ipv6_find_hdr() does not validate that this is an IPv6 packet. Add a
sanity check for calling ipv6_find_hdr() to make sure an IPv6 packet
is passed for parsing.
The mlx5_ib_bind_slave_port() doesn't remove multiport device from the
unaffiliated list, but mlx5_ib_unbind_slave_port() did it. This unbalanced
flow caused to the situation where mlx5_ib_unaffiliated_port_list was
changed during iteration.
Fixes: 63c416887437 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the code execute this if statement, the value of ret is 0.
However, we can see from the ath10k_warn() log that the value of
ret should be -EINVAL.
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: ccec9038c721 ("ath10k: enable raw encap mode and software crypto engine") Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1621939577-62218-1-git-send-email-yang.lee@linux.alibaba.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The rx_lastpkt_rssi field provided by the firmware is suitable for
NL80211_STA_INFO_{SIGNAL,CHAIN_SIGNAL}, while the rssi field is an
average. Fix up the assignments and set the correct STA_INFO bits. This
lets userspace know that the average RSSI is part of the station info.
Fixes: cae355dc90db ("brcmfmac: Add RSSI information to get_station.") Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210506132010.3964484-2-alsi@bang-olufsen.dk Signed-off-by: Sasha Levin <sashal@kernel.org>
The sinfo->chains field is a bitmask for filled values in chain_signal
and chain_signal_avg, not a count. Treat it as such so that the driver
can properly report per-chain RSSI information.
Before (MIMO mode):
$ iw dev wlan0 station dump
...
signal: -51 [-51] dBm
After (MIMO mode):
$ iw dev wlan0 station dump
...
signal: -53 [-53, -54] dBm
Fixes: cae355dc90db ("brcmfmac: Add RSSI information to get_station.") Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210506132010.3964484-1-alsi@bang-olufsen.dk Signed-off-by: Sasha Levin <sashal@kernel.org>
Right now wcn->hal_buf is allocated in wcn36xx_start(). This is a problem
since we should have setup all of the buffers we required by the time
ieee80211_register_hw() is called.
struct ieee80211_ops callbacks may run prior to mac_start() and therefore
wcn->hal_buf must be initialized.
This is easily remediated by moving the allocation to probe() taking the
opportunity to tidy up freeing memory by using devm_kmalloc().
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210605173347.2266003-1-bryan.odonoghue@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
In hwsim_subscribe_all_others, the error handling code performs
incorrectly if the second hwsim_alloc_edge fails. When this issue occurs,
it goes to sub_fail, without cleaning the edges allocated before.
Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20210611015812.1626999-1-mudongliangabcd@gmail.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kernel test robot reports over 200 build errors and warnings
that are due to this Kconfig problem when CARL9170=m,
MAC80211=y, and LEDS_CLASS=m.
WARNING: unmet direct dependencies detected for MAC80211_LEDS
Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y])
Selected by [m]:
- CARL9170_LEDS [=y] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && CARL9170 [=m]
CARL9170_LEDS selects MAC80211_LEDS even though its kconfig
dependencies are not met. This happens because 'select' does not follow
any Kconfig dependency chains.
Fix this by making CARL9170_LEDS depend on MAC80211_LEDS, where
the latter supplies any needed dependencies on LEDS_CLASS.
Fixes: 1d7e1e6b1b8ed ("carl9170: Makefile, Kconfig files and MAINTAINERS") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: linux-wireless@vger.kernel.org Cc: Arnd Bergmann <arnd@arndb.de> Suggested-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210530031134.23274-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The object surf is not fully initialized and the uninitialized
field surf.data is being copied by the call to qxl_bo_create
via the call to qxl_gem_object_create. Set surf.data to zero
to ensure garbage data from the stack is not being copied.
To avoid the following failure when trying to load the rdma_rxe module
while IPv6 is disabled, add a check for EAFNOSUPPORT and ignore the
failure, also delete the needless debug print from rxe_setup_udp_tunnel().
$ modprobe rdma_rxe
modprobe: ERROR: could not insert 'rdma_rxe': Operation not permitted
Fixes: dfdd6158ca2c ("IB/rxe: Fix kernel panic in udp_setup_tunnel") Link: https://lore.kernel.org/r/20210603090112.36341-1-kamalheib1@gmail.com Reported-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Kamal Heib <kamalheib1@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In each iteration fwnode_for_each_available_child_node() bumps a reference
counting of a loop variable followed by dropping in on a next iteration,
Since in error case the loop is broken, we have to drop a reference count
by ourselves. Do it for port_fwnode in error case during ->probe().
Fixes: 248122212f68 ("net: mvpp2: use device_*/fwnode_* APIs instead of of_*") Cc: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The snprintf() function returns the number of bytes which would have been
printed if the buffer was large enough. In other words it can return ">=
remain" but this code assumes it returns "== remain".
