Since SEV or SNP may already be initialized in the previous kernel,
attempting to initialize them again in the kdump kernel can result
in SNP initialization failures, which in turn lead to IOMMU
initialization failures. Moreover, SNP/SEV guests are not run under a
kdump kernel, so there is no need to initialize SEV or SNP during
kdump boot.
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU device table register is locked and exclusive to the previous
kernel. Attempts to copy old device table from the previous kernel
fails in kdump kernel as hardware ignores writes to the locked device
table base address register as per AMD IOMMU spec Section 2.12.2.1.
This causes the IOMMU driver (OS) and the hardware to reference
different memory locations. As a result, the IOMMU hardware cannot
process the command which results in repeated "Completion-Wait loop
timed out" errors and a second kernel panic: "Kernel panic - not
syncing: timer doesn't work through Interrupt-remapped IO-APIC".
Reuse device table instead of copying device table in case of kdump
boot and remove all copying device table code.
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU command buffers and event buffer registers remain locked and
exclusive to the previous kernel. Attempts to enable command and event
buffers in the kdump kernel will fail, as hardware ignores writes to
the locked MMIO registers as per AMD IOMMU spec Section 2.12.2.1.
Skip enabling command buffers and event buffers for kdump boot as they
are already enabled in the previous kernel.
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU completion wait buffers (CWBs), command buffers and event buffer
registers remain locked and exclusive to the previous kernel. Attempts
to allocate and use new buffers in the kdump kernel fail, as hardware
ignores writes to the locked MMIO registers as per AMD IOMMU spec
Section 2.12.2.1.
This results in repeated "Completion-Wait loop timed out" errors and a
second kernel panic: "Kernel panic - not syncing: timer doesn't work
through Interrupt-remapped IO-APIC"
The list of MMIO registers locked and which ignore writes after failed
SNP shutdown are mentioned in the AMD IOMMU specifications below:
Reuse the pages of the previous kernel for completion wait buffers,
command buffers, event buffers and memremap them during kdump boot
and essentially work with an already enabled IOMMU configuration and
re-using the previous kernel’s data structures.
Reusing of command buffers and event buffers is now done for kdump boot
irrespective of SNP being enabled during kdump.
Re-use of completion wait buffers is only done when SNP is enabled as
the exclusion base register is used for the completion wait buffer
(CWB) address only when SNP is enabled.
Handle the case where the hmm range partially covers a huge page (like
2M), otherwise we can potentially end up doing something nasty like
mapping memory which is outside the range, and maybe not even mapped by
the mm. Fix is based on the xe userptr code, which in a future patch
will directly use gpusvm, so needs alignment here.
v2:
- Add kernel-doc (Matt B)
- s/fls/ilog2/ (Thomas)
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Link: https://lore.kernel.org/r/20250828142430.615826-11-matthew.auld@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After analysis, it appears this is because of the cond_resched()
call from __release_sock().
When current thread is yielding, while still holding the TCP socket lock,
it might regain the cpu after a very long time.
Other peer TLP/RTO is firing (multiple times) and packets are retransmit,
while the initial copy is waiting in the socket backlog or receive queue.
In this patch, I call cond_resched() only once every 16 packets.
Modern TCP stack now spends less time per packet in the backlog,
especially because ACK are no longer sent (commit 133c4c0d3717
"tcp: defer regular ACK while processing socket backlog")
The GuC communication protocol allows GuC to send NO_RESPONSE_RETRY
reply message to indicate that due to some interim condition it can
not handle incoming H2G request and the host shall resend it.
But in some cases, due to errors, this unsatisfied condition might
be final and this could lead to endless retries as it was recently
seen on the CI:
To avoid such dangerous loops allow only limited number of retries
(for now 50) and add some delays (n * 5ms) to slow down the rate of
resending this repeated request.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Stuart Summers <stuart.summers@intel.com> Reviewed-by: Julia Filipchuk <julia.filipchuk@intel.com> Link: https://lore.kernel.org/r/20250903223330.6408-1-michal.wajdeczko@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When the 3.3Vaux supply is present, fetch it at the probe time and keep it
enabled for the entire PCIe controller lifecycle so that the link can enter
L2 state and the devices can signal wakeup using either Beacon or WAKE#
mechanisms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded the subject, description and error message] Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://patch.msgid.link/20250820022328.2143374-1-hongxing.zhu@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In partitioned systems, the domain ID is unique in the partition and a
package can have multiple partitions.
