The testcase verifies the setting of different fields in Monitor Mode
Control Register A (MMCRA). In the current code, EV_CODE_EXTRACT macro
is used to extract the "sample" field, which then needs to be further
processed to fetch rand_samp_elig and rand_samp_mode bits. But the
current code is not passing valid sample field to EV_CODE_EXTRACT
macro. Patch addresses this by fixing the input for EV_CODE_EXTRACT.
When dev_err_probe() is called, 'ret' holds the value of the previous
successful devm_request_irq() call.
'ret' should be assigned with a meaningful value before being used in
dev_err_probe().
While at it, use and return "PTR_ERR(ctrl->clk)" instead of a hard-coded
"-ENOENT" so that -EPROBE_DEFER is handled and propagated correctly.
Fixes: 81b63420564d ("fbdev: mmp: Make use of the helper function dev_err_probe()") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In virtio_net, if we disable napi_tx, when we trigger a tx interrupt,
the vq->event_triggered will be set to true. It is then never reset
until we explicitly call virtqueue_enable_cb_delayed or
virtqueue_enable_cb_prepare.
If we disable the napi_tx, virtqueue_enable_cb* will only be called when
the tx ring is getting relatively empty.
Since event_triggered is true, VRING_AVAIL_F_NO_INTERRUPT or
VRING_PACKED_EVENT_FLAG_DISABLE will not be set. As a result we update
vring_used_event(&vq->split.vring) or vq->packed.vring.driver->off_wrap
every time we call virtqueue_get_buf_ctx. This causes more interrupts.
To summarize:
1) event_triggered was set to true in vring_interrupt()
2) after this nothing will happen in virtqueue_disable_cb() so
VRING_AVAIL_F_NO_INTERRUPT is not set in avail_flags_shadow
3) virtqueue_get_buf_ctx_split() will still think the cb is enabled
and then it will publish a new event index
To fix:
update VRING_AVAIL_F_NO_INTERRUPT or VRING_PACKED_EVENT_FLAG_DISABLE in
the vq when we call virtqueue_disable_cb even when event_triggered is
true.
Tested with iperf:
iperf3 tcp stream:
vm1 -----------------> vm2
vm2 just receives tcp data stream from vm1, and sends acks to vm1,
there are many tx interrupts in vm2.
with the patch applied there are just a few tx interrupts.
v2->v3:
-update the interrupt disable flag even with the event_triggered is set,
-instead of checking whether event_triggered is set in
-virtqueue_get_buf_ctx_{packed/split}, will cause the drivers which have
-not called virtqueue_{enable/disable}_cb to miss notifications.
v3->v4:
-remove change for
-"if (vq->packed.event_flags_shadow != VRING_PACKED_EVENT_FLAG_DISABLE)"
-in virtqueue_disable_cb_packed
Fixes: 8d622d21d248 ("virtio: fix up virtio_disable_cb") Signed-off-by: Albert Huang <huangjie.albert@bytedance.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230329102300.61000-1-huangjie.albert@bytedance.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing a SPMI driver, there can be a crash due to NULL pointer
dereference if it does not have a remove callback defined. This is
one such call trace observed when removing the QCOM SPMI PMIC driver:
If a driver has all its resources allocated through devm_() APIs and
does not need any other explicit cleanup, it would not require a
remove callback to be defined. Hence, add a check for remove callback
presence before calling it when removing a SPMI driver.
When loading the driver for rtl8192e, the W_DISABLE# switch is working as
intended. But when the WLAN is turned off in software and then turned on
again the W_DISABLE# does not work anymore. Reason for this is that in
the function _rtl92e_dm_check_rf_ctrl_gpio() the bfirst_after_down is
checked and returned when true. bfirst_after_down is set true when
switching the WLAN off in software. But it is not set to false again
when WLAN is turned on again.
Add bfirst_after_down = false in _rtl92e_sta_up to reset bit and fix
above described bug.
Fixes: 94a799425eee ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek") Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/20230418200201.GA17398@matrix-ESPRIMO-P710 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Also get rid of conditional compilation based on CONFIG_PM_SLEEP because
it introduces build issues with certain configs when CQSPI_DEV_PM_OPS is
just NULL.
When handle qmu transfer irq, it will unlock @mtu->lock before give back
request, if another thread handle disconnect event at the same time, and
try to disable ep, it may lock @mtu->lock and free qmu ring, then qmu
irq hanlder may get a NULL gpd, avoid the KE by checking gpd's value before
handling it.
e.g.
qmu done irq on cpu0 thread running on cpu1
qmu_done_tx()
handle gpd [0]
mtu3_requ_complete() mtu3_gadget_ep_disable()
unlock @mtu->lock
give back request lock @mtu->lock
mtu3_ep_disable()
mtu3_gpd_ring_free()
unlock @mtu->lock
lock @mtu->lock
get next gpd [1]
[1]: goto [0] to handle next gpd, and next gpd may be NULL.
Commit ac82b56bda5f ("usb: gadget: tegra-xudc: Add vbus_draw support")
populated the vbus_draw callback for the Tegra XUDC driver. The function
tegra_xudc_gadget_vbus_draw(), that was added by this commit, assumes
that the pointer 'curr_usbphy' has been initialised, which is not always
the case because this is only initialised when the USB role is updated.
Fix this crash, by checking that the 'curr_usbphy' is valid before
dereferencing.
The Store Queue code allocates a bitmap buffer with the size of
multiple of sizeof(long) in sq_api_init(). While the buffer size
is calculated correctly, the code uses the wrong element size to
allocate the buffer which results in the allocated bitmap buffer
being too small.
Fix this by allocating the buffer with kcalloc() with element size
sizeof(long) instead of kzalloc() whose elements size defaults to
sizeof(char).
Fixes: d7c30c682a27 ("sh: Store Queue API rework.") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Link: https://lore.kernel.org/r/20230419114854.528677-1-glaubitz@physik.fu-berlin.de Signed-off-by: Sasha Levin <sashal@kernel.org>
typeof is (still) a GNU extension, which means that it cannot be used when
building ISO C (e.g. -std=c99). It should therefore be avoided in uapi
headers in favour of the ISO-friendly __typeof__.
