André Apitzsch [Sun, 15 Jun 2025 20:35:03 +0000 (22:35 +0200)]
arm64: dts: qcom: msm8976: Make blsp_dma controlled-remotely
The blsp_dma controller is shared between the different subsystems,
which is why it is already initialized by the firmware. We should not
reinitialize it from Linux to avoid potential other users of the DMA
engine to misbehave.
In mainline this can be described using the "qcom,controlled-remotely"
property. In the downstream/vendor kernel from Qualcomm there is an
opposite "qcom,managed-locally" property. This property is *not* set
for the qcom,sps-dma@7884000 and qcom,sps-dma@7ac4000 [1] so adding
"qcom,controlled-remotely" upstream matches the behavior of the
downstream/vendor kernel.
Jie Gan [Wed, 11 Jun 2025 03:00:03 +0000 (11:00 +0800)]
arm64: dts: qcom: qcs615: disable the CTI device of the camera block
Disable the CTI device of the camera block to prevent potential NoC errors
during AMBA bus device matching.
The clocks for the Qualcomm Debug Subsystem (QDSS) are managed by aoss_qmp
through a mailbox. However, the camera block resides outside the AP domain,
meaning its QDSS clock cannot be controlled via aoss_qmp.
Fixes: bf469630552a ("arm64: dts: qcom: qcs615: Add coresight nodes") Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250611030003.3801-1-jie.gan@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Lijuan Gao [Mon, 26 May 2025 05:21:50 +0000 (13:21 +0800)]
arm64: dts: qcom: qcs615: Add IMEM and PIL info region
Add a simple-mfd representing IMEM on QCS615 and define the PIL
relocation info region as its child. The PIL region in IMEM is used to
communicate load addresses of remoteproc to post mortem debug tools, so
that these tools can collect ramdumps.
Kyle Deng [Mon, 26 May 2025 05:21:49 +0000 (13:21 +0800)]
arm64: dts: qcom: qcs615: Add mproc node for SEMP2P
The Shared Memory Point to Point (SMP2P) protocol facilitates
communication of a single 32-bit value between two processors.
Add these two nodes for remoteproc enablement on QCS615 SoC.
arm64: dts: qcom: Add support for X1-based Asus Zenbook A14
Initial support for Asus Zenbook A14. Particular moddel exists
in X1-26-100, X1P-42-100 (UX3407QA) and X1E-78-100 (UX3407RA).
Mostly similar to other X1-based laptops. Notable differences are:
* Wifi/Bluetooth combo being Qualcomm FastConnect 6900 on UX3407QA
and Qualcomm FastConnect 7800 on UX3407RA
* USB Type-C retimers are Parade PS8833, appear to behave identical
to Parade PS8830
* gpio90 is TZ protected
Working:
* Keyboard
* Touchpad
* NVME
* Lid switch
* Camera LED
* eDP (FHD OLED, SDC420D) with brightness control
* Bluetooth, WiFi (WCN6855)
* USB Type-A port
* USB Type-C ports in USB2/USB3/DP (both orientations)
* aDSP/cDPS firmware loading, battery info
* Sleep/suspend, nothing visibly broken on resume
Out of scope of this series:
* Audio (Speakers/microphones/headphone jack)
* Camera (OmniVision OV02C10)
* HDMI (Parade PS185HDM)
* EC
Add dtsi and create two configurations for UX3407QA, UX3407RA.
Tested on UX3407QA with X1-26-100.
Jie Gan [Thu, 22 May 2025 00:50:16 +0000 (08:50 +0800)]
arm64: dts: qcom: qcs615: fix a crash issue caused by infinite loop for Coresight
An infinite loop has been created by the Coresight devices. When only a
source device is enabled, the coresight_find_activated_sysfs_sink function
is recursively invoked in an attempt to locate an active sink device,
ultimately leading to a stack overflow and system crash. Therefore, disable
the replicator1 to break the infinite loop and prevent a potential stack
overflow.
