If the firmware had set up a clock to source from PLLC, go along with
it. But if we're looking for a new parent, we don't want to switch it
to PLLC because the firmware will force PLLC (and thus the AXI bus
clock) to different frequencies during over-temp/under-voltage,
without notification to Linux.
On my system, this moves the Linux-enabled HDMI state machine and DSI1
escape clock over to plld_per from pllc_per. EMMC still ends up on
pllc_per, because the firmware had set it up to use that.
Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks") Acked-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
con3270 contains an optimisation that reduces the amount of data to be
transmitted to the 3270 terminal by putting a Repeat to Address (RA)
order into the data stream. The RA order itself takes up space, so
con3270 only uses it if there's enough space left in the line
buffer. Otherwise it just pads out the line manually.
For lines that were _just_ short enough that the RA order still fit in
the line buffer, the line was instead padded with an insufficient
amount of spaces. This was caused by examining the size of the
allocated line buffer rather than the length of the string to be
displayed.
For con3270_cline_end(), we just compare against the line length. For
con3270_update_string() however that isn't available anymore, so we
check whether the Repeat to Address order is present.
Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Tested-by: Jing Liu <liujbjl@linux.vnet.ibm.com> Tested-by: Yang Chen <bjcyang@linux.vnet.ibm.com> Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
con3270 contains an optimisation that reduces the amount of data to be
transmitted to the 3270 terminal by putting a Repeat to Address (RA)
order into the data stream. The RA order itself takes up space, so
con3270 only uses it if there's enough space left in the line
buffer. Otherwise it just pads out the line manually.
For lines too long to include the RA order, one byte was left
uninitialised. This was caused by an off-by-one bug in the loop that
pads out the line. Since the buffer is allocated from a common pool,
the single byte left uninitialised contained some previous buffer
content. Usually this was just a space or some character (which can
result in clutter but is otherwise harmless). Sometimes, however, it
was a Repeat to Address order, messing up the entire screen layout and
causing the display to send the entire buffer content on every
keystroke.
Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Reported-by: Liu Jing <liujbjl@linux.vnet.ibm.com> Tested-by: Jing Liu <liujbjl@linux.vnet.ibm.com> Tested-by: Yang Chen <bjcyang@linux.vnet.ibm.com> Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 9f3d6d7 chsc_get_channel_measurement_chars is called with
interrupts disabled during resume from hibernate. Since this function
used spin_unlock_irq, interrupts have been enabled accidentally. Fix
this by using the irqsave variant.
Since we can't guarantee the IRQ-enablement state for all (future/
external) callers, change the locking in related functions to prevent
similar bugs in the future.
Fixes: 9f3d6d7 ("s390/cio: update measurement characteristics") Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a view destruction command was present in the command stream, the
view was validated to avoid a device error. That caused excessive and
unnecessary validations of views, surfaces and mobs on view destruction.
Replace this with a new relocation type that patches the view
destruction command to a NOP if the view is not present in the device
after the execbuf validation sequence.
Also add checks for the member size of the vmw_res_relocation struct.
Fixes sporadic command submission errors on google-earth exit.
Reported-by: Brian Paul <brianp@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For every pfn aligned to minimum_order, dissolve_free_huge_pages() will
call dissolve_free_huge_page() which takes the hugetlb spinlock, even if
the page is not huge at all or a hugepage that is in-use.
Improve this by doing the PageHuge() and page_count() checks already in
dissolve_free_huge_pages() before calling dissolve_free_huge_page(). In
dissolve_free_huge_page(), when holding the spinlock, those checks need
to be revalidated.
Link: http://lkml.kernel.org/r/20160926172811.94033-4-gerald.schaefer@de.ibm.com Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Rui Teng <rui.teng@linux.vnet.ibm.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dissolve_free_huge_pages(), free hugepages will be dissolved without
making sure that there are enough of them left to satisfy hugepage
reservations.
Fix this by adding a return value to dissolve_free_huge_pages() and
checking h->free_huge_pages vs. h->resv_huge_pages. Note that this may
lead to the situation where dissolve_free_huge_page() returns an error
and all free hugepages that were dissolved before that error are lost,
while the memory block still cannot be set offline.
Fixes: c8721bbb ("mm: memory-hotplug: enable memory hotplug to handle hugepage") Link: http://lkml.kernel.org/r/20160926172811.94033-3-gerald.schaefer@de.ibm.com Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Rui Teng <rui.teng@linux.vnet.ibm.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A workaround for a warning introduced a use of the NO_IRQ
macro that should have been gone for a long time.
It is clear from the code that the value cannot actually
be used, but apparently there was a configuration at
some point that caused a warning, so instead of just
reverting that patch, this rearranges the code in a way that
the warning cannot reappear.
bq->charger is initialized in bq24257_power_supply_init.
Therefore, bq24257_power_supply_init should be called before the
registration of the IRQ handler bq24257_irq_handler_thread that calls
power_supply_changed(bq->charger).
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Cc: Aurelien Chanot <chanot.a@gmail.com> Cc: Andreas Dannenberg <dannenberg@ti.com> Cc: Sebastian Reichel <sre@kernel.org> Cc: David Woodhouse <dwmw2@infradead.org> Fixes: 2219a935963e ("power_supply: Add TI BQ24257 charger driver") Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have a global qpt_mask as that does not support the
multiple chip model which qib has. Instead rely on the value which
exists already in the device data (dd).
