David Bauer [Thu, 24 Oct 2019 13:13:24 +0000 (15:13 +0200)]
ath79: disable delays on AT803X config init
Until upstream commit 6d4cd041f0af("net: phy: at803x: disable delay
only for RGMII mode"), delays were not disabled on driver probe
for the Atheros AR803x PHYs, although the RX delay is enabled on
soft and hard reset.
In addition, the TX delay setting is retained on soft-reset.
This patch disables both delays on config init to align the behavior
with kernel 5.1 and higher. It can be safely dropped with kernel 5.1.
Sven Roederer [Sat, 9 Mar 2019 14:00:15 +0000 (15:00 +0100)]
build: have scripts/feeds honor all toplevel .mk-files of a feed
The luci and freifunk feed having a common Makefile included by the
individual packages. Currently a change to this file will be ignored
when running "scripts/feeds update".
When we are updating for a feed, add a dependency for all .mk files
in the root of it.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space (especially helpful for the tiny devices).
The only script remaining in parent base-files is
/etc/hotplug.d/ieee80211/00-wifi-migration, everything else is
moved/split.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (generic) 49135 B
split (generic) 48533 B (- 0.6 kiB)
split (tiny) 43337 B (- 5.7 kiB)
split (nand) 44423 B (- 4.6 kiB)
Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipq40xx: add label MAC address for Netgear EX6100v2/EX6150v2
This is based on the EX6150v2, which should be identical to
the EX6100v2:
The device bears two MAC addresses ("MAC 1" and "MAC 2") that
correspond to phy0 and phy1.
The ethernet MAC address (gmac0) is the same as phy0.
As this one is accessible via local-mac-address in gmac0, the
latter is used for label-mac-device.
(Although this is a one-port, gmac1 also has a local-mac-address
assigned. This has the same vendor part as the other addresses,
but completely different data for the device part.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes the remaining IMAGE_SIZE issues in ath79 target.
All devices in target have been checked, so together with
previous patches this target should be "clean" afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath79: tidy up and fix IMAGE_SIZE for Ubiquiti devices
This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by:
1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"),
since despite two all subdefinition have different values.
2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k).
3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node
since all have same size (it is defined in parent DTSI ...).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Factory image generated for Netgear WNR1000 v2 has incorrect device
and hardware ID information in header due to missing makefile
variables. This fix adds them to device section.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
André Valentin [Wed, 23 Oct 2019 09:30:30 +0000 (11:30 +0200)]
ath79: add support for ZyXEL NBG6716
Attention: Kernel partition size has been enlarged to 4MB.
To switch, you must update to latest ar71xx-nand snapshort and flash the
sysupgrade-4M-Kernel.bin:
zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f
You will end up with a fresh config if you do not inject config into the image.
The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but
ath79 can only use the first 128MB. Therefore the complete NAND needs to be
overwritten. If not, the old UBI may make problems and lead to reboot loop.
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6716> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6716>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
Paul Fertser [Fri, 25 Oct 2019 10:18:43 +0000 (13:18 +0300)]
ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2
- CMIIT ID: 2019AP2581
- SoC: MediaTek MT7621
- Flash: 16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM: 128MiB DDR3 (ESMT M15T1G1664A)
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
INSTALLATION:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.
With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.
For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).
Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".
When caldata locations are defined with mediatek,mtd-eeprom the
MAC address is automatically read from offset +4. Thus, specifying
that location explicitly is redundant.
This patch removes those redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The SPI-NAND framework from Linux uses common driver code that is then
"tuned" by a tiny struct of chip-specific data that describes
available commands, timing, and layout (data and OOB data). Several
manufacturers and chips have been added since 4.19, several of which
are used in devices already supported by OpenWrt (typically with no or
"legacy" access to their NAND memory). This commit catches up the
supported-chip definitions through Linux 5.2-rc6 and linux/next.
The driver is only compiled for platforms with CONFIG_MTD_SPI_NAND=y.
This presently includes ipq40xx and pistachio, with the addition of
ath79-nand in these commits (and not ath79-generic or ath79-tiny).
