The offset inside the fragment was not used for the dma address and
silent data corruption resulted because TSO makes the checksum match.
Fixes: 077742dac2c7 ("dwc_eth_qos: Add support for Synopsys DWC Ethernet QoS") Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1f718f0f4f97 ("bonding: populate neighbour's private on enslave")
undoes the fix provided by commit c2edacf80e15 ("bonding / ipv6: no addrconf
for slaves separately from master") by effectively setting the slave flag
after the slave has been opened. If the slave comes up quickly enough, it
will go through the IPv6 addrconf before the slave flag has been set and
will get a link local IPv6 address.
In order to ensure that addrconf knows to ignore the slave devices on state
change, set IFF_SLAVE before dev_open() during bonding enslavement.
Fixes: 1f718f0f4f97 ("bonding: populate neighbour's private on enslave") Signed-off-by: Karl Heiss <kheiss@gmail.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Reviewed-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Skb_gso_segment() uses skb control block during segmentation.
This patch adds 32-bytes room for previous control block which
will be copied into all resulting segments.
This patch fixes kernel crash during fragmenting forwarded packets.
Fragmentation requires valid IP CB in skb for clearing ip options.
Also patch removes custom save/restore in ovs code, now it's redundant.
Commit acf8dd0a9d0b ("udp: only allow UFO for packets from SOCK_DGRAM
sockets") disallows UFO for packets sent from raw sockets. We need to do
the same also for SOCK_DGRAM sockets with SO_NO_CHECK options, even if
for a bit different reason: while such socket would override the
CHECKSUM_PARTIAL set by ip_ufo_append_data(), gso_size is still set and
bad offloading flags warning is triggered in __skb_gso_segment().
In the IPv6 case, SO_NO_CHECK option is ignored but we need to disallow
UFO for packets sent by sockets with UDP_NO_CHECK6_TX option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Tested-by: Shannon Nelson <shannon.nelson@intel.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix possible null pointer dereference that may occur when calling
skb_reserve() on a null skb.
Fixes: 879c7220e82 ("net: pktgen: Observe needed_headroom of the device") Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
only when user space passes the addresses should we consider their
presence
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tcp_yeah, use an ssthresh floor of 2, the same floor used by Reno
and CUBIC, per RFC 5681 (equation 4).
tcp_yeah_ssthresh() was sometimes returning a 0 or negative ssthresh
value if the intended reduction is as big or bigger than the current
cwnd. Congestion control modules should never return a zero or
negative ssthresh. A zero ssthresh generally results in a zero cwnd,
causing the connection to stall. A negative ssthresh value will be
interpreted as a u32 and will set a target cwnd for PRR near 4
billion.
Oleksandr Natalenko reported that a system using tcp_yeah with ECN
could see a warning about a prior_cwnd of 0 in
tcp_cwnd_reduction(). Testing verified that this was due to
tcp_yeah_ssthresh() misbehaving in this way.
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When first SYNACK is sent, we already hold rcu_read_lock(), but this
is not true if a SYNACK is retransmitted, as a timer (soft) interrupt
does not hold rcu_read_lock()
Fixes: 45f6fad84cc30 ("ipv6: add complete rcu protection around np->opt") Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
proc_dostring() needs an initialized destination string, while the one
provided in proc_sctp_do_hmac_alg() contains stack garbage.
Thus, writing to cookie_hmac_alg would strlen() that garbage and end up
accessing invalid memory.
Fixes: 3c68198e7 ("sctp: Make hmac algorithm selection for cookie generation dynamic") Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a vxlan interface is created, the driver checks that there is not
another vxlan interface with the same properties. To do this, it checks
the existing vxlan udp socket. Since commit 1c51a9159dde, the creation of
the vxlan socket is done only when the interface is set up, thus it breaks
that test.
Example:
$ ip l a vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip l a vxlan11 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip -br l | grep vxlan
vxlan10 DOWN f2:55:1c:6a:fb:00 <BROADCAST,MULTICAST>
vxlan11 DOWN 7a:cb:b9:38:59:0d <BROADCAST,MULTICAST>
Instead of checking sockets, let's loop over the vxlan iface list.
Fixes: 1c51a9159dde ("vxlan: fix race caused by dropping rtnl_unlock") Reported-by: Thomas Faivre <thomas.faivre@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch 3759824da87b ("tcp: PRR uses CRB mode by default and SS mode
conditionally") introduced a bug that cwnd may become 0 when both
inflight and sndcnt are 0 (cwnd = inflight + sndcnt). This may lead
to a div-by-zero if the connection starts another cwnd reduction
phase by setting tp->prior_cwnd to the current cwnd (0) in
tcp_init_cwnd_reduction().
