The two GPIO quirk bits only affected actual GPIO selection
when set by the quirks table. They were reported as being
in effect when set via module options but actually did nothing.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andrey Turkin <andrey.turkin@gmail.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220725194909.145418-4-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, almost all archs (x86, arm64, mips...) support fast call
of crash_kexec() when "regs && kexec_should_crash()" is true. But
RISC-V not, it can only enter crash system via panic(). However panic()
doesn't pass the regs of the real accident scene to crash_kexec(),
it caused we can't get accurate backtrace via gdb,
$ riscv64-linux-gnu-gdb vmlinux vmcore
Reading symbols from vmlinux...
[New LWP 95]
#0 console_unlock () at kernel/printk/printk.c:2557
2557 if (do_cond_resched)
(gdb) bt
#0 console_unlock () at kernel/printk/printk.c:2557
#1 0x0000000000000000 in ?? ()
With the patch we can get the accurate backtrace,
$ riscv64-linux-gnu-gdb vmlinux vmcore
Reading symbols from vmlinux...
[New LWP 95]
#0 0xffffffe00063a4e0 in test_thread (data=<optimized out>) at drivers/test_crash.c:81
81 *(int *)p = 0xdead;
(gdb)
(gdb) bt
#0 0xffffffe00064d5c0 in test_thread (data=<optimized out>) at drivers/test_crash.c:81
#1 0x0000000000000000 in ?? ()
Test code to produce NULL address dereference in test_crash.c,
void *p = NULL;
*(int *)p = 0xdead;
As mentioned in Table 4.5 in RISC-V spec Volume 2 Section 4.3, write
but not read is "Reserved for future use.". For now, they are not valid.
In the current code, -wx is marked as invalid, but -w- is not marked
as invalid.
This patch refines that judgment.
Reported-by: xctan <xc-tan@outlook.com> Co-developed-by: dram <dramforever@live.com> Signed-off-by: dram <dramforever@live.com> Co-developed-by: Ruizhe Pan <c141028@gmail.com> Signed-off-by: Ruizhe Pan <c141028@gmail.com> Signed-off-by: Celeste Liu <coelacanthus@outlook.com> Link: https://lore.kernel.org/r/PH7PR14MB559464DBDD310E755F5B21E8CEDC9@PH7PR14MB5594.namprd14.prod.outlook.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The remove() operation unconditionally frees the interrupt for the device
but we may not actually have an interrupt so there might be nothing to
free. Since the interrupt is requested after all other resources we don't
need the explicit free anyway, unwinding is guaranteed to be safe, so just
delete the remove() function and let devm take care of things.
Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Tested-by: Zheyu Ma <zheyuma97@gmail.com> Link: https://lore.kernel.org/r/20220718140405.57233-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before, ssiu.c didn't care SSI5-8, thus,
commit b1384d4c95088d0 ("ASoC: rsnd: care default case on
rsnd_ssiu_busif_err_status_clear()") cares it for status clear.
But we should care it for error irq handling, too.
This patch cares it.
Reported-by: Nguyen Bao Nguyen <nguyen.nguyen.yj@renesas.com> Reported-by: Nishiyama Kunihiko <kunihiko.nishiyama.dn@renesas.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/871quocio1.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not yet clear, but it is possible to create a firmware so broken
that it will send a reply message before a FW_READY message (it is not
yet clear if FW_READY will arrive later).
Since the reply_data is allocated only after the FW_READY message, this
will lead to a NULL pointer dereference if not filtered out.
The issue was reported with IPC4 firmware but the same condition is present
for IPC3.
Reported-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220712122357.31282-3-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not yet clear, but it is possible to create a firmware so broken
that it will send a reply message before a FW_READY message (it is not
yet clear if FW_READY will arrive later).
Since the reply_data is allocated only after the FW_READY message, this
will lead to a NULL pointer dereference if not filtered out.
The issue was reported with IPC4 firmware but the same condition is present
for IPC3.
Reported-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220712122357.31282-2-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the kernel image vmlinux.lds.S linker scripts the .altinstructions
and __bug_table sections are 4- or 8-byte aligned because they hold 32-
and/or 64-bit values.
Most architectures use altinstructions and BUG() or WARN() in modules as
well, but in the module linker script (module.lds.S) those sections are
currently missing. As consequence the linker will store their content
byte-aligned by default, which then can lead to unnecessary unaligned
memory accesses by the CPU when those tables are processed at runtime.
Usually unaligned memory accesses are unnoticed, because either the
hardware (as on x86 CPUs) or in-kernel exception handlers (e.g. on
parisc or sparc) emulate and fix them up at runtime. Nevertheless, such
unaligned accesses introduce a performance penalty and can even crash
the kernel if there is a bug in the unalignment exception handlers
(which happened once to me on the parisc architecture and which is why I
noticed that issue at all).
