2. Also fix the same warning message in mtk_drm_drv.c
>> drivers/gpu/drm/mediatek/mtk_drm_drv.c:832:15:
warning: cast to smaller integer type 'enum mtk_ddp_comp_type'
from 'const void *' [-Wvoid-pointer-to-enum-cast]
The Display Data Channel (DDC) transactions between an HDMI transmitter
(SIL9022A in this case) and an HDMI monitor, occur at a maximum of
100KHz. That's the maximum supported frequency within DDC standards.
While the SIL9022A can transact with the core at 400KHz, it needs to
drop the frequency to 100KHz when communicating with the monitor,
otherwise, the i2c controller times out and shows warning like this.
[ 985.773431] omap_i2c 20010000.i2c: controller timed out
That feature, however, has not been enabled in the SIL9022 driver.
Since, dropping the frequency doesn't affect any other devices on the
bus, drop the main-i2c1 frequency from 400KHz to 100KHz.
Using GCC_DCD_XO_CLK as the XO clock for SDHCI controller is not correct,
it seems that I somehow made a mistake of passing it instead of the fixed
XO clock.
Fixes: 04b3b72b5b8f ("ARM: dts: qcom: ipq4019: Add SDHCI controller node") Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230811110150.229966-1-robert.marko@sartura.hr Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SoM A uses the EQOS ethernet interface and not the FEC, so drop the
interface pinctrl node from the device tree.
Fixes: c86d350aae68 ("arm64: dts: Add device tree for the Debix Model A Board") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes the interrupt range for wakeup and main domain gpio
interrupt routers. They were wrongly subtracted by 32 instead of
following what is defined in the interrupt map in the TRM (Table 9-35).
If reading the RX capabilities fails the training pattern will be set
wrongly: add error checking for drm_dp_read_dpcd_caps() and return if
anything went wrong with it.
While at it, also add a less critical error check when writing to
clear the ESI0 IRQ vector.
Fixes: f70ac097a2cf ("drm/mediatek: Add MT8195 Embedded DisplayPort driver") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-2-angelogioacchino.delregno@collabora.com/ Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
cq_extra is protected by ->completion_lock, which io_get_sqe() misses.
The bug is harmless as it doesn't happen in real life, requires invalid
SQ index array and racing with submission, and only messes up the
userspace, i.e. stall requests execution but will be cleaned up on
ring destruction.
The smaller of data->shallow_depth and __map_depth(sb, index)
will be used as the maximum range when allocating bits.
For a mmc device (one hw queue, deadline I/O scheduler):
q->nr_requests = sched_tags = 128, so according to the previous
calculation method, dd->async_depth = data->shallow_depth = 96,
and the platform is 64bits with 8 cpus, sched_tags.bitmap_tags.sb.shift=5,
sb.maps[]=32/32/32/32, 32 is smaller than 96, whether it is a read or
a write I/O, tags can be allocated to the maximum range each time,
which has not throttling effect.
In addition, refer to the methods of bfg/kyber I/O scheduler,
limit ratiois are calculated base on sched_tags.bitmap_tags.sb.shift.
This patch can throttle write requests really.
Fixes: 07757588e507 ("block/mq-deadline: Reserve 25% of scheduler tags for synchronous requests") Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/1691061162-22898-1-git-send-email-zhiguo.niu@unisoc.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tracefs or debugfs maybe cause hundreds to thousands of PATH records,
too many PATH records maybe cause soft lockup.