To prevent this we skip PRR operation when nothing is acked or
sacked. Then cwnd must be positive in all cases as long as ssthresh
is positive:
1) The proportional reduction mode
inflight > ssthresh > 0
2) The reduction bound mode
a) inflight == ssthresh > 0
b) inflight < ssthresh
sndcnt > 0 since newly_acked_sacked > 0 and inflight < ssthresh
Therefore in all cases inflight and sndcnt can not both be 0.
We check invalid tp->prior_cwnd to avoid potential div0 bugs.
In reality this bug is triggered only with a sequence of less common
events. For example, the connection is terminating an ECN-triggered
cwnd reduction with an inflight 0, then it receives reordered/old
ACKs or DSACKs from prior transmission (which acks nothing). Or the
connection is in fast recovery stage that marks everything lost,
but fails to retransmit due to local issues, then receives data
packets from other end which acks nothing.
Fixes: 3759824da87b ("tcp: PRR uses CRB mode by default and SS mode conditionally") Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dst_release should not access dst->flags after decrementing
__refcnt to 0. The dst_entry may be in dst_busy_list and
dst_gc_task may dst_destroy it before dst_release gets a chance
to access dst->flags.
Fixes: d69bbf88c8d0 ("net: fix a race in dst_release()") Fixes: 27b75c95f10d ("net: avoid RCU for NOCACHE dst") Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a qdisc is using per cpu stats (currently just the ingress
qdisc) only the bstats are being freed. This also free's the qstats.
Fixes: b0ab6f92752b9f9d8 ("net: sched: enable per cpu qstats") Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SKF_AD_ALU_XOR_X ancillary is not like the other ancillary data
instructions since it XORs A with X while all the others replace A with
some loaded value. All the BPF JITs fail to clear A if this is used as
the first instruction in a filter. This was found using american fuzzy
lop.
Add a helper to determine if A needs to be cleared given the first
instruction in a filter, and use this in the JITs. Except for ARM, the
rest have only been compile-tested.
Fixes: 3480593131e0 ("net: filter: get rid of BPF_S_* enum") Signed-off-by: Rabin Vincent <rabin@rab.in> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[I stole this patch from Eric Biederman. He wrote:]
> There is no defined mechanism to pass network namespace information
> into /sbin/bridge-stp therefore don't even try to invoke it except
> for bridge devices in the initial network namespace.
>
> It is possible for unprivileged users to cause /sbin/bridge-stp to be
> invoked for any network device name which if /sbin/bridge-stp does not
> guard against unreasonable arguments or being invoked twice on the
> same network device could cause problems.
[Hannes: changed patch using netns_eq]
Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for a process to allocate and accumulate far more FDs than
the process' limit by sending them over a unix socket then closing them
to keep the process' fd count low.
This change addresses this problem by keeping track of the number of FDs
in flight per user and preventing non-privileged processes from having
more FDs in flight than their configured FD limit.
Reported-by: socketpair@gmail.com Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Mitigates: CVE-2013-4312 (Linux 2.0+) Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 2015/11/06, Dmitry Vyukov reported a deadlock involving the splice
system call and AF_UNIX sockets,
http://lists.openwall.net/netdev/2015/11/06/24
The situation was analyzed as
(a while ago) A: socketpair()
B: splice() from a pipe to /mnt/regular_file
does sb_start_write() on /mnt
C: try to freeze /mnt
wait for B to finish with /mnt
A: bind() try to bind our socket to /mnt/new_socket_name
lock our socket, see it not bound yet
decide that it needs to create something in /mnt
try to do sb_start_write() on /mnt, block (it's
waiting for C).
D: splice() from the same pipe to our socket
lock the pipe, see that socket is connected
try to lock the socket, block waiting for A
B: get around to actually feeding a chunk from
pipe to file, try to lock the pipe. Deadlock.
on 2015/11/10 by Al Viro,
http://lists.openwall.net/netdev/2015/11/10/4
The patch fixes this by removing the kern_path_create related code from
unix_mknod and executing it as part of unix_bind prior acquiring the
readlock of the socket in question. This means that A (as used above)
will sb_start_write on /mnt before it acquires the readlock, hence, it
won't indirectly block B which first did a sb_start_write and then
waited for a thread trying to acquire the readlock. Consequently, A
being blocked by C waiting for B won't cause a deadlock anymore
(effectively, both A and B acquire two locks in opposite order in the
situation described above).
