nov 2017 13:30:06 +0000 (14:30 +0100)]
ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Sven Eckelmann [Mon, 8 Jan 2018 17:28:51 +0000 (18:28 +0100)]
ipq806x: enable gpio watchdog support
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Sven Eckelmann [Thu, 30 Nov 2017 13:30:06 +0000 (14:30 +0100)]
combined-ext-image.sh: generate image in temp dir
The new build commands operate on the input image and use it again as
output image. This conflicts with the way combined-ext-image.sh was
operating. It required that input and output files are different files and
and that it can write freely to the output file.
This can be avoided when all intermediate build steps by
combined-ext-image.sh are done in a temporary directory. The output file is
then only overwritten in the last step.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Sven Eckelmann [Thu, 30 Nov 2017 13:30:06 +0000 (14:30 +0100)]
mac80211: ath10k: search DT for BDF variant info
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
Luis Araneda [Fri, 5 Jan 2018 13:00:11 +0000 (10:00 -0300)]
ipq806x: convert to dt-based board-detection
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Florian Fainelli [Fri, 12 Jan 2018 22:53:23 +0000 (14:53 -0800)]
armvirt: Resync kernel configuration
The 4.14 kernel configuration defaulted to a v4/v5 multiplatform while
4.9 was using a v6/v7 default configuration. Resync 4.14 against 4.9 so
they are nearly identical.
Commit 30f61a34b4cfd2c676fea4a919e089d6a77254e9 claimed to drop -d & -p
options. In reality only -d was dropped. Update command help text to
reflect that -d is no longer a supported option.
Fixes FS#1187
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
projects / thirdparty / openwrt.git / log
