This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: rmanohar@qca.qualcomm.com Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Cedarview.
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Poulsbo.
When booted in legacy mode device_init_wakeup() gets called by
drivers/mfd/twl-core.c when the children are initialized. However, when
booted using device tree, the children are created with
of_platform_populate() instead add_children().
This means that the RTC driver will not have device_init_wakeup() set,
and we need to call it from the driver probe like RTC drivers typically
do.
Without this we cannot test PM wake-up events on omaps for cases where
there may not be any physical wake-up event.
Signed-off-by: Tony Lindgren <tony@atomide.com> Reported-by: Kevin Hilman <khilman@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whether rbd_client_create() successfully creates a new client or
not, it takes responsibility for getting the ceph_opts structure
it's passed destroyed. If successful, the structure becomes
associated with the created client; if not, rbd_client_create()
will destroy it.
Previously, rbd_get_client() would call ceph_destroy_options()
if rbd_get_client() failed, and that meant it got called twice.
That led freeing various pointers more than once, which is never a
good idea.
This resolves:
http://tracker.ceph.com/issues/4559
Reported-by: Dan van der Ster <dan@vanderster.com> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Josh Durgin <josh.durgin@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ceph's encode_caps_cb() worked hard to not call __page_cache_alloc()
while holding a lock, but it's spoiled because ceph_pagelist_addpage()
always calls kmap(), which might sleep. Here's the result:
In his review, Alex Elder mentioned that he hadn't checked that
num_fcntl_locks and num_flock_locks were properly decoded on the
server side, from a le32 over-the-wire type to a cpu type.
I checked, and AFAICS it is done; those interested can consult
Locker::_do_cap_update()
in src/mds/Locker.cc and src/include/encoding.h in the Ceph server
code (git://github.com/ceph/ceph).
I also checked the server side for flock_len decoding, and I believe
that also happens correctly, by virtue of having been declared
__le32 in struct ceph_mds_cap_reconnect, in src/include/ceph_fs.h.
Signed-off-by: Jim Schutt <jaschut@sandia.gov> Reviewed-by: Alex Elder <elder@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An osd client has a red-black tree describing its osds, and
occasionally we would get crashes due to one of these trees tree
becoming corrupt somehow.
The problem turned out to be that reset_changed_osds() was being
called without protection of the osd client request mutex. That
function would call __reset_osd() for any osd that had changed, and
__reset_osd() would call __remove_osd() for any osd with no
outstanding requests, and finally __remove_osd() would remove the
corresponding entry from the red-black tree. Thus, the tree was
getting modified without having any lock protection, and was
vulnerable to problems due to concurrent updates.
This appears to be the only osd tree updating path that has this
problem. It can be fairly easily fixed by moving the call up
a few lines, to just before the request mutex gets dropped
in kick_requests().
This resolves:
http://tracker.ceph.com/issues/5043
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the introduction of ACPI scan handlers, ACPI device objects
with an ACPI scan handler attached to them must not be bound to
by ACPI drivers any more. Unfortunately, however, the ACPI video
driver attempts to do just that if there is a _ROM ACPI control
method defined under a device object with an ACPI scan handler.
Prevent that from happening by making the video driver's "add"
routine check if the device object already has an ACPI scan handler
attached to it and return an error code in that case.
That is not sufficient, though, because acpi_bus_driver_init() would
then clear the device object's driver_data that may be set by its
scan handler, so for the fix to work acpi_bus_driver_init() has to be
modified to leave driver_data as is on errors.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091 Bisected-and-tested-by: Dmitry S. Demin <dmitryy.demin@gmail.com> Reported-and-tested-by: Jason Cassell <bluesloth600@gmail.com> Tracked-down-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Sun, 9 Jun 2013 20:09:24 +0000 (21:09 +0100)]
s390: Add pgste to ptep_modify_prot_start()
Commit 52f36be0f4e2 's390/pgtable: Fix check for pgste/storage key
handling', which was commit b56433cb782d upstream, added a use of
pgste to ptep_modify_prot_start(), but this variable does not exist.
