Each transfer can specify 8, 16 or 32 bits per word independently of
the default for the device being addressed. However, currently we
calculate the number of words in the frame assuming that the word size
is the device default.
If multiple transfers in the same message have differing
bits_per_word, we bitwise-or the different values in the WLEN register
field.
Fix both of these. Also rename 'frame_length' to 'frame_len_words' to
make clear that it's not a byte count like spi_message::frame_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain Intel Sunrisepoint PCH variants report zero chip selects in SPI
capabilities register even they have one per port. Detection in
pxa2xx_spi_probe() sets master->num_chipselect to 0 leading to -EINVAL
from spi_register_master() where chip select count is validated.
Fix this by not using SPI capabilities register on Sunrisepoint. They don't
have more than one chip select so use the default value 1 instead of
detection.
Fixes: 8b136baa5892 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals") Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HD-audio reconfig function got broken in the recent kernels,
typically resulting in a failure like:
snd_hda_intel 0000:00:1b.0: control 3:0:0:Playback Channel Map:0 is already present
This is because of the code restructuring to move the PCM and control
instantiation into the codec drive probe, by the commit [bcd96557bd0a:
ALSA: hda - Build PCMs and controls at codec driver probe]. Although
the commit above removed the calls of snd_hda_codec_build_pcms() and
*_build_controls() at the controller driver probe, the similar calls
in the reconfig were still left forgotten. This caused the
conflicting and duplicated PCMs and controls.
The fix is trivial: just remove these superfluous calls from
reconfig_codec().
Subwoofer does not work out of the box on ASUS N751/N551 laptops. This
patch fixes it. Patch tested on N751 laptop. N551 part is not tested,
but according to [1] and [2] this laptop requires similar changes, so I
included them in the patch.
Phoenix Audio MT202pcs (1de7:0114) and MT202exe (1de7:0013) need the
same workaround as TMX320 for avoiding the firmware bug. It fixes the
frequent error about the sample rate inquiries and the slow device
probe as consequence.
As akcipher uses an SG interface, you must not use vmalloc memory
as input for it. This patch fixes testmgr to copy the vmalloc
test vectors to kmalloc memory before running the test.
This patch also removes a superfluous sg_virt call in do_test_rsa.
The crypto hash walk code is broken when supplied with an offset
greater than or equal to PAGE_SIZE. This patch fixes it by adjusting
walk->pg and walk->offset when this happens.
This will provide fully accuracy to the mapcount calculation in the
write protect faults, so page pinning will not get broken by false
positive copy-on-writes.
total_mapcount() isn't the right calculation needed in
reuse_swap_page(), so this introduces a page_trans_huge_mapcount()
that is effectively the full accurate return value for page_mapcount()
if dealing with Transparent Hugepages, however we only use the
page_trans_huge_mapcount() during COW faults where it strictly needed,
due to its higher runtime cost.
This also provide at practical zero cost the total_mapcount
information which is needed to know if we can still relocate the page
anon_vma to the local vma. If page_trans_huge_mapcount() returns 1 we
can reuse the page no matter if it's a pte or a pmd_trans_huge
triggering the fault, but we can only relocate the page anon_vma to
the local vma->anon_vma if we're sure it's only this "vma" mapping the
whole THP physical range.
Kirill A. Shutemov discovered the problem with moving the page
anon_vma to the local vma->anon_vma in a previous version of this
patch and another problem in the way page_move_anon_rmap() was called.
Andrew Morton discovered that CONFIG_SWAP=n wouldn't build in a
previous version, because reuse_swap_page must be a macro to call
page_trans_huge_mapcount from swap.h, so this uses a macro again
instead of an inline function. With this change at least it's a less
dangerous usage than it was before, because "page" is used only once
now, while with the previous code reuse_swap_page(page++) would have
called page_mapcount on page+1 and it would have increased page twice
instead of just once.
Dean Luick noticed an uninitialized variable that could result in a
rmap inefficiency for the non-THP case in a previous version.
Mike Marciniszyn said:
: Our RDMA tests are seeing an issue with memory locking that bisects to
: commit 61f5d698cc97 ("mm: re-enable THP")
:
: The test program registers two rather large MRs (512M) and RDMA
: writes data to a passive peer using the first and RDMA reads it back
: into the second MR and compares that data. The sizes are chosen randomly
: between 0 and 1024 bytes.
:
: The test will get through a few (<= 4 iterations) and then gets a
: compare error.
:
: Tracing indicates the kernel logical addresses associated with the individual
: pages at registration ARE correct , the data in the "RDMA read response only"
: packets ARE correct.
:
: The "corruption" occurs when the packet crosse two pages that are not physically
: contiguous. The second page reads back as zero in the program.
:
: It looks like the user VA at the point of the compare error no longer points to
: the same physical address as was registered.
:
: This patch totally resolves the issue!
Link: http://lkml.kernel.org/r/1462547040-1737-2-git-send-email-aarcange@redhat.com Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: "Kirill A. Shutemov" <kirill@shutemov.name> Reviewed-by: Dean Luick <dean.luick@intel.com> Tested-by: Alex Williamson <alex.williamson@redhat.com> Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Tested-by: Josh Collier <josh.d.collier@intel.com> Cc: Marc Haber <mh+linux-kernel@zugschlus.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zs_can_compact() has two race conditions in its core calculation:
unsigned long obj_wasted = zs_stat_get(class, OBJ_ALLOCATED) -
zs_stat_get(class, OBJ_USED);
1) classes are not locked, so the numbers of allocated and used
objects can change by the concurrent ops happening on other CPUs
2) shrinker invokes it from preemptible context
Depending on the circumstances, thus, OBJ_ALLOCATED can become
less than OBJ_USED, which can result in either very high or
negative `total_scan' value calculated later in do_shrink_slab().
do_shrink_slab() has some logic to prevent those cases:
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-64
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
However, due to the way `total_scan' is calculated, not every
shrinker->count_objects() overflow can be spotted and handled.
