The controller driver nacked the master request but didn't emit a
STOP to end the transaction. The driver shall refuse the unsupported
requests and return the controller state to IDLE by emitting a STOP.
Signed-off-by: Stanley Chu <yschu@nuvoton.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20250318053606.3087121-4-yschu@nuvoton.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move to probe so we can check the PCI device type and
only apply the drm_firmware_drivers_only() check for
PCI DISPLAY classes. Also add a module parameter to
override the nomodeset kernel parameter as a workaround
for platforms that have this hardcoded on their kernel
command lines.
Reviewed-by: Kent Russell <kent.russell@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
PCI_CLASS_ACCELERATOR_PROCESSING devices won't ever be
the sysfb, so there is no need to free conflicting
apertures.
Reviewed-by: Kent Russell <kent.russell@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
We should never apply a minimum dispclk value while in
prepare_bandwidth or while displays are active. This is
always an optimizaiton for when all displays are disabled.
[HOW]
Defer dispclk optimization until safe_to_lower = true
and display_count reaches 0.
Since 0 has a special value in this logic (ie. no dispclk
required) we also need adjust the logic that clamps it for
the actual request to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Chris Park <chris.park@amd.com> Reviewed-by: Eric Yang <eric.yang@amd.com> Signed-off-by: Jing Zhou <Jing.Zhou@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch improve the returned error code of blkcg_policy_register().
1. Move the validation check for cpd/pd_alloc_fn and cpd/pd_free_fn
function pairs to the start of blkcg_policy_register(). This ensures
we immediately return -EINVAL if the function pairs are not correctly
provided, rather than returning -ENOSPC after locking and unlocking
mutexes unnecessarily.
Those locks should not contention any problems, as error of policy
registration is a super cold path.
When attempting to build a too long path we are currently returning
-ENOMEM, which is very odd and misleading. So update fs_path_ensure_buf()
to return -ENAMETOOLONG instead. Also, while at it, move the WARN_ON()
into the if statement's expression, as it makes it clear what is being
tested and also has the effect of adding 'unlikely' to the statement,
which allows the compiler to generate better code as this condition is
never expected to happen.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At btrfs_reclaim_bgs_work(), we are grabbing a block group's zone unusable
bytes while not under the protection of the block group's spinlock, so
this can trigger race reports from KCSAN (or similar tools) since that
field is typically updated while holding the lock, such as at
__btrfs_add_free_space_zoned() for example.
Fix this by grabbing the zone unusable bytes while we are still in the
critical section holding the block group's spinlock, which is right above
where we are currently grabbing it.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At close_ctree() after we have ran delayed iputs either explicitly through
calling btrfs_run_delayed_iputs() or later during the call to
btrfs_commit_super() or btrfs_error_commit_super(), we assert that the
delayed iputs list is empty.
We have (another) race where this assertion might fail because we have
queued an async write into the fs_info->workers workqueue. Here's how it
happens:
1) We are submitting a data bio for an inode that is not the data
relocation inode, so we call btrfs_wq_submit_bio();
2) btrfs_wq_submit_bio() submits a work for the fs_info->workers queue
that will run run_one_async_done();
3) We enter close_ctree(), flush several work queues except
fs_info->workers, explicitly run delayed iputs with a call to
btrfs_run_delayed_iputs() and then again shortly after by calling
btrfs_commit_super() or btrfs_error_commit_super(), which also run
delayed iputs;
4) run_one_async_done() is executed in the work queue, and because there
was an IO error (bio->bi_status is not 0) it calls btrfs_bio_end_io(),
which drops the final reference on the associated ordered extent by
calling btrfs_put_ordered_extent() - and that adds a delayed iput for
the inode;
5) At close_ctree() we find that after stopping the cleaner and
transaction kthreads the delayed iputs list is not empty, failing the
following assertion:
ASSERT(list_empty(&fs_info->delayed_iputs));
Fix this by flushing the fs_info->workers workqueue before running delayed
iputs at close_ctree().
David reported this when running generic/648, which exercises IO error
paths by using the DM error table.
Reported-by: David Sterba <dsterba@suse.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[BUG]
Even after all the error fixes related the
"ASSERT(list_empty(&fs_info->delayed_iputs));" in close_ctree(), I can
still hit it reliably with my experimental 2K block size.
[CAUSE]
In my case, all the error is triggered after the fs is already in error
status.