This patch fixes a non-critical issue and might be backported at any time.
It's trivial and shouldn't introduce any regression because it simply
tells the linker to use a different (8-byte alignment) for those
sections by default.
If early probe of HDAudio bus driver fails e.g.: due to missing
firmware file, snd_hda_codec_shutdown() ends in manipulating
uninitialized codec->pcm_list_head causing page fault.
Iinitialization of HDAudio codec in ASoC is split in two:
- snd_hda_codec_device_init()
- snd_hda_codec_device_new()
snd_hda_codec_device_init() is called during probe_codecs() by HDAudio
bus driver while snd_hda_codec_device_new() is called by
codec-component's ->probe(). The second call will not happen until all
components required by related sound card are present within the ASoC
framework. With firmware failing to load during the PCI's deferred
initialization i.e.: probe_work(), no platform components are ever
registered. HDAudio codec enumeration is done at that point though, so
the codec components became registered to ASoC framework, calling
snd_hda_codec_device_init() in the process.
Now, during platform reboot snd_hda_codec_shutdown() is called for every
codec found on the HDAudio bus causing oops if any of them has not
completed both of their initialization steps. Relocating field
initialization fixes the issue.
Apparently it is possible for code to allocate large buffers which may
cause warnings as reported in [1]. This was fixed for HDA, SOF and
skylake in patchset [2], fix it also for avs driver.
We should call of_node_put() for the reference 'uctl_node' returned by
of_get_parent() which will increase the refcount. Otherwise, there will
be a refcount leak bug.
Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
On buffer resize failure, vfio_info_cap_add() will free the buffer,
report zero for the size, and return -ENOMEM. As additional
hardening, also clear the buffer pointer to prevent any chance of a
double free.
Signed-off-by: Schspa Shi <schspa@gmail.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Link: https://lore.kernel.org/r/20220629022948.55608-1-schspa@gmail.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "rm_exit" is always showing zero because it is the last one and
end_timing does not increment the counter of the previous entry.
We can fix it by calling accumulate_time again instead of
end_timing. That way the counter gets incremented. The rest of the
arithmetic can be ignored because there are no timing points after
this and the accumulators are reset before the next round.
In some circumstances, attempts are made to add entries to or to remove
entries from an uninitialized list. A prime example is
amdgpu_bo_vm_destroy(): It is indirectly called from
ttm_bo_init_reserved() if that function fails, and tries to remove an
entry from a list. However, that list is only initialized in
amdgpu_bo_create_vm() after the call to ttm_bo_init_reserved() returned
success. This results in crashes such as
This patch avoids an attempt to resize the filesystem to an
unaligned cluster boundary. An online resize to a size that is not
integral to cluster size results in the last iteration attempting to
grow the fs by a negative amount, which trips a BUG_ON and leaves the fs
with a corrupted in-memory superblock.
Block range to free is validated in ext4_free_blocks() using
ext4_inode_block_valid() and then it's passed to ext4_mb_clear_bb().
However in some situations on bigalloc file system the range might be
adjusted after the validation in ext4_free_blocks() which can lead to
troubles on corrupted file systems such as one found by syzkaller that
resulted in the following BUG
Now if check directoy entry is corrupted, ext4_empty_dir may return true
then directory will be removed when file system mounted with "errors=continue".
In order not to make things worse just return false when directory is corrupted.
In line 2884, "raid5_release_stripe(sh);" drops the reference to sh and
may cause sh to be released. However, sh is subsequently used in lines
2886 "if (sh->batch_head && sh != sh->batch_head)". This may result in an
use-after-free bug.
It can be fixed by moving "raid5_release_stripe(sh);" to the bottom of
the function.
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We probably need nvmet_tcp_wq to have MEM_RECLAIM as we are
sending/receiving for the socket from works on this workqueue.
Also this eliminates lockdep complaints:
--
[ 6174.010200] workqueue: WQ_MEM_RECLAIM
nvmet-wq:nvmet_tcp_release_queue_work [nvmet_tcp] is flushing
!WQ_MEM_RECLAIM nvmet_tcp_wq:nvmet_tcp_io_work [nvmet_tcp]
[ 6174.010216] WARNING: CPU: 20 PID: 14456 at kernel/workqueue.c:2628
check_flush_dependency+0x110/0x14c
Reported-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The check in raid5_make_request differs very slightly from the logic
that causes it to block lower down. This likely does not cause a bug
as the check is fuzzy anyway (as reshape may move on between the first
check and the subsequent check). However, make it consistent so it can
be cleaned up in a subsequent patch.
The mdadm test 07layouts randomly produces a kernel hung task deadlock.
