rss_ctx.test_rss_key_indir implicitly expects at least 5 queues,
as it checks that the traffic on first 2 queues is lower than
the remaining queues when we use all queues. Special case fewer
queues.
We want to mount beneath the given location. For that operation to
make sense, location must be the root of some mount that has something
under it. Currently we let it proceed if those requirements are not met,
with rather meaningless results, and have that bogosity caught further
down the road; let's fail early instead - do_lock_mount() doesn't make
sense unless those conditions hold, and checking them there makes
things simpler.
Reviewed-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SMC can take an excessive amount of time to process some
messages under some conditions.
Background:
Sending a message to the SMC works by writing the message into
the mmSMC_MESSAGE_0 register and its optional parameter into
the mmSMC_SCRATCH0, and then polling mmSMC_RESP_0. Previously
the timeout was AMDGPU_MAX_USEC_TIMEOUT, ie. 100 ms.
Increase the timeout to 200 ms for all messages and to 1 sec for
a few messages which I've observed to be especially slow:
PPSMC_MSG_NoForcedLevel
PPSMC_MSG_SetEnabledLevels
PPSMC_MSG_SetForcedLevels
PPSMC_MSG_DisableULV
PPSMC_MSG_SwitchToSwState
This fixes the following problems on Tahiti when switching
from a lower clock power state to a higher clock state, such
as when DC turns on a display which was previously turned off.
* si_restrict_performance_levels_before_switch would fail
(if the user previously forced high clocks using sysfs)
* si_set_sw_state would fail (always)
It turns out that both of those failures were SMC timeouts and
that the SMC actually didn't fail or hang, just needs more time
to process those.
Add a warning when there is an SMC timeout to make it easier to
identify this type of problem in the future.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kfd CRIU checkpoint ioctl would return an error if trying
to checkpoint a process with no kfd buffer objects.
This is a normal case and should not be an error.
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: David Francis <David.Francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver unconditionally saves current state on first init in
dsi_pll_7nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_7nm_pll_restore_state().
Restoring calls dsi_pll_7nm_vco_set_rate() with
pll_7nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
According to Hardware Programming Guide for DSI PHY, the retime buffer
resync should be done after PLL clock users (byte_clk and intf_byte_clk)
are enabled. Downstream also does it as part of configuring the PLL.
Driver was only turning off the resync FIFO buffer, but never bringing it
on again.
DMA Engine has support for the callback_result which provides
the status of the request and the residue. This helps in
determining the correct status of the request and in
efficient resource management of the request.
The 'callback_result' method is preferred over the deprecated
'callback' method.
This patch modifies the type of setup_xref from void to int and handles
errors since the function can fail.
`setup_xref` now returns the (eventual) error from
`dmae_set_dmars`|`dmae_set_chcr`, while `shdma_tx_submit` handles the
result, removing the chunks from the queue and marking PM as idle in
case of an error.
When a buffer object (BO) is allocated with the XE_BO_FLAG_GGTT_INVALIDATE
flag, the driver initiates TLB invalidation requests via the CTB mechanism
while releasing the BO. However a premature release of the CTB BO can lead
to system crashes, as observed in:
Introduce a devm-managed release action during xe_guc_ct_init() and
xe_guc_ct_init_post_hwconfig() to ensure proper CTB disablement before
resource deallocation, preventing the use-after-free scenario.
Signed-off-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Summers Stuart <stuart.summers@intel.com> Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Link: https://lore.kernel.org/r/20250901072541.31461-1-satyanarayana.k.v.p@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Networking drivers implementing PTP clocks and kernel socket code
handling hardware timestamps use the 64-bit signed ktime_t type counting
nanoseconds. When a PTP clock reaches the maximum value in year 2262,
the timestamps returned to applications will overflow into year 1667.
The same thing happens when injecting a large offset with
clock_adjtime(ADJ_SETOFFSET).