Some user-space tools, such as turbostat, assume the domain ID is unique
per package. These tools map CPU power domains, which are unique to a
package. However, this approach does not work in partitioned systems.
There is no architectural definition of "partition" to present to user
space.
To support these tools, set the domain_id to be unique per package. For
compute die IDs, uniqueness can be achieved using the platform info
cdie_mask, mirroring the behavior observed in non-partitioned systems.
For IO dies, which lack a direct CPU relationship, any unique logical
ID can be assigned. Here domain IDs for IO dies are configured after all
compute domain IDs. During the probe, keep the index of the next IO
domain ID after the last IO domain ID of the current partition. Since
CPU packages are symmetric, partition information is same for all
packages.
The Intel Speed Select driver has already implemented a similar change
to make the domain ID unique, with compute dies listed first, followed
by I/O dies.
Currently, when adding the 6 GHz Band Capabilities element, the channel
list of the wiphy is checked to determine if 6 GHz is supported for a given
virtual interface. However, in a multi-radio wiphy (e.g., one that has
both lower bands and 6 GHz combined), the wiphy advertises support for
all bands. As a result, the 6 GHz Band Capabilities element is incorrectly
included in mesh beacon and station's association request frames of
interfaces operating in lower bands, without verifying whether the
interface is actually operating in a 6 GHz channel.
Fix this by verifying if the interface operates on 6 GHz channel
before adding the element. Note that this check cannot be placed
directly in ieee80211_put_he_6ghz_cap() as the same function is used to
add probe request elements while initiating scan in which case the
interface may not be operating in any band's channel.
Call the dedicated v4l2_disable_ioctl helper instead of manually
checking whether the current context is an encoder for the selection
api ioctls.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .querystd callback should not program the device with the detected
standard, it should only report the standard to user-space. User-space
may then use .s_std to set the standard, if it wants to use it.
All that is required of .querystd is to setup the auto detection of
standards and report its findings.
While at it add some documentation on why this can't happen while
streaming and improve the error handling using a scoped guard.
The .set_fmt callback should not write the new format directly do the
device, it should only store it and have it applied by .s_stream.
The .s_stream callback already calls adv7180_set_field_mode() so it's
safe to remove programming of the device and just store the format and
have .s_stream apply it.
The adv7180_set_power() utilizes adv7180_write() which in turn requires
the state mutex to be held, take it before calling adv7180_set_power()
to avoid tripping a lockdep_assert_held().
An exchange with a NFC target must complete within NCI_DATA_TIMEOUT.
A delay of 700 ms is not sufficient for cryptographic operations on smart
cards. CardOS 6.0 may need up to 1.3 seconds to perform 256-bit ECDH
or 3072-bit RSA. To prevent brute-force attacks, passports and similar
documents introduce even longer delays into access control protocols
(BAC/PACE).
The timeout should be higher, but not too much. The expiration allows
us to detect that a NFC target has disappeared.
Signed-off-by: Juraj Šarinay <juraj@sarinay.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://patch.msgid.link/20250902113630.62393-1-juraj@sarinay.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While updating the binary min-len implementation, I noticed that
the only user, should AFAICT be using exact-len instead.
In net/ipv4/fou_core.c FOU_ATTR_LOCAL_V6 and FOU_ATTR_PEER_V6
are only used for singular IPv6 addresses, and there are AFAICT
no known implementations trying to send more, it therefore
appears safe to change it to an exact-len policy.