Fixes: 898fa52b4ac3 "IB/qib: Remove qpn, qp tables and related variables from qib" Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_completion_interruptible_timeout return 0 on timeout and
-ERESTARTSYS if interrupted. The check for
!wait_for_completion_interruptible_timeout() would report an interrupt
as timeout. Further, while HZ/50 will work most of the time it could
fail for HZ < 50, so this is switched to msecs_to_jiffies(20).
Fixes: 13a9930d15b4 ("staging: ks7010: add driver from Nanonote extra-repository") Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fadbe0cd5292851608e2e01b91d9295fa287b9fe ("staging: rtl8188eu:
Remove rtw_zmalloc(), wrapper for kzalloc()") changed all allocation
calls to be GFP_KERNEL even though the original wrapper was testing
to determine if the caller was in atomic mode. Most of the mistakes
were corrected with commit 33dc85c3c667209c930b2dac5ccbc2a365e06b7a
("staging: r8188eu: Fix scheduling while atomic error introduced in
commit fadbe0cd"); however, two kzalloc calls were missed as the
call only happens when the driver is shutting down.
Commit 6fba39cf32a3 ("staging: sm750fb: use BIT macro for
PANEL_DISPLAY_CTRL single-bit fields") accidentally changed the
CLOCK_PHASE logic from '|=' to '=' which clears all the previously set
bits.
Fixes: 6fba39cf32a3 ("staging: sm750fb: use BIT macro for PANEL_DISPLAY_CTRL single-bit fields") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added Hi6220 Ion code fails to build when the ION_OF helpers
are not present:
drivers/staging/android/ion/hisilicon/hi6220_ion.o: In function `hi6220_ion_remove':
hi6220_ion.c:(.text.hi6220_ion_remove+0x4c): undefined reference to `ion_destroy_platform_data'
drivers/staging/android/ion/hisilicon/hi6220_ion.o: In function `hi6220_ion_probe':
hi6220_ion.c:(.text.hi6220_ion_probe+0x5c): undefined reference to `ion_parse_dt'
hi6220_ion.c:(.text.hi6220_ion_probe+0xf8): undefined reference to `ion_destroy_platform_data'
This selects the symbol when needed.
Fixes: 2b40182a19bc ("staging: android: ion: Add ion driver for Hi6220 SoC platform") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison for devnr limits is off-by-one, the current check
allows 0 to AD5755_NUM_CHANNELS and the limit should be in fact
0 to AD5755_NUM_CHANNELS - 1. This can lead to an out of bounds
write to pdata->dac[devnr]. Fix this by replacing > with >= on the
comparison.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Fixes: c947459979c6 ("iio: ad5755: add support for dt bindings") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d88429a695a4 ("ASoC: dapm: Add output driver widget") added
the snd_soc_dapm_out_drv ID for the output driver widget, which is
the same as the PGA widget, with a later power sequence number.
Commit 19a2557b76d6 ("ASoC: dapm: Add kcontrol support for PGAs")
then added kcontrol support for PGA widgets, but failed to account
for output driver widgets. Attempts to use kcontrols with output
driver widgets result in silent failures, with the developer having
little idea about what went on.
Add snd_soc_dapm_out_drv to the switch/case block under snd_soc_dapm_pga
in dapm_create_or_share_kcontrol, since they are essentially the same.
Fixes: 19a2557b76d6 (ASoC: dapm: Add kcontrol support for PGAs) Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value for the second channel in _ENUM_DOUBLE (double channel) MUXs
is not correctly updated, due to using the wrong bit shift.
Use the correct bit shift, so both channels toggle together.
Fixes: 3727b4968453 (ASoC: dapm: Consolidate MUXs and value MUXs) Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If soc_dapm_read() fails, val will be uninitialized, and bogus values
will be written later:
ret = soc_dapm_read(dapm, reg, &val);
val = (val >> shift) & mask;
However, the compiler does not give a warning. Return on error before
val is really used to avoid this.
This is similar to the commit 6912831623c5 ("ASoC: dapm: Fix
uninitialized variable in snd_soc_dapm_get_enum_double()")
Fixes: ce0fc93ae56e (ASoC: Add DAPM support at the component level) Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently omap-rng checks the return value of pm_runtime_get_sync and
reports failure if anything is returned, however it should be checking
if ret < 0 as pm_runtime_get_sync return 0 on success but also can return
1 if the device was already active which is not a failure case. Only
values < 0 are actual failures.
Fixes: 61dc0a446e5d ("hwrng: omap - Fix assumption that runtime_get_sync will always succeed") Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the retrn value check which testing the wrong variable
in ccp_dmaengine_register().
Fixes: 58ea8abf4904 ("crypto: ccp - Register the CCP as a DMA resource") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 8996eafdcbad ("crypto: ahash - ensure statesize is non-zero"),
all ahash drivers are required to implement import()/export(), and must have
a non-zero statesize. Fix this for the ARM Crypto Extensions GHASH
implementation.
So far, sub part of mv_cesa_int was responsible of dequeuing complete
requests, then call the 'cleanup' operation on these reqs and call the
crypto api callback 'complete'. The problem is that the transformation
context 'ctx' is retrieved only once before the while loop. Which means
that the wrong 'cleanup' operation might be called on the wrong type of
cesa requests, it can lead to memory corruptions with this message:
The cipher block size for GCM is 16 bytes, and thus the CTR transform
used in crypto_gcm_setkey() will also expect a 16-byte IV. However,
the code currently reserves only 8 bytes for the IV, causing
an out-of-bounds access in the CTR transform. This patch fixes
the issue by setting the size of the IV buffer to 16 bytes.