To demonstrate the latter, I added some debugging code to do_shrink_slab()
(x86_64) and the results were:
Even though shrinker->count_objects() has returned an overflowed value,
the resulting `total_scan' is positive, and, what is more worrisome, it
is insanely huge. This value is getting used later on in
shrinker->scan_objects() loop:
while (total_scan >= batch_size ||
total_scan >= freeable) {
unsigned long ret;
unsigned long nr_to_scan = min(batch_size, total_scan);
shrinkctl->nr_to_scan = nr_to_scan;
ret = shrinker->scan_objects(shrinker, shrinkctl);
if (ret == SHRINK_STOP)
break;
freed += ret;
`total_scan >= batch_size' is true for a very-very long time and
'total_scan >= freeable' is also true for quite some time, because
`freeable < 0' and `total_scan' is large enough, for example, 22634041808232578. The only break condition, in the given scheme of
things, is shrinker->scan_objects() == SHRINK_STOP test, which is a
bit too weak to rely on, especially in heavy zsmalloc-usage scenarios.
To fix the issue, take a pool stat snapshot and use it instead of
racy zs_stat_get() calls.
Commit 702e5bc68ad2 ("ocfs2: use generic posix ACL infrastructure")
refactored code to use posix_acl_create. The problem with this function
is that it is not mindful of the cluster wide inode lock making it
unsuitable for use with ocfs2 inode creation with ACLs. For example,
when used in ocfs2_mknod, this function can cause deadlock as follows.
The parent dir inode lock is taken when calling posix_acl_create ->
get_acl -> ocfs2_iop_get_acl which takes the inode lock again. This can
cause deadlock if there is a blocked remote lock request waiting for the
lock to be downconverted. And same deadlock happened in ocfs2_reflink.
This fix is to revert back using ocfs2_init_acl.
Fixes: 702e5bc68ad2 ("ocfs2: use generic posix ACL infrastructure") Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com> Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 743b5f1434f5 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
introduced this issue. ocfs2_setattr called by chmod command holds
cluster wide inode lock when calling posix_acl_chmod. This latter
function in turn calls ocfs2_iop_get_acl and ocfs2_iop_set_acl. These
two are also called directly from vfs layer for getfacl/setfacl commands
and therefore acquire the cluster wide inode lock. If a remote
conversion request comes after the first inode lock in ocfs2_setattr,
OCFS2_LOCK_BLOCKED will be set. And this will cause the second call to
inode lock from the ocfs2_iop_get_acl() to block indefinetly.
The deleted version of ocfs2_acl_chmod() calls __posix_acl_chmod() which
does not call back into the filesystem. Therefore, we restore
ocfs2_acl_chmod(), modify it slightly for locking as needed, and use that
instead.
Fixes: 743b5f1434f5 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()") Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com> Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the very unlikely case __tcp_retransmit_skb() can not use the cloning
done in tcp_transmit_skb(), we need to refresh skb_mstamp before doing
the copy and transmit, otherwise TCP TS val will be an exact copy of
original transmit.
Fixes: 7faee5c0d514 ("tcp: remove TCP_SKB_CB(skb)->when") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reserved fields should be set to zero to avoid exposing
bits from the kernel stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stack object "dte_facilities" is allocated in x25_rx_call_request(),
which is supposed to be initialized in x25_negotiate_facilities.
However, 5 fields (8 bytes in total) are not initialized. This
object is then copied to userland via copy_to_user, thus infoleak
occurs.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
glibc's net/if.h contains copies of definitions from linux/if.h and these
conflict and cause build failures if both files are included by application
source code. Changes in uapi headers, which fixed header file dependencies to
include linux/if.h when it was needed, e.g. commit 1ffad83d, made the
net/if.h and linux/if.h incompatibilities visible as build failures for
userspace applications like iproute2 and xtables-addons.
This patch fixes compile errors when glibc net/if.h is included before
linux/if.h:
./linux/if.h:99:21: error: redeclaration of enumerator ‘IFF_NOARP’
./linux/if.h:98:23: error: redeclaration of enumerator ‘IFF_RUNNING’
./linux/if.h:97:26: error: redeclaration of enumerator ‘IFF_NOTRAILERS’
./linux/if.h:96:27: error: redeclaration of enumerator ‘IFF_POINTOPOINT’
./linux/if.h:95:24: error: redeclaration of enumerator ‘IFF_LOOPBACK’
./linux/if.h:94:21: error: redeclaration of enumerator ‘IFF_DEBUG’
./linux/if.h:93:25: error: redeclaration of enumerator ‘IFF_BROADCAST’
./linux/if.h:92:19: error: redeclaration of enumerator ‘IFF_UP’
./linux/if.h:252:8: error: redefinition of ‘struct ifconf’
./linux/if.h:203:8: error: redefinition of ‘struct ifreq’
./linux/if.h:169:8: error: redefinition of ‘struct ifmap’
./linux/if.h:107:23: error: redeclaration of enumerator ‘IFF_DYNAMIC’
./linux/if.h:106:25: error: redeclaration of enumerator ‘IFF_AUTOMEDIA’
./linux/if.h:105:23: error: redeclaration of enumerator ‘IFF_PORTSEL’
./linux/if.h:104:25: error: redeclaration of enumerator ‘IFF_MULTICAST’
./linux/if.h:103:21: error: redeclaration of enumerator ‘IFF_SLAVE’
./linux/if.h:102:22: error: redeclaration of enumerator ‘IFF_MASTER’
./linux/if.h:101:24: error: redeclaration of enumerator ‘IFF_ALLMULTI’
./linux/if.h:100:23: error: redeclaration of enumerator ‘IFF_PROMISC’
The cases where linux/if.h is included before net/if.h need a similar fix in
the glibc side, or the order of include files can be changed userspace
code as a workaround.