The run time impact of this bug is not very severe. The next iteration
through the loop would trigger a WARN() when we pass a negative limit to
snprintf(). We would then return success instead of -E2BIG.
The kernel implementation of snprintf() will never return negatives so
there is no need to check and I have deleted that dead code.
Link: https://lkml.kernel.org/r/20210511135350.GV1955@kadam Fixes: a860f6eb4c6a ("ocfs2: sysfile interfaces for online file check") Fixes: 74ae4e104dfc ("ocfs2: Create stack glue sysfs files.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit a79050434b45 ("blk-rq-qos: refactor out common elements of
blk-wbt"), if throttle was disabled by wbt_disable_default(), we could
not enable again, fix this by set enable_state back to
WBT_STATE_ON_DEFAULT.
Fixes: a79050434b45 ("blk-rq-qos: refactor out common elements of blk-wbt") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Link: https://lore.kernel.org/r/20210619093700.920393-3-yi.zhang@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Now that we disable wbt by simply zero out rwb->wb_normal in
wbt_disable_default() when switch elevator to bfq, but it's not safe
because it will become false positive if we change queue depth. If it
become false positive between wbt_wait() and wbt_track() when submit
write request, it will lead to drop rqw->inflight to -1 in wbt_done(),
which will end up trigger IO hung. Fix this issue by introduce a new
state which mean the wbt was disabled.
Fixes: a79050434b45 ("blk-rq-qos: refactor out common elements of blk-wbt") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Link: https://lore.kernel.org/r/20210619093700.920393-2-yi.zhang@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, a device description can be obtained using ACPI, if the _STR
method exists for a particular device, and then exposed to the userspace
via a sysfs object as a string value.
If the _STR method is available for a given device then the data
(usually a Unicode string) is read and stored in a buffer (of the
ACPI_TYPE_BUFFER type) with a pointer to said buffer cached in the
struct acpi_device_pnp for later access.
The description_show() function is responsible for exposing the device
description to the userspace via a corresponding sysfs object and
internally calls the utf16s_to_utf8s() function with a pointer to the
buffer that contains the Unicode string so that it can be converted from
UTF16 encoding to UTF8 and thus allowing for the value to be safely
stored and later displayed.
When invoking the utf16s_to_utf8s() function, the description_show()
function also sets a limit of the data that can be saved into a provided
buffer as a result of the character conversion to be a total of
PAGE_SIZE, and upon completion, the utf16s_to_utf8s() function returns
an integer value denoting the number of bytes that have been written
into the provided buffer.
Following the execution of the utf16s_to_utf8s() a newline character
will be added at the end of the resulting buffer so that when the value
is read in the userspace through the sysfs object then it would include
newline making it more accessible when working with the sysfs file
system in the shell, etc. Normally, this wouldn't be a problem, but if
the function utf16s_to_utf8s() happens to return the number of bytes
written to be precisely PAGE_SIZE, then we would overrun the buffer and
write the newline character outside the allotted space which can have
undefined consequences or result in a failure.
To fix this buffer overrun, ensure that there always is enough space
left for the newline character to be safely appended.
Fixes: d1efe3c324ea ("ACPI: Add new sysfs interface to export device description") Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function nx842_OF_upd_status triggers a sparse RCU warning when
it directly dereferences the RCU-protected devdata. This appears
to be an accident as there was another variable of the same name
that was passed in from the caller.
After it was removed (because the main purpose of using it, to
update the status member was itself removed) the global variable
unintenionally stood in as its replacement.
The current sun6i SPI implementation initializes the transfer too early,
resulting in SCK going high before the transfer. When using an additional
(gpio) chipselect with sun6i, the chipselect is asserted at a time when
clock is high, making the SPI transfer fail.
This is due to SUN6I_GBL_CTL_BUS_ENABLE being written into
SUN6I_GBL_CTL_REG at an early stage. Moving that to the transfer
function, hence, right before the transfer starts, mitigates that
problem.
When a log recovery is in progress, lots of operations have to take that
into account, so we keep this status per tree during the operation. Long
time ago error handling revamp patch 79787eaab461 ("btrfs: replace many
BUG_ONs with proper error handling") removed clearing of the status in
an error branch. Add it back as was intended in e02119d5a7b4 ("Btrfs:
Add a write ahead tree log to optimize synchronous operations").
There are probably no visible effects, log replay is done only during
mount and if it fails all structures are cleared so the stale status
won't be kept.
Fixes: 79787eaab461 ("btrfs: replace many BUG_ONs with proper error handling") Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fans 7..12 do not have their own set of configuration registers.
