Stefan Koch [Fri, 24 Mar 2017 16:08:59 +0000 (17:08 +0100)]
lantiq: cleanup code ar9-vr9 parts
- remove unused code within 500-ar9_vr9.patch
- fixed return of IFX_ERROR (solves SIGSEGV in asterisk at failure)
- align it a bit with 400-falcon.patch
- remove 600-kernel-4.9.patch since changed parts
are removed during cleanup
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Hauke Mehrtens [Sun, 26 Mar 2017 17:20:33 +0000 (19:20 +0200)]
kernel: add arm64 erratums into config
Deactivate all the ARM64 erratums by default. The target code should
activate them if needed. This fixes a problem with a new erratum added
in kernel 4.9.17 breaking brcm2708.
Rafał Miłecki [Wed, 22 Mar 2017 22:35:39 +0000 (23:35 +0100)]
brcm2708: backport upstream ARM dts commits
This gets us in sync with dts from kernel 4.11. Two patches were already
backported earlier.
I decided to use 03x prefix as it's kind of similar to the 3xx prefix:
3xx - architecture specific patches
It isn't any documented or strict rule though. We don't need to stick to
it if we hit any problems.
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.
Mathias Kresin [Fri, 17 Mar 2017 18:54:55 +0000 (19:54 +0100)]
ath10k-firmware: do not select the qca988x by default
Do not select the qca988x by default as soon as kmod-ath10k is
selected. We do support more ath10k chips than the qca988x in the
meantime, so this dependency doesn't make sense any longer.
Mathias Kresin [Fri, 10 Mar 2017 21:46:30 +0000 (22:46 +0100)]
lantiq: fix pci with kernel 4.9
Commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists") changed
the controller list from reverse to straight order. Use the last entry
in the controller list to get the fist conroller of the system.
Mathias Kresin [Fri, 17 Mar 2017 06:29:16 +0000 (07:29 +0100)]
kernel: add MIPS pci fix send upstream
Upstream commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists")
changed the controller list from reverse to straight order without
taking care of the changed order for the scan of the recorded PCI
controllers.
Traverse the list in reverse order to restore the former behaviour.
This patches fixes the following PCI error on lantiq:
pci 0000:01:00.0: BAR 0: error updating (0x1c000004 != 0x000000)
Rafał Miłecki [Wed, 22 Mar 2017 20:09:00 +0000 (21:09 +0100)]
brcm2708: rename all patches from raspberrypi git tree to use 950 prefix
Right now all brcm2708 patches are extracted from the non-mainline
raspberrypi/linux git tree. Many of them are hacks and/or are unneeded
in LEDE. Raspberry Pi is getting better and better mainline support so
it would be nice to finally start maintaining patches in a cleaner way:
1) Backport patches accepted in upstream tree
2) Start using upstream drivers
3) Pick only these patches that are needed for more complete support
Handling above tasks requires grouping patches - ideally using the same
prefixes as generic ones. It means we should rename existing patches to
use some high prefix. This will allow e.g. use 0xx for backported code.
Piotr Dymacz [Wed, 15 Mar 2017 23:54:08 +0000 (00:54 +0100)]
ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.
CPE505 is an outdoor CPE with PoE support and detachable antennas.
Both devices are based on Qualcomm/Atheros QCA9531 v2.
Common specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB
R602N specification:
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button
CPE505N specification:
- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button
Flash instructions:
It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").
Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:
Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.
If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:
These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".
Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.