Jagadeesh Kona [Tue, 15 Apr 2025 09:53:43 +0000 (09:53 +0000)]
arm64: dts: qcom: sa8775p: Add CPU OPP tables to scale DDR/L3
Add OPP tables required to scale DDR and L3 per freq-domain
on SA8775P platform.
If a single OPP table is used for both CPU domains, then
_allocate_opp_table() won't be invoked for CPU4 but instead
CPU4 will be added as device under the CPU0 OPP table. Due
to this, dev_pm_opp_of_find_icc_paths() won't be invoked for
CPU4 device and hence CPU4 won't be able to independently scale
it's interconnects. Both CPU0 and CPU4 devices will scale the
same ICC path which can lead to one device overwriting the BW
vote placed by other device. Hence CPU0 and CPU4 require separate
OPP tables to allow independent scaling of DDR and L3 frequencies
for each CPU domain, with the final DDR and L3 frequencies being
an aggregate of both.
Add Epoch Subsystem (EPSS) L3 interconnect provider node on SA8775P
SoCs. L3 instances on this SoC are same as SM8250 and SC7280 SoCs.
These SoCs use EPSS_L3_PERF register instead of REG_L3_VOTE register for
programming the perf level. This is taken care in the data associated
with the target specific compatible. Since, the HW is same in the all
SoCs with EPSS support, using the same generic compatible for all.
Stephan Gerhold [Tue, 8 Apr 2025 11:38:42 +0000 (13:38 +0200)]
arm64: dts: qcom: apq8016-sbc-d3-camera: Convert to DT overlay
Follow the example of the recently added apq8016-sbc-usb-host.dtso and
convert apq8016-sbc-d3-camera-mezzanine.dts to a DT overlay that can be
applied on top of the apq8016-sbc.dtb. This makes it more clear that
this is not a special type of DB410c but just an addon board that can
be added on top.
Functionally there should not be any difference since
apq8016-sbc-d3-camera-mezzanine.dtb is still generated as before
(but now by applying the overlay on top of apq8016-sbc.dtb).
Since dtc does not know that there are default #address/size-cells in
msm8916.dtsi, repeat those in the overlay to avoid dtc warnings because
it expects the wrong amount of address/size-cells.
It would be nice to have a generic overlay for the D3 camera mezzanine
(that can be applied to all 96Boards) but that's much more complicated
than providing a board-specific DT overlay as intermediate step.
Add the WiFi/BT nodes for XPS and describe the regulators for the WCN7850
combo chip using the new power sequencing bindings. All voltages are
derived from chained fixed regulators controlled using a single GPIO.
Based on the commit d09ab685a8f5 ("arm64: dts: qcom: x1e80100-qcp: Add
WiFi/BT pwrseq").
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: remove camcc status property
After a change enabling camera clock controller for all Qualcomm SM8250
boards the explicit control of the clock controller status can be removed
from the RB5 vision mezzanine dts overlay file.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250523092313.2625421-2-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
arm64: dts: qcom: sm8250: enable camcc clock controller by default
Enable camera clock controller on all Qualcomm SM8250 derived boards
by default due to the established agreement of having all clock
controllers enabled.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250523092313.2625421-1-vladimir.zapolskiy@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device nodes for most of the sound support - WSA884x smart speakers,
WCD9395 audio codec (headset) and sound card - which allows sound
playback via speakers and recording via AMIC microphones. Changes bring
necessary foundation for headset playback/recording via USB, but that
part is not yet ready.
Add device nodes for most of the sound support - WSA883x smart speakers,
WCD9395 audio codec (headset) and sound card - which allows sound
playback via speakers and recording via DMIC microphones. Changes bring
necessary foundation for headset playback/recording via USB, but that
part is not yet ready.