This change was tested in x86 userspace on Debian unstable with
scripts/headers_compile_test.sh:
$ make headers_install && \
cd usr/include && ../../scripts/headers_compile_test.sh -l -k
...
cc -Wall -c -nostdinc -I /usr/lib/gcc/i586-linux-gnu/5/include -I /usr/lib/gcc/i586-linux-gnu/5/include-fixed -I . -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH/i586-linux-gnu -o /dev/null ./linux/if.h_libc_before_kernel.h
PASSED libc before kernel test: ./linux/if.h
Reported-by: Jan Engelhardt <jengelh@inai.de> Reported-by: Josh Boyer <jwboyer@fedoraproject.org> Reported-by: Stephen Hemminger <shemming@brocade.com> Reported-by: Waldemar Brodkorb <mail@waldemar-brodkorb.de> Cc: Gabriel Laskar <gabriel@lse.epita.fr> Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the newly introduced helper functions the skb pulling is hidden
in the checksumming function - and undone before returning to the
caller.
The IGMP and MLD query parsing functions in the bridge still
assumed that the skb is pointing to the beginning of the IGMP/MLD
message while it is now kept at the beginning of the IPv4/6 header.
If there is a querier somewhere else, then this either causes
the multicast snooping to stay disabled even though it could be
enabled. Or, if we have the querier enabled too, then this can
create unnecessary IGMP / MLD query messages on the link.
Fixing this by taking the offset between IP and IGMP/MLD header into
account, too.
Fixes: 9afd85c9e455 ("net: Export IGMP/MLD message validation code") Reported-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_bridge_ifindices() is used from the old "deviceless" bridge ioctl
calls which aren't called with rtnl held. The comment above says that it is
called with rtnl but that is not really the case.
Here's a sample output from a test ASSERT_RTNL() which I put in
get_bridge_ifindices and executed "brctl show":
[ 957.422726] RTNL: assertion failed at net/bridge//br_ioctl.c (30)
[ 957.422925] CPU: 0 PID: 1862 Comm: brctl Tainted: G W O
4.6.0-rc4+ #157
[ 957.423009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.8.1-20150318_183358- 04/01/2014
[ 957.423009] 0000000000000000ffff880058adfdf0ffffffff8138dec5 0000000000000400
[ 957.423009] ffffffff81ce8380ffff880058adfe58ffffffffa05ead32 0000000000000001
[ 957.423009] 00007ffec1a444b00000000000000400ffff880053c19130 0000000000008940
[ 957.423009] Call Trace:
[ 957.423009] [<ffffffff8138dec5>] dump_stack+0x85/0xc0
[ 957.423009] [<ffffffffa05ead32>]
br_ioctl_deviceless_stub+0x212/0x2e0 [bridge]
[ 957.423009] [<ffffffff81515beb>] sock_ioctl+0x22b/0x290
[ 957.423009] [<ffffffff8126ba75>] do_vfs_ioctl+0x95/0x700
[ 957.423009] [<ffffffff8126c159>] SyS_ioctl+0x79/0x90
[ 957.423009] [<ffffffff8163a4c0>] entry_SYSCALL_64_fastpath+0x23/0xc1
Since it only reads bridge ifindices, we can use rcu to safely walk the net
device list. Also remove the wrong rtnl comment above.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The peer may be expecting a reply having sent a request and then done a
shutdown(SHUT_WR), so tearing down the whole socket at this point seems
wrong and breaks for me with a client which does a SHUT_WR.
Looking at other socket family's stream_recvmsg callbacks doing a shutdown
here does not seem to be the norm and removing it does not seem to have
had any adverse effects that I can see.
I'm using Stefan's RFC virtio transport patches, I'm unsure of the impact
on the vmci transport.
Signed-off-by: Ian Campbell <ian.campbell@docker.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Cc: Andy King <acking@vmware.com> Cc: Dmitry Torokhov <dtor@vmware.com> Cc: Jorgen Hansen <jhansen@vmware.com> Cc: Adit Ranadive <aditr@vmware.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use htons instead of unconditionally byte swapping nexthdr. On a little
endian systems shifting the byte is correct behavior, but it results in
incorrect csums on big endian architectures.
Fixes: f8c6455bb04b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE') Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Carol Soto <clsoto@us.ibm.com> Tested-by: Carol Soto <clsoto@us.ibm.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stack object “map” has a total size of 32 bytes. Its last 4
bytes are padding generated by compiler. These padding bytes are
not initialized and sent out via “nla_put”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stack object “info” has a total size of 12 bytes. Its last byte
is padding which is not initialized and leaked via “put_cmsg”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the receive path a queue's work bit was cleared unconditionally even
if fec_enet_rx_queue only read out a part of the available packets from
the hardware. This resulted in not reading any packets in the next napi
turn and so packets were delayed or lost.
The obvious fix is to only clear a queue's bit when the queue was
emptied.
Fixes: 4d494cdc92b3 ("net: fec: change data structure to support multiqueue") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Fugang Duan <fugang.duan@nxp.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handler 'ila_fill_encap_info' adds one attribute: ILA_ATTR_LOCATOR.
Fixes: 65d7ab8de582 ("net: Identifier Locator Addressing module") CC: Tom Herbert <tom@herbertland.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was recently reported to me, and reproduced on the latest net kernel,
when attempting to run netperf from a host that had a netem qdisc attached
to the egress interface:
The problem occurs because netem is not prepared to handle GSO packets (as it
uses skb_checksum_help in its enqueue path, which cannot manipulate these
frames).
