After commit 84a9582fd203 ("serial: core: Start managing serial controllers
to enable runtime PM") serial drivers need to provide a device in
struct uart_port.dev otherwise an oops happens. To fix this issue
for ip22zilog driver switch driver to a platform driver and setup
the serial device in sgi-ip22 code.
The thunderbolt driver sets up device link dependencies from hotplug ports
to the Host Router (aka Native Host Interface, NHI). When resuming from
system sleep, this allows the Host Router to re-establish tunnels to
attached Thunderbolt devices before the hotplug ports resume.
To identify the hotplug ports, the driver utilizes the is_hotplug_bridge
flag which also encompasses ACPI slots handled by the ACPI hotplug driver.
Thunderbolt hotplug ports are always Hot-Plug Capable PCIe ports, so it is
more apt to identify them with the is_pciehp flag.
Similarly, hotplug ports on older Thunderbolt controllers have broken MSI
support and are quirked to use legacy INTx interrupts instead. The quirk
identifies them with is_hotplug_bridge, even though all affected ports are
also matched by is_pciehp. So use is_pciehp here as well.
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Acked-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250811-restricted-pointers-net-v5-1-2e2fdc7d3f2c@linutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
stmmac_hw_setup() may return 0 on success and an appropriate negative
integer as defined in errno.h file on failure, just check it and then
return early if failed in stmmac_resume().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Huacai Chen <chenhuacai@loongson.cn> Link: https://patch.msgid.link/20250811073506.27513-2-yangtiezhu@loongson.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
emulate_vsyscall() expects to see X86_PF_INSTR in PFEC on a vsyscall
page fault, but the CPU does not report X86_PF_INSTR if neither
X86_FEATURE_NX nor X86_FEATURE_SMEP are enabled.
X86_FEATURE_NX should be enabled on nearly all 64-bit CPUs, except for
early P4 processors that did not support this feature.
Instead of explicitly checking for X86_PF_INSTR, compare the fault
address to RIP.
On machines with X86_FEATURE_NX enabled, issue a warning if RIP is equal
to fault address but X86_PF_INSTR is absent.
After a Fatal Error has been reported by a device and has been recovered
through a Secondary Bus Reset, AER updates the device's error_state to
pci_channel_io_normal before invoking its driver's ->resume() callback.
By contrast, EEH updates the error_state earlier, namely after resetting
the device and before invoking its driver's ->slot_reset() callback.
Commit c58dc575f3c8 ("powerpc/pseries: Set error_state to
pci_channel_io_normal in eeh_report_reset()") explains in great detail
that the earlier invocation is necessitated by various drivers checking
accessibility of the device with pci_channel_offline() and avoiding
accesses if it returns true. It returns true for any other error_state
than pci_channel_io_normal.
The device should be accessible already after reset, hence the reasoning
is that it's safe to update the error_state immediately afterwards.
This deviation between AER and EEH seems problematic because drivers
behave differently depending on which error recovery mechanism the
platform uses. Three drivers have gone so far as to update the
error_state themselves, presumably to work around AER's behavior.
For consistency, amend AER to update the error_state at the same recovery
steps as EEH. Drop the now unnecessary workaround from the three drivers.
Keep updating the error_state before ->resume() in case ->error_detected()
or ->mmio_enabled() return PCI_ERS_RESULT_RECOVERED, which causes
->slot_reset() to be skipped. There are drivers doing this even for Fatal
Errors, e.g. mhi_pci_error_detected().
In rare servicing scenarios, the hardware may delete the
state of the GSI QP, preventing it from generating CQEs
for pending send WRs. Since WRs submitted to the GSI QP
hold CM resources, the device cannot be removed until
those WRs are completed. This patch marks all pending
send WRs as failed, allowing the GSI QP to release the CM
resources and enabling safe device removal.
TIDSS uses crtc_* fields to propagate its registers and set the
clock rates. So set the CRTC modesetting timing parameters with
the adjusted mode when needed, to set correct values.
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com> Link: https://lore.kernel.org/r/20250624080402.302526-1-j-choudhary@ti.com Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the cdns-dsi does not support DSI burst mode, the burst mode is
essentially DSI event mode with more versatile clocking and timings.
Thus cdns-dsi doesn't need to fail if the DSI peripheral driver requests
MIPI_DSI_MODE_VIDEO_BURST.
In my particular use case, this allows the use of ti-sn65dsi83 driver.
The driver tries to calculate the value for REG_WAKEUP_TIME. However,
the calculation itself is not correct, and to add on it, the resulting
value is almost always larger than the field's size, so the actual
result is more or less random.
