[WHY & HOW]
- Fix indexing phantom planes for mcache programming in the wrapper
- Fix phantom mcache allocations to align with HW guidance
- Fix mcache assignment for chroma plane for multi-planar formats
Reviewed-by: Austin Zheng <Austin.Zheng@amd.com> Signed-off-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
Some panels may not handle idle pattern properly during PSR entry.
[HOW]
Add a condition to allow multiple options on power down
sequence during PSR1 entry.
Reviewed-by: Anthony Koo <anthony.koo@amd.com> Signed-off-by: Martin Tsai <Martin.Tsai@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Setting link DPMS off in response to HPD disconnect creates AUX
transactions on a link that is supposed to be disconnected. This can
cause issues in some cases when the sink re-asserts HPD and expects
source to re-enable the link.
[How]
Avoid AUX transactions on disconnected link.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
currently dml2 is using a hard coded 16 to convert memclk to dram_speed_mts.
for apu, this depends on wck_ratio.
change to pass the already calculated dram_speed_mts from fpu to dml2.
v2: use existing calculation of dram_speed_mts for now to avoid regression
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Reviewed-by: Roman Li <Roman.Li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SDMA writes has to probe invalidate RW lines. Set snoop bit in mmhub for
this to happen.
v2: Missed a few mmhub_v9_4. Added now.
v3: Calculate hub offset once since it doesn't change inside the loop
Modified function names based on review comments.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Reviewed-by: Philip Yang <Philip.Yang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some ASICs L2 cache info may miss in kfd topology,
because the first bitmap may be empty, that means
the first cu may be inactive, so to find the first
active cu will solve the issue.
v2: Only find the first active cu in the first xcc
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's GPU page size not CPU page size. In most cases they
are the same, but not always. This can lead to overallocation
on systems with larger pages.
Cc: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Cc: Christian König <christian.koenig@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Additionally, while the names of the symbolic constants RESERVE_10 and
RELEASE_10 include the command length, the command length is not included
in the RESERVE and RELEASE names. Address both issues by renaming the
RESERVE and RELEASE constants into RESERVE_6 and RELEASE_6 respectively.
Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20250210205031.2970833-1-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Now for dwmac-loongson {tx,rx}_fifo_size are uninitialised, which means
zero. This means dwmac-loongson doesn't support changing MTU because in
stmmac_change_mtu() it requires the fifo size be no less than MTU. Thus,
set the correct tx_fifo_size and rx_fifo_size for it (16KB multiplied by
queue counts).
Here {tx,rx}_fifo_size is initialised with the initial value (also the
maximum value) of {tx,rx}_queues_to_use. So it will keep as 16KB if we
don't change the queue count, and will be larger than 16KB if we change
(decrease) the queue count. However stmmac_change_mtu() still work well
with current logic (MTU cannot be larger than 16KB for stmmac).
Note: the Fixes tag picked here is the oldest commit and key commit of
the dwmac-loongson series "stmmac: Add Loongson platform support".
Acked-by: Yanteng Si <si.yanteng@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Chong Qiao <qiaochong@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Link: https://patch.msgid.link/20250210134328.2755328-1-chenhuacai@loongson.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some users are reporting journal replay takes a long time when there is
excessive number of revoke blocks in the journal. Reported times are
like:
1048576 records - 95 seconds 2097152 records - 580 seconds
The problem is that hash chains in the revoke table gets excessively
long in these cases. Fix the problem by sizing the revoke table
appropriately before the revoke pass.
Thanks to Alexey Zhuravlev <azhuravlev@ddn.com> for benchmarking the
patch with large numbers of revoke blocks [1].
Frame shape and curr_dr_freq could be updated by sdw_compute_bus_params().
Peripherals will set curr_dr_freq as their frequency. Managers
should do the same. Then update frame shape according to the actual
bus frequency.
This code's intention is to configure lane0 and lane2 tunings, but for
lane2 there is a typo and it ends up tuning something else.
Fix the typo, as it doesn't appear to make sense to apply different
tunings for lane0 vs lane2.
The same typo appears to exist in the bootloader, hence we restore the
original value in the typo'd registers as well. This can be removed
once / if the bootloader is updated.
Note that this is incorrect in the downstream driver as well - the
values had been copied from there.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org> Tested-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: André Draszik <andre.draszik@linaro.org> Tested-by: Will McVicker <willmcvicker@google.com> Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-4-f5961268b149@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As reported by Damon Ding, the phy_get_mode() call doesn't work as
expected unless the PHY driver has a .set_mode() call. This prompts PHY
drivers to have empty stubs for .set_mode() for the sake of being able
to get the mode.
