According to 802.1AE standard, when ES and SC flags in TCI are zero,
used SCI should be the current active SC_RX. Current code uses the
header MAC address. Without this patch, when ES flag is 0 (using a
bridge or switch), header MAC will not fit the SCI and MACSec frames
will be discarted.
In order to test this issue, MACsec link should be stablished between
two interfaces, setting SC and ES flags to zero and a port identifier
different than one. For example, using ip macsec tools:
ip link add link $ETH0 macsec0 type macsec port 11 send_sci off
end_station off
ip macsec add macsec0 tx sa 0 pn 2 on key 01 $ETH1_KEY
ip macsec add macsec0 rx port 11 address $ETH1_MAC
ip macsec add macsec0 rx port 11 address $ETH1_MAC sa 0 pn 2 on key 02
ip link set dev macsec0 up
ip link add link $ETH1 macsec1 type macsec port 11 send_sci off
end_station off
ip macsec add macsec1 tx sa 0 pn 2 on key 01 $ETH0_KEY
ip macsec add macsec1 rx port 11 address $ETH0_MAC
ip macsec add macsec1 rx port 11 address $ETH0_MAC sa 0 pn 2 on key 02
ip link set dev macsec1 up
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Co-developed-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de> Signed-off-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de> Signed-off-by: Carlos Fernandez <carlos.fernandez@technica-engineering.de> Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
sk->sk_prot->sock_is_readable is a valid function pointer when sk resides
in a sockmap. After the last sk_psock_put() (which usually happens when
socket is removed from sockmap), sk->sk_prot gets restored and
sk->sk_prot->sock_is_readable becomes NULL.
This makes sk_is_readable() racy, if the value of sk->sk_prot is reloaded
after the initial check. Which in turn may lead to a null pointer
dereference.
Ensure the function pointer does not turn NULL after the check.
Fixes: 8934ce2fd081 ("bpf: sockmap redirect ingress support") Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Michal Luczaj <mhal@rbox.co> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20250609-skisreadable-toctou-v1-1-d0dfb2d62c37@rbox.co Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With nosmp in cmdline, other CPUs are not brought up, leaving
their cpc_desc_ptr NULL. CPU0's iteration via for_each_possible_cpu()
dereferences these NULL pointers, causing panic.
Panic backtrace:
[ 0.401123] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000b8
...
[ 0.403255] [<ffffffff809a5818>] cppc_allow_fast_switch+0x6a/0xd4
...
Kernel panic - not syncing: Attempted to kill init!
Fixes: 3cc30dd00a58 ("cpufreq: CPPC: Enable fast_switch") Reported-by: Xu Lu <luxu.kernel@bytedance.com> Signed-off-by: Yunhui Cui <cuiyunhui@bytedance.com> Link: https://patch.msgid.link/20250604023036.99553-1-cuiyunhui@bytedance.com
[ rjw: New subject ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a VFLR interrupt is received during a VF reset initiated from a
different source, the VFLR may be not fully handled. This can
leave the VF in an undefined state.
To address this, set the I40E_VFLR_EVENT_PENDING bit again during VFLR
handling if the reset is not yet complete. This ensures the driver
will properly complete the VF reset in such scenarios.
Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF") Signed-off-by: Robert Malz <robert.malz@canonical.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function i40e_vc_reset_vf attempts, up to 20 times, to handle a
VF reset request, using the return value of i40e_reset_vf as an indicator
of whether the reset was successfully triggered. Currently, i40e_reset_vf
always returns true, which causes new reset requests to be ignored if a
different VF reset is already in progress.
This patch updates the return value of i40e_reset_vf to reflect when
another VF reset is in progress, allowing the caller to properly use
the retry mechanism.
Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF") Signed-off-by: Robert Malz <robert.malz@canonical.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 1017560164b6 ("drm/meson: use unsigned long long / Hz for
frequency types") attempts to resolve video playback using 59.94Hz.
using YUV420 by changing the clock calculation to use
Hz instead of kHz (thus yielding more precision).
The basic calculation itself is correct, however the comparisions in
meson_vclk_vic_supported_freq() and meson_vclk_setup() don't work
anymore for 59.94Hz modes (using the freq * 1000 / 1001 logic). For
example, drm/edid specifies a 593407kHz clock for 3840x2160@59.94Hz.
With the mentioend commit we convert this to Hz. Then meson_vclk
tries to find a matchig "params" entry (as the clock setup code
currently only supports specific frequencies) by taking the venc_freq
from the params and calculating the "alt frequency" (used for the
59.94Hz modes) from it, which is:
(594000000Hz * 1000) / 1001 = 593406593Hz
Similar calculation is applied to the phy_freq (TMDS clock), which is 10
times the pixel clock.
Implement a new meson_vclk_freqs_are_matching_param() function whose
purpose is to compare if the requested and calculated frequencies. They
may not match exactly (for the reasons mentioned above). Allow the
clocks to deviate slightly to make the 59.94Hz modes again.
Fixes: 1017560164b6 ("drm/meson: use unsigned long long / Hz for frequency types") Reported-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20250609202751.962208-1-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
meson_vclk_vic_supported_freq() has a debug print which includes the
pixel freq. However, within the whole function the pixel freq is
irrelevant, other than checking the end of the params array. Switch to
printing the vclk_freq which is being compared / matched against the
inputs to the function to avoid confusion when analyzing error reports
from users.
Fixes: e5fab2ec9ca4 ("drm/meson: vclk: add support for YUV420 setup") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20250606221031.3419353-1-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The "phy" and "vclk" frequency labels were swapped, making it more
difficult to debug driver errors. Swap the label order to make them
match with the actual frequencies printed to correct this.
Fixes: e5fab2ec9ca4 ("drm/meson: vclk: add support for YUV420 setup") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20250606203729.3311592-1-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The video clock requested by the drm framework is 593407kHz. This is
passed by meson_encoder_hdmi_atomic_enable() to
meson_encoder_hdmi_set_vclk() and the following formula is applied:
- the frequency is halved (which would be 296703.5kHz) and rounded down
to the next full integer, which is 296703kHz
- TMDS clock is calculated (296703kHz * 10)
- video encoder clock is calculated - this needs to match a table from
meson_vclk.c and so it doubles the previously halved value again
(resulting in 593406kHz)
- meson_vclk_setup() can't find (either directly, or by deriving it from
594000kHz * 1000 / 1001 and rounding to the closest integer value -
which is 593407kHz as originally requested by the drm framework) a
matching clock in it's internal table and errors out with "invalid
HDMI vclk freq"
Fix the division precision by switching the whole meson driver to use
unsigned long long (64-bit) Hz values for clock frequencies instead of
unsigned int (32-bit) kHz to fix the rouding error.
