When the fixed regulators for the LCD panel and DP bridge were added,
their supplies were not modeled in. These, except for the 1.0V supply,
are just load switches, and need and have a supply.
Add the supplies for each of the fixed regulators.
Some of the regulator supplies for the MIPI-DPI-to-DP bridge and their
associated nodes are incorrectly named. In particular, the 1.0V supply
was modeled as a 1.2V supply.
Fix all the incorrect names, and also fix the voltage of the 1.0V
regulator.
Fix DTBS check errors for 'mt6358codec' and 'mt6358regulator':
Error message is:
pmic: 'mt6358codec' and 'mt6358regulator' does not match any of the
regexes: 'pinctrl-[0-9]+'.
Rename these two device node to generic 'audio-codec' and 'regulators'.
Fixes: 9f8872221674 ("arm64: dts: mt6358: add PMIC MT6358 related nodes") Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Link: https://lore.kernel.org/r/20241029064647.13370-1-macpaul.lin@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for the ADC on MT6357/8/9 and keep it default enabled
as this IP is always present on those PMICs.
Users may use different IIO channels depending on board-specific
routing.
Fix the issue where both 'output-low' and 'output-high' exist under GPIO
hog nodes (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
tree overlays. Since /delete-property/ is not supported in the overlays,
setting 'output-low' results in both properties being present. The
workaround is to disable these hogs and create new ones with 'output-low'
as needed.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
{'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
is valid under each of {'required': ['output-low']}, {'required': ['output-high']
Fixes: 3f6fc30abebc ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay") Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"#sound-dai-cells" is required if the board is using "simple-card".
However, the HiHope board uses "audio-graph", thus remove the unneeded
`#sound-dai-cells`.
Commit 9e72606cd2db ("arm64: dts: renesas: #sound-dai-cells is used when
simple-card") updated the comment regarding usage of "#sound-dai-cells"
in the SoC DTSI but missed to remove "#sound-dai-cells" from board DTS
files.
Lockdep gives a false positive splat as it can't distinguish the lock
which is taken by different IRQ descriptors from different IRQ chips
that are organized in a way of a hierarchy:
======================================================
WARNING: possible circular locking dependency detected 6.12.0-rc5-next-20241101-00148-g9fabf8160b53 #562 Tainted: G W
------------------------------------------------------
modprobe/141 is trying to acquire lock: ffff899446947868 (intel_soc_pmic_bxtwc:502:(&bxtwc_regmap_config)->lock){+.+.}-{4:4}, at: regmap_update_bits_base+0x33/0x90
but task is already holding lock: ffff899446947c68 (&d->lock){+.+.}-{4:4}, at: __setup_irq+0x682/0x790
A shift-out-of-bounds issue was identified by UBSAN in the
tegra_qspi_fill_tx_fifo_from_client_txbuf() function.
UBSAN: shift-out-of-bounds in drivers/spi/spi-tegra210-quad.c:345:27
shift exponent 32 is too large for 32-bit type 'u32' (aka 'unsigned int')
Call trace:
tegra_qspi_start_cpu_based_transfer
The problem arises when shifting the contents of tx_buf left by 8 times
the value of i, which can exceed 4 and result in an exponent larger than
32 bits.
Resolve this by restrict the value of i to be less than 4, preventing
the shift operation from overflowing.
Signed-off-by: Breno Leitao <leitao@debian.org> Fixes: 921fc1838fb0 ("spi: tegra210-quad: Add support for Tegra210 QSPI controller") Link: https://patch.msgid.link/20241004125400.1791089-1-leitao@debian.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org> Suggested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Usama Arif <usamaarif642@gmail.com> Fixes: ac10be5cdbfa ("arm64: Use common of_kexec_alloc_and_setup_fdt()") Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both drivers use I/O port accesses without declaring a dependency on
CONFIG_HAS_IOPORT. For sbc8360_wdt this causes a compile error on UML
once inb()/outb() helpers become conditional.
For sbc7240_wdt this causes no such errors with UML because this driver
depends on both x86_32 and !UML. Nevertheless add HAS_IOPORT as
a dependency for both drivers to be explicit and drop the !UML
dependency for sbc7240_wdt as it is now redundant since UML implies no
HAS_IOPORT.
The clock IDs for multiple MCSPI instances across wakeup domain
in J721s2 are incorrect when compared with documentation [1]. Fix the
clock IDs to their appropriate values.
The clock IDs for multiple MCSPI instances across wakeup domain
in J721e are incorrect when compared with documentation [1]. Fix
the clock ids to their appropriate values.
The clock IDs for multiple MCSPI instances across wakeup as
well as main domain in J7200 are incorrect when compared with
documentation [1]. This results in kernel crashes when the said
instances are enabled. Fix the clock ids to their appropriate
values.
Commit 0d0a0b441346 ("arm64: dts: ti: k3-j7200: fix main pinmux
range") split the main_pmx0 into two nodes: main_pmx0 and main_pmx1
due to a non-addressable region, but incorrectly represented the
ranges. As a result, the memory map for the pinctrl is incorrect. Fix
this by introducing the correct ranges.
The ranges are taken from the J7200 TRM [1] (Table 5-695. CTRL_MMR0
Registers).