The deadlock is caused by the suspend_lo/suspend_hi files being set by
the mdadm background process during reshape and not being cleared
because the process hangs. (Leaving aside the issue of the fragility of
freezing kernel tasks by buggy userspace processes...)
When the background mdadm process hangs it, is waiting (without a
timeout) on a change to the sync_completed file signalling that the
reshape has completed. The process is woken up a couple times when
the reshape finishes but it is woken up before MD_RECOVERY_RUNNING
is cleared so sync_completed_show() reports 0 instead of "none".
To fix this, notify the sysfs file in md_reap_sync_thread() after
MD_RECOVERY_RUNNING has been cleared. This wakes up mdadm and causes
it to continue and write to suspend_lo/suspend_hi to allow IO to
continue.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The exynos-pcie driver called phy_power_on() before phy_init() for some
historical reasons. However the generic PHY framework assumes that the
proper sequence is to call phy_init() first, then phy_power_on(). The
operations done by both functions should be considered as one action and as
such they are called by the exynos-pcie driver (without doing anything
between them). The initialization is just a sequence of register writes,
which cannot be altered without breaking the hardware operation.
To match the generic PHY framework requirement, simply move all register
writes to the phy_init()/phy_exit() and drop power_on()/power_off()
callbacks. This way the driver will also work with the old (incorrect)
PHY initialization call sequence.
Link: https://lore.kernel.org/r/20220628220409.26545-1-m.szyprowski@samsung.com Reported-by: Bjorn Helgaas <helgaas@kernel.org> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Chanho Park <chanho61.park@samsung.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-By: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When OpenRISC enables PCI it allows for more drivers to be compiled
resulting in exposing the following with -Werror.
drivers/video/fbdev/riva/fbdev.c: In function 'rivafb_probe':
drivers/video/fbdev/riva/fbdev.c:2062:42: error:
passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type
drivers/video/fbdev/nvidia/nvidia.c: In function 'nvidiafb_probe':
drivers/video/fbdev/nvidia/nvidia.c:1414:20: error:
passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type
drivers/scsi/aic7xxx/aic7xxx_osm.c: In function 'ahc_platform_free':
drivers/scsi/aic7xxx/aic7xxx_osm.c:1231:41: error:
passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type
Most architectures define the iounmap argument to be volatile. To fix this
issue we do the same for OpenRISC. This patch must go before PCI is enabled on
OpenRISC to avoid any compile failures.
Below 2 commits will be reverted:
commit 8ff5f5d9d8cf ("RDMA/rxe: Prevent double freeing rxe_map_set()")
commit 647bf13ce944 ("RDMA/rxe: Create duplicate mapping tables for FMRs")
The community has a few bug reports which pointed this commit at last.
Some proposals are raised up in the meantime but all of them have no
follow-up operation.
The previous commit led the map_set of FMR to be not available any more if
the MR is registered again after invalidating. Although the mentioned
patch try to fix a potential race in building/accessing the same table
for fast memory regions, it broke rtrs etc ULPs. Since the latter could
be worse, revert this patch.
With previous commit, it's observed that a same MR in rnbd server will
trigger below code path:
-> rxe_mr_init_fast()
|-> alloc map_set() # map_set is uninitialized
|...-> rxe_map_mr_sg() # build the map_set
|-> rxe_mr_set_page()
|...-> rxe_reg_fast_mr() # mr->state change to VALID from FREE that means
# we can access host memory(such rxe_mr_copy)
|...-> rxe_invalidate_mr() # mr->state change to FREE from VALID
|...-> rxe_reg_fast_mr() # mr->state change to VALID from FREE,
# but map_set was not built again
|...-> rxe_mr_copy() # kernel crash due to access wild addresses
# that lookup from the map_set
It's not allowed to quit remove early without cleaning up completely.
Otherwise this results in resource leaks that probably yield graver
problems later. Here for example some tasklets might survive the lifetime
of the sprd-dma device and access sdev which is freed after .remove()
returns.
As none of the device freeing requires an active device, just ignore the
return value of pm_runtime_get_sync().
In certain cases where the DMA client bus gets corrupted or if the
end device ceases to send/receive data, DMA can wait indefinitely
for the data to be received/sent. Attempting to terminate the transfer
will put the DMA in pause flush mode and it remains there.
The channel is irrecoverable once this pause times out in Tegra194 and
earlier chips. Whereas, from Tegra234, it can be recovered by disabling
the channel and reprograming it.
Hence add a new terminate() function that ignores the outcome of
dma_pause() so that terminate_all() can proceed to disable the channel.
A new feature is added where kprobes (and other probes) do not need to
explicitly state the event name when creating a probe. The event name will
come from what is being attached.