So far the code ignored that and read beyond the end of the configuration
register range to get the tachometer period. This resulted in more or less
random fan speed values for those fans.
The datasheet is quite vague when it comes to defining the tachometer
period for fans 7..12. Experiments confirm that the period is the same
for both fans associated with a given set of configuration registers.
Fixes: 54187ff9d766 ("hwmon: (max31790) Convert to use new hwmon registration API") Fixes: 195a4b4298a7 ("hwmon: Driver for Maxim MAX31790") Cc: Jan Kundrát <jan.kundrat@cesnet.cz> Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Václav Kubernát <kubernat@cesnet.cz> Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20210526154022.3223012-2-linux@roeck-us.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Valid Maxim Integrated ACPI device IDs would start with MXIM,
not with MAX1. On top of that, ACPI device IDs reflecting chip names
are almost always invalid.
Remove the invalid ACPI IDs.
Fixes: 04e1e70afec6 ("hwmon: (max31722) Add support for MAX31722/MAX31723 temperature sensors") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rename struct sms_msg_data4 to sms_msg_data5 and increase the size of
its msg_data array from 4 to 5 elements. Notice that at some point
the 5th element of msg_data is being accessed in function
smscore_load_firmware_family2():
1006 trigger_msg->msg_data[4] = 4; /* Task ID */
Also, there is no need for the object _trigger_msg_ of type struct
sms_msg_data *, when _msg_ can be used, directly. Notice that msg_data
in struct sms_msg_data is a one-element array, which causes multiple
out-of-bounds warnings when accessing beyond its first element
in function smscore_load_firmware_family2():
the out-of-bounds warnings are actually valid and should be addressed.
Fix this by declaring object _msg_ of type struct sms_msg_data5 *,
which contains a 5-elements array, instead of just 4. And use
_msg_ directly, instead of creating object trigger_msg.
This helps with the ongoing efforts to enable -Warray-bounds by fixing
the following warnings:
CC [M] drivers/media/common/siano/smscoreapi.o
drivers/media/common/siano/smscoreapi.c: In function ‘smscore_load_firmware_family2’:
drivers/media/common/siano/smscoreapi.c:1003:24: warning: array subscript 1 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1003 | trigger_msg->msg_data[1] = 6; /* Priority */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1004:24: warning: array subscript 2 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1004 | trigger_msg->msg_data[2] = 0x200; /* Stack size */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1005:24: warning: array subscript 3 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1005 | trigger_msg->msg_data[3] = 0; /* Parameter */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1006:24: warning: array subscript 4 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1006 | trigger_msg->msg_data[4] = 4; /* Task ID */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
Fixes: 018b0c6f8acb ("[media] siano: make load firmware logic to work with newer firmwares") Co-developed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the gl860_RTx() helper so that zero-length control reads fail with
an error message instead. Note that there are no current callers that
would trigger this.
Fixes: 4f7cb8837cec ("V4L/DVB (12954): gspca - gl860: Addition of GL860 based webcams") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the CSI bps per lane is not in the valid range, an appropriate error
code -EINVAL should be returned. However, we currently do not explicitly
assign this error code to 'ret'. As a result, 0 was incorrectly returned.
Fixes: 256148246852 ("[media] tc358743: support probe from device tree") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In isp_video_release, file->private_data is freed via
_vb2_fop_release()->v4l2_fh_release(). But the freed
file->private_data is still used in v4l2_fh_is_singular_file()
->v4l2_fh_is_singular(file->private_data), which is a use
after free bug.
My patch uses a variable 'is_singular_file' to avoid the uaf.
v3: https://lore.kernel.org/patchwork/patch/1419058/
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Propagate the error code
upstream, as it should have been done from the start...
'ret' is known to be 1 here. In fact 'i' is expected instead.
Store the return value of 'i2c_master_recv()' in 'ret' so that the error
message print the correct error code.
EVM_SETUP_COMPLETE is defined as 0x80000000, which is larger than INT_MAX.
The "-fno-strict-overflow" compiler option properly prevents signaling
EVM that the EVM policy setup is complete. Define and read an unsigned
int.
Fixes: f00d79750712 ("EVM: Allow userspace to signal an RSA key has been loaded") Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Iff platform_get_irq() fails (or returns IRQ0) and thus the polling mode
has to be used, ata_host_activate() hits the WARN_ON() due to 'irq_handler'
parameter being non-NULL if the polling mode is selected. Let's only set
the pointer to the driver's IRQ handler if platform_get_irq() returns a
valid IRQ # -- this should avoid the unnecessary WARN_ON()...
The use of an enum named 'RST' conflicts with a #define macro
named 'RST' in arch/mips/include/asm/mach-rc32434/rb.h.
The MIPS use of RST was there first (AFAICT), so change the
media/i2c/ uses of RST to be named 'RSET'.