For example:
1. CONFIG_KASAN=y && CONFIG_PREEMPTION=n
2. auditctl -a exit,always -S open -k key
3. sysctl -w kernel.watchdog_thresh=5
4. mkdir /sys/kernel/debug/tracing/instances/test
There may be a soft lockup as follows:
watchdog: BUG: soft lockup - CPU#45 stuck for 7s! [mkdir:15498]
Kernel panic - not syncing: softlockup: hung tasks
Call trace:
dump_backtrace+0x0/0x30c
show_stack+0x20/0x30
dump_stack+0x11c/0x174
panic+0x27c/0x494
watchdog_timer_fn+0x2bc/0x390
__run_hrtimer+0x148/0x4fc
__hrtimer_run_queues+0x154/0x210
hrtimer_interrupt+0x2c4/0x760
arch_timer_handler_phys+0x48/0x60
handle_percpu_devid_irq+0xe0/0x340
__handle_domain_irq+0xbc/0x130
gic_handle_irq+0x78/0x460
el1_irq+0xb8/0x140
__audit_inode_child+0x240/0x7bc
tracefs_create_file+0x1b8/0x2a0
trace_create_file+0x18/0x50
event_create_dir+0x204/0x30c
__trace_add_new_event+0xac/0x100
event_trace_add_tracer+0xa0/0x130
trace_array_create_dir+0x60/0x140
trace_array_create+0x1e0/0x370
instance_mkdir+0x90/0xd0
tracefs_syscall_mkdir+0x68/0xa0
vfs_mkdir+0x21c/0x34c
do_mkdirat+0x1b4/0x1d4
__arm64_sys_mkdirat+0x4c/0x60
el0_svc_common.constprop.0+0xa8/0x240
do_el0_svc+0x8c/0xc0
el0_svc+0x20/0x30
el0_sync_handler+0xb0/0xb4
el0_sync+0x160/0x180
Therefore, we add cond_resched() to __audit_inode_child() to fix it.
Fixes: 5195d8e217a7 ("audit: dynamically allocate audit_names when not enough space is in the names array") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For normal GPU devfreq, we need to acquire the GMU lock while already
holding devfreq locks. But in the teardown path, we were calling
dev_pm_domain_detach() while already holding the GMU lock, resulting in
this lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
6.4.3-debug+ #3 Not tainted
------------------------------------------------------
ring0/391 is trying to acquire lock: ffffff80a025c078 (&devfreq->lock){+.+.}-{3:3}, at: qos_notifier_call+0x30/0x74
but task is already holding lock: ffffff809b8c1ce8 (&(c->notifiers)->rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x34/0x78
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
other info that might help us debug this:
Chain exists of:
&devfreq->lock --> dev_pm_qos_mtx --> &(c->notifiers)->rwsem
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
rlock(&(c->notifiers)->rwsem);
lock(dev_pm_qos_mtx);
lock(&(c->notifiers)->rwsem);
lock(&devfreq->lock);
Fix this by only synchronizing access to gmu->initialized.
Fixes: 4cd15a3e8b36 ("drm/msm/a6xx: Make GPU destroy a bit safer") Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/551171/ Signed-off-by: Sasha Levin <sashal@kernel.org>
The adreno_is_a20x() and adreno_is_a225() functions rely on the
GPU revision, but such information is retrieved inside adreno_gpu_init(),
which is called afterwards.
Fix this problem by caling adreno_gpu_init() earlier, so that
the GPU information revision is available when adreno_is_a20x()
and adreno_is_a225() run.
There is a upper bound to "catlen" but no lower bound to prevent
negatives. I don't see that this necessarily causes a problem but we
may as well be safe.
Fixes: e114e473771c ("Smack: Simplified Mandatory Access Control Kernel") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 1e7ac595fa46 ("drm/msm/dpu: pass irq to
dpu_encoder_helper_wait_for_irq()") the
dpu_encoder_phys_wb_wait_for_commit_done expects the IRQ index rather
than the IRQ index in phys_enc->intr table, however writeback got the
older invocation in place. This was unnoticed for several releases, but
now it's time to fix it.
Fixes: d7d0e73f7de3 ("drm/msm/dpu: introduce the dpu_encoder_phys_* for writeback") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/550924/ Link: https://lore.kernel.org/r/20230802100426.4184892-2-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Apparently no one noticed that mdp5 plane states leak like a sieve
ever since we introduced plane_state->commit refcount a few years ago
in 21a01abbe32a ("drm/atomic: Fix freeing connector/plane state too
early by tracking commits, v3.")
Fix it by using the right helpers.