Dmitry Vyukov(<dvyukov@google.com>) tested the original patch.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sctp_close, sctp_make_abort_user may return NULL because of memory
allocation failure. If this happens, it will bypass any state change
and never free the assoc. The assoc has no chance to be freed and it
will be kept in memory with the state it had even after the socket is
closed by sctp_close().
So if sctp_make_abort_user fails to allocate memory, we should abort
the asoc via sctp_primitive_ABORT as well. Just like the annotation in
sctp_sf_cookie_wait_prm_abort and sctp_sf_do_9_1_prm_abort said,
"Even if we can't send the ABORT due to low memory delete the TCB.
This is a departure from our typical NOMEM handling".
But then the chunk is NULL (low memory) and the SCTP_CMD_REPLY cmd would
dereference the chunk pointer, and system crash. So we should add
SCTP_CMD_REPLY cmd only when the chunk is not NULL, just like other
places where it adds SCTP_CMD_REPLY cmd.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NCM buffer sizes are negotiated with the device independently of
the network device MTU. The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.
The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size. This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.
Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sysctl performs restrict writes, it allows to write from
a middle position of a sysctl file, which requires us to initialize
the table data before calling proc_dostring() for the write case.
Fixes: 3d1bec99320d ("ipv6: introduce secret_stable to ipv6_devconf") Reported-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Tested-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ip6addrlbl_get() has never worked. If ip6addrlbl_hold() succeeded,
ip6addrlbl_get() will exit with '-ESRCH'. If ip6addrlbl_hold() failed,
ip6addrlbl_get() will use about to be free ip6addrlbl_entry pointer.
Fix this by inverting ip6addrlbl_hold() check.
Fixes: 2a8cc6c89039 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.") Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Packets that arrive from real hardware devices have ip_summed ==
CHECKSUM_UNNECESSARY if the hardware verified the checksums, or
CHECKSUM_NONE if the packet is bad or it was unable to verify it. The
current version of veth will replace CHECKSUM_NONE with
CHECKSUM_UNNECESSARY, which causes corrupt packets routed from hardware to
a veth device to be delivered to the application. This caused applications
at Twitter to receive corrupt data when network hardware was corrupting
packets.
We believe this was added as an optimization to skip computing and
verifying checksums for communication between containers. However, locally
generated packets have ip_summed == CHECKSUM_PARTIAL, so the code as
written does nothing for them. As far as we can tell, after removing this
code, these packets are transmitted from one stack to another unmodified
(tcpdump shows invalid checksums on both sides, as expected), and they are
delivered correctly to applications. We didn’t test every possible network
configuration, but we tried a few common ones such as bridging containers,
using NAT between the host and a container, and routing from hardware
devices to containers. We have effectively deployed this in production at
Twitter (by disabling RX checksum offloading on veth devices).
This code dates back to the first version of the driver, commit
<e314dbdc1c0dc6a548ecf> ("[NET]: Virtual ethernet device driver"), so I
suspect this bug occurred mostly because the driver API has evolved
significantly since then. Commit <0b7967503dc97864f283a> ("net/veth: Fix
packet checksumming") (in December 2010) fixed this for packets that get
created locally and sent to hardware devices, by not changing
CHECKSUM_PARTIAL. However, the same issue still occurs for packets coming
in from hardware devices.
Co-authored-by: Evan Jones <ej@evanjones.ca> Signed-off-by: Evan Jones <ej@evanjones.ca> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Cc: Phil Sutter <phil@nwl.cc> Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Vijay Pandurangan <vijayp@vijayp.ca> Acked-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a set action tunnel attributes should be encoded in a
nested action.
I noticed this because ovs-dpctl was reporting an error
when dumping flows due to the incorrect encoding of tunnel attributes
in a set action.
Fixes: fc4099f17240 ("openvswitch: Fix egress tunnel info.") Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 655fe4effe0f ("usbcore: add sysfs support to xHCI usb3
hardware LPM") introduced usb3_hardware_lpm sysfs node. This
doesn't show the correct status of USB3 U1 and U2 LPM status.
This patch fixes this by replacing usb3_hardware_lpm with two
nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2
(for U2), and recording the U1/U2 LPM status in right places.
This patch should be back-ported to kernels as old as 4.3,
that contains Commit 655fe4effe0f ("usbcore: add sysfs support
to xHCI usb3 hardware LPM").
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code expects the loop to end with "retries" set to zero but, because
it is a post-op, it will end set to -1. I have fixed this by moving the
decrement inside the loop.