Fixes: 84c911523020 ("[CRYPTO] gcm: Add support for async ciphers") Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, in mv_cesa_{md5,sha1,sha256}_init creq->state is initialized
before the call to mv_cesa_ahash_init. This is wrong because this
function fills creq with zero by using memset, so its 'state' that
contains the default DIGEST is overwritten. This commit fixes the issue
by initializing creq->state just after the call to mv_cesa_ahash_init.
commit 7a0adc83f34d ("ath10k: improve tx scheduling") is causing
severe throughput drop in multi client mode. This issue is originally
reported in veriwave setup with 50 clients with TCP downlink traffic.
While increasing number of clients, the average throughput drops
gradually. With 50 clients, the combined peak throughput is decreased
to 98 Mbps whereas reverting given commit restored it to 550 Mbps.
Processing txqs for every tx completion is causing overhead. Ideally for
management frame tx completion, pending txqs processing can be avoided.
The change partly reverts the commit "ath10k: improve tx scheduling".
Processing pending txqs after all skbs tx completion will yeild enough
room to burst tx frames.
Fixes: 7a0adc83f34d ("ath10k: improve tx scheduling") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When user requests for survey dump data, driver is providing wrong survey
information. This information we sent is the survey data that we have
collected during previous user request.
This issue occurs because we request survey dump for wrong channel. With
this change, we correctly display the correct and current survey
information to userspace.
In the wake tx queue path, we are not checking if the frame to be sent
takes management path or not. For eg. QOS null func frame coming here will
take the management path. Since we are not incrementing the descriptor
counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is
possible to see negative values.
When the above counter reaches a negative value, we will not be sending a
probe response out.
if (is_presp &&
ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx)
For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against
num_pending_mgmt_tx (int) and the above condtions comes true if the counter
is negative and we drop the probe response.
To avoid this, check on the wake tx queue path as well for the tx path of
the frame and increment the appropriate counters
Fixes: cac085524cf1 "ath10k: move mgmt descriptor limit handle under mgmt_tx" Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in
the commit 7e247a9e88dc ("ath10k: add dynamic tx mode switch
config support for qca4019"). This patch adds the service to
avoid mismatch between host and target.
Fixes: 7e247a9e88dc ("ath10k: add dynamic tx mode switch config support for qca4019") Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent patch "mwifiex: fix NULL pointer" skips extended scan event
handling when suspend is in progress. It created a problem for scan
after interface disabled/enabled case.
This patch solves the problem by checking netif_running() status.
Fixes:16d25da94f3d654 ("mwifiex: fix NULL pointer dereference during suspend") Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AID gets updated during TDLS setup, but modified value isn't reflected
in "priv->assoc_rsp_buf". This causes TDLS setup failure. The problem is
fixed here.
Fixes: 4aff53ef18e4a4 ("mwifiex: parsing aid while receiving..") Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
X722 hardware requires using the admin queue to configure RSS. This
function was previously re-written in commit e69ff813af35 ("i40e: rework
the functions to configure RSS with similar parameters").
However, the previous refactor did not work correctly for a few reasons
(a) it does not check whether seed is NULL before using it, resulting in
a NULL pointer dereference
(b) it does not even bother to use the passed in *lut parameter which
defines the requested lookup table. Instead it uses its own round robin
table.
Fix these issues by re-writing it to be similar to i40e_config_rss_reg
and i40e_get_rss_aq.
Fixes: e69ff813af35 ("i40e: rework the functions to configure RSS with similar parameters", 2015-10-21) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We shifted the locking around a bit but forgot to delete this unlock so
now it can unlock twice.
Fixes: cd3be169a5ff ('i40e: Move the mutex lock in i40e_client_unregister') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master
is complete; it reduces the device reference count to zero, which and results
in device memory being freed. The subsequent call to spi_master_put is
unnecessary and results in an access to free memory. Drop it.
Fixes: 9298bc727385 ("spi: spi-fsl-dspi: Remove spi-bitbang") Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable i contains a total number of resources (including
IORESOURCE_IRQ). However, we want the dmem_region_start to point
after the last resource of type IORESOURCE_MEM. The original behaviour
leads (very likely) to skipping several UIO mapping regions and makes
them useless. Fix this by computing dmem_region_start from the uiomem
which points to the last used UIO mapping.
Fixes: 0a0c3b5a24bd ("Add new uio device for dynamic memory allocation") Signed-off-by: Jan Viktorin <viktorin@rehivetech.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de5461970b3e9e194 ("coresight: tmc: allocating memory when needed")
removed the static allocation of buffer for the trace data in ETR mode in
tmc_probe. However it failed to remove the "devm_free_coherent" in
tmc_probe when the probe fails due to other reasons. This patch gets
rid of the incorrect dma_free_coherent() call.
Without this patch irq_domain_disassociate() cannot properly release the
interrupt. In fact, irq_map_generic_chip() checks a bit on 'gc->installed'
but said bit is never cleared, only set.
Commit 088f40b7b027 ("genirq: Generic chip: Add linear irq domain support")
added irq_map_generic_chip() function and also stated "This lacks a removal
function for now".
This commit provides an implementation of an unmap function that can be
called by irq_domain_disassociate().