Unfortunately this issue could not be detected by
CONFIG_UAPI_HEADER_TEST=y as the __ALIGN_KERNEL() macro is not expanded in
any uapi header.
This matters from a userspace perspective, not a kernel one. uapi
headers and their contents are expected to be usable in a variety of
situations, and in particular when building ISO C applications (with
-std=c99 or similar).
This particular problem can be reproduced by trying to use the
__ALIGN_KERNEL macro directly in application code, say:
#include <linux/const.h>
int align(int x, int a)
{
return __KERNEL_ALIGN(x, a);
}
and trying to build that with -std=c99.
Link: https://lkml.kernel.org/r/20230411092747.3759032-1-kevin.brodsky@arm.com Fixes: a79ff731a1b2 ("netfilter: xtables: make XT_ALIGN() usable in exported headers by exporting __ALIGN_KERNEL()") Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com> Reported-by: Ruben Ayrapetyan <ruben.ayrapetyan@arm.com> Tested-by: Ruben Ayrapetyan <ruben.ayrapetyan@arm.com> Reviewed-by: Petr Vorel <pvorel@suse.cz> Tested-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If CONFIG_DEBUG_INFO_REDUCED is enabled in the kernel configuration, we
will typically not be able to load vmlinux-gdb.py and will fail with:
Traceback (most recent call last):
File "/home/fainelli/work/buildroot/output/arm64/build/linux-custom/vmlinux-gdb.py", line 25, in <module>
import linux.utils
File "/home/fainelli/work/buildroot/output/arm64/build/linux-custom/scripts/gdb/linux/utils.py", line 131, in <module>
atomic_long_counter_offset = atomic_long_type.get_type()['counter'].bitpos
KeyError: 'counter'
Rather be left wondering what is happening only to find out that reduced
debug information is the cause, raise an eror. This was not typically a
problem until e3c8d33e0d62 ("scripts/gdb: fix 'lx-dmesg' on 32 bits arch")
but it has since then.
Link: https://lkml.kernel.org/r/20230406215252.1580538-1-f.fainelli@gmail.com Fixes: e3c8d33e0d62 ("scripts/gdb: fix 'lx-dmesg' on 32 bits arch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Antonio Borneo <antonio.borneo@foss.st.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: John Ogness <john.ogness@linutronix.de> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Petr Mladek <pmladek@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The xiic_xfer() function gets a runtime PM reference when the function is
entered. This reference is released when the function is exited. There is
currently one error path where the function exits directly, which leads to
a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: fdacc3c7405d ("i2c: xiic: Switch from waitqueue to completion") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cdns_i2c_master_xfer() function gets a runtime PM reference when the
function is entered. This reference is released when the function is
exited. There is currently one error path where the function exits
directly, which leads to a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
The cadence QSPI driver misbehaves after performing a full system suspend
resume:
...
spi-nor spi0.0: resume() failed
...
This results in a flash connected via OSPI interface after system suspend-
resume to be unusable.
fix these suspend and resume functions.
Fixes: 140623410536 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller") Signed-off-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20230417091027.966146-3-d-gole@ti.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 5dd45b66742a ("drm/panel: novatek-nt35950: Improve error handling")
introduced logic to unregister DSI1 on any sort of probe failure, as
that's not done automatically by kernel APIs.
It did not however account for cases where only one DSI host is used.
Fix that.
Fixes: 5dd45b66742a ("drm/panel: novatek-nt35950: Improve error handling") Reported-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230417-topic-maple_panel_fixup-v1-1-07c8db606f5e@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Assignment of NVIDIA Ampere-based GPUs have seen a regression since the
below referenced commit, where the reduced D3hot transition delay appears
to introduce a small window where a D3hot->D0 transition followed by a bus
reset can wedge the device. The entire device is subsequently unavailable,
returning -1 on config space read and is unrecoverable without a host
reset.
This has been observed with RTX A2000 and A5000 GPU and audio functions
assigned to a Windows VM, where shutdown of the VM places the devices in
D3hot prior to vfio-pci performing a bus reset when userspace releases the
devices. The issue has roughly a 2-3% chance of occurring per shutdown.
Restoring the HDA controller d3hot_delay to the effective value before the
below commit has been shown to resolve the issue. NVIDIA confirms this
change should be safe for all of their HDA controllers.
of_node_put() should have been done directly after
mqs_priv->regmap = syscon_node_to_regmap(gpr_np);
otherwise it creates a reference leak on the success path.
To fix this, of_node_put() is moved to the correct location, and change
all the gotos to direct returns.
Fixes: a9d273671440 ("ASoC: fsl_mqs: Fix error handling in probe") Signed-off-by: Liliang Ye <yll@hust.edu.cn> Reviewed-by: Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/r/20230403152647.17638-1-yll@hust.edu.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In a very peculiar case when probing and registering with the secondary
DSI host succeeds, but the OF backlight or DSI attachment fails, the
primary DSI device is automatically cleaned up, but the secondary one
is not, leading to -EEXIST when the driver core tries to handle
-EPROBE_DEFER.
Unregister the DSI1 device manually on failure to prevent that.
If there is no ACPI/DT information, it is assumed that L1 caches
are private and L2 (and higher) caches are shared. A cache is
'shared' between two CPUs if it is accessible from these two
CPUs.
Each CPU owns a representation (i.e. has a dedicated cacheinfo struct)
of the caches it has access to. cache_leaves_are_shared() tries to
identify whether two representations are designating the same actual
cache.
In cache_leaves_are_shared(), if 'this_leaf' is a L2 cache (or higher)
and 'sib_leaf' is a L1 cache, the caches are detected as shared as
only this_leaf's cache level is checked.
This is leads to setting sib_leaf as being shared with another CPU,
which is incorrect as this is a L1 cache.