I find the following call trace to be the cause of race:
The root cause is that, btrfs_wait_ordered_roots() only wait for
ordered extents to finish their IOs, not to wait for them to finish and
removed.
[FIX]
Since btrfs_error_commit_super() will flush and wait for all ordered
extents, it should be executed early, before we start flushing the
workqueues.
And since btrfs_error_commit_super() now runs early, there is no need to
run btrfs_run_delayed_iputs() inside it, so just remove the
btrfs_run_delayed_iputs() call from btrfs_error_commit_super().
Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The inline function btrfs_is_testing() is hardcoded to return 0 if
CONFIG_BTRFS_FS_RUN_SANITY_TESTS is not set. Currently we're relying on
the compiler optimizing out the call to alloc_test_extent_buffer() in
btrfs_find_create_tree_block(), as it's not been defined (it's behind an
#ifdef).
Add a stub version of alloc_test_extent_buffer() to avoid linker errors
on non-standard optimization levels. This problem was seen on GCC 14
with -O0 and is helps to see symbols that would be otherwise optimized
out.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Mark Harmstone <maharmstone@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the async discard machinery owns a ref to the block_group
when the block_group is queued on a discard list. However, to handle
races with discard cancellation and the discard workfn, we have a
specific logic to detect that the block_group is *currently* running in
the workfn, to protect the workfn's usage amidst cancellation.
As far as I can tell, this doesn't have any overt bugs (though
finish_discard_pass() and remove_from_discard_list() racing can have a
surprising outcome for the caller of remove_from_discard_list() in that
it is again added at the end).
But it is needlessly complicated to rely on locking and the nullity of
discard_ctl->block_group. Simplify this significantly by just taking a
refcount while we are in the workfn and unconditionally drop it in both
the remove and workfn paths, regardless of if they race.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the I2C QUP controller is used together with a DMA engine it needs
to vote for the interconnect path to the DRAM. Otherwise it may be
unable to access the memory quickly enough.
The requested peak bandwidth is dependent on the I2C core clock.
To avoid sending votes too often the bandwidth is always requested when
a DMA transfer starts, but dropped only on runtime suspend. Runtime
suspend should only happen if no transfer is active. After resumption we
can defer the next vote until the first DMA transfer actually happens.
The implementation is largely identical to the one introduced for
spi-qup in commit ecdaa9473019 ("spi: qup: Vote for interconnect
bandwidth to DRAM") since both drivers represent the same hardware
block.
At least with CONFIG_PHYSICAL_START=0x100000, if there is < 4 MiB of
contiguous free memory available at this point, the kernel will crash
and burn because memblock_phys_alloc_range() returns 0 on failure,
which leads memblock_phys_free() to throw the first 4 MiB of physical
memory to the wolves.
At a minimum it should fail gracefully with a meaningful diagnostic,
but in fact everything seems to work fine without the weird reserve
allocation.
Signed-off-by: Philip Redkin <me@rarity.fan> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Rik van Riel <riel@surriel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lore.kernel.org/r/94b3e98f-96a7-3560-1f76-349eb95ccf7f@rarity.fan Signed-off-by: Sasha Levin <sashal@kernel.org>
Offsets 0x60 and 0x64 are used internally by kernel drivers that call
the amd_smn_read() and amd_smn_write() functions. If userspace accesses
the regions at the same time as the kernel it may cause malfunctions in
drivers using the offsets.
Add these offsets to the exclusions so that the kernel is tainted if a
non locked down userspace tries to access them.
The Family model check to read the processor flag MSR is misleading and
potentially incorrect. It doesn't consider Family while comparing the
model number. The original check did have a Family number but it got
lost/moved during refactoring.
intel_collect_cpu_info() is called through multiple paths such as early
initialization, CPU hotplug as well as IFS image load. Some of these
flows would be error prone due to the ambiguous check.
Correct the processor flag scan check to use a Family number and update
it to a VFM based one to make it more readable.
__ASSEMBLY__ is only defined by the Makefile of the kernel, so
this is not really useful for UAPI headers (unless the userspace
Makefile defines it, too). Let's switch to __ASSEMBLER__ which
gets set automatically by the compiler when compiling assembly
code.
While the GCC and Clang compilers already define __ASSEMBLER__
automatically when compiling assembly code, __ASSEMBLY__ is a
macro that only gets defined by the Makefiles in the kernel.