According to the docs, figuring out the value for REG_WAKEUP_TIME
requires HW characterization and there's no way to have a generic
algorithm to come up with the value. That doesn't help at all...
However, we know that the value must be smaller than the line time, and,
at least in my understanding, the proper value for it is quite small.
Testing shows that setting it to 1/10 of the line time seems to work
well. All video modes from my HDMI monitor work with this algorithm.
Hopefully we'll get more information on how to calculate the value, and
we can then update this.
Use the crtc_* fields from drm_display_mode, instead of the "logical"
fields. This shouldn't change anything in practice, but afaiu the crtc_*
fields are the correct ones to use here.
The v4l2_fh initialized and added in vpu_v4l2_open() is delete and
cleaned up when the last reference to the vpu_inst is released. This may
happen later than at vpu_v4l2_close() time.
Not deleting and cleaning up the v4l2_fh when closing the file handle to
the video device is not ideal, as the v4l2_fh will still be present in
the video device's fh_list, and will store a copy of events queued to
the video device. There may also be other side effects of keeping alive
an object that represents an open file handle after the file handle is
closed.
The v4l2_fh instance is embedded in the vpu_inst structure, and is
accessed in two different ways:
- in vpu_notify_eos() and vpu_notify_source_change(), to queue V4L2
events to the file handle ; and
- through the driver to access the v4l2_fh.m2m_ctx pointer.
The v4l2_fh.m2m_ctx pointer is not touched by v4l2_fh_del() and
v4l2_fh_exit(). It is set to NULL by the driver when closing the file
handle, in vpu_v4l2_close().
The vpu_notify_eos() and vpu_notify_source_change() functions are called
in vpu_set_last_buffer_dequeued() and vdec_handle_resolution_change()
respectively, only if the v4l2_fh.m2m_ctx pointer is not NULL. There is
therefore a guarantee that no new event will be queued to the v4l2_fh
after vpu_v4l2_close() destroys the m2m_ctx.
The vpu_notify_eos() function is also called from vpu_vb2_buf_finish(),
which is guaranteed to be called for all queued buffers when
vpu_v4l2_close() calls v4l2_m2m_ctx_release(), and will not be called
later.
It is therefore safe to assume that the driver will not touch the
v4l2_fh, except to check the m2m_ctx pointer, after vpu_v4l2_close()
destroys the m2m_ctx. We can safely delete and cleanup the v4l2_fh
synchronously in vpu_v4l2_close().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Ming Qian <ming.qian@oss.nxp.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ivtv driver has a structure named ivtv_open_id that models an open
file handle for the device. It embeds a v4l2_fh instance for file
handles that correspond to a V4L2 video device, and stores a pointer to
that v4l2_fh in struct ivtv_stream to identify which open file handle
owns a particular stream.
In addition to video devices, streams can be owned by ALSA PCM devices.
Those devices do not make use of the v4l2_fh instance for obvious
reasons, but the snd_ivtv_pcm_capture_open() function still initializes
a "fake" v4l2_fh for the sole purpose of using it as an open file handle
identifier. The v4l2_fh is not properly destroyed when the ALSA PCM
device is closed, leading to possible resource leaks.
Fortunately, the v4l2_fh instance pointed to by ivtv_stream is not
accessed, only the pointer value is used for comparison. Replace it with
a pointer to the ivtv_open_id structure that embeds the v4l2_fh, and
don't initialize the v4l2_fh for ALSA PCM devices.
The Device Under Test should always be the local system.
While the Rx test gets this right the Tx test is sending
from remote to local. So Tx of DMABUF memory happens on remote.
These tests never run in NIPA since we don't have a compatible
device so we haven't caught this.
Reviewed-by: Joe Damato <joe@dama.to> Reviewed-by: Mina Almasry <almasrymina@google.com> Acked-by: Stanislav Fomichev <sdf@fomichev.me> Link: https://patch.msgid.link/20250811231334.561137-6-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some kfd ioctls may not be available depending on the kernel version the
user is running, as such we need to report -ENOTTY so userland can
determine the cause of the ioctl failure.
Signed-off-by: Geoffrey McRae <geoffrey.mcrae@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The register REG_SYS_CFG1 is used to determine chip basic information
as arguments of following flows, such as download firmware and load PHY
parameters, so driver read the value early (before power-on).
However, the direct IO is disallowed before power-on, or it causes wrong
values, which driver recognizes a chip as a wrong type RF_1T1R, but
actually RF_2T2R, causing driver warns:
rtw88_8822cs mmc1:0001:1: unsupported rf path (1)
Fix it by using indirect IO before power-on.