Padconfig starting addresses and ranges:
- 0 to 66: 0x11c000, 0x10c
- 68: 0x11c110, 0x004
- 71 to 73: 0x11c11c, 0x00c
- 89 to 90: 0x11c164, 0x008
The datasheet [2] doesn't contain PADCONFIG63 (Table 6-106. Pin
Multiplexing), but the pin is necessary for enabling the MMC1 CLKLP
pad loopback and should be included in the pinmux register map.
Due to the change in pinmux node addresses, change the pinmux node for
the USB0_DRVVBUS pin to main_pmx2. The offset has not changed since the
new main_pmx2 node has the same base address and range as the original
main_pmx1 node. All other pinmuxing done within J7200 dts or dtso files
only uses main_pmx0 which has not changed.
The DCDC5 voltage rail in the X-Powers AXP809 PMIC has a resolution of
50mV, so the currently enforced limits of 1.475 and 1.525 volts cannot
be set, when the existing regulator value is beyond this range.
This will lead to the whole regulator driver to give up and fail
probing, which in turn will hang the system, as essential devices depend
on the PMIC.
In this case a bug in U-Boot set the voltage to 1.75V (meant for DCDC4),
and the AXP driver's attempt to correct this lead to this error:
==================
[ 4.447653] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
[ 4.450066] vcc-dram: Bringing 1750000uV into 1575000-1575000uV
[ 4.460272] vcc-dram: failed to apply 1575000-1575000uV constraint: -EINVAL
[ 4.474788] axp20x-regulator axp20x-regulator.0: Failed to register dcdc5
[ 4.482276] axp20x-regulator axp20x-regulator.0: probe with driver axp20x-regulator failed with error -22
==================
Set the limits to values that can be programmed, so any correction will
be successful.
Implement workaround for ERR051198
(https://www.nxp.com/docs/en/errata/IMX8MN_0N14Y.pdf)
PWM output may not function correctly if the FIFO is empty when a new SAR
value is programmed.
Description:
When the PWM FIFO is empty, a new value programmed to the PWM Sample
register (PWM_PWMSAR) will be directly applied even if the current timer
period has not expired. If the new SAMPLE value programmed in the
PWM_PWMSAR register is less than the previous value, and the PWM counter
register (PWM_PWMCNR) that contains the current COUNT value is greater
than the new programmed SAMPLE value, the current period will not flip
the level. This may result in an output pulse with a duty cycle of 100%.
Workaround:
Program the current SAMPLE value in the PWM_PWMSAR register before
updating the new duty cycle to the SAMPLE value in the PWM_PWMSAR
register. This will ensure that the new SAMPLE value is modified during
a non-empty FIFO, and can be successfully updated after the period
expires.
Write the old SAR value before updating the new duty cycle to SAR. This
avoids writing the new value into an empty FIFO.
This only resolves the issue when the PWM period is longer than 2us
(or <500kHz) because write register is not quick enough when PWM period is
very short.
Reproduce steps:
cd /sys/class/pwm/pwmchip1/pwm0
echo 2000000000 > period # It is easy to observe by using long period
echo 1000000000 > duty_cycle
echo 1 > enable
echo 8000 > duty_cycle # One full high pulse will be seen by scope
Fixes: 166091b1894d ("[ARM] MXC: add pwm driver for i.MX SoCs") Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20241008194123.1943141-1-Frank.Li@nxp.com Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'enable-active-low' property is not a valid, because it is the
default behaviour of the fixed regulator.
Only 'enable-active-high' is valid, and when this property is absent
the fixed regulator will act as active low by default.
Both the rk3588-orange-pi-5 and the Wolfvision pf5 io expander overlay
smuggled those enable-active-low properties in, so remove them to
make dtbscheck happier.
This driver uses various OF-specific functions and depends on phandle
parsing. There's no reason to make it available to non-OF systems so add
a relevant dependency switch to its Kconfig entry.
Fixes: 2f1630f437df ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets") Link: https://lore.kernel.org/r/20241004130449.51725-1-brgl@bgdev.pl Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rk808-regulator driver supports multiple PMIC variants from the Rockckip
RK80x and RK81x series, but the DVS GPIOs are supported on the RK808 variant
only, according to the DT bindings [1][2][3][4][5][6] and the datasheets for
the supported PMIC variants. [7][8][9][10][11][12]
Thus, change the probe path so the "dvs-gpios" property is checked for and
its value possibly used only when the handled PMIC variant is RK808. There's
no point in doing that on the other PMIC variants, because they don't support
the DVS GPIOs, and it goes against the DT bindings to allow a possible out-
of-place "dvs-gpios" property to actually be handled in the driver.
This eliminates the following messages, emitted when the "dvs-gpios" property
isn't found in the DT, from the kernel log on boards that actually don't use
the RK808 variant, which may have provided a source of confusion:
rk808-regulator rk808-regulator.2.auto: there is no dvs0 gpio
rk808-regulator rk808-regulator.2.auto: there is no dvs1 gpio
Furthermore, demote these kernel messages to debug messages, because they are
useful during the board bringup phase only. Emitting them afterwards, on the
boards that use the RK808 variant, but actually don't use the DVS0/1 GPIOs,
clutters the kernel log a bit, while they provide no value and may actually
cause false impression that some PMIC-related issues are present.
Only cgroup v2 can be attached by bpf programs, so this patch introduces
that cgroup_bpf_inherit and cgroup_bpf_offline can only be called in
cgroup v2, and this can fix the memleak mentioned by commit 04f8ef5643bc
("cgroup: Fix memory leak caused by missing cgroup_bpf_offline"), which
has been reverted.