This patch therefore changes the local-v6/peer-v6 attributes to
use an exact-len check, instead of a min-len check.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Link: https://patch.msgid.link/20250902154640.759815-2-ast@fiberby.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, during locating the CIVD section, the ixgbe driver loops
over the OROM area and at each iteration reads only OROM-datastruct-size
amount of data. This results in many small reads and is inefficient.
Optimize this by reading the entire OROM bank into memory once before
entering the loop. This significantly reduces the probing time.
Without this patch probing time may exceed over 25s, whereas with this
patch applied average time of probe is not greater than 5s.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, having a valid panel_id match is required to use the quirk
system. For certain devices, we know that all SKUs need a certain quirk.
Therefore, allow not specifying ident by only checking for a match
if panel_id is non-zero.
Tested-by: Philip Müller <philm@manjaro.org> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev> Link: https://lore.kernel.org/r/20250829145541.512671-2-lkml@antheas.dev Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
WA 22021007897 should also be applied to Graphics Versions 30.00, 30.01
and 30.03. To make it simple, simply use the range [3000, 3003] that
should be ok as there isn't a 3002 and if it's added, the WA list would
need to be revisited anyway.
Cc: Matt Atwood <matthew.s.atwood@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Tangudu Tilak Tirumalesh <tilak.tirumalesh.tangudu@intel.com> Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com> Link: https://lore.kernel.org/r/20250827-wa-22021007897-v1-1-96922eb52af4@intel.com Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ipv6_rpl_srh_rcv() we use min(net->ipv6.devconf_all->rpl_seg_enabled,
idev->cnf.rpl_seg_enabled) is intended to return 0 when either value is
zero, but if one of the values is negative it will in fact return non-zero.
rss_ctx.test_rss_key_indir implicitly expects at least 5 queues,
as it checks that the traffic on first 2 queues is lower than
the remaining queues when we use all queues. Special case fewer
queues.
We want to mount beneath the given location. For that operation to
make sense, location must be the root of some mount that has something
under it. Currently we let it proceed if those requirements are not met,
with rather meaningless results, and have that bogosity caught further
down the road; let's fail early instead - do_lock_mount() doesn't make
sense unless those conditions hold, and checking them there makes
things simpler.
Reviewed-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SMC can take an excessive amount of time to process some
messages under some conditions.
Background:
Sending a message to the SMC works by writing the message into
the mmSMC_MESSAGE_0 register and its optional parameter into
the mmSMC_SCRATCH0, and then polling mmSMC_RESP_0. Previously
the timeout was AMDGPU_MAX_USEC_TIMEOUT, ie. 100 ms.
Increase the timeout to 200 ms for all messages and to 1 sec for
a few messages which I've observed to be especially slow:
PPSMC_MSG_NoForcedLevel
PPSMC_MSG_SetEnabledLevels
PPSMC_MSG_SetForcedLevels
PPSMC_MSG_DisableULV
PPSMC_MSG_SwitchToSwState
This fixes the following problems on Tahiti when switching
from a lower clock power state to a higher clock state, such
as when DC turns on a display which was previously turned off.
* si_restrict_performance_levels_before_switch would fail
(if the user previously forced high clocks using sysfs)
* si_set_sw_state would fail (always)
It turns out that both of those failures were SMC timeouts and
that the SMC actually didn't fail or hang, just needs more time
to process those.
Add a warning when there is an SMC timeout to make it easier to
identify this type of problem in the future.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kfd CRIU checkpoint ioctl would return an error if trying
to checkpoint a process with no kfd buffer objects.
This is a normal case and should not be an error.
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: David Francis <David.Francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver unconditionally saves current state on first init in
dsi_pll_7nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_7nm_pll_restore_state().
Restoring calls dsi_pll_7nm_vco_set_rate() with
pll_7nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
According to Hardware Programming Guide for DSI PHY, the retime buffer
resync should be done after PLL clock users (byte_clk and intf_byte_clk)
are enabled. Downstream also does it as part of configuring the PLL.
Driver was only turning off the resync FIFO buffer, but never bringing it
on again.
DMA Engine has support for the callback_result which provides
the status of the request and the residue. This helps in
determining the correct status of the request and in
efficient resource management of the request.