Check 'sib_leaf->level'. Also update the comment as the function is
called when populating 'shared_cpu_map'.
Fixes: f16d1becf96f ("cacheinfo: Use cache identifiers to check if the caches are shared if available") Signed-off-by: Pierre Gondois <pierre.gondois@arm.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20230414081453.244787-2-pierre.gondois@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on num_hid_devices, each sensor device is initialized. If
"no sensors" is initialized, amd_sfh work initialization and scheduling
doesn’t make sense and returns EOPNOTSUPP to stop driver probe. Hence,
add a check for "no sensors" enabled to handle the special case.
The initialization of SFH1.1 sensors may take some time. Hence, increase
sensor command timeouts in order to obtain status responses within a
maximum timeout.
As soon as the system is booted after shutdown, the sensors may remain in
a weird state and fail to initialize. Therefore, all sensors should be
turned off during shutdown.
Fixes: 4f567b9f8141 ("SFH: PCIe driver to add support of AMD sensor fusion hub") Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Illuminance value is actually 32 bits, but is incorrectly trancated to
16 bits. Hence convert to integer illuminace accordingly to reflect
correct values.
In order to start or stop sensors, the firmware command needs to be
changed to add an additional default subcommand value. For this reason,
add a subcommand value to enable or disable sensors accordingly.
Avoid generating an exception if there are no generic power domain(s)
registered:
(gdb) lx-genpd-summary
domain status children
/device runtime status
----------------------------------------------------------------------
Python Exception <class 'gdb.error'>: No symbol "gpd_list" in current context.
Error occurred in Python: No symbol "gpd_list" in current context.
(gdb) quit
Avoid generating an exception if there are no clocks registered:
(gdb) lx-clk-summary
enable prepare protect
clock count count count rate
------------------------------------------------------------------------
Python Exception <class 'gdb.error'>: No symbol "clk_root_list" in
current context.
Error occurred in Python: No symbol "clk_root_list" in current context.
Link: https://lkml.kernel.org/r/20230323225246.3302977-1-f.fainelli@gmail.com Fixes: d1e9710b63d8 ("scripts/gdb: initial clk support: lx-clk-summary") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_PROC_FS is not set, proc_salinfo_show() is not used. Mark the
function as __maybe_unused to quieten the warning message.
../arch/ia64/kernel/salinfo.c:584:12: warning: 'proc_salinfo_show' defined but not used [-Wunused-function]
584 | static int proc_salinfo_show(struct seq_file *m, void *v)
| ^~~~~~~~~~~~~~~~~
Link: https://lkml.kernel.org/r/20230223034309.13375-1-rdunlap@infradead.org Fixes: 3f3942aca6da ("proc: introduce proc_create_single{,_data}") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
alloc_per_cpu_data() is called by find_memory(), which is marked as
__init. Therefore alloc_per_cpu_data() can also be marked as __init to
remedy this modpost problem.
Link: https://lkml.kernel.org/r/20230223034258.12917-1-rdunlap@infradead.org Fixes: 4b9ddc7cf272 ("[IA64] Fix section mismatch in contig.c version of per_cpu_init()") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During EDR recovery, the OS must clear error status of the port that
triggered DPC even if firmware retains control of DPC and AER (see the
implementation note in the PCI Firmware spec r3.3, sec 4.6.12).
Prior to 068c29a248b6 ("PCI/ERR: Clear PCIe Device Status errors only if
OS owns AER"), the port Device Status was cleared in this path:
After 068c29a248b6, pcie_do_recovery() no longer clears Device Status when
firmware controls AER, so the error bit remains set even after recovery.
Per the "Downstream Port Containment configuration control" bit in the
returned _OSC Control Field (sec 4.5.1), the OS is allowed to clear error
status until it evaluates _OST, so clear Device Status in
edr_handle_event() if the error recovery was successful.
[bhelgaas: commit log] Fixes: 068c29a248b6 ("PCI/ERR: Clear PCIe Device Status errors only if OS owns AER") Link: https://lore.kernel.org/r/20230315235449.1279209-1-sathyanarayanan.kuppuswamy@linux.intel.com Reported-by: Tsaur Erwin <erwin.tsaur@intel.com> Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The helper generating an OF based modalias (of_device_get_modalias())
works fine, but due to the use of snprintf() internally it needs a
buffer one byte longer than what should be needed just for the entire
string (excluding the '\0'). Most users of this helper are sysfs hooks
providing the modalias string to users. They all provide a PAGE_SIZE
buffer which is way above the number of bytes required to fit the
modalias string and hence do not suffer from this issue.
There is another user though, of_device_request_module(), which is only
called by drivers/usb/common/ulpi.c. This request module function is
faulty, but maybe because in most cases there is an alternative, ULPI
driver users have not noticed it.
In this function, of_device_get_modalias() is called twice. The first
time without buffer just to get the number of bytes required by the
modalias string (excluding the null byte), and a second time, after
buffer allocation, to fill the buffer. The allocation asks for an
additional byte, in order to store the trailing '\0'. However, the
buffer *length* provided to of_device_get_modalias() excludes this extra
byte. The internal use of snprintf() with a length that is exactly the
number of bytes to be written has the effect of using the last available
byte to store a '\0', which then smashes the last character of the
modalias string.
Provide the actual size of the buffer to of_device_get_modalias() to fix
this issue.
Note: the "str[size - 1] = '\0';" line is not really needed as snprintf
will anyway end the string with a null byte, but there is a possibility
that this function might be called on a struct device_node without
compatible, in this case snprintf() would not be executed. So we keep it
just to avoid possible unbounded strings.
Cc: Stephen Boyd <sboyd@kernel.org> Cc: Peter Chen <peter.chen@kernel.org> Fixes: 9c829c097f2f ("of: device: Support loading a module with OF based modalias") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20230404172148.82422-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
if (vmci_host_dev->ct_type == VMCIOBJ_CONTEXT) {
// Dereferencing the wrong pointer
poll_wait(..., &context->host_context);
}
In this scenario, vmci_host_poll() reads vmci_host_dev->context first,
and then reads vmci_host_dev->ct_type to check that
vmci_host_dev->context is initialized. However, since these two reads
are not atomically executed, there is a chance of a race condition as
described above.