That is:
# echo 'p:foo/ vfs_read' > kprobe_events
Will no longer error, but instead create an event:
# cat kprobe_events
p:foo/p_vfs_read_0 vfs_read
This should not be tested as an error case anymore. Remove it from the
selftest as now this feature "breaks" the selftest as it no longer fails
as expected.
On kprobe registration kernel allocate one insn_slot for new kprobe,
but it forget to reclaim the insn_slot on unregistration, leading to a
potential leakage.
Limit the maximum number of calls to each tasklet from rxe_do_task()
before yielding the cpu. When the limit is reached reschedule the tasklet
and exit the calling loop. This patch prevents one tasklet from consuming
100% of a cpu core and causing a deadlock or soft lockup.
Currently, everytime an information needs to be fetched from the PPTT,
the table is mapped via acpi_get_table() and unmapped after the use via
acpi_put_table() which is fine. However we do this at runtime especially
when the CPU is hotplugged out and plugged in back since we re-populate
the cache topology and other information.
However, with the support to fetch LLC information from the PPTT in the
cpuhotplug path which is executed in the atomic context, it is preferred
to avoid mapping and unmapping of the PPTT for every single use as the
acpi_get_table() might sleep waiting for a mutex.
In order to avoid the same, the table is needs to just mapped once on
the boot CPU and is never unmapped allowing it to be used at runtime
with out the hassle of mapping and unmapping the table.
Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
--
Hi Rafael,
Sorry to bother you again on this PPTT changes. Guenter reported an issue
with lockdep enabled in -next that include my cacheinfo/arch_topology changes
to utilise LLC from PPTT in the CPU hotplug path.
Please ack the change once you are happy so that I can get it merged with
other fixes via Greg's tree.
The newest Gen3 SoCs and Gen4 SoCs do not need manual tap correction
with HS400 anymore. So, instead of checking the SDHI version, add a
quirk flag and set manual tap correction only for affected SoCs.
If the channel has no descriptor and the interrupt is raised then the
kernel will OOPS. Check the result of vchan_next_desc() in the handler
axi_chan_block_xfer_complete() to avoid the error happening.
During debugging we have seen an issue where axi_chan_dump_lli()
is passed a NULL LLI pointer which ends up causing an OOPS due
to trying to get fields from it. Simply print NULL LLI and exit
to avoid this.
There is no point in doing several preparatory steps in
of_overlay_fdt_apply(), only to see of_overlay_apply() return early
because of a corrupt device tree.
Move the check for a corrupt device tree from of_overlay_apply() to
of_overlay_fdt_apply(), to check for this as early as possible.
QEMU has a -no-reboot option, which halts instead of reboots when the
guest asks to reboot. This is invaluable when used with
CONFIG_PANIC_TIMEOUT=-1 (and panic_on_warn), because it allows panics
and warnings to be caught immediately in CI. Implement this in UML too,
by way of a basic setup param.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some cases we may get a platform device that has ACPI companion
which is different to the pin control described in the ACPI tables.
This is primarily happens when device is instantiated by board file.
In order to allow this device being enumerated, refactor
intel_pinctrl_get_soc_data() to check the matching data instead of
ACPI companion.
Reported-by: Henning Schild <henning.schild@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 1599069a62c6 ("phy: core: Warn when phy_power_on is called
before phy_init"), the following warning has been reported:
phy_power_on was called before phy_init
To address this, we need to remove phy_power_on from exynos_ufs_phy_init()
and move it after phy_init. phy_power_off and phy_exit are also necessary
in exynos_ufs_remove().
Link: https://lore.kernel.org/r/20220706020255.151177-4-chanho61.park@samsung.com Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to prepare the driver code for device reset event
notification, change the event handler function flow to call
device reset from one code block.
In addition, the commit fixes an issue that reset was performed
w/o checking the 'hard_reset_on_fw_event' state and w/o setting
the HL_DRV_RESET_DELAY flag.
Arrays of struct attribute are expected to be NULL terminated.
This is required by API methods such as device_add_groups.
This fixes a crash when loading the driver for Goya device.