Fixes: 014aa2a3c32e ('USB: ipaq: minor ipaq_open() cleanup.') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8520f38099cc ("USB: change hub initialization sleeps to
delayed_work") changed the hub_activate() routine to make part of it
run in a workqueue. However, the commit failed to take a reference to
the usb_hub structure or to lock the hub interface while doing so. As
a result, if a hub is plugged in and quickly unplugged before the work
routine can run, the routine will try to access memory that has been
deallocated. Or, if the hub is unplugged while the routine is
running, the memory may be deallocated while it is in active use.
This patch fixes the problem by taking a reference to the usb_hub at
the start of hub_activate() and releasing it at the end (when the work
is finished), and by locking the hub interface while the work routine
is running. It also adds a check at the start of the routine to see
if the hub has already been disconnected, in which nothing should be
done.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Alexandru Cornea <alexandru.cornea@intel.com> Tested-by: Alexandru Cornea <alexandru.cornea@intel.com> Fixes: 8520f38099cc ("USB: change hub initialization sleeps to delayed_work") CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver requested device firmware version string during probe using
only 24 byte long buffer. That buffer is too small for newer firmware
versions, which causes device firmware hang - device stops responding
to any commands after that. Increase buffer size to 128 which should
be enough for any current and future version strings.
Link: https://github.com/airspy/host/issues/27 Reported-by: Benjamin Vernoux <bvernoux@gmail.com> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
The detection of direction for compress was only taking into account codec
capabilities and not CPU ones. Fix this by checking the CPU side capabilities
as well
Tested-by: Ashish Panwar <ashish.panwar@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want to use a bypassed write in wm5110_clear_pga_volume,
we might disable the DRE whilst the CODEC is powered down. A
normal regmap_write will always go to the hardware (when not on
cache_only) even if the written value matches the cache. As using
a normal write will still achieve the desired behaviour of bring
the cache and hardware in sync, this patch updates the function
to use a normal write, which avoids issues when the CODEC is
powered down.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a sample rate of 12kHz the bclk was taken from the 44.1kHz table as
we test for a multiple of 8kHz. This patch fixes this issue by testing
for multiples of 4kHz instead.
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attempting to use this codec driver triggers a BUG() in regcache_sync()
since no cache type is set. The register map of this device is fairly
small and has few holes so a flat cache is suitable.
Signed-off-by: Mans Rullgard <mans@mansr.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is using completely the wrong mask and value when updating the
register. Since the correct values are already defined in the header,
switch to using a table with explicit constants rather than shifting the
array index.
Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cfcefe0126 ("ASoC: rsnd: add recovery support for under/over flow
error on SRC") added SCU_SYS_INT_EN1 address, but it should be
0x1d4, not 0x1c4. This patch fixup it.
Fixes: cfcefe0126 ("ASoC: rsnd: add recovery support for under/over flow error on SRC") Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make a copy of memory for index_cache rather than directly use the
rt286_index_def to avoid run time error.
Fixes: c418a84a8c8f ("ASoC: Constify reg_default tables") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ALSA timer device doesn't take the disconnection into
account very well; it merely unlinks the timer device at disconnection
callback but does nothing else. Because of this, when an application
accessing the timer device is disconnected, it may release the
resource before actually closed. In most cases, it results in a
warning message indicating a leftover timer instance like:
ALSA: timer xxxx is busy?
But basically this is an open race.
This patch tries to address it. The strategy is like other ALSA
devices: namely,
- Manage card's refcount at each open/close
- Wake up the pending tasks at disconnection
- Check the shutdown flag appropriately at each possible call
Note that this patch has one ugly hack to handle the wakeup of pending
tasks. It'd be cleaner to introduce a new disconnect op to
snd_timer_instance ops. But since it would lead to internal ABI
breakage and it eventually increase my own work when backporting to
stable kernels, I took a different path to implement locally in
timer.c. A cleanup patch will follow at next for 4.5 kernel.
As HD-audio driver does deferred probe internally via workqueue, the
driver might go into the mixed state doing both probe and remove when
the module gets unloaded during the probe work. This eventually
triggers an Oops, unsurprisingly.
For avoiding this race, we just need to flush the pending probe work
explicitly before actually starting the resource release.
When a TLV ioctl with numid zero is handled, the driver may spew a
kernel warning with a stack trace at each call. The check was
intended obviously only for a kernel driver, but not for a user
interaction. Let's fix it.
hrtimer_cancel() waits for the completion from the callback, thus it
must not be called inside the callback itself. This was already a
problem in the past with ALSA hrtimer driver, and the early commit
[fcfdebe70759: ALSA: hrtimer - Fix lock-up] tried to address it.
However, the previous fix is still insufficient: it may still cause a
lockup when the ALSA timer instance reprograms itself in its callback.