The commit 7a8e61f84786 ("timekeeping: Force upper bound for setting
CLOCK_REALTIME") limited the maximum accepted value setting the system
clock to 30 years before the maximum representable value (i.e. year
2232) to avoid the overflow, assuming the system will not run for more
than 30 years.
Enforce the same limit for PTP clocks. Don't allow negative values and
values closer than 30 years to the maximum value. Drivers may implement
an even lower limit if the hardware registers cannot represent the whole
interval between years 1970 and 2262 in the required resolution.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <jstultz@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250828103300.1387025-1-mlichvar@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
trans_pcie::fh_mask and hw_mask indicates what are the interrupts are
currently enabled (unmasked).
When we disable all interrupts, those should be set to 0, so if, for
some reason, we get an interrupt even though it was disabled, we will
know to ignore.
The current implementation unconditionally calls
mxc_isi_video_cleanup_streaming() in mxc_isi_video_release(). This can
lead to situations where any release call (like from a simple
"v4l2-ctl -l") may release a currently streaming queue when called on
such a device.
This is reproducible on an i.MX8MP board by streaming from an ISI
capture device using gstreamer:
Address this issue by moving the streaming preparation and cleanup to
the vb2 .prepare_streaming() and .unprepare_streaming() operations. This
also simplifies the driver by allowing direct usage of the
vb2_ioctl_streamon() and vb2_ioctl_streamoff() helpers, and removal of
the manual cleanup from mxc_isi_video_release().
Link: https://lore.kernel.org/r/20250813212451.22140-2-laurent.pinchart@ideasonboard.com Signed-off-by: Richard Leitner <richard.leitner@linux.dev> Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Richard Leitner <richard.leitner@linux.dev> # i.MX8MP Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The imx-mipi-csis driver sets the rate of the wrap clock to the value
specified in the device tree's "clock-frequency" property, and defaults
to 166 MHz otherwise. This is a historical mistake, as clock rate
selection should have been left to the assigned-clock-rates property.
Honouring the clock-frequency property can't be removed without breaking
backwards compatibility, and the corresponding code isn't very
intrusive. The 166 MHz default, on the other hand, prevents
configuration of the clock rate through assigned-clock-rates, as the
driver immediately overwrites the rate. This behaviour is confusing and
has cost debugging time.
There is little value in a 166 MHz default. All mainline device tree
sources that enable the CSIS specify a clock-frequency explicitly, and
the default wrap clock configuration on supported platforms is at least
as high as 166 MHz. Drop the default, and only set the clock rate
manually when the clock-frequency property is specified.
On FSD platform, gating the reference clock (ref_clk) and putting the
UFS device in reset by asserting the reset signal during UFS suspend,
improves the power savings and ensures the PHY is fully turned off.
These operations are added as FSD specific suspend hook to avoid
unintended side effects on other SoCs supported by this driver.
Co-developed-by: Nimesh Sati <nimesh.sati@samsung.com> Signed-off-by: Nimesh Sati <nimesh.sati@samsung.com> Signed-off-by: Bharat Uppal <bharat.uppal@samsung.com> Link: https://lore.kernel.org/r/20250821053923.69411-1-bharat.uppal@samsung.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make the "mclk" clock optional in the ad7124 driver. The MCLK is an
internal counter on the ADC, so it is not something that should be
coming from the devicetree. However, existing users may be using this
to essentially select the power mode of the ADC from the devicetree.
In order to not break those users, we have to keep the existing "mclk"
handling, but now it is optional.
Now, when the "mclk" clock is omitted from the devicetree, the driver
will default to the full power mode. Support for an external clock
and dynamic power mode switching can be added later if needed.
As noted in the kernel documentation [1], open-coded multiplication in
allocator arguments is discouraged because it can lead to integer overflow.
Use kcalloc() to gain built-in overflow protection, making memory
allocation safer when calculating allocation size compared to explicit
multiplication. Similarly, use size_add() instead of explicit addition
for 'uobj_chunk_num + sobj_chunk_num'.