Fixes: 2b0d3d3e4fcf ("percpu_ref: reduce memory footprint of percpu_ref in fast path") Fixes: 4bfc0bb2c60e ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself") Link: https://lore.kernel.org/cgroups/aka2hk5jsel5zomucpwlxsej6iwnfw4qu5jkrmjhyfhesjlfdw@46zxhg5bdnr7/ Signed-off-by: Chen Ridong <chenridong@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only cgroup v2 can be attached by cgroup by BPF programs. Revert this
commit and cgroup_bpf_inherit and cgroup_bpf_offline won't be called in
cgroup v1. The memory leak issue will be fixed with next patch.
The RT5682i and RT5682s drivers describe two DAIs: AIF1 supports both
playback and capture, while AIF2 supports capture only.
Cherry doesn't specify which DAI to use. Although this doesn't cause
real issues because AIF1 happens to be the first DAI, it should be
corrected:
codec@1a: #sound-dai-cells: 1 was expected
Update #sound-dai-cells to 1 and adjust DAI link usages accordingly.
Fixes: 87728e3ccf35 ("arm64: dts: mediatek: mt8195-cherry: Specify sound DAI links and routing") Signed-off-by: Fei Shao <fshao@chromium.org> Link: https://lore.kernel.org/r/20241021114318.1358681-1-fshao@chromium.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The T-PHY controller at 0x11e40000 controls two underlying USB2 and USB3
PHY ports. The USB3 port works normally just like the others, so there's
no point in disabling it separately. Otherwise, board DTs would have to
enable both the T-PHY controller and one of its sub-nodes in particular,
which is slightly redundant and confusing.
Remove the status line in the u3port1 node, so it's ready to be used
once the T-PHY controller is enabled.
Fixes: 9461e0caac9e ("arm64: dts: Add MediaTek MT8188 dts and evaluation board and Makefile") Signed-off-by: Fei Shao <fshao@chromium.org> Link: https://lore.kernel.org/r/20241021081311.543625-1-fshao@chromium.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Hana device has a second source option trackpad, but it is missing
its regulator supply. It only works because the regulator is marked as
always-on.
Add the regulator supply, but leave out the post-power-on delay. Instead,
document the post-power-on delay along with the reason for not adding
it in a comment.
Fixes: 689b937bedde ("arm64: dts: mediatek: add mt8173 elm and hana board") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241018082001.1296963-1-wenst@chromium.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function ub960_rxport_read is being called and afterwards ret is
being checked for any failures, however ret is not being assigned to
the return of the function call. Fix this by assigning ret to the
return of the call which appears to be missing.
Fixes: afe267f2d368 ("media: i2c: add DS90UB960 driver") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
efi_convert_cmdline() always returns a size of at least 1 because it
counts the NUL terminator, so the "cmdline_size == 0" condition is never
satisfied.
Change it to check if the string starts with a NUL character to get the
intended behavior: to use CONFIG_CMDLINE when load_options_size == 0.
Fixes: 60f38de7a8d4 ("efi/libstub: Unify command line param parsing") Signed-off-by: Jonathan Marek <jonathan@marek.ca> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit 53c98e35dcbc ("openrisc: mm: remove unneeded early ioremap
code") it was commented that early ioremap was not used in OpenRISC. I
acked this but was wrong, earlycon was using it. Earlycon setup now
fails with the below trace:
To fix this we could either implement early_ioremap again or implement
fixmap. In this patch we choose the later option of implementing basic
fixmap support.
While fixing this we also remove the old FIX_IOREMAP slots that were
used by early ioremap code. That code was also removed by commit 53c98e35dcbc ("openrisc: mm: remove unneeded early ioremap code") but
these definitions were not cleaned up.
The section counter tracks how many sections of kernel-doc were added.
The only real use of the counter value is to check if anything was
actually supposed to be output and give a warning is nothing is
available.
The current logic of remembering the initial value and then resetting
the value then when processing each file means that if a file has the
same number of sections as the previously processed one, a warning is
incorrectly given.
GCC 13 complains about the truncated output of snprintf():
drivers/mmc/host/mmc_spi.c: In function ‘mmc_spi_response_get’:
drivers/mmc/host/mmc_spi.c:227:64: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^
drivers/mmc/host/mmc_spi.c:227:9: note: ‘snprintf’ output between 26 and 43 bytes into a destination of size 32
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
228 | cmd->opcode, maptype(cmd));
Drop it and fold the string it generates into the only place where it's
emitted - the dev_dbg() call at the end of the function.
Add the atmel,usart-mode property to the UART nodes. This ensures
compliance with the atmel,at91-usart.yaml schema and resolves the errors
below:
serial@200: $nodename:0: 'serial@200' does not match
'^spi(@.*|-([0-9]|[1-9][0-9]+))?$'
serial@200: atmel,use-dma-rx: False schema does not allow True
serial@200: atmel,use-dma-tx: False schema does not allow True
serial@200: atmel,fifo-size: False schema does not allow [[16]]
These errors indicate that the property
atmel,usart-mode = <AT91_USART_MODE_SERIAL> is missing for
UART nodes 0, 1, 2, 3, 4, 6, 7, 8, 9, 10, 11, and 12.