Make .set_mode() callback truly optional and update PHY's mode even if
it there is none.
According to the datasheet, setting the dig_clk_sel bit of CMN_REG(0097)
to 1'b1 selects LCPLL as the reference clock, while setting it to 1'b0
selects the ROPLL.
This function will synchronously cancel and wait for many display
work queue items, which might try to take the runtime pm reference
causing a bad deadlock. So, remove it from the runtime_pm suspend patch.
The Renesas RZ/G3S supports a power-saving mode where power to most of
the SoC components is lost, including the PIN controller. Save and
restore the pull-up/pull-down register contents to ensure the
functionality is preserved after a suspend/resume cycle.
The Renesas RZ/G3S supports a power saving mode where power to most of the
SoC components is turned off. When returning from this power saving mode,
SoC components need to be re-configured.
The SCIFs on the Renesas RZ/G3S need to be re-configured as well when
returning from this power saving mode. The sh-sci code already configures
the SCIF clocks, power domain and registers by calling uart_resume_port()
in sci_resume(). On suspend path the SCIF UART ports are suspended
accordingly (by calling uart_suspend_port() in sci_suspend()). The only
missing setting is the reset signal. For this assert/de-assert the reset
signal on driver suspend/resume.
In case the no_console_suspend is specified by the user, the registers need
to be saved on suspend path and restore on resume path. To do this the
sci_console_save()/sci_console_restore() functions were added. There is no
need to cache/restore the status or FIFO registers. Only the control
registers. The registers that will be saved/restored on suspend/resume are
specified by the struct sci_suspend_regs data structure.
The old default value for slice is 0.75 msec * (1 + ilog(ncpus)) which
means that we have a default slice of:
0.75 for 1 cpu
1.50 up to 3 cpus
2.25 up to 7 cpus
3.00 for 8 cpus and above.
For HZ=250 and HZ=100, because of the tick accuracy, the runtime of
tasks is far higher than their slice.
For HZ=1000 with 8 cpus or more, the accuracy of tick is already
satisfactory, but there is still an issue that tasks will get an extra
tick because the tick often arrives a little faster than expected. In
this case, the task can only wait until the next tick to consider that it
has reached its deadline, and will run 1ms longer.
There are two reasons for tick error: clockevent precision and the
CONFIG_IRQ_TIME_ACCOUNTING/CONFIG_PARAVIRT_TIME_ACCOUNTING. with
CONFIG_IRQ_TIME_ACCOUNTING every tick will be less than 1ms, but even
without it, because of clockevent precision, tick still often less than
1ms.
In order to make scheduling more precise, we changed 0.75 to 0.70,
Using 0.70 instead of 0.75 should not change much for other configs
and would fix this issue:
0.70 for 1 cpu
1.40 up to 3 cpus
2.10 up to 7 cpus
2.8 for 8 cpus and above.
This does not guarantee that tasks can run the slice time accurately
every time, but occasionally running an extra tick has little impact.
Signed-off-by: zihan zhou <15645113830zzh@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/20250208075322.13139-1-15645113830zzh@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The handoff between the boot stubs and start_secondary() are before IBT is
enabled and is definitely not subject to kCFI. As such, suppress all that for
this function.
Notably when the ENDBR poison would become fatal (ud1 instead of nop) this will
trigger a tripple fault because we haven't set up the IDT to handle #UD yet.
It is generally expected that the write() function should return a
positive value indicating the number of bytes written or a negative
error code if an error occurs. Returning 0 is unusual and can lead
to unexpected behavior.
When the user program writes the same value to wedged_mode twice in
a row, a lockup will occur, because the value expected to be
returned by the write() function inside the program should be equal
to the actual written value instead of 0.
To reproduce the issue:
echo 1 > /sys/kernel/debug/dri/0/wedged_mode
echo 1 > /sys/kernel/debug/dri/0/wedged_mode <- lockup here
Signed-off-by: Xin Wang <x.wang@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Fei Yang <fei.yang@intel.com> Cc: Shuicheng Lin <shuicheng.lin@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250213223615.2327367-1-x.wang@intel.com Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If regmap_read() fails, random stack value was used in calculating new
frequency in recalc_rate() callbacks. Such failure is really not
expected as these are all MMIO reads, however code should be here
correct and bail out. This also avoids possible warning on
uninitialized value.