Hans Dedecker [Wed, 22 Mar 2017 20:56:05 +0000 (21:56 +0100)]
odhcp6c: update to git HEAD version
0463b05 dhcpv6: rebind capability support in reconfigure message (rfc6644) 53767fc dhcpv6: respect renew end point when handling reconfigure message dd892e2 dhcpv6: calculate T1, T2 and T3 in a more sane manner 8a6ca6e md5: use libubox md5 library as local implementation 89822de dhcpv6: don't return renew msg in case of invalid msg type in reconfigure msg 4160c0e treewide: align coding style
Felix Fietkau [Wed, 22 Mar 2017 19:46:14 +0000 (20:46 +0100)]
ath9k: fix power limits on init
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lowr limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Felix Fietkau [Wed, 22 Mar 2017 19:24:32 +0000 (20:24 +0100)]
ath: do not apply broken power limits with ATH_USER_REGD
If a device uses the default EEPROM code, typically only the main CTLs
are valid, and they do not apply properly when switching to a different
regulatory domain. If the regdomain deviates from the EEPROM one, force
the world roaming regdomain to ensure that power limits are sane
Daniel Engberg [Mon, 20 Mar 2017 08:51:26 +0000 (09:51 +0100)]
utils/util-linux: Update to 2.29.2
Update util-linux to 2.29.2
Remote 0001-fix-uClibc-ng-scanf-check.patch as it's been merged upstream.
Refresh patches
Change ncurses to ncursesw to fix compilation and avoid confusion
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove faulty dependency changes]
Ian Pozella [Thu, 2 Feb 2017 09:42:04 +0000 (09:42 +0000)]
target: add pistachio
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com> Signed-off-by: Francois Berder <francois.berder@imgtec.com> Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com> Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com> Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
Ian Pozella [Wed, 15 Feb 2017 09:05:24 +0000 (09:05 +0000)]
pistachio: add 4.9 kernel support
This adds kernel support for the Pistachio SoC and the Marduk (Ci40)
board which uses it.
Much of the code for Pistachio has been upstreamed however some
patches are still required to boot from the Marduk board:
* spi bug fixes
* dma bug fixes
* pistachio internal clock tree bug fixes
* spi-nand implementation
* dts based mtd device naming scheme
* dts backports and bug fixes
mac80211: Fix race condition leading to wifi interfaces not coming up at boot sometimes.
In the drv_mac80211_setup function, mac80211_interface_cleanup
is called to ask the kernel to delete all existing interfaces
for the phy that is being configured via netlink.
Later in the first function, mac80211_prepare_vif is called to
set up the new interfaces as required.
But sometimes, when mac80211_prepare_vif (and so the relevant
`iw phy x interface add y` command) runs, the kernel might still
be cleaning up the old interface with the same ifname. It usually
takes very few time to do that; possibly a few milliseconds of
sleep in the script after detecting this error condition could be
enough, but the busybox sh does not support sub-second sleep
intervals.
When this happens, iw obviously fails to create the new interface;
and the following message is printed in the system log, followed by
subsequent failure messages from hostapd in case this would have been
an AP interface.
Tue Mar 14 04:21:57 2017 daemon.notice netifd: radio1 (2767): command failed: Too many open files in system (-23)
This was a long-standing issue existing since at least OpenWrt Backfire,
and today I finally managed to debug and (hopefully) solve it.
It was happening very few times on most devices; but it was happening
a lot more frequently on fast platforms with multiple radios, such as
the powerpc-based dual-ath9k-radio tl-wdr4900-v1.
"board-2 is a key-value store of actual board files.
Some devices, notably qca61x4 hw3+ and qca4019 need
distinct board files to be uploaded. Otherwise they
fail in various ways." [0].
Later on Rajkumar Manoharan explained:
"In QCA4019 platform, only radio specific calibration
(pre-cal-data) is stored in flash. Board specific contents
are read from board-2.bin. For each radio appropriate board
data should be loaded. To fetch correct board data from
board-2.bin bundle, pre-cal/radio specific caldata should
be loaded first to get proper board id.
|My understanding until now was that:
|
| * pre-cal data + board-2.bin info == actual calibration data
Correct." [1].
The standard board-2.bin from the ath10k-firmware-qca4019
barely works on the RT-AC58U. Especially 5GHz clients fail
to connect at all and if they do, they have very low
throughput even right next to the router.