The 'callback_result' method is preferred over the deprecated
'callback' method.
This patch modifies the type of setup_xref from void to int and handles
errors since the function can fail.
`setup_xref` now returns the (eventual) error from
`dmae_set_dmars`|`dmae_set_chcr`, while `shdma_tx_submit` handles the
result, removing the chunks from the queue and marking PM as idle in
case of an error.
When a buffer object (BO) is allocated with the XE_BO_FLAG_GGTT_INVALIDATE
flag, the driver initiates TLB invalidation requests via the CTB mechanism
while releasing the BO. However a premature release of the CTB BO can lead
to system crashes, as observed in:
Introduce a devm-managed release action during xe_guc_ct_init() and
xe_guc_ct_init_post_hwconfig() to ensure proper CTB disablement before
resource deallocation, preventing the use-after-free scenario.
Signed-off-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Summers Stuart <stuart.summers@intel.com> Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Link: https://lore.kernel.org/r/20250901072541.31461-1-satyanarayana.k.v.p@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Networking drivers implementing PTP clocks and kernel socket code
handling hardware timestamps use the 64-bit signed ktime_t type counting
nanoseconds. When a PTP clock reaches the maximum value in year 2262,
the timestamps returned to applications will overflow into year 1667.
The same thing happens when injecting a large offset with
clock_adjtime(ADJ_SETOFFSET).
The commit 7a8e61f84786 ("timekeeping: Force upper bound for setting
CLOCK_REALTIME") limited the maximum accepted value setting the system
clock to 30 years before the maximum representable value (i.e. year
2232) to avoid the overflow, assuming the system will not run for more
than 30 years.
Enforce the same limit for PTP clocks. Don't allow negative values and
values closer than 30 years to the maximum value. Drivers may implement
an even lower limit if the hardware registers cannot represent the whole
interval between years 1970 and 2262 in the required resolution.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <jstultz@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250828103300.1387025-1-mlichvar@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
trans_pcie::fh_mask and hw_mask indicates what are the interrupts are
currently enabled (unmasked).
When we disable all interrupts, those should be set to 0, so if, for
some reason, we get an interrupt even though it was disabled, we will
know to ignore.
The current implementation unconditionally calls
mxc_isi_video_cleanup_streaming() in mxc_isi_video_release(). This can
lead to situations where any release call (like from a simple
"v4l2-ctl -l") may release a currently streaming queue when called on
such a device.
This is reproducible on an i.MX8MP board by streaming from an ISI
capture device using gstreamer:
Address this issue by moving the streaming preparation and cleanup to
the vb2 .prepare_streaming() and .unprepare_streaming() operations. This
also simplifies the driver by allowing direct usage of the
vb2_ioctl_streamon() and vb2_ioctl_streamoff() helpers, and removal of
the manual cleanup from mxc_isi_video_release().
Link: https://lore.kernel.org/r/20250813212451.22140-2-laurent.pinchart@ideasonboard.com Signed-off-by: Richard Leitner <richard.leitner@linux.dev> Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Richard Leitner <richard.leitner@linux.dev> # i.MX8MP Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The imx-mipi-csis driver sets the rate of the wrap clock to the value
specified in the device tree's "clock-frequency" property, and defaults
to 166 MHz otherwise. This is a historical mistake, as clock rate
selection should have been left to the assigned-clock-rates property.
Honouring the clock-frequency property can't be removed without breaking
backwards compatibility, and the corresponding code isn't very
intrusive. The 166 MHz default, on the other hand, prevents
configuration of the clock rate through assigned-clock-rates, as the
driver immediately overwrites the rate. This behaviour is confusing and
has cost debugging time.
There is little value in a 166 MHz default. All mainline device tree
sources that enable the CSIS specify a clock-frequency explicitly, and
the default wrap clock configuration on supported platforms is at least
as high as 166 MHz. Drop the default, and only set the clock rate
manually when the clock-frequency property is specified.