'git grep -w RSET' does not report any naming conflicts with the
new name.
This fixes multiple build errors:
arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
drivers/media/i2c/s5c73m3/s5c73m3.h:356:2: note: in expansion of macro 'RST'
356 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k6aa.c:180:2: note: in expansion of macro 'RST'
180 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k5baf.c:238:2: note: in expansion of macro 'RST'
238 | RST,
| ^~~
and some others that I have trimmed.
Fixes: cac47f1822fc ("[media] V4L: Add S5C73M3 camera driver") Fixes: 8b99312b7214 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor") Fixes: 7d459937dc09 ("[media] Add driver for Samsung S5K5BAF camera sensor") Fixes: bfa8dd3a0524 ("[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENOENT, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Testing ixp4xx_crypto with CONFIG_DMA_API_DEBUG lead to the following error:
DMA-API: platform ixp4xx_crypto.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=24 bytes]
There's a bug at s5p_cec_adap_enable(): if called to
disable the device, it should call pm_runtime_put()
instead of pm_runtime_disable(), as the goal here is to
decrement the usage_count and not to disable PM runtime.
gcc points out a mistake in the mca driver that goes back to before the
git history:
arch/ia64/kernel/mca_drv.c: In function 'init_record_index_pools':
arch/ia64/kernel/mca_drv.c:346:54: error: expression does not compute the number of elements in this array; element typ
e is 'int', not 'size_t' {aka 'long unsigned int'} [-Werror=sizeof-array-div]
346 | for (i = 1; i < sizeof sal_log_sect_min_sizes/sizeof(size_t); i++)
| ^
This is the same as sizeof(size_t), which is two shorter than the actual
array. Use the ARRAY_SIZE() macro to get the correct calculation instead.
A custom DSDT file is mostly used during development or debugging,
and in that case it is quite likely to want to rebuild the kernel
after changing ONLY the content of the DSDT.
This patch adds the custom DSDT as a prerequisite to tables.o
to ensure a rebuild if the DSDT file is updated. Make will merge
the prerequisites from multiple rules for the same target.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the clocksource watchdog marks a clock as unstable, this might be due
to that clock being unstable or it might be due to delays that happen to
occur between the reads of the two clocks. Yes, interrupts are disabled
across those two reads, but there are no shortage of things that can delay
interrupts-disabled regions of code ranging from SMI handlers to vCPU
preemption. It would be good to have some indication as to why the clock
was marked unstable.
Therefore, re-read the watchdog clock on either side of the read from the
clock under test. If the watchdog clock shows an excessive time delta
between its pair of reads, the reads are retried.
The maximum number of retries is specified by a new kernel boot parameter
clocksource.max_cswd_read_retries, which defaults to three, that is, up to
four reads, one initial and up to three retries. If more than one retry
was required, a message is printed on the console (the occasional single
retry is expected behavior, especially in guest OSes). If the maximum
number of retries is exceeded, the clock under test will be marked
unstable. However, the probability of this happening due to various sorts
of delays is quite small. In addition, the reason (clock-read delays) for
the unstable marking will be apparent.
Reported-by: Chris Mason <clm@fb.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Feng Tang <feng.tang@intel.com> Link: https://lore.kernel.org/r/20210527190124.440372-1-paulmck@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Although the system will not be in a good condition or it will not
boot if acpi_bus_init() fails, it is still necessary to put the
kobject in the error path before returning to avoid leaking memory.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the ACPI spec, _CID returns a package containing
hardware ID's. Each element of an ASL package contains a reference
count from the parent package as well as the element itself.
Name (TEST, Package() {
"String object" // this package element has a reference count of 2
})
A memory leak was caused in the _CID repair function because it did
not decrement the reference count created by the package. Fix the
memory leak by calling acpi_ut_remove_reference on _CID package elements
that represent a hardware ID (_HID).
Link: https://github.com/acpica/acpica/commit/180cb539 Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I got some kmemleak report when a node was fenced. The user space tool
dlm_controld will therefore run some rmdir() in dlm configfs which was
triggering some memleaks. This patch stores the sps and cms attributes
which stores some handling for subdirectories of the configfs cluster
entry and free them if they get released as the parent directory gets
freed.
include/linux/prandom.h:114:45: sparse: sparse: cast truncates bits from
constant value
This is because the 64-bit seed value is manipulated and then placed in a
u32, causing an implicit cast and truncation. A forced cast to u32 doesn't
prevent this warning, which is reasonable because a typecast doesn't prove
that truncation was expected.