Reported-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com> Closes: https://lore.kernel.org/linux-wireless/699C22B4-A3E3-4206-97D0-22AB3348EBF6@gmail.com/T/#t Suggested-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Tested-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250724004815.7043-1-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When driver receives new or unknown C2H events, it print out messages
repeatedly once events are received, like
rtw89_8922ae 0000:81:00.0: PHY c2h class 2 not support
To avoid the thousands of messages, use rtw89_info_once() instead. Also,
print out class/func for unknown (undefined) class.
Reported-by: Sean Anderson <sean.anderson@linux.dev> Closes: https://lore.kernel.org/linux-wireless/20250729204437.164320-1-sean.anderson@linux.dev/ Reviewed-by: Sean Anderson <sean.anderson@linux.dev> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250804012234.8913-2-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The get_next_frame() function in psock_tpacket.c was missing a return
statement in its default switch case, leading to a compiler warning.
This was caused by a `bug_on(1)` call, which is defined as an
`assert()`, being compiled out because NDEBUG is defined during the
build.
Instead of adding a `return NULL;` which would silently hide the error
and could lead to crashes later, this change restores the original
author's intent. By adding `#undef NDEBUG` before including <assert.h>,
we ensure the assertion is active and will cause the test to abort if
this unreachable code is ever executed.
The `__WORDSIZE` macro, defined in the non-standard `<bits/wordsize.h>`
header, is a GNU extension and not universally available with all
toolchains, such as Clang when used with musl libc.
This can lead to build failures in environments where this header is
missing.
The intention of the code is to determine the bit width of a C `long`.
Replace the non-portable `__WORDSIZE` with the standard and portable
`sizeof(long) * 8` expression to achieve the same result.
This change also removes the inclusion of the now-unused
`<bits/wordsize.h>` header.
Signed-off-by: Wake Liu <wakel@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Introduce high-res OLED panel for the Dell XPS 9345
These timings were selected based on Alex Vinarkskis' commit,
(6b3815c6815f07acc7eeffa8ae734d1a1c0ee817) for the LQ134N1
and seem to work fine for the high-res OLED panel on the 9345.
Signed-off-by: Christopher Orr <chris.orr@gmail.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/aJKvm3SlhLGHW4qn@jander Signed-off-by: Sasha Levin <sashal@kernel.org>
Always set the RMDevidCheckIgnore registry key for GSP-RM so that it
will continue support newer variants of already supported GPUs.
GSP-RM maintains an internal list of PCI IDs of GPUs that it supports,
and checks if the current GPU is on this list. While the actual GPU
architecture (as specified in the BOOT_0/BOOT_42 registers) determines
how to enable the GPU, the PCI ID is used for the product name, e.g.
"NVIDIA GeForce RTX 5090".
Unfortunately, if there is no match, GSP-RM will refuse to initialize,
even if the device is fully supported. Nouveau will get an error
return code, but by then it's too late. This behavior may be corrected
in a future version of GSP-RM, but that does not help Nouveau today.
Fortunately, GSP-RM supports an undocumented registry key that tells it
to ignore the mismatch. In such cases, the product name returned will
be a blank string, but otherwise GSP-RM will continue.
Unlike Nvidia's proprietary driver, Nouveau cannot update to newer
firmware versions to keep up with every new hardware release. Instead,
we can permanently set this registry key, and GSP-RM will continue
to function the same with known hardware.
RDC PCI to PCIe bridges, present on Vortex86DX3 and Vortex86EX2 SoCs, do
not support MSIs. If enabled, interrupts generated by PCIe devices never
reach the processor.
I have contacted the manufacturer (DM&P) and they confirmed that PCI MSIs
need to be disabled for them.
Use DRM's shadow-plane helper to map and access the GEM object's buffer
within kernel address space. Encapsulates the vmap logic in the GEM-DMA
helpers.
The sharp-memory driver currently reads the vaddr field from the GME
buffer object directly. This only works because GEM code 'automagically'
sets vaddr.
Shadow-plane helpers perform the same steps, but with correct abstraction
behind drm_gem_vmap(). The shadow-plane state provides the buffer address
in kernel address space and the format-conversion state.
While we do need at least 3.6 for kernel-doc to work, and at least
3.7 for it to output functions and structs with parameters at the
right order, let the python binary be compatible with legacy
versions.
The rationale is that the Kernel build nowadays calls kernel-doc
with -none on some places. Better not to bail out when older
versions are found.