Introduce support for standard MII ioctl operations in the LAN865x
Ethernet driver by implementing the .ndo_eth_ioctl callback. This allows
PHY-related ioctl commands to be handled via phy_do_ioctl_running() and
enables support for ethtool and other user-space tools that rely on ioctl
interface to perform PHY register access using commands like SIOCGMIIREG
and SIOCSMIIREG.
This feature enables improved diagnostics and PHY configuration
capabilities from userspace.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: stp@e100bb0 (lantiq,gpio-stp-xway): $nodename:0: 'stp@e100bb0' does not match '^gpio@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bindig requires a node name matching ‘^gpio@[0-9a-f]+$’. This patch
changes the clock name from “stp” to “gpio”.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: pci@e105400 (lantiq,pci-xway): 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/pci/pci-bus-common.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: / (lantiq,xway): 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warnings:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpu@0 (mips,mips24Kc): 'reg' is a required property
from schema $id: http://devicetree.org/schemas/mips/cpus.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Update the legacy (non-DC) display code to respect the maximum
pixel clock for HDMI and DVI-D. Reject modes that would require
a higher pixel clock than can be supported.
Also update the maximum supported HDMI clock value depending on
the ASIC type.
For reference, see the DC code:
check max_hdmi_pixel_clock in dce*_resource.c
v2:
Fix maximum clocks for DVI-D and DVI/HDMI adapters.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why & How]
Previously, when calculating dto phase, we would incorrectly fail when phase
<=0 without additionally checking for the integer value. This meant that
calculations would incorrectly fail when the desired pixel clock was an exact
multiple of the reference clock.
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Clay King <clayking@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
-Pipe splitting allows for clocks to be reduced, but when using TMDS 420,
reduced clocks lead to missed clocks cycles on clock resyncing
[How]
-Impose a minimum clock when using TMDS 420
Reviewed-by: Chris Park <chris.park@amd.com> Signed-off-by: Relja Vojvodic <rvojvodi@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can have modules in path which can change the number of channels and in
this case the BE params needs to be adjusted to configure the DAI according
to the copier configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Message-ID: <20250829105305.31818-2-peter.ujfalusi@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compare the whole v4l2_bt_timings struct, not just the width/height when
setting new timings. Timings with the same resolution and different
pixelclock can now be properly set.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 0d6ccfe6b319 ("selftests: drv-net: rss_ctx: check for all-zero keys")
added a skip exception if NIC has fewer than 3 queues enabled,
but it's just constructing the object, it's not actually rising
this exception.
Before:
# Exception| net.lib.py.utils.CmdExitFailure: Command failed: ethtool -X enp1s0 equal 3 hkey d1:cc:77:47:9d:ea:15:f2:b9:6c:ef:68:62:c0:45:d5:b0:99:7d:cf:29:53:40:06:3d:8e:b9:bc:d4:70:89:b8:8d:59:04:ea:a9:c2:21:b3:55:b8:ab:6b:d9:48:b4:bd:4c:ff:a5:f0:a8:c2
not ok 1 rss_ctx.test_rss_key_indir
After:
ok 1 rss_ctx.test_rss_key_indir # SKIP Device has fewer than 3 queues (or doesn't support queue stats)
Filter out modes that have a clock rate greater than the max core clock
rate when adjusted for the perf clock factor
This is especially important for chipsets such as QCS615 that have lower
limits for the MDP max core clock.
Since the core CRTC clock is at least the mode clock (adjusted for the
perf clock factor) [1], the modes supported by the driver should be less
than the max core clock rate.
A partitioned system configured with only one package and one compute
die, warning will be generated for duplicate sysfs entry. This typically
occurs during the platform bring-up phase.
Partitioned systems expose dies, equivalent to TPMI compute domains,
through the CPUID. Each partitioned system must contains at least one
compute die per partition, resulting in a minimum of two dies per
package. Hence the function topology_max_dies_per_package() returns at
least two, and the condition "topology_max_dies_per_package() > 1"
prevents the creation of a root domain.