In mainline, pgste was added by commit d3383632d4e8 's390/mm: add pte
invalidation notifier for kvm' and initialised to the return value of
pgste_get_lock(ptep). Initialise it similarly here.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31ade30692dc9680bfc95700d794818fa3f754ac, timekeeping_init()
checks for presence of persistent clock by attempting to read a non-zero
time value. This is an issue on platforms where persistent_clock (instead
is implemented as a free-running counter (instead of an RTC) starting
from zero on each boot and running during suspend. Examples are some ARM
platforms (e.g. PandaBoard).
An attempt to read such a clock during timekeeping_init() may return zero
value and falsely declare persistent clock as missing. Additionally, in
the above case suspend times may be accounted twice (once from
timekeeping_resume() and once from rtc_resume()), resulting in a gradual
drift of system time.
This patch does a run-time correction of the issue by doing the same check
during timekeeping_suspend().
A better long-term solution would have to return error when trying to read
non-existing clock and zero when trying to read an uninitialized clock, but
that would require changing all persistent_clock implementations.
This patch addresses the immediate breakage, for now.
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Feng Tang <feng.tang@intel.com>
[jstultz: Tweaked commit message and subject] Signed-off-by: John Stultz <john.stultz@linaro.org>
[zoran.markovic@linaro.org: reworked patch to fit 3.9-stable.] Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xen_play_dead is an undead function. When the vCPU is told to
offline it ends up calling xen_play_dead wherin it calls the
VCPUOP_down hypercall which offlines the vCPU. However, when the
vCPU is onlined back, it resumes execution right after
VCPUOP_down hypercall.
That was OK (albeit the API for play_dead assumes that the CPU
stays dead and never returns) but with commit 4b0c0f294
(tick: Cleanup NOHZ per cpu data on cpu down) that is no longer safe
as said commit resets the ts->inidle which at the start of the
cpu_idle loop was set.
b/c ts_inidle is set to zero. Thomas suggested that we just add a workaround
to call tick_nohz_idle_enter before returning from xen_play_dead() - and
that is what this patch does and fixes the issue.
We also add the stable part b/c git commit 4b0c0f294 is on the stable
tree.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The stop machine logic can lock up if all but one of the migration
threads make it through the disable-irq step and the one remaining
thread gets stuck in __do_softirq. The reason __do_softirq can hang is
that it has a bail-out based on jiffies timeout, but in the lockup case,
jiffies itself is not incremented.
To work around this, re-add the max_restart counter in __do_irq and stop
processing irqs after 10 restarts.
Thanks to Tejun Heo and Rusty Russell and others for helping me track
this down.
This was introduced in 3.9 by commit c10d73671ad3 ("softirq: reduce
latencies").
It may be worth looking into ath9k to see if it has issues with its irq
handler at a later date.
The hang stack traces look something like this:
------------[ cut here ]------------
WARNING: at kernel/watchdog.c:245 watchdog_overflow_callback+0x9c/0xa7()
Watchdog detected hard LOCKUP on cpu 2
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
Pid: 23, comm: migration/2 Tainted: G C 3.9.4+ #11
Call Trace:
<NMI> warn_slowpath_common+0x85/0x9f
warn_slowpath_fmt+0x46/0x48
watchdog_overflow_callback+0x9c/0xa7
__perf_event_overflow+0x137/0x1cb
perf_event_overflow+0x14/0x16
intel_pmu_handle_irq+0x2dc/0x359
perf_event_nmi_handler+0x19/0x1b
nmi_handle+0x7f/0xc2
do_nmi+0xbc/0x304
end_repeat_nmi+0x1e/0x2e
<<EOE>>
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
---[ end trace 4947dfa9b0a4cec3 ]---
BUG: soft lockup - CPU#1 stuck for 22s! [migration/1:17]
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
irq event stamp: 835637905
hardirqs last enabled at (835637904): __do_softirq+0x9f/0x257
hardirqs last disabled at (835637905): apic_timer_interrupt+0x6d/0x80
softirqs last enabled at (5654720): __do_softirq+0x1ff/0x257
softirqs last disabled at (5654725): irq_exit+0x5f/0xbb
CPU 1
Pid: 17, comm: migration/1 Tainted: G WC 3.9.4+ #11 To be filled by O.E.M. To be filled by O.E.M./To be filled by O.E.M.