To fix this race condition, read vmci_host_dev->context after checking
the value of vmci_host_dev->ct_type so that vmci_host_poll() always
reads an initialized context.
Reported-by: Dae R. Jeong <threeearcat@gmail.com> Fixes: 8bf503991f87 ("VMCI: host side driver implementation.") Signed-off-by: Dae R. Jeong <threeearcat@gmail.com> Link: https://lore.kernel.org/r/ZCGFsdBAU4cYww5l@dragonet Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
CPM has the same problem as QE so for CPM also use the fix added
by commit 0398fb70940e ("spi/spi_mpc8xxx: Fix QE mode Litte Endian"):
CPM mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for 16 and 32 bits
words. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also limit the workaround to 16 and 32 bits words because it can
only work for multiples of 8-bits.
pci1xxxx_spi_resume API masks SPI interrupt bit which prohibits interrupt
from coming to the host at the end of the transaction after suspend-resume.
This patch unmasks this bit at resume.
Fixes: 1cc0cbea7167 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch") Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Link: https://lore.kernel.org/r/20230404171613.1336093-3-tharunkumar.pasumarthi@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pci1xxxx_spi_transfer_one API, length of SPI transaction gets cleared
by setting of length mask. Set length of transaction only after masking
length field.
Fixes: 1cc0cbea7167 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch") Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Link: https://lore.kernel.org/r/20230404171613.1336093-2-tharunkumar.pasumarthi@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Any power domain would already have been attached by the platform bus
code so drop the bogus power domain attach which always succeeds from
probe.
This effectively reverts commit 7de109c0abe9 ("interconnect: icc-rpm:
Add support for bus power domain").
Fixes: 7de109c0abe9 ("interconnect: icc-rpm: Add support for bus power domain") Cc: Yassine Oudjana <y.oudjana@protonmail.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # MSM8996 Sony Kagura Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230313084953.24088-3-johan+linaro@kernel.org Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
The driver is able to work fine without relying on a mandatory interrupt
being assigned to the I2C device. This is only needed when making use of
the jack-detect support.
However, the following warning message is always emitted when there is
no such interrupt available:
es8316 0-0011: Failed to get IRQ 0: -22
Do not attempt to request an IRQ if it is not available/valid. This also
ensures the rather misleading message is not displayed anymore.
Also note the IRQ validation relies on commit dab472eb931bc291 ("i2c /
ACPI: Use 0 to indicate that device does not have interrupt assigned").
Fixes: 822257661031 ("ASoC: es8316: Add jack-detect support") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230328094901.50763-1-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bb38919ec56e ("PCI: imx6: Add support for i.MX6 PCIe controller")
added a fault hook to this driver in the probe function. So it was only
installed if needed.
commit bde4a5a00e76 ("PCI: imx6: Allow probe deferral by reset GPIO")
moved it from probe to driver init which installs the hook unconditionally
as soon as the driver is compiled into a kernel.
When this driver is compiled as a module, the hook is not registered
until after the driver has been matched with a .compatible and
loaded.
commit 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ")
added some protection for non-ARM architectures, but this does not
protect non-i.MX ARM architectures.
Since fault handlers can be triggered on any architecture for different
reasons, there is no guarantee that they will be triggered only for the
assumed situation, leading to improper error handling (i.MX6-specific
imx6q_pcie_abort_handler) on foreign systems.
I had seen strange L3 imprecise external abort messages several times on
OMAP4 and OMAP5 devices and couldn't make sense of them until I realized
they were related to this unused imx6q driver because I had
CONFIG_PCI_IMX6=y.
Note that CONFIG_PCI_IMX6=y is useful for kernel binaries that are designed
to run on different ARM SoC and be differentiated only by device tree
binaries. So turning off CONFIG_PCI_IMX6 is not a solution.
Therefore we check the compatible in the init function before registering
the fault handler.
Link: https://lore.kernel.org/r/e1bcfc3078c82b53aa9b78077a89955abe4ea009.1678380991.git.hns@goldelico.com Fixes: bde4a5a00e76 ("PCI: imx6: Allow probe deferral by reset GPIO") Fixes: 415b6185c541 ("PCI: imx6: Fix config read timeout handling") Fixes: 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit bbf7d3b1c4f40 ("ASoC: soc-pcm: align BE 'atomicity' with
that of the FE") BE and FE atomicity must match.
In the case of Compress PCM there is a mismatch in atomicity between FE
and BE and we get errors like this:
[ 36.434566] sai1-wm8960-hifi: dpcm_be_connect: FE is atomic but BE
is nonatomic, invalid configuration
[ 36.444278] PCM Deep Buffer: ASoC: can't connect SAI1.OUT
In order to fix this we must inherit the atomicity from DAI link
associated with current PCM Compress FE.
Fixes: bbf7d3b1c4f4 ("ASoC: soc-pcm: align BE 'atomicity' with that of the FE") Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20230324124019.30826-1-daniel.baluta@oss.nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The usb3->role_sw could be freed under such circumstance and then
used in usb_role_switch_set_role.
This bug was found by static analysis. And note that removing a
driver is a root-only operation, and should never happen in normal
case. But the root user may directly remove the device which
will also trigger the remove function.
Fix it by canceling the work before cleanup in the renesas_usb3_remove.
Fixes: 39facfa01c9f ("usb: gadget: udc: renesas_usb3: Add register of usb role switch") Signed-off-by: Zheng Wang <zyytlz.wz@163.com> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20230320062931.505170-1-zyytlz.wz@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use kunmap_local() to unmap pages locally mapped with kmap_local_page().
kunmap_local() must be called on the kernel virtual address returned by
kmap_local_page(), differently from how we use kunmap() which instead
expects the mapped page as its argument.
In module_zstd_decompress() we currently map with kmap_local_page() and
unmap with kunmap(). This breaks the code and so it should be fixed.