This can be very confusing when switching between userspace
and kernelspace coding, or when dealing with UAPI headers that
rather should use __ASSEMBLER__ instead. So let's standardize on
the __ASSEMBLER__ macro that is provided by the compilers now.
This is mostly a mechanical patch (done with a simple "sed -i"
statement), with some manual tweaks in <asm/frame.h>, <asm/hw_irq.h>
and <asm/setup.h> that mentioned this macro in comments with some
missing underscores.
Signed-off-by: Thomas Huth <thuth@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Brian Gerst <brgerst@gmail.com> Cc: Juergen Gross <jgross@suse.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/20250314071013.1575167-38-thuth@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The mt7925 sometimes fails to enter low power mode during suspend.
This is caused by the chip firmware sending an additional ACK event
to the host after processing the suspend command. Due to timing issues,
this event may not reach the host, causing the chip to get stuck.
To resolve this, the ACK flag in the suspend command is removed,
as it is not needed in the MT7925 architecture. This prevents the
firmware from sending the additional ACK event, ensuring the device
can reliably enter low power mode during suspend.
System suspend failures may occur due to inappropriate
handling of traffic not idle event by the WiFi driver.
The WiFi firmware's traffic not idle indication does
not need to be tied to suspend. Fix the flow to ensuring
the system can suspend properly.
Size of MPDU/PPDU TXS is 12 DWs.
In mt7996/mt7992, last 4 DWs are reserved, so TXS size was mistakenly
considered to be 8 DWs. However, in mt7990, 9th DW of TXS starts to be used.
The interrupt status polling is unreliable, which can cause status events
to get lost. On all newer chips, txs-timeout is an indication that the
packet was either never sent, or never acked.
Fixes issues with inactivity polling.
cgroup_rstat_flush_locked() grabs the irq safe cgroup_rstat_lock while
iterating all possible cpus. It only drops the lock if there is
scheduler or spin lock contention. If neither, then interrupts can be
disabled for a long time. On large machines this can disable interrupts
for a long enough time to drop network packets. On 400+ CPU machines
I've seen interrupt disabled for over 40 msec.
Prevent rstat from disabling interrupts while processing all possible
cpus. Instead drop and reacquire cgroup_rstat_lock for each cpu. This
approach was previously discussed in
https://lore.kernel.org/lkml/ZBz%2FV5a7%2F6PZeM7S@slm.duckdns.org/,
though this was in the context of an non-irq rstat spin lock.
Benchmark this change with:
1) a single stat_reader process with 400 threads, each reading a test
memcg's memory.stat repeatedly for 10 seconds.
2) 400 memory hog processes running in the test memcg and repeatedly
charging memory until oom killed. Then they repeat charging and oom
killing.
With this patch the CONFIG_IRQSOFF_TRACER doesn't find rstat to be the
longest holder. The longest irqs-off holder has irqs disabled for
4142 usec, a huge reduction from previous 45341 usec rstat finding.
Running stat_reader memory.stat reader for 10 seconds:
- without memory hogs: 9.84M accesses => 12.7M accesses
- with memory hogs: 9.46M accesses => 11.1M accesses
The throughput of memory.stat access improves.
The mode of memory.stat access latency after grouping by of 2 buckets:
- without memory hogs: 64 usec => 16 usec
- with memory hogs: 64 usec => 8 usec
The memory.stat latency improves.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Greg Thelen <gthelen@google.com> Tested-by: Greg Thelen <gthelen@google.com> Acked-by: Michal Koutný <mkoutny@suse.com> Reviewed-by: Yosry Ahmed <yosry.ahmed@linux.dev> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SD spec version 6.0 section 6.4.1.5 requires that Vdd must be
lowered to less than 0.5V for a minimum of 1 ms when powering off a
card. Increase wait to 15 ms so that voltage has time to drain down
to 0.5V and cards can power off correctly. Issues with voltage drain
time were only observed on Apollo Lake and Bay Trail host controllers
so this fix is limited to those devices.
Creating the keep-alive thread in vchiq_platform_init_state have
the following advantages:
- abort driver probe if kthread_create fails (more consistent behavior)
- make resource release process easier
Since vchiq_keepalive_thread_func is defined below
vchiq_platform_init_state, the latter must be moved.
This is another attempt trying to make pidfd polling for multi-threaded
exec and premature thread-group leader exit consistent.
A quick recap of these two cases:
(1) During a multi-threaded exec by a subthread, i.e., non-thread-group
leader thread, all other threads in the thread-group including the
thread-group leader are killed and the struct pid of the
thread-group leader will be taken over by the subthread that called
exec. IOW, two tasks change their TIDs.