With that, potentially this will run with python 2.7 and 3.2+,
according with vermin:
The minimal version I could check was version 3.4
(using anaconda). Anaconda doesn't support 3.2 or 3.3
anymore, and 3.2 doesn't even compile (I tested compiling
Python 3.2 on Fedora 42 and on Fedora 32 - no show).
With 3.4, the script didn't crash and emitted the right warning:
$ conda create -n py34 python=3.4
$ conda activate py34
python --version
Python 3.4.5
$ python ./scripts/kernel-doc --none include/media
Error: Python 3.6 or later is required by kernel-doc
$ conda deactivate
$ python --version
Python 3.13.5
$ python ./scripts/kernel-doc --none include/media
(no warnings and script ran properly)
Supporting 2.7 is out of scope, as it is EOL for 5 years, and
changing shebang to point to "python" instead of "python3"
would have a wider impact.
I did some extra checks about the differences from 3.2 and
3.4, and didn't find anything that would cause troubles:
For non-leaf paging structures we end up selecting a random index
between [0, 3], depending on the first user if the page-table is shared,
since non-leaf structures only have two bits in the HW for encoding the
PAT index, and here we are just passing along the full user provided
index, which can be an index as large as ~31 on xe2+. The user provided
index is meant for the leaf node, which maps the actual BO pages where
we have more PAT bits, and not the non-leaf nodes which are only mapping
other paging structures, and so only needs a minimal PAT index range.
Also the chosen index might need to consider how the driver mapped the
paging structures on the host side, like wc vs wb, which is separate
from the user provided index.
With that move the PDE PAT index selection under driver control. For now
just use a coherent index on platforms with page-tables that are cached
on host side, and incoherent otherwise. Using a coherent index could
potentially be expensive, and would be overkill if we know the page-table
is always uncached on host side.
v2 (Stuart):
- Add some documentation and split into separate helper.
BSpec: 59510 Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Stuart Summers <stuart.summers@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Stuart Summers <stuart.summers@intel.com> Link: https://lore.kernel.org/r/20250808103455.462424-2-matthew.auld@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Customer reported an issue that OS starts and stops device multiple times
during driver installation. Frequently disabling and enabling OTG may
prevent OTG from being safely disabled and cause incorrect configuration
upon the next enablement.
[How]
Add a wait until OTG_CURRENT_MASTER_EN_STATE is cleared as a short term
solution.
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: TungYu Lu <tungyu.lu@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
User queues are disabled before GEM objects are released
(protecting against user app crashes).
No races with PCI hot-unplug (because drm_dev_enter prevents cleanup
if iewdevice is being removed).
Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY&HOW]
The user closed the lid while the system was powering on and opened it
again before the “apply_seamless_boot_optimization” was set to false,
resulting in the eDP remaining blank.
Reset the “apply_seamless_boot_optimization” to false when dpms off.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Danny Wang <Danny.Wang@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SND_JACK_AVOUT is a more specific jack type for HDMI and DisplayPort.
Updatae the MediaTek drivers to use such jack type, allowing system to
determine the device type based on jack event.
Since version 0x105, the keyword 'init' was introduced into the profile,
which is used for chip initialization, particularly to store common
settings for other non-initialization profiles.
snprintf() returns the number of characters that *would* have been
written, which can overestimate how much you actually wrote to the
buffer in case of truncation. That leads to 'data += this' advancing
the pointer past the end of the buffer and size going negative.
Switching to scnprintf() prevents potential buffer overflows and ensures
consistent behavior when building the output string.
Previously, the LMTT directory pointer was only programmed for primary GT
within a tile. However, to ensure correct Local Memory access by VFs,
the LMTT configuration must be programmed on all GTs within the tile.
Lets program the LMTT directory pointer on every GT of the tile
to guarantee proper LMEM access across all GTs on VFs.
HSD: 18042797646
Bspec: 67468 Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Reviewed-by: Stuart Summers <stuart.summers@intel.com> Link: https://lore.kernel.org/r/20250805091850.1508240-1-piotr.piorkowski@intel.com Signed-off-by: Michał Winiarski <michal.winiarski@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Acquire jpeg_pg_lock before changes to jpeg power state
and release it after power off from idle work handler.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The suspend and resume callbacks for pm and runtime pm should be same.