On FSD platform, gating the reference clock (ref_clk) and putting the
UFS device in reset by asserting the reset signal during UFS suspend,
improves the power savings and ensures the PHY is fully turned off.
These operations are added as FSD specific suspend hook to avoid
unintended side effects on other SoCs supported by this driver.
Co-developed-by: Nimesh Sati <nimesh.sati@samsung.com> Signed-off-by: Nimesh Sati <nimesh.sati@samsung.com> Signed-off-by: Bharat Uppal <bharat.uppal@samsung.com> Link: https://lore.kernel.org/r/20250821053923.69411-1-bharat.uppal@samsung.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make the "mclk" clock optional in the ad7124 driver. The MCLK is an
internal counter on the ADC, so it is not something that should be
coming from the devicetree. However, existing users may be using this
to essentially select the power mode of the ADC from the devicetree.
In order to not break those users, we have to keep the existing "mclk"
handling, but now it is optional.
Now, when the "mclk" clock is omitted from the devicetree, the driver
will default to the full power mode. Support for an external clock
and dynamic power mode switching can be added later if needed.
As noted in the kernel documentation [1], open-coded multiplication in
allocator arguments is discouraged because it can lead to integer overflow.
Use kcalloc() to gain built-in overflow protection, making memory
allocation safer when calculating allocation size compared to explicit
multiplication. Similarly, use size_add() instead of explicit addition
for 'uobj_chunk_num + sobj_chunk_num'.
Introduce support for standard MII ioctl operations in the LAN865x
Ethernet driver by implementing the .ndo_eth_ioctl callback. This allows
PHY-related ioctl commands to be handled via phy_do_ioctl_running() and
enables support for ethtool and other user-space tools that rely on ioctl
interface to perform PHY register access using commands like SIOCGMIIREG
and SIOCSMIIREG.
This feature enables improved diagnostics and PHY configuration
capabilities from userspace.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: stp@e100bb0 (lantiq,gpio-stp-xway): $nodename:0: 'stp@e100bb0' does not match '^gpio@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bindig requires a node name matching ‘^gpio@[0-9a-f]+$’. This patch
changes the clock name from “stp” to “gpio”.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: pci@e105400 (lantiq,pci-xway): 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/pci/pci-bus-common.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: / (lantiq,xway): 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warnings:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpu@0 (mips,mips24Kc): 'reg' is a required property
from schema $id: http://devicetree.org/schemas/mips/cpus.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Update the legacy (non-DC) display code to respect the maximum
pixel clock for HDMI and DVI-D. Reject modes that would require
a higher pixel clock than can be supported.
Also update the maximum supported HDMI clock value depending on
the ASIC type.
For reference, see the DC code:
check max_hdmi_pixel_clock in dce*_resource.c
v2:
Fix maximum clocks for DVI-D and DVI/HDMI adapters.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why & How]
Previously, when calculating dto phase, we would incorrectly fail when phase
<=0 without additionally checking for the integer value. This meant that
calculations would incorrectly fail when the desired pixel clock was an exact
multiple of the reference clock.
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Clay King <clayking@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
-Pipe splitting allows for clocks to be reduced, but when using TMDS 420,
reduced clocks lead to missed clocks cycles on clock resyncing
[How]
-Impose a minimum clock when using TMDS 420
Reviewed-by: Chris Park <chris.park@amd.com> Signed-off-by: Relja Vojvodic <rvojvodi@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can have modules in path which can change the number of channels and in
this case the BE params needs to be adjusted to configure the DAI according
to the copier configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Message-ID: <20250829105305.31818-2-peter.ujfalusi@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compare the whole v4l2_bt_timings struct, not just the width/height when
setting new timings. Timings with the same resolution and different
pixelclock can now be properly set.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 0d6ccfe6b319 ("selftests: drv-net: rss_ctx: check for all-zero keys")
added a skip exception if NIC has fewer than 3 queues enabled,
but it's just constructing the object, it's not actually rising
this exception.