The usb_1_1 port doesn't have the PS8830 repeater, but apparently some
MUX for DP altmode control. After a suggestion from sgerhold on
'#aarch64-laptops' I added gpio-sbu-mux nodes from the x1e80100-QCP
tree, and this appears to work well. It is still guesswork, but
working guesswork.
dt-bindings: clock: qcom: Add missing bindings on gcc-sc8180x
The multi-media AHB clocks are needed to create HW dependency in
the multimedia CC dt blocks and avoid any issues. They were not
defined in the initial bindings. Add all the missing clock bindings
for gcc-sc8180x.
Enable SLPI, Sensors DSP on the Lenovo Yoga C630. The DSP boots the
firmware and provides QMI services, however it is of limited
functionality due to the missing fastrpc_shell_1 binary.
Linus Torvalds [Sun, 8 Jun 2025 18:33:00 +0000 (11:33 -0700)]
Merge tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanup from Thomas Gleixner:
"The delayed from_timer() API cleanup:
The renaming to the timer_*() namespace was delayed due massive
conflicts against Linux-next. Now that everything is upstream finish
the conversion"
* tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename from_timer() to timer_container_of()
Linus Torvalds [Sun, 8 Jun 2025 18:27:20 +0000 (11:27 -0700)]
Merge tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Cure IO bitmap inconsistencies
A failed fork cleans up all resources of the newly created thread
via exit_thread(). exit_thread() invokes io_bitmap_exit() which
does the IO bitmap cleanups, which unfortunately assume that the
cleanup is related to the current task, which is obviously bogus.
Make it work correctly
- A lockdep fix in the resctrl code removed the clearing of the
command buffer in two places, which keeps stale error messages
around. Bring them back.
- Remove unused trace events"
* tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/resctrl: Restore the rdt_last_cmd_clear() calls after acquiring rdtgroup_mutex
x86/iopl: Cure TIF_IO_BITMAP inconsistencies
x86/fpu: Remove unused trace events
Zhang Rui [Fri, 30 May 2025 00:09:28 +0000 (08:09 +0800)]
tools/power turbostat: Avoid probing the same perf counters
For the RAPL package energy status counter, Intel and AMD share the same
perf_subsys and perf_name, but with different MSR addresses.
Both rapl_counter_arch_infos[0] and rapl_counter_arch_infos[1] are
introduced to describe this counter for different Vendors.
As a result, the perf counter is probed twice, and causes a failure in
in get_rapl_counters() because expected_read_size and actual_read_size
don't match.
Fix the problem by skipping the already probed counter.
Note, this is not a perfect fix. For example, if different
vendors/platforms use the same MSR value for different purpose, the code
can be fooled when it probes a rapl_counter_arch_infos[] entry that does
not belong to the running Vendor/Platform.
In a long run, better to put rapl_counter_arch_infos[] into the
platform_features so that this becomes Vendor/Platform specific.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 09:44:50 +0000 (17:44 +0800)]
tools/power turbostat: Allow probing RAPL with platform_features->rapl_msrs cleared
platform_features->rapl_msrs describes the RAPL MSRs supported. While
RAPL Perf counters can be exposed from different kernel backend drivers,
e.g. RAPL MSR I/F driver, or RAPL TPMI I/F driver.
Thus, turbostat should first blindly probe all the available RAPL Perf
counters, and falls back to the RAPL MSR counters if they are listed in
platform_features->rapl_msrs.
With this, platforms that don't have RAPL MSRs can clear the
platform_features->rapl_msrs bits and use RAPL Perf counters only.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
probe_rapl_msr() is reused for probing RAPL MSR counters, cstate MSR
counters and MPERF/APERF/SMI MSR counters, thus its name is misleading.
Similar to add_perf_counter(), introduce add_msr_counter() to probe a
counter via MSR. Introduce wrapper function add_rapl_msr_counter() at
the same time to add extra check for Zero return value for specified
RAPL counters.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
As the only caller of add_cstate_perf_counter_(),
add_cstate_perf_counter() just gives extra debug output on top. There is
no need to keep both functions.