Cc: Piotr Gorski <piotrgorski@cachyos.org> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Ira Weiny <ira.weiny@intel.com> Fixes: 169a58ad824d ("module/decompress: Support zstd in-kernel decompression") Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Piotr Gorski <piotrgorski@cachyos.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .supports_op() callback function returns true by default after
performing driver-specific checks. Therefore the driver cannot apply
the buswidth in devicetree.
Call spi_mem_default_supports_op() helper to handle the buswidth
in devicetree.
The commit 4529992c9474 ("interconnect: qcom: osm-l3: Use
platform-independent node ids") made osm-l3 driver use
platform-independent IDs, removing the need to include platform headers.
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
Fixes: d593574aff0a ("spi: imx: do not access registers while clocks disabled") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230306065733.2170662-2-u.kleine-koenig@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An early error exit in atmel_qspi_remove() doesn't prevent the device
unbind. So this results in an spi controller with an unbound parent
and unmapped register space (because devm_ioremap_resource() is undone).
So using the remaining spi controller probably results in an oops.
Instead unregister the controller unconditionally and only skip hardware
access and clk disable.
Also add a warning about resume failing and return zero unconditionally.
The latter has the only effect to suppress a less helpful error message by
the spi core.
The arbitration of the UART DMA is mishandled for a few
exceptional cases when probing and releasing the driver.
It is possible that the DMA register spaces are not defined in
device tree for an instance of the driver, so attempts to access
the registers in brcmuart_arbitration() would use NULL pointers.
It is also possible for the probe function to return an error
while still holding the UART DMA. This would prevent the UART
DMA from being claimed by an instance that could use it.
These errors are addressed by only releasing the UART DMA if it
is held by this instance (i.e. priv->dma_enabled == 1) and
directing early error paths in probe to this common release_dma
handling.
The stm32_usart_transmit_chars() may be called with empty or stopped
transmit queue, and no XON/OFF character pending. This can happen at
the end of transmission, where this last call is used to either handle
the XON/XOFF x_char, or disable TX interrupt if queue is empty or
stopped.
If that occurs, do not assert the RS485 RTS/DE GPIO anymore, as the
GPIO would remain asserted past the end of transmission and that would
block the RS485 bus after the transmission.
Only assert the RS485 RTS/DE GPIO if there is either pending XON/XOFF
x_char, or at least one character in running transmit queue.
Fixes: d7c76716169d ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode") Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20230223042252.95480-2-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
So while priority inversion on the pmsg_lock is an occasional
problem that an rt_mutex would help with, in uses where logging
is writing to pmsg heavily from multiple threads, the pmsg_lock
can be heavily contended.
After this change landed, it was reported that cases where the
mutex locking overhead was commonly adding on the order of 10s
of usecs delay had suddenly jumped to ~msec delay with rtmutex.
It seems the slight differences in the locks under this level
of contention causes the normal mutexes to utilize the spinning
optimizations, while the rtmutexes end up in the sleeping
slowpath (which allows additional threads to pile on trying
to take the lock).
In this case, it devolves to a worse case senerio where the lock
acquisition and scheduling overhead dominates, and each thread
is waiting on the order of ~ms to do ~us of work.
Obviously, having tons of threads all contending on a single
lock for logging is non-optimal, so the proper fix is probably
reworking pstore pmsg to have per-cpu buffers so we don't have
contention.
Additionally, Steven Rostedt has provided some furhter
optimizations for rtmutexes that improves the rtmutex spinning
path, but at least in my testing, I still see the test tripping
into the sleeping path on rtmutexes while utilizing the spinning
path with mutexes.
But in the short term, lets revert the change to the rt_mutex
and go back to normal mutexes to avoid a potentially major
performance regression. And we can work on optimizations to both
rtmutexes and finer-grained locking for pstore pmsg in the
future.
Cc: Wei Wang <wvw@google.com> Cc: Midas Chien<midaschieh@google.com> Cc: "Chunhui Li (李春辉)" <chunhui.li@mediatek.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Kees Cook <keescook@chromium.org> Cc: Anton Vorontsov <anton@enomsg.org> Cc: "Guilherme G. Piccoli" <gpiccoli@igalia.com> Cc: Tony Luck <tony.luck@intel.com> Cc: kernel-team@android.com Fixes: 76d62f24db07 ("pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion") Reported-by: "Chunhui Li (李春辉)" <chunhui.li@mediatek.com> Signed-off-by: John Stultz <jstultz@google.com> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20230308204043.2061631-1-jstultz@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit cc7ad0d77b51 ("drivers: staging: rtl8723bs: Fix deadlock in
rtw_surveydone_event_callback()") besides fixing the deadlock also
modified rtw_scan_timeout_handler() to use spin_[un]lock_irq()
instead of spin_[un]lock_bh().
Disabling the IRQs is not necessary since all code taking this lock
runs from either user contexts or from softirqs
rtw_scan_timeout_handler() is the only function taking pmlmepriv->lock
which uses spin_[un]lock_irq() for this. Switch back to
spin_[un]lock_bh() to make it consistent with the rest of the code.
Fixes: cc7ad0d77b51 ("drivers: staging: rtl8723bs: Fix deadlock in rtw_surveydone_event_callback()") Cc: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230221145326.7808-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 041879b12ddb ("drivers: staging: rtl8192bs: Fix deadlock in
rtw_joinbss_event_prehandle()") besides fixing the deadlock also
modified _rtw_join_timeout_handler() to use spin_[un]lock_irq()
instead of spin_[un]lock_bh().
_rtw_join_timeout_handler() calls rtw_do_join() which takes
pmlmepriv->scanned_queue.lock using spin_[un]lock_bh(). This
spin_unlock_bh() call re-enables softirqs which triggers an oops in
kernel/softirq.c: __local_bh_enable_ip() when it calls
lockdep_assert_irqs_enabled():
This oops is causd by the switch to spin_[un]lock_irq() which disables
the IRQs for the entire duration of _rtw_join_timeout_handler().