Before:
# Exception| net.lib.py.utils.CmdExitFailure: Command failed: ethtool -X enp1s0 equal 3 hkey d1:cc:77:47:9d:ea:15:f2:b9:6c:ef:68:62:c0:45:d5:b0:99:7d:cf:29:53:40:06:3d:8e:b9:bc:d4:70:89:b8:8d:59:04:ea:a9:c2:21:b3:55:b8:ab:6b:d9:48:b4:bd:4c:ff:a5:f0:a8:c2
not ok 1 rss_ctx.test_rss_key_indir
After:
ok 1 rss_ctx.test_rss_key_indir # SKIP Device has fewer than 3 queues (or doesn't support queue stats)
Filter out modes that have a clock rate greater than the max core clock
rate when adjusted for the perf clock factor
This is especially important for chipsets such as QCS615 that have lower
limits for the MDP max core clock.
Since the core CRTC clock is at least the mode clock (adjusted for the
perf clock factor) [1], the modes supported by the driver should be less
than the max core clock rate.
A partitioned system configured with only one package and one compute
die, warning will be generated for duplicate sysfs entry. This typically
occurs during the platform bring-up phase.
Partitioned systems expose dies, equivalent to TPMI compute domains,
through the CPUID. Each partitioned system must contains at least one
compute die per partition, resulting in a minimum of two dies per
package. Hence the function topology_max_dies_per_package() returns at
least two, and the condition "topology_max_dies_per_package() > 1"
prevents the creation of a root domain.
In this case topology_max_dies_per_package() will return 1 and root
domain will be created for partition 0 and a duplicate sysfs warning
for partition 1 as both partitions have same package ID.
To address this also check for non zero partition in addition to
topology_max_dies_per_package() > 1.
When beacon loss happens or the RSSI drops, trigger MLO scan only
if not in EMLSR. The link switch was meant to be done when we are
not in EMLSR and we can try to switch to a better link.
If in EMLSR, we exit first and then trigger MLO scan.
Upon experiencing a PCI error, fbnic reset the device to recover from
the failure. Reset the hardware stats as part of the device reset to
ensure accurate stats reporting.
Note that the reset is not really resetting the aggregate value to 0,
which may result in a spike for a system collecting deltas in stats.
Rather, the reset re-latches the current value as previous, in case HW
got reset.
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250825200206.2357713-3-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes an issue where two different flows on the same RXq
produce the same hash resulting in continuous flow overwrites.
Flow #1: A packet for Flow #1 comes in, kernel calls the steering
function. The driver gives back a filter id. The kernel saves
this filter id in the selected slot. Later, the driver's
service task checks if any filters have expired and then
installs the rule for Flow #1.
Flow #2: A packet for Flow #2 comes in. It goes through the same steps.
But this time, the chosen slot is being used by Flow #1. The
driver gives a new filter id and the kernel saves it in the
same slot. When the driver's service task runs, it runs through
all the flows, checks if Flow #1 should be expired, the kernel
returns True as the slot has a different filter id, and then
the driver installs the rule for Flow #2.
Flow #1: Another packet for Flow #1 comes in. The same thing repeats.
The slot is overwritten with a new filter id for Flow #1.
This causes a repeated cycle of flow programming for missed packets,
wasting CPU cycles while not improving performance. This problem happens
at higher rates when the RPS table is small, but tests show it still
happens even with 12,000 connections and an RPS size of 16K per queue
(global table size = 144x16K = 64K).
This patch prevents overwriting an rps_dev_flow entry if it is active.
The intention is that it is better to do aRFS for the first flow instead
of hurting all flows on the same hash. Without this, two (or more) flows
on one RX queue with the same hash can keep overwriting each other. This
causes the driver to reprogram the flow repeatedly.
Changes:
1. Add a new 'hash' field to struct rps_dev_flow.
2. Add rps_flow_is_active(): a helper function to check if a flow is
active or not, extracted from rps_may_expire_flow(). It is further
simplified as per reviewer feedback.
3. In set_rps_cpu():
- Avoid overwriting by programming a new filter if:
- The slot is not in use, or
- The slot is in use but the flow is not active, or
- The slot has an active flow with the same hash, but target CPU
differs.