It is required by firmware to wait up to 2 seconds for pending commands
before sending the destroy hardware context command. After 2 seconds
wait, if there are still pending commands, driver needs to cancel them.
So the context destroy steps need to be:
1. Stop drm scheduler. (drm_sched_entity_destroy)
2. Wait up to 2 seconds for pending commands.
3. Destroy hardware context and cancel the rest pending requests.
4. Wait all jobs associated with the hwctx are freed.
5. Free job resources.
There are some ipq5018 based device's firmware only can able to boot
arm32 but the clock driver dont allow it to be compiled on arm32.
Therefore allow GCC for IPQ5018 to be selected when building ARM32
kernel
GCC can see that the value range for "order" is capped, but this leads
it to consider that it might be negative, leading to a false positive
warning (with GCC 15 with -Warray-bounds -fdiagnostics-details):
../drivers/net/ethernet/mellanox/mlx4/alloc.c:691:47: error: array subscript -1 is below array bounds of 'long unsigned int *[2]' [-Werror=array-bounds=]
691 | i = find_first_bit(pgdir->bits[o], MLX4_DB_PER_PAGE >> o);
| ~~~~~~~~~~~^~~
'mlx4_alloc_db_from_pgdir': events 1-2
691 | i = find_first_bit(pgdir->bits[o], MLX4_DB_PER_PAGE >> o); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| | | | | (2) out of array bounds here
| (1) when the condition is evaluated to true In file included from ../drivers/net/ethernet/mellanox/mlx4/mlx4.h:53,
from ../drivers/net/ethernet/mellanox/mlx4/alloc.c:42:
../include/linux/mlx4/device.h:664:33: note: while referencing 'bits'
664 | unsigned long *bits[2];
| ^~~~
Switch the argument to unsigned int, which removes the compiler needing
to consider negative values.
NPAR (Network interface card partitioning)[1] 1.2 adds a transparent
VLAN tag for all packets between the NIC and the switch. Because of
that, RX VLAN acceleration cannot be supported for any additional
host configured VLANs. The driver has to acknowledge that it can
support no RX VLAN acceleration and set the NPAR 1.2 supported flag
when registering with the FW. Otherwise, the FW call will fail and
the driver will abort on these NPAR 1.2 NICs with this error:
The control handler wasn't freed if v4l2_fwnode_device_parse() failed. Do
that now.
Co-developed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Within the stm32_csi_start function, pm_runtime_put should
be called upon error following pm_runtime_get_sync.
Rework the function error handling by putting a label in
order to have common error handling for all calls requiring
pm_runtime_put.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memset the config argument to get_mbus_config V4L2 sub-device pad
operation to zero before calling the operation. This ensures the callers
don't need to bother with it nor the implementations need to set all
fields that may not be relevant to them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The datasheet for this sensor documents the minimum vblanking as being
32 lines. It does fix some problems with occasional black lines at the
bottom of images (tested on Raspberry Pi).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The indicated commit
* does not describe the problem that change tries to solve
* has programming issues
* introduces a bug: forever clears NETLBL_SECATTR_MLS_CAT
in (struct smack_known *)skp->smk_netlabel.flags
Reverting the commit to reapproach original problem
1) security/smack/smackfs.c`smk_set_cipso
does not clear NETLBL_SECATTR_MLS_CAT
from (struct smack_known *)skp->smk_netlabel.flags
on assigning CIPSO w/o categories:
2) security/smack/smack_lsm.c`smack_from_secattr
can not match skp->smk_netlabel with input packet's
struct netlbl_lsm_secattr *sap
because sap->flags have not NETLBL_SECATTR_MLS_CAT (what is correct)
but skp->smk_netlabel.flags have (what is incorrect):
| if ((sap->flags & NETLBL_SECATTR_MLS_CAT) == 0) {
| if ((skp->smk_netlabel.flags &
| NETLBL_SECATTR_MLS_CAT) == 0)
| found = 1;
| break;
| }
This commit sets/clears NETLBL_SECATTR_MLS_CAT in
skp->smk_netlabel.flags according to the presense of CIPSO categories.
The update of smk_netlabel is not atomic, so input packets processing
still may be incorrect during short time while update proceeds.
