Perry Melange [Wed, 7 Aug 2019 17:25:13 +0000 (19:25 +0200)]
ath79: add support for D-Link DIR-842 C3
Hardware spec of DIR-842 C3:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or
the u-boot failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted.
Otherwise the u-boot will enter failsafe mode as the checksum
of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the
firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
just upgrade the factory.bin through the u-boot failsafe interface
and then goto step 2.
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
This seems to be identical to CPE210 v1 despite having removable
antennas.
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Based on the work of Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
tplink-safeloader: increase kernel partition for CPE/WBSx10v1
This is a preparation for ath79 support of the CPE210/CPE510 v1.
Kernel size is chosen equal to the latest update for CPE610 v1.
This also updates the partition size in ar71xx target, so code
remains consistent if someone looks up the device. Since CPE210,
CPE510, WBS210 and WBS510 (all v1) share the same partition
layout definition, and are on deprecated target anyway, this
changes them all at once.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Jo-Philipp Wich [Wed, 7 Aug 2019 05:15:07 +0000 (07:15 +0200)]
packages: apply usign padding workarounds to package indexes if needed
Since usign miscalculates SHA-512 digests for input sizes of exactly
64 + N * 128 + 110 or 64 + N * 128 + 111 bytes, we need to apply some
white space padding to avoid triggering the hashing edge case.
While usign itself has been fixed already, there is still many firmwares
in the wild which use broken usign versions to verify current package
indexes so we'll need to carry this workaround in the forseeable future.
Jo-Philipp Wich [Tue, 6 Aug 2019 19:22:27 +0000 (21:22 +0200)]
config: introduce separate CONFIG_SIGNATURE_CHECK option
Introduce a new option CONFIG_SIGNATURE_CHECK which defaults to the value
of CONFIG_SIGNED_PACKAGES and thus is enabled by default.
This option is needed to support building target opkg with enabled
signature verification while having the signed package lists disabled.
Our buildbots currently disable package signing globally in the
buildroot and SDK to avoid the need to ship private signing keys to
the build workers and to prevent the triggering of random key generation
on the worker nodes since package signing happens off-line on the master
nodes.
As unintended side-effect, updated opkg packages will get built with
disabled signature verification, hence the need for a new override option.
Jo-Philipp Wich [Tue, 6 Aug 2019 18:55:39 +0000 (20:55 +0200)]
usign: update to latest Git HEAD
This update fixes usign signature verification on files with certain
file sizes triggering a bug in the shipped SHA-512 implementation.
5a52b37 sha512: fix bad hardcoded constant in sha512_final() 3e6648b README: replace unicode character 716c3f2 README: add reference to OpenBSD signify 86d3668 README: provide reference for ed25519 algorithm 939ec35 usign: main.c: describe necessary arguments for -G
Rafał Miłecki [Tue, 6 Aug 2019 08:01:15 +0000 (10:01 +0200)]
kernel: drop Fon(Foxconn) parser matching for the "firmware" partition
This parser's matching function appears to be too generic as it matches
e.g. Buffalo WZR-HP-G300NH. That results in incorrect parts parsing.
Luckily this parser is needed by Fon FON2601 only which uses DT-based
ramips target. It means we can depend on mtd subsystem matching of
"fonfxc,uimage" string.
That said triggering this parser based on the "firmware" (or whatever
MTD_SPLIT_FIRMWARE_NAME is) partiiton name is not needed. It can be
dropped which will automatically fix the Buffalo WZR-HP-G300NH case.
Fixes: a1c6a316d299 ("ramips: add support for Fon FON2601") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
mtdsplit_uimage_parse_fonfxc() gets called in two situations:
1) It was /requested/ from DT using "fonfxc,uimage" compatible string
2) It was called by parsing code after finding "firmware"
(MTD_SPLIT_FIRMWARE_NAME) due to the parser's type
Code added in the /fix/ commit basically just disabled the second case.
If that's the real goal it could be achieved by simply dropping type
MTD_PARSER_TYPE_FIRMWARE. It may however require another solution as
it's possible that some non-DT target actually needs fonfxc uImage
parsing.
Petr Štetiar [Mon, 5 Aug 2019 09:48:47 +0000 (11:48 +0200)]
adb: fix build breakage on recent musl
Fix build breakage as upstream has removed implicit include of
sys/sysmacros.h from sys/types.h:
remove implicit include of sys/sysmacros.h from sys/types.h
this reverts commit f552c792c7ce5a560f214e1104d93ee5b0833967, which
exposed the sysmacros.h macros (device major/minor calculations) for
BSD and GNU profiles to mimic an unintentional glibc behavior some
code depended on. glibc has deprecated and since removed them as the
resolution to bug #19239, so it makes no sense for us to keep this
behavior. affected code should all have been fixed by now, and if it's
not yet fixed it needs to be for use with modern glibc anyway.