RIP: tasklet_hi_action+0xf0/0xf0
Process migration/1
Call Trace:
<IRQ>
__do_softirq+0x117/0x257
irq_exit+0x5f/0xbb
smp_apic_timer_interrupt+0x8a/0x98
apic_timer_interrupt+0x72/0x80
<EOI>
printk+0x4d/0x4f
stop_machine_cpu_stop+0x22c/0x274
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Pekka Riikonen <priikone@iki.fi> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 263e1f9f ("USB:
io_ti: query hardware-buffer status in chars_in_buffer") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 6f602912 ("usb:
serial: ftdi_sio: Add missing chars_in_buffer function") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Currently the driver's assumed behavior for a modeset with an attached
FB is that the corresponding connector will be switched to DPMS ON mode
if it happened to be in DPMS OFF (or another power save mode). This
wasn't enforced though if only the FB changed, everything else (format,
connector etc.) remaining the same. In this case we only set the new FB
base and left the connector in the old power save mode.
Fix this by forcing a full modeset whenever there is an attached FB and
any affected connector is in a power save mode.
V_2: Run the test for encoders in power save mode outside the the
test for fb change: user space may have just disabled the encoders
but left everything else in place. Make sure the connector list is
not empty before running this test.
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On pseries machines the detection for max_bus_speed should be done
through an OpenFirmware property. This patch adds a function to perform
this detection and a hook to perform dynamic adding of the function only
for pseries. This is done by overwriting the weak
pcibios_root_bridge_prepare function which is called by
pci_create_root_bus().
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent commit e61133dda480062d221f09e4fc18f66763f8ecd0 added support
for a new firmware feature to force an adapter to use 32 bit MSIs.
However, this firmware is not available for all systems. The hack below
allows devices needing 32 bit MSIs to work on these systems as well.
It is careful to only enable this on Gen2 slots, which should limit
this to configurations where this hack is needed and tested to work.
[Small change to factor out the hack into a separate function -- BenH]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch implements a new PAPR change which allows
the OS to force the use of 32 bit MSIs, regardless of what
the PCI capabilities indicate. This is required for some
devices that advertise support for 64 bit MSIs but don't
actually support them.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a PCI quirk for VGA devices on Power to set the default VGA device.
Ensures a default VGA is always set if a graphics adapter is present,
even if firmware did not initialize it. If more than one graphics
adapter is present, ensure the one initialized by firmware is set
as the default VGA device. This ensures that X autoconfiguration
will work.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set dev->dev.type in alloc_pci_dev so that archs that have their own
versions of pci_setup_device get this set properly in order to ensure
things like the boot_vga sysfs parameter get created as expected.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By having a higher max resolution we can now set up a virtual
framebuffer that spans several monitors. 4096 should be ok since we're
gen 3 or higher and should be enough for most dual head setups.
we never allocate a TRB pool for physical endpoints
0 and 1 so trying to free it (a invalid TRB pool pointer)
will lead us in a warning while removing dwc3.ko module.
In order to fix the situation, all we have to do is skip
dwc3_free_trb_pool() for physical endpoints 0 and 1 just
as we while deleting endpoints from the endpoints list.
Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9f29ab11ddbf ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600. Tony says:
"It panics with the message:
Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel
[...] my problem comes from arch/ia64/hp/common/sba_iommu.c
where the code in sba_init() says:
acpi_bus_register_driver(&acpi_sba_ioc_driver);
if (!ioc_list) {
but because of this change we never managed to call ioc_init()
so ioc_list doesn't get set up, and we die."
Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
X can again get -EIO when it does not expect it. And even worse score
a SIGBUS when accessing gtt mmaps. The established ABI is that we
_only_ return an -EIO from execbuf - all other ioctls should just
work. And since the reset code moves all bos out of gpu domains and
clears out all the last_seqno/ring tracking there really shouldn't be
any reason for non-execbuf code to ever touch the hw and see an -EIO.
After some extensive discussions we've noticed that these spurios -EIO
are caused by i915_gem_wait_for_error:
That is easy to fix by returning 0 instead of -EIO, since grabbing the
dev->struct_mutex does not yet mean that we actually want to touch the
hw. And so there is no reason at all to fail with -EIO.
But that's not the entire since, since often (at least it's easily
googleable) dmesg indicates that the reset fails and we declare the
gpu wedged. Then, quite a bit later X wakes up with the "Timed out
waiting for the gpu reset to complete" DRM_ERROR message in
wait_for_errror and brings down the desktop with an -EIO/SIGBUS.
So clearly we're missing a wakeup somewhere, since the gpu reset just
doesn't take 10 seconds to complete. And indeed we're do handle the
terminally wedged state wrong.
Fix this all up.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Last year, a patch was made for the "HP t5740e Thin Client" (see
http://lists.freedesktop.org/archives/dri-devel/2012-May/023245.html).
This device reports an lvds panel, but does not really have one.
The predecessor of this device is the "hp t5740", which also does not have
an lvds panel. This patch will add the same quirk for this device.
Signed-off-by: Ben Mesman <ben@bnc.nl> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In intel_sdvo_get_lvds_modes() the wrong i2c adapter record is used
for DDC. Thus the code will always have to rely on a LVDS panel
mode supplied by VBT.
In most cases this succeeds, so this didn't get detected for quite
a while.
Signed-off-by: Egbert Eich <eich@suse.de> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about which commit likely introduced this issue.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When GPU acceleration is disabled, drm_vblank_cleanup() will free the
vblank-related data, such as vblank_refcount, vblank_inmodeset, etc.
But we found that drm_vblank_post_modeset() may be called after the
cleanup, which use vblank_refcount and vblank_inmodeset. And this will
cause a kernel panic.
Fix this by return immediately if dev->num_crtcs is zero. This is the
same thing that drm_vblank_pre_modeset() does.
This is a bug fix for some versions of g200se cards while doing
mode-setting.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Signed-off-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a system with both MAX1617 and JC42 sensors, JC42 sensors can be misdetected
as LM84. Strengthen detection sufficiently enough to avoid this misdetection.
Also improve detection for ADM1021.
Modeled after chip detection code in sensors-detect command.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Jean Delvare <khali@linux-fr.org> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When msync is called on a memory mapped file, that
data is not flushed to the disk.
In Linux, msync calls fsync for the file. For ecryptfs,
fsync just calls the lower level file system's fsync.
Changed the ecryptfs fsync code to call filemap_write_and_wait
before calling the lower level fsync.
Addresses the problem described in http://crbug.com/239536
commit 839db3d10a (cifs: fix up handling of prefixpath= option) changed
the code such that the vol->prepath no longer contained a leading
delimiter and then fixed up the places that accessed that field to
account for that change.
One spot in build_unc_path_to_root was missed however. When doing the
pointer addition on pos, that patch failed to account for the fact that
we had already incremented "pos" by one when adding the length of the
prepath. This caused a buffer overrun by one byte.
This patch fixes the problem by correcting the handling of "pos".