The user space calls mmap() to map VAS window paste address
and the kernel returns the complete mapped page for each
window. So return -EINVAL if non-zero is passed for offset
parameter to mmap().
See Documentation/arch/powerpc/vas-api.rst for mmap()
restrictions.
Co-developed-by: Jonathan Greental <yonatan02greental@gmail.com> Signed-off-by: Jonathan Greental <yonatan02greental@gmail.com> Reported-by: Jonathan Greental <yonatan02greental@gmail.com> Fixes: dda44eb29c23 ("powerpc/vas: Add VAS user space API") Signed-off-by: Haren Myneni <haren@linux.ibm.com> Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com> Link: https://patch.msgid.link/20250610021227.361980-2-maddy@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
memtrace mmap issue has an out of bounds issue. This patch fixes the by
checking that the requested mapping region size should stay within the
allocated region size.
SFQ has an assumption of always being able to queue at least one packet.
However, after the blamed commit, sch->q.len can be inflated by packets
in sch->gso_skb, and an enqueue() on an empty SFQ qdisc can be followed
by an immediate drop.
Fix sfq_drop() to properly clear q->tail in this situation.
Tested:
ip netns add lb
ip link add dev to-lb type veth peer name in-lb netns lb
ethtool -K to-lb tso off # force qdisc to requeue gso_skb
ip netns exec lb ethtool -K in-lb gro on # enable NAPI
ip link set dev to-lb up
ip -netns lb link set dev in-lb up
ip addr add dev to-lb 192.168.20.1/24
ip -netns lb addr add dev in-lb 192.168.20.2/24
tc qdisc replace dev to-lb root sfq limit 100
scsi_host_put() is not required when shost is NULL, so jumping to the
correct label avoids unnecessary operations. These functions previously
jumped to the wrong goto label (put_host), which did not match the
intended cleanup logic.
Use the correct exit labels (exit_new_fnode, exit_del_fnode, etc.) to
ensure proper error handling. Also remove the unused put_host label
under iscsi_new_flashnode() as it is no longer needed.
No functional changes beyond accurate error path correction.
Fixes: c6a4bb2ef596 ("[SCSI] scsi_transport_iscsi: Add flash node mgmt support") Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Link: https://lore.kernel.org/r/20250530193012.3312911-1-alok.a.tiwari@oracle.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the last transfer of a SPI message has the cs_change flag, the CS is kept
asserted after the message.
The next message can't use multi-mode because the CS will be briefly deasserted
before the first transfer.
Remove the early exit of the list_for_each_entry because the last transfer
actually needs to be always checked.
When the last transfer of a SPI message has the cs_change flag, the CS is kept
asserted after the message.
Multi-mode can't respect this as CS is deasserted by the hardware at the end of
the message.
Disable multi-mode when not applicable to the current message.
GCC_GCC_PCIE_HOT_RST is wrongly defined for WCN7850, causing kernel crash
on some specific platforms.
Since this register is divergent for WCN7850 and QCN9274, move it to
register table to allow different definitions. Then correct the register
address for WCN7850 to fix this issue.
Note IPQ5332 is not affected as it is not PCIe based device.
if ath11k_crypto_mode is invalid (not ATH11K_CRYPT_MODE_SW/ATH11K_CRYPT_MODE_HW),
ath11k_core_qmi_firmware_ready() will not undo some actions that was previously
started/configured. Do the validation as soon as possible in order to avoid
undoing actions in that case and also to fix the following smatch warning:
Commit b488c766442f ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855")
and commit c3b39553fc77 ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855")
call debugfs functions in mac ops. Those functions are no-ops if CONFIG_ATH11K_DEBUGFS is
not enabled, thus cause wrong status reported.
Move them to mac.c.
Besides, since WMI_REQUEST_RSSI_PER_CHAIN_STAT and WMI_REQUEST_VDEV_STAT stats could also
be requested via mac ops, process them directly in ath11k_update_stats_event().
Fixes: b488c766442f ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855") Fixes: c3b39553fc77 ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855") Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250220082448.31039-5-quic_bqiang@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath11k_debugfs_fw_stats_process() we wait until all events received.
In case there is no vdev started, this results in that below condition
would never get satisfied
Currently ath11k_debugfs_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever reason (
say ar->num_started_vdevs is 0 or firmware bug etc.) the following condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time when
firmware stats is requested again, even if everything is working fine, we will
fail due to the condition above will never be satisfied.
The same applies to num_bcn as well.
Change to use non-static counters so that we have a chance to clear them each
time firmware stats is requested. Currently only ath11k_fw_stats_request() and
ath11k_debugfs_fw_stats_request() are requesting firmware stats, so clear
counters there.
This is because, if for whatever reason ar->fw_stats_done is not set by
ath11k_update_stats_event(), ath11k_debugfs_fw_stats_request() won't yield
CPU before an up to 3s timeout.
Change to completion mechanism to avoid CPU burning.
Commit b35108a51cf7 ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
In ath10k_snoc_hif_stop() we skip disabling the IRQs in the crash
recovery flow, but we still unconditionally call enable again in
ath10k_snoc_hif_start().
We can't check the ATH10K_FLAG_CRASH_FLUSH bit since it is cleared
before hif_start() is called, so instead check the
ATH10K_SNOC_FLAG_RECOVERY flag and skip enabling the IRQs during crash
recovery.
This fixes unbalanced IRQ enable splats that happen after recovering from
a crash.
Fixes: 0e622f67e041 ("ath10k: add support for WCN3990 firmware crash recovery") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> Tested-by: Loic Poulain <loic.poulain@oss.qualcomm.com> Link: https://patch.msgid.link/20250318205043.1043148-1-caleb.connolly@linaro.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no disagreement that we should check both ptp->is_virtual_clock
and ptp->n_vclocks to check if the ptp virtual clock is in use.
However, when we acquire ptp->n_vclocks_mux to read ptp->n_vclocks in
ptp_vclock_in_use(), we observe a recursive lock in the call trace
starting from n_vclocks_store().
============================================
WARNING: possible recursive locking detected
6.15.0-rc6 #1 Not tainted
--------------------------------------------
syz.0.1540/13807 is trying to acquire lock: ffff888035a24868 (&ptp->n_vclocks_mux){+.+.}-{4:4}, at:
ptp_vclock_in_use drivers/ptp/ptp_private.h:103 [inline] ffff888035a24868 (&ptp->n_vclocks_mux){+.+.}-{4:4}, at:
ptp_clock_unregister+0x21/0x250 drivers/ptp/ptp_clock.c:415
but task is already holding lock: ffff888030704868 (&ptp->n_vclocks_mux){+.+.}-{4:4}, at:
n_vclocks_store+0xf1/0x6d0 drivers/ptp/ptp_sysfs.c:215
other info that might help us debug this:
Possible unsafe locking scenario:
The best way to solve this is to remove the logic that checks
ptp->n_vclocks in ptp_vclock_in_use().