(2) A premature thread-group leader exit means that the thread-group
leader exited before all of the other subthreads in the thread-group
have exited.
Both cases lead to inconsistencies for pidfd polling with PIDFD_THREAD.
Any caller that holds a PIDFD_THREAD pidfd to the current thread-group
leader may or may not see an exit notification on the file descriptor
depending on when poll is performed. If the poll is performed before the
exec of the subthread has concluded an exit notification is generated
for the old thread-group leader. If the poll is performed after the exec
of the subthread has concluded no exit notification is generated for the
old thread-group leader.
The correct behavior would be to simply not generate an exit
notification on the struct pid of a subhthread exec because the struct
pid is taken over by the subthread and thus remains alive.
But this is difficult to handle because a thread-group may exit
prematurely as mentioned in (2). In that case an exit notification is
reliably generated but the subthreads may continue to run for an
indeterminate amount of time and thus also may exec at some point.
So far there was no way to distinguish between (1) and (2) internally.
This tiny series tries to address this problem by discarding
PIDFD_THREAD notification on premature thread-group leader exit.
If that works correctly then no exit notifications are generated for a
PIDFD_THREAD pidfd for a thread-group leader until all subthreads have
been reaped. If a subthread should exec aftewards no exit notification
will be generated until that task exits or it creates subthreads and
repeates the cycle.
If a faulty CXL memory device returns a broken zero LSA size in its
memory device information (Identify Memory Device (Opcode 4000h), CXL
spec. 3.1, 8.2.9.9.1.1), a divide error occurs in the libnvdimm
driver:
implied that the file system was previously mounted read/write and was
now remounted read-only, when it could have been some other mount
state that had changed by the "mount -o remount" operation. Fix this
by only logging "ro"or "r/w" when it has changed.
The current hypercall interface for doing PCI device operations always uses
a segment field that has a 16 bit width. However on Linux there are buses
like VMD that hook up devices into the PCI hierarchy at segment >= 0x10000,
after the maximum possible segment enumerated in ACPI.
Attempting to register or manage those devices with Xen would result in
errors at best, or overlaps with existing devices living on the truncated
equivalent segment values. Note also that the VMD segment numbers are
arbitrarily assigned by the OS, and hence there would need to be some
negotiation between Xen and the OS to agree on how to enumerate VMD
segments and devices behind them.
Skip notifying Xen about those devices. Given how VMD bridges can
multiplex interrupts on behalf of devices behind them there's no need for
Xen to be aware of such devices for them to be usable by Linux.
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
Clause instructions with precise memory enabled currently hang the
shader so set capabilities flag to disabled since it's unsafe to use
for debugging.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com> Tested-by: Lancelot Six <lancelot.six@amd.com> Reviewed-by: Harish Kasiviswanathan <harish.kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the critical submission path memory allocations can't wait for
reclaim since that can potentially wait for submissions to finish.
Finally clean that up and mark most memory allocations in the critical
path with GFP_NOWAIT. The only exception left is the dma_fence_array()
used when no VMID is available, but that will be cleaned up later on.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Limiting the number of available VMIDs to enforce isolation causes some
issues with gang submit and applying certain HW workarounds which
require multiple VMIDs to work correctly.
So instead start to track all submissions to the relevant engines in a
per partition data structure and use the dma_fences of the submissions
to enforce isolation similar to what a VMID limit does.
v2: use ~0l for jobs without isolation to distinct it from kernel
submissions which uses NULL for the owner. Add some warning when we
are OOM.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the client should see an ENETDOWN when trying to connect to the data
server, it might still be able to talk to the metadata server through
another NIC. If so, report the error.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Tested-by: Jeff Layton <jlayton@kernel.org> Acked-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the current settings, the I2C buses are achieving around 370KHz
instead of the expected 400KHz. For 100KHz and 1MHz, the settings are
now more compliant and adhere to the Qualcomm’s internal programming
guide.
Update the I2C frequency table to align with the recommended values
outlined in the I2C hardware programming guide, ensuring proper
communication and performance.
Disable it due to it dose not meet ZRX-DC specification. If it is enabled,
device will exit L1 substate every 100ms. Disable it for saving more power
in L1 substate.