Then it invokes the start function even in snd_timer_interrupt() that
is called in hrtimer callback itself, results in a CPU stall. This is
no hypothetical problem but actually triggered by syzkaller fuzzer.
This patch tries to fix the issue again. Now we call
hrtimer_try_to_cancel() at both start and stop functions so that it
won't fall into a deadlock, yet giving some chance to cancel the queue
if the functions have been called outside the callback. The proper
hrtimer_cancel() is called in anyway at closing, so this should be
enough.
This reverts one hunk of
commit ef44a1ec6eee ("ALSA: sound/core: use memdup_user()"), which
replaced a number of kmalloc followed by memcpy with memdup calls.
In this case, we are copying from a struct snd_pcm_hw_params32 to
a struct snd_pcm_hw_params, but the latter is 4 bytes longer than
the 32-bit version, so we need to separate kmalloc and copy calls.
This actually leads to an out-of-bounds memory access later on
in sound/soc/soc-pcm.c:soc_pcm_hw_params() (detected using KASan).
Fixes: ef44a1ec6eee ('ALSA: sound/core: use memdup_user()') Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts one hunk of
commit ef44a1ec6eee ("ALSA: sound/core: use memdup_user()"), which
replaced a number of kmalloc followed by memcpy with memdup calls.
In this case, we are copying from a struct snd_seq_port_info32 to a
struct snd_seq_port_info, but the latter is 4 bytes longer than the
32-bit version, so we need to separate kmalloc and copy calls.
Fixes: ef44a1ec6eee ('ALSA: sound/core: use memdup_user()') Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA timer instance object has a couple of linked lists and they are
unlinked unconditionally at snd_timer_stop(). Meanwhile
snd_timer_interrupt() unlinks it, but it calls list_del() which leaves
the element list itself unchanged. This ends up with unlinking twice,
and it was caught by syzkaller fuzzer.
The fix is to use list_del_init() variant properly there, too.
ALSA timer ioctls have an open race and this may lead to a
use-after-free of timer instance object. A simplistic fix is to make
each ioctl exclusive. We have already tread_sem for controlling the
tread, and extend this as a global mutex to be applied to each ioctl.
The downside is, of course, the worse concurrency. But these ioctls
aren't to be parallel accessible, in anyway, so it should be fine to
serialize there.
A slave timer instance might be still accessible in a racy way while
operating the master instance as it lacks of locking. Since the
master operation is mostly protected with timer->lock, we should cope
with it while changing the slave instance, too. Also, some linked
lists (active_list and ack_list) of slave instances aren't unlinked
immediately at stopping or closing, and this may lead to unexpected
accesses.
This patch tries to address these issues. It adds spin lock of
timer->lock (either from master or slave, which is equivalent) in a
few places. For avoiding a deadlock, we ensure that the global
slave_active_lock is always locked at first before each timer lock.
Also, ack and active_list of slave instances are properly unlinked at
snd_timer_stop() and snd_timer_close().
Last but not least, remove the superfluous call of _snd_timer_stop()
at removing slave links. This is a noop, and calling it may confuse
readers wrt locking. Further cleanup will follow in a later patch.
Actually we've got reports of use-after-free by syzkaller fuzzer, and
this hopefully fixes these issues.
The commit [da6d276957ea: ALSA: usb-audio: Add resume support for
Native Instruments controls] brought a regression where the Native
Instrument audio devices don't get the correct value at update due to
the missing shift at writing. This patch addresses it.
Fixes: da6d276957ea ('ALSA: usb-audio: Add resume support for Native Instruments controls') Reported-and-tested-by: Owen Williams <owilliams@mixxx.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA sequencer code has an open race between the timer setup ioctl and
the close of the client. This was triggered by syzkaller fuzzer, and
a use-after-free was caught there as a result.
This patch papers over it by adding a proper queue->timer_mutex lock
around the timer-related calls in the relevant code path.
ALSA PCM may still have a leftover instance after disconnection and
it delays its release. The problem is that the PCM close code path of
USB-audio driver has a call of snd_usb_autosuspend(). This involves
with the call of usb_autopm_put_interface() and it may lead to a
kernel Oops due to the NULL object like:
We have already a check of disconnection in snd_usb_autoresume(), but
the check is missing its counterpart. The fix is just to put the same
check in snd_usb_autosuspend(), too.
snd_seq_ioctl_remove_events() calls snd_seq_fifo_clear()
unconditionally even if there is no FIFO assigned, and this leads to
an Oops due to NULL dereference. The fix is just to add a proper NULL
check.