In this case topology_max_dies_per_package() will return 1 and root
domain will be created for partition 0 and a duplicate sysfs warning
for partition 1 as both partitions have same package ID.
To address this also check for non zero partition in addition to
topology_max_dies_per_package() > 1.
When beacon loss happens or the RSSI drops, trigger MLO scan only
if not in EMLSR. The link switch was meant to be done when we are
not in EMLSR and we can try to switch to a better link.
If in EMLSR, we exit first and then trigger MLO scan.
Upon experiencing a PCI error, fbnic reset the device to recover from
the failure. Reset the hardware stats as part of the device reset to
ensure accurate stats reporting.
Note that the reset is not really resetting the aggregate value to 0,
which may result in a spike for a system collecting deltas in stats.
Rather, the reset re-latches the current value as previous, in case HW
got reset.
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250825200206.2357713-3-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes an issue where two different flows on the same RXq
produce the same hash resulting in continuous flow overwrites.
Flow #1: A packet for Flow #1 comes in, kernel calls the steering
function. The driver gives back a filter id. The kernel saves
this filter id in the selected slot. Later, the driver's
service task checks if any filters have expired and then
installs the rule for Flow #1.
Flow #2: A packet for Flow #2 comes in. It goes through the same steps.
But this time, the chosen slot is being used by Flow #1. The
driver gives a new filter id and the kernel saves it in the
same slot. When the driver's service task runs, it runs through
all the flows, checks if Flow #1 should be expired, the kernel
returns True as the slot has a different filter id, and then
the driver installs the rule for Flow #2.
Flow #1: Another packet for Flow #1 comes in. The same thing repeats.
The slot is overwritten with a new filter id for Flow #1.
This causes a repeated cycle of flow programming for missed packets,
wasting CPU cycles while not improving performance. This problem happens
at higher rates when the RPS table is small, but tests show it still
happens even with 12,000 connections and an RPS size of 16K per queue
(global table size = 144x16K = 64K).
This patch prevents overwriting an rps_dev_flow entry if it is active.
The intention is that it is better to do aRFS for the first flow instead
of hurting all flows on the same hash. Without this, two (or more) flows
on one RX queue with the same hash can keep overwriting each other. This
causes the driver to reprogram the flow repeatedly.
Changes:
1. Add a new 'hash' field to struct rps_dev_flow.
2. Add rps_flow_is_active(): a helper function to check if a flow is
active or not, extracted from rps_may_expire_flow(). It is further
simplified as per reviewer feedback.
3. In set_rps_cpu():
- Avoid overwriting by programming a new filter if:
- The slot is not in use, or
- The slot is in use but the flow is not active, or
- The slot has an active flow with the same hash, but target CPU
differs.
- Save the hash in the rps_dev_flow entry.
4. rps_may_expire_flow(): Use earlier extracted rps_flow_is_active().
Testing & results:
- Driver: ice (E810 NIC), Kernel: net-next
- #CPUs = #RXq = 144 (1:1)
- Number of flows: 12K
- Eight RPS settings from 256 to 32768. Though RPS=256 is not ideal,
it is still sufficient to cover 12K flows (256*144 rx-queues = 64K
global table slots)
- Global Table Size = 144 * RPS (effectively equal to 256 * RPS)
- Each RPS test duration = 8 mins (org code) + 8 mins (new code).
- Metrics captured on client
Legend for following tables:
Steer-C: #times ndo_rx_flow_steer() was Called by set_rps_cpu()
Steer-L: #times ice_arfs_flow_steer() Looped over aRFS entries
Add: #times driver actually programmed aRFS (ice_arfs_build_entry())
Del: #times driver deleted the flow (ice_arfs_del_flow_rules())
Units: K = 1,000 times, M = 1 million times
Some observations:
1. Overall Latency improved: (1790.19-1634.94)/1790.19*100 = 8.67%
2. Overall CPU increased: (777.32-751.49)/751.45*100 = 3.44%
3. Flow Management (add/delete) remained almost constant at ~11K
compared to values in millions.