When the following configs are enabled:
* CORESIGHT
* CORESIGHT_SOURCE_ETM4X
* UBSAN
* UBSAN_TRAP
Clang fails assemble the kernel with the error:
<instantiation>:1:7: error: expected constant expression in '.inst' directive
.inst (0xd5200000|((((2) << 19) | ((1) << 16) | (((((((((((0x160 + (i * 4))))) >> 2))) >> 7) & 0x7)) << 12) | ((((((((((0x160 + (i * 4))))) >> 2))) & 0xf)) << 8) | (((((((((((0x160 + (i * 4))))) >> 2))) >> 4) & 0x7)) << 5)))|(.L__reg_num_x8))
^
drivers/hwtracing/coresight/coresight-etm4x-core.c:702:4: note: while in
macro instantiation
etm4x_relaxed_read32(csa, TRCCNTVRn(i));
^
drivers/hwtracing/coresight/coresight-etm4x.h:403:4: note: expanded from
macro 'etm4x_relaxed_read32'
read_etm4x_sysreg_offset((offset), false)))
^
drivers/hwtracing/coresight/coresight-etm4x.h:383:12: note: expanded
from macro 'read_etm4x_sysreg_offset'
__val = read_etm4x_sysreg_const_offset((offset)); \
^
drivers/hwtracing/coresight/coresight-etm4x.h:149:2: note: expanded from
macro 'read_etm4x_sysreg_const_offset'
READ_ETM4x_REG(ETM4x_OFFSET_TO_REG(offset))
^
drivers/hwtracing/coresight/coresight-etm4x.h:144:2: note: expanded from
macro 'READ_ETM4x_REG'
read_sysreg_s(ETM4x_REG_NUM_TO_SYSREG((reg)))
^
arch/arm64/include/asm/sysreg.h:1108:15: note: expanded from macro
'read_sysreg_s'
asm volatile(__mrs_s("%0", r) : "=r" (__val)); \
^
arch/arm64/include/asm/sysreg.h:1074:2: note: expanded from macro '__mrs_s'
" mrs_s " v ", " __stringify(r) "\n" \
^
Consider the definitions of TRCSSCSRn and TRCCNTVRn:
drivers/hwtracing/coresight/coresight-etm4x.h:56
#define TRCCNTVRn(n) (0x160 + (n * 4))
drivers/hwtracing/coresight/coresight-etm4x.h:81
#define TRCSSCSRn(n) (0x2A0 + (n * 4))
Where the macro parameter is expanded to i; a loop induction variable
from etm4_disable_hw.
When any compiler can determine that loops may be unrolled, then the
__builtin_constant_p check in read_etm4x_sysreg_offset() defined in
drivers/hwtracing/coresight/coresight-etm4x.h may evaluate to true. This
can lead to the expression `(0x160 + (i * 4))` being passed to
read_etm4x_sysreg_const_offset. Via the trace above, this is passed
through READ_ETM4x_REG, read_sysreg_s, and finally to __mrs_s where it
is string-ified and used directly in inline asm.
Regardless of which compiler or compiler options determine whether a
loop can or can't be unrolled, which determines whether
__builtin_constant_p evaluates to true when passed an expression using a
loop induction variable, it is NEVER safe to allow the preprocessor to
construct inline asm like:
asm volatile (".inst (0x160 + (i * 4))" : "=r"(__val));
^ expected constant expression
Instead of read_etm4x_sysreg_offset() using __builtin_constant_p(), use
__is_constexpr from include/linux/const.h instead to ensure only
expressions that are valid integer constant expressions get passed
through to read_sysreg_s().
This is not a bug in clang; it's a potentially unsafe use of the macro
arguments in read_etm4x_sysreg_offset dependent on __builtin_constant_p.
There is no corresponding free routine if lpfc_sli4_issue_wqe fails to
issue the CMF WQE in lpfc_issue_cmf_sync_wqe.
If ret_val is non-zero, then free the iocbq request structure.
Link: https://lore.kernel.org/r/20220701211425.2708-6-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Malformed user input to debugfs results in buffer overflow crashes. Adapt
input string lengths to fit within internal buffers, leaving space for NULL
terminators.
Link: https://lore.kernel.org/r/20220701211425.2708-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After merging lucid and trion pll functions in commit 0b01489475c6
("clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid")
the function clk_trion_pll_configure() is left with an old description
header, which results in a W=2 compile time warning, fix it.
Always use crypto_has_comp() so that crypto can lookup module, call
usermodhelper to load the modules, wait for usermodhelper to finish and so
on. Otherwise crypto will do all of these steps under CPU hot-plug lock
and this looks like too much stuff to handle under the CPU hot-plug lock.
Besides this can end up in a deadlock when usermodhelper triggers a code
path that attempts to lock the CPU hot-plug lock, that zram already holds.
An example of such deadlock:
- path A. zram grabs CPU hot-plug lock, execs /sbin/modprobe from crypto
and waits for modprobe to finish
- path B. async work kthread that brings in scsi device. It wants to
register CPUHP states at some point, and it needs the CPU hot-plug
lock for that, which is owned by zram.
The uacce driver must deal with a possible removal of the parent device
or parent driver module rmmod at any time.
Although uacce_remove(), called on device removal and on driver unbind,
prevents future use of the uacce fops by removing the cdev, fops that
were called before that point may still be running.