Fixes: 99c808335877 ("ARM: dts: at91: sam9x60: Add missing flexcom definitions") Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Andrei Simion <andrei.simion@microchip.com> Link: https://lore.kernel.org/r/20240912093307.40488-1-andrei.simion@microchip.com
[claudiu.beznea: move the atmel,usart-mode close to vendor specific
properties to cope with DTS coding style] Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev> Signed-off-by: Sasha Levin <sashal@kernel.org>
L10A, being a fixed regulator, should have min_voltage = max_voltage,
otherwise fixed rulator fails to probe. Fix the max_voltage range to be
equal to minimum.
This loop is supposed to break if the frequency returned from
clk_round_rate() is the same as on the previous iteration. However,
that check doesn't make sense on the first iteration through the loop.
It leads to reading before the start of these->clk_perf_tbl[] array.
If request_irq() fails in sr_late_init(), there is no need to enable
the irq, and if it succeeds, disable_irq() after request_irq() still has
a time gap in which interrupts can come.
request_irq() with IRQF_NO_AUTOEN flag will disable IRQ auto-enable when
request IRQ.
The mutex node in mt8195.dtsi was triggering a dtbs_check error:
mutex@1c101000: 'clock-names', 'reg-names' do not match any of the
regexes: 'pinctrl-[0-9]+'
This seems no need by inspecting the DT schemas and other reference boards,
so drop 'clock-names' and 'reg-names' in mt8195.dtsi.
Fixes: 92d2c23dc269 ("arm64: dts: mt8195: add display node for vdosys1") Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241002051620.2050-4-macpaul.lin@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ethernet-phy node in mt8395-genio-1200-evk.dts was triggering a
dtbs_check error. The error message was:
eth-phy0@1: $nodename:0: 'eth-phy0@1' does not match
'^ethernet-phy(@[a-f0-9]+)?$'
Fix this issue by replacing 'eth-phy' node to generic 'ethernet-phy'.
Fixes: f2b543a191b6 ("arm64: dts: mediatek: add device-tree for Genio 1200 EVK board") Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241002051620.2050-3-macpaul.lin@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The clock index "CLK_APMIXED_MFGPLL" belongs to the "apmixedsys" provider,
so fix the index.
In addition, add a "mfg1" label so following commits could set
domain-supply for MFG1 power domain.
Fixes: eaf73e4224a3 ("arm64: dts: mediatek: mt8188: Add support for SoC power domains") Signed-off-by: Pablo Sun <pablo.sun@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241002022138.29241-2-pablo.sun@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When TMR_MANAGER is enabled as module there is a need to export functions
which are present in architecture code.
It has been found by running:
make W=1 C=1 allmodconfig
sed -i -e 's/WERROR=y/WERROR=n/g' .config
make C=1 W=1
which errors out like this:
ERROR: modpost: "xmb_manager_register" [drivers/misc/xilinx_tmr_manager.ko] undefined!
ERROR: modpost: "xmb_inject_err" [drivers/misc/xilinx_tmr_inject.ko] undefined!
If we fail to allocate memory for cb_data by kmalloc, the memory
allocation for eve_data is never freed, add the missing kfree()
in the error handling path.
Fixes: 05e5ba40ea7a ("driver: soc: xilinx: Add support of multiple callbacks for same event in event management driver") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20240706065155.452764-1-cuigaosheng1@huawei.com Signed-off-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 9728fb3ce117 ("spi: lpspi: disable lpspi module irq in DMA mode") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Link: https://patch.msgid.link/20240906022828.891812-1-ruanjinjie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_compatible_node() increments the node's refcount, and it must be
decremented again with a call to of_node_put() when the pointer is no
longer required to avoid leaking the resource.
Instead of adding the missing calls to of_node_put() in all execution
paths, use the cleanup attribute for 'arm_timer' by means of the
__free() macro, which automatically calls of_node_put() when the
variable goes out of scope.
The sp804 is currently only user selectable if COMPILE_TEST, this was
done by commit dfc82faad725 ("clocksource/drivers/sp804: Add
COMPILE_TEST to CONFIG_ARM_TIMER_SP804") in order to avoid it being
spuriously offered on platforms that won't have the hardware since it's
generally only seen on Arm based platforms. This config is overly
restrictive, while platforms that rely on the SP804 do select it in
their Kconfig there are others such as the Arm fast models which have a
SP804 available but currently unused by Linux. Relax the dependency to
allow it to be user selectable on arm and arm64 to avoid surprises and
in case someone comes up with a use for extra timer hardware.
Fixes: dfc82faad725 ("clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804") Reported-by: Ross Burton <ross.burton@arm.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20241001-arm64-vexpress-sp804-v3-1-0a2d3f7883e4@kernel.org Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During testing of the preceding changes, I noticed that in some cases,
current->kcsan_ctx.in_flat_atomic remained true until task exit. This is
obviously wrong, because _all_ accesses for the given task will be
treated as atomic, resulting in false negatives i.e. missed data races.
Debugging led to fs/dcache.c, where we can see this usage of seqlock:
do {
seq = read_seqbegin(&rename_lock);
dentry = __d_lookup(parent, name);
if (dentry)
break;
} while (read_seqretry(&rename_lock, seq));
[...]
As can be seen, read_seqretry() is never called if dentry != NULL;
consequently, current->kcsan_ctx.in_flat_atomic will never be reset to
false by read_seqretry().