Disabling the IRQs is not necessary since all code taking this lock
runs from either user contexts or from softirqs, switch back to
spin_[un]lock_bh() to fix this.
Fixes: 041879b12ddb ("drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()") Cc: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230221145326.7808-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In error situations, only the internal boost case should be disabled and
re-enabled.
Also, for other boost cases re-enabling the boost to the default internal
boost config is incorrect.
Fixes: 6450ef559056 ("ASoC: cs35l41: CS35L41 Boosted Smart Amplifier") Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: David Rhodes <david.rhodes@cirrus.com> Link: https://lore.kernel.org/r/20230223084324.9076-2-lucas.tanure@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP_MMIO" to
"select REGMAP_MMIO", which will also set REGMAP.
Fixes: eb994594bc22 ("ipmi: bt-bmc: Use a regmap for register access") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Andrew Jeffery <andrew@aj.id.au> Cc: Corey Minyard <minyard@acm.org> Cc: openipmi-developer@lists.sourceforge.net Cc: Arnd Bergmann <arnd@arndb.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <20230226053953.4681-2-rdunlap@infradead.org> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sendmsg() calls msg_zerocopy_alloc(), which allocates a skb, sets
skb->cb->ubuf.refcnt to 1, and calls sock_hold(). Here, struct
ubuf_info_msgzc indirectly holds a refcnt of the socket. When the
skb is sent, __skb_tstamp_tx() clones it and puts the clone into
the socket's error queue with the TX timestamp.
When the original skb is received locally, skb_copy_ubufs() calls
skb_unclone(), and pskb_expand_head() increments skb->cb->ubuf.refcnt.
This additional count is decremented while freeing the skb, but struct
ubuf_info_msgzc still has a refcnt, so __msg_zerocopy_callback() is
not called.
The last refcnt is not released unless we retrieve the TX timestamped
skb by recvmsg(). Since we clear the error queue in inet_sock_destruct()
after the socket's refcnt reaches 0, there is a circular dependency.
If we close() the socket holding such skbs, we never call sock_put()
and leak the count, sk, and skb.
TCP has the same problem, and commit e0c8bccd40fc ("net: stream:
purge sk_error_queue in sk_stream_kill_queues()") tried to fix it
by calling skb_queue_purge() during close(). However, there is a
small chance that skb queued in a qdisc or device could be put
into the error queue after the skb_queue_purge() call.
In __skb_tstamp_tx(), the cloned skb should not have a reference
to the ubuf to remove the circular dependency, but skb_clone() does
not call skb_copy_ubufs() for zerocopy skb. So, we need to call
skb_orphan_frags_rx() for the cloned skb to call skb_copy_ubufs().
After failing to verify configuration, it returns directly without
releasing link, which may cause memory leak.
Paolo Abeni thinks that the whole code of this driver is quite
"suboptimal" and looks unmainatained since at least ~15y, so he
suggests that we could simply remove the whole driver, please
take it into consideration.
Simon Horman suggests that the fix label should be set to
"Linux-2.6.12-rc2" considering that the problem has existed
since the driver was introduced and the commit above doesn't
seem to exist in net/net-next.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gan Gecen <gangecen@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Brad Spencer provided a detailed report [0] that when calling getsockopt()
for AF_NETLINK, some SOL_NETLINK options set only 1 byte even though such
options require at least sizeof(int) as length.
The options return a flag value that fits into 1 byte, but such behaviour
confuses users who do not initialise the variable before calling
getsockopt() and do not strictly check the returned value as char.
Currently, netlink_getsockopt() uses put_user() to copy data to optlen and
optval, but put_user() casts the data based on the pointer, char *optval.
As a result, only 1 byte is set to optval.
To avoid this behaviour, we need to use copy_to_user() or cast optval for
put_user().
Note that this changes the behaviour on big-endian systems, but we document
that the size of optval is int in the man page.
$ man 7 netlink
...
Socket options
To set or get a netlink socket option, call getsockopt(2) to read
or setsockopt(2) to write the option with the option level argument
set to SOL_NETLINK. Unless otherwise noted, optval is a pointer to
an int.
Fixes: 9a4595bc7e67 ("[NETLINK]: Add set/getsockopt options to support more than 32 groups") Fixes: be0c22a46cfb ("netlink: add NETLINK_BROADCAST_ERROR socket option") Fixes: 38938bfe3489 ("netlink: add NETLINK_NO_ENOBUFS socket flag") Fixes: 0a6a3a23ea6e ("netlink: add NETLINK_CAP_ACK socket option") Fixes: 2d4bc93368f5 ("netlink: extended ACK reporting") Fixes: 89d35528d17d ("netlink: Add new socket option to enable strict checking on dumps") Reported-by: Brad Spencer <bspencer@blackberry.com> Link: https://lore.kernel.org/netdev/ZD7VkNWFfp22kTDt@datsun.rim.net/ Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20230421185255.94606-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch introduces a possible null-ptr-def problem. Revert it. And the
fixed bug by this patch have resolved by commit 73f7b171b7c0 ("Bluetooth:
btsdio: fix use after free bug in btsdio_remove due to race condition").
Fixes: 1e9ac114c442 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When converting from ASSERTCMP to WARN_ON, the tested condition must
be inverted, which was missed for this case.
This would cause an EIO error when trying to read an rxrpc token, for
instance when trying to display tokens with AuriStor's "tokens" command.
Fixes: 84924aac08a4 ("rxrpc: Fix checker warning") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Like commit ea30388baebc ("ipv6: Fix an uninit variable access bug in
__ip6_make_skb()"). icmphdr does not in skb linear region under the
scenario of SOCK_RAW socket. Access icmp_hdr(skb)->type directly will
trigger the uninit variable access bug.
Use a local variable icmp_type to carry the correct value in different
scenarios.
Fixes: 96793b482540 ("[IPV4]: Add ICMPMsgStats MIB (RFC 4293)") Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
if sch_fq is configured with "initial quantum" having values greater than
INT_MAX, the first assignment of "credit" does signed integer overflow to
a very negative value.