The solution I think is to simply segment the skb in a simmilar fashion to the
way we do in __dev_queue_xmit (via validate_xmit_skb), with some minor changes.
When we decide to corrupt an skb, if the frame is GSO, we segment it, corrupt
the first segment, and enqueue the remaining ones.
tested successfully by myself on the latest net kernel, to which this applies
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Jamal Hadi Salim <jhs@mojatatu.com> CC: "David S. Miller" <davem@davemloft.net> CC: netem@lists.linux-foundation.org CC: eric.dumazet@gmail.com CC: stephen@networkplumber.org Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly, we need to update backlog too when we update qlen.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is we only count qlen for HTB qdisc but not backlog.
We need to update backlog too when we update qlen, so that we
can at least know the average packet length.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the bottom qdisc decides to, for example, drop some packet,
it calls qdisc_tree_decrease_qlen() to update the queue length
for all its ancestors, we need to update the backlog too to
keep the stats on root qdisc accurate.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove nearly duplicated code and prepare for the following patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iptunnel_pull_header expects that IP header was already pulled; with this
expectation, it pulls the tunnel header. This is not true in gre_err.
Furthermore, ipv4_update_pmtu and ipv4_redirect expect that skb->data points
to the IP header.
We cannot pull the tunnel header in this path. It's just a matter of not
calling iptunnel_pull_header - we don't need any of its effects.
Fixes: bda7bb463436 ("gre: Allow multiple protocol listener for gre protocol.") Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op
when !DEBUG") the implementation of net_dbg_ratelimited() was buggy
for both the DEBUG and CONFIG_DYNAMIC_DEBUG cases.
The bug was that net_ratelimit() was being called and, despite
returning true, nothing was being printed to the console. This
resulted in messages like the following -
"net_ratelimit: %d callbacks suppressed"
with no other output nearby.
After commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when
!DEBUG") the bug is fixed for the DEBUG case. However, there's no
output at all for CONFIG_DYNAMIC_DEBUG case.
This patch restores debug output (if enabled) for the
CONFIG_DYNAMIC_DEBUG case.
Add a definition of net_dbg_ratelimited() for the CONFIG_DYNAMIC_DEBUG
case. The implementation takes care to check that dynamic debugging is
enabled before calling net_ratelimit().
Fixes: d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") Signed-off-by: Tim Bingham <tbingham@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
llvm cannot always recognize memset as builtin function and optimize
it away, so just delete it. It was a leftover from testing
of bpf_perf_event_output() with large data structures.
Fixes: 39111695b1b8 ("samples: bpf: add bpf_perf_event_output example") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 35578d798400 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter")
introduced clever way to check bpf_helper<->map_type compatibility.
Later on commit a43eec304259 ("bpf: introduce bpf_perf_event_output() helper") adjusted
the logic and inadvertently broke it.
Get rid of the clever bool compare and go back to two-way check
from map and from helper perspective.
Fixes: a43eec304259 ("bpf: introduce bpf_perf_event_output() helper") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK,
the malicious application may overflow 32-bit bpf program refcnt.
It's also possible to overflow map refcnt on 1Tb system.
Impose 32k hard limit which means that the same bpf program or
map cannot be shared by more than 32k processes.
Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When bpf(BPF_PROG_LOAD, ...) was invoked with a BPF program whose bytecode
references a non-map file descriptor as a map file descriptor, the error
handling code called fdput() twice instead of once (in __bpf_map_get() and
in replace_map_fd_with_map_ptr()). If the file descriptor table of the
current task is shared, this causes f_count to be decremented too much,
allowing the struct file to be freed while it is still in use
(use-after-free). This can be exploited to gain root privileges by an
unprivileged user.
This bug was introduced in
commit 0246e64d9a5f ("bpf: handle pseudo BPF_LD_IMM64 insn"), but is only
exploitable since
commit 1be7f75d1668 ("bpf: enable non-root eBPF programs") because
previously, CAP_SYS_ADMIN was required to reach the vulnerable code.
(posted publicly according to request by maintainer)
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple skb are TX-completed in a row, we might incorrectly keep
a timestamp of a prior skb and cause extra work.
Fixes: ec693d47010e8 ("net/mlx4_en: Add HW timestamping (TS) support") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit fbd40ea0180a ("ipv4: Don't do expensive useless work
during inetdev destroy.") when deleting an interface,
fib_del_ifaddr() can be executed without any primary address
present on the dead interface.
The above is safe, but triggers some "bug: prim == NULL" warnings.
This commit avoids warning if the in_dev is dead
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minimum MTU that can be set in Connectx4 device is 68.
This fixes the case where a user wants to set invalid MTU,
the driver will fail to satisfy this request and the interface
will stay down.
It is better to report an error and continue working with old
mtu.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the error flow of adding flow rule to auto-grouped flow
table, we call to tree_remove_node.
tree_remove_node locks the node's parent, however the node's parent
is already locked by mlx5_add_flow_rule and this causes a deadlock.
After this patch, if we failed to add the flow rule, we unlock the
flow table before calling to tree_remove_node.
fixes: f0d22d187473 ('net/mlx5_core: Introduce flow steering autogrouped
flow table') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reported-by: Amir Vadai <amir@vadai.me> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using masked actions the ipv6_proto field of an action
to set IPv6 fields may be zero rather than the prevailing protocol
which will result in skipping checksum recalculation.
This patch resolves the problem by relying on the protocol
in the flow key rather than that in the set field action.
Fixes: 83d2b9ba1abc ("net: openvswitch: Support masked set actions.") Cc: Jarno Rajahalme <jrajahalme@nicira.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atl2 includes NETIF_F_SG in hw_features even though it has no support
for non-linear skbs. This bug was originally harmless since the
driver does not claim to implement checksum offload and that used to
be a requirement for SG.