Give up on the wrong assumption of "assume closing read_seqretry()", and
rely on the already-present annotations in read_seqcount_begin/retry().
Fixes: 88ecd153be95 ("seqlock, kcsan: Add annotations for KCSAN") Signed-off-by: Marco Elver <elver@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20241104161910.780003-6-elver@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
While fuzzing an arm64 kernel, Alexander Potapenko reported:
| BUG: KCSAN: data-race in ktime_get_mono_fast_ns / timekeeping_update
|
| write to 0xffffffc082e74248 of 56 bytes by interrupt on cpu 0:
| update_fast_timekeeper kernel/time/timekeeping.c:430 [inline]
| timekeeping_update+0x1d8/0x2d8 kernel/time/timekeeping.c:768
| timekeeping_advance+0x9e8/0xb78 kernel/time/timekeeping.c:2344
| update_wall_time+0x18/0x38 kernel/time/timekeeping.c:2360
| [...]
|
| read to 0xffffffc082e74258 of 8 bytes by task 5260 on cpu 1:
| __ktime_get_fast_ns kernel/time/timekeeping.c:372 [inline]
| ktime_get_mono_fast_ns+0x88/0x174 kernel/time/timekeeping.c:489
| init_srcu_struct_fields+0x40c/0x530 kernel/rcu/srcutree.c:263
| init_srcu_struct+0x14/0x20 kernel/rcu/srcutree.c:311
| [...]
|
| value changed: 0x000002f875d33266 -> 0x000002f877416866
|
| Reported by Kernel Concurrency Sanitizer on:
| CPU: 1 UID: 0 PID: 5260 Comm: syz.2.7483 Not tainted 6.12.0-rc3-dirty #78
This is a false positive data race between a seqcount latch writer and a reader
accessing stale data. Since its introduction, KCSAN has never understood the
seqcount_latch interface (due to being unannotated).
Unlike the regular seqlock interface, the seqcount_latch interface for latch
writers never has had a well-defined critical section, making it difficult to
teach tooling where the critical section starts and ends.
Introduce an instrumentable (non-raw) seqcount_latch interface, with
which we can clearly denote writer critical sections. This both helps
readability and tooling like KCSAN to understand when the writer is done
updating all latch copies.
Fixes: 88ecd153be95 ("seqlock, kcsan: Add annotations for KCSAN") Reported-by: Alexander Potapenko <glider@google.com> Co-developed-by: "Peter Zijlstra (Intel)" <peterz@infradead.org> Signed-off-by: "Peter Zijlstra (Intel)" <peterz@infradead.org> Signed-off-by: Marco Elver <elver@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20241104161910.780003-4-elver@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
x86_32 __arch_{,try_}cmpxchg64_emu()() macros use CALL instruction
inside asm statement. Use ALT_OUTPUT_SP() macro to add required
dependence on %esp register.
Fixes: 79e1dd05d1a2 ("x86: Provide an alternative() based cmpxchg64()") Signed-off-by: Uros Bizjak <ubizjak@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20241103160954.3329-2-ubizjak@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The details about the handling of the "normal" values were moved
to the _msecs_to_jiffies() helpers in commit ca42aaf0c861 ("time:
Refactor msecs_to_jiffies"). However, the same commit still mentioned
__msecs_to_jiffies() in the added documentation.
Thus point to _msecs_to_jiffies() instead.
Fixes: ca42aaf0c861 ("time: Refactor msecs_to_jiffies") Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/all/20241025110141.157205-2-ojeda@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The documentation's intention is to compare msecs_to_jiffies() (first
sentence) with __msecs_to_jiffies() (second sentence), which is what the
original documentation did. One of the cleanups in commit f3cb80804b82
("time: Fix various kernel-doc problems") may have thought the paragraph
was talking about the latter since that is what it is being documented.
Thus revert that part of the change.
Fixes: f3cb80804b82 ("time: Fix various kernel-doc problems") Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/all/20241025110141.157205-1-ojeda@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Guard functions in local_lock.h are defined using DEFINE_GUARD() and
DEFINE_LOCK_GUARD_1() macros having lock type defined as pointer in
the percpu address space. The functions, defined by these macros
return value in generic address space, causing:
cleanup.h:157:18: error: return from pointer to non-enclosed address space
and
cleanup.h:214:18: error: return from pointer to non-enclosed address space
when strict percpu checks are enabled.
Add explicit casts to remove address space of the returned pointer.
Such commit assumed that only two symbols are relevant for the symbol
size calculation. However, this can lead to an incorrect symbol size
calculation when there are mapping symbols emitted by readelf.
For instance, when feeding 'update_irq_load_avg+0x1c/0x1c4', faddr2line
might need to process the following readelf lines:
The symbol size of 'update_irq_load_avg' should be calculated with the
address of 'sched_pelt_multiplier', after skipping the mapping symbols
seen in between. However, the offending commit cuts the list short and
faddr2line incorrectly assumes 'update_irq_load_avg' is the last symbol
in the section, resulting in:
$ scripts/faddr2line vmlinux update_irq_load_avg+0x1c/0x1c4
skipping update_irq_load_avg address at 0xffffffc0081cca4c due to size mismatch (0x1c4 != 0x3ff9a59988)
no match for update_irq_load_avg+0x1c/0x1c4
After reverting the commit the issue is resolved:
$ scripts/faddr2line vmlinux update_irq_load_avg+0x1c/0x1c4
update_irq_load_avg+0x1c/0x1c4:
cpu_of at kernel/sched/sched.h:1109
(inlined by) update_irq_load_avg at kernel/sched/pelt.c:481
Fixes: c02904f05ff8 ("scripts/faddr2line: Check only two symbols when calculating symbol size") Signed-off-by: Carlos Llamas <cmllamas@google.com> Acked-by: Will Deacon <will@kernel.org> Acked-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When arch_stack_walk_reliable() is called to unwind for newly forked
tasks, the return value is negative which means the call stack is
unreliable. This obviously does not meet expectations.