Inform userspace that one channel of the internal mic has reversed
polarity, so it does not attempt to add both channels together and
end up with silence.
Reported-by: Andrzej Mendel <andrzej.mendel@gmail.com>
Alsa-info: http://www.alsa-project.org/db/?f=3088f82a0cf977855f92af9db8ad406c04f71efa BugLink: https://bugs.launchpad.net/bugs/1529624 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Then users can remap the keycode from userspace. If without the remap,
the input device will pass KEY_MICMUTE to userspace, but in X11 layer,
it uses KEY_F20 rather than KEY_MICMUTE for XF86AudioMicMute. After
adding the keycode map, users can remap the keycode to any value users
want.
The Lenovo ThinkCenter AIO uses Line2 (NID 0x1b) to implement the
micmute hotkey, here we register an input device and use Line2 unsol
event to collect the hotkey pressing or releasing.
In the meanwhile, the micmute led is controlled by GPIO2, so we
use an existing function alc_fixup_gpio_mic_mute_hook() to control
the led.
[Hui: And there are two places to register the input device, to make
the code simple and clean, move the two same code sections into a
function.]
Without this patch, internal speaker and line-out work,
but front headphone output jack stays silent on the
Mac Pro 4,1.
This code path also gets executed on the MacPro 5,1 due
to identical codec SSID, but i don't know if it has any
positive or adverse effects there or not.
(v2) Implement feedback from Takashi Iwai: Reuse
alc889_fixup_mbp_vref and just add a new nid
0x19 for the MacPro 4,1.
It takes three minutes to enter into hibernation on some OEM SKL
machines and we see many codec spurious response after thaw() opertion.
This is because HDA is still in D0 state after freeze() call and
pci_pm_freeze/pci_pm_freeze_noirq() don't set D3 hot in pci_bus driver.
It seems bios still access HDA when system enter into freeze state,
HDA will receive codec response interrupt immediately after thaw() call.
Because of this unexpected interrupt, HDA enter into a abnormal
state and slow down the system enter into hibernation.
In this patch, we put HDA into D3 hot state in azx_freeze_noirq() and
put HDA into D0 state in azx_thaw_noirq().
V2: Only apply this fix to SKL+
Fix compile error when CONFIG_PM_SLEEP isn't defined
[Yet another fix for CONFIG_PM_SLEEP ifdef and the additional comment
by tiwai]
AudioQuest DragonFly DAC reports a volume control range of 0..50
(0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which
is obviously incorrect and would cause software using the dB information
in e.g. volume sliders to have a massive volume difference in 100..102%
range.
Commit 2d1cb7f658fb ("ALSA: usb-audio: add dB range mapping for some
devices") added a dB range mapping for it with range 0..50 dB.
However, the actual volume mapping seems to be neither linear volume nor
linear dB scale, but instead quite close to the cubic mapping e.g.
alsamixer uses, with a range of approx. -53...0 dB.
Replace the previous quirk with a custom dB mapping based on some basic
output measurements, using a 10-item range TLV (which will still fit in
alsa-lib MAX_TLV_RANGE_SIZE).
Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the
range is 0..50, so if this gets fixed/changed in later HW revisions it
will no longer be applied.
v2: incorporated Takashi Iwai's suggestion for the quirk application
method
Lenovo Thinkpads with Realtek codecs may still have some loud
crackling noises at reboot/shutdown even though a few previous fixes
have been applied. It's because the previous fix (disabling the
default shutup callback) takes effect only at transition of the codec
power state. Meanwhile, at reboot or shutdown, we don't take down the
codec power as default, thus it triggers the same problem unless the
codec is powered down casually by runtime PM.
This patch tries to address the issue. It gives two things:
- implement the separate reboot_notify hook to struct alc_spec, and
call it optionally if defined.
- turn off the codec to D3 for Thinkpad models via this new callback
It seems that a workaround for Thinkpad T440s crackling noise can be
applied generically to all Thinkpad models: namely, disabling the
default alc269 shutup callback. This patch moves it to the existing
alc_fixup_tpt440_dock() while also replacing the rest code with
another existing alc_fixup_disable_aamix(). It resulted in a good
code reduction.
Apply the same fixup for Thinkpad with dock to Thinkpad X1 Carbon 2nd,
too. This reduces the annoying loud cracking noise problem, as well
as the support of missing docking port.
Lenovo Thinkpad T440s suffers from constant background noises, and it
seems to be a generic hardware issue on this model:
https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/T440s-speaker-noise/td-p/1339883
As the noise comes from the analog loopback path, disabling the path
is the easy workaround.