Reported-by: Marcus Moeller <marcus.moeller@gmx.ch> Reported-by: Ken Fallon <ken.fallon@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
The pm runtime reference counting of the driver is broken for the case
when there is more than one transfer queued, leading to the device being
runtime suspend while active. Fix it.
In commit bc09c21 "Fix finding overflowed PMC in interrupt" we added
a printk() to the PMU exception handler. Unfortunately that is not safe.
The problem is that the PMU exception may run even when interrupts are
soft disabled, aka NMI context. We do this so that we can profile parts
of the kernel that have interrupts soft-disabled.
But by calling printk() from the exception handler, we can potentially
deadlock in the printk code on logbuf_lock, eg:
When introducing support for DABRX in 4474ef0, we broke older 32-bit CPUs
that don't have that register.
Some CPUs have a DABR but not DABRX. Configuration are:
- No 32bit CPUs have DABRX but some have DABR.
- POWER4+ and below have the DABR but no DABRX.
- 970 and POWER5 and above have DABR and DABRX.
- POWER8 has DAWR, hence no DABRX.
This introduces CPU_FTR_DABRX and sets it on appropriate CPUs. We use
the top 64 bits for CPU FTR bits since only 64 bit CPUs have this.
Processors that don't have the DABRX will still work as they will fall
back to software filtering these breakpoints via perf_exclude_event().
Signed-off-by: Michael Neuling <mikey@neuling.org> Reported-by: "Gorelik, Jacob (335F)" <jacob.gorelik@jpl.nasa.gov> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RTAS token "ibm,get-config-addr-info" or ibm,get-config-addr-info2"
are used to retrieve the PE address according to PCI address, which
made up of domain/bus/slot/function. If we don't have those 2 tokens,
the domain/bus/slot/function would be used as the address for EEH
RTAS operations. Some older f/w might not have those 2 tokens and
that blocks the EEH functionality to be initialized. It was introduced
by commit e2af155c ("powerpc/eeh: pseries platform EEH initialization").
The patch skips the check on those 2 tokens so we can bring up EEH
functionality successfully. And domain/bus/slot/function will be
used as address for EEH RTAS operations.
Reported-by: Robert Knight <knight@princeton.edu> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Tested-by: Robert Knight <knight@princeton.edu> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__my_cpu_offset is non-volatile, since we want its value to be cached
when we access several per-cpu variables in a row with preemption
disabled. This means that we rely on preempt_{en,dis}able to hazard
with the operation via the barrier() macro, so that we can't end up
migrating CPUs without reloading the per-cpu offset.
Unfortunately, GCC doesn't treat a "memory" clobber on a non-volatile
asm block as a side-effect, and will happily re-order it before other
memory clobbers (including those in prempt_disable()) and cache the
value. This has been observed to break the cmpxchg logic in the slub
allocator, leading to livelock in kmem_cache_alloc in mainline kernels.
This patch adds a dummy memory input operand to __my_cpu_offset,
forcing it to be ordered with respect to the barrier() macro.
Reviewed-by: Nicolas Pitre <nico@linaro.org> Cc: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In August 2012, Matthew Gretton-Dann checked a change into binutils
labelled "Error on obsolete & warn on deprecated registers", apparently as
part of ARMv8 support. Apparently, this was supposed to emit the message
"Warning: This coprocessor register access is deprecated in ARMv8" when
using certain mcr/mrc instructions and building for ARMv8. Unfortunately,
the message that is actually emitted appears to be '(null)', which is
less helpful in comparison.
Even more unfortunately, this is biting us on every single kernel
build with a new gas, because arch/arm/boot/compressed/head.S and some
other files in that directory are built with -march=all since kernel
commit 80cec14a8 "[ARM] Add -march=all to assembly file build in
arch/arm/boot/compressed" back in v2.6.28.