Remove add_cstate_perf_counter_() and move all the logic to
add_cstate_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
commit 05a2f07db888 ("tools/power turbostat: read RAPL counters via
perf") that adds support to read RAPL counters via perf defines the
notion of a RAPL domain_id which is set to physical_core_id on
platforms which support per_core_rapl counters (Eg: AMD processors
Family 17h onwards) and is set to the physical_package_id on all the
other platforms.
However, the physical_core_id is only unique within a package and on
platforms with multiple packages more than one core can have the same
physical_core_id and thus the same domain_id. (For eg, the first cores
of each package have the physical_core_id = 0). This results in all
these cores with the same physical_core_id using the same entry in the
rapl_counter_info_perdomain[]. Since rapl_perf_init() skips the
perf-initialization for cores whose domain_ids have already been
visited, cores that have the same physical_core_id always read the
perf file corresponding to the physical_core_id of the first package
and thus the package-energy is incorrectly reported to be the same
value for different packages.
Note: This issue only arises when RAPL counters are read via perf and
not when they are read via MSRs since in the latter case the MSRs are
read separately on each core.
Fix this issue by associating each CPU with rapl_core_id which is
unique across all the packages in the system.
Fixes: 05a2f07db888 ("tools/power turbostat: read RAPL counters via perf") Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com> Signed-off-by: Len Brown <len.brown@intel.com>
tools/power turbostat: Add Android support for MSR device handling
It uses /dev/msrN device paths on Android instead of /dev/cpu/N/msr,
updates error messages and permission checks to reflect the Android
device path, and wraps platform-specific code with #if defined(ANDROID)
to ensure correct behavior on both Android and non-Android systems.
These changes improve compatibility and usability of turbostat on
Android devices.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sun, 8 Jun 2025 18:07:33 +0000 (11:07 -0700)]
Merge tag 'perf-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf fix from Thomas Gleixner:
"A single fix for the x86 performance counters on Intel CPUs:
The MSR offset calculations for fixed performance counters are stored
at the wrong index in the configuration array causing the general
purpose counter MSR offset to be overwritten, so both the general
purpose and the fixed counters offsets are incorrect.
Correct the array index calculation to fix that"
* tag 'perf-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix incorrect MSR index calculations in intel_pmu_config_acr()
Linus Torvalds [Sun, 8 Jun 2025 18:02:53 +0000 (11:02 -0700)]
Merge tag 'irq-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for the PCI/MSI code:
The conversion to per device MSI domains created a MSI domain with
size 1 instead of sizing it to the maximum possible number of MSI
interrupts for the device. This "worked" as the subsequent allocations
resized the domain, but the recent change to move the prepare() call
into the domain creation path broke this works by chance mechanism.
Size the domain properly at creation time"
* tag 'irq-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Size device MSI domain with the maximum number of vectors
Linus Torvalds [Sun, 8 Jun 2025 17:35:12 +0000 (10:35 -0700)]
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mount fixes from Al Viro:
"Various mount-related bugfixes:
- split the do_move_mount() checks in subtree-of-our-ns and
entire-anon cases and adapt detached mount propagation selftest for
mount_setattr
- allow clone_private_mount() for a path on real rootfs
- fix a race in call of has_locked_children()
- fix move_mount propagation graph breakage by MOVE_MOUNT_SET_GROUP
- make sure clone_private_mnt() caller has CAP_SYS_ADMIN in the right
userns
- avoid false negatives in path_overmount()
- don't leak MNT_LOCKED from parent to child in finish_automount()
- do_change_type(): refuse to operate on unmounted/not ours mounts"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
do_change_type(): refuse to operate on unmounted/not ours mounts
clone_private_mnt(): make sure that caller has CAP_SYS_ADMIN in the right userns
selftests/mount_setattr: adapt detached mount propagation test
do_move_mount(): split the checks in subtree-of-our-ns and entire-anon cases
fs: allow clone_private_mount() for a path on real rootfs
fix propagation graph breakage by MOVE_MOUNT_SET_GROUP move_mount(2)
finish_automount(): don't leak MNT_LOCKED from parent to child
path_overmount(): avoid false negatives
fs/fhandle.c: fix a race in call of has_locked_children()
Linus Torvalds [Sun, 8 Jun 2025 17:20:21 +0000 (10:20 -0700)]