Cross case in pinctrl framework make impossible to an hogged pin and
another, not hogged, used within the same device-tree node. For example
with this simplified device-tree :
"pinctrl_pin_1" configuration is never set. This produces this path in
the code:
really_probe()
pinctrl_bind_pins()
| devm_pinctrl_get()
| pinctrl_get()
| create_pinctrl()
| pinctrl_dt_to_map()
| // Hog pin create an abort for all pins of the node
| ret = dt_to_map_one_config()
| | /* Do not defer probing of hogs (circular loop) */
| | if (np_pctldev == p->dev->of_node)
| | return -ENODEV;
| if (ret)
| goto err
|
call_driver_probe()
stm32_rtc_probe()
pinctrl_enable()
pinctrl_claim_hogs()
create_pinctrl()
for_each_maps(maps_node, i, map)
// Not hog pin is skipped
if (pctldev && strcmp(dev_name(pctldev->dev),
map->ctrl_dev_name))
continue;
At the first call of create_pinctrl() the hogged pin produces an abort to
avoid a defer of hogged pins. All other pin configurations are trashed.
At the second call, create_pinctrl is now called with pctldev parameter to
get hogs, but in this context only hogs are set. And other pins are
skipped.
To handle this, do not produce an abort in the first call of
create_pinctrl(). Classic pin configuration will be set in
pinctrl_bind_pins() context. And the hogged pin configuration will be set
in pinctrl_claim_hogs() context.
The ASoC convention is that clocks are removed after codec mute, and
power up/down is more about top level power management. For these chips,
the "mute" state still expects a TDM clock, and yanking the clock in
this state will trigger clock errors. So, do the full
shutdown<->mute<->active transition on the mute operation, so the amp is
in software shutdown by the time the clocks are removed.
This fixes TDM clock errors when streams are stopped.
Lower the volume if it is violating the platform maximum at its initial
value (i.e. at the time of the 'snd_soc_limit_volume' call).
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
[Cherry picked from the Asahi kernel with fixups -- broonie] Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://patch.msgid.link/20250208-asoc-volume-limit-v1-1-b98fcf4cdbad@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do all struct io_uring_params validation early on before allocating the
context. That makes initialisation easier, especially by having fewer
places where we need to care about partial de-initialisation.
Fpga get config status just returns status through ret_payload and there
is no need to allocate local buf and send its address through SMC args.
Moreover, the address that is being passed till now is linux virtual
address and is incorrect.
Corresponding modification has been done in the firmware to avoid using the
address sent by linux.
Currently it is assumed that the firmware doesn't present the host
partition in the list of partitions presented as part of the response
to PARTITION_INFO_GET from the firmware. However, there are few
platforms that prefer to present the same in the list of partitions.
It is not manadatory but not restricted as well.
So handle the same by making sure to check the presence of the host
VM ID in the XArray partition information maintained/managed in the
driver before attempting to add it.
When the firmware compatibility was handled previously in the commit 8e3f9da608f1 ("firmware: arm_ffa: Handle compatibility with different firmware versions"),
we only addressed firmware versions that have higher minor versions
compared to the driver version which is should be considered compatible
unless the firmware returns NOT_SUPPORTED.
However, if the firmware reports higher major version than the driver
supported, we need to reject it. If the firmware can work in a compatible
mode with the driver requested version, it must return the same major
version as requested.
Wrap the high temperature warning in a temperature event with
a call to net_ratelimit() to prevent flooding the kernel log
with repeated warning messages when temperature exceeds the
threshold multiple times within a short duration.
In the sensor_count field of the MTEWE register, bits 1-62 are
supported only for unmanaged switches, not for NICs, and bit 63
is reserved for internal use.
To prevent confusing output that may include set bits that are
not relevant to NIC sensors, we update the bitmask to retain only
the first bit, which corresponds to the sensor ASIC.
Currently, ctx_arg_info is read-only in the view of the verifier since
it is shared among programs of the same attach type. Make each program
have their own copy of ctx_arg_info so that we can use it to store
program specific information.
In the next patch where we support acquiring a referenced kptr through a
struct_ops argument tagged with "__ref", ctx_arg_info->ref_obj_id will
be used to store the unique reference object id of the argument. This
avoids creating a requirement in the verifier that "__ref" tagged
arguments must be the first set of references acquired [0].
The IMSIC driver assigns the IMSIC domain specific imsic_irq_set_affinity()
callback to the per device leaf MSI domain. That's a layering violation as
it is called with the leaf domain data and not with the IMSIC domain
data. This prevents moving the IMSIC driver to the common MSI library which
uses the generic msi_domain_set_affinity() callback for device MSI domains.