Jeff Kletsky [Wed, 23 Oct 2019 16:55:02 +0000 (09:55 -0700)]
ath79: GL-AR750S: Add I2C Support
The GL-AR750S has an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.2 ms period, ~89 kHz
The board has well-labeled (unpopulated) headers for serial and I2C
along the front edge of the board (the edge with the LEDs). Looking
from the top, rear of the unit (behind Ethernet jacks)
Jeff Kletsky [Wed, 23 Oct 2019 16:55:01 +0000 (09:55 -0700)]
ath79: GL-AR300M series: Add I2C Support
The GL-AR300M series have an internal header for I2C.
Provide DTS definitions for the i2c-gpio driver.
The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,
Default clock measured ~11.4 ms period, ~88 kHz
The board has two sets of (unpopulated) headers. While facing the
back of the board (looking into the Ethernet jacks), and looking from
the top, the one on the left edge of the baord with four holes is the
I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards.
| (Patch antenna)
|
|
| O GND
| O SDA / GPIO 17
| O SCL / GPIO 16
| ⊡ 3V3 (square land)
|
| (Ethernet jacks)
https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states
"Note: I2C is not working in some early version of the router."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Gabor Varga [Tue, 22 Oct 2019 19:44:09 +0000 (21:44 +0200)]
ramips: add support for Asus RT-AC65P
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.
On both routers the installation can be done also via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Changelog:
v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release
Andreas Ziegler [Tue, 22 Oct 2019 20:44:29 +0000 (22:44 +0200)]
ar71xx: add model detection for UniFi AC-LR
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones] Signed-off-by: David Bauer <mail@david-bauer.net>
1. Grab the uboot for the Device from the 'u-boot-fritz1200'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ1200.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
Jonas Gorski [Tue, 22 Oct 2019 19:33:22 +0000 (21:33 +0200)]
brcm63xx: fix build with GCC 8.3
Fixes the following build error when building when using GCC 8.3:
In file included from ./include/linux/string.h:19,
from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./arch/mips/include/asm/processor.h:15,
from ./arch/mips/include/asm/thread_info.h:16,
from ./include/linux/thread_info.h:38,
from ./include/asm-generic/preempt.h:5,
from ./arch/mips/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:81,
from ./include/linux/spinlock.h:51,
from ./include/linux/mmzone.h:8,
from ./include/linux/bootmem.h:8,
from arch/mips/bcm63xx/prom.c:10:
arch/mips/bcm63xx/prom.c: In function 'prom_init':
./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds]
__ret = __builtin_memcpy((dst), (src), __len); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy'
memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
^~~~~~
In file included from arch/mips/bcm63xx/prom.c:14:
./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here
extern char bmips_smp_movevec;
Reported-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
ramips: fix LAN/WAN MAC addresses of Xiaomi MiWiFi Mini board
Based on stock firmware tests, both LAN and WAN ports use the
MAC address from 0x28 on factory partition.
In OpenWrt, this one is already set in DTS. This patch removes the
local bit set in 02_network previously, and adjusts LAN/WAN
addresses as on stock firmware.
Note that in tests we found a MAC address in 0x2e that is the one
in 0x28 plus 1. Since stock firmware does not use it though, we
do not use it either.
Thanks to Chih-Wei Chen for testing this on his device.
ref: https://github.com/openwrt/openwrt/pull/2497
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roman Yeryomin [Mon, 21 Oct 2019 21:10:20 +0000 (00:10 +0300)]
base-files: uci-defaults: do config flush in one shot
Moving a file between tmpfs and other fs is neither
faster nor safer, thus no point in doing it in two steps.
Use new jshn option to write output directly to file.
Originally discussed here:
http://lists.openwrt.org/pipermail/openwrt-devel/2017-December/010127.html
Petr Štetiar [Mon, 21 Oct 2019 08:37:51 +0000 (10:37 +0200)]
urngd: update to latest Git head
* 40f939d57c67 Tag version 1.0.1
* 9e758e6e6aec jitterentropy-rngd: update to version v1.1.0 + clang compile fix
* 193586a25adc Fix wrong types in format strings used in debug build
* d474977bb611 Add initial GitLab CI support
This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
ramips: remove RAM size from device name for UniElec devices
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.
Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath79: base-files: disable sysupgrade for routerstations and ja76pf2
Previous commit 0cc87b3 "ath79: image: disable sysupgrade images for
routerstations and ja76pf2" doesn't remedy completely the posibility of
bricking the device, since user could try to downgrade with an older
image. Therefore disable sysupgrade code for these boards with a small
note.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Paul Spooren [Tue, 24 Sep 2019 22:32:56 +0000 (12:32 -1000)]
build: add script to sign packages
This script allows image signing indipendend of the actual build
process, to run on a master server after receiving freshly backed
images. Idea is to avoid storying private keys on third party builders
while still beeing to be able to sign packages.
Run ./scripts/sign_images.sh with the following env vars:
* TOP_DIR where to search for sysupgrade.bin images
* BUILD_KEY place of key-build{,.pub,.ucert}
* REMOVE_OTHER_SIGNATURES removes signatures added by e.g. buildbots
Only sysupgrade.bin files are touched as factory.bin signatures wouldn't
be evaluated on stock from.
Paul Spooren [Tue, 24 Sep 2019 22:32:54 +0000 (12:32 -1000)]
build: separate signing logic
This separates the options for signature creation and verification
* SIGNED_PACKAGES create Packages.sig
* SIGNED_IMAGES add ucert signature to created images
* CHECK_SIGNATURE add verification capabilities to images
* INSTALL_LOCAL_KEY add local key-build to /etc/opkg/keys
Right now the buildbot.git contains some hacks to create images that
have signature verification capabilities while not storing private keys
on buildbot slaves. This commit allows to disable these steps for the
buildbots and only perform signing on the master.
ath79: fix SUPPORTED_DEVICES for ubnt_nanostation-m
The ar71xx images for the Ubiquiti NanoStation M (XM) devices use
"nanostation-m" as board name, but the ath79 images are only
compatible with the "nano-m" board name, so sysupgrade complains.
By changing this additional supported device, sysupgrade smoothly
upgrades from ar71xx to ath79.
Ref: openwrt#2418
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
lantiq: modify ath9k caldata extraction to reuse caldata.sh
In lantiq, ath9k caldata extraction is implemented to work in two
alternate "modes", the standard one and another one with swapped
byte pairs.
This rearranges the functions so "standard" use is based on the
caldata.sh library, while only a single local function is required
for the special case.
Note that while the parameter for switching between normal and swab
is removed, the size of the caldata is added to the function calls
to stay consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
image: add magic number option for append-uImage-fakehdr
'append-uImage-fakehdr' can now accept magic number as a second, optional
parameter (passed directly to 'mkimage' command with '-M' option). This
enables construction of proper Netgear-specific fake rootfs images
(required for flashing WNDR4300 for example).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Change WAN LED behaviour to be consistent with other Netgear
routers running OpenWrt. Instead of link speed, use amber colour
to indicate link status. Green LED should be used when Internet
connection is up and running.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
ath79: fix patching ath9k MAC address for MyNet WiFi Range Extender
The code line patching ath9k MAC address for this device contains
a wrong number of arguments including an unset "$mac", which
looks like a typo or copy/paste mistake.
This has been introduced already in the device support commit 745dee11ac78 ("ath79: add support for WD My Net Wi-Fi Range
Extender").
This patch just removes the "$mac" argument, leaving a formally
valid line. (No on-device test has been performed.)
Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds ath79 support for Netgear WNR1000v2.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.
Specification
=============
* Description: Netgear WNR1000 v2
* Loader: U-boot
* SOC: Atheros AR7240 (340 MHz)
* RAM: 32 MiB
* Flash: 4 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 3712 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9285)
* USB: no
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
This patch adds ath79 support for Netgear WNR2000v3.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.