Logical-AND the value with 0xffffffff to make explicit that truncation to
32-bit is intended.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20210525122012.6336-3-rf@opensource.cirrus.com Signed-off-by: Sasha Levin <sashal@kernel.org>
These rx tx flags arguments are for signaling close_connection() from
which worker they are called. Obviously the receive worker cannot cancel
itself and vice versa for swork. For the othercon the receive worker
should only be used, however to avoid deadlocks we should pass the same
flags as the original close_connection() was called.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
block_dump is an old debugging interface, one of it's functions is used
to print the information about who write which file on disk. If we
enable block_dump through /proc/sys/vm/block_dump and turn on debug log
level, we can gather information about write process name, target file
name and disk from kernel message. This feature is realized in
block_dump___mark_inode_dirty(), it print above information into kernel
message directly when marking inode dirty, so it is noisy and can easily
trigger log storm. At the same time, get the dentry refcount is also not
safe, we found it will lead to deadlock on ext4 file system with
data=journal mode.
After tracepoints has been introduced into the kernel, we got a
tracepoint in __mark_inode_dirty(), which is a better replacement of
block_dump___mark_inode_dirty(). The only downside is that it only trace
the inode number and not a file name, but it probably doesn't matter
because the original printed file name in block_dump is not accurate in
some cases, and we can still find it through the inode number and device
id. So this patch delete the dirting inode part of block_dump feature.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20210313030146.2882027-2-yi.zhang@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
More ASUS laptops have the _GPE define in the DSDT table with a
different value than the _GPE number in the ECDT.
This is causing media keys not working on ASUS X505BA/BP, X542BA/BP
Add model info to the quirks list.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com> Signed-off-by: Jian-Hong Pan <jhp@endlessos.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing code attempted to handle numbers by doing a strto[u]l(),
ignoring the field width, and then repeatedly dividing to extract the
field out of the full converted value. If the string contains a run of
valid digits longer than will fit in a long or long long, this would
overflow and no amount of dividing can recover the correct value.
This patch fixes vsscanf() to obey number field widths when parsing
the number.
A new _parse_integer_limit() is added that takes a limit for the number
of characters to parse. The number field conversion in vsscanf is changed
to use this new function.
If a number starts with a radix prefix, the field width must be long
enough for at last one digit after the prefix. If not, it will be handled
like this:
sscanf("0x4", "%1i", &i): i=0, scanning continues with the 'x'
sscanf("0x4", "%2i", &i): i=0, scanning continues with the '4'
This is consistent with the observed behaviour of userland sscanf.
Note that this patch does NOT fix the problem of a single field value
overflowing the target type. So for example:
Generally, the C-state latency is provided by the _CST method or
FADT, but some OEM platforms using AMD Picasso, Renoir, Van Gogh,
and Cezanne set the C2 latency greater than C3's which causes the
C2 state to be skipped.
That will block the core entering PC6, which prevents S0ix working
properly on Linux systems.
In other operating systems, the latency values are not validated and
this does not cause problems by skipping states.
To avoid this issue on Linux, detect when latencies are not an
arithmetic progression and sort them.
Action of unbinding driver from a device is not cancellable and should not
fail, and driver core does not pay attention to the result of "remove"
method, therefore using down_interruptible() in hid_device_remove() does
not make sense.
With a config having PAGE_SIZE set to 256K, BTRFS build fails
with the following message
include/linux/compiler_types.h:326:38: error: call to
'__compiletime_assert_791' declared with attribute error:
BUILD_BUG_ON failed: (BTRFS_MAX_COMPRESSED % PAGE_SIZE) != 0
BTRFS_MAX_COMPRESSED being 128K, BTRFS cannot support platforms with
256K pages at the time being.
There are two platforms that can select 256K pages:
- hexagon
- powerpc
Disable BTRFS when 256K page size is selected. Supporting this would
require changes to the subpage mode that's currently being developed.
Given that 256K is many times larger than page sizes commonly used and
for what the algorithms and structures have been tuned, it's out of
scope and disabling build is a reasonable option.
If we fail to update the delayed inode we need to abort the transaction,
because we could leave an inode with the improper counts or some other
such corruption behind.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we get an error while looking up the inode item we'll simply bail
without cleaning up the delayed node. This results in this style of
warning happening on commit:
Because the iref isn't dropped and this leaves an elevated node->count,
so any release just re-queues it onto the delayed inodes list. Fix this
by going to the out label to handle the proper cleanup of the delayed
node.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some BT.656 sensors (e.g. ADV718x) transmit frames with unstable BT.656
sync codes after initial power on. This confuses the imx CSI,resulting
in vertical and/or horizontal sync issues. Skip the first 20 frames
to avoid the unstable sync codes.