Merge tag '6.16-rc-part2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- multichannel/reconnect fixes
- move smbdirect (smb over RDMA) defines to fs/smb/common so they will
be able to be used in the future more broadly, and a documentation
update explaining setting up smbdirect mounts
- update email address for Paulo
* tag '6.16-rc-part2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
MAINTAINERS, mailmap: Update Paulo Alcantara's email address
cifs: add documentation for smbdirect setup
cifs: do not disable interface polling on failure
cifs: serialize other channels when query server interfaces is pending
cifs: deal with the channel loading lag while picking channels
smb: client: make use of common smbdirect_socket_parameters
smb: smbdirect: introduce smbdirect_socket_parameters
smb: client: make use of common smbdirect_socket
smb: smbdirect: add smbdirect_socket.h
smb: client: make use of common smbdirect.h
smb: smbdirect: add smbdirect.h with public structures
smb: client: make use of common smbdirect_pdu.h
smb: smbdirect: add smbdirect_pdu.h with protocol definitions
Linus Torvalds [Sun, 8 Jun 2025 15:19:01 +0000 (08:19 -0700)]
Merge tag 'trace-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull more tracing fixes from Steven Rostedt:
- Fix regression of waiting a long time on updating trace event filters
When the faultable trace points were added, it needed task trace RCU
synchronization.
This was added to the tracepoint_synchronize_unregister() function.
The filter logic always called this function whenever it updated the
trace event filters before freeing the old filters. This increased
the time of "trace-cmd record" from taking 13 seconds to running over
2 minutes to complete.
Move the freeing of the filters to call_rcu*() logic, which brings
the time back down to 13 seconds.
The error path of the ring_buffer_subbuf_order_set() released the
mutex too early and allowed subsequent accesses to setting the
subbuffer size to corrupt the data and cause a bug.
By moving the mutex locking to the end of the error path, it prevents
the reentrant access to the critical data and also allows the
function to convert the taking of the mutex over to the guard()
logic.
- Remove unused power management clock events
The clock events were added in 2010 for power management. In 2011 arm
used them. In 2013 the code they were used in was removed. These
events have been wasting memory since then.
- Fix sparse warnings
There was a few places that sparse warned about trace_events_filter.c
where file->filter was referenced directly, but it is annotated with
an __rcu tag. Use the helper functions and fix them up to use
rcu_dereference() properly.
* tag 'trace-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Add rcu annotation around file->filter accesses
tracing: PM: Remove unused clock events
ring-buffer: Fix buffer locking in ring_buffer_subbuf_order_set()
tracing: Fix regression of filter waiting a long time on RCU synchronization
Linus Torvalds [Sat, 7 Jun 2025 17:05:35 +0000 (10:05 -0700)]
Merge tag 'kbuild-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add support for the EXPORT_SYMBOL_GPL_FOR_MODULES() macro, which
exports a symbol only to specified modules
- Improve ABI handling in gendwarfksyms
- Forcibly link lib-y objects to vmlinux even if CONFIG_MODULES=n
- Add checkers for redundant or missing <linux/export.h> inclusion
- Deprecate the extra-y syntax
- Fix a genksyms bug when including enum constants from *.symref files
* tag 'kbuild-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (28 commits)
genksyms: Fix enum consts from a reference affecting new values
arch: use always-$(KBUILD_BUILTIN) for vmlinux.lds
kbuild: set y instead of 1 to KBUILD_{BUILTIN,MODULES}
efi/libstub: use 'targets' instead of extra-y in Makefile
module: make __mod_device_table__* symbols static
scripts/misc-check: check unnecessary #include <linux/export.h> when W=1
scripts/misc-check: check missing #include <linux/export.h> when W=1
scripts/misc-check: add double-quotes to satisfy shellcheck
kbuild: move W=1 check for scripts/misc-check to top-level Makefile
scripts/tags.sh: allow to use alternative ctags implementation
kconfig: introduce menu type enum
docs: symbol-namespaces: fix reST warning with literal block
kbuild: link lib-y objects to vmlinux forcibly even when CONFIG_MODULES=n
tinyconfig: enable CONFIG_LD_DEAD_CODE_DATA_ELIMINATION
docs/core-api/symbol-namespaces: drop table of contents and section numbering
modpost: check forbidden MODULE_IMPORT_NS("module:") at compile time
kbuild: move kbuild syntax processing to scripts/Makefile.build
Makefile: remove dependency on archscripts for header installation
Documentation/kbuild: Add new gendwarfksyms kABI rules
Documentation/kbuild: Drop section numbers
...