Specification
=============
* Description: Netgear WNR2000 v3
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 32 MiB
* Flash: 4 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 3712 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: no
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
This patch improves ath79 support for Netgear WNR612v2.
Router functionality becomes identical to ar71xx version.
Changes include:
* software control over LAN LEDs via sysfs
* correct MAC addresses for network interfaces
* correct image size in device definition
* dts: 'keys' renamed to 'ath9k-keys'
* dts: 'label-mac-device' set to eth1 (LAN)
* dts: formatting adjustments
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
ath79: add LAN LEDs control bits for AR724x GPIO function pinmux
Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit.
This patch adds new DTS settings to control LAN LEDs and CLKs that allow
full software control over these diodes - exactly the same is done by ar71xx
target in device setup phase for many routers (WNR2000v3 for example).
'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits.
'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and
AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along
with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and
buttons on device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
router.
Specification
SoC: Atheros AR1022
RAM: 64 MB DDR2
Flash: 8 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled, 5x switch
Buttons: 2x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Known issues
5GHz LED doesn't work
Additional information
When TX line on UART is connected, and board is switched on from power
off state, the DDR memory training may fail.
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), which may or may
not work with introduced images.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Kristian Evensen [Sun, 20 Oct 2019 09:33:13 +0000 (11:33 +0200)]
ipq40xx: Add support for Unielec U4019
This commit adds support for the 32MB storage/512MB RAM version of the U4019
IPQ4019-based board from Unielec. The board has the following specifications:
In order to install OpenWRT on the U4019, you need to go via the
initramfs-image. The installation steps are as follows:
* Connect to board via serial (header exposed and clearly marked).
* Interrupt bootloader by pressing a button.
* Copy the initramfs-image to your tftp folder, call the file C0A80079.img.
* Give the network interface connected to the U4019 the address
192.168.0.156/24.
* Start your tftp-server and run tftpboot on the board.
* Run bootm when the file has been transferred, to boot OpenWRT.
* Once OpenWRT has booted, copy the sysupgrade-image to the device and run
sysupgrade to install OpenWRT on the U4019.
Notes:
- Since IPQ4019 has been moved to 4.19, I have not added support for kernel
4.14.
- There is a bug with hardware encryption on IPQ4019, causing poor performance
with TCP and ipsec (see for example FS#2355). In order to improve performance,
I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if
bug is fixed.
- In order for Ethernet to work, the phy has to be reset by setting gpio 47
low/high. Adding support for phy reset via gpio required patching the
mdio-driver, and the code added comes from the vendor driver. I do not know if
patching the driver is an acceptable approach or not.
v1->v2:
* Do not use wildcard as identifier in the board.d-scripts (thanks
Adrian Schmutzler).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.
Also fix the phy-mode to represent the actual state needed for ethernet
to function.
Reported-by: Moritz Schreiber <moritz@mosos.de> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property] Signed-off-by: David Bauer <mail@david-bauer.net>
Yousong Zhou [Fri, 18 Oct 2019 12:10:06 +0000 (12:10 +0000)]
libpcap: build with cmake
The main motivation is to drop and stop maintaining
"100-debian_shared_lib.patch". It lacks the logic to include custom
implementation of several functions like pcap_strlcpy() which can cause
build failures when glibc is used [2]
CAN and CAN-USB support related symbols are now handled by general linux
support, see [1]
"-ffunction-sections -fdata-sections" were removed as they should help
much for shared libraries
Size comparison before and after the change
-rw-r--r-- 1 yunion yunion 238042 Oct 18 11:42 ipkg-x86_64/libpcap/usr/lib/libpcap.so.1
lrwxrwxrwx 1 yunion yunion 16 Oct 18 13:03 ipkg-x86_64/libpcap/usr/lib/libpcap.so.1 -> libpcap.so.1.9.1
-rwxr-xr-x 1 yunion yunion 229867 Oct 18 13:03 ipkg-x86_64/libpcap/usr/lib/libpcap.so.1.9.1
[1] On Linux, handle all CAN captures with pcap-linux.c, in cooked mode,
https://github.com/the-tcpdump-group/libpcap/commit/93ca5ff7030aaf1219e1de05ec89a68384bfc50b
[2] https://github.com/openwrt/packages/issues/10270
This patch contains updated driver for Atheros NAND Flash Controller
written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc').
ath79 version has adapted to work with kernel 4.19 and Device Tree.