The reason why this is appropriate is that any path that uses
ptp->n_vclocks must unconditionally check if ptp->n_vclocks is greater
than 0 before unregistering vclocks, and all functions are already
written this way. And in the function that uses ptp->n_vclocks, we
already get ptp->n_vclocks_mux before unregistering vclocks.
Therefore, we need to remove the redundant check for ptp->n_vclocks in
ptp_vclock_in_use() to prevent recursive locking.
Fixes: 73f37068d540 ("ptp: support ptp physical/virtual clocks conversion") Signed-off-by: Jeongjun Park <aha310510@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://patch.msgid.link/20250520160717.7350-1-aha310510@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When Linux sends out untagged traffic from a port, it will enter the CPU
port without any VLAN tag, even if the port is a member of a vlan
filtering bridge with a PVID egress untagged VLAN.
This makes the CPU port's PVID take effect, and the PVID's VLAN
table entry controls if the packet will be tagged on egress.
Since commit 45e9d59d3950 ("net: dsa: b53: do not allow to configure
VLAN 0") we remove bridged ports from VLAN 0 when joining or leaving a
VLAN aware bridge. But we also clear the untagged bit, causing untagged
traffic from the controller to become tagged with VID 0 (and priority
0).
Fix this by not touching the untagged map of VLAN 0. Additionally,
always keep the CPU port as a member, as the untag map is only effective
as long as there is at least one member, and we would remove it when
bridging all ports and leaving no standalone ports.
Since Linux (and the switch) treats VLAN 0 tagged traffic like untagged,
the actual impact of this is rather low, but this also prevented earlier
detection of the issue.
Fixes: 45e9d59d3950 ("net: dsa: b53: do not allow to configure VLAN 0") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://patch.msgid.link/20250602194914.1011890-1-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This uses a mutex to protect from concurrent access of mgmt_pending
list which can cause crashes like:
==================================================================
BUG: KASAN: slab-use-after-free in hci_sock_get_channel+0x60/0x68 net/bluetooth/hci_sock.c:91
Read of size 2 at addr ffff0000c48885b2 by task syz.4.334/7318
mgmt_pending_find_data() last use was removed in 2021 by
commit 5a7501374664 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CLOCK_INFO")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 6fe26f694c82 ("Bluetooth: MGMT: Protect mgmt_pending list with its own lock") Signed-off-by: Sasha Levin <sashal@kernel.org>
This reworks MGMT_OP_REMOVE_ADV_MONITOR to not use mgmt_pending_add to
avoid crashes like bellow:
==================================================================
BUG: KASAN: slab-use-after-free in mgmt_remove_adv_monitor_complete+0xe5/0x540 net/bluetooth/mgmt.c:5406
Read of size 8 at addr ffff88801c53f318 by task kworker/u5:5/5341
Modify the driver to post 3 fewer buffers than the maximum rx buffers
(64) allowed for the firmware. This change mitigates a hardware issue
causing a race condition in the firmware, improving stability and data
handling.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This change addresses latency issues observed in HID use cases where
events arrive in bursts. By increasing the Rx descriptor count to 64,
the firmware can handle bursty data more effectively, reducing latency
and preventing buffer overflows.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver was posting only 6 rx buffers, despite the maximum rx buffers
being defined as 16. Having fewer RX buffers caused firmware exceptions
in HID use cases when events arrived in bursts.
Exception seen on android 6.12 kernel.
E Bluetooth: hci0: Received hw exception interrupt
E Bluetooth: hci0: Received gp1 mailbox interrupt
D Bluetooth: hci0: 00000000: ff 3e 87 80 03 01 01 01 03 01 0c 0d 02 1c 10 0e
D Bluetooth: hci0: 00000010: 01 00 05 14 66 b0 28 b0 c0 b0 28 b0 ac af 28 b0
D Bluetooth: hci0: 00000020: 14 f1 28 b0 00 00 00 00 fa 04 00 00 00 00 40 10
D Bluetooth: hci0: 00000030: 08 00 00 00 7a 7a 7a 7a 47 00 fb a0 10 00 00 00
D Bluetooth: hci0: 00000000: 10 01 0a
E Bluetooth: hci0: ---- Dump of debug registers —
E Bluetooth: hci0: boot stage: 0xe0fb0047
E Bluetooth: hci0: ipc status: 0x00000004
E Bluetooth: hci0: ipc control: 0x00000000
E Bluetooth: hci0: ipc sleep control: 0x00000000
E Bluetooth: hci0: mbox_1: 0x00badbad
E Bluetooth: hci0: mbox_2: 0x0000101c
E Bluetooth: hci0: mbox_3: 0x00000008
E Bluetooth: hci0: mbox_4: 0x7a7a7a7a
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ufshcd_err_handling_prepare() calls ufshcd_rpm_get_sync(). The latter
function can only succeed if UFSHCD_EH_IN_PROGRESS is not set because
resuming involves submitting a SCSI command and ufshcd_queuecommand()
returns SCSI_MLQUEUE_HOST_BUSY if UFSHCD_EH_IN_PROGRESS is set. Fix this
hang by setting UFSHCD_EH_IN_PROGRESS after ufshcd_rpm_get_sync() has
been called instead of before.
Relocate the runtime PM enable operation to sci_probe_single(). This change
prepares the codebase for upcoming fixes.
While at it, replace the existing logic with a direct call to
devm_pm_runtime_enable() and remove sci_cleanup_single(). The
devm_pm_runtime_enable() function automatically handles disabling runtime
PM during driver removal.
Fix a shortcoming in the bindings that doesn't allow for a separate
external clock.
The AXI PWMGEN IP block has a compile option ASYNC_CLK_EN that allows
the use of an external clock for the PWM output separate from the AXI
clock that runs the peripheral.
This was missed in the original bindings and so users were writing dts
files where the one and only clock specified would be the external
clock, if there was one, incorrectly missing the separate AXI clock.
The correct bindings are that the AXI clock is always required and the
external clock is optional (must be given only when HDL compile option
ASYNC_CLK_EN=1).
DTS example in the bindings should be indented with 2- or 4-spaces and
aligned with opening '- |', so correct any differences like 3-spaces or
mixtures 2- and 4-spaces in one binding.
No functional changes here, but saves some comments during reviews of
new patches built on existing code.
Using 3 cells allows to pass additional flags and is the normal
abstraction for new PWM descriptions. There are no device trees yet to
adapt to this change.
gs101 differs to other SoCs in that fltcon1 register doesn't
always exist. Additionally the offset of fltcon0 is not fixed
and needs to use the newly added eint_fltcon_offset variable.