This patch reverts Russell's nice solution and instead marks the head.S
file to be built for armv7-a, which fortunately lets us build all
instructions in that file without warnings even on the broken binutils.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Nicolas Pitre <nico@linaro.org> Cc: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating the DT based boards-ts219.c the none DT ts219-setup.c
was used as a template. This includes a lateinit() call to initialize
the PCIe bus. The code makes use of machine_is_ts219() which is never
true on DT, so a FIXME was added and the code left as is. This was
unproblematic until b73690c8f8b5d: "ARM: Kirkwood: Support basic
hotplug for PCI-E" which changes the way the PCIe bus is
initialized. The non-DT ts219-setup.c now crashes during boot. The
lateinit() call in the DT boards-ts219.c is being called,
machine_is_ts219() is true and so the PCIe is initialized a second
time.
This patch removes the useless, and now clearly dangerous, code from
boards-ts219.c, making ts219-setup.c work again.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VT1802 codec seems to reset EAPD of other pins in the hardware level,
and this was another reason of the silent headphone output on some
machines. As a workaround, introduce a new flag indicating to keep
the EPAD on to the generic parser, and set it in patch_via.c.
Some codec drivers (VIA codecs and some Realtek fixups) set the
automute and automic hooks after calling
snd_hda_gen_parse_auto_config(). In the current code, the hook
pointers are referred only in snd_hda_gen_parse_auto_config() and
passed to snd_hda_jack_detect_enable_callback(), thus changing the
hook values won't change the actually called callbacks properly.
This patch fixes this bug by setting the static functions as the
primary callback functions for the jack detection, and let them
calling the appropriate hooks dynamically.
VIA driver has a special suspend handling only for VT1802 to reduce
the pop noise. During the transition to the generic parser, the
behavior of snd_hda_set_pin_ctl() was also changed to modify the
cached values, too. And this caused a regression where the pin is
still cleared even after the resume (including the resume from power
save), resulting in the silent output.
The fix is simply to replace snd_hda_set_pin_ctl() with the explicit
call of snd_hda_codec_write() again.
Since the transition to the generic parser, the actual routes used
there don't match always with the assumed static paths in some
set_widgets_power_state callbacks. This results in the wrong power
setup in the end. As a temporary workaround, we need to disable the
calls together with the non-functional dynamic power control enum.
Check code and find this error is caused by misusing variable bluetooth_rfkill
where gps_rfkill should be.
Reported-and-tested-by: Iru Cai <mytbk920423@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=58401 Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b378549 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them. That turned out to break Toshiba P870-303,
however, so revert that code.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58201 Reported-and-tested-by: Jerome Cantenot <jerome.cantenot@gmail.com> Tracked-down-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the introduction of ACPI scan handlers, an ACPI device object
with an ACPI scan handler attached to it must not be bound to an ACPI
driver any more. Therefore it doesn't make sense to match those
ACPI device objects against a newly registered ACPI driver in
acpi_bus_match(), so make that function return 0 if the device
object passed to it has an ACPI scan handler attached.
This also addresses a regression related to a broken ACPI table in
the BIOS, where it has defined a _ROM method under the PCI root
bridge object. This causes the video module to treat that object
as a display controller device (since only display devices are
supposed to have a _ROM method defined according to the ACPI spec).
As a result, the ACPI video driver binds to the PCI root bridge
object and overwrites the previously assigned driver_data field of
it, causing subsequent calls to acpi_get_pci_dev() to fail.
[rjw: Subject and changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091 Reported-by: Jason Cassell <bluesloth600@gmail.com> Reported-and-bisected-by: Dmitry S. Demin <dmitryy.demin@gmail.com> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses kernel bug 56661. BIOS reports an incorrect
backlight value, causing the driver to switch off the backlight
completely during startup. This patch ignores the incorrect value from
BIOS.
References: https://bugzilla.kernel.org/show_bug.cgi?id=56661 Signed-off-by: Ash Willis <ashwillis@programmer.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On HP m4 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.