Add a new _fini() routine on the GT TLB invalidation
side to handle this worker cleanup on driver teardown.
v2: Move the TLB teardown to the gt fini() routine called during
gt_init rather than in gt_alloc. This way the GT structure stays
alive for while we reset the TLB state.
[WHY&HOW]
The sink max slice width limitation should be considered for DSC, but
was removed in "refactor DSC cap calculations".
This patch adds it back and takes the valid minimum between the sink and
source.
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When KFD asks CP to preempt queues, other than preempt CP queues, CP
also requests SDMA to preempt SDMA queues with UNMAP_LATENCY timeout.
Currently queue_preemption_timeout_ms is 9000 ms by default but can be
configured via module parameter. KFD_UNMAP_LATENCY_MS is hard coded as
4000 ms though. This patch ties KFD_UNMAP_LATENCY_MS to
queue_preemption_timeout_ms so in a slow system such as emulator, both
CP and SDMA slowness are taken into account.
Signed-off-by: Amber Lin <Amber.Lin@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
For the HW cursor, its current position in the pipe_ctx->stream struct is
not affected by the 180 rotation, i. e. the top left corner is still at
0,0. However, the DPP & HUBP set_cursor_position functions require rotated
position.
The current approach is hard-coded for ODM 2:1, thus it's failing for
ODM 4:1, resulting in a double cursor.
[How]
Instead of calculating the new cursor position relatively to the
viewports, we calculate it using a viewavable clip_rect of each plane.
The clip_rects are first offset and scaled to the same space as the
src_rect, i. e. Stream space -> Plane space.
In case of a pipe split, which divides the plane into 2 or more viewports,
the clip_rect is the union of all the viewports of the given plane.
With the assumption that the viewports in HUBP's set_cursor_position are
in the Plane space as well, it should produce a correct cursor position
for any number of pipe splits.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Signed-off-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When it only allocates vram without va, which is 0, and a
SVM range allocated stays in this range, the vram allocation
returns failure. It should be skipped for this case from
SVM usage check.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Ce Sun <cesun102@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
By polling, poll ACA bank count to ensure that valid
ACA bank reg info can be obtained
v2: add corresponding delay before send msg to SMU to query mca bank info
(Stanley)
v3: the loop cannot exit. (Thomas)
v4: remove amdgpu_aca_clear_bank_count. (Kevin)
v5: continuously inject ce. If a creation interruption
occurs at this time, bank reg info will be lost. (Thomas)
v5: each cycle is delayed by 100ms. (Tao)
Signed-off-by: Ce Sun <cesun102@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pci_endpoint_test tests the 32-bit MSI range. However, the device might
not have all vectors configured. For example, if msi_interrupts is 8 in the
ep function space or if the MSI Multiple Message Capable value is
configured as 4 (maximum 16 vectors).
In this case, do not attempt to run the test to avoid timeouts and directly
return the error value.
This patch ensures the gt will be awake for the entire duration
of the resume sequences until GuCRC takes over and GT-C6 gets
re-enabled.
Before suspending GT-C6 is kept enabled, but upon resume, GuCRC
is not yet alive to properly control the exits and some cases of
instability and corruption related to GT-C6 can be observed.
The original commit be2ff42c5d6e ("fuse: Use hash table to link
processing request") converted fuse_pqueue->processing to a hash table,
but virtio_fs_enqueue_req() was not updated to use it correctly.
So use fuse_pqueue->processing as a hash table, this make the code
more coherent
Co-developed-by: Fushuai Wang <wangfushuai@baidu.com> Signed-off-by: Fushuai Wang <wangfushuai@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The test currently modifies the HDS settings and doesn't restore them.
This may cause subsequent tests to fail (or pass when they should not).