Fixes: 4a8be01a1a7a ("pinctrl: samsung: Add gs101 SoC pinctrl configuration") Cc: stable@vger.kernel.org # depends on the previous three patches Reviewed-by: André Draszik <andre.draszik@linaro.org> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20250402-pinctrl-fltcon-suspend-v6-3-78ce0d4eb30c@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Refactor the existing platform specific suspend/resume callback
so that each SoC variant has it's own callback containing the
SoC specific logic.
This allows exynosautov920 to have a dedicated function for using
eint_con_offset and eint_mask_offset. Also it is easily extendable
for gs101 which will need dedicated logic for handling the varying
register offset of fltcon0 via eint_fltcon_offset.
Reviewed-by: André Draszik <andre.draszik@linaro.org> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20250402-pinctrl-fltcon-suspend-v6-2-78ce0d4eb30c@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Stable-dep-of: bdbe0a0f7100 ("pinctrl: samsung: add gs101 specific eint suspend/resume callbacks") Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures. With certain high GPU loads it is possible to
reach the critical hardware shutdown temperature of 120°C, endangering the
hardware and making it impossible to run certain applications.
Set up GPU cooling similar to the ACPI tables, by throttling the GPU speed
when reaching 95°C and polling every 200ms.
The firmware configures the TSENS controller with a maximum temperature of
120°C. When reaching that temperature, the hardware automatically triggers
a reset of the entire platform. Some of the thermal zones in x1e80100.dtsi
use a critical trip point of 125°C. It's impossible to reach those.
It's preferable to shut down the system cleanly before reaching the
hardware trip point. Make the critical temperature trip points consistent
by setting all of them to 115°C and apply a consistent hysteresis.
The ACPI tables also specify 115°C as critical shutdown temperature.
Cc: stable@vger.kernel.org Fixes: 4e915987ff5b ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-2-d110e44ac3f9@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RK3576's power domains have a peculiar design where the PD_NVM power
domain, of which the sdhci controller is a part, seemingly does not have
idempotent runtime disable/enable. The end effect is that if PD_NVM gets
turned off by the generic power domain logic because all the devices
depending on it are suspended, then the next time the sdhci device is
unsuspended, it'll hang the SoC as soon as it tries accessing the CQHCI
registers.
RK3576's UFS support needed a new dev_pm_genpd_rpm_always_on function
added to the generic power domains API to handle what appears to be a
similar hardware design.
Use this new function to ask for the same treatment in the sdhci
controller by giving rk3576 its own platform data with its own postinit
function. The benefit of doing this instead of marking the power domains
always on in the power domain core is that we only do this if we know
the platform we're running on actually uses the sdhci controller. For
others, keeping PD_NVM always on would be a waste, as they won't run
into this specific issue. The only other IP in PD_NVM that could be
affected is FSPI0. If it gets a mainline driver, it will probably want
to do the same thing.
Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Fixes: cfee1b507758 ("pmdomain: rockchip: Add support for RK3576 SoC") Cc: <stable@vger.kernel.org> # v6.15+ Link: https://lore.kernel.org/r/20250423-rk3576-emmc-fix-v3-1-0bf80e29967f@collabora.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For some usecases a consumer driver requires its device to remain power-on
from the PM domain perspective during runtime. Using dev PM qos along with
the genpd governors, doesn't work for this case as would potentially
prevent the device from being runtime suspended too.
To support these usecases, let's introduce dev_pm_genpd_rpm_always_on() to
allow consumers drivers to dynamically control the behaviour in genpd for a
device that is attached to it.
Sysfs interface for updating firmware for RMI devices is available even
when F34 probe fails. The code checks for presence of F34 "container"
pointer and then tries to use the function data attached to the
sub-device. F34 assigns the function data early, before it knows if
probe will succeed, leaving behind a stale pointer.
Fix this by expanding checks to not only test for presence of F34
"container" but also check if there is driver data assigned to the
sub-device, and call dev_set_drvdata() only after we are certain that
probe is successful.
This is not a complete fix, since F34 will be freed during firmware
update, so there is still a race when fetching and accessing this
pointer. This race will be addressed in follow-up changes.
Reported-by: Hanno Böck <hanno@hboeck.de> Fixes: 29fd0ec2bdbe ("Input: synaptics-rmi4 - add support for F34 device reflash") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/aBlAl6sGulam-Qcx@google.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 05a2f07db888 ("tools/power turbostat: read RAPL counters via
perf") that adds support to read RAPL counters via perf defines the
notion of a RAPL domain_id which is set to physical_core_id on
platforms which support per_core_rapl counters (Eg: AMD processors
Family 17h onwards) and is set to the physical_package_id on all the
other platforms.
However, the physical_core_id is only unique within a package and on
platforms with multiple packages more than one core can have the same
physical_core_id and thus the same domain_id. (For eg, the first cores
of each package have the physical_core_id = 0). This results in all
these cores with the same physical_core_id using the same entry in the
rapl_counter_info_perdomain[]. Since rapl_perf_init() skips the
perf-initialization for cores whose domain_ids have already been
visited, cores that have the same physical_core_id always read the
perf file corresponding to the physical_core_id of the first package
and thus the package-energy is incorrectly reported to be the same
value for different packages.
Note: This issue only arises when RAPL counters are read via perf and
not when they are read via MSRs since in the latter case the MSRs are
read separately on each core.
Fix this issue by associating each CPU with rapl_core_id which is
unique across all the packages in the system.
Fixes: 05a2f07db888 ("tools/power turbostat: read RAPL counters via perf") Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that propagation settings can only be changed for mounts located
in the caller's mount namespace. This change aligns permission checking
with the rest of mount(2).
Reviewed-by: Christian Brauner <brauner@kernel.org> Fixes: 07b20889e305 ("beginning of the shared-subtree proper") Reported-by: "Orlando, Noah" <Noah.Orlando@deshaw.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
9ffb14ef61ba "move_mount: allow to add a mount into an existing group"
breaks assertions on ->mnt_share/->mnt_slave. For once, the data structures
in question are actually documented.
Documentation/filesystem/sharedsubtree.rst:
All vfsmounts in a peer group have the same ->mnt_master. If it is
non-NULL, they form a contiguous (ordered) segment of slave list.
do_set_group() puts a mount into the same place in propagation graph
as the old one. As the result, if old mount gets events from somewhere
and is not a pure event sink, new one needs to be placed next to the
old one in the slave list the old one's on. If it is a pure event
sink, we only need to make sure the new one doesn't end up in the
middle of some peer group.
"move_mount: allow to add a mount into an existing group" ends up putting
the new one in the beginning of list; that's definitely not going to be
in the middle of anything, so that's fine for case when old is not marked
shared. In case when old one _is_ marked shared (i.e. is not a pure event
sink), that breaks the assumptions of propagation graph iterators.