Currently, the solution for this problem is to supply a
custom board-2.bin for every device.
To implement this feature, this method makes use of:
Rafał Miłecki's "base-files: add support for overlaying
rootfs content". This comes with a few limitations:
1. Since there can only be one board-2.bin at the right
location, there can only one board overwrite installed
at any time. (All packages CONFLICT with each other.
It's also not possible to "builtin" multiple package.)
2. updating ath10k-firmware-qca4019 will also replace
the board-2.bin. For this cases the user needs to
manually reinstall the wifi-board package once the
ath10k-firmware-qca4019 is updated.
To create the individual board-2.bin: Use the ath10k-bdencoder
utility from the qca-swiss-army-knife repository:
<https://github.com/qca/qca-swiss-army-knife>
The raw board.bin files have to be extracted from the
vendor's source GPL.tar archieves.
Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
This patch enables the ATH10K_AHB support for the QCA4019
devices on the AHB bus.
This patch also removes 936-ath10k_skip_otp_check.patch
because it breaks the AHB device identification.
"Patch is wrong. I find it frustrating OpenWRT/LEDE doesn't
try to work with upstream on ixing these things right."
Martin Schiller [Thu, 16 Mar 2017 10:25:53 +0000 (11:25 +0100)]
openvpn: add extra respawn parameters
This change protects the openvpn instances to be marked as "in a crash
loop" and thereby the connection retries will run infinitely.
When the remote site of an openvpn connection goes down for some time
(network failure etc.) the openvpn instance in an openwrt/lede device
should not stop retrying to establish the connection.
With the current limit of 5 retries, there is a user interaction
required, which isn't really what you want when the device should
simply do everything to keep the vpn connection up.
Daniel Engberg [Mon, 20 Mar 2017 08:51:26 +0000 (09:51 +0100)]
utils/util-linux: Update to 2.29.2
Update util-linux to 2.29.2
Remote 0001-fix-uClibc-ng-scanf-check.patch as it's been merged upstream.
Refresh patches
Change ncurses to ncursesw to fix compilation and avoid confusion
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Rafał Miłecki [Tue, 21 Mar 2017 21:57:56 +0000 (22:57 +0100)]
umdns: update to the version 2017-03-21
This includes following changes: 480d7bc Fix sending unicast questions on cache expire a0403cd Keep source sockaddr for every cached DNS record 1478293 Fix code freeing cached non-A(AAA) records too early 9f1cc22 Fix replying to "QU" questions received on unicast interface 943bedb Fix reading port of incoming packets c725494 Use MCAST_PORT define for port 5353 ce7e9e9 Use one define for DNS-Based Service Discovery service name e1bacef Drop entries cached for interface we're going to delete 496aeba Fix comment typo in cache_gc_timer f89986b Fix refreshing cached A(AAA) records that expire
Previous updates made umdns work as expected on startup but there were
still many bugs. They were mostly related to runtime - cache management
and requests + responses. E.g. umdns was never able to send question on
DNS record expire. It was also ignoring all incoming unicast questions.
Since these issues are quite serious it makes sense to backport this
update to the stable branch.
Hans Dedecker [Tue, 21 Mar 2017 21:54:47 +0000 (22:54 +0100)]
netifd: update to git HEAD version
a032166 interface-ip: set prefix indicator flag when IPv6 prefix lifetime changes b4f8984 system-linux: parse vti specific settings as nested json data object 7e3b89a system-linux: parse gre specific settings as nested json data object
Hauke Mehrtens [Tue, 14 Mar 2017 17:55:02 +0000 (18:55 +0100)]
scripts: only generate config from feature flag if fully match
Without this change the code checked if the string was contained in the
feature option and not if the string matches the complete word. This only
removes the nand option from the omap24xx target, the other changes are
only removing options which were added twice.
projects / thirdparty / openwrt.git / log