Signed-off-by: ChunHao Lin <hau@realtek.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://patch.msgid.link/20250318083721.4127-3-hau@realtek.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most systems' PCIe outbound map windows have non-zero physical addresses,
but the possibility of encountering zero increased after following commit
("PCI: dwc: Use parent_bus_offset").
'ep->outbound_addr[n]', representing 'parent_bus_address', might be 0 on
some hardware, which trims high address bits through bus fabric before
sending to the PCIe controller.
Replace the iteration logic with 'for_each_set_bit()' to ensure only
allocated map windows are iterated when determining the ATU index from a
given address.
Use bitmap_free() to free memory allocated with bitmap_zalloc_node().
This fixes memtrack error:
mtl rsc inconsistency: memtrack_free: .../drivers/net/ethernet/mellanox/mlx5/core/en_main.c::466: kfree for unknown address=0xFFFF0000CA3619E8, device=0x0
Signed-off-by: Mark Zhang <markzhang@nvidia.com> Reviewed-by: Maher Sanalla <msanalla@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Link: https://patch.msgid.link/1742412199-159596-3-git-send-email-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If opts.uaccess isn't set, the uaccess validation is disabled, but only
partially: it doesn't read the uaccess_safe_builtin list but still tries
to do the validation. Disable it completely to prevent false warnings.
0c1d7a2c2d32 ("lockdep: Remove softirq accounting on PREEMPT_RT.")
the wait context test for mutex usage within "in softirq context" fails
as it references @softirq_context:
| wait context tests |
--------------------------------------------------------------------------
| rcu | raw | spin |mutex |
--------------------------------------------------------------------------
in hardirq context: ok | ok | ok | ok |
in hardirq context (not threaded): ok | ok | ok | ok |
in softirq context: ok | ok | ok |FAILED|
As a fix, add lockdep map for BH disabled section. This fixes the
issue by letting us catch cases when local_bh_disable() gets called
with preemption disabled where local_lock doesn't get acquired.
In the case of "in softirq context" selftest, local_bh_disable() was
being called with preemption disable as it's early in the boot.
[ boqun: Move the lockdep annotations into __local_bh_*() to avoid false
positives because of unpaired local_bh_disable() reported by
Borislav Petkov and Peter Zijlstra, and make bh_lock_map
only exist for PREEMPT_RT. ]
[ mingo: Restored authorship and improved the bh_lock_map definition. ]
Executing dql_reset after setting a non-zero value for limit_min can
lead to an unreasonable situation where dql->limit is less than
dql->limit_min.
For instance, after setting
/sys/class/net/eth*/queues/tx-0/byte_queue_limits/limit_min,
an ifconfig down/up operation might cause the ethernet driver to call
netdev_tx_reset_queue, which in turn invokes dql_reset.
In this case, dql->limit is reset to 0 while dql->limit_min remains
non-zero value, which is unexpected. The limit should always be
greater than or equal to limit_min.
Using Clement's new validation callbacks, support checking that
dependencies have been satisfied for the vector extensions. From the
kernel's perfective, it's not required to differentiate between the
conditions for all the various vector subsets - it's the firmware's job
to not report impossible combinations. Instead, the kernel only has to
check that the correct config options are enabled and to enforce its
requirement of the d extension being present for FPU support.
Since vector will now be disabled proactively, there's no need to clear
the bit in elf_hwcap in riscv_fill_hwcap() any longer.
A SCO connection without the proper voice_setting can cause
the controller to lock up.
Signed-off-by: Pedro Nishiyama <nishiyama.pedro@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure interrupts are not re-enabled when the IRQ handler has already been
removed. This prevents unexpected IRQ handler execution due to stale or
unhandled interrupts.
Modify btmtksdio_txrx_work to check if bdev->func->irq_handler exists
before calling sdio_writel to enable interrupts.
Co-developed-by: Pedro Tsai <pedro.tsai@mediatek.com> Signed-off-by: Pedro Tsai <pedro.tsai@mediatek.com> Co-developed-by: Felix Freimann <felix.freimann@mediatek.com> Signed-off-by: Felix Freimann <felix.freimann@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enable power-down of TMU (Thermal Management Unit) for TMU version 2 during
system suspend to save power. Save approximately 4.3mW on VDD_ANA_1P8 on
i.MX93 platforms.
Interrupts are enabled per sensor in lvts_update_irq_mask() as needed,
there's no point in enabling all of them during initialization. Change
the MONINT register initial value so all sensor interrupts start
disabled.