In this situation, the syzkaller script provided by Cristoph triggers the
CPU soft-lockup warning even with few sockets. It's not an infinite loop,
but "credit" wasn't probably meant to be minus 2Gb for each new flow.
Capping "initial quantum" to INT_MAX proved to fix the issue.
v2: validation of "initial quantum" is done in fq_policy, instead of open
coding in fq_change() _ suggested by Jakub Kicinski
The return value is not initialized on the success path.
Fixes: 901bdff2f529 ("net: fman: Change return type of disable to void") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Link: https://lore.kernel.org/r/8c9dc377-8495-495f-a4e5-4d2d0ee12f0c@kili.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some socket options do getsockopt with optval=NULL to estimate the size
of the final buffer (which is returned via optlen). This breaks BPF
getsockopt assumptions about permitted optval buffer size. Let's enforce
these assumptions only when non-NULL optval is provided.
Florian and Eduard reported hard dead lock:
[ 58.433327] _raw_spin_lock_irqsave+0x40/0x50
[ 58.433334] btf_put+0x43/0x90
[ 58.433338] bpf_find_btf_id+0x157/0x240
[ 58.433353] btf_parse_fields+0x921/0x11c0
This happens since btf->refcount can be 1 at the time of btf_put() and
btf_put() will call btf_free_id() which will try to grab btf_idr_lock
and will dead lock.
Avoid the issue by doing btf_put() without locking.
Fixes: 3d78417b60fb ("bpf: Add bpf_btf_find_by_name_kind() helper.") Fixes: 1e89106da253 ("bpf: Add bpf_core_add_cands() and wire it into bpf_core_apply_relo_insn().") Reported-by: Florian Westphal <fw@strlen.de> Reported-by: Eduard Zingerman <eddyz87@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Eduard Zingerman <eddyz87@gmail.com> Link: https://lore.kernel.org/bpf/20230421014901.70908-1-alexei.starovoitov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The system hang because of dsa_tag_8021q_port_setup()->
stmmac_vlan_rx_add_vid().
I found in stmmac_drv_probe() that cailing pm_runtime_put()
disabled the clock.
First, when the kernel is compiled with CONFIG_PM=y,The stmmac's
resume/suspend is active.
Secondly,stmmac as DSA master,the dsa_tag_8021q_port_setup() function
will callback stmmac_vlan_rx_add_vid when DSA dirver starts. However,
The system is hanged for the stmmac_vlan_rx_add_vid() accesses its
registers after stmmac's clock is closed.
I would suggest adding the pm_runtime_resume_and_get() to the
stmmac_vlan_rx_add_vid().This guarantees that resuming clock output
while in use.
Fixes: b3dcb3127786 ("net: stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()") Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Yan Wang <rk.code@outlook.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The termination table usage is requires for DMFS steering mode as firmware
doesn't support mixed table destinations list which causes following
syndrome with hairpin rules:
[81922.283225] mlx5_core 0000:08:00.0: mlx5_cmd_out_err:803:(pid 25977): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xaca205), err(-22)
Fixes: 14624d7247fc ("net/mlx5e: Don't use termination table when redundant") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On failing to create promisc flow steering table, the pointer is
returned with an error. Nullify it so unloading the driver won't try to
destroy a non existing table.
Failing to create promisc table may happen over BF devices when the ARM
side is going through a firmware tear down. The host side start a
reload flow. While the driver unloads, it tries to remove the promisc
table. Remove WARN in this state as it is a valid error flow.
Use the same timeout for sync reset flow and health recovery flow, since
the former involves driver's recovery from firmware reset, which is
similar to health recovery. Otherwise, in some cases, such as a firmware
upgrade on the DPU, the firmware pre-init bit may not be ready within
current timeout and the driver will abort loading back after reset.
Revert this patch as we need the "recovery" arg back in mlx5_load_one()
function. This arg will be used in the next patch for using recovery
timeout during sync reset flow.
The original behavior introduced by commit c6acd629eec7 ("net/mlx5e: Add
support for devlink-port in non-representors mode") correctly
re-instantiated uplink devlink port and related netdevice during devlink
reload. However with migration to auxiliary devices, this behaviour
changed.
Restore the original behaviour and tear down auxiliary devices
completely during devlink reload.
On representor init rx error flow the flow steering pointer is being
released so mlx5e_attach_netdev() doesn't have a valid fs pointer
in its error flow. Make sure the pointer is nullified when released
and add a check in mlx5e_fs_cleanup() to verify fs is not null
as representor cleanup callback would be called anyway.
Fixes: af8bbf730068 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Source port rewrite (forward to ovs internal port or statck device) isn't
supported in the rule of split action. So there is no indirect table in
split rule. The cited commit destroyes indirect table in split rule. The
indirect table for other rules will be destroyed wrongly. It will cause
traffic loss.
Fix it by removing the destroy function in split rule. And also remove
the destroy function in error flow.
Fixes: 10742efc20a4 ("net/mlx5e: VF tunnel TX traffic offloading") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when creating per vport table, create flags are hardcoded.
Devlink encap mode is set based on user input and HW capability.
Create per vport table based on devlink encap mode.