The root cause is that after commit 3aec4ecb3d1f ("x86: Rewrite
ret_from_fork() in C"), the 'ret_addr' of newly forked task is changed
to 'ret_from_fork_asm' (see copy_thread()), then at the start of the
unwind, it is incorrectly interprets not as a "signal" one because
'ret_from_fork' is still used to determine the initial "signal" (see
__unwind_start()). Then the address gets incorrectly decremented in the
call to orc_find() (see unwind_next_frame()) and resulting in the
incorrect ORC data.
To fix it, check 'ret_from_fork_asm' rather than 'ret_from_fork' in
__unwind_start().
The function thermal_genl_auto() does not free the allocated message
in the error path. Fix that by putting a out label and jump to it
which will free the message instead of directly returning an error.
Fixes: 47c4b0de080a ("tools/lib/thermal: Add a thermal library") Reported-by: Lukasz Luba <lukasz.luba@arm.com>\a Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Link: https://patch.msgid.link/20241024105938.1095358-1-daniel.lezcano@linaro.org
[ rjw: Fixed up the !msg error path, added Fixes tag ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The thermal netlink has been extended with more commands which require
an encoding with more information. The generic encoding function puts
the thermal zone id with the command name. It is the unique
parameters.
The next changes will provide more parameters to the command. Set the
scene for those new parameters by making the encoding function more
generic.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Link: https://patch.msgid.link/20241022155147.463475-4-daniel.lezcano@linaro.org Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 7569406e95f2 ("thermal/lib: Fix memory leak on error in thermal_genl_auto()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The checker complains about, we do not unlock the "fullstop_mutex"
mutex, in case of hitting below error path:
<snip>
...
if (WARN_ON_ONCE(jiffies_at_lazy_cb - jif_start < 2 * HZ)) {
pr_alert("ERROR: call_rcu() CBs are not being lazy as expected!\n");
WARN_ON_ONCE(1);
return -1;
^^^^^^^^^^
...
<snip>
it happens because "-1" is returned right away instead of
doing a proper unwinding.
Fix it by jumping to "unwind" label instead of returning -1.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Neeraj Upadhyay <Neeraj.Upadhyay@amd.com> Closes: https://lore.kernel.org/rcu/ZxfTrHuEGtgnOYWp@pc636/T/ Fixes: 084e04fff160 ("rcuscale: Add laziness and kfree tests") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ahash_init functions may return fails. The ahash_hmac_init should
not return ok when ahash_init returns error. For an example, ahash_init
will return -ENOMEM when allocation memory is error.
DIV_ROUND_CLOSEST() after kstrtoul() results in an overflow if a large
number such as 18446744073709551615 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
pmbus_write_smbalert_mask() ignores the errors if the chip can't set
smbalert mask the standard way. It is not necessarily a problem for the irq
support if the chip is otherwise properly setup but it may leave an
uncleared fault behind.
pmbus_core will pick the fault on the next register_check(). The register
check will fails regardless of the actual register support by the chip.
This leads to missing attributes or debugfs entries for chips that should
provide them.
We cannot rely on register_check() as PMBUS_SMBALERT_MASK may be read-only.
Unconditionally clear the page fault after setting PMBUS_SMBALERT_MASK to
avoid the problem.
KCSAN reports a data race when access the krcp->monitor_work.timer.expires
variable in the schedule_delayed_monitor_work() function:
<snip>
BUG: KCSAN: data-race in __mod_timer / kvfree_call_rcu
read to 0xffff888237d1cce8 of 8 bytes by task 10149 on cpu 1:
schedule_delayed_monitor_work kernel/rcu/tree.c:3520 [inline]
kvfree_call_rcu+0x3b8/0x510 kernel/rcu/tree.c:3839
trie_update_elem+0x47c/0x620 kernel/bpf/lpm_trie.c:441
bpf_map_update_value+0x324/0x350 kernel/bpf/syscall.c:203
generic_map_update_batch+0x401/0x520 kernel/bpf/syscall.c:1849
bpf_map_do_batch+0x28c/0x3f0 kernel/bpf/syscall.c:5143
__sys_bpf+0x2e5/0x7a0
__do_sys_bpf kernel/bpf/syscall.c:5741 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5739 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5739
x64_sys_call+0x2625/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:322
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xc9/0x1c0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
write to 0xffff888237d1cce8 of 8 bytes by task 56 on cpu 0:
__mod_timer+0x578/0x7f0 kernel/time/timer.c:1173
add_timer_global+0x51/0x70 kernel/time/timer.c:1330
__queue_delayed_work+0x127/0x1a0 kernel/workqueue.c:2523
queue_delayed_work_on+0xdf/0x190 kernel/workqueue.c:2552
queue_delayed_work include/linux/workqueue.h:677 [inline]
schedule_delayed_monitor_work kernel/rcu/tree.c:3525 [inline]
kfree_rcu_monitor+0x5e8/0x660 kernel/rcu/tree.c:3643
process_one_work kernel/workqueue.c:3229 [inline]
process_scheduled_works+0x483/0x9a0 kernel/workqueue.c:3310
worker_thread+0x51d/0x6f0 kernel/workqueue.c:3391
kthread+0x1d1/0x210 kernel/kthread.c:389
ret_from_fork+0x4b/0x60 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 UID: 0 PID: 56 Comm: kworker/u8:4 Not tainted 6.12.0-rc2-syzkaller-00050-g5b7c893ed5ed #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Workqueue: events_unbound kfree_rcu_monitor
<snip>
kfree_rcu_monitor() rearms the work if a "krcp" has to be still
offloaded and this is done without holding krcp->lock, whereas
the kvfree_call_rcu() holds it.