Fixes: 21a01abbe32a ("drm/atomic: Fix freeing connector/plane state too early by tracking commits, v3.") Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Rob Clark <robdclark@gmail.com> Cc: Abhinav Kumar <quic_abhinavk@quicinc.com> Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Reported-and-tested-by: dorum@noisolation.com Cc: dorum@noisolation.com Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/551236/ Link: https://lore.kernel.org/r/20230803204521.928582-1-daniel.vetter@ffwll.ch Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The connector type and pixel format are missing for this panel,
add them to prevent various drivers from failing to determine
either of those parameters.
As the temporary buffer is no longer used to store 8-bit grayscale data,
its size can be reduced to the size needed to store the monochrome
bitmap data.
Fixes: 24c6bedefbe71de9 ("drm/repaper: Use format helper for xrgb8888 to monochrome conversion") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-6-geert@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Aspeed always report the display port as "connected", because it
doesn't set a .detect_ctx callback.
Fix this by providing the proper detect callback for astdp and dp501.
This also fixes the following regression:
Since commit fae7d186403e ("drm/probe-helper: Default to 640x480 if no
EDID on DP") The default resolution is now 640x480 when no monitor is
connected. But Aspeed graphics is mostly used in servers, where no monitor
is attached. This also affects the remote BMC resolution to 640x480, which
is inconvenient, and breaks the anaconda installer.
v2: Add .detect callback to the dp/dp501 connector (Jani Nikula)
v3: Use .detect_ctx callback, and refactors (Thomas Zimmermann)
Add a BMC virtual connector
v4: Better indent detect_ctx() functions (Thomas Zimmermann)
v5: Enable polling of the dp and dp501 connector status
(Thomas Zimmermann)
v6: Change check order in ast_astdp_is_connected (Jammy Huang)
Device core dump add block method adds hardware blocks to dumping queue
with stack behavior which causes the hardware blocks to be printed in
reverse order. Change the addition to dumping queue data structure
from "list_add" to "list_add_tail" for FIFO queue behavior.
Fixes: 98659487b845 ("drm/msm: add support to take dpu snapshot") Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Signed-off-by: Ryan McCann <quic_rmccann@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/546200/ Link: https://lore.kernel.org/r/20230622-devcoredump_patch-v5-1-67e8b66c4723@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several reasons why 'reconfig_mutex' should be held:
1) rdev_for_each() is not safe to be called without the lock, because
rdev can be removed concurrently.
2) mddev_destroy_serial_pool() and mddev_create_serial_pool() should not
be called concurrently.
3) mddev_suspend() from mddev_destroy/create_serial_pool() should be
protected by the lock.
Fixes: 10c92fca636e ("md-bitmap: create and destroy wb_info_pool with the change of backlog") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230706083727.608914-3-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Local variable is definied first in the beginning of backlog_store(),
there is no need to define it again.
Fixes: 8c13ab115b57 ("md/bitmap: don't set max_write_behind if there is no write mostly device") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230706083727.608914-2-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2ae6aaf76912 ("md/raid10: fix io loss while replacement replace
rdev") reads replacement first to prevent io loss. However, there are same
issue in wait_blocked_dev() and raid10_handle_discard(), too. Fix it by
using dereference_rdev_and_rrdev() to get devices.
Fixes: d30588b2731f ("md/raid10: improve raid10 discard request") Fixes: f2e7e269a752 ("md/raid10: pull the code that wait for blocked dev into one function") Signed-off-by: Li Nan <linan122@huawei.com> Link: https://lore.kernel.org/r/20230701080529.2684932-4-linan666@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Factor out a helper to get 'rdev' and 'replacement' from config->mirrors.
Just to make code cleaner and prepare to fix the bug of io loss while
'replacement' replace 'rdev'.
memalloc_noio_save() is called for the first mddev_suspend(), and
repeated mddev_suspend() only increase 'suspended'. However,
memalloc_noio_restore() is also called for the first mddev_resume(),
which means that memory reclaim will be enabled before the last
mddev_resume() is called, while the array is still suspended.
Fix this problem by restore 'noio_flag' for the last mddev_resume().