Instead of using imsic_irq_set_affinity() for leaf MSI domains, use
imsic_irq_set_affinity() for the non-leaf IMSIC base domain and use
irq_chip_set_affinity_parent() for leaf MSI domains.
Clang and GCC complain about overlapped initialisers in the
hrtimer_clock_to_base_table definition. With `make W=1` and CONFIG_WERROR=y
(which is default nowadays) this breaks the build:
CC kernel/time/hrtimer.o
kernel/time/hrtimer.c:124:21: error: initializer overrides prior initialization of this subobject [-Werror,-Winitializer-overrides]
124 | [CLOCK_REALTIME] = HRTIMER_BASE_REALTIME,
kernel/time/hrtimer.c:122:27: note: previous initialization is here
122 | [0 ... MAX_CLOCKS - 1] = HRTIMER_MAX_CLOCK_BASES,
(and similar for CLOCK_MONOTONIC, CLOCK_BOOTTIME, and CLOCK_TAI).
hrtimer_clockid_to_base(), which uses the table, is only used in
__hrtimer_init(), which is not a hotpath.
Therefore replace the table lookup with a switch case in
hrtimer_clockid_to_base() to avoid this warning.
exit_itimers() loops through every timer in the process to delete it. This
requires taking the system-wide hash_lock for each of these timers, and
contends with other processes trying to create or delete timers.
When a process creates hundreds of thousands of timers, and then exits
while other processes contend with it, this can trigger softlockups on
CONFIG_PREEMPT=n.
Add a cond_resched() invocation into the loop to allow the system to make
progress.
When a vxlan netdevice is brought up, if its default remote is a multicast
address, the device joins the indicated group.
Therefore when the multicast remote address changes, the device should
leave the current group and subscribe to the new one. Similarly when the
interface used for endpoint communication is changed in a situation when
multicast remote is configured. This is currently not done.
Both vxlan_igmp_join() and vxlan_igmp_leave() can however fail. So it is
possible that with such fix, the netdevice will end up in an inconsistent
situation where the old group is not joined anymore, but joining the new
group fails. Should we join the new group first, and leave the old one
second, we might end up in the opposite situation, where both groups are
joined. Undoing any of this during rollback is going to be similarly
problematic.
One solution would be to just forbid the change when the netdevice is up.
However in vnifilter mode, changing the group address is allowed, and these
problems are simply ignored (see vxlan_vni_update_group()):
# ip link add name br up type bridge vlan_filtering 1
# ip link add vx1 up master br type vxlan external vnifilter local 192.0.2.1 dev lo dstport 4789
# bridge vni add dev vx1 vni 200 group 224.0.0.1
# tcpdump -i lo &
# bridge vni add dev vx1 vni 200 group 224.0.0.2
18:55:46.523438 IP 0.0.0.0 > 224.0.0.22: igmp v3 report, 1 group record(s)
18:55:46.943447 IP 0.0.0.0 > 224.0.0.22: igmp v3 report, 1 group record(s)
# bridge vni
dev vni group/remote
vx1 200 224.0.0.2
Having two different modes of operation for conceptually the same interface
is silly, so in this patch, just do what the vnifilter code does and deal
with the errors by crossing fingers real hard.
The vnifilter code leaves old before joining new, and in case of join /
leave failures does not roll back the configuration changes that have
already been applied, but bails out of joining if it could not leave. Do
the same here: leave before join, apply changes unconditionally and do not
attempt to join if we couldn't leave.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the HED driver is built-in, it initializes after evged because they
both are at the same initcall level, so the initialization ordering
depends on the Makefile order. However, this prevents RAS records
coming in between the evged driver initialization and the HED driver
initialization from being handled.
If the number of such RAS records is above the APEI HEST error source
number, the HEST resources may be exhausted, and that may affect
subsequent RAS error reporting.
To fix this issue, change the initcall level of HED to subsys_initcall
and prevent the driver from being built as a module by changing ACPI_HED
in Kconfig from "tristate" to "bool".
Commit 903534fa7d30 ("PCI: Fix resource double counting on remove &
rescan") fixed double counting of mem resources because of old_size being
applied too early.