Linus Torvalds [Sat, 7 Jun 2025 17:00:03 +0000 (10:00 -0700)]
Merge tag 'sh-for-v6.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
- replace the __ASSEMBLY__ with __ASSEMBLER__ macro in all headers
since the latter is now defined automatically by both GCC and Clang
when compiling assembly code (Thomas Huth)
- set the default SPI mode for the ecovec24 board which became
necessary after a new mode member as added to the sh_msiof_spi_info
struct in cf9e4784f3bd ("spi: sh-msiof: Add slave mode support")
(Geert Uytterhoeven)
- remove unused variables in the kprobes code in
kprobe_exceptions_notify() (Mike Rapoport)
* tag 'sh-for-v6.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: kprobes: Remove unused variables in kprobe_exceptions_notify()
sh: ecovec24: Make SPI mode explicit
sh: Replace __ASSEMBLY__ with __ASSEMBLER__ in all headers
Linus Torvalds [Sat, 7 Jun 2025 16:56:18 +0000 (09:56 -0700)]
Merge tag 'loongarch-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Adjust the 'make install' operation
- Support SCHED_MC (Multi-core scheduler)
- Enable ARCH_SUPPORTS_MSEAL_SYSTEM_MAPPINGS
- Enable HAVE_ARCH_STACKLEAK
- Increase max supported CPUs up to 2048
- Introduce the numa_memblks conversion
- Add PWM controller nodes in dts
- Some bug fixes and other small changes
* tag 'loongarch-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
platform/loongarch: laptop: Unregister generic_sub_drivers on exit
platform/loongarch: laptop: Add backlight power control support
platform/loongarch: laptop: Get brightness setting from EC on probe
LoongArch: dts: Add PWM support to Loongson-2K2000
LoongArch: dts: Add PWM support to Loongson-2K1000
LoongArch: dts: Add PWM support to Loongson-2K0500
LoongArch: vDSO: Correctly use asm parameters in syscall wrappers
LoongArch: Fix panic caused by NULL-PMD in huge_pte_offset()
LoongArch: Preserve firmware configuration when desired
LoongArch: Avoid using $r0/$r1 as "mask" for csrxchg
LoongArch: Introduce the numa_memblks conversion
LoongArch: Increase max supported CPUs up to 2048
LoongArch: Enable HAVE_ARCH_STACKLEAK
LoongArch: Enable ARCH_SUPPORTS_MSEAL_SYSTEM_MAPPINGS
LoongArch: Add SCHED_MC (Multi-core scheduler) support
LoongArch: Add some annotations in archhelp
LoongArch: Using generic scripts/install.sh in `make install`
LoongArch: Add a default install.sh
Linus Torvalds [Sat, 7 Jun 2025 16:40:08 +0000 (09:40 -0700)]
Merge tag 'sound-fix-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fix patches for the 6.16-rc1 merge window.
Most of changes are about ASoC, especially lots of AVS driver fixes.