Put the new mount next to the old one on the list - that does the right thing
in "old is marked shared" case and is just as correct as the current behaviour
if old is not marked shared (kudos to Pavel for pointing that out - my original
suggested fix changed behaviour in the "nor marked" case, which complicated
things for no good reason).
Reviewed-by: Christian Brauner <brauner@kernel.org> Fixes: 9ffb14ef61ba ("move_mount: allow to add a mount into an existing group") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Holding namespace_sem is enough to make sure that result remains valid.
It is *not* enough to avoid false negatives from __lookup_mnt(). Mounts
can be unhashed outside of namespace_sem (stuck children getting detached
on final mntput() of lazy-umounted mount) and having an unrelated mount
removed from the hash chain while we traverse it may end up with false
negative from __lookup_mnt(). We need to sample and recheck the seqlock
component of mount_lock...
Bug predates the introduction of path_overmount() - it had come from
the code in finish_automount() that got abstracted into that helper.
Reviewed-by: Christian Brauner <brauner@kernel.org> Fixes: 26df6034fdb2 ("fix automount/automount race properly") Fixes: 6ac392815628 ("fs: allow to mount beneath top mount") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If iov_offset is non-zero, then we need to consider iov_offset in length
calculation, otherwise we might pass smaller IOs such as 512 bytes, in
below scenario [1].
This issue is reproducible using lib-uring test/fixed-seg.c application
with fixed buffer on a 512 LBA formatted device.
[1]
At present we pass the alignment check, for 512 LBA formatted devices,
len_mask = 511 when IO is smaller, i->count = 512 has an offset,
i->io_offset = 3584 with bvec values, bvec->bv_offset = 256,
bvec->bv_len = 3840. In short, the first 256 bytes are in the current
page, next 256 bytes are in the another page. Ideally we expect to
fail the IO.
I can think of 2 userspace scenarios where we experience this.
a: From userspace, we observe a different behaviour when device LBA
size is 512 vs 4096 bytes. For 4096 LBA formatted device, I see the
same liburing test [2] failing, whereas 512 the test passes without
this. This is reproducible everytime.
[2] https://github.com/axboe/liburing/
b: Although I was not able to reproduce the below condition, but I
suspect below case should be possible from user space for devices
with 512 LBA formatted device. Lets say from userspace while
allocating a virtually single chunk of memory, if we get 2 physical
chunk of memory, and IO happens to be at the boundary of first
physical chunk with length crossing first chunk, then we allow IOs
to proceed and hence we might map wrong physical address length and
proceed with IO rather than failing.
: --- a/test/fixed-seg.c
: +++ b/test/fixed-seg.c
: @@ -64,7 +64,7 @@ static int test(struct io_uring *ring, int fd, int
: vec_off)
: return T_EXIT_FAIL;
: }
:
: - ret = read_it(ring, fd, 4096, vec_off);
: + ret = read_it(ring, fd, 4096, 7*512 + 256);
: if (ret) {
: fprintf(stderr, "4096 0 failed\n");
: return T_EXIT_FAIL;
Effectively this is a write crossing the page boundary.
The removed dai_link->platform component cause a fail which
is exposed at runtime. (ex: when a sound tool is used)
This patch re-adds the dai_link->platform component to have
a full card registered.
Before this patch:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 1: HDMI [HDMI], device 0: HDMI snd-soc-dummy-dai-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ speaker-test -D plughw:1,0 -t sine
speaker-test 1.2.8
Playback device is plughw:1,0
Stream parameters are 48000Hz, S16_LE, 1 channels
Sine wave rate is 440.0000Hz
Playback open error: -22,Invalid argument
After this patch which restores the platform component:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDMI], device 0: HDMI snd-soc-dummy-dai-0 [HDMI snd-soc-dummy-dai-0]
Subdevices: 0/1
Subdevice #0: subdevice #0
The procedure handling IPC timeouts and EXCEPTION_CAUGHT notification
shall cancel any D0IX work before proceeding with DSP recovery. If
SET_D0IX called from delayed_work is the failing IPC the procedure will
deadlock. Conditionally skip cancelling the work to fix that.
Fixes: 335c4cbd201d ("ASoC: Intel: avs: D0ix power state support") Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Link: https://patch.msgid.link/20250530141025.2942936-3-cezary.rojewski@intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RPM manipulation in hda_codec_probe_complete()'s error path is
superfluous and leads to RPM usage count underflow if the
build-controls operation fails.
hda_codec_probe_complete() is called in:
1) hda_codec_probe() for all non-HDMI codecs
2) in card->late_probe() for HDMI codecs
Error path for hda_codec_probe() takes care of bus' RPM already.
For 2) if late_probe() fails, ASoC performs card cleanup what
triggers hda_codec_remote() - same treatment is in 1).
Prevent calling phy_exit() before phy_init() to avoid abnormal power
count and the following warning during boot up.
[5.146763] phy phy-1d80000.phy.0: phy_power_on was called before phy_init
Fixes: 7bac65687510 ("scsi: ufs: qcom: Power off the PHY if it was already powered on in ufs_qcom_power_up_sequence()") Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> Link: https://lore.kernel.org/r/20250526153821.7918-2-quic_nitirawa@quicinc.com Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kernel currently validates that the length of the provided nexthop
address does not exceed the specified length. This can lead to the
kernel reading uninitialized memory if user space provided a shorter
length than the specified one.
Fix by validating that the provided length exactly matches the specified
one.
Fixes: d1df6fd8a1d2 ("ipv6: sr: define core operations for seg6local lightweight tunnel") Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250604113252.371528-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enable threaded NAPI by default for WireGuard devices in response to low
performance behavior that we observed when multiple tunnels (and thus
multiple wg devices) are deployed on a single host. This affects any
kind of multi-tunnel deployment, regardless of whether the tunnels share
the same endpoints or not (i.e., a VPN concentrator type of gateway
would also be affected).
The problem is caused by the fact that, in case of a traffic surge that
involves multiple tunnels at the same time, the polling of the NAPI
instance of all these wg devices tends to converge onto the same core,
causing underutilization of the CPU and bottlenecking performance.
This happens because NAPI polling is hosted by default in softirq
context, but the WireGuard driver only raises this softirq after the rx
peer queue has been drained, which doesn't happen during high traffic.
In this case, the softirq already active on a core is reused instead of
raising a new one.
As a result, once two or more tunnel softirqs have been scheduled on
the same core, they remain pinned there until the surge ends.
In our experiments, this almost always leads to all tunnel NAPIs being
handled on a single core shortly after a surge begins, limiting
scalability to less than 3× the performance of a single tunnel, despite
plenty of unused CPU cores being available.