Fixes: 78f57ef9d50a ("md: use memalloc scope APIs in mddev_suspend()/mddev_resume()") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20230628012931.88911-3-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running sparse on fsl_qmc_audio (make C=1) raises the following warnings:
fsl_qmc_audio.c:387:26: warning: restricted snd_pcm_format_t degrades to integer
fsl_qmc_audio.c:389:59: warning: incorrect type in argument 1 (different base types)
fsl_qmc_audio.c:389:59: expected restricted snd_pcm_format_t [usertype] format
fsl_qmc_audio.c:389:59: got unsigned int [assigned] i
fsl_qmc_audio.c:564:26: warning: restricted snd_pcm_format_t degrades to integer
fsl_qmc_audio.c:569:50: warning: incorrect type in argument 1 (different base types)
fsl_qmc_audio.c:569:50: expected restricted snd_pcm_format_t [usertype] format
fsl_qmc_audio.c:569:50: got int [assigned] i
fsl_qmc_audio.c:573:62: warning: incorrect type in argument 1 (different base types)
fsl_qmc_audio.c:573:62: expected restricted snd_pcm_format_t [usertype] format
fsl_qmc_audio.c:573:62: got int [assigned] i
These warnings are due to snd_pcm_format_t values handling done in the
driver. Some macros and functions exist to handle safely these values.
Use dedicated macros and functions to remove these warnings.
Despite its name, the regulator vcc3v3_pcie30x1 has nothing to do with
pcie30x1. Instead, it supply power to VBAT1-5 on the M.2 KEY B port as
seen on page 8 of the schematic [1].
pcie30x1 is used for the mini PCIe slot, and as seen on page 9 the
vcc3v3_minipcie regulator is instead related to pcie30x1.
The M.2 KEY B port can be used for WWAN USB2 modules or SATA drives.
Use correct regulator vcc3v3_minipcie for pcie30x1.
WARNING: min() should probably be min_t(size_t, size, sizeof(ip))
+ ret = copy_to_user(out, &ip, min((size_t)size, sizeof(ip)));
And other style fixes:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Missing a blank line after declarations
Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6cae7 ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f50a ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
The DRM DP code has macros for the DP power sequencing commands. Use
them in the anx7625 driver instead of raw numbers.
Fixes: 548b512e144f ("drm/bridge: anx7625: send DPCD command to downstream") Fixes: 27f26359de9b ("drm/bridge: anx7625: Set downstream sink into normal status") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230710090929.1873646-1-wenst@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Visible glitches have been observed when running graphics applications on
Linux under Xen hypervisor. Those observations have been confirmed with
failures from kms_pwrite_crc Intel GPU test that verifies data coherency
of DRM frame buffer objects using hardware CRC checksums calculated by
display controllers, exposed to userspace via debugfs. Affected
processing paths have then been identified with new IGT test variants that
mmap the objects using different methods and caching modes [1].
When running as a Xen PV guest, Linux uses Xen provided PAT configuration
which is different from its native one. In particular, Xen specific PTE
encoding of write-combining caching, likely used by graphics applications,
differs from the Linux default one found among statically defined minimal
set of supported modes. Since Xen defines PTE encoding of the WC mode as
_PAGE_PAT, it no longer belongs to the minimal set, depends on correct
handling of _PAGE_PAT bit, and can be mismatched with write-back caching.
When a user calls mmap() for a DRM buffer object, DRM device specific
.mmap file operation, called from mmap_region(), takes care of setting PTE
encoding bits in a vm_page_prot field of an associated virtual memory area
structure. Unfortunately, _PAGE_PAT bit is not preserved when the vma's
.vm_flags are then applied to .vm_page_prot via vm_set_page_prot(). Bits
to be preserved are determined with _PAGE_CHG_MASK symbol that doesn't
cover _PAGE_PAT. As a consequence, WB caching is requested instead of WC
when running under Xen (also, WP is silently changed to WT, and UC
downgraded to UC_MINUS). When running on bare metal, WC is not affected,
but WP and WT extra modes are unintentionally replaced with WC and UC,
respectively.