References: https://bugs.launchpad.net/bugs/1184501 Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4b31e774 (Always set P-state on initialization) fixed bug
#4634 and caused the driver to always set the target P-State at
least once since the initial P-State may not be the desired one.
Commit 5a1c0228 (cpufreq: Avoid calling cpufreq driver's target()
routine if target_freq == policy->cur) caused a regression in
this behavior.
This fixes the regression by setting policy->cur based on the CPU's
target frequency rather than the CPU's current reported frequency
(which may be different). This means that the P-State will be set
initially if the CPU's target frequency is different from the
governor's target frequency.
This fixes an issue where setting the default governor to
performance wouldn't correctly enable turbo mode on all cores.
Signed-off-by: Ross Lagerwall <rosslagerwall@gmail.com> Reviewed-by: Len Brown <len.brown@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d
(USB: EHCI: fix bug in scheduling periodic split transfers). The
commit was valid -- it fixed a real bug -- but the periodic scheduler
in ehci-hcd is in such bad shape (especially the part that handles
split transactions) that fixing one bug is very likely to cause
another to surface. That's what happened in this case; the result was
choppy and noisy playback on certain 24-bit audio devices.
The only real fix will be to rewrite this entire section of code. My
next project...
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1136110.
Thanks to Tim Richardson for extra testing and feedback, and to Joseph
Salisbury and Tyson Tan for tracking down the original source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Joseph Salisbury <joseph.salisbury@canonical.com> CC: Tim Richardson <tim@tim-richardson.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 214916f2e ("USB: visor: reimplement
using generic framework") which broke initialisation of Treo/Kyocera
devices that re-mapped bulk-in endpoints.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB audio driver spews an error message when probing Logitech HD
webcam c270:
ALSA mixer.c:1300 usb_audio: Warning! Unlikely big volume range (=6144), cval->res is probably wrong.
ALSA mixer.c:1304 usb_audio: [5] FU [Mic Capture Volume] ch = 1, val = 1536/7680/1
Obviously the device needs a fixed volume resolution (cval->res = 384)
like other Logitech devices.
Commit 927c9423dd5f2d1c0b93d5e694ab84b4a5559713 (ALSA: usb-audio: add
Edirol UM-3G support) used a wrong quirk type, which would make the
driver refuse to attach with the error message "MIDIStreaming interface
descriptor not found".
8e8a551 usb: musb: host: Handle highmem in PIO mode
when a URB is being handled it may happen that the static use_sg flag
was set by a previous URB with buffer in highmem. This leads to error
in handling the present URB.
f9a37be0f0 ("x86: Use PCI setup data") added support for using PCI ROM
images from setup_data. This used phys_to_virt(), which is not valid for
highmem addresses, and can cause a crash when booting a 32-bit kernel via
the EFI boot stub.
pcibios_add_device() assumes that the physical addresses stored in
setup_data are accessible via the direct kernel mapping, and that calling
phys_to_virt() is valid. This isn't guaranteed to be true on x86 where the
direct mapping range is much smaller than on x86-64.
Calling phys_to_virt() on a highmem address results in the following:
Some xHCI hosts contain a "redriver" from TI that silently drops port
status connect changes if the port slips into Compliance Mode. If the
port slips into compliance mode while the host is in D0, there will not
be a port status change event. If the port slips into compliance mode
while the host is in D3, the host will not send a PME. This includes
when the system is suspended (S3) or hibernated (S4).
If this happens when the system is in S3/S4, there is nothing software
can do. Other port status change events that would normally cause the
host to wake the system from S3/S4 may also be lost. This includes
remote wakeup, disconnects and connects on other ports, and overrcurrent
events. A decision was made to _NOT_ disable system suspend/hibernate
on these systems, since users are unlikely to enable wakeup from S3/S4
for the xHCI host.
Software can deal with this issue when the system is in S0. A work
around was put in to poll the port status registers for Compliance Mode.