In case of an AQR105-based device, create a software node for the mdio
function, with a child node for the Aquantia AQR105 PHY, providing a
firmware-name (and a bit more, which may be used for future checks) to
allow the PHY to load a MAC specific firmware from the file system.
The name of the PHY software node follows the naming convention suggested
in the patch for the mdiobus_scan function (in the same patch series).
Add the PCI-ID of the AQR105-based Tehuti TN4010 cards to allow loading
of the tn40xx driver on these cards. Here, I chose the detailed definition
with the subvendor ID similar to the QT2025 cards with the PCI-ID
TEHUTI:0x4022, because there is a card with an AQ2104 hiding amongst the
AQR105 cards, and they all come with the same PCI-ID (TEHUTI:0x4025). But
the AQ2104 is currently not supported.
Previously, the condition for invalidating the tx flow in
mctp_i2c_invalidate_tx_flow() checked if `rc` was nonzero.
However, this could incorrectly trigger the invalidation
even when `rc > 0` was returned as a success status.
This patch updates the condition to explicitly check for `rc < 0`,
ensuring that only error cases trigger the invalidation.
Signed-off-by: Daniel Hsu <Daniel-Hsu@quantatw.com> Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
VI sense port on WSA883x speaker takes only one channel, so use 0x1 as
channel mask. This fixes garbage being recorded by the speaker when
testing the VI sense feedback path.
VI sense port on WSA883x speaker takes only one channel, so use 0x1 as
channel mask. This fixes garbage being recorded by the speaker when
testing the VI sense feedback path.
The autobind setting was supposed to be determined in rpc_create(),
since commit c2866763b402 ("SUNRPC: use sockaddr + size when creating
remote transport endpoints").
Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a containerised process is killed and causes an ENETUNREACH or
ENETDOWN error to be propagated to the state manager, then mark the
nfs_client as being dead so that we don't loop in functions that are
expecting recovery to succeed.
Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently ->get_acl() callback always create request for OWNER, GROUP and
DACL, even when only DACLs was requested by user. Change API callback to
request only information for which the caller asked. Therefore when only
DACLs requested, then SMB client will prepare and send DACL-only request.
This change fixes retrieving of "system.cifs_acl" and "system.smb3_acl"
xattrs to contain only DACL structure as documented.
Note that setting/changing of "system.cifs_acl" and "system.smb3_acl"
xattrs already takes only DACL structure and ignores all other fields.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function ip_rfc1001_connect() which establish NetBIOS session for SMB
connections, currently uses smb_send() function for sending NetBIOS Session
Request packet. This function expects that the passed buffer is SMB packet
and for SMB2+ connections it mangles packet header, which breaks prepared
NetBIOS Session Request packet. Result is that this function send garbage
packet for SMB2+ connection, which SMB2+ server cannot parse. That function
is not mangling packets for SMB1 connections, so it somehow works for SMB1.
Fix this problem and instead of smb_send(), use smb_send_kvec() function
which does not mangle prepared packet, this function send them as is. Just
API of this function takes struct msghdr (kvec) instead of packet buffer.
[MS-SMB2] specification allows SMB2 protocol to use NetBIOS as a transport
protocol. NetBIOS can be used over TCP via port 139. So this is a valid
configuration, just not so common. And even recent Windows versions (e.g.
Windows Server 2022) still supports this configuration: SMB over TCP port
139, including for modern SMB2 and SMB3 dialects.
This change fixes SMB2 and SMB3 connections over TCP port 139 which
requires establishing of NetBIOS session. Tested that this change fixes
establishing of SMB2 and SMB3 connections with Windows Server 2022.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Windows SMB servers (including SMB2+) which are working over RFC1001
require that Netbios server name specified in RFC1001 Session Request
packet is same as the UNC host name. Netbios server name can be already
specified manually via -o servern= option.
With this change the RFC1001 server name is set automatically by extracting
the hostname from the mount source.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I was wondering why there's garbage at the bottom of the screen when
tile blitting is used with an odd mode like 1080, 600 or 200. Sure there's
only space for half a tile but the same area is clean when the buffer
is bitmap.
Then later I found that it's supposed to be cleaned but that's not
implemented. So I took what's in bitblit and adapted it for tileblit.
This implementation was tested for both the horizontal and vertical case,
and now does the same as what's done for bitmap buffers.