WP and WT modes, encoded with _PAGE_PAT bit set, were introduced by commit 281d4078bec3 ("x86: Make page cache mode a real type"). Care was taken
to extend _PAGE_CACHE_MASK symbol with that additional bit, but that
symbol has never been used for identification of bits preserved when
applying page protection flags. Support for all cache modes under Xen,
including the problematic WC mode, was then introduced by commit 47591df50512 ("xen: Support Xen pv-domains using PAT").
The issue needs to be fixed by including _PAGE_PAT bit into a bitmask used
by pgprot_modify() for selecting bits to be preserved. We can do that
either internally to pgprot_modify() (as initially proposed), or by making
_PAGE_PAT a part of _PAGE_CHG_MASK. If we go for the latter then, since
_PAGE_PAT is the same as _PAGE_PSE, we need to note that _HPAGE_CHG_MASK
-- a huge pmds' counterpart of _PAGE_CHG_MASK, introduced by commit c489f1257b8c ("thp: add pmd_modify"), defined as (_PAGE_CHG_MASK |
_PAGE_PSE) -- will no longer differ from _PAGE_CHG_MASK. If such
modification of _PAGE_CHG_MASK was irrelevant to its users then one might
wonder why that new _HPAGE_CHG_MASK symbol was introduced instead of
reusing the existing one with that otherwise irrelevant bit (_PAGE_PSE in
that case) added.
Add _PAGE_PAT to _PAGE_CHG_MASK and _PAGE_PAT_LARGE to _HPAGE_CHG_MASK for
symmetry. Split out common bits from both symbols to a common symbol for
clarity.
[ dhansen: tweak the solution changelog description ]
Currently the write_cache attribute allows enabling the QUEUE_FLAG_WC
flag on devices that never claimed the capability.
Fix that by adding a QUEUE_FLAG_HW_WC flag that is set by
blk_queue_write_cache and guards re-enabling the cache through sysfs.
Note that any rescan that calls blk_queue_write_cache will still
re-enable the write cache as in the current code.
Fixes: 93e9d8e836cb ("block: add ability to flag write back caching on a device") Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20230707094239.107968-3-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
gpu->mmu_context is the MMU context of the last job in the HW queue, which
isn't necessarily the same as the context from the bad job. Dump the MMU
context from the scheduler determined bad submit to make it work as intended.
Fixes: 17e4660ae3d7 ("drm/etnaviv: implement per-process address spaces on MMUv2") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 70006300.serial: Couldn't get the reset
serial-tegra: probe of 70006300.serial failed with error -2
Commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit a63c0cd83720c
("arm64: dts: tegra: smaug: Add Bluetooth node") that enabled the HSUART
for the Pixel C. Fix this by populating the "reset-names" property for
the HSUART on the Pixel C.
Fixes: a63c0cd83720 ("arm64: dts: tegra: smaug: Add Bluetooth node") Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 3100000.serial: Couldn't get the reset
serial-tegra: probe of 3100000.serial failed with error -2
Commit 71de0a054d0e ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit ff578db7b693
("arm64: tegra: Enable UART instance on 40-pin header") that
enabled the HSUART for Jetson AGX Orin. Fix this by populating the
"reset-names" property for the HSUART on Jetson AGX Orin.
This fixes:
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-sck: False schema does not allow [[3, 21, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-miso: False schema does not allow [[3, 22, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-mosi: False schema does not allow [[3, 23, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: 'sck-gpios' is a required property
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: Unevaluated properties are not allowed ('gpio-miso', 'gpio-mosi', 'gpio-sck' were unexpected)
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#address-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#size-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
Two properties that need to be added later are "device_type" and
"ranges". Adding "device_type" on its own causes a new warning and the
value of "ranges" needs to be determined yet.
Such property simply doesn't exist (is not documented or used anywhere).
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: usb@d000: Unevaluated properties are not allowed ('#usb-cells' was unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
There is no such trigger documented or implemented in Linux. It was a
copy & paste mistake.