Now that SG and checksum offload are independent features, if you
explicitly enable SG *and* use one of the rare protocols that can use
SG without checkusm offload, this potentially leaks sensitive
information (before you notice that it just isn't working). Therefore
this obscure bug has been designated CVE-2016-2117.
Reported-by: Justin Yackoski <jyackoski@crypto-nite.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: ec5f06156423 ("net: Kill link between CSUM and SG features.") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the IPv6 counterpart to commit 8282f27449bf ("inet: frag: Always
orphan skbs inside ip_defrag()").
Prior to commit 029f7f3b8701 ("netfilter: ipv6: nf_defrag: avoid/free
clone operations"), ipv6 fragments sent to nf_ct_frag6_gather() would be
cloned (implicitly orphaning) prior to queueing for reassembly. As such,
when the IPv6 message is eventually reassembled, the skb->sk for all
fragments would be NULL. After that commit was introduced, rather than
cloning, the original skbs were queued directly without orphaning. The
end result is that all frags except for the first and last may have a
socket attached.
This commit explicitly orphans such skbs during nf_ct_frag6_gather() to
prevent BUG_ON(skb->sk) during a later call to ip6_fragment().
When __vlan_insert_tag() fails from skb_vlan_push() path due to the
skb_cow_head(), we need to undo the __skb_push() in the error path
as well that was done earlier to move skb->data pointer to mac header.
Moreover, I noticed that when in the non-error path the __skb_pull()
is done and the original offset to mac header was non-zero, we fixup
from a wrong skb->data offset in the checksum complete processing.
So the skb_postpush_rcsum() really needs to be done before __skb_pull()
where skb->data still points to the mac header start and thus operates
under the same conditions as in __vlan_insert_tag().
Fixes: 93515d53b133 ("net: move vlan pop/push functions into common code") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace individual implementations with the recently introduced
skb_postpush_rcsum() helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Tom Herbert <tom@herbertland.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the SO_REUSEPORT socket option, it is possible to create sockets
in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
the AF_INET6 sockets.
Prior to the commits referenced below, an incoming IPv4 packet would
always be routed to a socket of type AF_INET when this mixed-mode was used.
After those changes, the same packet would be routed to the most recently
bound socket (if this happened to be an AF_INET6 socket, it would
have an IPv4 mapped IPv6 address).
The change in behavior occurred because the recent SO_REUSEPORT optimizations
short-circuit the socket scoring logic as soon as they find a match. They
did not take into account the scoring logic that favors AF_INET sockets
over AF_INET6 sockets in the event of a tie.
To fix this problem, this patch changes the insertion order of AF_INET
and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the
list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
the tail of the list. This will force AF_INET sockets to always be
considered first.
Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection") Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection") Reported-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: Craig Gallek <kraig@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have a positive report of another Huawei device needing
this quirk: The ME906s-158 (12d1:15c1). This is an m.2 form
factor modem with no obvious relationship to the E3372 (12d1:157d)
we already have a quirk entry for. This is reason enough to
believe the quirk might be necessary for any number of current
and future Huawei devices.
Applying the quirk to all Huawei devices, since it is crucial
to any device affected by the firmware bug, while the impact
on non-affected devices is negligible.
The quirk can if necessary be disabled per-device by writing
N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end
Reported-by: Andreas Fett <andreas.fett@secunet.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
verifier must check for reserved size bits in instruction opcode and
reject BPF_LD | BPF_ABS | BPF_DW and BPF_LD | BPF_IND | BPF_DW instructions,
otherwise interpreter will WARN_RATELIMIT on them during execution.
Fixes: ddd872bc3098 ("bpf: verifier: add checks for BPF_ABS | BPF_IND instructions") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A failure in validate_xmit_skb_list() triggered an unconditional call
to dev_requeue_skb with skb=NULL. This slowly grows the queue
discipline's qlen count until all traffic through the queue stops.
We take the optimistic approach and continue running the queue after a
failure since it is unknown if later packets also will fail in the
validate path.
Fixes: 55a93b3ea780 ("qdisc: validate skb without holding lock") Signed-off-by: Lars Persson <larper@axis.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because we miss to wipe the remainder of i->addr[] in packet_mc_add(),
pdiag_put_mclist() leaks uninitialized heap bytes via the
PACKET_DIAG_MCLIST netlink attribute.
Fix this by explicitly memset(0)ing the remaining bytes in i->addr[].
Fixes: eea68e2f1a00 ("packet: Report socket mclist info via diag module") Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@parallels.com> Acked-by: Pavel Emelyanov <xemul@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For local routes that require a particular output interface we do not want
to cache the result. Caching the result causes incorrect behaviour when
there are multiple source addresses on the interface. The end result
being that if the intended recipient is waiting on that interface for the
packet he won't receive it because it will be delivered on the loopback
interface and the IP_PKTINFO ipi_ifindex will be set to the loopback
interface as well.
This can be tested by running a program such as "dhcp_release" which
attempts to inject a packet on a particular interface so that it is
received by another program on the same board. The receiving process
should see an IP_PKTINFO ipi_ifndex value of the source interface
(e.g., eth1) instead of the loopback interface (e.g., lo). The packet
will still appear on the loopback interface in tcpdump but the important
aspect is that the CMSG info is correct.
Signed-off-by: Allain Legacy <allain.legacy@windriver.com>
Signed off-by: Chris Friesen <chris.friesen@windriver.com> Reviewed-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building wilc1000 with clang currently fails in the staging-next branch:
drivers/staging/wilc1000/wilc_spi.c:123:34: warning: tentative definition of variable with internal linkage has incomplete non-array type 'const struct wilc1000_ops' [-Wtentative-definition-incomplete-type]
static const struct wilc1000_ops wilc1000_spi_ops;
The reason is that wilc1000_ops was left behind after a recent cleanup,
and is completely unused and also uninitialized and const and has an
incomplete type.