The proposed mitigation is to enable threaded NAPI for all WireGuard
devices. This moves the NAPI polling context to a dedicated per-device
kernel thread, allowing the scheduler to balance the load across all
available cores.
On our 32-core gateways, enabling threaded NAPI yields a ~4× performance
improvement with 16 tunnels, increasing throughput from ~13 Gbps to
~48 Gbps. Meanwhile, CPU usage on the receiver (which is the bottleneck)
jumps from 20% to 100%.
We have found no performance regressions in any scenario we tested.
Single-tunnel throughput remains unchanged.
Recent Qualcomm chipsets like SDX72/75 require MBIM sessionId mapping
to muxId in the range (0x70-0x8F) for the PCIe tethered use.
This has been partially addressed by the referenced commit, mapping
the default data call to muxId = 112, but the multiplexed data calls
scenario was not properly considered, mapping sessionId = 1 to muxId
1, while it should have been 113.
Fix this by moving the session_id assignment logic to mhi_mbim_newlink,
in order to map sessionId = n to muxId = n + WDS_BIND_MUX_DATA_PORT_MUX_ID.
Fixes: 65bc58c3dcad ("net: wwan: mhi: make default data link id configurable") Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com> Link: https://patch.msgid.link/20250603091204.2802840-1-dnlplm@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
S1G beacons are not traditional beacons but a type of extension frame.
Extension frames contain the frame control and duration fields, followed
by zero or more optional fields before the frame body. These optional
fields are distinct from the variable length elements.
The presence of optional fields is indicated in the frame control field.
To correctly locate the elements offset, the frame control must be parsed
to identify which optional fields are present. Currently, mac80211 parses
S1G beacons based on fixed assumptions about the frame layout, without
inspecting the frame control field. This can result in incorrect offsets
to the "variable" portion of the frame.
Properly parse S1G beacon frames by using the field lengths defined in
IEEE 802.11-2024, section 9.3.4.3, ensuring that the elements offset is
calculated accurately.
According to OpenMDK, bit 2 of the RGMII register has a different
meaning for BCM53115 [1]:
"DLL_IQQD 1: In the IDDQ mode, power is down0: Normal function
mode"
Configuring RGMII delay works without setting this bit, so let's keep it
at the default. For other chips, we always set it, so not clearing it
is not an issue.
One would assume BCM53118 works the same, but OpenMDK is not quite sure
what this bit actually means [2]:
"BYPASS_IMP_2NS_DEL #1: In the IDDQ mode, power is down#0: Normal
function mode1: Bypass dll65_2ns_del IP0: Use
dll65_2ns_del IP"
Add RGMII to supported interfaces for BCM63xx RGMII ports so they can be
actually used in RGMII mode.
Without this, phylink will fail to configure them:
[ 3.580000] b53-switch 10700000.switch GbE3 (uninitialized): validation of rgmii with support 0000000,00000000,00000000,000062ff and advertisement 0000000,00000000,00000000,000062ff failed: -EINVAL
[ 3.600000] b53-switch 10700000.switch GbE3 (uninitialized): failed to connect to PHY: -EINVAL
[ 3.610000] b53-switch 10700000.switch GbE3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Fixes: ce3bf94871f7 ("net: dsa: b53: add support for BCM63xx RGMIIs") Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Link: https://patch.msgid.link/20250602193953.1010487-5-jonas.gorski@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In MII mode, Tx lines are swapped for port0 and port1, which means
Tx port0 receives data from PRU1 and the Tx port1 receives data from
PRU0. This is an expected hardware behavior and reading the Tx stats
needs to be handled accordingly in the driver. Update the driver to
read Tx stats from the PRU1 for port0 and PRU0 for port1.
The logic added in the blamed commit was supposed to only omit nat source
port allocation if neither the existing nor the new entry are subject to
NAT.
However, its not enough to lookup the conntrack based on the proposed
tuple, we must also check the reverse direction.
Otherwise there are esoteric cases where the collision is in the reverse
direction because that colliding connection has a port rewrite, but the
new entry doesn't. In this case, we only check the new entry and then
erronously conclude that no clash exists anymore.
The existing (udp) tuple is:
a:p -> b:P, with nat translation to s:P, i.e. pure daddr rewrite,
reverse tuple in conntrack table is s:P -> a:p.
When another UDP packet is sent directly to s, i.e. a:p->s:P, this is
correctly detected as a colliding entry: tuple is taken by existing reply
tuple in reverse direction.
But the colliding conntrack is only searched for with unreversed
direction, and we can't find such entry matching a:p->s:P.
The incorrect conclusion is that the clashing entry has timed out and
that no port address translation is required.
Such conntrack will then be discarded at nf_confirm time because the
proposed reverse direction clashes with an existing mapping in the
conntrack table.
Search for the reverse tuple too, this will then check the NAT bits of
the colliding entry and triggers port reallocation.
Followp patch extends nft_nat.sh selftest to cover this scenario.
The IPS_SEQ_ADJUST change is also a bug fix:
Instead of checking for SEQ_ADJ this tested for SEEN_REPLY and ASSURED
by accident -- _BIT is only for use with the test_bit() API.
This bug has little consequence in practice, because the sequence number
adjustments are only useful for TCP which doesn't support clash resolution.
The existing test case (conntrack_reverse_clash.sh) exercise a race
condition path (parallel conntrack creation on different CPUs), so
the colliding entries have neither SEEN_REPLY nor ASSURED set.
Thanks to Yafang Shao and Shaun Brady for an initial investigation
of this bug.
The command specific status code, 0x183, was introduced in the NVMe 2.0
specification defined to "Command Size Limits Exceeded" and only ever
applied to DSM and Copy commands. Fix the name and, remove the
incorrect translation to error codes and special treatment in the
target code for it.
Commit 03f1444016b7 ("PM: sleep: Fix handling devices with direct_complete
set on errors") caused power.is_suspended to be set for devices with
power.direct_complete set, but it forgot to ensure the clearing of that
flag for them in device_resume(), so power.is_suspended is still set for
them during the next system suspend-resume cycle.
If that cycle is aborted in dpm_suspend(), the subsequent invocation of
dpm_resume() will trigger a device_resume() call for every device and
because power.is_suspended is set for the devices in question, they will
not be skipped by device_resume() as expected which causes scary error
messages to be logged (as appropriate).
To address this issue, move the clearing of power.is_suspended in
device_resume() immediately after the power.is_suspended check so it
will be always cleared for all devices processed by that function.