[ tglx: Made the function static and removed the export as we have neither
a prototype nor a modular user. ]
Fixes: 088f40b7b027 ("genirq: Generic chip: Add linear irq domain support") Signed-off-by: Sebastian Frias <sf84@laposte.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Mason <slash.tmp@free.fr> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/579F5C5A.2070507@laposte.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 704c4b0ddc03 ("cxlflash: Shutdown notify support for CXL Flash
cards") was recently introduced to notify the AFU when a system is going
down. Due to the position of the cxlflash driver in the device stack,
cxlflash devices are _always_ removed during a reboot/shutdown. This can
lead to a crash if the cxlflash shutdown hook is invoked _after_ the
shutdown hook for the owning virtual PHB. Furthermore, the current
implementation of shutdown/remove hooks for cxlflash are not tolerant to
being invoked when the device is not enabled. This can also lead to a
crash in situations where the remove hook is invoked after the device
has been removed via the vPHBs shutdown hook. An example of this
scenario would be an EEH reset failure while a reboot/shutdown is in
progress.
To solve both problems, the shutdown hook for cxlflash is updated to
simply remove the device. This path already includes the AFU
notification and thus this solution will continue to perform the
original intent. At the same time, the remove hook is updated to protect
against being called when the device is not enabled.
Fixes: 704c4b0ddc03 ("cxlflash: Shutdown notify support for CXL Flash
cards") Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We know that 'retval = 0' because it has been tested a few lines above.
So, if 'devm_kmalloc' fails, 0 will be returned instead of an error code.
Return -ENOMEM instead.
Fixes: 8b4c0009313f ("rt2x00usb: Use usb anchor to manage URB") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When file permissions are modified via chmod(2) and the user is not in
the owning group or capable of CAP_FSETID, the setgid bit is cleared in
inode_change_ok(). Setting a POSIX ACL via setxattr(2) sets the file
permissions as well as the new ACL, but doesn't clear the setgid bit in
a similar way; this allows to bypass the check in chmod(2). Fix that.
References: CVE-2016-7097 Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Juerg Haefliger <juerg.haefliger@hpe.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use obj->phys_handle to choose the pread/pwrite path, but as
obj->phys_handle is a union with obj->userptr, we then mistakenly use
the phys_handle path for userptr objects within pread/pwrite.
When we enable the per-register access mmiodebug, it is to detect which
access is illegal. Reporting on earlier untraced access outside of the
mmiodebug does not help debugging (as the suspicion is immediately put
upon the current register which is not at fault)!
Allow returning "connected" or "unknown" connector status for DP branch
devices that don't have an EDID. Currently we'd claim the thing as
"disconnected" if there is no EDID.
This stuff used to broken already, I think, but it got more broken by
commit f21a21983ef1 ("drm/i915: Splitting intel_dp_detect")
Cc: Damien Cassou <damien@cassou.me> Cc: freedesktop.org@gp.mailgun.org Cc: Arno <blouin.arno@gmail.com> Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com> Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Tested-by: Arno <blouin.arno@gmail.com> Fixes: f21a21983ef1 ("drm/i915: Splitting intel_dp_detect")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83348 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1475481316-8194-2-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
(cherry picked from commit 5cb651a7959310ef4dbb0b93f005b10286789656) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't rely on connector->status in the detect() hook if the long hpd
was already handled by the dig_port_work as that won't update
connector->status. Thus we have to defer the long hpd handling entirely
until the hotplug work runs to avoid the double long hpd handling
the "detect_done" flag is trying to prevent.
We'll start to depend on connector->status being up to date in a
following patch.
Cc: Damien Cassou <damien@cassou.me> Cc: freedesktop.org@gp.mailgun.org Cc: Arno <blouin.arno@gmail.com> Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com> Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Tested-by: Arno <blouin.arno@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83348 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1475481316-8194-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
(cherry picked from commit 27d4efc5591a5853de54713bc717de73c8951e17) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DPLL_SDVO_HIGH_SPEED must be set for SDVO/HDMI/DP, but nowhere is it
forbidden to set it for LVDS/CRT as well. So let's also set it on
CRT to make it possible to share the DPLL between HDMI and CRT.
What that bit apparently does is enable the x5 clock to the port,
which then pumps out the bits on both edges of the clock. The DAC
doesn't need that clock since it's not pumping out bits, but I don't
think it hurts to have the DPLL output that clock anyway.
This is fairly important on IVB since it has only two DPLLs with three
pipes. So trying to drive three or more PCH ports with three pipes
is only possible when at least one of the DPLLs gets shared between
two of the pipes.
SNB doesn't really need to do this since it has only two pipes. It could
be done to avoid enabling the second DPLL at all in certain cases, but
I'm not sure that's such a huge win. So let's not do it for SNB, at
least for now. On ILK it never makes sense as the DPLLs can't be shared.
v2: Just always enable the high speed clock to keep things simple (Daniel)
Beef up the commit message a bit (Daniel)
Cc: Nick Yamane <nick.diego@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Tested-by: Nick Yamane <nick.diego@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97204 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1474878646-17711-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
(cherry picked from commit 7d7f8633a82763577727762ff3ac1df3017cb8fe) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're enabling a pipe, we'll need to modify the watermarks on all
active planes. Since those planes won't be added to the state on
their own, we need to add them ourselves.
Signed-off-by: Lyude <cpaul@redhat.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-6-git-send-email-cpaul@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like the TSEG lives just above TOUD, stolen comes after TSEG.