Larger LOCs are seen in TAS571x codec drivers, but the changes are
trivial and safe. The rest are all device-specific small fixes"
* tag 'sound-fix-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ASoC: Intel: avs: boards: Fix rt5663 front end name
ASoC: Intel: avs: Simplify verification of parse_int_array() result
ALSA: usb-audio: Add implicit feedback quirk for RODE AI-1
ALSA: hda: Ignore unsol events for cards being shut down
ALSA: hda: Add new pci id for AMD GPU display HD audio controller
ALSA: hda: cs35l41: Constify regmap_irq_chip
ALSA: usb-audio: Add a quirk for Lenovo Thinkpad Thunderbolt 3 dock
ASoC: ti: omap-hdmi: Re-add dai_link->platform to fix card init
ASoC: pcm: Do not open FEs with no BEs connected
ASoC: rt1320: fix speaker noise when volume bar is 100%
ASoC: Intel: avs: Include missing string.h
ASoC: Intel: avs: Verify content returned by parse_int_array()
ASoC: Intel: avs: Verify kcalloc() status when setting constraints
ASoC: Intel: avs: Fix paths in MODULE_FIRMWARE hints
ASoC: Intel: avs: Fix possible null-ptr-deref when initing hw
ASoC: Intel: avs: Fix PPLCxFMT calculation
ASoC: Intel: avs: Fix deadlock when the failing IPC is SET_D0IX
ASoC: codecs: hda: Fix RPM usage count underflow
ASoC: amd: yc: Add support for Lenovo Yoga 7 16ARP8
ASoC: tas571x: fix tas5733 num_controls
...
Linus Torvalds [Sat, 7 Jun 2025 14:24:07 +0000 (07:24 -0700)]
Merge tag 'ubifs-for-linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2 and UBIFS fixes from Richard Weinberger:
"JFFS2:
- Correctly check return code of jffs2_prealloc_raw_node_refs()
UBIFS:
- Spelling fixes"
* tag 'ubifs-for-linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: check jffs2_prealloc_raw_node_refs() result in few other places
jffs2: check that raw node were preallocated before writing summary
ubifs: Fix grammar in error message
Mike Rapoport [Sat, 17 May 2025 09:30:48 +0000 (12:30 +0300)]
sh: kprobes: Remove unused variables in kprobe_exceptions_notify()
kbuild reports the following warning:
arch/sh/kernel/kprobes.c: In function 'kprobe_exceptions_notify':
>> arch/sh/kernel/kprobes.c:412:24: warning: variable 'p' set but not used [-Wunused-but-set-variable]
412 | struct kprobe *p = NULL;
| ^
The variable 'p' is indeed unused since the commit fa5a24b16f94
("sh/kprobes: Don't call the ->break_handler() in SH kprobes code")
Remove that variable along with 'kprobe_opcode_t *addr' which also
becomes unused after 'p' is removed.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202505151341.EuRFR22l-lkp@intel.com/ Fixes: fa5a24b16f94 ("sh/kprobes: Don't call the ->break_handler() in SH kprobes code") Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Commit cf9e4784f3bde3e4 ("spi: sh-msiof: Add slave mode support") added
a new mode member to the sh_msiof_spi_info structure, but did not update
any board files. Hence all users in board files rely on the default
being host mode.
Make this unambiguous by configuring host mode explicitly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Thomas Huth [Fri, 14 Mar 2025 07:10:03 +0000 (08:10 +0100)]
sh: Replace __ASSEMBLY__ with __ASSEMBLER__ in all headers
While the GCC and Clang compilers already define __ASSEMBLER__
automatically when compiling assembly code, __ASSEMBLY__ is a
macro that only gets defined by the Makefiles in the kernel.
This can be very confusing when switching between userspace
and kernelspace coding, or when dealing with uapi headers that
rather should use __ASSEMBLER__ instead. So let's standardize on
the __ASSEMBLER__ macro that is provided by the compilers now.
This is a completely mechanical patch (done with a simple "sed -i"
statement).
Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Cc: linux-sh@vger.kernel.org Signed-off-by: Thomas Huth <thuth@redhat.com> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
projects / thirdparty / linux.git / log