Fix a similar counting bug on the io resource side.
mlx4 doesn't support ndo_xdp_xmit / XDP_REDIRECT and wasn't
using page pool until now, so it could run XDP completions
in netpoll (NAPI budget == 0) just fine. Page pool has calling
context requirements, make sure we don't try to call it from
what is potentially HW IRQ context.
The bpf_verifier_state.loop_entry state should be copied by
copy_verifier_state(). Otherwise, .loop_entry values from unrelated
states would poison env->cur_state.
Additionally, env->stack should not contain any states with
.loop_entry != NULL. The states in env->stack are yet to be verified,
while .loop_entry is set for states that reached an equivalent state.
This means that env->cur_state->loop_entry should always be NULL after
pop_stack().
See the selftest in the next commit for an example of the program that
is not safe yet is accepted by verifier w/o this fix.
This change has some verification performance impact for selftests:
verifier.c:is_state_visited() uses RANGE_WITHIN states comparison rules
for cached states that have loop_entry with non-zero branches count
(meaning that loop_entry's verification is not yet done).
The RANGE_WITHIN rules in regsafe()/stacksafe() require register and
stack objects types to be identical in current and old states.
verifier.c:clean_live_states() replaces registers and stack spills
with NOT_INIT/STACK_INVALID marks, if these registers/stack spills are
not read in any child state. This means that clean_live_states() works
against loop convergence logic under some conditions. See selftest in
the next patch for a specific example.
Mitigate this by prohibiting clean_verifier_state() when
state->loop_entry->branches > 0.
This undoes negative verification performance impact of the
copy_verifier_state() fix from the previous patch.
Below is comparison between master and current patch.
Starting with commit c141ecc3cecd7 ("of: Warn when of_property_read_bool()
is used on non-boolean properties"), probing the gpcv2 device on i.MX8M
SoCs leads to warnings when LOCKDEP is enabled.
Fix this by checking property presence with of_property_present as
intended.
A single scatter-gather entry is limited by a 32 bits "length" field
that is practically 4GB - PAGE_SIZE. This means that even when the
memory is physically contiguous, we might need more than one entry to
represent it. Additionally when using dmabuf, the sg_table might be
originated outside the subsystem and optimized for other needs.
For instance an SGT of 16GB GPU continuous memory might look like this:
(a real life example)
Since ib_umem_find_best_pgsz works within SG entries, in the above case
we will result with the worst possible 4KB page size.
Fix this by taking into consideration only the alignment of addresses of
real discontinuity points rather than treating SG entries as such, and
adjust the page iterator to correctly handle cross SG entry pages.
There is currently an assumption that drivers do not ask for pages
bigger than maximal DMA size supported by their devices.
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock.
Don't try to operate on a drm_wb_connector as an amdgpu_dm_connector.
While dereferencing aconnector->base will "work" it's wrong and
might lead to unknown bad things. Just... don't.
Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reason to revert: idle power regression found in testing.
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Leo Zeng <Leo.Zeng@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The latest DP spec requires the DP TX to read DPCD F0000h through F0009h
when detecting LTTPR capabilities for the first time.
[How]
Update LTTPR cap retrieval to read up to F0009h (two more bytes than the
previous F0007h), and store the LTTPR ALPM capabilities.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: George Shen <george.shen@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
We should never apply a minimum dispclk value while in prepare_bandwidth
or while displays are active. This is always an optimization for when
all displays are disabled.
[How]
Defer dispclk optimization until safe_to_lower = true and display_count
reaches 0.
Since 0 has a special value in this logic (ie. no dispclk required)
we also need adjust the logic that clamps it for the actual request
to PMFW.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com> Reviewed-by: Leo Chen <leo.chen@amd.com> Reviewed-by: Syed Hassan <syed.hassan@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
eDP may not be connected to the GPU on driver start causing
fail enumeration.
[How]
Move the virtual signal type check before the eDP connector
signal check.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
RING_TIMESTAMP registers are inaccessible in VF mode.
Without drm-total-cycles-*, other keys provide little value.
Skip all optional "run_ticks" keys in this case.
Signed-off-by: Marcin Bernatowicz <marcin.bernatowicz@linux.intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com> Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250205191644.2550879-3-marcin.bernatowicz@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, there is only one "move" pointer in struct imsic_vector so
during vector movement the old vector points to the new vector and new
vector points to itself.
To support forced cleanup of the old vector, add separate "move_next" and
"move_prev" pointers to struct imsic_vector, where during vector movement
the "move_next" pointer of the old vector points to the new vector and the
"move_prev" pointer of the new vector points to the old vector.