The spec seems somewhat self-contradictory in places, in the ESMRAMC
register desctription it says:
TSEG Size:
10=(TOUD + 512 KB) to TOUD
11 =(TOUD + 1 MB) to TOUD
so that agrees with TSEG being at TOUD. But the example given
elsehwere in the spec says:
TOUD equals 62.5 MB = 03E7FFFFh
TSEG selected as 512 KB in size,
Graphics local memory selected as 1 MB in size
General System RAM available in system = 62.5 MB
General system RAM range00000000h to 03E7FFFFh
TSEG address range03F80000h to 03FFFFFFh
TSEG pre-allocated from03F80000h to 03FFFFFFh
Graphics local memory pre-allocated from03E80000h to 03F7FFFFh
so here we have TSEG above stolen.
Real world evidence agrees with the TOUD->TSEG->stolen order however, so
let's fix up the code to account for the TSEG size.
Cc: Taketo Kabe <fdporg@vega.pgw.jp> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Fixes: 0ad98c74e093 ("drm/i915: Determine the stolen memory base address on gen2") Fixes: a4dff76924fe ("x86/gpu: Add Intel graphics stolen memory quirk for gen2 platforms") Reported-by: Taketo Kabe <fdporg@vega.pgw.jp> Tested-by: Taketo Kabe <fdporg@vega.pgw.jp>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96473 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1470653919-27251-1-git-send-email-ville.syrjala@linux.intel.com Link: http://download.intel.com/design/chipsets/datashts/25251405.pdf Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our current implementation of live status check (repeat 9 times
with 10ms delays between each attempt as a workaround for
buggy displays) imposes a rather serious penalty, time wise,
on intel_hdmi_detect(). Since we we already skip live status
checks on platforms before gen 7, and since we seem to have
coped quite well before the live status check was introduced
for newer platforms too, the previous behaviour is probably
preferable, at least unless someone can point to a use-case
that the live status check improves (apart from "Bspec says so".)
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com> Fixes: 237ed86c693d ("drm/i915: Check live status before reading edid") Fixes: f8d03ea0053b ("drm/i915: increase the tries for HDMI hotplug live status checking")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97139
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94014 Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20160817124748.31208-1-david.weinehall@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use it to move knowledge about the SAGV-supporting platforms from
the callers to the SAGV code.
We'll add more platforms to intel_has_sagv(), so IMHO it makes more
sense to move all this to a single function instead of patching all
the callers every time we add SAGV support to a new platform.
v2: Move I915_SAGV_NOT_CONTROLLED to the new function (Lyude).
The plan is to introduce intel_has_sagv() and then use it to discover
which platforms actually support it.
I thought about keeping the functions with their current skl names,
but found two problems: (i) skl_has_sagv() would become a very
confusing name, and (ii) intel_atomic_commit_tail() doesn't seem to be
calling any functions whose name start with a platform name, so the
"intel_" naming scheme seems make more sense than the "firstplatorm_"
naming scheme here.
We forgot the "res_blocks += y_tile_minimum" that's described on step
V of our documentation.
Again, this should only affect the Y tiling cases.
It looks like the relevant code was introduced in 0fda65680e92, but
there's always the possibility that it matched our specification when
it was introduced, and then the specification changed while the code
stayed the same. So we can't really say this was a regression, but
let's try to add a "Fixes" tag anyway to help backporting.
v2: Try to add a "Fixes" tag (Maarten).
Fixes: 0fda65680e92 ("drm/i915/skl: Update watermarks for Y tiling") Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Lyude <cpaul@redhat.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1474578035-424-8-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 75676ed423a6acf9e2b1df52fbc036a51e11fb7a) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The confusing thing is that plane_blocks_per_line is listed as part of
the method 2 calculation but is also used for other things. We
calculated it in two different places and different ways: one inside
skl_wm_method2() and the other inside skl_compute_plane_wm(). The
skl_wm_method2() implementation is the one that matches the
specification.
With this patch we fix the skl_compute_plane_wm() calculation and just
pass it as a parameter to skl_wm_method2(). We also take care to not
modify the value of plane_bytes_per_line since we're going to rely on
it having a correct value in later patches.
This should affect the watermarks for Linear and Y-tiled.
From my analysis, it looks like the two plane_blocks_per_line
variables got out of sync on 0fda65680e92, but we can't really say
that commit was a regression, it looks like just an incomplete fix.
There's always the possibility that 0fda65680e92 matched our
specification at that time, and then later the specification changed.
v2: Try to add a "Fixes" tag (Maarten).
Fixes: 0fda65680e92 ("drm/i915/skl: Update watermarks for Y tiling") Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Lyude <cpaul@redhat.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1474578035-424-7-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 7a1a8aed67e0a60772defe3f6499eb340da48634) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During watermarks calculations, this value is used in 3 different
places. Only one of them was not using a hardcoded 4. Move the code up
so everybody can benefit from the actual value.
This should only help on situations with Y tiling + 90/270 rotation +
1 or 2 bpp or NV12.
Bspec says:
"The mailbox response data may not account for memory read latency.
If the mailbox response data for level 0 is 0us, add 2 microseconds
to the result for each valid level."
This means we should only do the +2 in case wm[0] == 0, not always.
So split the sanitizing implementation from the WA implementation and
fix the WA implementation.
We were previously adding all the planes owned by the CRTC even when
the ddb partitioning didn't change for them. As a consequence, a lot
of functions were being called when we were just moving the cursor
around the screen, such as skylake_update_primary_plane().