Add defer()ed reset handling.
fixed_phy_register() creates and registers the phy_device. To be
symmetric, we should not only unregister, but also free the phy_device
in fixed_phy_unregister(). This allows to simplify code in users.
Note wrt of_phy_deregister_fixed_link():
put_device(&phydev->mdio.dev) and phy_device_free(phydev) are identical.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/ad8dda9a-10ed-4060-916b-3f13bdbb899d@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 9ab440a9d042 ("drm/xe/ptl: L3bank mask is not
available on the media GT") added a workaround to ignore
the fuse register that L3 bank availability as it did not
contain valid values. Same is true for WCL therefore extend
the workaround to cover it.
Device can be unbound, so driver must also release memory for the wakeup
source. Do not use devm interface, because it would change the order of
cleanup.
Eliminate the use of static variables within the log pull implementation
to resolve a race condition and prevent data gaps when pulling logs from
multiple controllers in parallel, ensuring each operation is properly
isolated.
Firmware can enter a transient fault while creating operational queues.
The driver fails the load immediately.
Add a retry loop that checks controller status and history bit after
queue creation. If either indicates a fault, retry init up to a set
limit before failing.
When Wi-Fi is scanning at 2.4GHz, PTA will abort almost all the BT request.
Once the Wi-Fi slot stay too long, BT audio device can not get enough data,
audio glitch will happened. This patch limit 2.4Ghz Wi-Fi slot to 80ms
while Wi-Fi is scanning to avoid audio glitch.
During enclosure reboot or expander reset, firmware may report a link
speed of 0 in "Device Add" events while the link is still coming up.
The driver drops such devices, leaving them missing even after the link
recovers.
Fix this by treating link speed 0 as 1.5 Gbps during device addition so
the device is exposed to the OS. The actual link speed will be updated
later when link-up events arrive.
Currently, ip_extract_route_hint uses RTN_BROADCAST to decide
whether to use the route dst hint mechanism.
This check is too strict, as it prevents directed broadcast
routes from using the hint, resulting in poor performance
during bursts of directed broadcast traffic.
Fix this in ip_extract_route_hint and modify ip_route_use_hint
to preserve the intended behaviour.
Module aliases are used by userspace to identify the correct module to
load for a detected hardware. The currently supported RPMSG device IDs for
this module include "rpmsg-raw", but the module alias is "rpmsg_chrdev".
Use the helper macro MODULE_DEVICE_TABLE(rpmsg) to export the correct
supported IDs. And while here, to keep backwards compatibility we also add
the other ID "rpmsg_chrdev" so that it is also still exported as an alias.
This has the side benefit of adding support for some legacy firmware
which still uses the original "rpmsg_chrdev" ID. This was the ID used for
this driver before it was upstreamed (as reflected by the module alias).
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Hari Nagalla <hnagalla@ti.com> Tested-by: Hari Nagalla <hnagalla@ti.com> Link: https://lore.kernel.org/r/20250619205722.133827-1-afd@ti.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GPD devices originally used BMI160 sensors with the "BMI0160" PNP ID.
When they switched to BMI260 sensors in newer hardware, they reused
the existing Windows driver which accepts both "BMI0160" and "BMI0260"
IDs. Consequently, they kept "BMI0160" in DSDT tables for new BMI260
devices, causing driver mismatches in Linux.
1. GPD updated BIOS v0.40+[1] for newer devices to report "BMI0260" for
BMI260 sensors to avoid loading the bmi160 driver on Linux. While this
isn't Bosch's VID;
2. Bosch's official Windows driver uses "BMI0260" as a compatible ID
3. We're seeing real devices shipping with "BMI0260" in DSDT
The DSDT excerpt of GPD G1619-04 with BIOS v0.40:
Scope (_SB.I2CC)
{
Device (BMA2)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "BMI0260") // _HID: Hardware ID
Name (_CID, "BMI0260") // _CID: Compatible ID
Name (_DDN, "Accelerometer") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x0069, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2CC",
0x00, ResourceConsumer, , Exclusive,
)
})
Return (RBUF) /* \_SB_.I2CC.BMA2._CRS.RBUF */
}
# omit some noise
}
}
At least for panel-bridges, the atomic_enable call is defined as being
called right after the preceding element in the display pipe is enabled.