If anyone is interested to reproduce the problem then I could bet that'd
be on a S3 or Ark. Just set up a mode with an odd line count and make
sure that the virtual size covers the complete tile at the bottom. E.g.
for 600 lines that's 608 virtual lines for a 16 tall tile. Then the
bottom area should be cleaned.
For the right side it's more difficult as there the drivers won't let an
odd size happen, unless the code is modified. But once it reports back a
few pixel columns short then fbcon won't use the last column. With the
patch that column is now clean.
Btw. the virtual size should be rounded up by the driver for both axes
(not only the horizontal) so that it's dividable by the tile size.
That's a driver bug but correcting it is not in scope for this patch.
The erase colour calculation for fbcon clearing should use get_color instead
of attr_col_ec, like everything else. The latter is similar but is not correct.
For example it's missing the depth dependent remapping and doesn't care about
blanking.
The problem can be reproduced by setting up the background colour to grey
(vt.color=0x70) and having an fbcon console set to 2bpp (4 shades of gray).
Now the background attribute should be 1 (dark gray) on the console.
If the screen is scrolled when pressing enter in a shell prompt at the bottom
line then the new line is cleared using colour 7 instead of 1. That's not
something fillrect likes (at 2bbp it expect 0-3) so the result is interesting.
This patch switches to get_color with vc_video_erase_char to determine the
erase colour from attr_col_ec. That makes the latter function redundant as
no other users were left.
NOMMU kernels currently cannot access memory below the kernel link
address. Remove this restriction by setting PAGE_OFFSET to the actual
start of RAM, as determined from the devicetree. The kernel link address
must be a constant, so keep using CONFIG_PAGE_OFFSET for that purpose.
In case of error, of_parse_phandle_with_args() returns -EINVAL when the
passed index is negative, or -ENOENT when the index is for an empty
phandle. The mailbox core overwrote the error return code with a less
precise -ENODEV. Use the error returned code from
of_parse_phandle_with_args().
The Platform Communication Channel (PCC) mailbox driver currently uses
ioremap() to map channel shared memory regions. However it is preferred
to use acpi_os_ioremap(), which is mapping function specific to EFI/ACPI
defined memory regions. It ensures that the correct memory attributes
are applied when mapping ACPI-provided regions.
While at it, also add checks for handling any errors with the mapping.
Acked-by: Huisong Li <lihuisong@huawei.com> Tested-by: Huisong Li <lihuisong@huawei.com> Tested-by: Adam Young <admiyo@os.amperecomputing.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
TPM2 sessions have been flushed lazily since commit df745e25098dc ("tpm:
Lazily flush the auth session"). If /dev/tpm{rm}0 is not accessed
in-between two in-kernel calls, it is possible that a TPM2 session is
re-started before the previous one has been completed.
This causes a spurios warning in a legit run-time condition, which is also
correctly addressed with a fast return path:
[ 2.944047] tpm tpm0: auth session is active
Address the issue by changing dev_warn_once() call to a dev_dbg_once()
call.
[jarkko: Rewrote the commit message, and instead of dropping converted
to a debug message.] Signed-off-by: Jonathan McDowell <noodles@meta.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Intel Over-Clocking Watchdogs are described in ACPI tables by both the
generic PNP0C02 _CID and their ACPI _HID. The presence of the _CID then
causes the PNP scan handler to attach to the watchdog, preventing the
actual watchdog driver from binding. Address this by adding the ACPI
_HIDs to the list of non-PNP devices, so that the PNP scan handler is
bypassed.
Note that these watchdogs can be described by multiple _HIDs for what
seems to be identical hardware. This commit is not a complete list of
all the possible watchdog ACPI _HIDs.
Binary printing functions are using printf() type of format, and compiler
is not happy about them as is:
kernel/trace/trace.c:3292:9: error: function ‘trace_vbprintk’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
kernel/trace/trace_seq.c:182:9: error: function ‘trace_seq_bprintf’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
Fix the compilation errors by adding __printf() attribute.
While at it, move existing __printf() attributes from the implementations
to the declarations. IT also fixes incorrect attribute parameters that are
used for trace_array_printk().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Kees Cook <kees@kernel.org> Reviewed-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20250321144822.324050-4-andriy.shevchenko@linux.intel.com Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of saving off the text and data pointers and using them to compare
with the current boot's text and data pointers, just save off the KASLR
offset. Then that can be used to figure out how to read the previous boots
buffer.