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: leds: led-wlan:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
'default-off' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
'default-off' does not match '^cpu[0-9]*$'
'default-off' does not match '^hci[0-9]+-power$'
'default-off' does not match '^mmc[0-9]+$'
'default-off' does not match '^phy[0-9]+tx$'
From schema: Documentation/devicetree/bindings/leds/leds-gpio.yaml
On 32-bit architectures comparing a resource against a value larger than
U32_MAX can cause a warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:1344:18: error: result of comparison of constant 4294967296 with expression of type 'resource_size_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
res->start > 0x100000000ull)
~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
As gcc does not warn about this in dead code, add an IS_ENABLED() check at
the start of the function. This will always return success but not actually resize
the BAR on 32-bit architectures without high memory, which is exactly what
we want here, as the driver can fall back to bank switching the VRAM
access.
Fixes: 31b8adab3247 ("drm/amdgpu: require a root bus window above 4GB for BAR resize") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled
mode during system suspend") aims to resolve issues with tisci
operations during system suspend operation. However, the system may
enter a no_irq stage in various other usage modes, including power-off
and restart. To determine if polling mode is appropriate, use the
system_state instead.
While at this, drop the unused is_suspending state variable and
related helpers.
Fixes: b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled mode during system suspend") Reported-by: Francesco Dolcini <francesco@dolcini.it> Reported-by: Wadim Egorov <w.egorov@phytec.de> Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Verdin AM62 Link: https://lore.kernel.org/r/20230620130329.4120443-1-nm@ti.com Closes: https://lore.kernel.org/all/ZGeHMjlnob2GFyHF@francesco-nb.int.toradex.com/ Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'664b9879f56e ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
The commit b2de43136058 ("arm64: dts: qcom: pmk8350: Add peripherals for
pmk8350") for the ADC TM (thermal monitoring device) have used the
compatible string from the vendor kernel ("qcom,adc-tm7"). Use the
proper compatible string that is defined in the upstream kernel
("qcom,spmi-adc-tm5-gen2").
The name of the thermal zone in pmr735b.dtsi (pmr735a-thermal) conflicts
with the thermal zone in pmr735a.dtsi. Rename the thermal zone according
to the chip name.
The name of the thermal zone in pm8350b.dtsi (pm8350c-thermal) conflicts
with the thermal zone in pm8350c.dtsi. Rename the thermal zone according
to the chip name.
The name of the thermal zone in pm8350.dtsi (pm8350c-thermal) conflicts
with the thermal zone in pm8350c.dtsi. Rename the thermal zone according
to the chip name.
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX203&206 DTSIs to better document the hardware.
Diff between 203 and 206:
pm8009_gpios
< "CAM_PWR_LD_EN",
> "NC",
pm8150_gpios
< "NC",
> "G_ASSIST_N",
< "WLC_EN_N", /* GPIO_10 */
> "NC", /* GPIO_10 */
Which is due to 5 II having an additional Google Assistant hardware
button and 1 II having a wireless charger & different camera wiring
to accommodate the additional 3D iToF sensor.
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX203&206 DTSIs to better document the hardware.
sm8250 faces the same problem with its Energy Model as sdm845. The energy
cost of LITTLE cores is reported to be higher than medium or big cores
EM computes the energy with formula:
energy = OPP's cost / maximum cpu capacity * utilization
On v6.4-rc6 we have:
max capacity of CPU0 = 284
capacity of CPU0's OPP(1612800 Hz) = 253
cost of CPU0's OPP(1612800 Hz) = 191704
max capacity of CPU4 = 871
capacity of CPU4's OPP(710400 Hz) = 255
cost of CPU4's OPP(710400 Hz) = 343217
Both OPPs have almost the same compute capacity but the estimated energy
per unit of utilization will be estimated to:
energy CPU0 = 191704 / 284 * 1 = 675
energy CPU4 = 343217 / 871 * 1 = 394
EM estimates that little CPU0 will consume 71% more than medium CPU4 for
the same compute capacity. According to [1], little consumes 25% less than
medium core for Coremark benchmark at those OPPs for the same duration.
Set the dynamic-power-coefficient of CPU0-3 to 105 to fix the energy model
for little CPUs.
projects / thirdparty / kernel / stable.git / log