Fixes: c796bb7cd230 ("net/mlx5: E-switch, Generalize per vport table API") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code already clones post action attributes in
mlx5e_clone_flow_attr_for_post_act(). Creating another copy in
mlx5e_tc_post_act_add() is a erroneous leftover from original
implementation. Instead, assign handle->attribute to post_attr provided by
the caller. Note that cloning the attribute second time is not just
wasteful but also causes issues like second copy not being properly updated
in neigh update code which leads to following use-after-free:
Feb 21 09:02:00 c-237-177-40-045 kernel: BUG: KASAN: use-after-free in mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_report+0xbb/0x1a0
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: __kasan_kmalloc+0x7a/0x90
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_free_info+0x2a/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: ____kasan_slab_free+0x11a/0x1b0
Feb 21 09:02:00 c-237-177-40-045 kernel: page dumped because: kasan: bad access detected
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0: mlx5_cmd_out_err:803:(pid 8833): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0xf2ff71), err(-22)
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0 enp8s0f0: Failed to add post action rule
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0: mlx5e_tc_encap_flows_add:190:(pid 8833): Failed to update flow post acts, -22
Feb 21 09:02:00 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:02:00 c-237-177-40-045 kernel: <TASK>
Feb 21 09:02:00 c-237-177-40-045 kernel: dump_stack_lvl+0x57/0x7d
Feb 21 09:02:00 c-237-177-40-045 kernel: print_report+0x170/0x471
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_report+0xbb/0x1a0
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: ? __module_address.part.0+0x62/0x200
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_stub_create_flow_table+0xd0/0xd0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: ? __raw_spin_lock_init+0x3b/0x110
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_cmd_create_fte+0x80/0xb0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: add_rule_fg+0xe80/0x19c0 [mlx5_core]
--
Feb 21 09:02:00 c-237-177-40-045 kernel: Allocated by task 13476:
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: __kasan_kmalloc+0x7a/0x90
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_packet_reformat_alloc+0x7b/0x230 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_tun_create_header_ipv4+0x977/0xf10 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_attach_encap+0x15b4/0x1e10 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: post_process_attr+0x305/0xa30 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_add_fdb_flow+0x4c0/0xcf0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: __mlx5e_add_fdb_flow+0x7cf/0xe90 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_configure_flower+0xcaa/0x4b90 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_setup_tc_cls_flower+0x99/0x1b0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_setup_tc_cb+0x133/0x1e0 [mlx5_core]
--
Feb 21 09:02:00 c-237-177-40-045 kernel: Freed by task 8833:
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_free_info+0x2a/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: ____kasan_slab_free+0x11a/0x1b0
Feb 21 09:02:00 c-237-177-40-045 kernel: __kmem_cache_free+0x1de/0x400
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_packet_reformat_dealloc+0xad/0x100 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_encap_flows_del+0x3c0/0x500 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_update_flows+0x40c/0xa80 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_neigh_update+0x473/0x7a0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:02:00 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:02:00 c-237-177-40-045 kernel: kthread+0x28f/0x330
Fixes: 8300f225268b ("net/mlx5e: Create new flow attr for multi table actions") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ethtool uses `ETHTOOL_GRXRINGS` to compute how many queues are supported
by RSS. The driver should return the smaller of either:
- The maximum number of RSS queues the device supports, OR
- The number of RX queues configured
Prior to this change, running `ethtool -X $iface default` fails if the
number of queues configured is larger than the number supported by RSS,
even though changing the queue count correctly resets the flowhash to
use all supported queues.
Other drivers (for example, i40e) will succeed but the flow hash will
reset to support the maximum number of queues supported by RSS, even if
that amount is smaller than the configured amount.
After this change, the flowhash can be reset to default which will use
all of the available RSS queues (16) or the configured queue count,
whichever is smaller.
Starting with eth1 which has 10 queues and a flowhash distributing to
all 10 queues:
ixgbe currently returns `EINVAL` whenever the flowhash it set by ethtool
because the ethtool code in the kernel passes a non-zero value for hfunc
that ixgbe should allow.
When ethtool is called with `ETHTOOL_SRXFHINDIR`,
`ethtool_set_rxfh_indir` will call ixgbe's set_rxfh function
with `ETH_RSS_HASH_NO_CHANGE`. This value should be accepted.
When ethtool is called with `ETHTOOL_SRSSH`, `ethtool_set_rxfh` will
call ixgbe's set_rxfh function with `rxfh.hfunc`, which appears to be
hardcoded in ixgbe to always be `ETH_RSS_HASH_TOP`. This value should
also be accepted.
Fix a memory leak that occurs when reading the fw_info
file all the way, since we return NULL indicating no
more data, but don't free the status tracking object.
(struct nf_conn)->timeout is an interval before the conntrack
confirmed. After confirmed, it becomes a timestamp.
It is observed that timeout of an unconfirmed conntrack:
- Set by calling ctnetlink_change_timeout(). As a result,
`nfct_time_stamp` was wrongly added to `ct->timeout` twice.
- Get by calling ctnetlink_dump_timeout(). As a result,
`nfct_time_stamp` was wrongly subtracted.
Separate the 2 cases in:
- Setting `ct->timeout` in __nf_ct_set_timeout().
- Getting `ct->timeout` in ctnetlink_dump_timeout().
Pablo appends:
Update ctnetlink to set up the timeout _after_ the IPS_CONFIRMED flag is
set on, otherwise conntrack creation via ctnetlink breaks.
Note that the problem described in this patch occurs since the
introduction of the nfnetlink_queue conntrack support, select a
sufficiently old Fixes: tag for -stable kernel to pick up this fix.
Fixes: a4b4766c3ceb ("netfilter: nfnetlink_queue: rename related to nfqueue attaching conntrack info") Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
e6d57e9ff0ae ("netfilter: conntrack: fix rmmod double-free race")
consolidates IPS_CONFIRMED bit set in nf_conntrack_hash_check_insert().
However, this breaks ctnetlink:
If the chip reset worker is triggered during the remove process, the chip
DMA may not be properly pushed back to the idle state. This can lead to
corruption of the DMA flow due to the chip reset. Therefore, it is
necessary to stop the chip reset before the DMA is finalized.
To avoid resetting the chip after the reset worker is cancelled, use
__mt7921_mcu_drv_pmctrl() instead of mt7921_mcu_drv_pmctrl(). It is safe to
ignore the pm mutex because the pm worker and wake worker have already been
cancelled.
Fixes: 033ae79b3830 ("mt76: mt7921: refactor init.c to be bus independent") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Co-developed-by: Wang Zhao <wang.zhao@mediatek.com> Signed-off-by: Wang Zhao <wang.zhao@mediatek.com> Signed-off-by: Quan Zhou <quan.zhou@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