Removing the variable is obviously correct, and gets rid of the warning.
No idea why gcc does not complain about it though.
There are several reports of freeze on enabling HWP (Hardware PStates)
feature on Skylake-based systems by the Intel P-states driver. The root
cause is identified as the HWP interrupts causing BIOS code to freeze.
HWP interrupts use the thermal LVT which can be handled by Linux
natively, but on the affected Skylake-based systems SMM will respond
to it by default. This is a problem for several reasons:
- On the affected systems the SMM thermal LVT handler is broken (it
will crash when invoked) and a BIOS update is necessary to fix it.
- With thermal interrupt handled in SMM we lose all of the reporting
features of the arch/x86/kernel/cpu/mcheck/therm_throt driver.
- Some thermal drivers like x86-package-temp depend on the thermal
threshold interrupts signaled via the thermal LVT.
- The HWP interrupts are useful for debugging and tuning
performance (if the kernel can handle them).
The native handling of thermal interrupts needs to be enabled
because of that.
This requires some way to tell SMM that the OS can handle thermal
interrupts. That can be done by using _OSC/_PDC in processor
scope very early during ACPI initialization.
The meaning of _OSC/_PDC bit 12 in processor scope is whether or
not the OS supports native handling of interrupts for Collaborative
Processor Performance Control (CPPC) notifications. Since on
HWP-capable systems CPPC is a firmware interface to HWP, setting
this bit effectively tells the firmware that the OS will handle
thermal interrupts natively going forward.
For details on _OSC/_PDC refer to:
http://www.intel.com/content/www/us/en/standards/processor-vendor-specific-acpi-specification.html
To implement the _OSC/_PDC handshake as described, introduce a new
function, acpi_early_processor_osc(), that walks the ACPI
namespace looking for ACPI processor objects and invokes _OSC for
them with bit 12 in the capabilities buffer set and terminates the
namespace walk on the first success.
Also modify intel_thermal_interrupt() to clear HWP status bits in
the HWP_STATUS MSR to acknowledge HWP interrupts (which prevents
them from firing continuously).
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject & changelog, function rename ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b12:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: Akash Goel <akash.goel@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B Fixes: 8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
(cherry picked from commit 8a292d016d1cc4938ff14b4df25328230b08a408) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.
This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.
v2:
- Add a code comment about the relation of this fix to the freeze/thaw
vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
and device enable calls. (Chris)
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c41760c0 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980 Fixes: 5008e874edd34 ("drm/i915: Make wait_for_flips interruptible.") Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.uk Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit acf4e84d6167317ff21be5c03e1ea76ea5783701) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If i2c_device_id *id is NULL and acpi_match_device returns NULL too,
then chipset may be unitialized when accessing &ak_def_array[chipset] in
ak8975_probe. Therefore initialize chipset to AK_MAX_TYPE, which will
return an error when not changed.
This patch fixes the following maybe-uninitialized warning:
drivers/iio/magnetometer/ak8975.c: In function ‘ak8975_probe’:
drivers/iio/magnetometer/ak8975.c:788:14: warning: ‘chipset’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
data->def = &ak_def_array[chipset];
Signed-off-by: Richard Leitner <dev@g0hl1n.net> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In certain probe conditions the interrupt came right after registering
the handler causing a NULL pointer exception because of uninitialized
waitqueue:
$ udevadm trigger
i2c-gpio i2c-gpio-1: using pins 143 (SDA) and 144 (SCL)
i2c-gpio i2c-gpio-3: using pins 53 (SDA) and 52 (SCL)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = e8b38000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: snd_soc_i2s(+) i2c_gpio(+) snd_soc_idma snd_soc_s3c_dma snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer snd soundcore ac97_bus spi_s3c64xx pwm_samsung dwc2 exynos_adc phy_exynos_usb2 exynosdrm exynos_rng rng_core rtc_s3c
CPU: 0 PID: 717 Comm: data-provider-m Not tainted 4.6.0-rc1-next-20160401-00011-g1b8d87473b9e-dirty #101
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(...)
(__wake_up_common) from [<c0379624>] (__wake_up+0x38/0x4c)
(__wake_up) from [<c0a41d30>] (ak8975_irq_handler+0x28/0x30)
(ak8975_irq_handler) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389c40>] (handle_edge_irq+0xf0/0x19c)
(handle_edge_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c05ee360>] (exynos_eint_gpio_irq+0x50/0x68)
(exynos_eint_gpio_irq) from [<c0386720>] (handle_irq_event_percpu+0x88/0x140)
(handle_irq_event_percpu) from [<c038681c>] (handle_irq_event+0x44/0x68)
(handle_irq_event) from [<c0389a70>] (handle_fasteoi_irq+0xb4/0x194)
(handle_fasteoi_irq) from [<c0385e04>] (generic_handle_irq+0x24/0x34)
(generic_handle_irq) from [<c03860b4>] (__handle_domain_irq+0x5c/0xb4)
(__handle_domain_irq) from [<c0301774>] (gic_handle_irq+0x54/0x94)
(gic_handle_irq) from [<c030c910>] (__irq_usr+0x50/0x80)
The bug was reproduced on exynos4412-trats2 (with a max77693 device also
using i2c-gpio) after building max77693 as a module.
Fixes: 94a6d5cf7caa ("iio:ak8975 Implement data ready interrupt handling") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this there was a double free of the metadata,
which ended up freeing the fd table for me here, and taking
out the machine more often than not.