It is also stated that "The bridge can assume that the display pipe (i.e.
clocks and timing signals) feeding it is running when this callback is
called"
This means the DSI controller driving this display would have already
switched over to video-mode from command mode and thus dcs functions
should not be called anymore at this point.
This caused a non-working display for me, when trying to enable
the rk3576 dsi controller using a display using this controller.
Therefore move the display_on/off calls the more appropriate
prepare/unprepare callbacks.
The prepare function turns on the power-supply regulator first, when
preparing the display. But in an error case, just returns the error
code, but does not power off the regulator again, fix that.
There are two registers filled in when reading data from
pcode besides the mailbox itself. Currently, we allow a NULL
value for the second of these two (data1) and assume the first
is defined. However, many of the routines that are calling
this function assume that pcode will ignore the value being
passed in and so leave that first value (data0) defined but
uninitialized. To be safe, make sure this value is always
initialized to something (0 generally) in the event pcode
behavior changes and starts using this value.
Due to a hardware errata, CN10k and earlier Octeon silicon series,
the hardware may incorrectly assert XOFF on certain channels during
reset. As a workaround, a write operation to the NIX_AF_RX_CHANX_CFG
register can be performed to broadcast XON signals on the affected
channels
Just add fixed struct size validations for UAC2 and UAC3 effect
units. The descriptor has a variable-length array, so it should be
validated with a proper function later once when the unit is really
parsed and used by the driver (currently only referred partially for
the input terminal parsing).
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Make the following two changes:
(1) Replace -ENOMEM with -ENOSPC in max3100_probe().
(2) Just return -ENOMEM instead in max310x_probe().
The error handling path in pci_p2pdma_add_resource() contains a bug in its
`pgmap_free` label.
Memory is allocated for the `p2p_pgmap` struct, and the pointer is stored
in `p2p_pgmap`. However, the error path calls devm_kfree() with `pgmap`,
which is a pointer to a member field within the `p2p_pgmap` struct, not the
base pointer of the allocation.
Correct the bug by passing the correct base pointer, `p2p_pgmap`, to
devm_kfree().
As reported, on-disk footer.ino and footer.nid is the same and
out-of-range, let's add sanity check on f2fs_alloc_nid() to detect
any potential corruption in free_nid_list.
Initially, trace_sock_exceed_buf_limit() was invoked when
__sk_mem_raise_allocated() failed due to the memcg limit or the
global limit.
However, commit d6f19938eb031 ("net: expose sk wmem in
sock_exceed_buf_limit tracepoint") somehow suppressed the event
only when memcg failed to charge for SK_MEM_RECV, although the
memcg failure for SK_MEM_SEND still triggers the event.
The stmmac_rx function would previously set skb->ip_summed to
CHECKSUM_UNNECESSARY if hardware checksum offload (CoE) was enabled
and the packet was of a known IP ethertype.
However, this logic failed to check if the hardware had actually
reported a checksum error. The hardware status, indicating a header or
payload checksum failure, was being ignored at this stage. This could
cause corrupt packets to be passed up the network stack as valid.
This patch corrects the logic by checking the `csum_none` status flag,
which is set when the hardware reports a checksum error. If this flag
is set, skb->ip_summed is now correctly set to CHECKSUM_NONE,
ensuring the kernel's network stack will perform its own validation and
properly handle the corrupt packet.
When removing a nexthop, commit 90f33bffa382 ("nexthops: don't modify published nexthop groups") added a
call to synchronize_rcu() (later changed to _net()) to make sure
everyone sees the new nexthop-group before the rtnl-lock is released.