GCC needs the kernel headers to compile.
Some GCC file includes asm/unistd.h which is provided by the kernel headers.
Normally the kernel headers build is very fast and ready before the gcc uses
it, but if it clones the kernel from a slow git repository it takes longer
and then it could be that the gcc already wants to use the kernel headers
before they are available. This patch fixes this problem by adding the
missing dependency.
mvebu: enable xHCI USB controller connected to PCIe
This commit fixes regression on Linksys WRT1900 (Mamba) where this device
doesn't have USB 3.0 controller integrated in SoC, instead it has Etron
EJ168 connected to PCIe lane. Previously enabled in kernel 4.4 and 4.9,
was lost in transition to 4.14.
Fixes: 4ccad92 ("mvebu: Add support for kernel 4.14") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Jeffery To [Sat, 3 Aug 2019 20:45:06 +0000 (04:45 +0800)]
build: include BUILD_VARIANT in PKG_BUILD_DIR
This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into
account (if set), so that packages do not need to manually override
PKG_BUILD_DIR just to handle variants.
This also updates most base packages with variants to use the updated
default PKG_BUILD_DIR.
ath79: add support for TP9343-based TP-Link TL-WR94x devices
This adds support for several TP-Link devices based on TP9343
("a QCA9561 without PCIe and USB"):
- TL-WR940N v3
- TL-WR940N v4
- TL-WR941ND v6
The devices are only different concerning LEDs and MAC address
assignment.
All TL-WR940 are with non-detachable antennas (N), all
TL-WR941 devices are with detachable antennas (ND).
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Hans Dedecker [Mon, 5 Aug 2019 18:59:38 +0000 (20:59 +0200)]
ethtool: bump to 5.2
379c096 Release version 5.2. 2bce6d9 ethtool: Add 100BaseT1 and 1000BaseT1 link modes 67ffbf5 ethtool: sync ethtool-copy.h with linux-next from 30/05/2019 687152b ethtool.spec: Use standard file location macros
Jackson Lim [Thu, 25 Jul 2019 14:44:11 +0000 (22:44 +0800)]
ath79: add support for D-Link DIR-842 C1
Hardware spec of DIR-842 C1:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or
the u-boot failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted.
Otherwise the u-boot will enter failsafe mode as the checksum
of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the
firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
just upgrade the factory.bin through the u-boot failsafe interface
and then goto step 2.
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[fix whitespace issues] Signed-off-by: David Bauer <mail@david-bauer.net>
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same
FCC ID, same TFTP image name...).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv11_tp_recovery.bin
(it's really v11, not v12)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv10_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Leon M. George [Fri, 26 Jul 2019 18:21:26 +0000 (20:21 +0200)]
ar71xx: wpj531: fix SIG1/RSS1 LED GPIO
In commit 6c937df749c7 ("ar71xx: wpj531: fix GPIOs for LED") wrong GPIO
13 for SIG1/RSS1 LED was commited, the correct GPIO number for this LED
is 12.
It's listed in "Hardware Guide - wpj531 7A06 (02/07/2019)" as GPIO12/RSS1
on the LED header and same GPIO 12 is used in the vendor's SDK as well.
Fixes: 6c937df749c7 ("ar71xx: wpj531: fix GPIOs for LED") Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit subject/message facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
NOGUCHI Hiroshi [Sat, 3 Aug 2019 10:46:10 +0000 (19:46 +0900)]
kernel: generic: fix fonfxc uimage parser
We cannot distinguish between fonfxc uImage and generic uImage because
fonfxc uImage header is almost same as generic uImage, except padding
length after image name.
The fonfxc uImage parser is available when specifying directly with DT
compatible property. So this patch adds check if the partition DT node
is compatible with the parser.
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2413 Fixes: a1c6a316d299 ("ramips: add support for Fon FON2601") Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[commit light touches and removed C code comment] Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 31 Jul 2019 16:11:01 +0000 (18:11 +0200)]
wireless-regdb: fix build when python2 from package feeds exists
wireless-regdb fails to build if there is python2 installed from package
feeds, as staging_dir/hostpkg/bin/python is python2 and
staging_dir/hostpkg/bin takes precedence over staging_dir/host/bin
(proper place with python -> python3 symlink) which leads to the build
failure of wireless-regdb, so this patch makes it explicit which python
should be used.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Russell Senior <russell@personaltelco.net> Tested-by: Lucian Cristian <lucian.cristian@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
ipq40xx: extend DT mdio node to be more accessible
The MDIO node will become more important in the future.
Hence, this patch adds DT labels to make the properties
inside the various subnodes more accessible.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Koen Vandeputte [Wed, 27 Mar 2019 09:36:41 +0000 (10:36 +0100)]
ar71xx: fix nand init issues on some rb2011 devices
While flashing lots of RB2011 devices, I noticed that
some of them refused to boot properly, failing over the NAND parameters.