I reproduced with X.org + modesetting DDX + latest llvm/mesa,
also required using dri3.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If of_node is set before calling platform_device_add, the driver core
will try to use of: modalias matching, which fails because the device
tree nodes don't have a compatible property set. This patch fixes
imx-ipuv3-crtc module autoloading by setting the of_node property only
after the platform modalias is set.
Fixes: 304e6be652e2 ("gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports") Reported-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-By: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the consumer side, we have interrupt driven flow management of the
producer. It is sufficient to base the signaling decision on the
amount of space that is available to write after the read is complete.
The current code samples the previous available space and uses this
in making the signaling decision. This state can be stale and is
unnecessary. Since the state can be stale, we end up not signaling
the host (when we should) and this can result in a hang. Fix this
problem by removing the unnecessary check. I would like to thank
Arseney Romanenko <arseneyr@microsoft.com> for pointing out this issue.
Also, issue a full memory barrier before making the signaling descision
to correctly deal with potential reordering of the write (read index)
followed by the read of pending_sz.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the issue where the mxs_ocotp_read is reading
the ocotp in reg_size steps but decrements the remaining size
by 1. The number of iterations is thus four times higher,
overwriting the area behind the output buffer.
Fixes: c01e9a11ab6f ("nvmem: add driver for ocotp in i.MX23 and i.MX28") Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Stanislav Meduna <stano@meduna.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices that after having been reset during resume need to be rebound
due to a missing reset_resume callback, are now left in a suspended
state. This specifically broke resume of common USB-serial devices,
which are now unusable after system suspend (until disconnected and
reconnected) when USB persist is enabled.
During resume, usb_resume_interface will set the needs_binding flag for
such interfaces, but unlike system resume, run-time resume does not
honour it.
Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Link ECU is an aftermarket ECU computer for vehicles that provides
full tuning abilities as well as datalogging and displaying capabilities
via the USB to Serial adapter built into the device.
Signed-off-by: Mike Manning <michael@bsch.com.au> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some SOCs PORTS_IMPL register value is never programmed by the
firmware and left at zero value. Which means that no sata ports are
available for software. AHCI driver used to cope up with this by
fabricating the port_map if the PORTS_IMPL register is read zero,
but recent patch broke this workaround as zero value was valid for
NVMe disks.
This patch adds ports-implemented DT bindings as workaround for this issue
in a way that DT can can override the PORTS_IMPL register in cases where
the firmware did not program it already.
In usecases where force_port_map is used saved_port_map is never set,
resulting in not programming the PORTS_IMPL register as part of initial
config. This patch fixes this by setting it to port_map even in case
where force_port_map is used, making it more inline with other parts of
the code.
using the "r" constraint for %2. r0 is a valid register in the "r" set,
but addi X,r0,X turns it into an li:
li r7,-1
andc r7,r7,r0
popcntd r4,r7
Fix this by using the "b" constraint, for which r0 is not a valid
register.
This was found with a kernel build using gcc trunk, narrowed down to
when -frename-registers was enabled at -O2. It is just luck however
that we aren't seeing this on older toolchains.
Thanks to Segher for working with me to find this issue.
Fixes: d0cebfa650a0 ("powerpc: word-at-a-time optimization for 64-bit Little Endian") Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new ports-implemented mask, which is required to get
achi working on the mainline. Without this patch value read from
PORTS_IMPL register which is zero would not enable any ports for
software to use.
The code for checking whether a BAR address range is valid will break
out of the loop when a start address of 0x0 is encountered.
This behaviour is wrong since by breaking out of the loop we may miss
the BAR that describes the EFI frame buffer in a later iteration.
Because of this bug I can't use video=efifb: boot parameter to get
efifb on my new ThinkPad E550 for my old linux system hard disk with
3.10 kernel. In 3.10, efifb is the only choice due to DRM/I915 not
supporting the GPU.
This patch also add a trivial optimization to break out after we find
the frame buffer address range without testing later BARs.
Signed-off-by: Wang YanQing <udknight@gmail.com>
[ Rewrote changelog. ] Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Reviewed-by: Peter Jones <pjones@redhat.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/1462454061-21561-2-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reviewing a different change to asm-generic/io.h Arnd spotted that
ARC ioread32 and ioread32be both of which come from asm-generic versions
are not symmetrical in terms of calling the io barriers.
The sti-cpufreq does unconditional registration of the cpufreq-dt driver
which causes issue on an multi-platform build. For example, on Vexpress
TC2 platform, we get the following error on boot:
cpu cpu0: OPP-v2 not supported
cpu cpu0: Not doing voltage scaling
cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table
for cpu:0, -19
cpu cpu0: dev_pm_opp_get_max_volt_latency: Invalid regulator (-6)
...
arm_big_little: bL_cpufreq_register: Failed registering platform driver:
vexpress-spc, err: -17
The actual driver fails to initialise as cpufreq-dt is probed
successfully, which is incorrect. This issue can happen to any platform
not using cpufreq-dt in a multi-platform build.
This patch adds a check to do selective initialization of the driver.
Fixes: ab0ea257fc58 (cpufreq: st: Provide runtime initialised driver for ST's platforms) Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not load one entry beyond the end of the syscall table when the
syscall number of a traced process equals to __NR_Linux_syscalls.
Similar bug with regular processes was fixed by commit 3bb457af4fa8
("[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls").
arm_cpuidle_suspend() may return -EOPNOTSUPP, or any value returned
by the cpu_ops/cpuidle_ops suspend call. arm_enter_idle_state() doesn't
update 'ret' with this value, meaning we always signal success to
cpuidle_enter_state(), causing it to update the usage counters as if we
succeeded.