- Save the hash in the rps_dev_flow entry.
4. rps_may_expire_flow(): Use earlier extracted rps_flow_is_active().
Testing & results:
- Driver: ice (E810 NIC), Kernel: net-next
- #CPUs = #RXq = 144 (1:1)
- Number of flows: 12K
- Eight RPS settings from 256 to 32768. Though RPS=256 is not ideal,
it is still sufficient to cover 12K flows (256*144 rx-queues = 64K
global table slots)
- Global Table Size = 144 * RPS (effectively equal to 256 * RPS)
- Each RPS test duration = 8 mins (org code) + 8 mins (new code).
- Metrics captured on client
Legend for following tables:
Steer-C: #times ndo_rx_flow_steer() was Called by set_rps_cpu()
Steer-L: #times ice_arfs_flow_steer() Looped over aRFS entries
Add: #times driver actually programmed aRFS (ice_arfs_build_entry())
Del: #times driver deleted the flow (ice_arfs_del_flow_rules())
Units: K = 1,000 times, M = 1 million times
Some observations:
1. Overall Latency improved: (1790.19-1634.94)/1790.19*100 = 8.67%
2. Overall CPU increased: (777.32-751.49)/751.45*100 = 3.44%
3. Flow Management (add/delete) remained almost constant at ~11K
compared to values in millions.
Add a new _fini() routine on the GT TLB invalidation
side to handle this worker cleanup on driver teardown.
v2: Move the TLB teardown to the gt fini() routine called during
gt_init rather than in gt_alloc. This way the GT structure stays
alive for while we reset the TLB state.
[WHY&HOW]
The sink max slice width limitation should be considered for DSC, but
was removed in "refactor DSC cap calculations".
This patch adds it back and takes the valid minimum between the sink and
source.
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When KFD asks CP to preempt queues, other than preempt CP queues, CP
also requests SDMA to preempt SDMA queues with UNMAP_LATENCY timeout.
Currently queue_preemption_timeout_ms is 9000 ms by default but can be
configured via module parameter. KFD_UNMAP_LATENCY_MS is hard coded as
4000 ms though. This patch ties KFD_UNMAP_LATENCY_MS to
queue_preemption_timeout_ms so in a slow system such as emulator, both
CP and SDMA slowness are taken into account.
Signed-off-by: Amber Lin <Amber.Lin@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
For the HW cursor, its current position in the pipe_ctx->stream struct is
not affected by the 180 rotation, i. e. the top left corner is still at
0,0. However, the DPP & HUBP set_cursor_position functions require rotated
position.
The current approach is hard-coded for ODM 2:1, thus it's failing for
ODM 4:1, resulting in a double cursor.
[How]
Instead of calculating the new cursor position relatively to the
viewports, we calculate it using a viewavable clip_rect of each plane.
The clip_rects are first offset and scaled to the same space as the
src_rect, i. e. Stream space -> Plane space.
In case of a pipe split, which divides the plane into 2 or more viewports,
the clip_rect is the union of all the viewports of the given plane.
With the assumption that the viewports in HUBP's set_cursor_position are
in the Plane space as well, it should produce a correct cursor position
for any number of pipe splits.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Signed-off-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When it only allocates vram without va, which is 0, and a
SVM range allocated stays in this range, the vram allocation
returns failure. It should be skipped for this case from
SVM usage check.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Ce Sun <cesun102@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
By polling, poll ACA bank count to ensure that valid
ACA bank reg info can be obtained
v2: add corresponding delay before send msg to SMU to query mca bank info
(Stanley)
v3: the loop cannot exit. (Thomas)
v4: remove amdgpu_aca_clear_bank_count. (Kevin)
v5: continuously inject ce. If a creation interruption
occurs at this time, bank reg info will be lost. (Thomas)
v5: each cycle is delayed by 100ms. (Tao)
Signed-off-by: Ce Sun <cesun102@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pci_endpoint_test tests the 32-bit MSI range. However, the device might
not have all vectors configured. For example, if msi_interrupts is 8 in the
ep function space or if the MSI Multiple Message Capable value is
configured as 4 (maximum 16 vectors).