The last_boot_info will now show this offset, but only if it is for a
previous boot:
PASID usage requires PASID support in both device and IOMMU. Since the
iommu drivers always enable the PASID capability for the device if it
is supported, this extends the IOMMU_GET_HW_INFO to report the PASID
capability to userspace. Also, enhances the selftest accordingly.
Link: https://patch.msgid.link/r/20250321180143.8468-5-yi.l.liu@intel.com Cc: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Tested-by: Zhangfei Gao <zhangfei.gao@linaro.org> #aarch64 platform Tested-by: Nicolin Chen <nicolinc@nvidia.com> Signed-off-by: Yi Liu <yi.l.liu@intel.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HIP09 processor is vulnerable to the Spectre-BHB (Branch History
Buffer) attack, which can be exploited to leak information through
branch prediction side channels. This commit adds the MIDR of HIP09
to the list for software mitigation.
It's risky to have msg request opcode set to garbage, so at least
initialise it to nop. Later we might want to add a user inaccessible
opcode for such cases.
With commit 11a347fb6cef ("exfat: change to get file size from DataLength"),
exfat_get_block() can now handle valid_size. However, most partial
unwritten blocks that could be mapped with other blocks are being
inefficiently processed separately as individual blocks.
Except for partial unwritten blocks that require independent processing,
let's handle them simply as before.
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com> Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During mount option processing and negotiation with the server, the
original user-specified rsize/wsize values were being modified directly.
This makes it impossible to recover these values after a connection
reset, leading to potential degraded performance after reconnection.
The other problem is that When negotiating read and write sizes, there are
cases where the negotiated values might calculate to zero, especially
during reconnection when server->max_read or server->max_write might be
reset. In general, these values come from the negotiation response.
According to MS-SMB2 specification, these values should be at least 65536
bytes.
This patch improves IO parameter handling:
1. Adds vol_rsize and vol_wsize fields to store the original user-specified
values separately from the negotiated values
2. Uses got_rsize/got_wsize flags to determine if values were
user-specified rather than checking for non-zero values, which is more
reliable
3. Adds a prevent_zero_iosize() helper function to ensure IO sizes are
never negotiated down to zero, which could happen in edge cases like
when server->max_read/write is zero
The changes make the CIFS client more resilient to unusual server
responses and reconnection scenarios, preventing potential failures
when IO sizes are calculated to be zero.
Signed-off-by: Wang Zhaolong <wangzhaolong1@huawei.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SMB negotiate retry functionality in cifs_negotiate() is currently broken
and does not work when doing socket reconnect. Caller of this function,
which is cifs_negotiate_protocol() requires that tcpStatus after successful
execution of negotiate callback stay in CifsInNegotiate. But if the
CIFSSMBNegotiate() called from cifs_negotiate() fails due to connection
issues then tcpStatus is changed as so repeated CIFSSMBNegotiate() call
does not help.
Fix this problem by moving retrying code from negotiate callback (which is
either cifs_negotiate() or smb2_negotiate()) to cifs_negotiate_protocol()
which is caller of those callbacks. This allows to properly handle and
implement correct transistions between tcpStatus states as function
cifs_negotiate_protocol() already handles it.
With this change, cifs_negotiate_protocol() now handles also -EAGAIN error
set by the RFC1002_NEGATIVE_SESSION_RESPONSE processing after reconnecting
with NetBIOS session.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Old SMB1 servers without CAP_NT_SMBS do not support CIFS_open() function
and instead SMBLegacyOpen() needs to be used. This logic is already handled
in cifs_open_file() function, which is server->ops->open callback function.
So for querying and creating MF symlinks use open callback function instead
of CIFS_open() function directly.
This change fixes querying and creating new MF symlinks on Windows 98.
Currently cifs_query_mf_symlink() is not able to detect MF symlink and
cifs_create_mf_symlink() is failing with EIO error.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some operations, like WRITE, does not require FILE_READ_ATTRIBUTES access.
So when FILE_READ_ATTRIBUTES is not explicitly requested for
smb2_open_file() then first try to do SMB2 CREATE with FILE_READ_ATTRIBUTES
access (like it was before) and then fallback to SMB2 CREATE without
FILE_READ_ATTRIBUTES access (less common case).
This change allows to complete WRITE operation to a file when it does not
grant FILE_READ_ATTRIBUTES permission and its parent directory does not
grant READ_DATA permission (parent directory READ_DATA is implicit grant of
child FILE_READ_ATTRIBUTES permission).
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