Both "move_next" and "move_prev" pointers are cleared separately by
__imsic_local_sync() with a restriction that "move_prev" on the new
CPU is cleared only after the old CPU has cleared "move_next".
The netdevsim driver was experiencing NOHZ tick-stop errors during packet
transmission due to pending softirq work when calling napi_schedule().
This issue was observed when running the netconsole selftest, which
triggered the following error message:
NOHZ tick-stop error: local softirq work is pending, handler #08!!!
To fix this issue, introduce a timer that schedules napi_schedule()
from a timer context instead of calling it directly from the TX path.
Create an hrtimer for each queue and kick it from the TX path,
which then schedules napi_schedule() from the timer context.
Ensure the FIFO is empty before issuing the DAA command to prevent
incorrect command data from being sent. Align with other data transfers,
such as svc_i3c_master_start_xfer_locked(), which flushes the FIFO before
sending a command.
Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20250129162250.3629189-1-Frank.Li@nxp.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc-14 produces a bogus warning in some configurations:
drivers/edac/ie31200_edac.c: In function 'ie31200_probe1.isra':
drivers/edac/ie31200_edac.c:412:26: error: 'dimm_info' is used uninitialized [-Werror=uninitialized]
412 | struct dimm_data dimm_info[IE31200_CHANNELS][IE31200_DIMMS_PER_CHANNEL];
| ^~~~~~~~~
drivers/edac/ie31200_edac.c:412:26: note: 'dimm_info' declared here
412 | struct dimm_data dimm_info[IE31200_CHANNELS][IE31200_DIMMS_PER_CHANNEL];
| ^~~~~~~~~
I don't see any way the unintialized access could really happen here,
but I can see why the compiler gets confused by the two loops.
Instead, rework the two nested loops to only read the addr_decode
registers and then keep only one instance of the dimm info structure.
[Tony: Qiuxu pointed out that the "populate DIMM info" comment was left
behind in the refactor and suggested moving it. I deleted the comment
as unnecessry in front os a call to populate_dimm_info(). That seems
pretty self-describing.]
Allow a boolean property of "x-powers,no-thermistor" to specify devices
where the ts pin is not connected to anything. This works around an
issue found with some devices where the efuse is not programmed
correctly from the factory or when the register gets set erroneously.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Tested-by: Philippe Simons <simons.philippe@gmail.com> Link: https://lore.kernel.org/r/20250204155835.161973-4-macroalpha82@gmail.com Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
EHT MU PPDU contains user field of EHT-SIG field with STA-ID that
must match AID subfield in the Associate Response. Add a necessary
setting to prevent these from being inconsistent.
The sb_sel_ver is selection version for secure boot recorded in firmware
binary data, and its size is 4 and offset is 58 (not natural alignment).
Use get_unaligned_le32() to get this value safely. Find this by reviewing.
rtw_mac_power_switch() checks bit 8 of REG_SYS_STATUS1 to see if the
chip is powered on. This bit appears to be always on in the RTL8814AU,
so ignore it.
This function translates the rate number reported by the hardware into
something mac80211 can understand. It was ignoring the 3SS and 4SS HT
rates. Translate them too.
Also set *nss to 0 for the HT rates, just to make sure it's
initialised.
When an IOCTL times out and driver issues a target reset, if firmware
fails the task management elevate the recovery by issuing a diag reset to
controller.
In multi-cluster MIPS I6500 systems there is a GIC in each cluster,
each with its own counter. When a cluster powers up the counter will
be stopped, with the COUNTSTOP bit set in the GIC_CONFIG register.
In single cluster systems, it has been fine to clear COUNTSTOP once
in gic_clocksource_of_init() to start the counter. In multi-cluster
systems, this will only have started the counter in the boot cluster,
and any CPUs in other clusters will find their counter stopped which
will break the GIC clock_event_device.
Resolve this by having CPUs clear the COUNTSTOP bit when they come
online, using the existing gic_starting_cpu() CPU hotplug callback. This
will allow CPUs in secondary clusters to ensure that the cluster's GIC
counter is running as expected.
Signed-off-by: Paul Burton <paulburton@kernel.org> Signed-off-by: Chao-ying Fu <cfu@wavecomp.com> Signed-off-by: Dragan Mladjenovic <dragan.mladjenovic@syrmia.com> Signed-off-by: Aleksandar Rikalo <arikalo@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