Fix it by acquiring the "krcp->lock" for kfree_rcu_monitor() so
both functions do not race anymore.
Ensure sugov_eas_rebuild_sd() is always called when sugov_init()
succeeds. The out goto initialized sugov without forcing the rebuild.
Previously the missing call to sugov_eas_rebuild_sd() could lead to EAS
not being enabled on boot when it should have been, because it requires
all policies to be controlled by schedutil while they might not have
been initialized yet.
Fixes: e7a1b32e43b1 ("cpufreq: Rebuild sched-domains when removing cpufreq driver") Signed-off-by: Christian Loehle <christian.loehle@arm.com> Link: https://patch.msgid.link/35e572d9-1152-406a-9e34-2525f7548af9@arm.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 320406cb60b6 ("crypto: inside-secure - Replace generic aes
with libaes") replaced crypto_alloc_cipher() with kmalloc(), but did not
modify the handling of the return value. When kmalloc() returns NULL,
PTR_ERR_OR_ZERO(NULL) returns 0, but in fact, the memory allocation has
failed, and -ENOMEM should be returned.
Fixes: 320406cb60b6 ("crypto: inside-secure - Replace generic aes with libaes") Signed-off-by: Li Huafei <lihuafei1@huawei.com> Acked-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The adf_init_aer() won't destroy device_reset_wq when alloc_workqueue()
for device_sriov_wq failed. Add destroy_workqueue for device_reset_wq to
fix this issue.
Fixes: 4469f9b23468 ("crypto: qat - re-enable sriov after pf reset") Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
During modprobe:
1. In igen6_probe(), igen6_pvt will be allocated with kzalloc()
2. In igen6_register_mci(), mci->pvt_info will point to
&igen6_pvt->imc[mc]
During rmmod:
1. In mci_release() in edac_mc.c, it will kfree(mci->pvt_info)
2. In igen6_remove(), it will kfree(igen6_pvt);
Fix this issue by setting mci->pvt_info to NULL to avoid the double
kfree.
Fixes: 10590a9d4f23 ("EDAC/igen6: Add EDAC driver for Intel client SoCs using IBECC") Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219360 Signed-off-by: Orange Kao <orange@aiven.io> Signed-off-by: Tony Luck <tony.luck@intel.com> Link: https://lore.kernel.org/r/20241104124237.124109-2-orange@aiven.io Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error indicating that the device needs to be reset is reported,
disable the error reporting before device reset is complete,
enable the error reporting after the reset is complete to prevent
the same error from being reported repeatedly.
The amd-pstate driver sets CPPC_REQ.min_perf to CPPC_REQ.max_perf when
in active mode with performance governor. Typically CPPC_REQ.max_perf
is set to CPPC.highest_perf. This causes frequency throttling on
power-limited platforms which causes performance regressions on
certain classes of workloads.
Hence, set the CPPC_REQ.min_perf to the CPPC.nominal_perf or
CPPC_REQ.max_perf, whichever is lower of the two.
Fixes: ffa5096a7c33 ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors") Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20241021101836.9047-2-gautham.shenoy@amd.com Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When boost is changed the CPPC value is changed in amd_pstate_cpu_boost_update()
but then changed again when refresh_frequency_limits() and all it's callbacks
occur. The first is a pointless write, so instead just update the limits for
the policy and let the policy refresh anchor everything properly.
The while loop breaks in the first run because of incorrect
if condition. It also causes the statements after the if to
appear dead.
Fix this by changing the condition from if(timeout--) to
if(!timeout--).
This bug was reported by Coverity Scan.
Report:
CID 1600859: (#1 of 1): Logically dead code (DEADCODE)
dead_error_line: Execution cannot reach this statement: udelay(30UL);
Fixes: 9e2c7d99941d ("crypto: cavium - Add Support for Octeon-tx CPT Engine") Signed-off-by: Everest K.C. <everestkc@everestkc.com.np> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 8f4f68e788c3 ("crypto: pcrypt - Fix hungtask for
PADATA_RESET"), the pcrypt encryption and decryption operations return
-EAGAIN when the CPU goes online or offline. In alg_test(), a WARN is
generated when pcrypt_aead_decrypt() or pcrypt_aead_encrypt() returns
-EAGAIN, the unnecessary panic will occur when panic_on_warn set 1.
Fix this issue by calling crypto layer directly without parallelization
in that case.