Serialize uacce_fops_open() and uacce_remove() with uacce->mutex.
Serialize other fops against uacce_remove() with q->mutex.
Since we need to protect uacce_fops_poll() which gets called on the fast
path, replace uacce->queues_lock with q->mutex to improve scalability.
The other fops are only used during setup.
uacce_queue_is_valid(), checked under q->mutex or uacce->mutex, denotes
whether uacce_remove() has disabled all queues. If that is the case,
don't go any further since the parent device is being removed and
uacce->ops should not be called anymore.
When using usb-role-switch, D+ pull-up is set as soon as DTCL_SFTDISCON is
cleared, whatever the vbus valid signal state is. The pull-up should not
be set when vbus isn't present (this is determined by the drd controller).
This patch ensures that B-Session (so Peripheral role + vbus valid signal)
is valid before clearing the DCTL_SFTDISCON bit when role switch is used.
Keep original behavior when usb-role-switch isn't used.
If qla4xxx doesn't remove the connection before the session, the iSCSI
class tries to remove the connection for it. We were doing a
iscsi_put_conn() in the iter function which is not needed and will result
in a use after free because iscsi_remove_conn() will free the connection.
Link: https://lore.kernel.org/r/20220616222738.5722-2-michael.christie@oracle.com Tested-by: Nilesh Javali <njavali@marvell.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In usbhs_rza1_hardware_init(), of_find_node_by_name() will return
a node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
In ohci_hcd_ppc_of_probe(), of_find_compatible_node() will return
a node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220617034637.4003115-1-windhl@126.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some drivers that can use the Type C mux API, but don't have
to. Introduce CONFIG guards for the mux functions so that drivers can
include the header file and not run into compilation errors on systems
which don't have CONFIG_TYPEC enabled. When CONFIG_TYPEC is not enabled,
the Type C mux functions will be stub versions of the original calls.
Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Prashant Malani <pmalani@chromium.org> Link: https://lore.kernel.org/r/20220615172129.1314056-3-pmalani@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the LPM configurations of device regulators may not work since
VCC is not disabled yet while ufs_mtk_vreg_set_lpm() is executed.
Fix this by changing the timing of invoking ufs_mtk_vreg_set_lpm().
Link: https://lore.kernel.org/r/20220616053725.5681-5-stanley.chu@mediatek.com Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the addition of clock-output-names, we can now unify the internal
clock naming for omap4 and 5 to follow the other TI SoCs.
We are still using legacy clkctrl names for omap4 and 5 based on the clock
manager name which is wrong. Instead, we want to use the clkctrl clock
based naming.
We must now also drop the legacy TI_CLK_CLKCTRL_COMPAT quirk for the
clkctrl clock.
This change will allow further devicetree warning cleanup as already
done for am3/4 and dra7.
Cc: linux-clk@vger.kernel.org Cc: Stephen Boyd <sboyd@kernel.org> Cc: Tero Kristo <kristo@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20220615064306.22254-1-tony@atomide.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix -Woverflow warnings for drm/meson driver which is a result
of moving arm64 custom MMIO accessor macros to asm-generic function
implementations giving a bonus type-checking now and uncovering these
overflow warnings.
drivers/gpu/drm/meson/meson_viu.c: In function ‘meson_viu_init’:
drivers/gpu/drm/meson/meson_registers.h:1826:48: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define VIU_OSD_BLEND_REORDER(dest, src) ((src) << (dest * 4))
^
drivers/gpu/drm/meson/meson_viu.c:472:18: note: in expansion of macro ‘VIU_OSD_BLEND_REORDER’
writel_relaxed(VIU_OSD_BLEND_REORDER(0, 1) |
^~~~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix -Woverflow warnings for tegra irqchip driver which is a result
of moving arm64 custom MMIO accessor macros to asm-generic function
implementations giving a bonus type-checking now and uncovering these
overflow warnings.
drivers/irqchip/irq-tegra.c: In function ‘tegra_ictlr_suspend’:
drivers/irqchip/irq-tegra.c:151:18: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel_relaxed(~0ul, ictlr + ICTLR_COP_IER_CLR);
^
Suggested-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Cc: Marc Zyngier <maz@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Slot capabilities are currently not reported because emulated bridge does
not report the PCI_EXP_FLAGS_SLOT flag.
Set PCI_EXP_FLAGS_SLOT to let the kernel know that PCI_EXP_SLT* registers
are supported.
Move setting of PCI_EXP_SLTCTL register from "dynamic" pcie_conf_read
function to static buffer as it is only statically filled the
PCI_EXP_SLTSTA_PDS flag and dynamic read callback is not needed for this
register.