It has also been renamed to 'ar934x-nand' to avoid confusion with
Near-Field Communication technology.
Controller is present on Atheros AR934x SoCs and required for accessing
internal flash storage on routers like Netgear WNDR4300.
This port preserves all NAND programming code while moving platform
configuration to Device Tree and replacing some kernel functions marked
for retirement by 4.19.
Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section).
Most important changes to ar71xx version are:
* old kernel sections of code removed
* 'bool swap_dma' provided by platform data is now set by boolean DT
property 'qca,nand-swap-dma'
* board-supplied (mach-*.c code) platform data removed - its elements
become either unused, redundant or replaced by DT methods (like reset)
* IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore
* calls to deprecated nand_scan_ident() + nand_scan_tail() function pair
replaced by using recommended nand_scan() with attach_chip() callback
* ECC is set to hardware by default, can be overriden by standard DT
'nand-ecc-*' properties (software Hamming or BCH are other options)
This driver has been successfully tested on Netgear WNDR4300 running
experimental ath79 OpenWrt master branch.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[add reset control] Signed-off-by: David Bauer <mail@david-bauer.net>
Masafumi UTSUGI [Tue, 1 Oct 2019 09:59:18 +0000 (18:59 +0900)]
ipq40xx: essedma: Fix dead lock
edma_read_append_stats() gets called from two places in the driver.
The first place is the kernel timer that periodically updates
the statistics, so nothing gets lost due to overflows.
The second one it's part of the userspace ethtool ioctl handler
to provide up-to-date values.
For this configuration, the use of spin_lock() is not sufficient
and as per:
<https://mirrors.edge.kernel.org/pub/linux/kernel/people/rusty/kernel-locking/c214.html>
the locking has to be upgraded to spin_lock_bh().
Signed-off-by: Masafumi UTSUGI <mutsugi@allied-telesis.co.jp>
[folded patch into 710-, rewrote message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds engine configuration sections to openssl.cnf, with a commented
list of engines. To enable an engine, all you have to do is uncomment
the engine line.
It also adds some useful comments to the devcrypto engine configuration
section. Other engines currently don't have configuration commands.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Josef Schlehofer [Sat, 19 Oct 2019 16:50:44 +0000 (18:50 +0200)]
strace: update to version 5.3
Makefile changes:
- moves PKG_MAINTAINER above PKG_LICENSE
- Change PKG_LICENSE to LGPL-2.1-or-later and correct PKG_LICENSE_FILES
- changes URL to a more appropriate one, which uses HTTPS
- adds 2 spaces as an indentation in description
Compile and run tested on Turris Omnia, mvebu
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Hauke Mehrtens [Sat, 19 Oct 2019 21:16:04 +0000 (23:16 +0200)]
kernel: Fix arm64 include files
This patch fixes the build of gdb and strace on arm64 targets with
kernel 4.19.
Without this patch asm/ptrace.h is including asm/sigcontext.h and this
file defines some structures which are also defined in musl header file
arch/aarch64/bits/signal.h. These two definitions then conflict with
each other and make the build fail.
This was seen locally and also by the build bot. The struct sigcontext,
struct sve_context and some others were defined twice. It looks like
this problem was introduced between 4.14 and 4.19 and it was fixed in
5.0. I already requested to backport this patch to kernel 4.19.
Biwen Li [Mon, 14 Oct 2019 04:42:32 +0000 (12:42 +0800)]
kernel: layerscape: fix compilation error
This fixes a compilation error as follows:
drivers/staging/fsl_qbman/qman_config.c:815:29: error: bitwise comparison
always evaluates to false [-Werror=tautological-compare]
if ((qman_ip_rev & 0xFF00) == QMAN_REV31) {
projects / thirdparty / openwrt.git / log