[fabio: fixed checkpatch warning and increased the frame skipping to 20]
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The risk of especulation is actually almost-non-existing here,
as there are very few users of TCP/IP using the DVB stack,
as, this is mainly used with DVB-S/S2 cards, and only by people
that receives TCP/IP from satellite connections, which limits
a lot the number of users of such feature(*).
(*) In thesis, DVB-C cards could also benefit from it, but I'm
yet to see a hardware that supports it.
crypto_shash_alg_has_setkey() is implemented by testing whether the
.setkey() member of a struct shash_alg points to the default version,
called shash_no_setkey(). As crypto_shash_alg_has_setkey() is a static
inline, this requires shash_no_setkey() to be exported to modules.
Unfortunately, when building with CFI, function pointers are routed
via CFI stubs which are private to each module (or to the kernel proper)
and so this function pointer comparison may fail spuriously.
Let's fix this by turning crypto_shash_alg_has_setkey() into an out of
line function.
Cc: Sami Tolvanen <samitolvanen@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the driver fails to talk with the hardware with dvb_usb_generic_rw,
it will return an error to dvb_usb_adapter_frontend_init. However, the
driver forgets to free the resource (e.g., struct cinergyt2_fe_state),
which leads to a memory leak.
Fix this by freeing struct cinergyt2_fe_state when dvb_usb_generic_rw
fails in cinergyt2_frontend_attach.
When ctx_id >= HVA_MAX_INSTANCES in hva_hw_its_irq_thread() it tries to
access fields of ctx that is NULL at that point. The patch gets rid of
these accesses.
Found by Linux Driver Verification project (linuxtesting.org).
In 'bt878_irq', the driver calls 'tasklet_schedule', but this tasklet is
set in 'dvb_bt8xx_load_card' of another driver 'dvb-bt8xx'.
However, this two drivers are separate. The user may not load the
'dvb-bt8xx' driver when loading the 'bt8xx' driver, that is, the tasklet
has not been initialized when 'tasklet_schedule' is called, so it is
necessary to check whether the tasklet is initialized in 'bt878_probe'.
Fix this by adding a check at the end of bt878_probe.
When using something other than 8 spaces per tab, this ascii art
makes not sense, and the reader might end up wondering what this
advanced equation "is".
Signed-off-by: Odin Ugedal <odin@uged.al> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/20210518125202.78658-4-odin@uged.al Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot has reported the following warning in pvr2_i2c_done:
sysfs group 'power' not found for kobject '1-0043'
When the device is disconnected (pvr_hdw_disconnect), the i2c adapter is
not unregistered along with the USB and v4l2 teardown. As part of the USB
device disconnect, the sysfs files of the subdevices are also deleted.
So, by the time pvr_i2c_core_done is called by pvr_context_destroy, the
sysfs files have been deleted.
To fix this, unregister the i2c adapter too in pvr_hdw_disconnect. Make
the device deregistration code shared by calling pvr_hdw_disconnect from
pvr2_hdw_destroy.
syzbot reported leak in cpia2 usb driver. The problem was
in invalid error handling.
v4l2_device_register() is called in cpia2_init_camera_struct(), but
all error cases after cpia2_init_camera_struct() did not call the
v4l2_device_unregister()
Reported-by: syzbot+d1e69c888f0d3866ead4@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for
data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will
free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after
kfree() to avoid double free.
Currently, the SPI core doesn't set the struct device fwnode pointer
when it creates a new SPI device. This means when the device is
registered the fwnode is NULL and the check in device_add which sets
the fwnode->dev pointer is skipped. This wasn't previously an issue,
however these two patches:
commit 4731210c09f5 ("gpiolib: Bind gpio_device to a driver to enable
fw_devlink=on by default")
commit ced2af419528 ("gpiolib: Don't probe gpio_device if it's not the
primary device")
Added some code to the GPIO core which relies on using that
fwnode->dev pointer to determine if a driver is bound to the fwnode
and if not bind a stub GPIO driver. This means the GPIO providers
behind SPI will get both the expected driver and this stub driver
causing the stub driver to fail if it attempts to request any pin
configuration. For example on my system:
madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3
madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl
gpio_stub_drv gpiochip3: Error applying setting, reverse things back
gpio_stub_drv: probe of gpiochip3 failed with error -22
The firmware node on the device created by the GPIO framework is set
through the of_node pointer hence things generally actually work,
however that fwnode->dev is never set, as the check was skipped at
device_add time. This fix appears to match how the I2C subsystem
handles the same situation.
A request could end up on the fpq->io list after fuse_abort_conn() has
reset fpq->connected and aborted requests on that list:
Thread-1 Thread-2
======== ========
->fuse_simple_request() ->shutdown
->__fuse_request_send()
->queue_request() ->fuse_abort_conn()
->fuse_dev_do_read() ->acquire(fpq->lock)
->wait_for(fpq->lock) ->set err to all req's in fpq->io
->release(fpq->lock)
->acquire(fpq->lock)
->add req to fpq->io
After the userspace copy is done the request will be ended, but
req->out.h.error will remain uninitialized. Also the copy might block
despite being already aborted.