Set Presence State Bit to 1 since there is no support for unplugging the
card and there is currently no platform able to detect presence of a card -
in such a case the bit needs to be set to 1.
Finally correctly set Physical Slot Number to 1 since there is only one
port and zero value is reserved for ports within the same silicon as Root
Port which is not our case for Aardvark HW.
Likewise to the uvcvideo hostside driver, this patch is changing the
usb_request message of an non zero completion handler call from dev_info
to dev_warn.
The current limitation of possible number of requests being handled is
dependent on the gadget speed. It makes more sense to depend on the
typical frame size when calculating the number of requests. This patch
is changing this and is using the previous limits as boundaries for
reasonable minimum and maximum number of requests.
For a 1080p jpeg encoded video stream with a maximum imagesize of
e.g. 800kB with a maxburst of 8 and an multiplier of 1 the resulting
number of requests is calculated to 49.
The Broadcom BCM5750x NICs may be multi-function devices. They do not
advertise ACS capability. Peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
The trackpad of the given device sends continuous report of pointers
status as per wxn8 spec. However, the spec did not clarify when the
fingers are lifted so fast that between the interval of two report
frames fingers on pad reduced from >=2 to 0. The second last report
contains >=2 fingers with tip state 1 and the last report contains only
1 finger with tip state 0. Although this can happen unfrequently, a
quick fix will be improve the consistency to 100%. A quick fix is to
disable MT_QUIRK_ALWAYS_VALID and enable MT_QUIRK_NOT_SEEN_MEANS_UP.
Test for hid-tools is added in [1]
In addition to this, I2C device 04CA:00B1 may also need similar class
but with MT_QUIRK_FORCE_MULTI_INPUT disabled (but it does not harm to
enable it on non-multi-input device either). The respective owner has
been notified and a patch may coming soon after test.
In case of uni-directional time sync, TMU handshake is
initiated by upstream router. In case of bi-directional
time sync, TMU handshake is initiated by downstream router.
In order to handle correctly the case of uni-directional mode,
we avoid changing the upstream router's rate to off,
because it might have another downstream router plugged that is set to
uni-directional mode (and we don't want to change its mode).
Instead, we always change downstream router's rate.
Signed-off-by: Gil Fine <gil.fine@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
traps: Missing ENDBR: andw_ax_dx+0x0/0x10 [kvm]
------------[ cut here ]------------
kernel BUG at arch/x86/kernel/traps.c:253!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
<TASK>
asm_exc_control_protection+0x2b/0x30
RIP: 0010:andw_ax_dx+0x0/0x10 [kvm]
Code: c3 cc cc cc cc 0f 1f 44 00 00 66 0f 1f 00 48 19 d0 c3 cc cc cc
cc 0f 1f 40 00 f3 0f 1e fa 20 d0 c3 cc cc cc cc 0f 1f 44 00 00
<66> 0f 1f 00 66 21 d0 c3 cc cc cc cc 0f 1f 40 00 66 0f 1f 00 21
d0
Rather than reading the stats64 counters directly from the 32-bit
hardware, it's better to rely on the output produced by the periodic
ocelot_port_update_stats().
It would be even better to call ocelot_port_update_stats() right from
ocelot_get_stats64() to make sure we report the current values rather
than the ones from 2 seconds ago. But we need to export
ocelot_port_update_stats() from the switch lib towards the switchdev
driver for that, and future work will largely undo that.
There are more ocelot-based drivers waiting to be introduced, an example
of which is the SPI-controlled VSC7512. In that driver's case, it will
be impossible to call ocelot_port_update_stats() from ndo_get_stats64
context, since the latter is atomic, and reading the stats over SPI is
sleepable. So the compromise taken here, which will also hold going
forward, is to report 64-bit counters to stats64, which are not 100% up
to date.
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 2 methods can run concurrently, and one will change the window of
counters (SYS_STAT_CFG_STAT_VIEW) that the other sees. The fix is
similar to what commit 7fbf6795d127 ("net: mscc: ocelot: fix mutex lock
error during ethtool stats read") has done for ethtool -S.
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM does not support AArch32 EL0 on asymmetric systems. To that end,
prevent userspace from configuring a vCPU in such a state through
setting PSTATE.
It is already ABI that KVM rejects such a write on a system where
AArch32 EL0 is unsupported. Though the kernel's definition of a 32bit
system changed in commit 2122a833316f ("arm64: Allow mismatched
32-bit EL0 support"), KVM's did not.
If amdgpu_cs_vm_handling returns r != 0, then it will unlock the
bo_list_mutex inside the function amdgpu_cs_vm_handling and again on
amdgpu_cs_parser_fini. This problem results in the following
use-after-free problem:
Therefore, remove the mutex_unlock from the amdgpu_cs_vm_handling
function, so that amdgpu_cs_submit and amdgpu_cs_parser_fini can handle
the unlock.