Also, the machine gives significant cracking noises at PM suspend. A
workaround found by trial-and-error is to disable the shutup callback
currently used for ALC269-variant.
This patch addresses these noise issues by introducing a new fixup
chain. Although the same workaround might be applicable to other
Thinkpad models, it's applied only to T440s (17aa:220c) in this patch,
so far, just to be safe (you chicken!). As a compromise, a new model
option string "tp440" is provided now, though, so that owners of other
Thinkpad models can test it more easily.
We have two latest thinkpad laptop models which are all based on the
Intel skylake platforms, and all of them have the codec alc293 on
them. When the machines boot to the desktop, an greeting dialogue
shows up with the notification sound. But on these two models, there
is noise with the notification sound. We have 3 SKUs for each of
the models, all of them have this problem.
So far, this problem is only specific to these two thinkpad models,
we did not find this problem on the old thinkpad models with the
codec alc293 or alc292.
A workaround for this problem is disabling the aamix.
rme96 driver needs to reset DAC depending on the sample rate, and this
results in resetting to the max volume suddenly. It's because of the
missing call of snd_rme96_apply_dac_volume().
However, calling this function right after the DAC reset still may not
work, and we need some delay before this call. Since the DAC reset
and the procedure after that are performed in the spinlock, we delay
the DAC volume restore at the end after the spinlock.
The recent addition of ELD notifier for Intel HDMI/DP codec may lead
the bad codec connection found as kernel messages like below:
Suspending console(s) (use no_console_suspend to debug)
hdmi_present_sense: snd_hda_codec_hdmi hdaudioC0D2: HDMI status: Codec=2 Pin=6 Presence_Detect=1 ELD_Valid=1
snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f2e08
snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f2e08
....
snd_hda_codec_hdmi hdaudioC0D2: HDMI: ELD buf size is 0, force 128
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x206f2f00
snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x206f2f00
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to single_cmd mode: last cmd=0x206f2f00
azx_single_wait_for_response: 42 callbacks suppressed
This seems appearing when the sound driver went to suspend before i915
driver. Then i915 driver disables HDMI/DP audio bit and calls the
registered notifier, and the HDA codec tries to handle it as a
hot(un)plug. But since the driver is already in the suspended state,
it fails miserably.
As this is a sort of spurious wakeup, it can be ignored safely, as
long as it's delivered during the system suspend. OTOH, if a
notification comes during the runtime suspend, the situation is
different: we need to wake up. But during the system suspend, such a
notification can't be the reason for a wakeup.
This patch addresses it by a simple check of the current sound card
status. The skipped notification doesn't matter because the HDA
driver will check the plugged status forcibly at the resume in
return.
Then, why the card status, not a runtime PM status or else? The HDA
controller driver is supposed to set the card status to D3 at the
system suspend but not at the runtime suspend. So we can see it as a
flag that is set only for the system suspend. Admittedly, it's a bit
ugly, but it should work well for now.
Reported-and-tested-by: "Zhang, Xiong Y" <xiong.y.zhang@intel.com> Fixes: 25adc137c546 ('ALSA: hda - Wake the codec up on pin/ELD notify events') Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gigabyte Z710X mobo with ALC1150 codec gets significant noises from
the analog loopback routes even if their inputs are all muted.
Simply kill the aamix for fixing it.
For making the speakers on Acer Aspire One Cloudbook 14 to work, we
need the as same quirk as for another Chromebook. This patch adds the
corresponding fixup entry.
Dell Latitude E6440 (1028:05bd) needs the same fixup as applied to
other Latitude E7xxx models for the click noise due to the recent
power-saving changes.
It turned out that many HP laptops suffer from the same problem as
fixed in commit [c932b98c1e47: ALSA: hda - Apply pin fixup for HP
ProBook 6550b]. But, it's tiresome to list up all such PCI SSIDs, as
there are really lots of HP machines.
Instead, we do a bit more clever, try to check the supposedly dock and
built-in headphone pins, and apply the fixup when both seem valid.
This rule can be applied generically to all models using the same
quirk, so we'll fix all in a shot.
When committed to upstream, these four modules had wrong entries for
Makefile. This forces them to be loadable modules even if they're set
as built-in.
This commit fixes this bug.
Fixes: b5b04336015e('ALSA: fireworks: Add skelton for Fireworks based devices') Fixes: fd6f4b0dc167('ALSA: bebob: Add skelton for BeBoB based devices') Fixes: 1a4e39c2e5ca('ALSA: oxfw: Move to its own directory') Fixes: 14ff6a094815('ALSA: dice: Move file to its own directory') Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HP ProBook 6550b needs the same pin fixup applied to other HP B-series
laptops with docks for making its headphone and dock headphone jacks
working properly. We just need to add the codec SSID to the list.