Fixes: 191de17aa3c1 ("ARM64: cpuidle: Replace cpu_suspend by the common ARM/ARM64 function") Signed-off-by: James Morse <james.morse@arm.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark reported that having asterisks on the end of directory names
confuses get_maintainer.pl when it encounters subdirectories, and that
my name does not appear when run on drivers/firmware/efi/libstub.
Reported-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/1462303781-8686-2-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 947e9762a8dd ("writeback: update wb_over_bg_thresh() to use
wb_domain aware operations") unintentionally changed this function's
meaning from "are there more dirty pages than the background writeback
threshold" to "are there more dirty pages than the writeback threshold".
The background writeback threshold is typically half of the writeback
threshold, so this had the effect of raising the number of dirty pages
required to cause a writeback worker to perform background writeout.
This can cause a very severe performance regression when a BDI uses
BDI_CAP_STRICTLIMIT because balance_dirty_pages() and the writeback worker
can now disagree on whether writeback should be initiated.
For example, in a system having 1GB of RAM, a single spinning disk, and a
"pass-through" FUSE filesystem mounted over the disk, application code
mmapped a 128MB file on the disk and was randomly dirtying pages in that
mapping.
Because FUSE uses strictlimit and has a default max_ratio of only 1%, in
balance_dirty_pages, thresh is ~200, bg_thresh is ~100, and the
dirty_freerun_ceiling is the average of those, ~150. So, it pauses the
dirtying processes when we have 151 dirty pages and wakes up a background
writeback worker. But the worker tests the wrong threshold (200 instead of
100), so it does not initiate writeback and just returns.
Thus, balance_dirty_pages keeps looping, sleeping and then waking up the
worker who will do nothing. It remains stuck in this state until the few
dirty pages that we have finally expire and we write them back for that
reason. Then the whole process repeats, resulting in near-zero throughput
through the FUSE BDI.
The fix is to call the parameterized variant of wb_calc_thresh, so that the
worker will do writeback if the bg_thresh is exceeded which was the
behavior before the referenced commit.
When configuring a pfn-device instance to allocate the memmap array it
needs to account for the fact that vmemmap_populate_hugepages()
allocates struct page blocks in HPAGE_SIZE chunks. We need to align the
reserved area size to 2MB otherwise arch_add_memory() runs out of memory
while establishing the memmap:
_batadv_update_route rcu_derefences orig_ifinfo->router outside of a
spinlock protected region to print some information messages to the debug
log. But this pointer is not checked again when the new pointer is assigned
in the spinlock protected region. Thus is can happen that the value of
orig_ifinfo->router changed in the meantime and thus the reference counter
of the wrong router gets reduced after the spinlock protected region.
Just rcu_dereferencing the value of orig_ifinfo->router inside the spinlock
protected region (which also set the new pointer) is enough to get the
correct old router object.
Fixes: e1a5382f978b ("batman-adv: Make orig_node->router an rcu protected pointer") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When removing a single interface while a broadcast or ogm packet is
still pending then we will free the forward packet without releasing the
queue slots again.
This patch is supposed to fix this issue.
Fixes: 6d5808d4ae1b ("batman-adv: Add missing hardif_free_ref in forw_packet_free") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
[sven@narfation.org: fix conflicts with current version] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The encapsulated ethernet and VLAN header may be outside the received
ethernet frame. Thus the skb buffer size has to be checked before it can be
parsed to find out if it encapsulates another batman-adv packet.
Fixes: 420193573f11 ("batman-adv: softif bridge loop avoidance") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that DAT is VLAN aware, it must use the VID when
computing the DHT address of the candidate nodes where
an entry is going to be stored/retrieved.
Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by: Antonio Quartulli <a@unstable.cc>
[sven@narfation.org: fix conflicts with current version] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Khugepaged attempts to raise min_free_kbytes if its set too low.
However, on boot khugepaged sets min_free_kbytes first from
subsys_initcall(), and then the mm 'core' over-rides min_free_kbytes
after from init_per_zone_wmark_min(), via a module_init() call.
Khugepaged used to use a late_initcall() to set min_free_kbytes (such
that it occurred after the core initialization), however this was
removed when the initialization of min_free_kbytes was integrated into
the starting of the khugepaged thread.
The fix here is simply to invoke the core initialization using a
core_initcall() instead of module_init(), such that the previous
initialization ordering is restored. I didn't restore the
late_initcall() since start_stop_khugepaged() already sets
min_free_kbytes via set_recommended_min_free_kbytes().
This was noticed when we had a number of page allocation failures when
moving a workload to a kernel with this new initialization ordering. On
an 8GB system this restores min_free_kbytes back to 67584 from 11365
when CONFIG_TRANSPARENT_HUGEPAGE=y is set and either
CONFIG_TRANSPARENT_HUGEPAGE_ALWAYS=y or
CONFIG_TRANSPARENT_HUGEPAGE_MADVISE=y.
Fixes: 79553da293d3 ("thp: cleanup khugepaged startup") Signed-off-by: Jason Baron <jbaron@akamai.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If /proc/<PID>/environ gets read before the envp[] array is fully set up
in create_{aout,elf,elf_fdpic,flat}_tables(), we might end up trying to
read more bytes than are actually written, as env_start will already be
set but env_end will still be zero, making the range calculation
underflow, allowing to read beyond the end of what has been written.
Fix this as it is done for /proc/<PID>/cmdline by testing env_end for
zero. It is, apparently, intentionally set last in create_*_tables().
This bug was found by the PaX size_overflow plugin that detected the
arithmetic underflow of 'this_len = env_end - (env_start + src)' when
env_end is still zero.
The expected consequence is that userland trying to access
/proc/<PID>/environ of a not yet fully set up process may get
inconsistent data as we're in the middle of copying in the environment
variables.
A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
projects / thirdparty / kernel / stable.git / log