Fixes: 90af0ca047f3 ("drm/amdgpu: Protect the amdgpu_bo_list list with a mutex v2") Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Maíra Canal <mairacanal@riseup.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the packet overhead is subtracted using unsigned arithmetic.
With a short sync pulse, this could underflow and wrap around to near
the maximal u16 value. Fix this by using signed subtraction. The call to
max() will correctly handle any negative numbers that are produced.
Apply the same fix to the other timings, even though those subtractions
are less likely to underflow.
Fixes: 133add5b5ad4 ("drm/sun4i: Add Allwinner A31 MIPI-DSI controller support") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220812031623.34057-1-samuel@sholland.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm_of_lvds_get_data_mapping() returns either negative value on
error or MEDIA_BUS_FMT_* otherwise. The check for 'ret' would also
catch the positive case of MEDIA_BUS_FMT_* and lead to probe failure
every time 'data-mapping' DT property is specified.
Fixes: 7c4dd0a266527 ("drm: of: Add drm_of_lvds_get_data_mapping") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org>
To: dri-devel@lists.freedesktop.org Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220801125419.167562-1-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
A list of devices to be reset is already created in
amdgpu_device_gpu_recover function. Creating another list with the
same nodes is incorrect and not supported in list_head. Instead, pass
the device list as part of reset context.
The kernel only manages the ccs state with lmem-only objects, however
the kernel should still take care not to leak the CCS state from the
previous user.
Fixes: 48760ffe923a ("drm/i915/gt: Clear compress metadata for Flat-ccs objects") Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Ramalingam C <ramalingam.c@intel.com> Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220727164346.282407-1-matthew.auld@intel.com
(cherry picked from commit 353819d85f87be46aeb9c1dd929d445a006fc6ec) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In this function, there are two refcount leak bugs:
(1) when breaking out of for_each_endpoint_of_node(), we need call
the of_node_put() for the 'ep';
(2) we should call of_node_put() for the reference returned by
of_graph_get_remote_port() when it is not used anymore.
Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by: Liang He <windhl@126.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220726010722.1319416-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When DCSS + MIPI_DSI is used, and the last bridge in the chain supports
HPD, we can see a "Hot plug detection already enabled" warning stack
trace dump that's thrown when DCSS is initialized.
The problem appeared when HPD was enabled by default in the
bridge_connector initialization, which made the
drm_bridge_connector_enable_hpd() call, in DCSS init path, redundant.
So, let's remove that call.
We should warn user-space that it is doing something wrong when trying
to activate sessions with identical parameters but WARN_ON_ONCE macro
can not be used here as it serves a different purpose.
So it would be good to replace it with netdev_warn_once() message.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Commit 36d4b36b6959 ("lib/nodemask: inline next_node_in() and
node_random()") refactored some code by moving node_random() from
lib/nodemask.c to include/linux/nodemask.h, thus requiring nodemask.h to
include random.h, which conditionally defines add_latent_entropy()
depending on whether the macro LATENT_ENTROPY_PLUGIN is defined.
This broke the build on powerpc, where nodemask.h is indirectly included
in arch/powerpc/kernel/prom_init.c, part of the early boot machinery that
is excluded from the latent entropy plugin using
DISABLE_LATENT_ENTROPY_PLUGIN. It turns out that while we add a gcc flag
to disable the actual plugin, we don't undefine LATENT_ENTROPY_PLUGIN.
This leads to the following:
CC arch/powerpc/kernel/prom_init.o
In file included from ./include/linux/nodemask.h:97,
from ./include/linux/mmzone.h:17,
from ./include/linux/gfp.h:7,
from ./include/linux/xarray.h:15,
from ./include/linux/radix-tree.h:21,
from ./include/linux/idr.h:15,
from ./include/linux/kernfs.h:12,
from ./include/linux/sysfs.h:16,
from ./include/linux/kobject.h:20,
from ./include/linux/pci.h:35,
from arch/powerpc/kernel/prom_init.c:24:
./include/linux/random.h: In function 'add_latent_entropy':
./include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
| ^~~~~~~~~~~~~~
| add_latent_entropy
./include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
make[2]: *** [scripts/Makefile.build:249: arch/powerpc/kernel/prom_init.o] Fehler 1
make[1]: *** [scripts/Makefile.build:465: arch/powerpc/kernel] Fehler 2
make: *** [Makefile:1855: arch/powerpc] Error 2
Change the DISABLE_LATENT_ENTROPY_PLUGIN flags to undefine
LATENT_ENTROPY_PLUGIN for files where the plugin is disabled.
projects / thirdparty / kernel / stable.git / log