Checking in detail shows that some device seem to use another NAND flash
which only support standard 2048-byte pages, without 512-byte subpage support.
This commit disables usage of these small subpage completely.
Advantages:
- Both NAND's with(out) subpage support are working now
- The nand speed increases a bit (measured roughly 1%) in typical usecases
Disadvantages:
- The maximum storage capacity decreases by ~0.2%
as small changes can consume a full page (2048 bytes) now.
new features:
- riscv64 port
- configure now allows customizing AR and RANLIB vars
- header-level support for new linux features in 5.1
major internal changes:
- removed extern __syscall; syscall header code is now fully self-contained
performance:
- new math library implementation for log/exp/pow
- aarch64 dynamic tlsdesc function is streamlined
compatibility & conformance:
- O_TTY_INIT is now defined
- sys/types.h no longer pollutes namespace with sys/sysmacros.h in any profile
- powerpc asm is now compatible with clang internal assembler
changes for new POSIX interpretations:
- fgetwc now sets stream error indicator on encoding errors
- fmemopen no longer rejects 0 size
bugs fixed:
- static TLS for shared libraries was allocated wrong on "Variant I" archs
- crash in dladdr reading through uninitialized pointer on non-match
- sigaltstack wrongly errored out on invalid ss_size when doing SS_DISABLE
- getdents function misbehaved with buffer length larger than INT_MAX
- set*id could deadlock after fork from multithreaded process
arch-specfic bugs fixed:
- s390x SO_PEERSEC definition was wrong
- passing of 64-bit syscall arguments was broken on microblaze
- posix_fadvise was broken on mips due to missing 7-arg syscall support
- vrregset_t layout and member naming was wrong on powerpc64
- add uart rom script address in header of sdma firmware to support
the uart driver of latest kernel working well while old firmware
assume ram script used for uart driver as NXP internal legacy
kernel.
- add multi-fifo SAI/PDM scripts.
This commit ports support for the ALFA Network AP121F, a pocket-size
router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the
ath79 target (it was already supported in ar71xx; see commit 0c6165d2
for more details).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed
DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env
partition writable] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Petr Štetiar [Sat, 27 Jul 2019 05:47:10 +0000 (07:47 +0200)]
scripts/ubinize-image.sh: fix buildbot breakage
New Docker based buildslaves install just bare minimum of packages, thus
not having bsdmainutils package installed which provides `hexdump`
utility, leading to the following build breakage on buildbots:
ubinize-image.sh: 12: /builder/scripts/ubinize-image.sh: hexdump: not found
So this patch simply replaces `hexdump` with `od` utility provided by
coreutils package, which should be likely available.
Co-authored-by: Yousong Zhou <yszhou4tech@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Fri, 26 Jul 2019 21:45:47 +0000 (23:45 +0200)]
tools/mklibs: update to 0.1.44 and convert to Python 3
Since the switch to Python 3 build fails if CONFIG_USE_MKLIBS is set
("Strip unnecessary functions from libraries" in menuconfig) as
mklibs hasn't been converted to run on Python 3.
* update to most recent upstream version which brings some
reproducibility fixes
* converted to Python 3 using 2to3
* fixed mixed tab/spaces indentation
* fixed use of string.* functions
* some more minor fixes to make Python 3 happy
Fixes commit 19938c8de7 ("build: switch to Python 3") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Tue, 4 Dec 2018 13:47:23 +0000 (14:47 +0100)]
autotools.mk: autoreconf: fix missing install-sh
I'm trying to create a package for libgpiod, which uses
AC_CONFIG_AUX_DIR macro, which is probably leading to the following
configure error:
autoreconf: running: /openwrt.git/staging_dir/host/bin/libtoolize --force
OpenWrt-libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR, `autostuff'.
OpenWrt-libtoolize: linking file `autostuff/ltmain.sh'
OpenWrt-libtoolize: putting macros in `m4'.
...
configure: error: cannot find install-sh, install.sh, or shtool in autostuff "."/autostuff
>From the build output it's clear, that libtoolize isn't installing
install-sh symlink, because libtoolize would install install-sh only if
it's being run with --install parameter. Corresponding part in
libtoolize:
if $opt_install; then
func_config_update config.guess \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
func_config_update config.sub \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
func_install_update install-sh \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
fi
func_ltmain_update ltmain.sh \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
Adding --install parameter to libtoolize fixes this build issue:
Petr Štetiar [Thu, 25 Jul 2019 07:21:42 +0000 (09:21 +0200)]
wireless-regdb: set PKGARCH:=all
As it's an architecture-independent binary file.
Ref: https://github.com/openwrt/openwrt/pull/1521#issuecomment-514687053 Suggested-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Petr Štetiar <ynezz@true.cz>
projects / thirdparty / openwrt.git / log