Fix both issues by not allowing the request to be queued on the fpq->io
list after fuse_abort_conn() has processed this list.
Reported-by: Pradeep P V K <pragalla@codeaurora.org> Fixes: fd22d62ed0c3 ("fuse: no fc->lock for iqueue parts") Cc: <stable@vger.kernel.org> # v4.2 Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EVM_ALLOW_METADATA_WRITES is an EVM initialization flag that can be set to
temporarily disable metadata verification until all xattrs/attrs necessary
to verify an EVM portable signature are copied to the file. This flag is
cleared when EVM is initialized with an HMAC key, to avoid that the HMAC is
calculated on unverified xattrs/attrs.
Currently EVM unnecessarily denies setting this flag if EVM is initialized
with a public key, which is not a concern as it cannot be used to trust
xattrs/attrs updates. This patch removes this limitation.
evm_inode_init_security() requires an HMAC key to calculate the HMAC on
initial xattrs provided by LSMs. However, it checks generically whether a
key has been loaded, including also public keys, which is not correct as
public keys are not suitable to calculate the HMAC.
Originally, support for signature verification was introduced to verify a
possibly immutable initial ram disk, when no new files are created, and to
switch to HMAC for the root filesystem. By that time, an HMAC key should
have been loaded and usable to calculate HMACs for new files.
More recently support for requiring an HMAC key was removed from the
kernel, so that signature verification can be used alone. Since this is a
legitimate use case, evm_inode_init_security() should not return an error
when no HMAC key has been loaded.
This patch fixes this problem by replacing the evm_key_loaded() check with
a check of the EVM_INIT_HMAC flag in evm_initialized.
In raise_backtrace_ipi() we iterate through the cpumask of CPUs, sending
each an IPI asking them to do a backtrace, but we don't wait for the
backtrace to happen.
We then iterate through the CPU mask again, and if any CPU hasn't done
the backtrace and cleared itself from the mask, we print a trace on its
behalf, noting that the trace may be "stale".
This works well enough when a CPU is not responding, because in that
case it doesn't receive the IPI and the sending CPU is left to print the
trace. But when all CPUs are responding we are left with a race between
the sending and receiving CPUs, if the sending CPU wins the race then it
will erroneously print a trace.
This leads to spurious "stale" traces from the sending CPU, which can
then be interleaved messily with the receiving CPU, note the CPU
numbers, eg:
[ 1658.929157][ C7] rcu: Stack dump where RCU GP kthread last ran:
[ 1658.929223][ C7] Sending NMI from CPU 7 to CPUs 1:
[ 1658.929303][ C1] NMI backtrace for cpu 1
[ 1658.929303][ C7] CPU 1 didn't respond to backtrace IPI, inspecting paca.
[ 1658.929362][ C1] CPU: 1 PID: 325 Comm: kworker/1:1H Tainted: G W E 5.13.0-rc2+ #46
[ 1658.929405][ C7] irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 325 (kworker/1:1H)
[ 1658.929465][ C1] Workqueue: events_highpri test_work_fn [test_lockup]
[ 1658.929549][ C7] Back trace of paca->saved_r1 (0xc0000000057fb400) (possibly stale):
[ 1658.929592][ C1] NIP: c00000000002cf50 LR: c008000000820178 CTR: c00000000002cfa0
To fix it, change the logic so that the sending CPU waits 5s for the
receiving CPU to print its trace. If the receiving CPU prints its trace
successfully then the sending CPU just continues, avoiding any spurious
"stale" trace.
This has the added benefit of allowing all CPUs to print their traces in
order and avoids any interleaving of their output.
Since the raw memory 'data' does not go forward, it will dump repeated
data if the data length is more than 8. If we want to dump longer data
blocks, we need to repeatedly call macro SEQ_PUT_HEX_FIELD. I think it
is a bit redundant, and multiple function calls also affect the performance.
All internal use cases for tracepoint_probe_register() is set to not ever
be called with the same function and data. If it is, it is considered a
bug, as that means the accounting of handling tracepoints is corrupted.
If the function and data for a tracepoint is already registered when
tracepoint_probe_register() is called, it will call WARN_ON_ONCE() and
return with EEXISTS.
The BPF system call can end up calling tracepoint_probe_register() with
the same data, which now means that this can trigger the warning because
of a user space process. As WARN_ON_ONCE() should not be called because
user space called a system call with bad data, there needs to be a way to
register a tracepoint without triggering a warning.