This was causing flickering on the primary plane when moving the
cursor. I'm not 100% sure which operation caused the flickering, but
we were writing to a lot of registers, so it could be any of these
writes. With this patch, just moving the mouse won't add the primary
plane to the commit since it won't trigger a change in DDB
partitioning.
v2: Use skl_ddb_entry_equal() (Lyude).
v3: Change Reported-and-bisected-by: to Reported-by: for checkpatch
Fixes: 05a76d3d6ad1 ("drm/i915/skl: Ensure pipes with changed wms get added to the state")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97888 Cc: Mike Lothian <mike@fireburn.co.uk> Reported-by: Mike Lothian <mike@fireburn.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Lyude <cpaul@redhat.com> Link: http://patchwork.freedesktop.org/patch/msgid/1475177808-29955-1-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 7f60e200e254cd53ad1bd74a56bdd23e813ac4b7) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i915 sometimes needs to disable planes in the middle of an atomic
commit, and then reenable them later in the same commit. Because of
this, we can't make the assumption that the state of the plane actually
changed. Since the state of the plane hasn't actually changed, neither
have it's watermarks. And if the watermarks hasn't changed then we
haven't populated skl_results with anything, which means we'll end up
zeroing out a plane's watermarks in the middle of the atomic commit
without restoring them later.
Simple reproduction recipe:
- Get a SKL laptop, launch any kind of X session
- Get two extra monitors
- Keep hotplugging both displays (so that the display configuration
jumps from 1 active pipe to 3 active pipes and back)
- Eventually underrun
Changes since v1:
- Fix incorrect use of "it's"
Changes since v2:
- Add reproduction recipe
Now that we can hook into update_crtcs and control the order in which we
update CRTCs at each modeset, we can finish the final step of fixing
Skylake's watermark handling by performing DDB updates at the same time
as plane updates and watermark updates.
The first major change in this patch is skl_update_crtcs(), which
handles ensuring that we order each CRTC update in our atomic commits
properly so that they honor the DDB flush order.
The second major change in this patch is the order in which we flush the
pipes. While the previous order may have worked, it can't be used in
this approach since it no longer will do the right thing. For example,
using the old ddb flush order:
We have pipes A, B, and C enabled, and we're disabling C. Initial ddb
allocation looks like this:
| A | B |xxxxxxx|
Since we're performing the ddb updates after performing any CRTC
disablements in intel_atomic_commit_tail(), the space to the right of
pipe B is unallocated.
1. Flush pipes with new allocation contained into old space. None
apply, so we skip this
2. Flush pipes having their allocation reduced, but overlapping with a
previous allocation. None apply, so we also skip this
3. Flush pipes that got more space allocated. This applies to A and B,
giving us the following update order: A, B
This is wrong, since updating pipe A first will cause it to overlap with
B and potentially burst into flames. Our new order (see the code
comments for details) would update the pipes in the proper order: B, A.
As well, we calculate the order for each DDB update during the check
phase, and reference it later in the commit phase when we hit
skl_update_crtcs().
This long overdue patch fixes the rest of the underruns on Skylake.
Changes since v1:
- Add skl_ddb_entry_write() for cursor into skl_write_cursor_wm()
Changes since v2:
- Use the method for updating CRTCs that Ville suggested
- In skl_update_wm(), only copy the watermarks for the crtc that was
passed to us
Changes since v3:
- Small comment fix in skl_ddb_allocation_overlaps()
Changes since v4:
- Remove the second loop in intel_update_crtcs() and use Ville's
suggestion for updating the ddb allocations in the right order
- Get rid of the second loop and just use the ddb state as it updates
to determine what order to update everything in (thanks for the
suggestion Ville)
- Simplify skl_ddb_allocation_overlaps()
- Split actual overlap checking into it's own helper
Fixes: 0e8fb7ba7ca5 ("drm/i915/skl: Flush the WM configuration") Fixes: 8211bd5bdf5e ("drm/i915/skl: Program the DDB allocation")
[omitting CC for stable, since this patch will need to be changed for
such backports first]
Testcase: kms_cursor_legacy
Testcase: plane-all-modeset-transition Signed-off-by: Lyude <cpaul@redhat.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1471961565-28540-2-git-send-email-cpaul@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have to write ddb allocations at the same time as we do other
plane updates, we're going to need to be able to control the order in
which we execute modesets on each pipe. The easiest way to do this is to
just factor this section of intel_atomic_commit_tail()
(intel_atomic_commit() for stable branches) into it's own function, and
add an appropriate display function hook for it.
Based off of Matt Rope's suggestions
Changes since v1:
- Drop pipe_config->base.active check in intel_update_crtcs() since we
check that before calling the function
Signed-off-by: Lyude <cpaul@redhat.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[omitting CC for stable, since this patch will need to be changed for
such backports first] Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1471961565-28540-1-git-send-email-cpaul@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thanks to Ville for suggesting this as a potential solution to pipe
underruns on Skylake.
On Skylake all of the registers for configuring planes, including the
registers for configuring their watermarks, are double buffered. New
values written to them won't take effect until said registers are
"armed", which is done by writing to the PLANE_SURF (or in the case of
cursor planes, the CURBASE register) register.
With this in mind, up until now we've been updating watermarks on skl
like this:
So this patch moves all of the watermark writes into the right place;
inside of the vblank evasion where we update all of the registers for
each plane. While this patch doesn't fix everything, it does allow us to
update the watermark values in the way the hardware expects us to.