During the migration to HDA core code, we lost the workaround for 4k
BDL boundary. The flag exists in the new hdac_bus, but it's never
set. This resulted in the sudden sound stall on some controllers that
require this workaround like Creative Recon3D.
This patch fixes the issue by setting the flag for such controllers
properly.
We've had many reports that some Creative sound cards with CA0132
don't work well. Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used. All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.
This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries. I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.
Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too. So
the flag is applied to all Creative entries.
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
The timer and thread were not being started for internal messages,
so in interrupt mode if something hung the timer would never go
off and clean things up. Factor out the internal message sending
and start the timer for those messages, too.
Regardless of the previous CPU a timer was on, add_timer_on()
currently simply sets timer->flags to the new CPU. As the caller must
be seeing the timer as idle, this is locally fine, but the timer
leaving the old base while unlocked can lead to race conditions as
follows.
Let's say timer was on cpu 0.
cpu 0 cpu 1
-----------------------------------------------------------------------------
del_timer(timer) succeeds
del_timer(timer)
lock_timer_base(timer) locks cpu_0_base
add_timer_on(timer, 1)
spin_lock(&cpu_1_base->lock)
timer->flags set to cpu_1_base
operates on @timer operates on @timer
This triggered with mod_delayed_work_on() which contains
"if (del_timer()) add_timer_on()" sequence eventually leading to the
following oops.
When switch_mm() activates a new PGD, it also sets a bit that
tells other CPUs that the PGD is in use so that TLB flush IPIs
will be sent. In order for that to work correctly, the bit
needs to be visible prior to loading the PGD and therefore
starting to fill the local TLB.
Document all the barriers that make this work correctly and add
a couple that were missing.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When decompressing kernel image during x86 bootup, malloc memory
for ELF program headers may run out of heap space, which leads
to system halt. This patch doubles BOOT_HEAP_SIZE to 64KB.
Tested with 32-bit kernel which failed to boot without this patch.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we do not do this, it is not properly saved and restored across
migration. Windows notices due to its self-protection mechanisms,
and is very upset about it (blue screen of death).
Currently it is possible for userspace (e.g. QEMU) to set a value
for the MSR for a guest VCPU which has both of the TS bits set,
which is an illegal combination. The result of this is that when
we execute a hrfid (hypervisor return from interrupt doubleword)
instruction to enter the guest, the CPU will take a TM Bad Thing
type of program interrupt (vector 0x700).
Now, if PR KVM is configured in the kernel along with HV KVM, we
actually handle this without crashing the host or giving hypervisor
privilege to the guest; instead what happens is that we deliver a
program interrupt to the guest, with SRR0 reflecting the address
of the hrfid instruction and SRR1 containing the MSR value at that
point. If PR KVM is not configured in the kernel, then we try to
run the host's program interrupt handler with the MMU set to the
guest context, which almost certainly causes a host crash.
This closes the hole by making kvmppc_set_msr_hv() check for the
illegal combination and force the TS field to a safe value (00,
meaning non-transactional).
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In static micro-threading modes, the dynamic micro-threading code
is supposed to be disabled, because subcores can't make independent
decisions about what micro-threading mode to put the core in - there is
only one micro-threading mode for the whole core. The code that
implements dynamic micro-threading checks for this, except that the
check was missed in one case. This means that it is possible for a
subcore in static 2-way micro-threading mode to try to put the core
into 4-way micro-threading mode, which usually leads to stuck CPUs,
spinlock lockups, and other stalls in the host.
The problem was in the can_split_piggybacked_subcores() function, which
should always return false if the system is in a static micro-threading
mode. This fixes the problem by making can_split_piggybacked_subcores()
use subcore_config_ok() for its checks, as subcore_config_ok() includes
the necessary check for the static micro-threading modes.
Credit to Gautham Shenoy for working out that the reason for the hangs
and stalls we were seeing was that we were trying to do dynamic 4-way
micro-threading while we were in static 2-way mode.
Fixes: b4deba5c41e9 Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a cancelled suspend the vcpu_info location does not change (it's
still in the per-cpu area registered by xen_vcpu_setup()). So do not
call xen_hvm_init_shared_info() which would make the kernel think its
back in the shared info. With the wrong vcpu_info, events cannot be
received and the domain will hang after a cancelled suspend.
Signed-off-by: Charles Ouyang <ouyangzhaowei@huawei.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