Enter tracepoint_probe_register_may_exist(), which can be called, but will
not cause a WARN_ON() if the probe already exists. It will still error out
with EEXIST, which will then be sent to the user space that performed the
BPF system call.
This keeps the previous testing for issues with other users of the
tracepoint code, while letting BPF call it with duplicated data and not
warn about it.
With the addition of simple mathematical operations (plus and minus), the
parsing of the "sym-offset" modifier broke, as it took the '-' part of the
"sym-offset" as a minus, and tried to break it up into a mathematical
operation of "field.sym - offset", in which case it failed to parse
(unless the event had a field called "offset").
Both .sym and .sym-offset modifiers should not be entered into
mathematical calculations anyway. If ".sym-offset" is found in the
modifier, then simply make it not an operation that can be calculated on.
Link: https://lkml.kernel.org/r/20210707110821.188ae255@oasis.local.home Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: stable@vger.kernel.org Fixes: 100719dcef447 ("tracing: Add simple expression support to hist triggers") Reviewed-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In AP mode WPA2-PSK connections were not established.
The reason was that the AP was sending the first message
of the 4 way handshake encrypted, even though no pairwise
key had (correctly) yet been set.
Encryption was enabled if the "security_enable" driver flag
was set and encryption was not explicitly disabled by
IEEE80211_TX_INTFL_DONT_ENCRYPT.
However security_enable was set when *any* key, including
the AP GTK key, had been set which was causing unwanted
encryption even if no key was avaialble for the unicast
packet to be sent.
Fix this by adding a check that we have a key and drop
the old security_enable driver flag which is insufficient
and redundant.
The Redpine downstream out of tree driver does it this way too.
Regarding the Fixes tag the actual code being modified was
introduced earlier, with the original driver submission, in dad0d04fa7ba ("rsi: Add RS9113 wireless driver"), however
at that time AP mode was not yet supported so there was
no bug at that point.
So I have tagged the introduction of AP support instead
which was part of the patch set "rsi: support for AP mode" [1]
It is not clear whether AP WPA has ever worked, I can see nothing
on the kernel side that broke it afterwards yet the AP support
patch series says "Tests are performed to confirm aggregation,
connections in WEP and WPA/WPA2 security."
One possibility is that the initial tests were done with a modified
userspace (hostapd).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Fixes: 38ef62353acb ("rsi: security enhancements for AP mode") CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1622564459-24430-1-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RSI_RATE_x bits must be assigned to struct rsi_data_desc rate_info
field. The rest of the driver does it correctly, except this one place,
so fix it. This is also aligned with the RSI downstream vendor driver.
Without this patch, an AP operating at 5 GHz does not transmit any
beacons at all, this patch fixes that.
Fixes: d26a9559403c ("rsi: add beacon changes for AP mode") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com> Cc: Angus Ainslie <angus@akkea.ca> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Karun Eagalapati <karun256@gmail.com> Cc: Martin Kepplinger <martink@posteo.de> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Cc: Siva Rebbagondla <siva8118@gmail.com> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210507213105.140138-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It doesn't make sense to clobber the const driver-side buffer, if a
write-to-device attempt failed. All other SSB variants (PCI, PCMCIA and SoC)
also don't corrupt the buffer on any failure in block_write.
Therefore, remove this memset from the SDIO variant.
Signed-off-by: Michael Büsch <m@bues.ch> Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210515210252.318be2ba@wiggum Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got this crash more times during debugging of PCIe controller and crash
happens somehow at the time when PCIe kernel code started link retraining (as
part of ASPM code) when at the same time PCIe link went down and ath9k probably
executed hw reset procedure.
Currently I'm not able to reproduce this issue as it looks like to be
some race condition between link training, ASPM, link down and reset
path. And as always, race conditions which depends on more input
parameters are hard to reproduce as it depends on precise timings.
But it is clear that pointers are zero in this case and should be
properly filled as same code pattern is used in ath9k_stop() function.
Anyway I was able to reproduce this crash by manually triggering ath
reset worker prior putting card up. I created simple patch to export
reset functionality via debugfs and use it to "simulate" of triggering
reset. s proved that NULL-pointer dereference issue is there.
Function ath9k_hw_reset() is dereferencing chan structure pointer, so it
needs to be non-NULL pointer.
Function ath9k_stop() already contains code which sets ah->curchan to valid
non-NULL pointer prior calling ath9k_hw_reset() function.
Add same code pattern also into ath_reset_internal() function to prevent
kernel NULL pointer dereference in ath9k_hw_reset() function.
This change fixes kernel NULL pointer dereference in ath9k_hw_reset() which
is caused by calling ath9k_hw_reset() from ath_reset_internal() with NULL
chan structure.
projects / thirdparty / kernel / stable.git / log