The xHCI driver will continue to poll the registers while the host is
runtime suspended. Unfortunately, that means we can't allow the PCI
device to go into D3cold, because power will be removed from the host,
and the config space will read as all Fs.
Disable D3cold in the xHCI PCI runtime suspend function.
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
If for whatever reason we fall into fail path in xhci_mem_init()
before bw table gets initialized we may access the uninitialized lists
in xhci_mem_cleanup().
Check for bw table before traversing lists in cleanup routine.
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."
Reported-by: Sergey Dyasly <dserrg@gmail.com> Tested-by: Sergey Dyasly <dserrg@gmail.com> Signed-off-by: Vladimir Murzin <murzin.v@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that we fail on xhci_mem_init, just before doing
the INIT_LIST_HEAD, and calling xhci_mem_cleanup.
Problem is that, the list_for_each_entry_safe macro, assumes
list heads are initialized (not NULL), and dereferences their 'next'
pointer, causing a kernel panic if this is not yet initialized.
Let's protect from that by moving inits to the beginning.
Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP
Hardware) was a workaround for systems using the SN65LVPE502CP,
controller, but it introduced a bug in resume from hibernate.
The fix created a timer, comp_mode_recovery_timer, which is deleted from
a timer list when xhci_suspend() is called. However, the hibernate image,
including the timer list containing the comp_mode_recovery_timer, had
already been saved before the timer was deleted.
Upon resume from hibernate, the list containing the comp_mode_recovery_timer
is restored from the image saved to disk, and xhci_resume(), assuming that
the timer had been deleted by xhci_suspend(), makes a call to
compliance_mode_recoery_timer_init(), which creates a new instance of the
comp_mode_recovery_timer and attempts to place it into the same list in which
it is already active, thus corrupting the list during the list_add() call.
At this point, a call trace is emitted indicating the list corruption.
Soon afterward, the system locks up, the watchdog times out, and the
ensuing NMI crashes the system.
The problem did not occur when resuming from suspend. In suspend, the
image in RAM remains exactly as it was when xhci_suspend() deleted the
comp_mode_recovery_timer, so there is no problem when xhci_resume()
creates a new instance of this timer and places it in the still empty
list.
This patch avoids the problem by deleting the timer in xhci_resume()
when resuming from hibernate. Now xhci_resume() can safely make the
call to create a new instance of this timer, whether returning from
suspend or hibernate.
Thanks to Alan Stern for his help with understanding the problem.
[Sarah reworked this patch to cover the case where the xHCI restore
register operation fails, and (temp & STS_SRE) is true (and we re-init
the host, including re-init for the compliance mode), but hibernate is
false. The original patch would have caused list corruption in this
case.]
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Tony Camuso <tcamuso@redhat.com> Tested-by: Tony Camuso <tcamuso@redhat.com> Acked-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fatal_skb_slots is the threshold to determine whether a packet is
malicious.
XEN_NETBK_LEGACY_SLOTS_MAX is the maximum slots a valid packet can have at
this point. It is defined to be XEN_NETIF_NR_SLOTS_MIN because that's
guaranteed to be supported by all backends.
Suggested-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Thu, 23 May 2013 20:24:11 +0000 (22:24 +0200)]
mac80211_hwsim: remove P2P_DEVICE support
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Thu, 23 May 2013 20:24:31 +0000 (22:24 +0200)]
iwlwifi: mvm: remove P2P_DEVICE support
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it. For iwlmvm that implies disabling P2P completely
as it can't support P2P operation w/o P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum packet including header that can be handled by netfront / netback
wire format is 65535. Reduce gso_max_size accordingly.
Drop skb and print warning when skb->len > 65535. This can 1) save the effort
to send malformed packet to netback, 2) help spotting misconfiguration of
netfront in the future.
Signed-off-by: Wei Liu <wei.liu2@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tune xen_netbk_count_requests to not touch working array beyond limit, so that
we can make working array size constant.
Suggested-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