In this case, do not attempt to run the test to avoid timeouts and directly
return the error value.
This patch ensures the gt will be awake for the entire duration
of the resume sequences until GuCRC takes over and GT-C6 gets
re-enabled.
Before suspending GT-C6 is kept enabled, but upon resume, GuCRC
is not yet alive to properly control the exits and some cases of
instability and corruption related to GT-C6 can be observed.
The original commit be2ff42c5d6e ("fuse: Use hash table to link
processing request") converted fuse_pqueue->processing to a hash table,
but virtio_fs_enqueue_req() was not updated to use it correctly.
So use fuse_pqueue->processing as a hash table, this make the code
more coherent
Co-developed-by: Fushuai Wang <wangfushuai@baidu.com> Signed-off-by: Fushuai Wang <wangfushuai@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The test currently modifies the HDS settings and doesn't restore them.
This may cause subsequent tests to fail (or pass when they should not).
Add defer()ed reset handling.
fixed_phy_register() creates and registers the phy_device. To be
symmetric, we should not only unregister, but also free the phy_device
in fixed_phy_unregister(). This allows to simplify code in users.
Note wrt of_phy_deregister_fixed_link():
put_device(&phydev->mdio.dev) and phy_device_free(phydev) are identical.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/ad8dda9a-10ed-4060-916b-3f13bdbb899d@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 9ab440a9d042 ("drm/xe/ptl: L3bank mask is not
available on the media GT") added a workaround to ignore
the fuse register that L3 bank availability as it did not
contain valid values. Same is true for WCL therefore extend
the workaround to cover it.
Device can be unbound, so driver must also release memory for the wakeup
source. Do not use devm interface, because it would change the order of
cleanup.
Eliminate the use of static variables within the log pull implementation
to resolve a race condition and prevent data gaps when pulling logs from
multiple controllers in parallel, ensuring each operation is properly
isolated.
Firmware can enter a transient fault while creating operational queues.
The driver fails the load immediately.
Add a retry loop that checks controller status and history bit after
queue creation. If either indicates a fault, retry init up to a set
limit before failing.
When Wi-Fi is scanning at 2.4GHz, PTA will abort almost all the BT request.
Once the Wi-Fi slot stay too long, BT audio device can not get enough data,
audio glitch will happened. This patch limit 2.4Ghz Wi-Fi slot to 80ms
while Wi-Fi is scanning to avoid audio glitch.
During enclosure reboot or expander reset, firmware may report a link
speed of 0 in "Device Add" events while the link is still coming up.
The driver drops such devices, leaving them missing even after the link
recovers.
Fix this by treating link speed 0 as 1.5 Gbps during device addition so
the device is exposed to the OS. The actual link speed will be updated
later when link-up events arrive.
Currently, ip_extract_route_hint uses RTN_BROADCAST to decide
whether to use the route dst hint mechanism.
This check is too strict, as it prevents directed broadcast
routes from using the hint, resulting in poor performance
during bursts of directed broadcast traffic.
Fix this in ip_extract_route_hint and modify ip_route_use_hint
to preserve the intended behaviour.
Module aliases are used by userspace to identify the correct module to
load for a detected hardware. The currently supported RPMSG device IDs for
this module include "rpmsg-raw", but the module alias is "rpmsg_chrdev".
Use the helper macro MODULE_DEVICE_TABLE(rpmsg) to export the correct
supported IDs. And while here, to keep backwards compatibility we also add
the other ID "rpmsg_chrdev" so that it is also still exported as an alias.
This has the side benefit of adding support for some legacy firmware
which still uses the original "rpmsg_chrdev" ID. This was the ID used for
this driver before it was upstreamed (as reflected by the module alias).
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Hari Nagalla <hnagalla@ti.com> Tested-by: Hari Nagalla <hnagalla@ti.com> Link: https://lore.kernel.org/r/20250619205722.133827-1-afd@ti.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