During suspending, it needs to stop all hardware contexts first. And
the hardware contexts will be restarted after the device is resumed.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org> Reviewed-by: Maciej Falkowski <maciej.falkowski@linux.intel.com> Signed-off-by: Lizhi Hou <lizhi.hou@amd.com> Link: https://lore.kernel.org/r/20250803191450.1568851-1-lizhi.hou@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Cached metrics data validity is 1ms on arcturus. It's not reasonable for
any client to query gpu_metrics at a faster rate and constantly
interrupt PMFW.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Asad Kamal <asad.kamal@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cached metrics data validity is 1ms on aldebaran. It's not reasonable
for any client to query gpu_metrics at a faster rate and constantly
interrupt PMFW.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Asad Kamal <asad.kamal@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The reason some high-resolution monitors fail to display properly
is that this platform does not support sufficiently high DPP and
DISP clock frequencies
[How]
Update DISP and DPP clocks from the smu clock table then DML can
filter these mode if not support.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Accessing DC from amdgpu_dm is usually preceded by acquisition of
dc_lock mutex. Most of the DC API that DM calls are under a DC lock.
However, there are a few that are not. Some DC API called from interrupt
context end up sending DMUB commands via a DC API, while other threads were
using DMUB. This was apparent from a race between calls for setting idle
optimization enable/disable and the DC API to set vmin/vmax.
Offload the call to dc_stream_adjust_vmin_vmax() to a thread instead
of directly calling them from the interrupt handler such that it waits
for dc_lock.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move amdgpu_device_health_check into amdgpu_device_gpu_recover to
ensure that if the device is present can be checked before reset
The reason is:
1.During the dpc event, the device where the dpc event occurs is not
present on the bus
2.When both dpc event and ATHUB event occur simultaneously,the dpc thread
holds the reset domain lock when detecting error,and the gpu recover thread
acquires the hive lock.The device is simultaneously in the states of
amdgpu_ras_in_recovery and occurs_dpc,so gpu recover thread will not go to
amdgpu_device_health_check.It waits for the reset domain lock held by the
dpc thread, but dpc thread has not released the reset domain lock.In the dpc
callback slot_reset,to obtain the hive lock, the hive lock is held by the
gpu recover thread at this time.So a deadlock occurred
Signed-off-by: Ce Sun <cesun102@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Try to ensure poison creation handle is completed in time
to set device rma value.
Signed-off-by: Ce Sun <cesun102@amd.com> Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The variable `pm_suspend_target_state` is conditionally defined only when
`CONFIG_SUSPEND` is enabled (see `include/linux/suspend.h`). Directly
referencing it without guarding by `#ifdef CONFIG_SUSPEND` causes build
failures when suspend functionality is disabled (e.g., `CONFIG_SUSPEND=n`).
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Perry Yuan <perry.yuan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PF's restart worker shouldn't attempt to resume the device on
its own, since its goal is to finish PF and VFs reprovisioning on
the recently reset GuC. Take extra RPM reference while scheduling
a work and release it from the worker or when we cancel a work.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com> Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com> Link: https://lore.kernel.org/r/20250801142822.180530-4-michal.wajdeczko@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
I saw an oops in xe_gem_fault when running the xe-fast-feedback
testlist against the realtime kernel without debug options enabled.
The panic happens after core_hotunplug unbind-rebind finishes.
Presumably what happens is that a process mmaps, unlocks because
of the FAULT_FLAG_RETRY_NOWAIT logic, has no process memory left,
causing ttm_bo_vm_dummy_page() to return VM_FAULT_NOPAGE, since
there was nothing left to populate, and then oopses in
"mem_type_is_vram(tbo->resource->mem_type)" because tbo->resource
is NULL.
It's convoluted, but fits the data and explains the oops after
the test exits.
The GuC load process will abort if certain status codes (which are
indicative of a fatal error) are reported. Otherwise, it keeps waiting
until the 'success' code is returned. New error codes have been added
in recent GuC releases, so add support for aborting on those as well.
v2: Shuffle HWCONFIG_START to the front of the switch to keep the
ordering as per the enum define for clarity (review feedback by
Jonathan). Also add a description for the basic 'invalid init data'
code which was missing.
[WHY]
Last LT automation update can cause crash by referencing current_state and
calling into dc_update_planes_and_stream which may clobber current_state.
[HOW]
Cache relevant stream pointers and iterate through them instead of relying
on the current_state.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Michael Strauss <michael.strauss@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why & how]
Header misalignment in struct dmub_cmd_replay_copy_settings_data and
struct dmub_alpm_auxless_data causes incorrect data read between driver
and dmub.
Fix the misalignment and ensure that everything is aligned to 4-byte
boundaries.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
In the worst case, AUX intra-hop done can take hundreds of milliseconds as
each retimer in a link might have to wait a full AUX_RD_INTERVAL to send
LT abort downstream.