Fixes: 03f1444016b7 ("PM: sleep: Fix handling devices with direct_complete set on errors") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4280 Reported-and-tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://patch.msgid.link/4990586.GXAFRqVoOG@rjwysocki.net Signed-off-by: Sasha Levin <sashal@kernel.org>
We have the logic to include net/lib automatically for net related
selftests. However, currently, this logic is only in install target
which means only `make install` will have net/lib included. This commit
adds the logic to all target so that all `make`, `make run_tests` and
`make install` will have net/lib included in net related selftests.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com> Link: https://patch.msgid.link/20250601142914.13379-1-minhquangbui99@gmail.com Fixes: b86761ff6374 ("selftests: net: add scaffolding for Netlink tests in Python") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3d010c8031e3 ("udp: do not accept non-tunnel GSO skbs landing
in a tunnel") added checks in linux stack to not accept non-tunnel
GRO packets landing in a tunnel. This exposed an issue in vmxnet3
which was not correctly reporting GRO packets for tunnel packets.
This patch fixes this issue by setting correct GSO type for the
tunnel packets.
Currently, vmxnet3 does not support reporting inner fields for LRO
tunnel packets. The issue is not seen for egress drivers that do not
use skb inner fields. The workaround is to enable tnl-segmentation
offload on the egress interfaces if the driver supports it. This
problem pre-exists this patch fix and can be addressed as a separate
future patch.
Fixes: dacce2be3312 ("vmxnet3: add geneve and vxlan tunnel offload support") Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com> Acked-by: Guolin Yang <guolin.yang@broadcom.com> Link: https://patch.msgid.link/20250530152701.70354-1-ronak.doshi@broadcom.com
[pabeni@redhat.com: dropped the changelog] Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When driver handles the napi rx polling requests, the netdev might
have been released by the dellink logic triggered by the disconnect
operation on user plane. However, in the logic of processing skb in
polling, an invalid netdev is still being used, which causes a panic.
Commit a1e40ac5b5e9 ("net: gso: fix udp gso fraglist segmentation after
pull from frag_list") detected invalid geometry in frag_list skbs and
redirects them from skb_segment_list to more robust skb_segment. But some
packets with modified geometry can also hit bugs in that code. We don't
know how many such cases exist. Addressing each one by one also requires
touching the complex skb_segment code, which risks introducing bugs for
other types of skbs. Instead, linearize all these packets that fail the
basic invariants on gso fraglist skbs. That is more robust.
If only part of the fraglist payload is pulled into head_skb, it will
always cause exception when splitting skbs by skb_segment. For detailed
call stack information, see below.
Valid SKB_GSO_FRAGLIST skbs
- consist of two or more segments
- the head_skb holds the protocol headers plus first gso_size
- one or more frag_list skbs hold exactly one segment
- all but the last must be gso_size
Optional datapath hooks such as NAT and BPF (bpf_skb_pull_data) can
modify fraglist skbs, breaking these invariants.
In extreme cases they pull one part of data into skb linear. For UDP,
this causes three payloads with lengths of (11,11,10) bytes were
pulled tail to become (12,10,10) bytes.
The skbs no longer meets the above SKB_GSO_FRAGLIST conditions because
payload was pulled into head_skb, it needs to be linearized before pass
to regular skb_segment.
Fixes: a1e40ac5b5e9 ("gso: fix udp gso fraglist segmentation after pull from frag_list") Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a rare race condition when preparing for a reset where
guc_lrc_desc_unpin() could be in the process of deregistering a context
while a different thread is scrubbing outstanding contexts and it alters
the context state and does a wakeref put. Then, if there is a failure
with deregister_context(), a second wakeref put could occur. As a result
the wakeref count could drop below 0 and fail an INTEL_WAKEREF_BUG_ON()
check.
Therefore if there is a failure with deregister_context(), undo the
context state changes and do a wakeref put only if the context was set
to be destroyed earlier.
v2: Expand comment to better explain change. (Daniele)
v3: Removed addition to the original comment. (Daniele)
Fixes: 2f2cc53b5fe7 ("drm/i915/guc: Close deregister-context race against CT-loss") Signed-off-by: Jesus Narvaez <jesus.narvaez@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Alan Previn <alan.previn.teres.alexis@intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Cc: Mousumi Jana <mousumi.jana@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://lore.kernel.org/r/20250528230551.1855177-1-jesus.narvaez@intel.com
(cherry picked from commit f36a75aba1c3176d177964bca76f86a075d2943a) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When sending a H2G message where a reply is expected in
guc_submission_send_busy_loop(), outstanding_submission_g2h is
incremented before the send. However, if there is an error sending the
message, outstanding_submission_g2h is decremented without checking if a
reply is expected.
Therefore, check if reply is expected when there is a failure before
decrementing outstanding_submission_g2h.
Fixes: 2f2cc53b5fe7 ("drm/i915/guc: Close deregister-context race against CT-loss") Signed-off-by: Jesus Narvaez <jesus.narvaez@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Alan Previn <alan.previn.teres.alexis@intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Cc: Mousumi Jana <mousumi.jana@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://lore.kernel.org/r/20250514225224.4142684-1-jesus.narvaez@intel.com
(cherry picked from commit a6a26786f22a4ab0227bcf610510c4c9c2df0808) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the ptp_rate recorded earlier in the driver happens to be 0, this
bogus value will propagate up to EST configuration, where it will
trigger a division by 0.
Prevent this division by 0 by adding the corresponding check and error
code.
Suggested-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Fixes: 8572aec3d0dc ("net: stmmac: Add basic EST support for XGMAC") Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-2-d73340a794d5@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The stmmac platform drivers that do not open-code the clk_ptp_rate value
after having retrieved the default one from the device-tree can end up
with 0 in clk_ptp_rate (as clk_get_rate can return 0). It will
eventually propagate up to PTP initialization when bringing up the
interface, leading to a divide by 0:
Division by zero in kernel.
CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.30-00001-g48313bd5768a #22
Hardware name: STM32 (Device Tree Support)
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x6c/0x8c
dump_stack_lvl from Ldiv0_64+0x8/0x18
Ldiv0_64 from stmmac_init_tstamp_counter+0x190/0x1a4
stmmac_init_tstamp_counter from stmmac_hw_setup+0xc1c/0x111c
stmmac_hw_setup from __stmmac_open+0x18c/0x434
__stmmac_open from stmmac_open+0x3c/0xbc
stmmac_open from __dev_open+0xf4/0x1ac
__dev_open from __dev_change_flags+0x1cc/0x224
__dev_change_flags from dev_change_flags+0x24/0x60
dev_change_flags from ip_auto_config+0x2e8/0x11a0
ip_auto_config from do_one_initcall+0x84/0x33c
do_one_initcall from kernel_init_freeable+0x1b8/0x214
kernel_init_freeable from kernel_init+0x24/0x140
kernel_init from ret_from_fork+0x14/0x28
Exception stack(0xe0815fb0 to 0xe0815ff8)
Prevent this division by 0 by adding an explicit check and error log
about the actual issue. While at it, remove the same check from
stmmac_ptp_register, which then becomes duplicate
Fixes: 19d857c9038e ("stmmac: Fix calculations for ptp counters when clock input = 50Mhz.") Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Reviewed-by: Yanteng Si <si.yanteng@linux.dev> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-1-d73340a794d5@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Mailbox operations are not possible while the driver is in reset.