When one wants to delete a large number of groups and nexthops, it is
fastest to first flush the groups (ip nexthop flush groups) and then
flush the nexthops themselves (ip -6 nexthop flush). As that way the
groups don't need to be rebalanced.
However, `ip -6 nexthop flush` will still take a long time if there is
a very large number of nexthops because of the call to
synchronize_net(). Now, if there are no more groups, there is no point
in calling synchronize_net(). So, let's skip that entirely by checking
if nh->grp_list is empty.
This gives us a nice speedup:
BEFORE:
=======
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 2097152 nexthops
real 1m45.345s
user 0m0.001s
sys 0m0.005s
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 4194304 nexthops
real 3m10.430s
user 0m0.002s
sys 0m0.004s
AFTER:
======
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 2097152 nexthops
real 0m17.545s
user 0m0.003s
sys 0m0.003s
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 4194304 nexthops
real 0m35.823s
user 0m0.002s
sys 0m0.004s
Signed-off-by: Christoph Paasch <cpaasch@openai.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250816-nexthop_dump-v2-2-491da3462118@openai.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
misc_open() may request module for miscdevice with dynamic minor, which
is meaningless since:
- The dynamic minor allocated is unknown in advance without registering
miscdevice firstly.
- Macro MODULE_ALIAS_MISCDEV() is not applicable for dynamic minor.
Fix by only requesting module for miscdevice with fixed minor.
For miscdevice who wants dynamic minor, it may fail to be registered again
without reinitialization after being de-registered, which is illustrated
by kunit test case miscdev_test_dynamic_reentry() newly added.
There is a real case found by cascardo when a part of minor range were
contained by range [0, 255):
1) wmi/dell-smbios registered minor 122, and acpi_thermal_rel registered
minor 123
2) unbind "int3400 thermal" driver from its device, this will de-register
acpi_thermal_rel
3) rmmod then insmod dell_smbios again, now wmi/dell-smbios is using minor
123
4) bind the device to "int3400 thermal" driver again, acpi_thermal_rel
fails to register.
Some drivers may reuse the miscdevice structure after they are deregistered
If the intention is to allocate a dynamic minor, if the minor number is not
reset to MISC_DYNAMIC_MINOR before calling misc_register(), it will try to
register a previously dynamically allocated minor number, which may have
been registered by a different driver.
One such case is the acpi_thermal_rel misc device, registered by the
int3400 thermal driver. If the device is unbound from the driver and later
bound, if there was another dynamic misc device registered in between, it
would fail to register the acpi_thermal_rel misc device. Other drivers
behave similarly.
Actually, this kind of issue is prone to happen if APIs
misc_register()/misc_deregister() are invoked by driver's
probe()/remove() separately.
Instead of fixing all the drivers, just reset the minor member to
MISC_DYNAMIC_MINOR in misc_deregister() in case it was a dynamically
allocated minor number, as error handling of misc_register() does.
Mark dm error as DM_TARGET_PASSES_INTEGRITY so that it can be stacked on
top of PI capable devices. The claim is strictly speaking as lie as dm
error fails all I/O and doesn't pass anything on, but doing the same for
integrity I/O work just fine :)
This helps to make about two dozen xfstests test cases pass on PI capable
devices.
In WoWLAN net-detect mode, the firmware periodically performs scans
and sends scan reports via C2H, which driver does not need. These
unnecessary C2H events cause firmware watchdog timeout, leading
to unexpected wakeups and SER 0x2599 on 8922AE.
On some Qualcomm platforms such as QCS6490-RB3Gen2, the multiple
WSA8830/WSA8835 speaker amplifiers share a common reset (shutdown) GPIO.
To handle such scenario, use the reset controller framework and its
"reset-gpio" driver to handle such case. This allows proper handling
of all WSA883x speaker amplifiers on QCS6490-RB3Gen2 board.
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com> Link: https://patch.msgid.link/20250815172353.2430981-3-mohammad.rafi.shaik@oss.qualcomm.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