[HOW]
Wait 300ms for each retimer in a link to allow time to propagate a LT abort
without infinitely waiting on intra-hop done.
For no-retimer case, keep the max duration at 10ms.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Michael Strauss <michael.strauss@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
If symclk RCO is enabled, stream encoder may not be receiving an ungated
clock by the time we attempt to set stream attributes when setting dpms
on. Since the clock is gated, register writes to the stream encoder fail.
[HOW]
Move set_stream_attribute call into enable_stream, just after the point
where symclk32_se is ungated.
Logically there is no need to set stream attributes as early as is
currently done in link_set_dpms_on, so this should have no impact beyond
the RCO fix.
Reviewed-by: Ovidiu (Ovi) Bunea <ovidiu.bunea@amd.com> Signed-off-by: Michael Strauss <michael.strauss@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Log an error when vcn sram load fails in indirect mode
and return the same error value.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
When transitioning between topologies such as multi-display to single
display ODM 2:1, pipes might not be freed before use.
[How]
In dc_commit_streams, commit an additional, minimal transition if
original transition is not seamless to ensure pipes are freed.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Clay King <clayking@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
timing_adjust_pending is used to defer certain programming sequences
when OTG timing is about to be changed, like with VRR. Insufficient
checking for timing change in this case caused a regression which
reduces PSR Replay residency.
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Robin Chen <robin.chen@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why & How]
Tiled command rect dimensions is 1 based, do rect_x/y - 1 internally
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Ostrowski Rafal <rostrows@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While we expect config directory names to match PCI device name,
currently we are only scanning provided names for domain, bus,
device and function numbers, without checking their format.
This would pass slightly broken entries like:
To avoid such mistakes, check if the name provided exactly matches
the canonical PCI device address format, which we recreated from
the parsed BDF data. Also simplify scanf format as it can't really
catch all formatting errors.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://lore.kernel.org/r/20250722141059.30707-3-michal.wajdeczko@intel.com Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As pm_runtime_force_suspend() will force the device state to suspend,
the driver needs to ensure no IRQ handlers are currently running. If not
those handlers may find they are now running on suspended hardware
despite holding a PM runtime reference. disable_irq() will sync any
currently running handlers, so move the IRQ disabling to cover the whole
of the forced suspend state to avoid such race conditions.
When an MFD device is added, a platform_device is allocated. If this
device is linked to a DT description, the corresponding OF node is linked
to the new platform device but the OF node's refcount isn't incremented.
As of_node_put() is called during the platform device release, it leads
to a refcount underflow.
Call of_node_get() to increment the OF node's refcount when the node is
linked to the newly created platform device.
After discussion with the devicetree maintainers we agreed to not extend
lists with the generic compatible "apple,smc" anymore [1]. Use
"apple,t8103-smc" as base compatible as it is the SoC the driver and
bindings were written for.
We observed the initial probe of the da9063 failing in
da9063_get_device_type in about 30% of boots on a Xilinx ZynqMP based
board. The problem originates in da9063_i2c_blockreg_read, which uses
a single bus transaction to turn the register page and then read a
register. On the bus, this should translate to a write to register 0,
followed by a read to the target register, separated by a repeated
start. However, we found that after the write to register 0, the
controller sometimes continues directly with the register address of
the read request, without sending the chip address or a repeated start
in between, which makes the read request invalid.
To fix this, separate turning the page and reading the register into
two separate transactions. This brings the initialization code in line
with the rest of the driver, which uses register maps (which to my
knowledge do not use repeated starts after turning the page). This has
been included in our kernel for several months and was recently
included in a shipped product. For us, it reliably fixes the issue,
and we have not observed any new issues.
While the underlying problem is probably with the i2c controller or
its driver, I still propose a change here in the interest of
robustness: First, I'm not sure this issue can be fixed on the
controller side, since there are other issues related to repeated
start which can't (AR# 60695, AR# 61664). Second, similar problems
might exist with other controllers.
clang-21 warns about one uninitialized variable getting dereferenced
in madera_dev_init:
drivers/mfd/madera-core.c:739:10: error: variable 'mfd_devs' is uninitialized when used here [-Werror,-Wuninitialized]
739 | mfd_devs, n_devs,
| ^~~~~~~~
drivers/mfd/madera-core.c:459:33: note: initialize the variable 'mfd_devs' to silence this warning
459 | const struct mfd_cell *mfd_devs;
| ^
| = NULL
The code is actually correct here because n_devs is only nonzero
when mfd_devs is a valid pointer, but this is impossible for the
compiler to see reliably.