Operations that require MBX exchange with the control plane will result
in long delays if executed while a reset is in progress:
Disable mailbox communication in case of a reset, unless it's done during
a driver load, where the virtchnl operations are needed to configure the
device.
Fixes: 8077c727561aa ("idpf: add controlq init and reset checks") Co-developed-by: Joshua Hay <joshua.a.hay@intel.com> Signed-off-by: Joshua Hay <joshua.a.hay@intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Samuel Salin <Samuel.salin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a helper function to correctly handle the lockless
synchronization when the sender needs to block. The paradigm is
if (no_resources()) {
stop_queue();
barrier();
if (!no_resources())
restart_queue();
}
netif_subqueue_maybe_stop already handles the paradigm correctly, but
the code split the check for resources in three parts, the first one
(descriptors) followed the protocol, but the other two (completions and
tx_buf) were only doing the first part and so race prone.
Luckily netif_subqueue_maybe_stop macro already allows you to use a
function to evaluate the start/stop conditions so the fix only requires
the right helper function to evaluate all the conditions at once.
The patch removes idpf_tx_maybe_stop_common since it's no longer needed
and instead adjusts separately the conditions for singleq and splitq.
Note that idpf_tx_buf_hw_update doesn't need to check for resources
since that will be covered in idpf_tx_splitq_frame.
To reproduce:
Reduce the threshold for pending completions to increase the chances of
hitting this pause by changing your kernel:
The current implementation of the Tx scheduler allows the tree to be
rebuilt as the user adds more Tx queues to the VSI. In such a case,
additional child nodes are added to the tree to support the new number
of queues.
Unfortunately, this algorithm does not take into account that the limit
of the VSI support node may be exceeded, so an additional node in the
VSI layer may be required to handle all the requested queues.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs. Although the driver still respects the queue limit returned by
the FW, the Tx scheduler was unable to add those queues to its tree
and returned one of the errors below.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs (e.g. at least 321 CPUs, if there is already 128 Tx/Rx queue pairs).
Although the driver still respects the queue limit returned by the FW,
the Tx scheduler was unable to add those queues to its tree and returned
the following errors:
Failed VSI LAN queue config for XDP, error: -5
or:
Failed to set LAN Tx queue context, error: -22
Fix this problem by extending the tree rebuild algorithm to check if the
current VSI node can support the requested number of queues. If it
cannot, create as many additional VSI support nodes as necessary to
handle all the required Tx queues. Symmetrically, adjust the VSI node
removal algorithm to remove all nodes associated with the given VSI.
Also, make the search for the next free VSI node more restrictive. That is,
add queue group nodes only to the VSI support nodes that have a matching
VSI handle.
Finally, fix the comment describing the tree update algorithm to better
reflect the current scenario.
Fixes: b0153fdd7e8a ("ice: update VSI config dynamically") Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com> Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current implementation of the Tx scheduler tree attempts
to create nodes for all Tx queues, ignoring the fact that some
queues may already exist in the tree. For example, if the VSI
already has 128 Tx queues and the user requests for 16 new queues,
the Tx scheduler will compute the tree for 272 queues (128 existing
queues + 144 new queues), instead of 144 queues (128 existing queues
and 16 new queues).
Fix that by modifying the node count calculation algorithm to skip
the queues that already exist in the tree.
Fixes: 5513b920a4f7 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support") Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com> Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the XDP program is loaded, the XDP callback adds new Tx queues.
This means that the callback must update the Tx scheduler with the new
queue number. In the event of a Tx scheduler failure, the XDP callback
should also fail and roll back any changes previously made for XDP
preparation.
The previous implementation had a bug that not all changes made by the
XDP callback were rolled back. This caused the crash with the following
call trace:
[ +9.549584] ice 0000:ca:00.0: Failed VSI LAN queue config for XDP, error: -5
[ +0.382335] Oops: general protection fault, probably for non-canonical address 0x50a2250a90495525: 0000 [#1] SMP NOPTI
[ +0.010710] CPU: 103 UID: 0 PID: 0 Comm: swapper/103 Not tainted 6.14.0-net-next-mar-31+ #14 PREEMPT(voluntary)
[ +0.010175] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[ +0.010946] RIP: 0010:__ice_update_sample+0x39/0xe0 [ice]
Fix this by performing the missing unmapping of XDP queues from
q_vectors and setting the XDP rings pointer back to NULL after all those
queues are released.
Also, add an immediate exit from the XDP callback in case of ring
preparation failure.
Fixes: efc2214b6047 ("ice: Add support for XDP") Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com> Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270 Fixes: 27e2d4c8d28b ("Bluetooth: Add basic LE L2CAP connect request receiving support") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running these commands on DUT (and similar at the other end)
ip link set dev eth0 up
ip link add link eth0 name eth0.10 type vlan id 10
ip addr add 10.0.0.1/24 dev eth0.10
ip link set dev eth0.10 up
ping 10.0.0.2
The ping will fail.
The reason why is failing is because, the network interfaces for lan966x
have a flag saying that the HW can insert the vlan tags into the
frames(NETIF_F_HW_VLAN_CTAG_TX). Meaning that the frames that are
transmitted don't have the vlan tag inside the skb data, but they have
it inside the skb. We already get that vlan tag and put it in the IFH
but the problem is that we don't configure the HW to rewrite the frame
when the interface is in host mode.
The fix consists in actually configuring the HW to insert the vlan tag
if it is different than 0.
The "freq" variable is in terms of MHz and "max_val_cycles" is in terms
of Hz. The fact that "max_val_cycles" is a u64 suggests that support
for high frequency is intended but the "freq_khz * 1000" would overflow
the u32 type if we went above 4GHz. Use unsigned long long type for the
mutliplication to prevent that.
Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/aDbFHe19juIJKjsb@stanley.mountain Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Identify the cause of the suspend/resume hang: netif_carrier_off()
is called during link state changes and becomes stuck while
executing linkwatch_work().
To resolve this issue, call netif_device_detach() during the Ethernet
suspend process to temporarily detach the network device from the
kernel and prevent the suspend/resume hang.
Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver") Signed-off-by: Yanqing Wang <ot_yanqing.wang@mediatek.com> Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Signed-off-by: Biao Huang <biao.huang@mediatek.com> Link: https://patch.msgid.link/20250528075351.593068-1-macpaul.lin@mediatek.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