Fixes: 8f4f68e788c3 ("crypto: pcrypt - Fix hungtask for PADATA_RESET") Signed-off-by: Yi Yang <yiyang13@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Granite Rapids CPUs with Flat2LM memory configurations may
mistakenly report near-memory errors as far-memory errors, resulting
in the invalid decoded ADXL results:
EDAC skx: Bad imc -1
Fix this incorrect far-memory error source indicator by prefetching the
decoded far-memory controller ID, and adjust the error source indicator
to near-memory if the far-memory controller ID is invalid.
Fixes: ba987eaaabf9 ("EDAC/i10nm: Add Intel Granite Rapids server support") Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Tested-by: Diego Garcia Rodriguez <diego.garcia.rodriguez@intel.com> Link: https://lore.kernel.org/r/20241015072236.24543-3-qiuxu.zhuo@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The current skx_common determines whether the memory error source is the
near memory of the 2LM system and then retrieves the decoded error results
from the ADXL components (near-memory vs. far-memory) accordingly.
However, some memory controllers may have limitations in correctly
reporting the memory error source, leading to the retrieval of incorrect
decoded parts from the ADXL.
To address these limitations, instead of simply determining whether the
memory error is from the near memory of the 2LM system, it is necessary to
distinguish the memory error source details as follows:
Memory error from the near memory of the 2LM system.
Memory error from the far memory of the 2LM system.
Memory error from the 1LM system.
Not a memory error.
This will enable the i10nm_edac driver to take appropriate actions for
those memory controllers that have limitations in reporting the memory
error source.
Fixes: ba987eaaabf9 ("EDAC/i10nm: Add Intel Granite Rapids server support") Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Tested-by: Diego Garcia Rodriguez <diego.garcia.rodriguez@intel.com> Link: https://lore.kernel.org/r/20241015072236.24543-2-qiuxu.zhuo@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix undefined behavior caused by left-shifting a negative value in the
expression:
cap_high ^ (1 << (bad_data_bit - 32))
The variable bad_data_bit ranges from 0 to 63. When it is less than 32,
bad_data_bit - 32 becomes negative, and left-shifting by a negative
value in C is undefined behavior.
Fix this by combining cap_high and cap_low into a 64-bit variable.
[ bp: Massage commit message, simplify error bits handling. ]
Fixes: ea2eb9a8b620 ("EDAC, fsl-ddr: Separate FSL DDR driver from MPC85xx") Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/r/20241016-imx95_edac-v3-3-86ae6fc2756a@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the registration of a thermal zone takes place at the time when
system suspend is started, thermal_pm_notify() can run before the new
thermal zone is added to thermal_tz_list and its "suspended" flag will
not be set. Consequently, if __thermal_zone_device_update() is called
for that thermal zone, it will not return early as expected which may
cause some destructive interference with the system suspend or resume
flow to occur.
To avoid that, make thermal_zone_init_complete() introduced previously
set the "suspended" flag for new thermal zones if it runs during system
suspend or resume.
Fixes: 4e814173a8c4 ("thermal: core: Fix thermal zone suspend-resume synchronization") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/8490245.NyiUUSuA9g@rjwysocki.net Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After thermal_zone_device_register_with_trips() has called
device_register() and it has registered the new thermal zone device
with the driver core, user space may access its sysfs attributes and,
among other things, it may enable the thermal zone before it is ready.
To address this, introduce a new thermal zone state flag for
initialization and set it before calling device_register() in
thermal_zone_device_register_with_trips(). This causes
__thermal_zone_device_update() to return early until the new flag
is cleared.
To clear it when the thermal zone is ready, introduce a new
function called thermal_zone_init_complete() that will also invoke
__thermal_zone_device_update() after clearing that flag (both under the
thernal zone lock) and make thermal_zone_device_register_with_trips()
call the new function instead of checking need_update and calling
thermal_zone_device_update() when it is set.
After this change, if user space enables the thermal zone prematurely,
__thermal_zone_device_update() will return early for it until
thermal_zone_init_complete() is called. In turn, if the thermal zone
is not enabled by user space before thermal_zone_init_complete() is
called, the __thermal_zone_device_update() call in it will return early
because the thermal zone has not been enabled yet, but that function
will be invoked again by thermal_zone_device_set_mode() when the thermal
zone is enabled and it will not return early this time.
The checking of need_update is not necessary any more because the
__thermal_zone_device_update() calls potentially triggered by cooling
device binding take place before calling thermal_zone_init_complete(),
so they all will return early, which means that
thermal_zone_init_complete() must call __thermal_zone_device_update()
in case the thermal zone is enabled prematurely by user space.
Fixes: 203d3d4aa482 ("the generic thermal sysfs driver") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/9360231.CDJkKcVGEf@rjwysocki.net Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of using two separate fields in struct thermal_zone_device for
representing flags related to thermal zone suspend, represent them
explicitly as bits in one u8 "state" field.
Subsequently, that field will be used for addressing race conditions
related to thermal zone initialization and exit.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/7733910.EvYhyI6sBW@rjwysocki.net Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Stable-dep-of: 7837fa8115e0 ("thermal: core: Mark thermal zones as initializing to start with") Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the code run for each thermal zone by the thermal PM notify
handler to separate functions.
This will help to make some subsequent changes look somewhat more
straightforward, among other things.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/2299090.iZASKD2KPV@rjwysocki.net Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Stable-dep-of: 7837fa8115e0 ("thermal: core: Mark thermal zones as initializing to start with") Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