Change the logic to check for the pointer as well, to make this easier
for the compiler to follow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20250807071932.4085458-1-arnd@kernel.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The QIXIS FPGA found on Layerscape boards such as LX2160AQDS, LS1028AQDS
etc deals with power-on-reset timing, muxing etc. Use the simple-mfd-i2c
as its core driver by adding its compatible string (already found in
some dt files). By using the simple-mfd-i2c driver, any child device
will have access to the i2c regmap created by it.
When we are successful in using cpufreq min/max limits,
skip setting the raw MSR limits entirely.
This is necessary to avoid undoing any modification that
the cpufreq driver makes to our sysfs request.
eg. intel_pstate may take our request for a limit
that is valid according to HWP.CAP.MIN/MAX and clip
it to be within the range available in PLATFORM_INFO.
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fopen_or_die() function was previously hardcoded
to open files in read-only mode ("r"), ignoring the
mode parameter passed to it. This patch corrects
fopen_or_die() to use the provided mode argument,
allowing for flexible file access as intended.
Additionally, the call to fopen_or_die() in
err_on_hypervisor() incorrectly used the mode
"ro", which is not a valid fopen mode. This is
fixed to use the correct "r" mode.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pmt_telemdir_sort() comparison function was returning a boolean
value (0 or 1) instead of the required negative, zero, or positive
value for proper sorting. This caused unpredictable and incorrect
ordering of telemetry directories named telem0, telem1, ..., telemN.
Update the comparison logic to return -1, 0, or 1 based on the
numerical value extracted from the directory name, ensuring correct
numerical ordering when using scandir.
This change improves stability and correctness when iterating PMT
telemetry directories.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
bpf_cookie can fail on perf_event_open(), when it runs after the task_work
selftest. The task_work test causes perf to lower
sysctl_perf_event_sample_rate, and bpf_cookie uses sample_freq,
which is validated against that sysctl. As a result,
perf_event_open() rejects the attr if the (now tighter) limit is
exceeded.
>From perf_event_open():
if (attr.freq) {
if (attr.sample_freq > sysctl_perf_event_sample_rate)
return -EINVAL;
} else {
if (attr.sample_period & (1ULL << 63))
return -EINVAL;
}
Switch bpf_cookie to use sample_period, which is not checked against
sysctl_perf_event_sample_rate.
Fix incorrect size parameter passed to cpuidle_state_write_file() in
cpuidle_state_disable().
The function was incorrectly using sizeof(disable) which returns the
size of the unsigned int variable (4 bytes) instead of the actual
length of the string stored in the 'value' buffer.
Since 'value' is populated with snprintf() to contain the string
representation of the disable value, we should use the length
returned by snprintf() to get the correct string length for
writing to the sysfs file.
This ensures the correct number of bytes is written to the cpuidle
state disable file in sysfs.
The Dell OptiPlex 7040 supports the legacy SMM interface for reading
sensors and performing fan control. Whitelist this machine so that
this driver loads automatically.
It turns out the second fan on the Dell Precision 490 does not
really support I8K_FAN_TURBO. Setting the fan state to 3 enables
automatic fan control, just like on the other two fans.
The reason why this was misinterpreted as turbo mode was that
the second fan normally spins faster in automatic mode than
in the previous fan states. Yet when in state 3, the fan speed
reacts to heat exposure, exposing the automatic mode setting.
Some motherboards require more time to acquire the ACPI mutex,
causing "Failed to acquire mutex" messages to appear in the kernel log.
Increase the timeout from 500ms to 800ms to accommodate these cases.
If uprobe handler changes instruction pointer we still execute single
step) or emulate the original instruction and increment the (new) ip
with its length.
This makes the new instruction pointer bogus and application will
likely crash on illegal instruction execution.
If user decided to take execution elsewhere, it makes little sense
to execute the original instruction, so let's skip it.
"""
A host requests an explicit persistent connection ... by specifying a
non-zero Keep Alive Timer value in the Connect command.
"""
As such if we are starting a persistent connection to a discovery
controller and the KATO is currently 0 we need to update KATO to a non
zero value to avoid continuous timeouts on the target.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible for drivers to generate xdp packets with data residing
entirely in fragments. To keep parsing headers using direct packet
access, call bpf_xdp_pull_data() to pull headers into the linear data
area.