Changes since original patch series:
- Remove mutex_lock/mutex_unlock since they don't do anything and we're
not touching global state
- Move skl_write_cursor_wm/skl_write_plane_wm functions into
intel_pm.c, make externally visible
- Add skl_write_plane_wm calls to skl_update_plane
- Fix conditional for for loop in skl_write_plane_wm (level < max_level
should be level <= max_level)
- Make diagram in commit more accurate to what's actually happening
- Add Fixes:
Changes since v1:
- Use IS_GEN9() instead of IS_SKYLAKE() since these fixes apply to more
then just Skylake
- Update description to make it clear this patch doesn't fix everything
- Check if pipes were actually changed before writing watermarks
Changes since v2:
- Write PIPE_WM_LINETIME during vblank evasion
Changes since v3:
- Rebase against new SAGV patch changes
Changes since v4:
- Add a parameter to choose what skl_wm_values struct to use when
writing new plane watermarks
Changes since v5:
- Remove cursor ddb entry write in skl_write_cursor_wm(), defer until
patch 6
- Write WM_LINETIME in intel_begin_crtc_commit()
Changes since v6:
- Remove redundant dirty_pipes check in skl_write_plane_wm (we check
this in all places where we call this function, and it was supposed
to have been removed earlier anyway)
- In i9xx_update_cursor(), use dev_priv->info.gen >= 9 instead of
IS_GEN9(dev_priv). We do this everywhere else and I'd imagine this
needs to be done for gen10 as well
Changes since v7:
- Fix rebase fail (unused variable obj)
- Make struct skl_wm_values *wm const
- Fix indenting
- Use INTEL_GEN() instead of dev_priv->info.gen
Changes since v8:
- Don't forget calls to skl_write_plane_wm() when disabling planes
- Use INTEL_GEN(), not INTEL_INFO()->gen in intel_begin_crtc_commit()
The Akai MIDImix (09e8:0031) is a MIDI fader controller that speaks
regular MIDI and works well with Linux. However, initialization gets
delayed due to reports timeout:
[3643645.631124] hid-generic 0003:09E8:0031.0020: timeout initializing reports
[3643645.632416] hid-generic 0003:09E8:0031.0020: hiddev0: USB HID v1.11 Device [AKAI MIDI Mix] on usb-0000:00:14.0-2/input0
Adding "usbhid.quirks=0x09e8:0x0031:0x20000000" on the kernel
command line makes the issues go away.
Since using clk_register_divider to setup the pixel clock, regmap
is no longer used. Regmap did take care of DCU using different
endianness. Check endianness using the device-tree property
"big-endian" to determine the location of DIV_RATIO.
Fixes: 2d701449bce1 ("drm/fsl-dcu: use common clock framework for pixel clock divider") Reported-by: Meng Yi <meng.yi@nxp.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Tested-by: Meng Yi <meng.yi@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that we really only report a GPU reset if one has happened since the
creation of the context.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Backlight enable is supposed to do a full setup of the backlight. We
were missing the PWM alternate increment bit in the south chicken
registers on lpt+ pch. This potentially caused a PWM frequency change
when the chicken register value was lost e.g. on suspend.
v2 by Jani, rebase on the patch caching alt increment
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97486
References: https://bugs.freedesktop.org/show_bug.cgi?id=67454 Cc: Cooper Chiou <cooper.chiou@intel.com> Cc: Wei Shun Chen <wei.shun.chang@intel.com> Cc: Gary C Wang <gary.c.wang@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Shawn Lee <shawn.c.lee@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/8265f5935bd31c039ddfc82819d26c2ca1ae9cba.1474281249.git.jani.nikula@intel.com
(cherry picked from commit e29aff05f239f8dd24e9ee7816fd96726e20105a) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_buf_export() adds a reference to the owning module to the dmabuf (to
prevent the driver from being unloaded whilst a third party still refers
to the dmabuf). However, drm_gem_prime_export() was passing its own
THIS_MODULE (i.e. drm.ko) rather than the driver. Extract the right
owner from the device->fops instead.
v2: Use C99 initializers to zero out unset elements of
dma_buf_export_info
v3: Extract the right module from dev->fops.
Testcase: igt/vgem_basic/unload Reported-by: Petri Latvala <petri.latvala@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Petri Latvala <petri.latvala@intel.com> Cc: Christian König <christian.koenig@amd.com> Tested-by: Petri Latvala <petri.latvala@intel.com> Reviewed-by: Petri Latvala <petri.latvala@intel.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161005122145.1507-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the introduction of bin/render pipelining, the previous job may
not be completed when we start binning the next one. If the previous
job wrote our VBO, IB, or CS textures, then the binning stage might
get stale or uninitialized results.
Fixes the major rendering failure in glmark2 -b terrain.
Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: ca26d28bbaa3 ("drm/vc4: improve throughput by pipelining binning and rendering jobs") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reverting this patch, as it incorrectly assumes the additional length
for INQUIRY in target_complete_cmd_with_length() is SCSI allocation
length, which breaks existing user-space code when SCSI allocation
length is smaller than additional length.
root@scsi-mq:~# sg_inq --len=4 -vvvv /dev/sdb
found bsg_major=253
open /dev/sdb with flags=0x800
inquiry cdb: 12 00 00 00 04 00
duration=0 ms
inquiry: pass-through requested 4 bytes (data-in) but got -28 bytes
inquiry: pass-through can't get negative bytes, say it got none
inquiry: got too few bytes (0)
INQUIRY resid (32) should never exceed requested len=4
inquiry: failed requesting 4 byte response: Malformed response to
SCSI command [resid=32]
AFAICT the original change was not to address a specific host issue,
so go ahead and revert to original logic for now.
Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Sumit Rai <sumitrai96@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a bug where a local EXTENDED_COPY WRITE or READ
backend I/O request would always return SAM_STAT_CHECK_CONDITION,
even if underlying xcopy_pt_cmd->se_cmd generated a different
SCSI status code.
ESX host environments expect to hit SAM_STAT_RESERVATION_CONFLICT
for certain scenarios, and SAM_STAT_CHECK_CONDITION results in
non-retriable status for these cases.
Tested on v4.1.y with ESX v5.5u2+ with local IBLOCK backend copy.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Cc: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Dinesh Israni <ddi@datera.io> Signed-off-by: Dinesh Israni <ddi@datera.io> Cc: Dinesh Israni <ddi@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a bug where EXTENDED_COPY across multiple LUNs
results in a CHECK_CONDITION when the source + destination are not
located on the same physical node.
ESX Host environments expect sense COPY_ABORTED w/ COPY TARGET DEVICE
NOT REACHABLE to be returned when this occurs, in order to signal
fallback to local copy method.
As described in section 6.3.3 of spc4r22:
"If it is not possible to complete processing of a segment because the
copy manager is unable to establish communications with a copy target
device, because the copy target device does not respond to INQUIRY,
or because the data returned in response to INQUIRY indicates
an unsupported logical unit, then the EXTENDED COPY command shall be
terminated with CHECK CONDITION status, with the sense key set to
COPY ABORTED, and the additional sense code set to COPY TARGET DEVICE
NOT REACHABLE."
Tested on v4.1.y with ESX v5.5u2+ with BlockCopy across multiple nodes.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Cc: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Dinesh Israni <ddi@datera.io> Signed-off-by: Dinesh Israni <ddi@datera.io> Cc: Dinesh Israni <ddi@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a regression in >= v4.1.y code where the original
SCF_ACK_KREF assignment in target_get_sess_cmd() was dropped upstream
in commit 054922bb, but the series for addressing TMR ABORT_TASK +
LUN_RESET with fabric session reinstatement in commit febe562c20 still
depends on this code in transport_cmd_finish_abort().
The regression manifests itself as a se_cmd->cmd_kref +1 leak, where
ABORT_TASK + LUN_RESET can hang indefinately for a specific I_T session
for drivers using SCF_ACK_KREF, resulting in hung kthreads.
The libfc stack assigns exchange IDs based on the CPU the request
was received on, so we need to send the responses via the same CPU.
Otherwise the send logic gets confuses and responses will be delayed,
causing exchange timeouts on the initiator side.
Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs file /sys/fs/ext4/features/encryption was present on kernels
compiled with CONFIG_EXT4_FS_ENCRYPTION=n. This was misleading because
such kernels do not actually support ext4 encryption. Therefore, only
provide this file on kernels compiled with CONFIG_EXT4_FS_ENCRYPTION=y.
Note: since the ext4 feature files are all hardcoded to have a contents
of "supported", it really is the presence or absence of the file that is
significant, not the contents (and this change reflects that).
i_rwsem needs to be acquired while setting an encryption policy so that
concurrent calls to FS_IOC_SET_ENCRYPTION_POLICY are correctly
serialized (especially the ->get_context() + ->set_context() pair), and
so that new files cannot be created in the directory during or after the
->empty_dir() check.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XTS tweak (or IV) was initialized differently on little endian and
big endian systems. Because the ciphertext depends on the XTS tweak, it
was not possible to use an encrypted filesystem created by a little
endian system on a big endian system and vice versa, even if they shared
the same PAGE_SIZE. Fix this by always using little endian.
This will break hypothetical big endian users of ext4 or f2fs
encryption. However, all users we are aware of are little endian, and
it's believed that "real" big endian users are unlikely to exist yet.
So this might as well be fixed now before it's too late.
Usually a validity intercept is a programming error of the host
because of invalid entries in the state description.
We can get a validity intercept if the mode of the runtime
instrumentation control block is wrong. As the host does not know
which modes are valid, this can be used by userspace to trigger
a WARN.
Instead of printing a WARN let's return an error to userspace as
this can only happen if userspace provides a malformed initial
value (e.g. on migration). The kernel should never warn on bogus
input. Instead let's log it into the s390 debug feature.
While at it, let's return -EINVAL for all validity intercepts as
this will trigger an error in QEMU like
This will avoid an endless loop of validity intercepts.
Fixes: c6e5f166373a ("KVM: s390: implement the RI support of guest") Acked-by: Fan Zhang <zhangfan@linux.vnet.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accesses of the rtsx sdmmc's parent device, which is the rtsx usb device,
must be done when it's runtime resumed. Currently this isn't case when
changing the led, so let's fix this by adding a pm_runtime_get_sync() and
a pm_runtime_put() around those operations.
The rtsx_usb_sdmmc driver may bail out in its ->set_ios() callback when no
SD card is inserted. This is wrong, as it could cause the device to remain
runtime resumed when it's unused. Fix this behaviour.
projects / thirdparty / kernel / stable.git / log