It is possible for bpf_xdp_adjust_tail() to free all fragments. The
kfunc currently clears the XDP_FLAGS_HAS_FRAGS bit, but not
XDP_FLAGS_FRAGS_PF_MEMALLOC. So far, this has not caused a issue when
building sk_buff from xdp_buff since all readers of xdp_buff->flags
use the flag only when there are fragments. Clear the
XDP_FLAGS_FRAGS_PF_MEMALLOC bit as well to make the flags correct.
Signed-off-by: Amery Hung <ameryhung@gmail.com> Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://patch.msgid.link/20250922233356.3356453-2-ameryhung@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In the __arch_prepare_bpf_trampoline() function, retval_off is only
meaningful when save_ret is true, so the current logic is correct.
However, in the original logic, retval_off is only initialized under
certain conditions; for example, in the fmod_ret logic, the compiler is
not aware that the flags of the fmod_ret program (prog) have set
BPF_TRAMP_F_CALL_ORIG, which results in an uninitialized symbol
compilation warning.
So initialize retval_off unconditionally to fix it.
Root cause is that queue_usage_counter is grabbed with rq_qos_mutex
held in blkg_conf_prep(), while queue should be freezed before
rq_qos_mutex from other context.
The blk_queue_enter() from blkg_conf_prep() is used to protect against
policy deactivation, which is already protected with blkcg_mutex, hence
convert blk_queue_enter() to blkcg_mutex to fix this problem. Meanwhile,
consider that blkcg_mutex is held after queue is freezed from policy
deactivation, also convert blkg_alloc() to use GFP_NOIO.
Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
During normal operation the timers are reprogrammed including an
interrupt acknowledgement. This has no effect as the whole timer
is setup from scratch afterwards. Especially in an interrupt this
has already been done by rttm_timer_interrupt().
Change the behaviour as follows:
- Use rttm_disable_timer() during reprogramming
- Keep rttm_stop_timer() for all other use cases.
Downstream has already tested and confirmed a patch. See
https://github.com/openwrt/openwrt/pull/19468
https://forum.openwrt.org/t/support-for-rtl838x-based-managed-switches/57875/3788
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Tested-by: Stephen Howell <howels@allthatwemight.be> Tested-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20250804080328.2609287-4-markus.stockhausen@gmx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The OpenWrt distribution has switched from kernel longterm 6.6 to
6.12. Reports show that devices with the Realtek Otto switch platform
die during operation and are rebooted by the watchdog. Sorting out
other possible reasons the Otto timer is to blame. The platform
currently consists of 4 targets with different hardware revisions.
It is not 100% clear which devices and revisions are affected.
Analysis shows:
A more aggressive sched/deadline handling leads to more timer starts
with small intervals. This increases the bug chances. See
https://marc.info/?l=linux-kernel&m=175276556023276&w=2
Focusing on the real issue a hardware limitation on some devices was
found. There is a minimal chance that a timer ends without firing an
interrupt if it is reprogrammed within the 5us before its expiration
time. Work around this issue by introducing a bounce() function. It
restarts the timer directly before the normal restart functions as
follows:
- Stop timer
- Restart timer with a slow frequency.
- Target time will be >5us
- The subsequent normal restart is outside the critical window
Downstream has already tested and confirmed a patch. See
https://github.com/openwrt/openwrt/pull/19468
https://forum.openwrt.org/t/support-for-rtl838x-based-managed-switches/57875/3788
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Tested-by: Stephen Howell <howels@allthatwemight.be> Tested-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20250804080328.2609287-2-markus.stockhausen@gmx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The Microsoft Serial Port Console Redirection (SPCR) specification
revision 1.09 comprises additional field: Precise Baud Rate [1].
It is used to describe non-traditional baud rates (such as those
used by high-speed UARTs).
It contains a specific non-zero baud rate which overrides the value
of the Configured Baud Rate field. If this field is zero or not
present, Configured Baud Rate is used.
Some ublk selftests have strange behavior when fio is not installed.
While most tests behave correctly (run if they don't need fio, or skip
if they need fio), the following tests have different behavior:
- test_null_01, test_null_02, test_generic_01, test_generic_02, and
test_generic_12 try to run fio without checking if it exists first,
and fail on any failure of the fio command (including "fio command
not found"). So these tests fail when they should skip.
- test_stress_05 runs fio without checking if it exists first, but
doesn't fail on fio command failure. This test passes, but that pass
is misleading as the test doesn't do anything useful without fio
installed. So this test passes when it should skip.
Fix these issues by adding _have_program fio checks to the top of all of
these tests.
Signed-off-by: Uday Shankar <ushankar@purestorage.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
